HYUNDAI Genuine Accessories HYUNDAI Genuine Accessories NO GOOD CLICK When disconnecting connectors,

  • View
    0

  • Download
    0

Embed Size (px)

Text of HYUNDAI Genuine Accessories HYUNDAI Genuine Accessories NO GOOD CLICK When disconnecting connectors,

  • HYUNDAI Genuine Accessories

    Vehicle Model Elantra Accessory Interior Lighting Kit

    Model Year 2017 ~ Difficulty ( B )

    Basic Required Hand Tools

    Instructional Symbols / Definitions

    Difficulty stated above reflects the minimum level of expertise required to install

    the accessory.

    ( A ) Customer ( B ) Dealer Technician ( C ) Master Technician

    Note:

    For SE models with Base Radio: Use Pin-8 and Pin-10 of the 16-Pin AUX Connector for the power connections.

    Part No. F3068 ADU00

    NOTE: THIS INTERIOR LIGHT KIT IS NOT APPLICABLE TO MANUAL TRANSMISSION, 1.4T ECO, OR SPORT ELANTRA MODELS.

    - Accessory Installation

    Ratchet 10mm Socket 13mm Socket Wire Cutters

    Pliers Center PunchTorque Wrench

    Electric Drill 19/32" Drill Bit #2 Phillips

    Screwdriver

    Nylon Trim Panel

    Removal Tool

    Tape Measure

    Deburring Tool

    3/16" Drill Bit Scissors

    Denotes safety equipment required to be used such as a mask, safety glasses, gloves, and hearing protection.

    Safety Glasses

    Hearing Protection

    Mask

    Gloves

    Denotes instructional steps necessary to complete the process.

    Denotes quality processes to be checked prior to moving to the next step.

    Denotes cautions to be taken to avoid physical injury or electronic component damage.

    Denotes warnings that may lead to serious physical injury or vehicle damage.

    Denotes specific tools that are necessary to complete the step.

    Denotes cautions to be taken to avoid vehicle and component damage.

    Notes to the Installer: 1) Read the entire installation instructions prior to beginning the installation of this accessory. 2) Make sure the vehicle is completely clean before the accessory is installed. 3) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed. 4) To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet/mats. 5) Always wear appropriate safety gear to include gloves and safety glasses when required. 6) Factory wire colors are subject to change, please use the specified pin # in the harness connector to identify the correct wire for T-Tap installation.

    FMVSS 110 Compliance Information

    Part Number: F3068 ADU00

    0.67 lbs 0.3 kg

    (Gross Weight)

    All dealers must determine if the weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load Carrying Capacity Reduced” label must be installed. A black, fine- point, indelible marker must be used to write by hand onto the label, the reduced carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories. Load Label Part Number:

    NP070 - 09003

    Elantra

    Interior Lighting Kit

    Revision Date

    07/27/2016 Page 1 of 15

  • 1 20 2 2

    Description

    LED & Bracket Assembly

    HYUNDAI Genuine Accessories

    Kit Overview

    No. Qty.

    LED

    1 1

    Wire Harness

    2 1

    Hardware Bag

    4

    3 1

    5 1

    Switch

    6 1 Installation Instructions

    Hardware Total

    E

    7 1

    Hardware Overview

    A C D

    Plastic Fastener M8 x 1.5mm Flanged

    Head Nut Wire Ties * T-Tap

    25

    * Extra components intentionally placed in kit as spares.

    Please follow directions for proper placement of each component.

    1

    Glove Box Information Card

    1

    3

    5 6 7 4

    2

    Elantra

    Interior Lighting Kit

    Revision Date

    07/27/2016 Page 2 of 15

  • Disconnecting Connectors Lock Connectors

    When disconnecting connectors, grasp the connectors , not the wire When locking connectors, listen for a click indicating

    they are securely locked.

    HYUNDAI Genuine Accessories

    NO GOOD

    CLICK

    When disconnecting connectors, press the lock tab and pull apart by grasping the connectors. DO NOT PULL ON WIRES.

    Elantra

    Interior Lighting Kit

    Revision Date

    07/27/2016 Page 3 of 15

  • N

    O

    T

    E

    1. Continue to pull the Shift Knob up to remove the Shift Knob Assembly.

    2. Store the Shift Knob Assembly in a safe location for reinstallation. N

    O

    T

    E

    1. Close the Forward Tray Cover.

    2. Dislodge the Center Console Cover by gently pulling upwards to release

    the four (4) pressure clips.

    Caution: DO NOT scratch the Trim Panels or Shift Knob Assembly. Caution: DO NOT scratch the Trim Panels.

    DO NOT lose the pressure clips.

    3 Nylon Trim Panel Removal Tool 4

    N

    O

    T

    E

    1. Park the vehicle on a level surface.

    2. Apply the Parking Brake.

    3. Move the Gear Selector from Park (P) position to Drive (D) position.

    4. Record all pre-set radio stations (if applicable).

    5. Disconnect and isolate the vehicle's Negative Battery Cable.

    N

    O

    T

    E

    1. Carefully release the six (6) clips surrounding the Shifter Boot by

    gently pulling the Shift Knob upwards.

    WARNING! Shock Hazard. Do not touch vehicle's negative battery

    terminal to vehicle's positive battery terminal. Serious physical injury

    or vehicle damage may occur.

    Caution: DO NOT scratch the Trim Panels or Shifter Boot.

    HYUNDAI Genuine Accessories

    Ratchet and 10mm Socket 1 2

    Elantra

    Interior Lighting Kit

    Revision Date

    07/27/2016 Page 4 of 15

  • HYUNDAI Genuine Accessories

    5 Nylon Trim Panel Removal Tool 6

    N

    O

    T

    E

    1. Lift the Center Console Cover to access the Electrical Connectors.

    2. Disconnect any Electrical Connectors and remove the Center Console

    Cover from the vehicle.

    3. Store the Center Console Cover in a safe location for reinstallation.

    N

    O

    T

    E

    1. Remove the passenger side HVAC Close Out Panel by pressing the

    three (3) tabs rearward.

    2. Store the HVAC Close Out Panel in a safe location for reinstallation.

    Caution: DO NOT scratch the Center Console Cover. Caution: DO NOT scratch the HVAC Close Out Panel or surrounding

    Trim Panels.

    #2 Phillips Screwdriver 7 8

    N

    O

    T

    E

    1. In driver side footwell area, remove the one (1) plastic screw

    and one (1) push clip as noted in step 8.

    2. Route the Interior Light Wire Harness (Driver Side Label) through the

    front left side of the Center Console, towards the Driver Side Footwell

    area.

    N

    O

    T

    E

    1. Pull the Interior Light Wire Harness (Driver Side Label) completely

    through

    to the Driver Side Footwell area as shown.

    2. Pull the Harness, taking up all the slack.

    3. Replace the one (1) plastic screw and one (1) push clip removed in

    step 7.

    Caution: Make sure not to route the Harness near any sharp edges. Caution: Make sure not to route the Harness near any sharp edges.

    Plastic Screw

    Interior Light Wire Harness Driver Side

    HVAC Close Out Panel under Glove Box.

    Elantra

    Interior Lighting Kit

    Revision Date

    07/27/2016 Page 5 of 15

  • HYUNDAI Genuine Accessories

    9 Wire Cutters, Ratchet, 13mm Socket and Torque Wrench 10

    N

    O

    T

    E

    1. Locate the unused M8 stud high up on the bulkhead, just below the

    large factory wire harness.

    2. Mount the driver side LED assembly, using one (1) M8 nut as shown.

    Hand tighten only. N

    O

    T

    E

    1. Secure LED assembly to vehicle main harness, that passes through the

    bulkhead grommet, using one (1) wire tie as shown.

    2. Torque M8 Nut to 9.8 - 14.7 Nm (1.0 - 1.5 kgf.m, 7.2 - 10.8 lb-ft).

    3. Trim excess wire tie material.

    11 12

    N

    O

    T

    E

    1. On driver's side, route harness up beside HVAC housing and secure

    to side of housing with wire tie #1. Do not fully tighten wire tie.

    2. Continue to route the harness up above the HVAC vent and secure with

    wire tie #2 to factory HVAC damper actuator harness. Do not fully tighten

    wire tie.

    3. Route the harness down and secure with wire tie #3 to forward white

    connector on MDPS module. Do not fully tighten wire tie.

    N

    O

    T

    E

    1. Route the harness across the top of the MDPS module over towards the

    fuse box area.

    2. Secure the harness to the 2-Pin MDPS power and ground connector with

    wire tie #4. Do not fully tighten wire tie.

    3. Route the harness around the MDPS module and along the large factory

    harness towards the LED/bulkhead, and secure with wire tie #5 and #6

    as shown. Do not fully tighten wire ties.

    Caution: Be sure not to route the Interior Light Harness near any sharp

    edges.

    Caution: Be sure not to route the Interior Light Harn

Recommended

View more >