Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Abstract
To improve the hybrid dye-‐sensitized solar cell (HDSSC)’s ef>iciency, new metal-‐phthalocyanine solutions were employed. In this research, copper, silver, and zinc phthalocyanine were synthesized and applied as molecular sensitizers into the cells. It was hypothesized that HDSSCs based on metal-‐phthalocyanines would generate better ef>iciency than those made of phthalocyanine dyes. UV-‐Visible spectroscopy was the >irst test to verify if three metals were successfully chelated into the metal cores of phthalocyanines. Depend on particular lighting conditions; the optimal energy ef>iciency of these HDSSCs of 1.6% has been reached.
Background Hybrid solar cells are solar cell devices that contain both organic and inorganic semiconductors, and combine the unique properties of inorganic semiconductors. This combination of materials in the photoactive layer can result on a greater ef>iciency when converting light into electricity 1.
For the inorganic semiconductor, titanium dioxide (TiO2) is introduced because of its high ef>iciency and low cost compared to porous silicon or gallium arsenide. Gratzel cells contain particles of TiO2, which are coated with a dye that absorbs a wide range of wavelengths given off by sunlight. These cells are placed between two electrodes in an electrolyte solution containing iodine ions and generate electricity when the energy captured by the dye. Metal-‐phthalocyanine was used as organic dye synthesized material for photo-‐conducting in chemical sensors and electricity-‐generating in photovoltaic cell 2. Copper, silver, and zinc are three good candidates for metal core in phthalocyanine structure because of their high thermal conductivity and electrical conductivity.
Project Design
Methodology Syntheses of Metal-‐Phthalocyanine Solutions • Synthesize CuPc by mixing Pc powder and copper acetate monohydrate in the
presence of pyridine solvent. • Synthesize AgPc by mixing Pc powder and silver nitrate in the presence of
ethanol solvent. • Synthesize ZnPc by mixing Pc powder and zinc acetate dihydrate in the presence of acetonitrile solvent. • Run the UV-Visible tests for all solutions. Preparations of Semiconductor Titanium Dioxide • Prepare TiO2 paste by adding nano-‐crystalline titanium dioxide with very
diluted acetic acid and Triton X100. • Paste titanium dioxide on conductive side of tin-oxide coated glass. Constructions of Hybrid Dye-‐Sensitized Solar Cells • Add the dye-sensitized solutions drop-‐wise on tin-‐oxide coated glass. • Heat another tin-‐oxide coated glass under Bunsen burner to coat the
conducting side with carbon. • Assemble two glass plates with coated sides in. • Add I3-‐ solution drop-wise to the edge of the plate. • Measure the currents and voltages by using the multimeter.
Conclusions • This hybrid dye-‐sensitized solar cell model is produced at lower cost and more friendly to the environment than other commercial models. • The overall energy conversion ef>iciency of metal-‐phthalocyanine solutions was higher than those of phthalocyanine dyes . • This result fully supported the hypothesis that metal-‐phthalocyanine solutions would generate better ef>iciency than phthalocyanine dyes.
References 1. Günes, S. & Serdar Saiciftci, N. (2008). Hybrid Solar Cells, Inorganica Chimica
Acta, Vol. 361, pp. 581-‐588. 2. Kadish K., Kevin M. Smith, Guilard R.,The Porphyrin Handbook, Vols. 15-‐20; (eds);
Academic Press 2003. 3. O’regan B. and Gratzel M. “A low-‐cost, high ef>iciency solar cell based on dye-‐
sensitized colloidal TiO2”. Nature 353, 737 -‐ 740 (24 October 1991).
Hybrid Dye – Sensitized Solar Cells based on Titanium Dioxide and Metal - Phthalocyanines
*Attendees: Ngoc Do and Nhi Vo. Advisor: Professor Drew Brodeur* Department of Chemistry and Biochemistry, Worcester Polytechnic Institute
Figure 1: Hybrid solar cell structure 1
Figure 2: Titanium dioxide structure and cell 3
!
Figure 5: Current and Voltage Measurements under Normal Room Illumination
Syntheses of Metal-‐
Phthalocyanine Solutions
Copper phthalocyanine
(CuPc)
Silver phthalocyanine
(AgPc)
Zinc phthalocyanine
(ZnPc)
Constructions of Hybrid
Dye-‐Sensitized Solar Cells
Semiconductor: Titanium dioxide
Dye-‐sensitized materials: Metal-‐ phthalocyanine
solutions
Electrolyte: I3-‐ solution
Comparisons of Energy
Conversion Ef>iciency
Normal room illumination
Compact UV–Light (UVGL-‐25)
Sunny daylight
Cloudy daylight
Results The UV-‐Visible test was run to characterize the metal-‐complexes. The UV-‐Visible spectra con>irmed the attachment of these conducting metals on porphyrin ring by comparing the experimental maximum wavelengths with the literature values. The energy ef>iciency of three metal-‐phthalocyanine solutions under normal room illumination, compact UV-‐lamp, sunny day and cloudy light were computed by using the Equation 1 and presented in Figure 7.
Figure 3: Metal-‐Phthalocyanine Structure 2, M = Cu2+, Ag+, and Zn2+
Figure 6: UV-‐Visible Spectrum of Copper Phthalocyanine
Table 1: Experimental and Literature Wavelengths of Metal-‐Phthalocyanines
η =PmE × A
P = IV =V2
R
η =V 2
E × A×R
Equation 1: Energy Conversion Ef>iciency Formula
Figure 7: Column Chart for Comparisons between the Ef>iciency of Phthalocyanine and Metal-‐Phthalocyanine Solutions
Figure 4: Mechanism of Dye-‐Sensitized Solar Cell 2