Turn the Dial Gap Position Turn the feeder “ON”. Turn the “SPEED” dial as shown for a starting point of envelope feeding. Press the “LOAD” button for the envelopes to move forward. Tighten the locking knob in place on the alignment rail. Impressia Feeder Guide Feeder Alignment Media Side Guide Move the feeder against the printer. Position the feeder alignment tab against the plastic located on the right side of the By-Pass Tray. Turn the feeder “OFF”. Using iQueue workflow software set the “Media Weight” to “Envelope”. The media side guides can be adjusted side to side for media width by using the locking levers on the outer part of the guides. Place the remaining amount of envelopes in the side guides. Loading Catalog Envelopes Loading #10 Envelopes Media Back Stop Loading 4 Bar Envelopes The back stop can be adjusted to apply proper pressure and media angle. Loading #10 Envelopes Turn the feeder “OFF”. Take one envelope, flap up - flap last and place between the media guides. Push the envelope under the separator pads. Tile a total of 2 envelopes and place them on the feeder. Place a handful of tiled envelopes on the feeder on top of the tiled envelopes. Hold the handful of envelopes in place and slide the media back stop against the the envelopes. Tighten the knob on the rear side of the back stop. Notice the position of the envelope and separator. If the envelopes do not move to the end sensor, press the load button again. Notice the envelopes angled with the media guide. Turn the feeder “OFF”. Adjust the media side guides. Take one envelope, flap up - flap last and place between the media guides. Push the envelope under the separator pads. Tile 2 envelopes and place them on the feeder. Place a handful of tiled envelopes on the feeder and slide the media back stop against the envelopes. Tighten the knob on the rear side of the back stop. The feeder separator pads can be adjusted to accommodate media thickness. When feeding envelopes or thin media, the separator pads need to be positioned near the bottom of the belt. fig A When feeding media that is thick or rigid, the separator pads needs to be near the top of the belt. fig B The height of the pads can be adjusted by loosening the center locking knob and raising pads for the thicker media. Envelopes or Thin Media Envelopes or Thin Media Thick Media Thick Media a) Dial at normal position a) Dial at normal position b) Dial Turning b) Dial Turning c) Dial Gap c) Dial Gap Bracket Bracket Lever Lever Knob Knob T. Move the feeder away from the printer. Open the printer side door. Remove both fuser brackets from the holders. Unlock both levers and slide the fuser back to remove from the printer. Turn the dial on the end of the fuser until there is a small gap between the 2 dials. Replace the fuser, press the levers down, return the brackets, close the printer door and put the feeder back into position. Set the separator pads at half and adjust the media side guides. Take one envelope, flap up - flap last and place between the media guides. Push the envelope under the separator pads. Tile 2 envelopes and place them on the feeder. Place a handful of tiled envelopes on the feeder and slide the media back stop against the envelopes. Tighten the knob on the rear side of the back stop. Notice the gap position. The envelopes will have curl before going into the feeder, this will not effect envelopes being printed. Depending on the envelopes type / style will determine the amount that can loaded in a stack. The separator pads height should be set so the envelopes do not overlap on the belts when feeding. Separators should be adjusted as high as possible but still able create media separation on the belt. Separator Pads Adjustments fig A fig B fig A fig B IMP Feeder Guide Rev 1.pdf

IMP Feeder Guide Rev 1 - XanteTurn the Dial Gap Position Turn the feeder “ON”.Turn the “SPEED”dial as shown for a starting point of envelope feeding. Press the “LOAD” button

Download PDF Report

Upload
others
View
3
Download
0

Embed Size (px)

Citation preview

Turn theDial

GapPosition

Turn the feeder “ON”. Turn the “SPEED”dial as shown for a starting point ofenvelope feeding. Press the “LOAD” button for the envelopes to move forward.

Tighten the locking knob in place on thealignment rail.

Impressia Feeder GuideFeeder Alignment Media Side Guide

Move the feeder against the printer.Position the feeder alignment tab against the plastic located on the right side of theBy-Pass Tray.

Turn the feeder “OFF”. Using iQueueworkflow software set the “MediaWeight” to “Envelope”.

The media side guides can be adjusted sideto side for media width by using the lockinglevers on the outer part of the guides.

Place the remaining amount of envelopesin the side guides.

Loading Catalog Envelopes

Loading #10 Envelopes

Media Back Stop

Loading 4 Bar Envelopes

The back stop can be adjusted to applyproper pressure and media angle.

Loading #10 Envelopes

Turn the feeder “OFF”. Take one envelope,flap up - flap last and place between themedia guides. Push the envelope underthe separator pads.

Tile a total of 2 envelopes and place themon the feeder.

Place a handful of tiled envelopes on thefeeder on top of the tiled envelopes.

Hold the handful of envelopes in placeand slide the media back stop against thethe envelopes. Tighten the knob on therear side of the back stop.

Notice the position of the envelope and separator.

If the envelopes do not move to the end sensor, pressthe load button again.

Notice the envelopes angled with the media guide.

Turn the feeder “OFF”. Adjust themedia side guides.

Take one envelope, flap up - flap last andplace between the media guides. Push theenvelope under the separator pads. Tile 2envelopes and place them on the feeder.

Place a handful of tiled envelopes on thefeeder and slide the media back stopagainst the envelopes. Tighten theknob on the rear side of the back stop.

The feeder separator pads can be adjusted toaccommodate media thickness. When feedingenvelopes or thin media, the separator pads needto be positioned near the bottom of the belt. fig AWhen feeding media that is thick or rigid, theseparator pads needs to be near the top of the belt. fig B The height of the pads can be adjustedby loosening the center locking knob and raisingpads for the thicker media.

Envelopes orThin Media

ThickMediaThickMedia

a) Dial atnormalposition

b) DialTurningb) Dial

Turning

c) DialGap

BracketBracketLeverLever

Knob

Move the feeder away from the printer.

Open the printer side door.

Remove both fuser brackets from theholders. Unlock both levers and slidethe fuser back to remove from the printer.

Turn the dial on the end of the fuser untilthere is a small gap between the 2 dials.

Replace the fuser, press the levers down,return the brackets, close the printer doorand put the feeder back into position.

Set the separator pads at half and adjustthe media side guides. Take one envelope,flap up - flap last and place between themedia guides. Push the envelope underthe separator pads. Tile 2 envelopes andplace them on the feeder.

Place a handful of tiled envelopes on thefeeder and slide the media back stopagainst the envelopes. Tighten the knobon the rear side of the back stop.

Notice the gap position. The envelopes will have curl before going into thefeeder, this will not effect envelopes being printed.Depending on the envelopes type/style will determinethe amount that can loaded in a stack.

The separator pads height should be set so the envelopes do not overlap on thebelts when feeding. Separators shouldbe adjusted as high as possible but stillable create media separation on the belt.

Separator Pads Adjustments

fig A

fig B

fig A

fig B

IMP Feeder Guide Rev 1.pdf