iDCS 500 Programming

January 2002

Programming

• Range of new Features have been added• For convenience have broken into 3 parts

– Technician– System– Station User

Technician

• MMC 804 - System I/O Parameters– Range of new services

• TRAFFIC - prints traffic reports• TRF/SMDR - for traffic plus SMDR• ALARMS - prints system alarms• ALM/TRAF - prints system alarms and traffic reports• REMO M/A - remote Maintenance & Admin - does not use

PCMMC as per current DCS.• UCD View - for UCD application program developed in the US

– requires UCD view to be enabled in MMC 860

– Serial cables as for DCS 70 (Compact 11)– Serial port speed - 38,400 baud (default 19,200)

Technician

• MMC 815 - Customer Database– Allows the customer database saved/recovered

from Smart Media card– SMDB: S: 00/00/00 00:00 - last time it was backed

up

Clear SMDB: Yes/No

Copy to SRAM: Yes/No– SRAM: S: 00/00/00 00:00 - last time it was backed up

Daily Save: 00:00 - daily save of database

Copy to SMDB: Yes/No - for manual database backup

Technician

• MMC 818 - Program Download– Allows the downloading of programs held on the

Smart Media card– Smart Media card supports the following programs

• M Version L VersionMCP main program MCP main program

LAN SCP

PRI LCP

PRI

LAN

– Note: 8 BSI, 4 BRI software cannot be supported on the Smart Media card

Technician

• MMC 826 - Clock Source– Allows the technician to define the primary clock

source and backup sources– M Version L Version

Priority 1 - 3 Priority 1 - 9

– Options• M Version C1:S1-3 or self• L Version Cx:S1-3 or self where x = cabinet 1-3

Technician

• MMC 850 - System Resources– Provides details of system resources idle and in

use:• DTMFR DSPs Use: xxx Free: xxx• CID DSPs Use: xxx Free: xxx• R2MFC DSPs Use: xxx Free: xxx• CONF Groups Use: xxx Free: xxx

– Adding in Use and Free provides total available in system

Technician

• MMC 851 - System Alarm Reporting– provides a buffer of last 100 alarms

• Requires a LAN card installed

• MMC 852 - System Alarm Assignment– sets the various types of alarms to provide an audible

indication at Keysets with Alarm keys programmed• requires a LAN card installed

• MMC 853 - Maintenance Busy Assignment– allows Trunks, stations and DSPs to be busied out for

maintenance purposes

Technician

• MMC 854 - Diagnostic time– sets time for system to perform diagnostic tests

• MMC 855 - System Options– allows the technician to check what is installed on

the MCP/SCP/LCP cards in the daughter board positions

– PSU60B installed– Dip Switch settings on cards if provided– whether daughter cards are installed on

Cadence/SVMi-8 or ITM3 by Cabinet/Slot no.

Technician

• MMC 856 - Tech Programming Log– keeps a log of all stations that have enabled

system programming - technician or System Admin level

– LAN card required for this option.

Technician

• MMC 859 Hardware Version– allows the Technician to view the firmware version

of the Programmable logic devices on the following cards:

• MCP including daughter card slots• Motherboard of Cabinets• SCP including daughter card slots• LCP including daughter card slots• 8BSI card??????

System

• MMC 209 Assign AOM – Max iDCS 64B AOMs per station

• M version - 2• L Version - 4

– Max iDCS 64B AOMs per system• M version - 4• L Version - 32

System

• MMC 210 - Tenant On/Off– Number of New Options

• DSP SSPDNAME - displays system speed dial name when set to ON

• Recall Pickup - allows a station user to pick up a reverting call at another station

• ICM EXT FWD - when set to ON allows intercom calls to be externally forwarded

• SEC 2 BOSS AA - when set to ON calls from a programmed Secretary station to the boss station will automatically answer

• DID ERR TONE - to provide error tone when an invalid DID number is received

• SL SELF RING - When set to ON allows a SLT to ring its own number and be rung back

System

• MMC 210 Continued• SGR INC Busy - when set to ON when all members of a station

group are busy it will return busy to exchange - ISDN only• KTS DISC ALM - When ON, generates system alarm when a

keyset plug out or in.• OFF Hook ALM - When ON, generates system alarm when a

phone maintains off hook condition longer than timer• TRSF CANCEL - when on allows SLT to handle 2 calls

simultaneously, pressing the recall key will toggle between the calls ON - pressing Recall key will disconnect the second caller

• RECALL DISC - When ON, the system disconnects a call when transfer recall.

• LCR DIALTONE - When ON, generates different dial tone when LCR dial mode.

System

• MMC 210 Continued• LCR DIALTONE - When ON, generates different dial

tone when LCR dial mode.• DSS KEY DPU - When ON, directed pick-up the call

when press ringing DS key. - ?????• BEGIN DGT DSP - when set to ON the first 11 digits of a

speed dial or redial number will be displayed. OFF the last 11 digits will be displayed

• ONE TOUCH FACC - when set to ON an ACCT key with an account code extender can be used. OFF account code must be dialled via keypad

• SGR ALL OUT - when set to ON all station group members may log out of the group

System

• MMC 210 Continued• CHAIN FWD - when set to ON a call to a station forwarded to a

station forwarded to a VMAA will send the caller into the mailbox of the last station. OFF caller will go to the original station’s mailbox

• TRUNK MONITOR - When ON, can override to trunk and a call is connected override extension when a original caller hang on. When OFF, can override to extension only and a call is disconnected when a original caller hang on.

• VOIP MFRALOC - When ON, a MFR assigned for VoIP tandem call when a call incoming from VoIP trunk to another trunk outgoing.

• NTWK AUTOTMR - When OFF, a call duration timer disabled via networking intercom call. - Available in Networking enabled only

System

• MMC 217 - Traffic Report Printout– allows traffic reports to be printed

• on demand, or hourly or timed for 3 shifts• Automatic printing always clears totals

• MMC 305 - Assigned Forced Codes– Account code with verification ie. checks codes set in MMC

708– Account codes no verification– Authorisation codes– None– To print Account codes on SMDR set option to yes in MMC

725

System

• MMC 501 - System Timers– new maximum timer setting 250 seconds

• MMC 502 - Station Timers– New items added

• Offhook Sel [000-250 sec] can set to 000 to disable• EFWD delay [000-250 sec] previously a system wide

timer rather than per station

System

• MMC 601 - Assign Station Group– M version 500 - 529– L version 500 - 549– New Group type -MSG Group (L version only)– Overflow 000 - 250 seconds– New Option Next Hunt (L version only)

• when timer is set will cause group to ring as a circular hunt group.

System

• MMC 603– M Version 0, 800 - 809– L version 0, 800 - 848– up to 99 members per trunk group

• MMC 604 - Internal Page Zones– up to 99 members

• MMC 605 - External Page Zones– up to 8 members– MISC card required

System

• MMC 606 - Assign Speed Block– M version 1500 bins– L version 2500 bins– 500 maximum per system, 50 per station max

• MMC 607 - UCD Options– new option added - All Out > Final destination

• all members of group can be logged out

• MMC 608 - CID Review Block– M version 1000 bins– L version 1550 bins

System

• MMC 609 - Call Log Block– 1500 bins available for outgoing call log– Maximum of 50 per station– LAN card required

• MMC 701 COS– Features are broken up into different groups

• Useable features• Call STN Group• Call Trunk Group• Call BIVMS STN

System• MMC 707 - Authorisation Codes

– M version 250 entries - up to 4 digits

– L version 500 entries - up to 10 digits

• MMC 708 - Account Codes– M version 500 entries

– L version 999 entries

• MMC 709 - Toll Pass Codes– PBX Access Codes - 1 to 5

– Special codes - 1 to 10

– Toll Override - 1 to 8• bypasses all dialling restrictions

• up to 14 digits

• system will use OVRD trunk grp (LCR code cannot be used)

– OVRD Use Trunk Grp - none, 0, 800 - 848

System

• MMC 714 - DID Digit Table– M version up to 400 entries– L version 999 entries– DID digits - up to 16– 1-6 ring Plans– MOH source can be associated with each DID

number

System

• MMC 722 - Key Programming– Number of new key options

• ACC XXX - account code from MMC 708 (L version)• Alarm Key• CAD - Call Activity key to view activity on Trunks and

Extensions• CONP - Networking feature ???• DNDO - DND override key• EP - Established call pickup must program an extender for

SLT extension - dialing via modem in PC poor man’s CTI• LANREQ - LAN Request (LAN board required)• MCID - Malicious Call Trace Key• LOG - Call log key to view previous calls LAN card required

System• MMC 722 Continued

• MS - manual signalling - networking feature ???

• MW - VM Message wait key for other extensions, groups, virtual extensions

• NOCLIP - stops the sending of CLI information

• PMSG - program message key with extender

• PRB - privacy release bridge - allows another station to dial trunk number and enter conversation

• PROG - allows a station user to program certain functions for other stations eg. STN FWD, STN Name, STN lock, Time and date without entering program mode.

• PTHR - Path Replacement (Networking feature)

• RP - Ring Plan with ring plan extender

• RTO - Ring Time Override

• SETDND - allows a station to set DND for another station

System

• MMC 722 Continued• SYSALM - system diagnostic alarm key (LAN card

required)• TRARPT - Traffic report key

System

• MMC 724 - Numbering Plan– New Options added

• Network LCR Number Plan - L version only• Virtual Extension Number Plan - SLT

– 3501 - 3516 - M version– 3501 - 3570 - L version

– New Feature Codes• CONP - ???? (Networking Feature)• DNDO - DND override• PTHR - Path replacement (Networking Feature)• SLTMMC - allow SLT to use MMC• SRELOC - code to do Set Relocate

– poor man’s hot desking function

System

• MMC 725 - SMDR Options– New Option

• Print KMMC Log in/out - yes/no

• MMC 802 - CUSTOMER MMC– Now this can be programmed by tenant 1&2

System

• New Ring Plans - 6 in total

• Impacted MMCs– MMC 507 Assign Ring Plan time– MMC 211 Door Ring Assignment– MMC 212 Alarm Ringing Station– MMC 214 DISA Alarm Ringing Station– MMC 301 Assign Station COS– MMC 403 Trunk Toll Class– MMC 406 Trunk Ring Assignment– MMC 421 Assign MSN Digit– MMC 512 Holiday Ring Plan - I plan can be assigned– MMC 600 Assign Operator Group– MMC 714 DID Digit Translation– MMC 733 AA Plan– MMC 758 Cadence VM/Day/Night

System

• 6 Ring Plans per day• each plan can be assigned manually or automatically

via MMC 507• Ring Plan times are assigned per day• MMC 507 Assign Ring Plan Time

– Program START and End Time for each of 6 Plans– Must be done for each day of Week– ANS/RLS for ALL does not operate

Ring Plans

• Before Programming Ring Plans it is important to draw a diagram

• The diagram should show the time of day along the bottom and Ring Plans 1-6 on the vertical axis

• See example

Ring Plans

00:00

02:00

04:00

06:00

08:00

10:00

20:00

22:00

23:59

12:00

18:00

14:00

16:0

0

Sunday

00:0

0

02:00

04:00

06:00

08:0

0

10:00

20:00

22:00

23:59

12:00

18:00

14:00

16:00

Saturday

00:00

02:00

04:00

06:00

08:00

10:00

20:00

22:00

23:59

12:00

18:00

14:0

0

16:00

M o n d a y - F rid a y

Ring Plans

00:0

0

02:0

0

04:0

0

06:0

0

08:0

0

10:0

0

20:0

0

22:0

0

23:5

9

12:0

0

18:0

0

14:0

0

16:0

0

Typical W eekday

Lunch

The Ring Plan that applies is the highest numbered Ring Plan that can be seen looking down from the top of the diagram

Ring Plans

midnight 05:30 1 Ring Plan 105:30 06:00 2 Ring Plan 206:00 08:00 4 Ring Plan 408:00 10:00 5 Ring Plan 510:00 02:00 6 Ring Plan 602:00 03:00 5 Ring Plan 503:00 05:30 3 Ring Plan 305:30 10:00 2 Ring Plan 210:00 midnight 1 Ring Plan 1

For the previous example the chart below shows the actual ring plan in operation

Ring Plans

• Ring Plan (RP) Keys can be assigned for each Ring Plan.– If the RP key is used to set the ring plan manually,

the system will remain in the new ring plan until it is cleared

• Ring Time Override (RTO) key– If the RTO key is used to override the ring plan in

operation, the system remains in this plan until the start time of the next Ring Plan

• RTO ‘0’ will clear the setting

User• MMC - 102 Call Forward

– new Options• Forward DND

• CFU - Call Forward Unconditional (Networking Feature)

• CFB - Call Forward Busy (Networking Feature)

• CFNA - Call Forward No Answer (Networking Feature)

• MMC 110 - Station On/Off– New Options

• Not Cont.CID - displays CID on Keyset display during call if set to ON and Auto timer is set to OFF

• DISP SPD NAME - displays speed dial name if set to YES - refer MMC 210 for system wide setting

• Secure OHVA - OHVA will only work if busy keyset is using the Handset if set to ON

User

• MMC 115 Set Program Message– M version 20 messages– L version 30 messages

• Messages 26-30 can have a time or date associated with them

– Program Messages are set in MMC 715

iDCS 500 Programming

• 3 Levels of Programming– Technician– System Administrator– Station User

• Programming methods– PC - DPAP-PCMMC

• local or Remote• System Administrator Version available

– Keyset

• Programming consistent with existing DCS systems– MMC based

DPAP-PCMMC

• Windows based• Systems can be configured Off-Line

– Card Configuration– Number Plan entered manually

• Data can be imported from Excel Spreadsheet– MMCs 104, 105, 404, 405, 705, 707, 708

• Option to format – MMC group mode

• 100s, 200s etc.

– Functional Group mode• Stations, System, Groups/Tables, etc.