INDUSTRIAL TRAINING REPORT

ON

OPTICAL FIBERS IN

COMMUNICATION

Sponsored by

NCS Computech Pvt. Ltd.

We Deliver “ Safe, Secure and Managed IT Infrastructure”.

(Submitted In partial fulfillment for the award of “Bachelor of Technology” degree in

Computer Science Engineering of Rajasthan Technical University, Kota)

DEPARTMENT OF COMPUTER SCIENCE ENGINEERING

Session-2010-2011

Guided by: Submitted by:

Mr. Narendra pandey Ashok Dhakar

(Techno Vantage) B.Tech (Computer Sc. Engg.) NCS Computech Pvt. Ltd. VII Semester

Jaipur 07ECICS017

Br. Office-D157/A/B Durga Marg, Bani Park, Jaipur-302016

No.NCS/JPR/Mgr.(tag)/2010 /0517 Date:-19/06/2010

CERTIFICATE

This is to certify that “Ashok Dhakar” completed their Industrial training from “14th MAY 2010 to 19th JUNE 2010” in my supervision in partial fulfillment for the Degree of “BACHELOR OF TECHNOLOGY”.

During the training, he has worked on “Optical Fibers In Communication” in Telecommunication Networking. His overall performance during the period was Very Good.

I wish him success in life.

Mr. Narendra Pandey

(Training Incharge)

ACKNOWLEDGEMENT

With the completion of the training my experience at the firm was excellent. The task of

undertaking the training travelled through a dynamic experience. With the constant guidance,

valuable suggestions, timely help and heart warming encouragement rendered to me by Mr.

Narendra Pandey the firm served as an excellent learning platform. During the course of the

training I came through the working pattern of the office along with professionalism. Also the

basic practical experience at the site helped a lot. Theoretical discussions, off-site situation

handling and on-site experience are to name a few of the environments to which I was

exposed. Along with it I was given enough opportunities and encouragement to think

independently in various problem solving situations.

I would also like to thank our lab technicians for their help and cooperation

throughout our project.

I would like to express my thanks to all those people who directly or indirectly supported

me throughout my term for the training.

Above all I want to thank Mr. N. Chandra, Dean of our college for recommending me to

the practical training; and Mr. Narendra Pandey for inducting me into the firm as

a trainee.

Thanking you sincerely,

Ashok Dhakar

PREFACE

Industrial training is one of the most important components in the fulfillment of any

engineering course conducted at any level at any college. Each and every one of us would

always have an added advantage if I have a chance to come face to face with the equipments

and the processes I am being taught in my engineering course .The main purpose of the

training program is to expose the trainees to practical experience of the actual industrial

conditions in which they are required to work in future.

I deem it a privilege to have undergone training in an organization, which has allowed me to

see the actual working of the software industry. At the department of information technology;

I have been given the chance to be familiar with new technologies.

Ashok dhakar

DECLARATIONDECLARATION

I hereby declare that the Industrial Training work entitled “Optical Fibers In

Communication” is an authentic record of my own work carried out at NCS Computech

Pvt. Ltd. , Jaipur as per the requirement of ONE month Industrial Training project for the

award of degree of BACHELOR OF TECHNOLOGY at CompuCom Institute of

Management & Information Technology Sitapura, Jaipur, under the guidance of Mr.

Narendra Pandey during ‘12th May 2010 to 18th June’ 2010.

Place: Jaipur

Date: 18th June 2010 Ashok Dhakar

It is certified that the above statement made by the students is correct to the best of our

knowledge and belief.

Mr. Narendra Pandey

(Training incharge)

ABSTRACT

Communication is an important part of our daily life. The communication process involves

information generation, transmission, reception and interpretation. As needs for various types

of communication such as voice, images, video and data communications increase demands

for large transmission capacity also increase. This need for large capacity has driven the rapid

development of light wave technology; a worldwide industry has developed. An optical or

light wave communication system is a system that uses light waves as the carrier for

transmission. An optical communication system mainly involves three parts. Transmitter,

receiver and channel. In optical communication transmitters are light sources, receivers are

light detectors and the channels are optical fibers. In optical communication the channel i.e,

optical fibers play an important role because it carries the data from transmitter to the

receiver. Hence, here we shall discuss mainly about optical fibers.

NCS Computech Profile

Who are we

Incorporated in March, 1994 NCS group has business interest in IT

services, Training,  Organic Crop Care, Food Processing and Waste Management and

recycling.  After laying the foundation NCS group has been witnessing and yearly growth of

over 100 Percent since 2002. The group is expanding its geographical  footprint and

has offices  and operations across India.

Living the key concept “Navigating Concepts to Solutions”

All NCS businesses have some key concepts to work upon. There is a constant flux of ideas

moving around in the group. The core team constantly keeps on working on these concepts

to figure out the best possible solution from that. It is not only about new product ideas; it is

about the processes, methods, means and at times well the philosophy behind the working.   

The   NCS Culture   that makes the Magic Concept Work

NCS culture is what distinguishes us from the crowd.  Mistakes are well come. That means

we are experimenting with new concepts. NCS stimulates the human capital to experiment

with new concepts regularly.

NCS team keeps working on simple ideas, simple implementation and simplification of so

called complex things. If you mingle with NCS culture, you may be surprised by the

simplicity with which business happens and gets executed. 

At NCS, Wisdom denotes the pursuing of the best ends by the best means. Thus, the Means

are as important as the Ends.

Management Team

Manohar Malani (41 Years), Managing Director & CEO :  An Engineer from University

of Pune and now a business leader.  Handles many caps and juggles between them with

ease.  A Leader in himself and has a special skill of creating leaders.

This coupled with his business vision has been instrumental in the diversification of

NCS in various areas. 

He has been instrumental in establishing the  marketing and support base of Quick Heal

since 1994 through 2002 as Director Business Development.  

Rajkumar Damani (48 Years):  A commerce graduate and a work horse.  A street fighter

and an example of the adage “appearances are deceptive”. Holds the portfolio of

Marketing Director. Leads the team from the front and even today ensures that he explore

and creates new market himself regularly. This keeps the team motivated to go to

unexplored markets and work hard. 

Sandeep Tambi (36 Years):  His understanding of technology and knack of developing

relationship makes him ideal for creating new opportunities. He also shares the

responsibilities of delivering training, seminars to channel partners and customers. With

now 10 years of experience in the field of IT security he is also instrumental in creating

market for new and niche products dealt by NCS.

Apart from the Trio NCS has a great 2nd rung of leadership and execution team of over 20

powerful team members to carry the business to dizzling heights.

Advisory Board:

Poonam Chand Malani (76 Years), Chairman: The father figure and source of

inspiration. His rich experience has helped the company learn the art of doing things

economically with great returns.  He had been instrumental in bringing discipline of all

nature in the organization otherwise driven by young blood.

Manmohan Malani (45 Years), Director : An homeopath doctor by profession who has

chosen to be into business rather than profession. He has across the years developed a good

knack at accounts and taxation and offers valuable advice.

Shyamal Chatterjee (56 years), Director : The experience of handling various complicated

matters reflects when you meet him. Has been handling various business challanges for last

30 years.  An LLB by qualification, his advice has great value for the company. 

  Services

Managed IT Services

An IT structure well designed, developed, implemented and executed plays a vital role in a

business’s return on the investment in its IT Plan. Maximum mileages, lower cost, speed and

efficiency in delivery plays a major role that fuels a business success.

NCS recognizes this business need and can put together a complete team for a total or

scalable solution capitalizing the latest technologies and its vast global talent pool from its

locations in India.

Collaboration with NCS revolves on a true partnership with our customers. The success of

our partnership is achieved by our recognition of the specific needs that each of our customer

requires and coming up with a tailor fit plan that addresses those needs.

NCS specializes in areas of Application Development and Application Managed Services.

Our substantial advantages in these areas include

Business knowledge SMEs

Talent pool across continents

Right Alliances

Flexible and Easy to maintain development approach

Reliable on time delivery.

Permanant Staffing

In an industry rife with rampant professional migration, sourcing and securing the right kind

of staff is critical to every company’s protracted stability and long-term productivity.

At NCS, we understand the need for individuals with more than just the technical ability to

get the job completed

Work culture in a modern economy is constantly pressured to ‘do more with less’ and the

head count area within an organization is no exception. With changes and technological

advances ever evolving, businesses are ever required to retain, retrain and hire talent that

adapts fast to this nouveau environment to deliver results and maintain profitability.

 

With speed and accuracy in mind, NCS executes its staffing model for the right individual

with the right skills and at the right price. Our staffing model gives importance to every detail

to ensure candidates and the clients are matched in every aspect to understand each one’s

strategic and tactical goals. This ensures a union that is gainfully profitable with amazing

results.

 

IT Staffing

NCS offers a full range of outsourced IT staffing services, backed by IT knowledge and

expertise across technologies and domains. We work closely with an organization’s staffing

department to ensure that IT staffing needs are met based on: pre-defined project metrics or

weekly or monthly staff augumentation programs.

Our IT staffing services provide companies with:

Super-specialties driven human resource solutions across technologies

The flexibility to choose a staffing model that meets short-term, long term and

strategic staffing needs

Dedicated workforce for optimal performance

Experienced professionals for seamless results

The firm's focus on current and emerging new technologies complement the client's in-house

technology skill sets and strengthens their ability to meet business goals, in a timely and cost-

effective manner. 

The key skill our software professionals bring across the table:

ERP 

SAP, Oracle Applications, Peoplesoft and Siebel

Operating Systems 

Solaris, UNIX, Linux, Win2Kx/NT, MAC OS 9, OS X 

Microsoft & Other Technologies 

Java, J2EE, JavaBeans, EJB, JSP, Struts, JNI, Sun Portal, Web Sphere, Weblogic,

Vignette, Sun One, MS .NET: C#.NET, ASP.NET, ADO.NET, VB.NET, Web Services 

C++, VC++, MFC, ActiveX, VB, ADO , STL, HTML, DHTML, XML, IIS/ASP, PHP, Perl 

CORBA/IIOP, RMI, WAP and DCOM 

Database 

Oracle, DB2, MS-SQL, Sybase, Informix 

Data warehousing 

ETL, Informatica, Erwin, Ab Initio, Hyperion, Teradata etc.

Telecommunication Networking

Optical Fiber, Lan messenger etc.

Our IT staffing services are designed to provide you with optimal staffing solutions that

accurately assess and manage your manpower requirements enabling your core team to

effectively focus on critical assignments and effectively execute their responsibilities.

Partners Of NCS

QuickHeal Technologies Quick Heal Technologies is leading provider of AntiVirus and Internet Security tools and

is leader in Anti-Virus Technology in India. A privately held company, Quick Heal

Technologies Pvt. Ltd. (formerly known as Cat Computer Services (P) Ltd.) was founded in

1993 and has been actively involved in Research and Development of anti-virus software

since then.

Serving more than million users worldwide, Quick Heal Technologies employs more than

200 people in sixteen branches and its headquarters is in Pune, India. Quick Heal an

award-winning anti-virus product is installed in corporate, small business and consumers'

homes, protecting their PCs from viruses and other malicious threats.

Quick Heal Technologies was formed for catering the demand of highly reliable anti-virus

software, which would successfully tackle the growing number of virus problems. Quick

Heal Technologies (P) Ltd. was founded by Mr. Kailash Katkar and Mr. Sanjay Katkar in

the year 1993. 

2008

April : Quick Heal AntiVirus Plus 2008 has received West Coast Labs' acclaimed

Check-Mark certification on Windows Vista Business Edition.

February : Quick Heal Technologies has received Antivirus + Antispyware

OESISOKTM designation for Quick Heal AntiVirus Version 9.50 on

Windows XP Operating system in accordance with the OPSWAT testing

criteria.

January : Quick Heal India’s leading antivirus software walked another step achieving

Microsoft Certified Partner Level from Microsoft.

 

 Tectona SoftSolutions (P) Ltd.

Tectona is a Software Incubator based at Ahmedabad, Gujarat. Simplifying the IT

infrastructure management is the area of focus at Tectona. Their winning products include

Enterprise Management Platform- OwnYIT and Remote infrastructure Managed Platform-

AssertYIT

  Vembu Technologies

Founded in 2004, Vembu Technologies is a leader in providing cost effective, network

based, disk to disk backup software solutions. Vembu's flagship product StoreGrid, which

backs up desktops and servers, comes in three editions. StoreGrid Service Provider Edition

powers the managed online backup services business of thousands of MSPs, VARs, ISPs and

Managed Hosting Providers. StoreGrid Professional and Education Editions are trusted by

thousands of SMBs and educational institutions for on-premise and centralized backups for

their heterogeneous environments.

Vembu has won many awards and has been recognized by various leading industry bodies.

Achievements include the Deloitte Technology Fast 50 Award and the "Red Herring 100

Asia" list of innovative companies. Vembu has regularly been featured on CRN's annual

Emerging Vendors list, and was a finalist for a VAR Business Tech Innovator award and the

Windows IT Pro award for Interoperability. Vembu is also actively involved with various

industry bodies including MSP Partners & MSP Mentor.

Vembu Technologies is led by an accomplished management team - graduates from some of

the best universities in the world who bring with them decades of diverse industry experience

from across various domains. Vembu takes great pride in its exceptionally passionate team

and its core values, the most important of which is that of always placing its customers' &

partners' interests first in everything the company does. This is especially reflected in the

fanatical customer support Vembu offers its customers.

The company is headquartered in Chennai, India.

INDEX

S.NO. CONTENT1. History2. Introduction3. Fundamental of Optical Fiber4. Construction of Fibers5. Classification of Optical Fibers

5.1 Based on the materials used 5.2 Based on number of modes 5.3 Based on refractive index

6. Modes And Propagation Of Light In Fibers7. Optical Fiber Cabels8. Joint of Fiber9. Fiber Splices10. Fusion Splices11. Equipment Required for OFC Joint12. Electric Field With In Fiber Cladding 13. Repeaters And Regenerators14. Light Sources15. Detecting the Signal16. Advantages Over Conventional Cables17. Application of the Optical Fiber Communication18. Features19. Essential Features of an Optical Fiber20. Drawbacks of Optical Fiber Communication 21. Conclusions 22. Bibliography

Optical Fibers in Communication

1. HISTORY:-The use of visible optical carrier waves or light for communication has been common for

many years. Simple systems such as signal fires, reflecting mirrors and, more recently

signaling lamps have provided successful, if limited, information transfer. Moreover as

early as 1880 Alexander Graham Bell reported the transmission of speech using a light

beam. The photo phone proposed by Bell just for years after the invention of the

telephone modulated sunlight with a diaphragm giving speech transmission over a

distance of 200m.

However, although some investigation of the optical communication continued in the

early part of the 20th century its use was limited to mobile, low capacity communication

links. This was due to both the lack of suitable light sources and the problem that light

transmission in the atmosphere is restricted to line of sight and severely affected by

disturbances such as rain, snow, fog dust and atmospheric turbulence.

A renewed interest in optical communication was stimulated in the early 1960s with the

invention of the laser. This device provided a coherent light source, together with the

possibility of the modulation at high frequency.

The proposals for optical communication via optical fibers fabricated from glass to avoid

degradation of the optical signal by the atmosphere were made almost simultaneously in

1966 by Kao and Hock ham and Werts. Such systems were viewed as a replacement for

coaxial cable system, initially the optical fibers exhibited very high attenuation and were

therefore not comparable with the coaxial cable they were to replace. There were also

problems involved in jointing the fiber cables in a satisfactory manner to achieve low loss

and to enable the process to be performed relatively easily and repeatedly in the field.

In coaxial system the channel capacity is 300 to 10800 and the disadvantages of the

coaxial system are digging, electrical disturbance, in winter cable contracts and breaks

mutual induction. The coaxial cable loss is 0.3db per every km.

• In microwave system if we double the distance the loss will be increased by 6db.

• For the shorter distance the loss is higher.

• In ofc system Optical wire is small size, light weight, high strength and flexibility. Its

transmission benefits includes wide band width, low loss and low cost.

• They are suitable for both analog and digital transmission.

• It is not suffered by digging, electrical interference etc. proble

2. Introduction:-

Optical fibers are arguably one of the world’s most influential scientific developments from

the latter half of the 20th century. Normally we are unaware that we are using them, although

many of us do frequently. The majority of telephone calls and internet traffic at some stage in

their journey will be transmitted along an optical fiber. Why has the development of fibers

been given so much attention by the scientific community when we have alternatives? The

main reason is bandwidth – fibers can carry an extremely large amount of information. More

indirectly, many of the systems that we either rely on or enjoy in everyday life such as banks,

television and newspapers as (to name only a very limited selection) are themselves

dependent on communication systems that are dependent on optical fibers.

3. Fundamentals of Fibers:-

The fundamental principle that makes optical fibers possible is total internal reflection. This

is described using the ray model of light as shown in figure 1.

Figure 1 - Total Internal Reflection

From Snell’s Law we find that refraction (as shown by the dashed line) can only occur when

the angle theta1 is large enough. This implies that as the angle is reduced, there must be a

point when the light ray is reflected, where theta1 = theta2.

The angle where this happens is known as the critical angle and is:

4. CONSTRUCTION OF FIBERS:-

In fibers, there are two significant sections – the core and the cladding. The core is part where

the light rays travel and the cladding is a similar material of slightly lower refractive index to

cause total internal reflection. Usually both sections are fabricated from silica (glass). The

light within the fiber is then continuously totally internally reflected along the waveguide.

Figure 2: Structure of Fiber

When light enters the fiber we must also consider refraction at the interface of the air and the

fiber core. The difference in refractive index causes refraction of the ray as it enters the fiber,

allowing rays to enter the fiber at an angle greater than the angle allowed within the fiber as

shown in the figure 3.

Figure 3 - Acceptance Angle

This acceptance angle, theta, is a crucial parameter for fiber and system designers. More

widely recognized is the parameter NA (Numerical Aperture) that is given by the following

equation:

5. CLASSIFICATION OF OPTICAL FIBERS:-

Optical fibers are classified into three types based on the material used, number of modes and

refractive index.

5.1. Based on the materials used:-

a. Glass fibers:

They have a glass core and glass cladding. The glass used in the fiber is ultra pure, ultra

transparent silicon dioxide (SiO2) or fused quartz. Impurities are purposely added to pure

glass to achieve the desired refractive index

.

b. Plastic clad silica:

This fiber has a glass core and plastic cladding. This performance though not as good as all

glass fibers, is quite respectable.

c. Plastic fibers:

They have a plastic core and plastic cladding. These fibers are attractive in applications

where high bandwidth and low loss are not a concern.

5.2. Based on the number of modes:-

a. Single Mode fiber:

When a fiber wave-guide can support only the HE11 mode, it is referred to as a single mode

wave-guide. In a step index structure this occurs w3hen the wave-guide is operating at v<2.4

where v is dimensionless number which relates the propagating in the cladding. These single

mode fibers have small size and low dopant level (typically 0.3% to 0.4% index elevation

over the lading index.)

In high silica fibers the wave-guide and the material dispersion are often of opposite signs.

This fact can be used conveniently to achieve a single mode fiber of extremely large

bandwidth. Reduced dopant level results in lower attenuation than in multimode fibres. A

single mode wave guide with its large and fully definable bandwidth characteristics is an

obvious candidate for long distance, high capacity transmission applications.

b. Multimode fiber:

It is a fiber in which more than one mode is propagating at the system operating wavelength.

Multimode fiber system does not have the information carrying capacity of single mode

fibers. However they offer several advantages for specific systems.

The larger core diameters result in easier splicing of fibers. Given the larger cores, higher

numerical apertures, and typically shorter link distances, multimode systems can use less

expensive light sources such as LED s . Multimode fibers have numerical apertures that

typically range from 0.2 to 0.29 and have core size that range from 35 to100 micro-meters.

5.3. Based on refractive index:-

a. Step index fiber:

The step index (SI) fiber consists of a central core whose refractive index is n1, surrounded

by a lading whose refractive index is n2, lower than that of core.

Because of an abrupt index change at the core cladding interface such fibers are called step

index fibers.

b. Graded index fibers:

The refractive index of the core in graded index fiber is not constant, but decreases gradually

from its maximum value n1 to its minimum value n2 at the core-cladding interface. The ray

velocity changes along the path because of variations in the refractive index.

The ray propagating along the fiber axis takes the shortest path but travels most slowly, as the

index is largest along this path in medium of lower refractive index where they travel faster.

It is therefore possible for all rays to arrive together at the fiber output by a suitable choice of

refractive index profile.

6. MODES AND PROPAGATION OF LIGHT IN FIBERS:-

Also crucial to understanding fibers is the principle of modes. A more in-depth analysis of the

propagation of light along an optical fiber requires the light to be treated as an

electromagnetic wave (rather that as a ray).

Figure 4 – Modes

The solid line is the lowest order mode shown on figure 4. It is clear that according to the ray

model the lowest order mode will travel down a given length of fiber quicker than the others.

The electromagnetic field model predicts the opposite – that the highest order mode will

travel quicker.

However, the overall effect is still the same – if a signal is sent down the fiber as

several modes then as it travels along the fibre the pulse will spread out, this can lead to the

pulses merging and becoming indistinguishable.

Figure 5: Propagation of light in fibers

The propagation of light is as shown in figure 5. When light ray enters the core with an angle

strikes the surface of cladding whose refractive index is less than that of core. As the

incidence angle on surface of the cladding is greater than or equal to critical angle total

internal reflection takes place. Hence the ray is reflected back into the core in the

forward direction. This process continues until it reaches other end of the cable.

7. OPTICAL FIBER CABLES:-

When optical fibers are to be installed in a working environment their mechanical

properties are of prime importance. In this respect the unprotected optical fiber has

several disadvantages with regard to its strength and durability.

Bare glass fibers are little

and have small cross sectional areas which make them very susceptible to damage when

employing normal transmission line handling procedures. It is therefore necessary to cover

the fibers to improve their tensile strength and to protect them against external influences.

.

The functions of the optical cable may be summarized into four main areas.

These are as follows:-

1. Fiber protection. The major function of the optical cable is to protect against fiber

damage and breakage both during installation and throughout the life of the fiber.

2. Stability of the fiber transmission characteristics. The cabled fiber must have good

stable transmission characteristics which are comparable with the uncabled fiber.

Increases in optical attenuation due to cabling are quite usual and must be minimized

within the cable design.

3. Cable strength. Optical cables must have similar mechanical properties to electrical

transmission cables in order that they may be handled in the same manner. These

mechanical properties include tension, torsion, compression, bending, squeezing and

vibration. Hence the cable strength may be improved by incorporating a suitable

strength member and by giving the cable a properly designed thick outer sheath

.4. Identification and jointing of the fibers within the cable. This is especially important

for cables including a large number of optical fibers. If the fibers are arranged in a

suitable geometry it may be possible to use multiple jointing techniques rather than

jointing each fiber individually.

8. JOINT OF FIBER:-

Optical fiber links, in common with any line communication system, have a requirement

for both jointing and termination of the transmission medium. The number of

intermediate fiber connections or joints is dependent upon the link length, the continuous

length of the fiber cable that may be produced by the preparation methods and the length

of the fiber cable that may be practically installed as a continuous section on the link.

It is therefore apparent that fiber to fiber connection with low loss and minimum

distortion (i.e. modal noise) remains an important aspect of optical fiber communication

system.

Before optical fibers splicing and joining are done certain preparations are made with

fiber or fiber cables as case may be to achieve best results at the end surface. First of all

the protective plastic that covers the glass cladding is stripped from each fiber end, which

is then cleaved with a special tool, producing a smooth and flat end.

1. Fiber splices: these are semipermanent or permanent joints which find major use in

most optical fiber telecommunication system (analogous to electrical soldered joints).

2. Demountable fiber connectors or simple connectors: these are removable joints which

allow easy, fast, manual coupling and uncoupling of fibers (analogous to electrical

plugs and sockets).

The above fiber to fiber joints are designed ideally to couple all the light propagating in

one fiber into the adjoining fiber. By contrast fiber couplers are branching devices that

split all the light from main fiber into two or more fibers or, alternatively, couple a

proportion of the light propagating in the main fiber into main fiber.

9. FIBER SPLICES:-

A permanent joint formed between two individual optical fibers in the field or factory is

known as a fiber splice. Fiber splicing is frequently used to establish long haul optical

fiber links where smaller fiber lengths need to be joined, and there is no requirement for

repeated connection and disconnection. Splices may be divided into two broad categories

depending upon the splicing technique utilized. These are fusion splicing or welding and

mechanical splicing.

Fusion splicing is accomplished by applying localized heating(e.g. by a flame or an

electric are ) at the interface between two butted, prealigned fiber ends causing them to

soften and fuse. Mechanical splicing, in which the fibers are held in alignment by some

mechanical means, may be achieved by various methods including the use of tubes

around the fiber ends (groove splices).

A requirement with fibers intended for splicing is that they have smooth and square end

faces. In general this end preparation may be achieved using a suitable tool which cleaves

the fiber as illustrated.

10. FUSION SPLICES:-

The fusion splicing – of single fibers involves the heating of the two prepared fiber ends

to their fusing point with the application of sufficient axial pressure between the two

optical fibers. It is therefore essential that the stripped (of cabling and buffer coating)

fiber ends are adequately positioned and aligned in order to achieve good continuity of

the transmission medium at the junction point. Hence the fiber are usually positioned and

clamped with the aid of an inspection microscope

.

Flame heating sources such as micro plasma torches (argon and hydrogen) and oxhydric

microburners (oxygen, hydrogen and alcohol vapour) have been utilized with some

success. However, the most widely used heating source is an electric arc. This technique

offers advantages of consistent, easily controlled heat with adaptability for use under

field conditions. A schematic diagram of the basic two fibers are welded together. Shows

a development of the basic are fusion process which involves the rounding of the fiber

ends with a low energy discharge before pressing the fibers together and fusing with a

stronger arc. This technique, known as perfusion, removes the requirement for fiber end

preparation which has a distinct advantage in the field environment.

A possible drawback with fusion splicing is that the heat necessary to fuse the fibers may

weaken the fiber in the vicinity of the splice. It has been found that even with careful

handling; the tensile strength of the fused fiber may be as low as 30 % of that of the

uncoated fiber before fusion.

11. EQUIPMENT REQUIRED FOR OFC JOINT:

1) Optical fiber fusion splicer specification ( spicer machine )

• AC input – 100 to 240v, frequency – 50/60Hz

• DC input 12v/aA

2) Fiber cutter

• It converts irregular shaped fiber end into smooth & flat end.

3) Chemicals used in OFC joint

• HAXENE : To remove jelly from the fiber

• ACETONE : For cleaning the OFC

• ISO PROPENOT: For smoothness of optical glass.

4) Sleeve: - To enclose fiber joint.

5) Tool Kit

6) Joint kit.

• Joint encloser

• Buffer

• Adhesive tap.

7) Generator /12V Battery

8) Cotton clothes for fiber cleaning.

12. ELECTRIC-FIELD WITH IN FIBER CLADDING:-

One other significant point should be noted from the electromagnetic field model. The model

predicts that the EM field does not suddenly drop to zero at the core-cladding boundary – it

instead decays as negative exponential within the cladding as shown in the figure 6.

This is

crucial for various technologies relating to fibers.

Figure 6 - The Electric Field within the Fiber Cladding

This method of signal transmission has benefits in terms of security – for the signal to be

‘tapped’ the fiber must be broken (since effectively no energy escapes from the fiber) and this

can easily be detected (when no signal reaches the other end of the fiber!).

This is one of the

many advantages of the medium. But mainly two factors, attenuation and dispersion of light,

have to be considered while transmitting the light over large distances.

We use repeaters and regenerators to reduce the attenuation and dispersion.

13. REPEATERS AND REGENERATORS:-

Optical repeaters are purely optical devices that are used simply to combat attenuation in the

fiber; typically spans of 80km upwards are now possible. The recent introduction of soliton

transmission methods has increased the allowed distance between repeaters and systems

spanning 130km without a repeater are now possible.

Regenerators are devices consisting of

both electronic and optical components to provide ‘3R’ regeneration – Retiming, Reshaping,

Regeneration. Retiming and reshaping detect the digital signal that will be distorted and noisy

(partly due to the optical repeaters), and recreate it as a clean signal as shown in figure 6 This

clean signal is then regenerated (optically amplified) to be sent on. It should be noted that

repeaters are purely optical devices whereas regenerators require optical-to-electrical (O/E)

conversion and electrical-to-optical (E/O) conversion.

The ultimate aim of many fiber system researchers is to create a purely

optical network without electronics, which would maximize efficiency and performance.

Many aspects of such a system are in place, but some still require the O/E and E/O

conversion.

Figure7 - A digital signal before (noisy and attenuated) and after regeneration

The most common optical amplifier currently in use is the EDFA (Erbium Doped Fiber

Amplifier). These consist of a coil of fiber doped with the rare earth metal erbium. A laser

diode pumps the erbium atoms to a high-energy state; when the signal reaches the doped fiber

the energy of the erbium atoms is transferred to the signal, thus amplifying it.

14. Light Sources:-

Two types of light source are used with fibers, LEDs and Laser Diodes. LEDs can operate in

the near infrared (the main wavelengths used in fibers are 1300nm and 1550nm, along with

850nm for some applications); they can emit light at 850nm and 1300nm. They also have the

advantages of long lifetimes and being cheap. Unfortunately they are large compared to the

cross-section of a fiber and so a large amount of light is lost in the coupling of an LED with a

fiber. This also reduces the amount of modal control designers have over incident light. Laser

diodes can be made to emit light at either 1300nm or 1550 nm, and also over a small spectral

width (unlike LEDs), which reduces chromatic dispersion. Their emitting areas are extremely

small and so the angle of incidence of light on a fiber can be accurately controlled such that

<5% of the possible modes within a multimode fiber will be initially used. They are more

efficient than LEDs in terms of coupling of light into the fiber, although they have shorter

lifetimes than and are more expensive than LEDs.

One crucial advantage of lasers over LEDs in today’s world of digital communications is

their high switching speed and small rise times, leading to increased bandwidth.

15. Detecting the Signal:-

The most efficient detectors are reverse-bias photo detectors. They essentially cause a current

to flow when light is incident on them. The choice of semiconductor that is used to fabricate

the detector is dependent on the wavelength sensitivity and the responsivity that are required.

Bandwidth considerations are also important (determined by the rise time and fall time of a

detector); in detectors the fall time is often appreciably greater than the rise time and so this

must be used to calculate the bandwidth of a detector.

There are many further complications in detectors, including noise equivalent power that

indicates how ‘clean’ a signal from a detector is. An analysis of how analogue and digital

signals are processed after the initial detector is also interesting.

16. ADVANTAGES OVER CONVENTIONAL CABLES:-

a. Wide Bandwidth:

Optical fibers offer greater bandwidth due to the use of light as carrier. The frequency range

used for glass fiber communication extends from 2*e14Hz to 4*e14Hz. Hence optical fibers

are suitable for high speed, large capacity telecommunication lines.

b. Low Loss:

In a coaxial cable attenuation increases with frequency. The higher the frequency of

information signals the greater the loss, whereas in an optical fiber the attenuation is

independent of frequency. They offer a loss of0.2 dBm/km, allowing repeater separation upto

50Km or more.

c. Freedom from electromagnetic interference:

Optical fibers are not affected by interference originating from power cables, railways and

radio waves. They do not limit unwanted radiation and no cross talk between fibers exists.

These fibers make an ideal transmission medium when EMI (Electro Magnetic Immunity) is

increased.

d. Non conductivity:

Optical fibers are non-conductive and are not effective by strong electromagnetic

interference such as lighting. These are usable in explosive environment.

e. Small diameters and less weight:

Even multi fiber optical cables have a small diameter and are light weight, and flexible

optical fiber cables permit effective utilization of speech and can also be applicable to long

distance use are easier to handle and install than conventional cables.

f. Security:

Fiber optic is a highly source transmission medium. It does not radiate energy that can be

received by a nearby antenna, and it is extremely difficult to tap a fiber and virtually

impossible to make the tap undetected.

g. Safety:

Fibre is a dielectric and does not carry electricity. It presents no sparks or fire hazards. It

does not cause explosions, which occur due to faulty copper cable.

17. APPLICATION OF THE OPTICAL FIBER COMMUNICATION:- TRUNK NETWORK

The trunk or toll network is used for carrying telephone traffic between major

conurbations. Hence there is generally a requirement for the use of transmission systems

which have a high capacity in order to minimize costs per circuit. The transmission

distance for trunk systems can very enormously from under 20 km to over 300 km, and

occasionally to as much as 1000 km. Therefore transmission systems which exhibit low

attenuation and hence give a maximum distance of unrepeatered operation are the most

economically viable. In this context optical fiber systems with their increased bandwidth

and repeater spacing offer a distinct advantage.

JUNCTION NETWORK:

The junction or interoffice network usually consists of routes within major conurbations

over distances of typically 5 to 20 km. However, the distribution of distances between

switching centers (telephone exchanges ) or offices in the junction network of large urban

areas varies considerably for various countries.

MILITARY APPLICATION:

In these applications, although economics are important, there are usually other, possibly

overriding, considerations such as size, weight, deployability, survivability (in both

conventional and nuclear attack and security. The special attributes of optical fiber

communication system therefore often lend themselves to military use.

MOBILES:

One of the most promising areas of milita5ry application for optical fiber communication

is within military mobiles such as aircraft, ships and tanks. The small size and weight of

optical fibers provide and attractive solution to space problems in these mobiles which

are increasingly equipped with sophisticated electronics. Also the wideband nature of

optical fiber transmission will allow the multiplexing of a number of signals on to a

common bus.

Furthermore, the immunity of optical transmission to electromagnetic

interference (EMI) in the often noisy environment of military mobiles is a tremendous

advantage. This also applies to the immunity of optical fiber to lighting and

electromagnetic pulses (EMP) especially within avionics. The electrical isolation, and

therefore safety, aspect of optical fiber communication also proves invaluable in these

applications, allowing routing through both fuel tanks and magazines.

COMMUNICATION LINKS:

The other major area for the application of optical fiber communication in the military

sphere includes both short and long distance communication links. Short distance optical

fiber systems may be utilized to connect closely spaced items of electronics equipment in

such areas as operations rooms and computer installations. A large number of this system

have already been installed in military installations in the united kingdom. These operate

over distances from several centimeters to a few hundred meters at transmission rates

between 50 bauds and 4.8 kbits-1. In addition a small number of 7 MHz video links

operating over distances of up to 10 m are in operation. There is also a requirement for

long distance communication between military installations which could benefit from the

use of optical fibers. In both these advantages may be gained in terms of bandwidth,

security and immunity to electrical interference and earth loop problems over

conventional copper systems.

CIVIL APPLICATION:

The introduction of optical fiber communication systems into the public network has

stimulated investigation and application of these transmission techniques by public utility

organizations which provide their own communication facilities over moderately long

distances. For example these transmission techniques may be utilized on the railways and

along pipe and electrical power lines.

In these applications, although high capacity transmission is not usually required, optical

fibers may provide a relatively low cost solution, also giving enhanced protection in harsh

environment, especially in relation to EMI and EMP. Experimental optical fiber

communication systems have been investigated within a number of organizations in Europe,

North America and Japan. For instance, British Rail has successfully demonstrated a 2 Mbits-

1 system suspended between the electrical power line gantries over a 6 km route in Cheshire.

Also, the major electric power companies have shown a great deal of interest with regard

to the incorporation of optical fibers within the metallic earth of overhead electric power

lines. fibers are now the standard.

TELECOMMUNICATION:

Optical point to point cable link between telephone substations.

LOCAL AREA NETWORKS (LAN's):

Multimode fiber is commonly used as the "backbone" to carry signals between the hubs of

LAN's from where copper coaxial cable takes the data to the desktop. Fiber links to the

desktop, however, are also common.

CABLE TV:

As mentioned before domestic cable TV networks use optical fiber because of its very low

power consumption.

CCTV:

Closed circuit television security systems use optical fiber because of its inherent security, as

well as the other advantages mentioned above.

18. FEATURE:-

The fiber optics has become a preferred medium due to its some important features like:

• The bandwidth of the fiber and light beam is extremely wide. It is possible to handle

signals which turn on and off at gigabit per second rates (1 gigabit, gbit =1000

Mbitts).

• The fiber itself is very thin and not expensive. The thinness means that it is easy to

handle, and many fibers can be put in the trenches or narrow conduits.

• The light signa-l is absolutely immune to electrical noise from any sources. Even if

there are sources of electrical noise directly touching the cable, the electric fields of

the noise source cannot affect the light beam in the fiber.

• The signal in the cable is secure from unauthorized listeners. It is relatively hard to

tap into the cable without being noticed, and the entire light signal is confined within

the fiber. No light escapes to the outside where someone else could see it.

• Since there is no electricity or electrical energy in the fiber, it can be run in hazardous

atmospheres where the danger of explosion from spark may exist. Also, the fiber

itself is immune to many types of poisonous gases, chemicals, and water.

19. ESSENTIAL FEATURES OF AN OPTICAL FIBER:-

1. Optical fibers may be produced with good stable transmission characteristics in long

lengths at a minimum cost and with maximum reproducibility.

2. A range of optical fiber types with regard to size, refractive indices and index

profiles, operating wavelengths, materials etc. be available in order to fulfill many

different system applications.

3. The fibers may be converted into practical cables which can be handled in a similar

manner to conventional electrical transmission cables without problems associated

with the degradation of their characteristics or damage.

4. The fibers and fiber cables may be terminated and connected together without

excessive practical difficulties and in ways which limit the effect of this process on

the fiber transmission characteristics to keep them within acceptable operating levels.

It is important that these jointing techniques may be

applied with ease in the field location where cable connection takes place.

20. DRAWBACKS OF OPTICAL FIBER COMMUNICATION:-

The use of fibers for optical communication does have some drawbacks in practice.

Hence to provide a balance picture these disadvantages must be considered. They are

• The fragility of the bare fibers;

• The small size of fibers and cables which creates some difficulties with splicing andforming connectors;

• Some problems involved with forming low loss T- couplers;

• Some doubts in relations to the long term reliability of optical fibers in the presenceof moisture;

• An independent electrical power feed is required for any electronic repeaters;

• New equipment and field practice are required;

• Testing procedures tend to be more complex.

21. Conclusions:-

We are currently in the middle of a rapid increase in the demand for data bandwidth across

the Earth. For most applications optical fibers are the primary solution to this problem. They

have potentially a very high bandwidth, with many of the bandwidth limitations now being at

the transceivers rather than being an intrinsic property of the fiber allowing easy upgrading of

systems without relaying cable.

This is creating a surge in the deployment of fiber both in

backbones of networks and in topologically horizontal cabling, which inturn is supporting

and propelling the industry into further research. With the adoption of new techniques such as

DWDM, soliton transmission, and ultimately the purely optical network, we have a medium

that will satisfy our communication needs for the foreseeable future.

22. Bibliography:- Optical Fibers And Sources For Communications

---Adams and Henning,

Principles Of Modern Optical Systems

--- Andonovic and Uttamchandani

An Introduction to Optical Waveguides

---Adams, M. J.