In A Single Direction - Eclipse Architectural · 2019-08-22 · to build an Eclipse folding door system. ECE3DJ Eclipse E3 Drilling Jig See E3 Drilling Jig instruction sheet on (under

© Copyright 2019 Eclipse Architectural® FULL SCALE EXCEPT AS NOTED© Copyright 2019 Eclipse Architectural®

The Eclipse E3™ is a premier folding door system for larger folding doors. It has been designed for strength and is generously proportioned to meet the requirements of specifiers looking for folding solutions in medium to large residential and commercial applications. Stainless steel bearings in the pivots and carriers allow even the largest doors to be moved quietly and with fingertip ease between the open and closed positions.

In A Single Directionmax panel weight: 250lbs (115kg)

max panel width: 48” (1200mm)

max panel height: 144” (3600mm)

max number of panels: 8 each way

panel thickness when using E3 sill system: 1-3/4” (44.5mm) or 2-1/4” (57mm)

panel thickness when using floor channel: 1-3/8” (34.9mm) to 3” (76.2mm)

NOTE: When using maximum panel width & height 48” (1200mm) x 144” (3600mm) panel may exceed maximum panel weight of 250 lbs (115 kg). Calculated weight check should be done.

E3™ System For Exterior Folding Doors

© Copyright 2019 Eclipse Architectural® FULL SCALE EXCEPT AS NOTED

E3

© Copyright 2019 Eclipse Architectural® ALL DRAWINGS NO SCALE

Parts Selection

Top track with flushbolt pin channel

Weatherseals & Astragal

Sill SystemFloor Channel

Flushbolts or Twinpoint

Eclipse E3 is specified with 5 separate groups: track, sill, weathersealing, flushbolts and hardware. Components are required from all 5 groups to build an Eclipse folding door system.

ECE3DJEclipse E3 Drilling JigSee E3 Drilling Jig instruction sheet on www.eclipsearchitectural.com (under Products > E3 folding door systems)

EC190 Fir astragal, may be stained or painted

ECP108-35BL Pile weatherseal for door with astragal, 5/16” (8mm) pile height, black

EC7145-270BL Pile weatherseal for EC70 & EC75 top track, black

EC421 Kerf seal

EC369A7145BL Aluminum T-slot extrusion with black pile insert, for bottom of doors

EC415BL black weatherseal for between doors, use on clad doors where kerf slot is not possible

KT75C clear anodizedKT75D bronze anodizedLengths available: 111”, 147”, 183”, 222”, 294” (2819mm, 3734mm, 4648mm, 5639mm, 7467mm)

4 flushbolt lengths available:

1” (25.4mm) throw length regardless of bolt length. Finishes available: brushed aluminum or bronze powder coat.

EC23DV floor channel, bronze anodized with PVC insert, black.Lengths available: 111”, 147”, 183”, 222”, 294” (2819mm, 3734mm, 4648mm, 5639mm, 7467mm)

EC23BLVE Replacement PVC insert (only)

KT795 8” wide (203mm) for 1-3/4” (44.5mm) door.KT797 8” wide (203mm) for 2-1/4” (57mm) door. KT775 6-9/16” wide (167mm) for 1-3/4” (44.5mm) door. KT777 6-9/16” wide (167mm) for 2-1/4” (57mm) door.

KT749 Flushbolt cup, satin or bronze

KT750GASKET included with EC749, fits under rim of cup

Hardware

2 stock finishes available: Stainless steel & pvd bronze

1-31/32” (50mm)

3-37/64” (90.9mm)

NEWPRODUCT

7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)

1" (25.4mm)

KT768GASKET sill to jamb assembly gasket

Fir top water return sill, extruded aluminum clear or bronze anodized.

KT795COVERBLVEPVC insert, black. Snap in cover for flushbolt channels for the new Eclipse sill & top track. Fits into sills above.

PVD brass (TG) finish is custom order, call for manufacturing time.

for outswing & inswing doors

Flushbolt cup used with floor channel and ADA sill

Lengths available: 111”, 147”, 183”, 222”, 294” (2819mm, 3754mm, 4648mm, 5639mm, 7468mm). Order flushbolt cups and sill assembly end gaskets separately.

E3 SYSTEM COMPONENTS

Top Track, extruded aluminum (optional)

KT70D bronze anodized. Length available: 147” (3734mm)

2-7/16” (62mm)

2” (50.2mm)

EC421 Weatherseal for sill, jamb and header. Black, brown or white

EC417 Weatherseal for between doors. Black or brown

© Copyright 2019 Eclipse Architectural® FULL SCALE EXCEPT AS NOTED© Copyright 2019 Eclipse Architectural®ALL DRAWINGS NO SCALE

E3

2-7/16” (62mm)

2” (50.2mm)

neopreneblackgasket

1-17/32” (39mm)to face of door

5/16” (8mm)from center of

top track to face of door

centre of track tocentre of channel23/32” (18.5mm)

3/8” (9.5mm) panelclearance to sill

7/8” (22mm)

15/16”(24mm)

19/32” (15mm)

3/16” (5mm)panel clearance

to head

EXTERIOR INTERIOR

KTE3HGASKETAdhesive blackgasket for optimum sealing performance around all hinge flaps.

2-3/8” (60mm) bottom of door to bottom of hinge flap when using flush bolts.

5-29/32” (150mm) when using twinpoint lock.

top of doorto top of hinge

flap 19/32” (15mm)

2-3/8” (60mm) top of door to top of hinge flap when using flush bolts.

5-29/32” (150mm) when using twinpoint lock.

ARCHITECTURAL DETAIL

��

panel width

panel thickness

half offsethinges

outswingpanels

5/8” (16mm)

4 one way configuration

19/32” (15mm)hinge offset

panel offset19/32” (15mm)

5-1/2” (139.7mm)

1-5/16” (33.5mm)

Centre of top track to centre of bottom channel 23/32” (18.5mm)

EXTERIOR INTERIOR

KT795 sill

KT75 top track

KT70 top track


flushbolt machiningcentered at stile width

RO.5 (R1/64)

pivot door

weathersealapplication

11/16”(17.5mm)

11/16”(17.5mm)

1/8”(3.2mm)

3/8”(9.5mm)

1/8” (2.5mm) 9/16” (14mm)

5/32” (4mm)

ECP108-35BL

EC417

3/8”(9.5mm)

1/8”(3.5mm)

6-9/16”(166.7mm)

5/16”(7.4mm)

9/32”(7mm)

3/4” (18.5mm)5/16” (7.4mm)

5/16” (7.4mm)

5/16”(7.4mm)

1/8” (2.8mm)

1-3/4”(44.5mm)

1-7/16” (36mm)9/16” (14mm)

4-3/8”(110.6mm)

39/64”(15.4mm)

1-5/8”(41mm)

CL

CL

CLREF

REF

latching door to jamb, weatherseal & strike plate application for 3L, 3R, 5L, 5R,

7L or 7R.

KT745 extended strike plate for 1-3/4” (44.45mm) door thickness only. Used with standard style lock set.

EC421

4-5/16”(107mm)

E3


ARCHITECTURAL DETAIL

EC417 & ECP108-35BL Weatherseal Detail for 1-3/4” (44.5mm) Door

4L (4 doors folding left) exterior view (all doors are same width)

4-5/16”(110mm)

4”(107mm)

Extended strike plate for 1-3/4” door only.Used with standardstyle lock set.

KT745ESPXSatin finish

KT745ESPQBronze powder coat

9/32”(7mm)

5/32” (4mm)

5/16” (8mm)

5/32” (4mm)

9/32”(7mm)

When using 1-3/4” (44.5mm) or 2-1/4” (57mm) panel thickness on 2L2R or 4L4R configurations, the gapping between the 2 meeting panels should be 5/16” (8mm). Hinge flaps on the meeting stiles should be machined into the edge of the door.

Over Camming

optional weatherseals for meeting stiles

EXTERIOR

INTERIOR right carrier set

hinge set (flat)

pivot setwall

pivot set

pivot setwall pivot sethinge set (flat)

flushbolts flushbolts

left carrier set

jamb clearance9/32” (7mm)

jamb clearance9/32” (7mm)

panel to panel gap5/32” (4mm)


W W W W




E3

© Copyright 2019 Eclipse Architectural®

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

� ��

��

��

��

HARDWARE LIST FOR DOOR CONFIGURATIONS Passage set/lock, flushbolt, astragal & hardware placement for outswing applicationsFrom Left To Right

Configuration is always determined when viewing system from exterior side, going from left to right.

Use “D” pull handle on exit door (outswing system) where passage set / lock not required. Use flushbolts top and bottom to lock door from the inside only. NOTE: exit door not accessible from exterior.

INTERIOR

EXTERIOR

OUTSWING

INSWING

INTERIOR

EXTERIOR

3L

3LI

How To Determine Swing Of Systems

FB FB3L INTERIOR

EXTERIOR

outswing application “D” pull handle option

Use one “D” pull handle on each pair of inswing doors to pull open and close doors.Inswing application “D” pull handle option

FB FB5RI

INTERIOR

EXTERIOR

E3

© Copyright 2019 Eclipse Architectural®

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

� ��

��

��

��

��

��

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

HARDWARE LIST FOR DOOR CONFIGURATIONS Passage set/lock, flushbolt, astragal & hardware placement for outswing applications

From Left To Right

intermediate carrier & guide set left carrier & guide setINTERIOR

EXTERIOR

pivot set

flushbolts flushbolts

half offset hinge set flat hinge setpassage set

pivot set

jamb doorjamb doorbasic door

leading door

service door

door hold

Hardware Application 3L2R

© Copyright 2019 Eclipse Architectural®FULL SCALE EXCEPT AS NOTED © Copyright 2019 Eclipse Architectural® FULL SCALE EXCEPT AS NOTED

E3

19/3

2”

(15m

m)

vinyl

chan

nel

inse

rt1-

3/16

”(3

0mm

)

wee

p ho

le

wee

p ho

les

2-5/

32”

(54m

m)

1-23

/32”

(44m

m)

FIR

OR O

AK T

OP

WOO

D SU

BSTR

ATE

13/3

2” (1

0mm

)

6-9/

16”

(166

.7mm

) ja

mb

line

8” (2

03m

m)

1/4”

(6m

m)E3

bot

tom

hi

nge

& gu

ide

6-9/

16” (

166.7

mm

) ja

mb

line

KT79

5COV

ERBL

VE

PVC

inse

rt, b

lack

2-1

/4” (

57m

m)

KT79

7 Si

ll

3/8”

(9

.5mm

)

EC42

1 Ke

rf se

al

EC36

9A71

45BL

Alum

inum

T-slo

t ex

trusio

n w

ith g

ray

pile

inse

rt

cent

re o

f top

trac

k to

cen

tre o

f bo

ttom

cha

nnel

=

23/3

2” (1

8.5m

m)

KT797 (8") OUTSWING SILL SYSTEM FOR 2-1/4" (57MM) DOOR THICKNESS

New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural.Extrusion Alloy 6063 T5. Actual full sill width: 8" (203mm) channel sill for flushbolt or twinpoint

KT797E3FIRC Clear anodizedKT797E3FIRD Bronze anodized

EC78

0SPC

Prot

ectiv

e vi

nyl s

ill c

over

for s

ill n

ose

EC75

0SPC

Prot

ectiv

e vi

nyl s

ill c

over

for i

nter

ior f

ir to

p

EXTE

RIORFlus

hbol

t

Two

lock

ing

optio

ns: Tw

inpo

int

NO

SCAL

E


E3

New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural.

KT795 (8”) OUTSWING SILL SYSTEM FOR 1-3/4” (44.5MM) DOOR THICKNESSExtrusion Alloy 6063 T5. Actual full sill width: 8” (203mm) channel sill for flushbolt or twinpoint

19/3

2”

(15m

m)

vinyl

chan

nel in

sert

1-3/

16”

(30m

m)

wee

p ho

le

wee

p ho

les

2-5/

32”

(54m

m)

2-7/

32” (

57m

m)

WOO

D SU

BSTR

ATE

3/8”

(9

.5mm

)

1-3/

4” (4

4.5m

m)

13/3

2” (1

0mm

)

8” (2

03m

m)

1/4”

(6m

m)E3

bot

tom

hi

nge

& gu

ide

6-9/

16” (

166.7

mm

) ja

mb

line

EC42

1 Ke

rf se

al

KT84

1Re

duce

r

KT79

5 Si

ll

KT79

5COV

ERBL

VE

PVC

inse

rt, b

lack

6-9/

16”

(166

.7mm

) ja

mb

line

cent

re o

f top

trac

k to

cen

tre o

f bo

ttom

cha

nnel

=

23/3

2” (1

8.5m

m)

EC36

9A71

45BL

Alum

inum

T-slo

t ex

trusio

n w

ith g

ray

pile

inse

rt

FIR

OR O

AK T

OP


EC78

0SPC

Prot

ectiv

e vi

nyl s

ill c

over

for s

ill n

ose

EC77

0SPC

Prot

ectiv

e vi

nyl s

ill c

over

for i

nter

ior f

ir to

p

EXTE

RIOR

Flus

hbol

t

Two

lock

ing

optio

ns: Tw

inpo

int

NO

SCAL

E


E3

1-3/

16”

(30m

m)

6-9/

16” (

167m

m)

6-9/

16” (

166.7

mm

) ja

mb

line

19/3

2”

(15m

m)

13/3

2”(1

0mm

)1/

4” (6

mm

)

vinyl

chan

nel

inse

rt

wee

p ho

les

wee

p ho

le

2-1

/4” (

57m

m)

1-23

/32”

(44m

m)

2-5/

32”

(54m

m)

WOO

D SU

BSTR

ATE

KT77

7 Si

ll

3/8”

(9

.5mm

)

EC42

1 Ke

rf se

al

KT79

5COV

ERBL

VE

PVC

inse

rt, b

lack

6-9/

16”

(166

.7mm

) ja

mb

line

E3 b

otto

m

hing

e &

guid

e

cent

re o

f top

trac

k to

cen

tre o

f bo

ttom

cha

nnel

=

23/3

2” (1

8.5m

m)

EC36

9A71

45BL

Alum

inum

T-slo

t ex

trusio

n w

ith g

ray

pile

inse

rt

FIR

OR O

AK T

OP

New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural.

Extrusion alloy 6063 T5. Actual full sill width: 6-9/16” (166.7mm) channel sill for flushbolt or twinpoint

KT777 (6-9/16”) OUTSWING SILL SYSTEM FOR 2-1/4” DOOR THICKNESS


KT75

0SPC

Prot

ectiv

e vi

nyl s

ill c

over

for i

nter

ior f

ir to

pKT

760S

PCPr

otec

tive

viny

l sill

cov

er fo

r sill

nos

e

EXTE

RIOR

Flus

hbol

t

Two

lock

ing

optio

ns: Tw

inpo

int

NO

SCAL

E


E3

1-3/

16”

(30m

m)

6-9/

16” (

167m

m)

6-9/

16” (

166.7

mm

) ja

mb

line

19/3

2”

(15m

m)

13/3

2” (1

0mm

)1/

4” (6

mm

)

vinyl

chan

nel

inse

rt

wee

p ho

les

2-5/

32”

(54m

m)

WOO

D SU

BSTR

ATE

1-3/

4” (4

4.5m

m)

2-7/

32” (

57m

m)

KT77

5 Si

ll

KT84

1Re

duce

r

3/8”

(9

.5mm

)

EC42

1 Ke

rf se

al

KT79

5COV

ERBL

VE

PVC

inse

rt, b

lack

6-9/

16”

(166

.7mm

) ja

mb

line

wee

p ho

le

E3 b

otto

m

hing

e &

guid

e

cent

re o

f top

trac

k to

cen

tre o

f bo

ttom

cha

nnel

=

23/3

2” (1

8.5m

m)

EC36

9A71

45BL

Alum

inum

T-slo

t ex

trusio

n w

ith g

ray

pile

inse

rt

FIR

OR O

AK T

OP

New generation sill with flushbolt pin channel. Sill is fabricated as shown by Eclipse Architectural.Extrusion Alloy 6063 T5. Actual full sill width: 6-9/16” (166.7mm) channel sill for flushbolt or twinpoint

KT775 (6-9/16”) OUTSWING SILL SYSTEM FOR 1-3/4” DOOR THICKNESS


KT77

0SPC

Prot

ectiv

e vi

nyl s

ill c

over

for i

nter

ior f

ir to

pKT

760S

PCPr

otec

tive

viny

l sill

cov

er fo

r sill

nos

e

EXTE

RIOR

Flus

hbol

t

Two

lock

ing

optio

ns: Tw

inpo

int

NO

SCAL

E


E3

5/16

”(8

mm

)

19/6

4”(7

.5mm

)

11/1

6”(1

7.5m

m)

1/8”

(3m

m)

1/8”

(3m

m)

11/1

6”(1

7.5m

m)

9/16

”(1

5mm

)

1-3/

32”

(28m

m)

3/8”

(9.5m

m)

4-27

/32”

(123

mm

)

6-9/

16”

(167

mm

)

CL

9/32

”(7

mm

)

7/64

”(2

.5mm

) 3/32

” (2.

38m

m)EC

417

kerf

seal

inse

rt

9/16

”(1

4mm

)1-

7/16

” (36

mm

)

Flush

bolt

mac

hini

ng d

epth

:1)

KTD

BSY

9/16

” (14

mm

)2)

KTD

BOC

43/6

4” (1

7mm

)3)

KTD

BOE

43/

64” (

17m

m)

4) K

TDBO

T 3/

4” (1

9mm

)

1/4”

(6.35

mm

)

2-1/

4”(5

7mm

)

EC42

1ke

rf se

alin

sert

R =

1/64

” (0

.5mm

)

Drop

bolt

mac

hini

ng

cent

ered

at s

tile

wid

th w

ith

dedi

cate

d ro

uter

bits

.

NO S

CALE

9/32

”(7

mm

)M

ultip

oint

face

pla

te

notc

hre

quire

din

jam

b

ECP1

08-3

5BL

pile

wea

ther

sesa

l

5/32

”(4

mm

)

EC42

1ke

rf se

alin

sert

REF

exte

rior

4-5/

16”

(110

mm

)

4”(1

07m

m)Ex

tend

ed S

trike

Pla

te

KT74

5ESP

XSa

tin fi

nish

KT74

5ESP

QBr

onze

pow

der c

oat

for 1

-3/4

” doo

r onl

y. Us

ed w

ith st

anda

rdst

yle lo

ck se

t.NO

SCA

LE

E3™ JAMB FOR 2-1/4” (57MM) DOOR THICKNESSExterior E3 Folding Door, Outswing Application

Actu

al m

achi

ning

for f

lush

bolts

(fac

e pl

ate)

1-27/

64” x

7-7/

8” (3

6mm

x 2

00m

m)

1-27/

64” x

15-3

/4” (

36m

m x

400

mm

)1-2

7/64

” x 2

3-5/

8” (3

6mm

x 6

00m

m)

1-27/

64” x

39-

3/8”

(36m

m x

1000

mm

)

DBOT FlushboltTwo locking options:

TwinpointEC

E2DB

FORB

Flu

shbo

lt ro

uter

bit

is av

aila

ble


E3

11/1

6”(1

7.5m

m)

1/8”

(3m

m)

1/8”

(3m

m)

11/1

6”(1

7.5m

m)

9/16

”(1

5mm

)

1-5/

8”(4

1mm

)

3/8”

(9.5m

m)

4-3/

8”(1

10.6m

m)

6-9/

16”

(167

mm

)

EC42

1ke

rf se

alin

sert

CL

CL

CL

REF

exte

rior9/

32”

(7m

m)

9/32

”(7

mm

)

Drop

bolt

mac

hini

ng

cent

ered

at s

tile

wid

th w

ith

dedi

cate

d ro

uter

bits

.

7/64

”(2

.5mm

)

R =

1/64

” (0

.5mm

)

7/64

” (2.

8mm

)

EC41

7 ke

rf se

al in

sert

9/16

”(1

4mm

)1-

7/16

” (36

mm

)

23/3

2” (1

8.5m

m)

Flush

bolt

mac

hini

ng d

epth

:1)

KTD

BSY

9/16

” (14

mm

)2)

KTD

BOC

43/6

4” (1

7mm

)3)

KTD

BOE

43/

64” (

17m

m)

4) K

TDBO

T 3/

4” (1

9mm

)

1/4”

(6.35

mm

)5/

16”

(8m

m)

19/6

4”(7

.5mm

)

1-3/

4”(4

4.5m

m)

notc

hre

quire

din

jam

b

5/32

”(4

mm

)

EC42

1ke

rf se

alin

sert EC

P108

-35B

Lpi

le w

eath

erse

sal

Mul

tipoi

ntfa

ce p

late

NO S

CALE

4-5/

16”

(110

mm

)

4”(1

07m

m)Ex

tend

ed S

trike

Pla

te

KT74

5ESP

XSa

tin fi

nish

KT74

5ESP

QBr

onze

pow

der c

oat

for 1

-3/4

” doo

r onl

y. Us

ed w

ith st

anda

rdst

yle lo

ck se

t.NO

SCA

LE

E3™ JAMB FOR 1-3/4” (44.5MM) DOOR THICKNESSExterior E3 Folding Door, Outswing Application.

Actu

al m

achi

ning

for f

lush

bolts

(fac

e pl

ate)

1-27/

64” x

7-7/

8” (3

6mm

x 2

00m

m)

1-27/

64” x

15-3

/4” (

36m

m x

400

mm

)1-2

7/64

” x 2

3-5/

8” (3

6mm

x 6

00m

m)

1-27/

64” x

39-

3/8”

(36m

m x

1000

mm

)DBOT FlushboltTwo locking options:

Twinpoint

ECE2

DBFO

RB F

lush

bolt

rout

er b

it is

avai

labl

e


E3

KT75 TOP TRACK FOR 2-1/4” (57MM) DOOR THICKNESS E3™ HEADERExterior E3 folding door, EC75 Outswing application only. Channel top track for flushbolt or twinpoint

New Generation Top Track with Flushbolt Pin Channel.

2-21

/32”

(6

8mm

)

3/16

” (5m

m)

19/3

2”

(15m

m)

E3 b

otto

m

hing

e &

guid

e

6-9/

16”

(166

.7mm

) ja

mb

line

11/1

6”

(18m

m)

1-31

/32”

(5

0mm

)

1/8”

(3m

m)

3/16

” (5m

m)

11/1

6”(1

8mm

)

19/3

2”

(15m

m)

6-9/

16”

(166

.7mm

) ja

mb

line

3/8”

(9.5m

m)

19/3

2”

(15m

m)

1-1/

8” (2

8mm

)

EC42

1Ke

rf se

al

KT79

5COV

ERBL

VEPV

C in

sert,

bla

ckEC

7145

-270

BLPi

le w

eath

erse

al, b

lack

1/2”

(1

2.7m

m)

6-9/

16” (

167m

m)

5-7/

8” (1

50m

m)

1-13

/16”

(46m

m)

11/1

6”

(17m

m)

KT75

top

track

KT75C ClearKT75D Bronze anodized

EXTE

RIOR

Flus

hbol

tTw

o lo

ckin

g op

tions

:Tw

inpo

int


E3

KT75 TOP TRACK FOR 1-3/4” (44.5MM) DOOR THICKNESS E3™ HEADERExterior E3 folding door, EC75 Outswing application only. Channel top track for flushbolt or twinpoint.

New Generation Top Track with Flushbolt Pin Channel. 6-

9/16

” (16

7mm

)5-

7/8”

(150

mm

)

11/1

6”

(18m

m)

1-31

/32”

(5

0mm

)

1/8”

(3m

m)

1/8”

(3m

m)

3/8”

(9.5m

m)

11/3

2” (9

mm

)

1-5/

8” (4

1mm

)

3/16

” (5m

m)

11/1

6”(1

8mm

)

1/2”

(1

2.7m

m)

11/1

6”

(17m

m)

2-21

/32”

(6

8mm

)

3/16

” (5m

m)

19/3

2”

(15m

m)

6-9/

16”

(166

.7mm

) ja

mb

line

19/3

2”(1

5mm

)

6-9/

16”

(166

.7mm

) ja

mb

line

E3 b

otto

m

hing

e &

guid

e

EC42

1Ke

rf se

al

KT79

5COV

ERBL

VEPV

C in

sert,

bla

ck

EC71

45-2

70BL

Pile

wea

ther

seal

, bl

ack

1-13

/16”

(46m

m)

KT75

top

track

KT75C Clear anodizedKT75D Bronze anodized

EXTE

RIOR

Flus

hbol

tTw

o lo

ckin

g op

tions

:Tw

inpo

int


E3

KT218 FLOOR CHANNEL

2-1/8” (54mm)

1-3/16”(29.6mm)

2-1/8” (54mm)

hardwood or title hardwood or title1/2”(12.7mm)

thickness of finished floor willdetermine blockout depth

KT218DV Aluminum bronze anodized with3 pvc inserts, black

1/2”(12.7mm) hardwood or title hardwood or title

thickness of finished floor willdetermine blockout depth

13/32” (10mm)

1-3/4” (44.45 mm)

1/4” (6mm)

EXTERIOR INTERIOR

KT795COVERBLVEincluded

EC23BLVE


E3

KT218 FLOOR CHANNEL

finished concrete floor2-1/8” (54mm)

1-3/16”(29.6mm)

13/32” (10mm)

2-1/4” (57mm)

1/4” (6mm)

Floor channel for E2 & E3 Systems Only

EC23DV Floor channel, bronze anodized with PVC insert, black

EC23BLVE PVC insert only, black (replacement part)Lengths available: 111”, 147”, 183”, 222”, 294” (2.81m, 3.73m, 4.64m, 5.63m, 7.46m)

EXTERIOR INTERIOR

EXTERIOR INTERIOR

EC369A7145BLdual door

bottom pile seals

15/16”(24mm)

EC23DVfloor channel with PVC insert

min door thickness when usingfloor channel is 1-3/8” (35mm)

2-1/4” (57mm)

KT749Flush bolt cup

KT749Flush bolt cup

7/8"(22mm)

7/8"(22mm)

15/16”(24mm)

13/32”(10mm)

13/32”(10mm)

3/16”(4.6mm)

7/8”(22mm)

7/16”(11mm)

1-3/4” (44.5mm)

finished floor line

finished floor line

1/2”(12.7mm)

7/8”(22mm)7/16”

(11mm)

EC23

NO SCALE

NO SCALE

EXTERIOR INTERIOR

© Copyright 2019 Eclipse Architectural®FULL SCALE EXCEPT AS NOTED

E3

KT752 SERIES E3™ 5-1/2” (139.7MM) OUTSWING SILL SYSTEMOnly For 1-3/4” (44.5mm) Door Thickness & 4-9/16” (115.8 mm) Wall Thickness

NOTE: Door height plus 4-1/4”: (107.9mm) = R.O. (from finished floor line to R.O. header) when using Eclipse frame specs.

KT788 E3 ADA LOWRISE ALUMINUM SILL FOR INSWING & OUTSWING DOORS

KT788E3D Bronze anodized only

KT752E3FIRD Outswing sill with fir top, bronze anodized only

ADA Compliant

EXTERIOR

2-1/8” (54mm)

INTERIOR

substrate

1-3/16” (30mm)

interior fir topmouldEC421 sill weatherseal

white, brown or black

5-1/2” (140 mm)

KT752 E3 aluminum sill, clear or bronze anodized

EXTERIOR

weep hole

weep holes

bottom rollerguide channel

vinyl channel insert

channel for flushbolt pin

1-1/16”(27mm)

KT760SPCProtective vinyl sill cover for sill nose

NO SCALEUse KTDBSY series flush bolt

23/32”(18.5mm)

6-9/16” (166.7mm)

1/2”(12.7mm)15/16” (23.6mm)

finished floor line

19/32”(15mm)

KTDBSY Flush bolt

KT749 flush bolt cup used,custom drilling required in sill

thermal break

1-3/4” (44.45mm)

23/32”(18.5mm)

6-9/16” (166.7mm)

1/2”(12.7mm)

15/16”(23.6mm)

19/32”(15mm)

1-3/4”(44.45mm)

NO SCALE

drill round hole for pin

no flush bolt cup used

finished floor line

NO SCALE

Slopes of threshold may be ripped off to achieve flush sill application.

© Copyright 2019 Eclipse Architectural® NO SCALE

E3

SURELOCK 5 UPGRADE

JAMB TO SILL ASSEMBLY

screws

jamb

fir top moulding

inserts snap into channel

E3 sill extruded aluminum clear or bronze anodized, with wood substrate and interior top moulding (fir)

EC421 kerf seal

EC421kerf seal

KT768GASKET sill to jamb assembly gasket

EC23BLVEPVC insert, black

KT795COVERBLVEPVC insert, black

NO SCALE

The new Surelock 5 technology ensures folding doors running on E2 and E3 hardware can be adjusted simply with an Allen key. Offering seven upgrades from the original version, the new Surelock 5:

1. Ensures adjustment is self-evident with insertion of an 5/16” (8mm) Allen key into the end of the pin – now you can explain adjustment over the phone to your customers.

2. Removes the problematic yellow shipping clip found at the bottom of the pin – it can’t be left in place after adjustment is finalized at installation.

3. Use of the Allen key provides more torque, so the panel no longer needs to be ‘unweighted’ during adjustment.

4. Eliminates the locking wafer which had possibility of shif ting off-center and scratching the panel during adjustment.

5. Allows for one-handed adjustment with the Allen key. 6. Allows you to use an extended Allen key to adjust the door from ground level

– a ladder or stool is no longer required making it safer for employees. 7. Looks great thanks to the simplified design of the pin.

The E3 hardware now accommodates:Max. panel weight 250lbs (115kg)Max. panel height 144” (3600mm)Max. panel width 48” (1200mm)

Cycle tested to the equivalent of opening and closing the door every day for 40 years!

1 2 3


E3

KT779D E3™ SILL SYSTEM FOR 2-1/4” (57MM) DOOR THICKNESSWater Return All Aluminum Sill System, Thermally Broken For INSWING FOLDING DOORS (Only EC70 Top Track can only be used on inswing application)

10˚ slope

6-9/16” (166.7mm)

2-7/16” (62mm) 11/16”(17.5mm)

11/16”(17.5mm)

2-11/16”(67.7mm)

3/8”(9mm)

2”(50.2mm)

11/16”(17.5mm)

1/4”(6mm)

3/8”(9.5mm) striker plate

Use KTDBOE Series flush bolt

flushbolt pin

KT70 E3aluminum top track

EC421 kerf seal insert

3/8” (9.5mm)

4-7/8” (123.2mm)

7/16” (10.5mm)

23/32” (18.5mm) center line of top trackto center line of bottom sill channel

2-1/4” (57mm)3-15/16” (99.8mm)

5/16”(8mm)

3/16” (5mm)

1-1/8” (28mm)

EC369

3/8" (9.5mm)

11/16"(18mm)

2-1/16” (53.1mm)

1-11/16” (43.5mm)

7/16"(10.8mm)

3/16”(4mm)

1/4” (7mm)2-1/8"

(54mm)

6-9/16” (166.7mm)I-Strut Thermal break

PVC channel filler

1” (25.7mm)


(CL) (CL)

1-29/32” (48.4mm)

EXTERIOR INTERIOR

weephole

weephole

weephole

KT779D Sill

weephole

1/8”(3.17mm)

bronze anodized only

Use KTDBOC Series flush bolt

KTDBSPOC Protective strike plate

EC7145-270BLPile weatherseal, black

BRONZE ANODIZED ONLY

INSWING DOORS


E3

10˚ slope

6-9/16” (166.7mm)

2-7/16” (62mm) 11/16”(17.5mm)

11/16”(17.5mm)

2-11/16”(67.7mm)

3/8”(9mm)

2”(50.2mm)

11/16”(17.5mm)

1/4”(6mm)

3/8”(9.5mm) striker plate


flushbolt pin



3/8” (9.5mm)

4-7/8” (123.2mm)

7/16” (10.5mm)


2-1/4” (57mm)3-15/16” (99.8mm)

5/16”(8mm)

3/16” (5mm)

1-1/8” (28mm)

EC369

3/8" (9.5mm)

11/16"(18mm)

2-1/16” (53.1mm)

1-11/16” (43.5mm)

7/16"(10.8mm)

3/16”(4mm)

1/4” (7mm)2-1/8"

(54mm)


PVC channel filler

1” (25.7mm)


(CL) (CL)

1-29/32” (48.4mm)

EXTERIOR INTERIOR

weephole

weephole

weephole

KT779D Sill

weephole

1/8”(3.17mm)

bronze anodized only



EC7145-270BLPile weatherseal, black

6-9/16” (166.7mm)

2-11/16”(67.7mm)

11/16”(17.5mm)

2”(50.2mm)

3/8”(9mm)

1/4”(6mm)

3/8”(9.5mm)

1/8” (3.17mm)11/16”

(17.5mm)

center line (CL)of top track

(CL)(CL)

striker plate

flushbolt pin


2-7/16” (62mm) 11/16”(17.5mm)

3/16” (5mm)

1-29/32” (48.4mm)

5/16”(8mm)

4-3/8” (110.6mm)

3/8” (9.5mm)

1-5/8” (40.7mm)

7/16” (10.5mm)3-15/16” (99.8mm)

EXTERIOR INTERIOR


PVC channel filler

1” (25.7mm)KT769D Sill

weephole

weephole

weephole

weephole


1/4”(7mm)

3/16”(4mm)

EC369


9/16"(14.3mm)

7/16"(10.8mm)

10˚ slope

2-1/8" (54mm)

3/8" (9.5mm)

2-3/8 (56.2mm)

1-3/4” (44.5mm)2-9/16” (65mm)


Bronze anodized only



EC7145-270BLpile weatherseal, black


KT769D E3™ SILL SYSTEM FOR 1-3/4” (44.5MM) DOOR THICKNESSWater Return All Aluminum Sill System, Thermally Broken For INSWING FOLDING DOORS (Only EC70 Top Track can only be used on inswing application)

BRONZE ANODIZED ONLY

INSWING DOORS

© Copyright 2019 Eclipse Architectural®NO SCALE

E3

E3 PARTS SELECTIONWhen ordering, add color designation (letters) to end of product number: OL: pvd bronze | S: stainless steel | TG: pvd brass

KTE3CPS Pivot sets2 pieces

KTE3EH Interior D pull handlefor inswing doors1 piece

Intermediate carrier sets with additional hinge

KTE3CLCS Left carrier sets2 pieces

KTE3HNHS Hinge sets (FLAT) without middle handle for inswing doors - 3 pieces

Hinge sets no handle for inswing doors

KTE3CRCS Right carrier sets2 pieces

KTE3HHS Half OFFSET hinge sets with middle handle for outswing doors - 3 pieces

Half offset hinge sets with handle for outswing doors

KTE3CICS Intermediate carrier sets, 3 pieces

KTE3HHNHS Half offset hinge sets without middle handle for inswing doors - 3 pieces

Half offset hinge sets no handle for inswing doors

KTE3WPS Wall pivot set, jamb mounted middle pivot for doors over 88” (2235mm)1 piece

ECE3HS Hinge sets (FLAT) with middle handle for outswing doors - 3 pieces

Hinge sets with handle for outswing doors

ECE3CBPIVOTH bottom pivot housing only (replacement part)

concealed bottom guide




KTE3HNHSingle hinge, order separately


KTE3HHNHSingle hinge, order separately


KTE3HHNHSingle hinge, order separately

mounted betweentop & bottompivot

PVD brass (TG) finish is custom order, call for manufacturing time.

© Copyright 2019 Eclipse Architectural® NO SCALE

E3

Number of Hinges for Panel Heights of 80” to 118” (2032mm to 2997mm)

Intermediatecarrier sets

Hinge set or half offset hinge set

Pivot set top & bottom

Up to 96” (2438mm)door height use1, 3, 5

Up to 96” (2438mm)door height use1, 3, 5

Up to 87-15/16” (2234mm)door height use 1 & 5

108-1/16 ” to 118” (2745 to 2997mm)door height use 1, 2, 3, 4, 5

#1 #1

#2 #2

#3 #3

#4 #4

#5 #5

#1

#2

#3

#4

#5

96-1/16” to 108”(2440 to 2743mm)use 1, 2, 3, 5

96-1/16” to 108”(2440 to 2743mm)use 1, 2, 3, 5

88” to 96” (2235 to 2438mm)door height use 1, 3, 5

108-1/16 ” to 118”(2745 to 2997mm)use 1, 2, 3, 4, 5

108-1/16 ” to 118”(2745 to 2997mm)use 1, 2, 3, 4, 5

96-1/16” to 108” (2440 to 2743mm)door height use 1, 2, 3, 5

Pivot Set

Wall Pivot Set Use with above pivot set on doors over 8ft (2438mm) in height

Half Offset Hinge SetMiddle hinge with handle for outswing doors

Hinge Set (Flat)Middle hinge with handle for outswing doors

Intermediate Carrier Set

Right Carrier Set

Left Carrier Set

Single Hinge Half OffsetNo handle for inswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height.

Single Hinge (Flat) No handle for inswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height.

Half Offset Hinge SetNo middle handle for inswing doors

Hinge Set (Flat)No middle handle for inswing doors

Single Hinge Half OffsetWith handle for outswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height

Single Hinge (Flat)With handle for outswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height

2 pieces

1 piece

3 pieces

3 pieces

3 pieces

2 pieces

2 pieces

1 piece

1 piece

3 pieces

3 pieces

1 piece

1 piece

KTE3CPSTG PVD brass KTE3CPSOL PVD bronzeKTE3CPSS stainless steel

KTE3SCREWTG PVD brass KTE3SCREWOL PVD bronzeKTSCREWSS stainless steel

KTE3WPSTG PVD brass KTE3WPSOL PVD bronzeKTE3WPSS stainless steel

KTE3HHSTG PVD brass KTE3HHSOL PVD bronzeKTE3HHSS stainless steel

KTE3HSTG PVD brass KTE3HSOL PVD bronzeKTE3HSS stainless steel

KTE3CICSTG PVD brass KTE3CICSOL PVD bronzeKTE3CICSS stainless steel

KTE3CRCSTG PVD brass KTE3CRCSOL PVD bronzeKTE3CRCSS stainless steel

KTE3CLCSTG PVD brass KTE3CLCSOL PVD bronzeKTE3CLCSS stainless steel

KTE3HHNHTG PVD brass KTE3HHNHOL PVD bronzeKTE3HHNHS stainless steel

KTE3HNHTG PVD brass KTE3HNHOL PVD bronzeKTE3HNHS stainless steel

KTE3HHNHSTG PVD brass KTE3HHNHSOL PVD bronzeKTE3HHNHSS stainless steel

KTE3HNHSTG PVD brass KTE3HNHSOL PVD bronzeKTE3HNHSS stainless steel

KTE3HHTG PVD brass KTE3HHOL PVD bronzeKTE3HHS stainless steel

KTE3HTG PVD brass KTE3HOL PVD bronzeKTE3HS stainless steel

E3 PARTS SELECTION

Replacement Screws for all hingesPVD brass (TG) finish is custom order, call for manufacturing time.


FLUSHBOLTS

FLUSHBOLTS FOR OUTSWING FOLDING DOORS: DBOT SERIES

SELECT FINISH PRODUCT NUMBER DESCRIPTION

bronze powder coat finish on aluminum

KTDBOT200NRQ 8" (200mm) 1” throw, round endKTDBOT400NRQ 16" (400mm) 1” throw, round endKTDBOT600NRQ 24" (600mm) 1” throw, round endKTDBOT1000NRQ 39" (1000mm) 1” throw, round end

brushed metallic finish on aluminum to match stainless steel

KTDBOT200NRX 8" (200mm) 1” throw, round endKTDBOT400NRX 16" (400mm) 1” throw, round endKTDBOT600NRX 24" (600mm) 1” throw, round endKTDBOT1000NRX 39" (1000mm) 1” throw, round end

bright gold finishon aluminum

KTDBOT200NRTG 8" (200mm) 1” throw, round endKTDBOT400NRTG 16" (400mm) 1” throw, round endKTDBOT600NRTG 24" (600mm) 1” throw, round end

Max wind load: 450kg (990lb) forceMin door thickness: 1-3/4” (44.5mm)Throw length: 1” (25mm)Finishes: Bronze powder coat on aluminum to match pvd bronze finish on E3 hinges. Brushed metallic on aluminum to match stainless steel finish on E3 hinges. Bright gold (TG) finish on aluminum to match pvd brass finish on E3 hinges.

The flush-mounted flushbolts, rounded style and 1” (25mm) throw are designed for use with sliding and folding doors. This flushbolt will resist high winds and is rated to resist a 250kg load in Western Red Cedar and 450kg in Amoora. The bolts are easily installed with a dedicated router bit and are available in three finishes.

PLEASE NOTE: Flushbolt housing & slide bar are manufactured from aluminum components

1” (25mm) throw length regardless of bolt length

INTERIOR

Architectural Detail

2-7/16” (62mm)

13/16” (20.6mm)

7/8”(22mm)

KTE2DBFORB Router bit for flushbolts (dedicated router bits are available)

Bright gold (TG) finish is custom order, call for manufacturing time.

flushbolt machining centered at stile width

R = 1/64” (0.5mm)9/16” (14mm)

CL

1-27/64” (36mm)

1/8”(2.5mm)

3/4”(19mm)

KT749 Flushbolt cup used with floor channel and ADA sill

Flushbolt cup used with floor channel and ADA sillKT749BRONZE bronze powder coatKT749DCH Satin chrome


Strike plate for headerKTDBSPQ bronze powder coat KTDBSPS Satin chrome

7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)

1-27/64”(36mm)

43/64” (17mm)

35/64” (14mm)

47/64” (18.6mm)

pin diameter 25/64” (10mm)

35/64” (14mm)

1” (25mm)

Flushbolt Assembly

Actual machining for flushbolts (face plate)1-27/64” x 7-7/8” (36mm x 200mm) 1-27/64” x 23-5/8” (36mm x 600mm)1-27/64” x 15-3/4” (36mm x 400mm) 1-27/64” x 39-3/8” (36mm x 1000mm)


FLUSHBOLTS

SELECT FINISH PRODUCT NUMBER DESCRIPTION

powder coat finishbronze overaluminum

KTDBSY200NRQ 8” (200mm) 1” throw, round endKTDBSY400NRQ 16” (400mm) 1” throw, round endKTDBSY600NRQ 24” (600mm) 1” throw, round endKTDBSY1000NRQ 39” (1000mm) 1” throw, round end

brushed metallic finish over aluminum to match stainless steel

KTDBSY200NRX 8” (200mm) 1” throw, round endKTDBSY400NRX 16” (400mm) 1” throw, round endKTDBSY600NRX 24” (600mm) 1” throw, round endKTDBSY1000NRX 39” (1000mm) 1” throw, round end

bright gold finishover aluminum

KTDBSY200NRTG 8” (200mm), 1” throw, round endKTDBSY400NRTG 16” (400mm) 1” throw, round endKTDBSY600NRTG 24” (600mm) 1” throw, round end

Max wind load: 450kg (990lb) forceMin door thickness: 1-3/4” (44.5mm)Bolt lengths: 8”, 16”, 24”, 39” (200mm, 400mm, 600mm, 1000mm)Finishes: Bright gold to match pvd brass hardware bronze powder coat on aluminum to match the pvd bronze hardware & brushed metallic to match stainless steel hardware

INTERIOR

Architectural Detail Flushbolt Assembly (Machining Spec)

2-7/16” (62mm)

13/16” (20.6mm)

7/8”(22mm)

flushbolt machining centered at stile width

R = 1/64” (0.5mm)9/16” (14mm)

CL

1-27/64” (36mm)

1/8”(2.5mm)

3/4”(19mm)

KT749 Flushbolt cup used with floor channel and ADA sill


KTE2DBFORB Router bit for flushbolts (dedicated router bits are available)

Flushbolt cup used with floor channel and ADA sillKT749BRONZE bronze powder coatKT749DCH Satin chrome


7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)

1-31/32”(50mm)

1-27/64”(36mm)

17/32”(13mm)

pin diameter9/16 (14mm)

1” (25mm)

The flush-mounted flushbolts, rounded style and 1” (25mm) throw are designed for use with sliding and folding doors. Symphony™ will resist high winds and is rated to resist a 250kg load in Western Red Cedar and 450kg in Amoora. The bolts are easily installed with a dedicated router bit and are available in three finishes.

Symphony™

FLUSHBOLTS FOR OUTSWING FOLDING DOORS: DBSY SERIES

Bright gold ( TG) finish is custom order, call for manufacturing time.

Actual machining for flushbolts (face plate)1-27/64” x 7-7/8” (36mm x 200mm) 1-27/64” x 23-5/8” (36mm x 600mm)1-27/64” x 15-3/4” (36mm x 400mm) 1-27/64” x 39-3/8” (36mm x 1000mm)

© Copyright 2019 Eclipse Architectural®ALL DRAWINGS NO SCALE

bronze powder coat finish over aluminum

KTDBOC200NRQ 8" (200mm) concealed 3/4” FB, throwKTDBOE200NRQ 8" (200mm) 1” throw, round endKTDBOE400NRQ 16" (400mm) 1” throw, round endKTDBOE600NRQ 24" (600mm) 1” throw, round endKTDBOE1000NRQ 39" (1000mm) 1” throw, round end

brushed metallic finish over aluminum to match stainless steel

KTDBOC200NRX 8" (200mm) concealed FB, 3/4” throwKTDBOE200NRX 8" (200mm) 1” throw, round endKTDBOE400NRX 16" (400mm) 1” throw, round endKTDBOE600NRX 24" (600mm) 1” throw, round endKTDBOE1000NRX 39" (1000mm) 1” throw, round end

bright gold finish over aluminum

KTDBOC200NRTG 8" (200mm) concealed FB, 3/4” throwKTDBOE200NRTG 8" (200mm) 1” throw, round endKTDBOE400NRTG 16" (400mm) 1” throw, round endKTDBOE600NRTG 24" (600mm) 1” throw, round endKTDBOE1000NRTG 39" (1000mm) 1” throw, round end

FLUSHBOLTS FOR INSWING FOLDING DOORS: DBOE & DBOC SERIESMinimum door thickness: 1-3/4” (44.5mm)DBOC Throw length: 3/4” (20mm) • DBOE Throw length: 1” (25mm) Finishes: Bronze powder coat on aluminum to match pvd bronze finish on E3 hinges. Brushed metallic on aluminum to match stainless steel finish on E3 hinges. Bright gold (TG) finish on aluminum to match pvd brass finish on E3 hinges.

Actual machining for flushbolts (face plate)1-27/64” x 7-7/8” (36mm x 200mm)1-27/64” x 15-3/4” (36mm x 400mm)1-27/64” x 23-5/8” (36mm x 600mm)1-27/64” x 39-3/8” (36mm x 1000mm)


1-5/16” (33.3mm) face of door to center of pin

1" (25mm)

further machining required for inswing flush bolts offset pins

Flushbolt pin drops into bottom channel or into E3 inswing sill channel.

E3 floor channel

3/4" (20mm)

further machining required for larger bottom pin

KTDBOETop flushbolt

EXTERIOR INTERIOR

1-3/4’’ (45mm) min thickness

KTDBOCBottom flushbolt

KT70Top track

4 lengths available:

KTE2DBFORB Router bit for flushbolts

fit striker to pin side of drop bolt (opposite the black plastic cap)

KTDBPCS Replacement end cap for OC flushbolt pin

Replacement strike plate for OC flushbolt KTDBSPOCX Brushed finishKTDBSPOCQ Bronze powder coat

fit centrally to the drop bolt when in the closed position


PRODUCT CODE DESCRIPTION

OC flushbolt for bottom of doors

OE flushbolt for top of doors



Router bit for flushboltsKTE2DBFORB

7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)

STRIKER FOR INSWING DOORS

FLUSHBOLTS


E4 SILL WITH TWO LOCKING OPTIONSDBSY Flushbolt for 1-3/4” or 2-1/4” door thickness

DBSY Series Flushbolt

Twinpoint (2-1/4” door thickness only)

Twinpoint

E4 Sill E4 Sill

KT80E4 track / header

KT80E4 track / header

E3 SILLS WITH TWO LOCKING OPTIONS

Flushbolt

For 1-3/4” (44.5mm) or 2-1/4” (57mm) Door Thickness

KT795 Sill

Channel for 1-3/4” (44.5mm) door

Channel for 2-1/4” (57mm) door

snap in covers for channels

NO SCALENO SCALE

Twinpoint

KT775 Sill

DBOT Series Flushbolt

Twinpoint

LOCKING OPTIONS


LT2 Transmission Housingbrushed metallic aluminum or black anodized finish

Swing HandleDF3: Aluminum handle (4 finishes)DF4: Stainless Steel Handle (2 finishes)

Finishes & MaterialsThe Twinpoint door furniture is available in a range of finishes to suit any door or décor. Twinpoint Lock assembly not available in PVD Brass (TG)

ECLIPSE TWINPOINT LOCK & SWING HANDLE

Function

Style

Testing

The LT2 operates easily with a simple handle rotation, driving a 1” (25mm) throw into the head and sill. This makes it one of the most secure bolt locks on the market. An installed Twinpoint system is completely accessible and serviceable.For people with mobility impairments, the Twinpoint of fers the security of two flushbolts, but without the access problems associated with flushbolts being too high or low to reach, and hard-to-grip door handles.

LT2 has the sleek and clean styling synonymous with all Eclipse products. Their low profile allows any folding system, such as F3, E2, E3 or E4 to stack neatly, without intrusive door furniture getting in the way. Eclipse Twinpoint locks are fully concealed within the door stile, avoiding long or hard-to-reach dropbolts fixed to the door face, particularly on tall doors. The Eclipse Twinpoint is an unobtrusive, functional and sleek locking solution.

The Centor LT2 has been tested to 100,000 cycles at maximum configuration to ensure smooth working order beyond their 10 year warranty period. The LT2 Twinpoint locking system has also been exposed to dust, mud, sand and corrosive atmospheres to ensure they stand up to real life use. This includes exposure to salt spray for seaside installations.

Min door thickness: 1-3/8” (35 mm) / Min rod length: 15” (381 mm) / Throw length: 1” (25 mm) / Uses: folding, french & sliding

LT2 TwinPoint Housing Cover Plate Finishes

DF3 Twinpoint swing handle, 4 finishes over cast aluminum

brushed metallic aluminum

black anodized aluminum

satin aluminum powder coat

black powder coat

bronze powder coat

DF4 Twinpoint Swing Handle (SS)

brushed stainless steel

PLEASE NOTE: colors & finishes are indicative only.

pvd bronze over stainless steel

Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel.

twinpoint & swing handle



multipoint &lever lock set

4L 3L

TWINPOINT

PRODUCT # DESCRIPTION

EC TwinPoint Lock (LT2 model) for use with DF3 (aluminum) & DF4 (stainless steel) ModelsECLT2TRSN0924X TwinPoint transmission rod, cover plate and strike plate for 96” (2438mm) door height / brushed metallic aluminum finish

ECLT2TRSN0924Y TwinPoint transmission rod, cover plate and strike plate for 96” (2438mm) door height / black anodized finish

ECLT2TRSN0930X TwinPoint transmission rod, cover plate and strike plate for 120” (3048mm) door height / brushed metallic aluminum finish

ECLT2TRSN0930Y TwinPoint transmission rod, cover plate and strike plate for 120” (3048mm) door height / black anodized finish

EC Lock Gear Box for EC TwinPoint (LT2 model)ECLT2NS Lock/gear box for EC TwinPoint transmission rod, cover plate & handle

EC Swing Handle DF3 (aluminum) Model For EC TwinPoint (LT2 model)ECDF3SHNAL DF3 swing handle aluminum, black powder coat

ECDF3SHNAPCN DF3 swing handle aluminum, satin aluminum powder coat

ECDF3SHNAQ DF3 swing handle aluminum, bronze powder coat

EC Swing Handle DF4 (Stainless Steel) Model For EC TwinPoint (LT2 Model)ECDF4SHNSOL DF4 swing handle stainless steel, PVD bronze finish

ECDF4SHNSS DF4 swing handle stainless steel, brushed finish

Cup for Sill or Head (Mandatory for Sill, Optional for Head)ECLTBC8SS Brushed S.S. Finish

ECLTBC8SOL PVD Bronze Finish

TL2 Router BitECLT2RB Router bit for LT2 TwinPoint Lock Assembly

Eclipse E3 Drilling Jig for E3 Hinge placement on doorECE3DJ Eclipse E3 drilling jig for wood doors

Strike Plate for Head (For replacement purposes only) One strike supplied with Twinpoint (Standard)ECLTSP8SS Brushed S.S. Finish

ECLTSP8OL PVD Bronze Finish

LT2 TWINPOINT LOCK & DF3 (ALUMINUM) OR DF4 (STAINLESS STEEL) SWING HANDLESKit Components For Twinpoint Assembly

transmission rod

PLEASE NOTE:

When ordering complete TwinPoint Assembly, you are required to order: transmission rod & cover plate, lock/gear box, swing handle & cups.

Twinpoint Lock assembly not available in PVD Brass (TG)

transmission rod

swing handle assembly(6 finishes)

lock/gear box

two finishes available on outer housing cover plate


DF3 Twinpoint swing handle, 4 finishes over cast aluminum

TWINPOINT


LT2 TWINPOINT��

��

��

��

��

��

��

LT2 Model TwinPoint Lock

DF3 Model TwinPoint Swing Handle (Aluminum)orDF4 Model Twinpoint Swing Handle (Stainless Steel)

E3 Top Track

E3 floor channel used in conjunction with twinpoint

New E3 Sill used in conjuction with Twinpoint

Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel.

Twinpoint & Swing Handle



Multipoint &Lever Lock Set

4L 3L

TWINPOINT


5-7/8”(150mm)

5-7/8”(150mm)

5-7/8”(150mm)

5-7/8”(150mm)

7/16”(11mm)

5/16”(7.5mm)

CL

3/8”(9.9mm)

7-7/8” (199.65mm)

3/8”(9.9mm)

7-7/8” (199.65mm)

CL

3/8”(9.9mm)

7-7/8” (199.65mm)

CL

TWINPOINT LOCK FOR 2-1/4” PANEL ONLY AS SHOWN BELOW

DBOT FLUSHBOLT SHOWN WITH 2-1/4” PANEL

DBSY FLUSHBOLT SHOWN WITH 1-3/4” PANEL

E4 Track/ Header

E4 Track/ Header

E4 Track/ Header

E4 Sill used in conjunction with Twinpoint

E4 Sill used in conjunction with DBOT Series Flushbolt

E4 Sill used in conjunction with DBSY Series Flushbolt

hinge placement is higher on door than shown

hinge placement is higher on door than shown

hinge placement is lower on door than shown

hinge placement is lower on door than shown

Standard = 36” (914mm)

Minimum = 15” (381mm)

exterior side outswing panels



TWINPOINT


A

A

1-7/64” (28mm)

15/32” (12mm)

1-1/32”(26mm)

R7 9/32”(7.2mm)

3-3/16”(81mm)

4-61/64”(126mm)

13/64”(5mm)

WOOD STILE ROUTE PROFILE (OUTSWING APPLICATION) FOR LT2 MODEL

60.0°

9/32” (7.1mm)

5/64” (1.8mm)

Detail A

ECLT2RB Route stile

1-3/4” (44.5mm)

1-3/32”(27.80mm)

32/23”(18.4mm)

1/2”(12.7mm)

5/32”(4mm)

3/32”(2.5mm)

9/16”(14.4mm)

2-1/8”(54mm)

14-11/64”(360mm)

9-1/16” (230.2mm)

R 1/2”(12.7mm)

2-5/64” (53mm)

11/16” (18mm)

standard height9/14”

(36mm)

B

Detail A

Back Set

min 1-3/8” (35mm)

TWINPOINT

© Copyright 2019 Eclipse Architectural® ALL DRAWINGS NOS SCALE

1-11/16”(43mm)

R 13/32”(10.5mm)

13/16”(21mm)

11/64” (4.2mm)

21/64” (8.4mm)

1-3/4” (44.5mm)

19/64” (7.6mm)

E2 / E3 HINGE PLACEMENT OVER TWINPOINT

A A

5/32" (4mm)1-3/32" (27.8mm)

9/16"(14.4mm)

1-3/4" (44.5mm)

SECTION A-A

E2 Hinge

E3 hinge

Strike plate for head

Flushbolt cup used with floor channel

KTLTSP8SS Brushed s.s. finishKTLTSP8OL PVD bronze finish

KTLTBC8SS Brushed s.s. finishKTLTBC8SOL PVD bronze finish

2-13/32”(61mm)

TWINPOINT HINGE OFFSET THICKNESS OF DOOR PANEL PROGRAM

5/32” (4mm) 1-3/4” (44.45mm) E2, E3, F2, F3

7/16” (11mm) 2-1/4” (57.15mm) E4

TWINPOINT


EC23 OPTIONAL FLOOR CHANNEL APPLICATION FOR OUTSWING OR INSWING DOORS

This application is recommended for interior application, exterior non-rainfall weather conditions or undercover well protected doors.

EC23DV Floor channel, bronze anodized with PVC insert, blackEC23BLVE PVC insert only, black (replacement part)Lengths available: 111”, 147”, 183”, 222”, 294” (2.81m, 3.73m, 4.64m, 5.63m, 7.46m)

EXTERIOR INTERIOR

EXTERIOR INTERIOR

EC369A7145BLdual door

bottom pile seals

15/16”(24mm)

EC23DVfloor channel with PVC insert

min door thickness when usingfloor channel is 1-3/8” (35mm)

2-1/4” (57mm)

KT749Flush bolt cup

KT749Flush bolt cup

7/8"(22mm)

7/8"(22mm)

15/16”(24mm)

13/32”(10mm)

13/32”(10mm)

3/16”(4.6mm)

7/8”(22mm)

7/16”(11mm)

1-3/4” (44.5mm)

finished floor line

finished floor line

1/2”(12.7mm)

7/8”(22mm)7/16”

(11mm)

Door height plus 3-3/4” (95.3mm) = R.O. (from finished floor line)door height plus 3-1/4” (82.55mm) = full jamb height

FLOOR CHANNEL


Eclipse KT740 Door Hold For Exterior Folding Doors

DOOR HOLDS

The Eclipse Door Hold is used to secure or hold the active swing door and / or doors in place to prevent possible damage in the event of wind slamming one panel into the next panel.

PRODUCT # FINISH MATERIAL QUANTITY

KT740DHC Clear anodized Aluminum 1 per pack

KT740DHD Bronze anodized Aluminum 1 per pack

Installation InstructionsInstall unit as shown in picture, typically at the top of the door panels. Centre main unit on door stile, 1 to 2 inches (25 to 50mm) from the top edge of door. Fasten in place with 1-1/2” (38mm) screws supplied. Fold all door panels to one side or both sides (depending on configuration) and align the T-unit with slot into the main unit and fasten in place with 1-1/2” (38mm) screws supplied. Adjust tension screws accordingly and lock in place with set screws (1/8” allen key supplied). Make sure the adjustment tension screws are evenly balanced; this will ensure that the T-unit slides into the slot of the main unit evenly.

ECLIPSE DOOR HOLD

Stainless steel screws supplied with clear anodized unit.Stainless steel screws (bronze colored) supplied with bronze anodized unit.

T-Unit

set screenadjustment screw

main unit

KTDCAS Satin Aluminum Finish KTDCAOL Black Finish KTDCATG Brass Finish

Door Hold Magnets (optional) KTEMAG MagnetsFor holding the door panels in the open position

3L KTEMAG Sold as pairs

magnets

door hold

13/16” (20.6mm)

2-3/8” (60.3mm)

5L

DOOR HOLDS

© Copyright 2019 Eclipse Architectural®FULL SCALE EXCEPT AS NOTED

EC190C WOOD ASTRAGAL DETAIL FOR ECLIPSE FOLDING SYSTEMTriple Seal For Superior Sealing Performance

NOTE: For ease of mounting all hardware, it is recommended to use square edge doors.

1-5/16” (33.34mm)KT190C astragalsupplied by Eclipse Architectural

2134mm (84”)2438mm (96”)2743mm (108”)3048mm (120”)clear fir astragal 1-1/8”

(28.5mm)

ECP108-35BLKerf inserted fin pile

9/32”(7.14mm)

9/32”(7.14mm)

1/8” (3.23mm)

1-3/4”(44.5mm)

door

kerf slot1/8” x 3/8”(3.18mm x 9.5mm)

EC421 inserted weatherseal, brown, white or black

3/8” (9.5mm)

5/16” (7.94mm)

INTERIOR 3º bevel on active door ie: 35-7/8” (911mm) inside measurementwidth of door.

36” (914.4mm) outsidemeasurement of door

5/32” (4mm)

interior

ECP108-35BLKerf inserted fin pile

door with astragal

NO SCALE

1/8” (3.23mm)

FLUSHBOLT PLACEMENT

Suggested Flushbolt Lengths For Door Heights 80” to 120” (2.032m to 3.048m)

NOTE: End user may require longer flushbolts for top of doors for easier reach. When using E2 hardware for folding windows, top flushbolt length must be specified.

up to 84”(2134mm)

84-1/16”to 96”(2159mmto 2438mm)

96-1/2” to 108” (2403mmto 2743mm)

108-1/16”to 118”(2768mm to2997mm)

8” (200mm)flushbolt








NO SCALE

ASTRAGAL


E3 CORNER UNIT APPLICATION

E3 RADIUS APPLICATION (KT70 TRACK ONLY)

outside corner panel of 1L, 3L, 5L & 7L configurations

Mitre cut sill and head to suit length of opening

outside corner panel of 4R, 6R & 8R configurations

Apply lock set and/or deadbolt to active door or use flushbolts top & bottom (shown). If using interior flushbolts access from exterior not possible.

door stop

E3 sillINTERIOR VIEW

EXTERIOR VIEWEC417 seal

EC190astragal

4R3L

OUTSIDECORNER

Center point

DOORS

DOORS

KT70D-RADIUS bronze anodized top track (CUSTOM ORDER)*

EC23C-RADIUS clear anodized floor channel (CUSTOM ORDER)*

EC23D-RADIUS bronze anodized floor channel (CUSTOM ORDER)*

*CUSTOM ORDER, CALL FOR MANUFACTURING TIME.All supplied as one length only 120” (3048mm)

Minimum Radius14’-7” / 175” (4445mm)to inside face of top track.(Warranty on hardware void if under minimum radius)

RC

X

CP

Arc Length (AL)

R = Radius (length from the C.P. to the edge of the circle)

C = chord lengthX = height of crownCP = center pointAL = arc length

EXTERIOR INTERIOR

EXTERIOR

INTERIOR

RADIUS TRACK

Documents

In A Single Direction - Eclipse Architectural · 2019-08-22 · to build an Eclipse folding door system. ECE3DJ Eclipse E3 Drilling Jig See E3 Drilling Jig instruction sheet on (under