Upload
doankhue
View
221
Download
3
Embed Size (px)
Citation preview
IMPORTANT: If installing a Telescopic Pivot Door only; ie. a recess installation, please refer to alternative fixing details on the document reverse.
IN00272 (rev B)
Telescopic Pivot Door & Side PanelInstruction suitable for both Right and Left Hand fixing variations.•
Help Line: 0870 241 6131
Check that the tray has been installed correctly • and that it is level (Fig. A), tiled down onto and sealed to the manufacturer’s guidelines. Please Note: All product supplied without tray.Ensure the product is fitted to a non-porous • surface ie. tiled. Check that the wall surface is flat.Unpack and check the product is complete and • undamaged.Fixings are supplied for solid walls only. Ensure • that the correct fixings are used for the wall type – if in doubt seek professional advice.Ensure the area is clean, dry and dust free.• Read the instructions in full.• Have the correct tools available, (as shown • below, see ‘Tools Required’).It is recommended to situate the showerhead • and door adjacent to each other in order to allow any water spray to be on the side panel or upstanding wall.
Handle all glass with care - support on cardboard to avoid risk of breakage.• This product is heavy and requires 2 people to carry and install it.• When drilling walls check first for hidden pipes and cables.• All glass is toughened – it cannot be reworked or replaced by ordinary glass.• Use safety eyewear when drilling.• Use safety eyewear when handling glass.• Keep all small parts away from children.•
Safety
Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held • responsible for any installation costs that may arise from damaged or faulty product being installed.Please dispose of all packaging with due regard to the environment.•
Disclaimer
Before You Start
Tools Required (not supplied)
Fig.A.
Spirit Level Screwdriver Tape Measure
Junior Hacksaw
Pencil Utility Knife
Silicone Gun & Sealant Power Drill Suitable Drill Bits
6mm dia. *
3mm dia. HSS
* Ensure drill bit used is suitable for wall surface
Lines open: 8.30am - 5.00pm Monday to FridayStandard National call charge rate from BT landlines
Side PanelX1
Telescopic Pivot Door
X1
Short Horizontal Door SealX1
Horizontal Door Seal
X1
Parts & Fittings Supplied
Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from a damaged or faulty product being installed.
!Keep small parts away from children!
D1
D2
D3
D4
B
D
C
Wall Channel X2
Door Handle Assembly
X1
A
D
D
C
E
D2D1
D4D3
No.8 x 1¾” Pan Head Pozi Screws (actual size)
(actual size)
(actual size)
(actual size)
Ax6
Qty
Wall PlugsBx6
Qty
No.8 x ⅜” Pan Head Pozi ScrewsCx9
Qty
Screw Snap CapDx15
Qty
(actual size)
Ex4
Qty
Loose Screws & Fittings Supplied
A
A
1
Position Wall Channel onto Side Panel, DO NOT FIX at this stage.!
Position Side Panel and mark as shown. Ensure Side Panel is level.!
Make a note of Dimension A (from Wall Channel to edge of Tray).!
Ensure glass is positioned straight and is parallel with tray. !Mark Side Panel positions as shown.!
Plan View
AA
B*
8-15mm**A
* Dimension B = Telescopic Door width
** 8-15mm to be left for adjustment
Position Wall Channel onto Telescopic Pivot Door, DO NOT FIX at this stage.
!
2 Position Telescopic Pivot Door and mark as shown. Ensure Telescopic Pivot Door is level.
!
Plan ViewIMPORTANT NOTE:Ensure that Wall Channel is positioned to match dimension A, as taken in previous step (1).
!
Mark Telescopic Pivot Door position as shown.!
Ensure glass is positioned straight and is parallel with tray. !
3
3.1
6mm dia. holes with drill bit suitable for wall surface
Mark position of pre-drilled Wall Channel fixing hole
A
3.2
3.3B
D
Fix through pre-drilled Wall Channel fixing hole
Wall plugs supplied are for solid walls only. Ensure correct wall plug for wall type is used. If in doubt seek professional advice.
!Position Wall Channel on wall as shown, ensure Wall Channel is fixed level. !
Tip: When drilling tiles apply masking tape to surface to stop drill bit slipping.*
Inside View
E
4.3*4.4
* 3mm dia. holes through pre-drilled holes using HSS drill bit
4.2
4.1
Mark adjustment position.
Adjust Telescopic Pivot Door to match dimension B,
(as taken in step 2).
4
Ensure same dimension (B) at the top and bottom of Telescopic Pivot Door.!Take Care to ensure that Telescopic pivot Door is fixed straight and not twisted.!
5.1
! INSIDE
Please Note: Ensure deflector faces inwards.
5.2
5.3 Plan View
Ensure glass is positioned straight and is parallel with tray. !
Push fit Horizontal Seals.!
7
* 3mm dia. holes through pre-drilled holes using HSS drill bit
*3mm dia. holes through pre-drilled holes using
HSS drill bit
C
D
Inside ViewInside View
C
6.1*
6.2
Tip: When inserting screws apply a small amount of oil to the screw thread to allow easier fixing.
* Ensure glass is positioned straight and is parallel with tray. !
D
Tip: When inserting screws apply a small amount of oil to the screw thread to allow easier fixing.
*Ensure glass is positioned straight and is parallel with tray. !
Inside ViewInside View
7.1*
7.2
6
8.1
8
Please Note: Door Handles are supplied assembled. Using Allen key supplied, disassemble part and then re-assemble as shown. Ensure all screw heads are on the enclosure interior. DO NOT overtighten.
!
Inside View
150mm
150mm
150mm
Apply Silicone Sealant, (not supplied).!Only apply silicone sealant to the outside of the enclosure. DO NOT use silicone sealant on inside of the enclosure.
!Product Care: Use a non-abrasive cleaner. Water marks may be removed with a proprietary limescale remover or household vinegar.
*
9
IMPORTANT: If installing a Telescopic Pivot Door and Side Panel; ie. a corner installation, please refer to alternative fixing details on the document reverse.
IN00272 (rev B)
Telescopic Pivot DoorInstruction suitable for both Right and Left Hand fixing variations.•
Help Line: 0870 241 6131
Check that the tray has been installed correctly • and that it is level (Fig. A), tiled down onto and sealed to the manufacturer’s guidelines. Please Note: All product supplied without tray.Ensure the product is fitted to a non-porous • surface ie. tiled. Check that the wall surface is flat.Unpack and check the product is complete and • undamaged.Fixings are supplied for solid walls only. Ensure • that the correct fixings are used for the wall type – if in doubt seek professional advice.Ensure the area is clean, dry and dust free.• Read the instructions in full.• Have the correct tools available, (as shown • below, see ‘Tools Required’).It is recommended to situate the showerhead • and door adjacent to each other in order to allow any water spray to be on the side panel or upstanding wall.
Handle all glass with care - support on cardboard to avoid risk of breakage.• This product is heavy and requires 2 people to carry and install it.• When drilling walls check first for hidden pipes and cables.• All glass is toughened – it cannot be reworked or replaced by ordinary glass.• Use safety eyewear when drilling.• Use safety eyewear when handling glass.• Keep all small parts away from children.•
Safety
Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held • responsible for any installation costs that may arise from damaged or faulty product being installed.Please dispose of all packaging with due regard to the environment.•
Disclaimer
Before You Start
Tools Required (not supplied)
Fig.A.
Spirit Level Screwdriver Tape Measure
Junior Hacksaw
Pencil Utility Knife
Silicone Gun & Sealant Power Drill Suitable Drill Bits
6mm dia. *
3mm dia. HSS
* Ensure drill bit used is suitable for wall surface
Lines open: 8.30am - 5.00pm Monday to FridayStandard National call charge rate from BT landlines
Short Horizontal Door Seal
X1
Horizontal Door Seal
X1
Telescopic Pivot Door
X1
Parts & Fittings Supplied
Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from a damaged or faulty product being installed.
!Keep small parts away from children!
D3
D1
D2
Door Handle Assembly
X1
B
D
A
Wall Channel X2
C
D
E
D2D1
D3
No.8 x 1¾” Pan Head Pozi Screws (actual size)
(actual size)
(actual size)
(actual size)
Ax6
Qty
Wall PlugsBx6
Qty
No.8 x ⅜” Pan Head Pozi ScrewsCx6
Qty
Screw Snap CapDx12
Qty
(actual size)
Ex4
Qty
Dimension A* - (minus) 20mm = Telescopic Pivot Door Width (B)
*Between walls, recess dimension.
1Make a note of Dimension A* (from recess opening).!
Loose Screws & Fittings Supplied
***Telescopic Pivot Door width: Refer to Step 1 for details.
E
2.3*2.4
* 3mm dia. holes through pre-drilled holes using HSS drill bit
2.2
2.1
Mark adjustment position.
Adjust Telescopic Pivot Door to match dimension B,
(as taken in step 1).
2
Ensure same dimension (A) at the top and bottom of Telescopic Pivot Door.!Take Care to ensure that Telescopic pivot Door is fixed straight and not twisted.!
! INSIDE
Please Note: Ensure deflector faces inwards.
Please Note: Position one wall channel and mark. Ensure Wall Channel is level and in correct location to the tray. (If in doubt refer to illustration on step 2).
!3.1
3.2
3.3 3.4
IMPORTANT: Ensure Door is not twisted. For best results fix one side wall channel, and check door is level before continuing to fix second wall channel.
!
Position Wall Channel on wall as shown, ensure Wall Channel is fixed level. !Wall plugs supplied are for solid walls only. Ensure correct wall plug for wall type is used. If in doubt seek professional advice.
!Tip: When drilling tiles apply masking tape to surface to stop drill bit slipping.*
4.1
6mm dia. holes with drill bit suitable for wall surface
Mark position of pre-drilled Wall Channel fixing hole
4.2
4.3
4
Fix through pre-drilled Wall Channel fixing hole
A
B
D
Ensure glass is positioned straight and is parallel with tray. ! Inside View
Plan View
6
5*3mm dia. holes through pre-drilled holes using
HSS drill bit
C
D
Tip: When inserting screws apply a small amount of oil to the screw thread to allow easier fixing.
*
Inside ViewInside View
5.1*
5.2
6.1
Please Note: Door Handles are supplied assembled. Using Allen key supplied, disassemble part and then re-assemble as shown. Ensure all screw heads are on the enclosure interior. DO NOT overtighten.
!
Inside View
150mm
7
Apply Silicone Sealant, (not supplied).!Only apply silicone sealant to the outside of the enclosure. DO NOT use silicone sealant on inside of the enclosure.
!Product Care: Use a non-abrasive cleaner. Water marks may be removed with a proprietary limescale remover or household vinegar.
*
Notes:Notes: