8
W3400V Four-port ADSL 2+ Wireless Router Quick Installation Guide VER: 1.1

Innacomm W3400V_Quick Installation Guide

Embed Size (px)

DESCRIPTION

Innacomm W3400V_Quick Installation Guide

Citation preview

W3400V

Four-port ADSL 2+ Wireless Router

Quick Installation Guide

VER: 1.1

1

1 Hardware Installation Step 1 See the following figure. Connect the Line port of the DSL Router with a

telephone cable. Step 2 Connect the LAN port of the DSL Router to the network card of the PC via an

Ethernet cable. Step 3 Plug one end of the power adapter to the wall outlet and connect the other

end to the Power port of the DSL Router.

2 Web-Based Management

2.1 PC Network Configuration Each network interface on the PC should either be configured with a statically defined IP address and DNS address, or be instructed to automatically obtain an IP address using the network DHCP server. DSL router provides a DHCP server on its LAN and it is recommended to configure your LAN to automatically obtain its IP address and DNS server IP address. The configuration principle is identical but should be carried out differently on each operating system.

2

The following displays the TCP/IP Properties dialog box as it appears on Windows XP.

TCP/IP configuration instructions for Windows XP are as follows.

Step 1 Choose Start > Control Panel > Network Connections from the desktop.

Step 2 Right-click the Ethernet connection icon and choose Properties. Step 3 On the General tab, select the Internet Protocol (TCP/IP) component

and click Properties. Step 4 The Internet Protocol (TCP/IP) Properties window appears. Step 5 Select the Obtain an IP address automatically radio button. Step 6 Select the Obtain DNS server address automatically radio button. Step 7 Click OK to save the settings.

By default, the IP address address of the router is 192.168.1.1 . The IP address of the PC can be set to 192.168.1.x (2 to 254), subnet mask to 255.255.255.0, default gateway to 192.168.1.1.

3

2.2 Logging In to the Router When you log in to the DSL Router for the first time, the login wizard appears.

Step 1 Open a Web browser on your computer. Step 2 Enter http://192.168.1.1 (default IP address of the DSL router) in the

address bar. The login page appears. Step 3 Enter a user name and the password. The default username and

password of common user are tmuser and tmuser respectively. The default username and password of super user are tmadmin and tmadmin respectively.

Step 4 Click Login to log in or click Clear to exit the login page.

After logging in to the DSL router as super user, you can view and configure the router, such as wireless parameters, WAN connection. When you logging in to the DSL router as common user, you can view and diagnose the system of router, and configure Quick Setup only.

2.3 Wireless Key Configuration Logging in to the DSL router as super user, choose Wireless > Security, and the following page appears. In this page, you can configure wireless key as you want. The default Current Network Key is 1, and the default Network Key 1 is 1234567890123. After proper configurations, click Save/Apply to take the settings effect.

4

2.4 WAN Connection Configuration

2.4.1 Bridge Mode of Factory Default Configuration If the router is in the factory default mode, the following page appears when you logging in to the DSL router as common user. In this condition, the router is in the bridge mode, you can contact 100 for further assistance and support, or creat Internet connection as 4 section. If you want to configure the more paramerers of WAN connection and another parameters, please logging in to the DSL router as super user. Then you can modify the WAN connection in Quick Setup or Advanced Setup.

5

2.4.2 PPP Mode If the router is in the PPPoE or PPPoA mode, the following page appears when you logging in to the DSL router as common user. In this page, you can configure the Quick Setup. Choose Quick Setup, the following page appears.

Enter Streamyx ID and Streamyx Password provided by your ISP.

Enable wireless: The default value is enabled. SSID: For added security, you should change the default SSID to a unique

name. Wireless Channel: The default value is auto, you can select it from the

drop-down list. The valuable value is from 1 to 11. Enable Security: If you enable it, the following page appears. Enter 13

ASCII characters for the network key.

6

After proper configurations, click Save/Reboot to take the configurations into effect.

3 Internet Connection

3.1 DSL Router Connection You can connect to the DSL router by Ethernet cable or WLAN.

Use an Ethernet cable to connect an LAN port of your DSL router and the network card of your computer.

Choose Network Connections > Wireless Network Connection to search the SSID of the router, then select the connection. When the page appears that requires the authentication key, enter the wireless key that you change before, or enter the default wireless key: 1234567890123.

3.2 Dialer Connection for Internet

3.2.1 Creating DSL-Dialer Connection for Internet Step 1 Select the installation file of DSL-Dialer, such as setup_innacomm.exe. Step 2 Install the DslDialer according to the instructions. Step 3 Choose Start > Programs > DslDialer, and the following page appears.

In this page, enter the user name and password provided by ISP. Click Connect to start Internet connection.

3.2.2 Creating Dialer Connection for Internet Manually Step 1 Choose Start > Control Panel > Network Connections from the

desktop.

7

Step 2 Select Create a new connection. Step 3 Start the new connection wizard. Step 4 Select the Connect to the Internet as the Network connection type. Step 5 In the shown page, select the Set up my connection manually radio

button. Step 6 In the shown page, select the Connect using a broadband connection

that requires a user name and password radio button. Step 7 In the shown page, enter the name of your ISP. Step 8 In the shown page, select the Anyone’s use or My use only radio

button. Step 9 In the shown page, enter the user name and password provided by your

ISP. Step 10 Complete the new connection wizard. Step 11 Choose Network Connections, then select the new connection that you

create above, the following page appears. In this page, enter the user name and password provided by your ISP. Click Connect to start Internet connection.