www.icotera.com Icotera A/S reserves the right to change specifications without further notice.

IGW3000 Residential Gateway

QOS

WAN INTERFACE

LAN INTERFACE

LAYER 2FEATURES

LAYER 3

High performance solutionIntuitive designExtensive IPv6 supportSlide-on designPhenomenal aesthetic designOptional integrated feature rich CATV solutionOptional external battery backupLow power consumptionDeveloped and Manufactured in Europe

Single mode fiber (ITU-T G.652)SC/PC connector 1000Base-BX10 compliantTx: 1310, Rx: 1480-1600Full-duplex transmissionOperating distance: 20kmTransmit power: -7 – -2dBmReceive power: -3 – -23dBmClass 1 laser productAuto detection of 100Mbps or GigabitMTU size: <= 2048 bytesMonitor optical signal level (optional)

VFR-liteGigabit wirespeed forwardingIGMP proxy with fast-leave and monitoringP2P filters/rate-limitingStatefull Packet InspectionIPv4 SNAT, DNAT, DMZ DNS proxy DHCP client and serverIPv6 Prefix delegation RFC3769 6RD DHCP client and serverPPPoE (optional)IP L2-L4 filters (256 rules per filter)Connection tracking with monitoringUPnP

8 QueuesLayer 3 QoS features Packet classification Marking Queuing Scheduling Rate Limiting802.1p priority802.1p remappingToS classificationDiffserv classification

4 or 8 x RJ45 connectors 10/100/1000 Base T(X)Auto-negotiation for speed and duplexAuto MDI/MDXJumbo packets802.1x

Multiple bridge instancesGigabit wirespeed forwardingIGMP snoopingWire-speed bridgingVLAN supportWiFi supportTransparent IPv6 forwarding802.1p

IGW3000 Residential GatewayThe Icotera IGW3000 Residential Gateway integrates optical Ethernet-based data transmission with Layer 2-4 functionality and VoIP, 802.11bgn WiFi, CATV and USB.

IGW3000 features a powerful dual core architecture, where all realtime tasks are handled by a dedicated core, leaving one core available for other immediate tasks. This means that the system is still responsive, even while doing VoIP, Gigabit routing of IPv4/IPv6 with NAT (IPv4) or bridging at wirespeed. Full IGMP proxy functionality for a router instance and IGMP snooping for bridges is provided to minimize the multicast traffic load.

A VRF-lite functionality is provided where up to 4 inde-pendent router instances can be created, all featuring support for multicast, filtering up to level 7, NATv4 functionality and several IPv6 mechanisms.

To provide simple Layer 2 functionality, a bridge system is implemented and up to 4 separate bridging instances can be created. A maximum of 24 inter faces (LAN, WAN and WiFi) can be added and configured as members on different routers or bridges.

The CATV AGC receiver offers cable television services to the subscriber with monitoring and configuration of the power levels. As an option, IGW3000 offers a complete filter solution with high block band attenuation for individual RF channel plans.

IGW3000 can be controlled by a number of management protocols or our fail-proof zero-touch auto provisioning mechanism.

www.icotera.com Icotera A/S reserves the right to change specifications without further notice.

IGW3000 Residential Gateway

MANAGEMENT & MONITORING

STATUS LEDs

FIBER TERMINATION UNIT (FTU)

VOIP (OPTIONAL)

CATV (OPTIONAL)

GENERAL SPECIFICATIONS

USB (OPTIONAL)

WIFI INTERFACE (OPTIONAL)

Shared or separate IP interface for managementIP filters for all local servicesSSHv2 with key authenticationTelnet with authenticationEnd-user orientated web interface (configurable) WiFi LAN network Port forwarding Status and monitoringTR-069 supporting TR-104 (VoIP) TR-98 (Network)

CLI with auto-completionSNMP v1/v2 (IF-MIB, ICOTERA private MIB) Extensive debug possibilitiesPacket dumpingAll settings are stored locally in flashZero-touch configuration with DHCP/TFTP or TR-069Automatic firmware update (polling)Failsafe firmware upgrading

Configurable by operator and/or end-userAuto off after timeout periode Power/Info WAN status (link/traffic)

VoIP port 1 VoIP port 2 CATV status LAN status (link/traffic,

duplex)

The IGW FTU is an optional part numberSlide-on mechanism for easy installationFTU support for Gas block unit (sold separately) WDM filter (sold separately)Optional blind cover for FTU

2 RJ11 connectors2 separate POTS lines SIP (RFC3261)5 REN supportDTMF signaling SIP INFO Inband RFC 2833Adaptive jitter bufferDNS SRVCaller ID support (DTMF/FSK/DTMF DK)CLIRAdvanced dialplanB-Number manipulation

Class 5 services Forward all calls Forward on busy Forward on no answer Call waiting Codecs G.711A a-law G.711U μ-law G.729Modem/Fax supportT.38 fax (optional)Silence suppressionLEC (Line Echo Cancellation)G.165 Echo cancellation CNG (Comfort Noise Generation)

OPTICAL PARAMETERS:

Saturation power: 3 dBm

Input level range: -10 to 0 dBm

Input wave length: 1310/1550 nm

Optimal AGC range -6 to 0 dBm

Equivalent input noise (amplifier + diode): 8 pA/√Hz

Responsivity λ=1310nm: 0,8 A/W

Responsivity λ=1550nm: 0,9 A/W

Optical connector: SC/APC

Standard Single Mode fiber (ITU-T G.652)

Software monitoring of RX level in 0.1dB steps.

RF PARAMETERS:

Frequency range: 45 to 900 MHz

Output level at -3dBm (0 dB slope, 3,5% OMI w/2 filters): 75dBuV

Output level at -3dBm (4 dB slope, 3,5% OMI): 78dBuV

Linearity: ±1 dB

CNR (CENELEC 42 channels): >= 51 dB

CSO (CENELEC 42 channels): <= 65 dBc

CTB (CENELEC 42 channels): <= 65 dBc

RF filters (optional): up to 2

Filter attenuation in block band: > 50 dB

Filter attenuation in pass band: < 3 dB

Filter and output power level controllable by software

RF connector 75 Ohm “F”

DC12V input ±10%Power consumption: 12watt (incl. 4LAN, 2VoIP, WiFi and CATV) Operating temperature: 0 – 45cStorage temperature: -20 – 85c

Humidity: 5% - 95% (non-condensing)Optional external battery PSUWeight: 800gSize: 190 x 110 x 48 mm (W x H x D)

Icotera partner:

2 x USB portPrepared for Zigbee Z-wave

CATiq Storage

IEEE 802.11b/g/nIEEE 802.11a (optional)Multiple SSIDsEncryption WEP64 WEP128 WPA WPA2

MAC filtering2T2R MiMoWPS802.1xInternal antennas (external optional)