Ilat;8301807

f

J

Quick ReferenceTable of Contents:

Pages

[] Product dimensions

[] Cutout dimensions

]Before '/ou start

[] Ebctdcal requirements

[] [] Installation steps

mfyou need assistance:

Check your Use and Care Guide for a toll-free number to call or callthe dealer from whom you purchased this appliance. The dealer islisted in the Yellow Pages of your phone directory under"Appliances Household Major Service and Repair.

Call when you:

Have questions about built-in oven nstallation or operation.Need to obtain the name and number of an authorized servicecompany.

When you call, you will need:

The builtqn oven model number.The built-in oven serial number.

Both numbers are listed on the model serial rating plate, ocated onthe oven door or on the oven frame.

Read and save thesePart No. 8301807

Installer: Leave Installation instructions with the homeowner.

Homeowner: Keep Installation instructions for future reference.

Save Installation instructions for local electrical inspector's use.

27-I/2"recessedheight

29" max.recesseddepth

34-3/8"max.recessed

width

29" max.overallheight

Your safety aed the safety of others arevery important.

We have provided many important safetymessagesin tills manualand on your appliance.Atways read and obey aIIsafety messages.

This is the safety alert symbol.

Thissymboi alertsyou to potential hazardsthat can kiii or hurt you and others.

Ati safety'messageswiii foiiow the safetyalertsymbol andeither the word "DANGER"or"WARNING".Thesewords mean:

You can be killed or seriously injured if youdon't follow instructions.

AIi safety messageswiii teii you what the potentialhazardis, tell you howto reducethe chance ofinjury, andteti you what can happenif theinstructions are not followed.

[27-3/4"min.cutout

height

"_--- 36" min.cabinet width

l 34-1/2" _F-cutout width 5-1/4" bottom of

cutout to floor

SingLe undercounter oven(without cooktopinstalled above)

cabinet --_-

36" min.-- cabinet width --a_,*

27-3/4"min.

cutout

height

1-1/2 _ mirabottom ofcutout to

top ofcabinet

door

34-1/2"_<--- cutout --

width

1" top of cutout tobottom of uppercabinet door

t32"

bottom ofcutout to

floor

23-1/4"min.cutout depth

23"recessed

oven depth

recessedoven

Cabinet side view

oven_front

iMPORTANT: Observe all governing codesand ordinances.

Proper installation is your responsibility.Have a qualified technician install this oven.

Oven location should be away from strong draftareas, such as windows, doors and strongheating vents.

Cabinet opening dimensions that are shownmust be used. Given dimensions provideminimum clearance.

Recessed installation area must providecomplete enclosure around the recessed portionof the oven.

Electrical ground is required. See "Electricalrequirements."

Electrical supply junction box should be located3 inches maximum below the support surfacewhen oven is installed in a wall cabineL Drill a14nch minimum diameter hob in the right rearor left rear corner of the support surface to passthe appliance cable through to the junction box.For undercounter installation, it is recommendedthat the junction box be located in the adjacentright or left cabinet, if installing the junction boxon rear wall behind oven, junction box must berecessed and located in the upper or lower rightor left corner of cabinet.

Oven support surface must be solid, level andflush with bottom of cabinet cutout.

it is the customer's responsibility:To contact a qualified electrical installer.To assure that the electrical installation isadequate and in conformance with NationalElectrical Code, ANSI/NFPA 70 -- latest edition%and all local codes and ordinances.

Copies of the standards listed may be obtained from:National Fire Protection Association

One Batterymarch ParkQuincy, Massachusetts 02269

Tool needed:

, Phillips screwdriver

Parts supplied:• 2 screws

Page 1

ff codes permit and a separate grounding wire isused, it is recommended that a quaHified eHectriciandetermine that the grounding path and wire gaugeis in accordance with Mccallcodes.

Do Not ground to a gas pipe.

Check with a quaHifiedeHectrician if you are not sureoven is properHy grounded.

Do Not have a fuse in the neutraHor groundingcircuit.

Oven must be connected to the proper eHectricaHvoHtageand frequency as specified on themodeH/seriaHrating pilate. (The modeH/seriaHratingpilate is Hocatedon the oven door or on the ovenframe.}

[_ Models rated at 7.2 kW and below at 240 volts(5.4 kW and bellow at 208 voHts)require a separate30oampere circuit.

[_ A timeodeHayfuse or circuit breaker isrecommended.

[_ Connect directHyto the fused disconnect (orcircuit breaker box} through flexible, armoredor non-metaHHicsheathed, copper came (withgrounding wire).

[_ FHexibHearmored came from appHianceshouHdbe connected directly to junction box.

[_ Fuse both sides of the Mine.

[_ A U.hoHistedconduit connector must beprovided at the junction box.

[_ Do Not cut the conduit.

Wire sizes and connecqons must conform with therating of the appHianceand to the requirements ofthe NationaH EHectricaHCode, ANSH/NFPA70 -- Hatestedition (*, See Page 1) and a[[ local codes andordinances.

If the house has aluminum wiring, foHHowtheprocedure bellow.

a.) Connect the aHuminum wiring to the copperwire using specia[ connectors designed andUnderwriters Laboratories-Misted for joiningcopper to aHuminum. FoHHowthe eHectrica[connector manufacturer's recommendedprocedure.

b.) AHuminum/copper connection must conformwith Mccallcodes and industry-accepted wiringpractice.

Grasp over

frame to liftOVeR

Use screws to attachoven to cabinet

Reattach sidetrim pieces

Remove sidetrim

powersupply cable

Remov}X

shippingfeet

Remove trimSCreWS

Removeoven door

Preparation

Excessive Weight HazardUse two or more people to move andinstall oven.Failure to follow this instruction canresult in back or other injury.

IMPORTANT: Use both hands to remove ovendoors.

Do not use handHeor any portion of the front

Before moving oven across floor, check that ovenis on shipping base or sHideoven onto cardboardor hardboard.

Do not remove shipping feet at the front Mowercorners of oven.

latch on the hingein locked position -door free to openand close

latch on the hinge

position - doorready for rernoval

Remove trim screwPull trim out

Pull top of trimdown

• )off. Move oven chosetofinaHposition.

Remove and discardshipping materiaHs,tapeand protective fiHmfrom Do notthe oven. Do not reremove shipping base shipping feelor shipping feet at the front Mowercorners ofoven. The shipping feet wiHHprotect the Moweroven trim untiHoven is inserted into cabinet.Remove and set aside racks and other partsfrom inside oven.

m CompHeteHyopen oven door. In both backcorners of the door you wiHHsee door Hatchesin theHockedposition. Rotate both Hatchesforward to theunHockedposition.

Grasp outside edges of door with both hands.• Begin dosing door, atthe moment the door

stops dosing, Hiltand puHHdoor toward you.. Set door aside on a protective surface.

3B Remove trim screws attaching right and

Heftside trim to oven. Grasp the bottom end oftrim and puHHaway from oven. SHidetop end oftrim downward to remove trim from oven. Takecare not to scratch other surfaces with ends oftrim. Set trim and screws aside on protectedsurface.

Page 2

Electrical connectionffyour house has aluminum w,[dng, see"Electrical requirements", Page 2.

Electrical 8hock Hazard

Turn power supply off before connecting wires.

Use 8 gauge solid copper wire.

Electrically ground range.Failure to follow these instructions can resultin death, fire, or electrical shock.

TMs oven [s manufactured with white (neutral}power supply wire and a cabinet-connected baregrounding wire twisted together.

Feed oven came through opening [nthe cabinet. Make electrical connection

following the steps needed for your installation.

1. Disconnect the power supply.2. Remove the junction box cover.3. Connect oven came to junction box through the

U.L.q[sted conduit connector.4. Connect the two Mack wires together with

twist-on connectors.5. Connect the two red wires together with

twistoon connectors.6. Complete electrical connection according to

local codes and ordinances.

3-wire cable frompower supply

blackes

whitewire

white and

bare or greenwires

U,L,-listedcable from conduit

Figure 1 oven connector

If local codes permitconnecting cabinet-grounding

conductor to neutral whitewire in junction box:

7. Connect the bare or green andwMte oven cable wires to theneutral (white) wire in junctionbox. See Figure 1.

8. Replace junction box cover.

4-wire cable fromiunction power supply"

Figure 2 cable from connectoroven

If local codes do not permitconnecting cabinet=grounding

conductor to neutral whitewire in junction box:

7. Connect white oven came wire toneutral (white) wire [n junctionbox. See Figure 2.

8. Connect the bare or greengrounding oven cable wire to agrounded wire in the junctionbox. See Figure 2.

9. Replace junction box cover.

if connecting to afour-wire electrical system:

7. Connect white oven came wireto neutral (white) wire injunction box. See Figure 2.

8. Connect the bare or greengrounding oven cable wire tothe green grounding wire injunction box. Do not connectbare or green grounding wire toneutral (white) wire in junctionbox. See Figure 2.

9. Replace junction box cover.

AttachmentPush against seal area of oven front framewhen pushing oven into cabinet.

Do not push against outside edges.

5_ Lift oven into cabinet cutout usmg the

oven opening as an area to grip.

shippingfoot

Push against seal area of front frame to pushoven into cabinet until shipping feet almost

contact cabinet. Use a Phillips screwdriver toremove screws attaching shipping feet. Removeand discard shipping feet.

Push oven completely into cabinet and centeroven in cabinet cutout.

screws

6u iMPORTANT: Securely fasten oven to cabinet

using the two screws provided, insert the screwsthrough holes in mounting rails.

Slide topof trim up

Pushtriminto place.Replacetrim screw/

7m Slide top end of each trim upward onto oven

side rails. Push each trim into place at bottom oftrim. Use screws to attach each trim to oven. Takecare not to scratch other surfaces with ends of trim.

8u Replace oven racks.

9m Reinstall the oven door by inserting ends

of hinges into hinge slots [n the oven frame. Pushhinges in as far as they will go. Open the door(you will feel the door drop into place) and rotateboth hinge latches back to the locked position.

Close and open the door to check that the doordoses and opens completely. [f door does notclose or open completely, repeat the doorremoval step and reinstall door as describedabove.

Check operation

Turn on power supply. The displaypane[ will light up briefly. "PF" should appear [nthe temperature display.

the display. Press the "START" pad. Make sure theoven door is closed and the "ON" light is shown inthe display area. After 2 minutes, partially openoven door. You should feel heat from the oven.Press the "CANCEL" pad.If your oven does not heat or an "F", followed by anumber, appears in the display, contact your dealeror check the "If you need service..." section of thisinstallation instructions. To get the most efficient use

from your new oven, read yourUse and Care Guide. Keep Installation

Instructionsand Guide close to oven

for easy reference.

Page 3

If oven does not operate:[_ Check that ckcuit breaker is not tdpped or

house fuse blown.

[_ See Use and Care Guide for troubleshooting list.

If you need assistance:If you have questions about operating, cleaning ormaintaining your oven:

[_ Refer to Use and Care Guide.

[_ Ca[[the Consumer Assistance Center: Checkyour Use and Care Guide for a toil-freenumber to ca[[ or ca[[ the dealer from whom youpurchased this appliance. The dealer is listed inthe Yellow Pages of your phone directory under"Appliances -- Household -- Major -- Serviceand Repak."

If you need service:Maintain the quality built into your built-in oven byca[ling an authorized service company.To obtain the name and number of an authorizedservice company:

[_ Contact the dealer from whom you purchasedyour built-in oven; or

[_ Look in the Yellow Pages of your telephonedirectory under "Appliances -- Household --Major -- Service and Repair" for an authorizedservice company; or

[_ Ca[[ the Consumer Assistance Center. The toil-free phone number is listed in your Use andCare Guide.

When you ca[[, you wl[[ need:

[_ The built-in oven model number.

[_ The built-in oven serial number.

Both numbers are listed on the model/serial ratingplate, located on the oven door or on the ovenframe.

Part No. 8301807© 2003 Printed in U.S.A.