Huawei Certification Training Catalog (Subcontractors) V1.2

Huawei Certification Training Catalog（Partner）

COMMERCIAL IN CONFIDENCE 1

Huawei Certification Training Catalog （Partner）



HUAWEI Learning Service

2013



CONTENTS

1 IP Technology Certification Training ...................................................................................................................... 5

1.1 HCDA-HNTD (Huawei Certified Datacom Associate-HuaWei Networking Technologies and Device)

Training 5

1.2 HCDP-BCRN (Huawei Certified Datacom Professional-Building Carrier Routing Network) Training ........ 6

1.3 HCDP-BCAN (Huawei Certified Datacom Professional-Building Carrier Access Network) Training.......... 7

1.4 HCDP-BITN (Huawei Certified Datacom Professional-Building IP Telecom Network) Training ................. 8

1.5 HCIE (Huawei Certified Internetwork Expert-Improve Carrier Network Performance) Training................. 9

2 Cloud Computing Certification Training ................................................................................................................ 11

2.1 HCNA-HCTD (Huawei Certified Network Associate- Huawei Cloud Technologies and Device) Training.. 11

3 LTE Certification Training ....................................................................................................................................12

3.1 HCNA-LTE (Huawei Certified Network Associate — LTE) Training ........................................................12

3.2 HCNP-LTE (Huawei Certified Network Professional — LTE) Training ....................................................13

3.3 HCNP-EPC (Huawei Certified Network Professional — EPC) Training ..................................................14

4 Access Network ..................................................................................................................................................15

4.1 Huawei Certified Network Associate-Huawei Access Network Technologies and Device Training Outline

15

4.2 Huawei Certified Network Professional-Huawei Access Network Technologies and Device Training

Outline 15

5 Optical Network ..................................................................................................................................................16

5.1 Huawei Certified Network Associate-Huawei Optical Network Technologies and Device Training Outline

16

5.2 Huawei Certified Network Professional-Huawei Optical Network Technologies and Device Training Outline

16

6 Microwave Product .............................................................................................................................................17

6.1 Huawei Certified Network Associate-Huawei Microwave Technologies and Device Training Outline .......17

6.2 Huawei Certified Network Professional-Huawei Microwave Technologies and Device Training Outline ...18

7 Mobile Soft Switch ..............................................................................................................................................19

7.1 Huawei Certified Network Associate-Huawei Mobile Soft Switch Technologies and Device Training Outline

19

7.2 Huawei Certified Network Professional-Huawei Mobile Soft Switch Technologies and Device Training

Outline 20

8 NGN...................................................................................................................................................................22

8.1 Huawei Certified Network Associate-Huawei NGN Technologies and Device Training Outline................22

8.2 Huawei Certified Network Professional-Huawei NGN Technologies and Device Training Outline ...........24

9 MGW&SBC ........................................................................................................................................................25

9.1 Huawei Certified Network Associate-Huawei MGW&SBC Technologies and Device Training Outline .....25

10 USC ...................................................................................................................................................................27

10.1 Huawei Certified Network Associate-Huawei USC Technologies and Device Training Outline ................27

10.2 Huawei Certified Network Professional-Huawei USC Technologies and Device Training Outline ............28

11 SG .....................................................................................................................................................................29

11.1 Huawei Certified Network Associate-Huawei SG Technologies and Device Training Outline ..................29



11.2 Huawei Certified Network Professional-Huawei SG Technologies and Device Training Outline ..............30

12 GSM ..................................................................................................................................................................31

12.1 Huawei Certified Network Associate-Huawei GSM Technologies and Device Training Outline ...............31

12.2 Huawei Certified Network Professional-Huawei GSM Technologies and Device Training Outline ...........32

13 WCDMA .............................................................................................................................................................33

13.1 Huawei Certified Network Associate-Huawei WCDMA Technologies and Device Training Outline ..........33

13.2 Huawei Certified Network Professional-Huawei WCDMA Technologies and Device Training Outline ......34

14 CDMA ................................................................................................................................................................35

14.1 Huawei Certified Network Associate-Huawei CDMA Technologies and Device Training Outline .............35

14.2 Huawei Certified Network Professional-Huawei CDMA Technologies and Device Training Outline .........37

15 Wimax ................................................................................................................................................................39

15.1 Huawei Certified Network Professional-Huawei Wimax Technologies and Device Training Outline.........39

16 GSM RNP&RNO ................................................................................................................................................40

16.1 Huawei Certified Network Associate- Huawei GSM RNP&RNO Technology Training Outline .................40

16.2 Huawei Certified Network Professional - Huawei GSM RNP&RNO Technology Training Outline ............41

17 WCDMA RNP&RNO ...........................................................................................................................................42

17.1 Huawei Certified Network Associate-WCDMA RNP&RNO Training Outline ...........................................42

17.2 Huawei Certified Network Professional-WCDMA RNP&RNO Training Outline .......................................42

18 CDMA RNP&RNO ..............................................................................................................................................43

18.1 Huawei Certified Network Associate-Huawei CDMA RNP&RNO Technologies Training Outline .............43

18.2 Huawei Certified Network Professional-Huawei CDMA RNP&RNO Technologies Training Outline .........44

19 Microwave RNP ..................................................................................................................................................46

19.1 Huawei Certified Network Associate-Huawei Microwave RNP Technologies Training Outline .................46

19.2 Huawei Certified Network Professional-Huawei Microwave RNP Technologies Training Outline .............47

20 Site and Power System .......................................................................................................................................48

20.1 Huawei Certified Network Associate- -Huawei Site and Power System Technology and Device Training

Outline 48

21 Hybrid Power Supply ..........................................................................................................................................49

21.1 Huawei Certified Network Associate- Huawei Hybrid Power Supply Technology and Device Training

Outline 49

22 Hardware Installation Supervision (excluding RF products) ..................................................................................49

22.1 Huawei Certified Network Associate-Hardware Installation Supervision (excluding RF products) Training

Outline 49

23 Hardware Installation Supervision (including RF products) ...................................................................................50

23.1 Huawei Certified Network Associate-Hardware Installation Supervision (including RF products) Training

Outline 50


1 IP Technology Certification Training

1.1 HCDA-HNTD (Huawei Certified Datacom Associate-HuaWei

Networking Technologies and Device) Training

Training Path

Target Audience

This program is intended for those who are to be

certified by HCDA exam

Prerequisites

Be familiar with Windows operating system

Know the basic function and conception of

computer network

Objectives

On completion of this program, the participants will

be able to:

Describe the hierarchical structure of IP

network and the function of each layer

Describe Ethernet evolution and relative

technology

Outline network security and firewall concepts

Describe TCP/IP model, the function of each

layer, the function and the working principle of

some common protocols

Describe ICMP working principle

Describe Router and Switch working principle

Describe the basic principle and configuration

of VLAN, STP, VRRP, Static Route, RIP, OSPF,

PPP, Frame Relay

Design IP addresses with IP address

subnetting technology

Apply ping, tracert in network maintenance and

basic troubleshooting

Configure IP address, VLAN, VRRP, Static

Route，RIP，OSPF in VRP platform

Locate and handle the simple fault

Choose Huawei routers for each layer of IP

network

Duration

8 working days

Class Size

Min 6，max 12

HCDA-HNTD (Huawei Certified Datacom

Associate-Huawei Networking Technologies

and Device)

Lecture, Hands-on exercise

8 d ODC01


1.2 HCDP-BCRN (Huawei Certified Datacom Professional-Building

Carrier Routing Network) Training

Training Path

Target Audience


certified by the HCDP-BCRN exam

Prerequisites

Have got the HCDA certification or have

equivalent technical level

Objectives


be able to:

Flexibly apply the VLSM technique to design IP

addresses

Flexibly apply the CIDR technique to aggregate

the routes

Describe the IPv6 basic packets and the IPv6

address structure

Describe the basic protocol of IPv6 (ICMPv6,

ND, IPv6 address allocation protocol)

Describe the working principle of OSPFv2/v3

routing protocol

Describe several OSPF special areas

Troubleshoot OSPF neighbor relationship

failures and routing failures

Describe the working principle of ISIS routing

protocol in IPv4 and IPv6

Troubleshoot ISIS common neighbor relations

failure and routing failures

Configure OSPF and ISIS in VRP platform to

realize the IP connectivity of the large network

Describe the working principle of BGP and

MP-BGP for IPv6

Configure BGP/MP-BGP for IPv6 in VRP

platform and use BGP route attributes and

route policy to select and filter routing in large

network based on demand

Describe the working principle and function of

BGP route reflector and confederation

Describe the BGP multi-homed basic concepts

and application scenarios

Troubleshoot the BGP peer establishtion

failures,routing learning failures and path

selection failures

Flexibly apply the common route selection

tools(Access control

list,ip-prefix,as-path-filter,community-filter,route

-policy)

Describe the working principle of multicast

protocol(IGMP,PIM-SM,PIM-DM)

Configure IGMP/PIM-SM/PIM-DM in VRP

platform

Describe NE5000E/NE5000E-X16 series

hardware features

Describe NE80E/NE40E and NE40E-X series

hardware features

Select the appropriate Huawei middle and high

end routers based on the device performance

and service requirement to build the large

network and deploy the service

Locate and remove routing problems in large

scale IP network

Duration

9 working days

Class Size

Min 6，max 12

HCDP-BCRN (Huawei Certified Datacom

Professional-Building Carrier Routing Network)


9 d ODC02


1.3 HCDP-BCAN (Huawei Certified Datacom Professional-Building

Carrier Access Network) Training

Training Path

Target Audience


certified by HCDP-BCAN exam

Prerequisites



Objectives


be able to:

Describe the working principle of VLAN, GVRP,

QinQ, STP, RSTP, MSTP

Describe the working principle of PPP, PPPoE,

IPoE, IPoEoVLAN

Configure VLAN, GVRP, QinQ, STP, RSTP,

MSTP in VRP platform

Apply VLAN, GVRP, QinQ to access network to

implement user isolation and service

transportation

Apply STP, RSTP, MSTP in access network to

avoid loop

Deploy PPPoE, IPoE, IPoEoVLAN in access

network

Perform the troubleshooting about VLAN,

GVRP, QinQ, STP, RSTP, MSTP, PPPoE, IPoE,

IPoEoVLAN in access network

Choose appropriate Huawei switches and

BRAS devices in access network deployment

Duration

6 working days

Class Size

Min 6，max 12

HCDP-BCAN (Huawei Certified Datacom

Professional-Building Carrier Access Network)


6 d ODC03


1.4 HCDP-BITN (Huawei Certified Datacom Professional-Building IP

Telecom Network) Training

Training Path

Target Audience


certified by the HCDP-BITN exam

Prerequisites



Objectives


be able to:

Describe the features and performance of IP

bearer network

Describe the basic principle of MPLS

Describe the basic process of MPLS data

forwarding

Describe the basic concepts and principles of

the MPLS LDP

Description the MPLS LDP label management

mechanism and the loop protection mechanism

Configure MPLS LDP in VRP platform

Describe the basic concepts and basic

principles of the MPLS BGP VPN

Configure the MPLS BGP VPN in VRP platform

to realize the connectivity of the different sites

Configure the MPLS BGP VPN in the single

domain of the large IP bearer network to realize

private network users to access Internet

Master the troubleshooting methods of the

MPLS BGP VPN in control plane and data

plane

Describe the working principle and the four

components of MPLS TE

Configure MPLS TE in VRP platform

Describe the basic concepts of QoS and the

different QoS models

Describe the IP QoS technologies, such as

classification and marking,traffic policy and

shaping,congestion management and

avoidance,link efficiency mechanisms,etc

Describe the basic principle of the common HA

technologies, such as NSR, BFD, protection

switching technologies and VRRP

Duration

7 working days

Class Size

Min 6，max 12

HCDP-BITN (Huawei Certified Datacom

Professional-Building IP Telecom Network)


7 d ODC04


1.5 HCIE (Huawei Certified Internetwork Expert-Improve Carrier Network

Performance) Training

Training Path

Target Audience


certified by the HCIE exam

Prerequisites

Have got the HCDP certification or have the

equivalent technical knowledge level

Objectives


be able to:

Describe NE5000E/80E/40E advanced routing

features

Configure NE5000E/80E/40E advanced routing

features

Troubleshoot NE5000E/80E/40E advanced

routing features

Describe MAN typical network structure and

routing design features

Deploy routing protocol in MAN

Optimize routing protocol deployment in MAN

Troubleshoot the typical Failure of routing

protocol in MAN

Describe NE5000E/80E/40E advanced MPLS

L3VPN and L2VPN features

Configure NE5000E/80E/40E advanced MPLS

L3VPN and L2VPN features

Troubleshoot NE5000E/80E/40E advanced

MPLS L3VPN and L2VPN features

Describe IGMP principle and configuration

Describe PIM-SM principle and configuration

Describe PIM-SSM principle and configuration

Analyse MSDP basic working principle

Describe MSDP RPF detection

Describe MSDP application

Describe Multicast VPN function and technical

solution

Describe MD VPN concepts and working

principle

Advanced MPLS VPN Features Principle

and Configuration

ODC06 7 d

ODC07 Lecture, Hands-on exercise 1 d

QoS Features Principle and Configuration


ODC10

BRAS Access Service Features and

Realization

2 d Lecture, Hands-on exercise

IP MAN Design and Service Deployment


Lecture, Hands-on exercise 2 d ODC09

HA Features and Configuration

Advanced Routing Features Principle and

Configuration

Multicast Features Principle and Configuration



ODC05 2 d

IP Bearer Network Design and Service

Deployment

Lecture, Hands-on exercise 4 d

ODC13

ODC12

HCIE Simulation Lab Examination

exercise 2 d


Configure and troubleshoot MD VPN

Describe the QoS technology

Configure QoS in the NE series routers

Analyse and troubleshoot the common faults of

QoS configuration in the NE series routes

Describe the HQoS working principle in

NE5000E80E40E

Describe the HQoS scheduling process in

NE5000E80E40E

Describe the HQoS realization and application

Describe HA basic concepts and HA

classification

Describe BFD principles and typical

applications

Describe NSR principle

Describe the various protection switching

technology and in NE5000E80E40E product

Describe end-to-end HA features realization in

IP bearer network

Describe ME60&ME60-X series products

hardware

Describe ME60&ME60-X series products

Features

Describe the function of BRAS related

components

Analyse the ME60 PPP service working

process

Analyse the ME60 IP service working process

Analyse the ME60 Leased line service working

process

Describe the ME60 Multicast Feature and Realization

Describe IGP deployment in MAN

Describe IGP fast convergence deployment in

MAN

Configure and adjust OSPF/ISIS in MAN

Describe BGP deployment in MAN

Describe BGP RR deployment in MAN

Describe route control and route selection in IP

MAN

Configure and adjust BGP in MAN

Describe the devices and interfaces of core

network

Describe the solutions of IP bearer network

access part

Configure HA features of IP bearer core

network

Describe the fast convergence of routing

protocols

Describe the MPLS TE FRR and VPN FRR

technologies of IP bearer network backbone

Describe the GR technologies of IP bearer

network

Configure IGP/BGP and VPN of IP bearer core

network

Configure fast detection technologies of IP

bearer network

Configure fast convergence of routing protocols

Configure MPLS TE FRR and VPN FRR

technologies of IP bearer network backbone

Configure GR technologies of IP bearer

network

Describe different QoS requirement of different

services in IP bearer network

Describe end to end QoS realization in IP

bearer network

Configure end to end QoS in IP bearer network

Help candidates to be familiar with examination

mode,examination rules, and examination

environment

Duration

25 working days

Class Size

Min 2，max 6


2 Cloud Computing Certification Training

2.1 HCNA-HCTD (Huawei Certified Network Associate- Huawei Cloud

Technologies and Device) Training

Training Path

Target Audience

This training program is intended for those who are

to take the HCNA certification exam.

Prerequisites

Be familiar IT foundation knowledge.

Objectives

After the completion of this program, participants

will be able to:

Describe Active Directory Service.

Describe Dynamic Host Configuration Protocol.

Describe Domain Name Service.

Describe the Linux File System Structure.

Performing Linux Directory Operations.

Performing Linux File Operations.

Administering User Account.

Performing System Resources Management.

Performing Basic Network Configuration.

Describe the hierarchical structure of an IP network and

the functions of each layer.

Describe Cloud Computing Use Cases.

Describe Cloud Computing Key Characteristics.

Describe the Basic Concepts of Server Virtualization.

Describe the Basic Concepts of Network Virtualization.

Describe the Basic Concepts of Storage Virtualization.

Describe the Basic Concepts of Cloud Storage.

Identify the Storage Access Protocols.

Describe the RAID Features.

Describe Backup and High Availability for Storage.

Describe the Position of Galax in SingleCLOUD.

Describe the Components of Galax.

Describe the Features of Galax.

Describe the Server Architecture.

Describe the Server PCBs.

Describe the Server Switch PCB.

Describe the Server Management PCB.

Describe the Features of Server.

Describe the Features of Storage Product.

Describe the Storage Architecture.

Describe the Storage Specification.

Describe the Features of Switch Product.

Describe the Switch Architecture.

Describe the Switch Specification.

Describe Galax8800 Operating System.

Performing System Login.

Performing System Management.

Performing Server Management.

Performing System Configuration.

Performing Virtualization Operations.

Viewing System Message.

Viewing System Alert.

Viewing System Log.

Understand the Management Port Features.

Performing Common Management Tasks.

Understand OceanStor Management Port Features.

Understand OceanStor Management Features.

Desktop Cloud Administration Training

5d Lecture, Hands-on

exercise

Fundamentals of Cloud Computing Training

2d Lecture DC02

DC05

IT Foundation for Cloud Computing Training (Optional)

2 d DC03



Performing Common OceanStor Management Tasks.

Understand Switch Management Port Features.

Understand Switch Management Features.

Performing Common Switch Management Tasks.

Describe VDesktop6000 networking.

Describe VDesktop6000 structure and functions.

Describe VDesktop6000 service flow.

Perform VDesktop6000 count management.

Perform VDesktop6000 asset management.

Perform VDesktop6000 DDC management.

Perform VDesktop6000 system backup.

Perform VDesktop6000 performance management.

Describe TCs Terminal Types.

Describe TCs Characteristics.

Understand TC Configuration and Management.

Duration

9 workdays ( 2 days, optional + 7 days)

Maximum Class Size

12 persons

3 LTE Certification Training

3.1 HCNA-LTE (Huawei Certified Network Associate — LTE) Training

Training Mode

Target Audience


to take the HCNA-LTE certification exam and those

who hope to learn about basic LTE/SAE principles

and Huawei LTE equipment.

Prerequisites

Be familiar with basic wireless communication principles

Objectives


will be able to understand:

Basic pinciple of LTE air interfaces

Huawei eNodeB product family and applications

Basic operation about Huawei eNodeB

Basic concepts of the EPC

LTE/EPC network architecture

Interfaces and protocols used in the EPC

EPC security mechanism

EPC QoS mechanism

Procedures of bearer establishment, update, and

release

Concepts and procedures related to EPC mobility

management

Concepts and procedures related to EPC session

management

Duration

6 workdays

Maximum Class Size

16 persons


HCNA-LTE (Huawei Certified Network

Associate-LTE) Training


3.2 HCNP-LTE (Huawei Certified Network Professional — LTE) Training

Training Mode

Target Audience


to take the HCNP-LTE certification exam and those

who hope to learn about detailed LTE principles

and Huawei LTE equipment.

Prerequisites

Be familiar with basic LTE principles

Objectives


will be able to:

Understand structure of LTE /EPC

Understand detailed principle of LTE air interface

Understand functions of different layers in LTE air

interface

Understand functions and procedures of X1/S2 interface

Understand typical procedures in LTE such as

handovers

Perform Operations for HUAWEI LTE eNodeB such as

managing eNodeB alarms, tracing signaling, manage

eNodeB software, managing real-time monitoring and

etc.

Perform initial configuration and reconfiguration of

HUAWEI LTE eNodeB

Perform eNodeB troubleshooting

Duration

10 workdays

Maximum Class Size

16 persons

10d Lecture, Hands-on exercise

HCNP-LTE (Huawei Certified Network

Professional-LTE) Training


3.3 HCNP-EPC (Huawei Certified Network Professional — EPC) Training

Training Mode

Target Audience


to take the HCNP-EPC certification exam and

those who hope to learn about detailed EPC

principles and Huawei EPC equipments.

Prerequisites

Be familiar with basic EPC principles

Objectives


will be able to:

Describe system structure and hardware structure of

USN9810

Perform software related installation and upgrade

procedure

Perform hardware operation and maintenance

Perform the routing operation and maintenance

including security management, system information

management, alarm management, trace management ,

data management, license management ,performance

management

Describe the functions of protocol stacks of different

interfaces

Perform configuration of USN hardware, System

Information, interworking with eNodeB, HSS, MME,

S-GW, DNS, NTP

Perform configuration of mobility management and

session management

Describe system structure and hardware structure of

UGW9811

Perform software related installation and upgrade

procedure

Perform hardware operation and maintenance.

Perform the routing operation and maintenance

including authorization management, system

information management, alarm management, trace

management ,log management, license

management ,patch management ,data backup and

restore

Perform data configuration of S1-U&S11,S5S8 and SGi

interfaces .Describe basic concept of VPN,APN and

charging

Perform configuration of VPN ,APN and charging

Describe the DPI principles ,content based charging

principles and PCC concepts

Perform configuration of the DPI function, service

control function and PCC

Describe HSS9820 product function and application

Perform HSS9820 configuration of subscription data.

Describe the steps of HSS9820 data configuration.

Perform HSS9820 hardware and system data

configuration.

Perform HSS9820 interface data configuration.

Duration

12 workdays


HCNP-EPC (Huawei Certified Network

Professional-EPC) Training


Maximum Class Size 16 persons

4 Access Network

4.1 Huawei Certified Network Associate-Huawei Access Network

Technologies and Device Training Outline

Training Mode

Target Audience

This training program is intended for those who

hope to learn about basic access network theory.

Prerequisites

Be familiar with windows operation system.

Know well about computer network

Understand basic data communication theory

Understand basic fiber communication theory

Objectives


will be able to:

Understand xDSL/ATM/GPON/EPON/DataCom theory.

Be familiar with hardware construction, features, board

types, functions and interfaces

Know how to install/commission/configure access

equipment hardware.

Perform upgrade task under CLI of equipment.

Be familiar with HSI、IPTV、VOIP acceptance test.

Understand basic theory of NMS and SNMP, can use

NMS add and monitor equipment.

Duration

11 workdays

Maximum Class Size

16 persons

4.2 Huawei Certified Network Professional-Huawei Access Network


Training Mode

Target Audience


expect to learn more about the Access network

commissioning, maintenance and troubleshooting

Prerequisites

Function well on maintenance and commissioning of

Huawei equipments


H Huawei Access Network Technologies and Device Training


Huawei Access Network Technologies and

Device Training


Be familiar with access network communication theory

Objectives


will be able to:

Be familiar with HSI、IPTV、VOIP test item and test

function.

Be familiar with problem locating on

xDSL/ATM/GPON/EPON

Be familiar with problem maintenance of access network

products.

Perform data plan and network design for FTTx.

Be familiar with the typical solutions for Access Network

migration and the usage of the migration tools

Be familiar with NMS installation, basic NMS service

configuration, NMS operating system and basic

database commands for troubleshooting of access

products.

Duration

13 workdays

Maximum Class Size

16 persons

5 Optical Network

5.1 Huawei Certified Network Associate-Huawei Optical Network


Training Mode

Target Audience


want to take the HCNA certification exam and

those who hope to learn about basic optical

network principles .

Prerequisites

Be familiar with windows operation system.

Know well about computer network

Understand basic data communication theory

Understand basic fiber communication theory

Objectives


will be able to:

Understand SDH/WDM/data communication theory.

Be familiar with hardware construction, features, board

types, functions and interfaces

Know how to install/commission/configure optical

equipment hardware.

Understand DC tool, board-level loading and simulation

package loading of software.

Be familiar with MSTP/HMSTP/WDM acceptance test.

Understand basic theory of NMS and SNMP, can use

NMS add and monitor equipment.

Duration

15 workdays

Maximum Class Size

16 persons

5.2 Huawei Certified Network Professional-Huawei Optical Network



Huawei Optical Network Technologies and

Device Training


Training Mode

Target Audience


want to take the HCNP certification exam and

personnel who expect to learn SDH and WDM

network commissioning, maintenance and network

reconstruction

Prerequisites

Function well on maintenance and commissioning of

huawei equipments

Be familiar with optical network communication theory

Objectives


will be able to:

Be familiar with MSTP/WDM test item and test function.

Be familiar with OAM/QoS feature and function of MSTP

Be familiar with problem locating on SDH/WDM

Be familiar with problem maintenance of optical network

products.

Be familiar with data collection and basic service

planning of optical product.

Be familiar with NMS installation, basic NMS service

configuration, NMS operating system and basic

database commands for troubleshooting of optical

products.

Duration

10 workdays

Maximum Class Size

16 persons

6 Microwave Product

6.1 Huawei Certified Network Associate-Huawei Microwave


Training Mode

Target Audience


to take the HCNA-HMTD certification exam and

those who hope to learn about Huawei microwave

equipment operation and maintenance.

Prerequisites

Be familiar with the Windows operating system.

Know basic functions of the computer network.

Objectives


will be able to:

Describe the concept and characters of digital

microwave communication.

Describe the theory and function of every parts in the

digital microwave system.

List the networking application for digital microwave

systems.

Describe the Ethernet basic knowledge.

Describe the main characteristics of OptiX RTN 600.

Describe the system structure, function and application

of every unit in RTN 600.

List out the 1+1 protection technology in OptiX RTN 600

hybrid microwave network.

Describe the main characteristics of OptiX RTN 900.

Describe the system structure, functions and application

of every unit in RTN 900.

Describe the networking application under PDH/SDH


Huawei Microwave Technologies and Device Training


Huawei Optical Network Technologies and Device Training


and hybrid microwave modes.

List out the protection technologies in OptiX RTN 900

network.

Describe the features and applications of the protection

technologies.

List out the installation procedure for RTN equipment.

Finish proper preparations before the commissioning.

Perform site commissioning of the OptiX RTN 900.

Perform system commissioning of the OptiX RTN 900.

Configure radio links of the OptiX RTN 900.

Configure TDM services of the OptiX RTN 900.

Configure Ethernet services of the OptiX RTN 900.

Configure SNCP/MSP/ERPS/LAG for OptiX RTN 900.

Outline the general safety precautions of OptiX RTN

900.

List the routine maintenance items of OptiX RTN 900.

Implement the maintenance operation of OptiX RTN

900.

Judge the common faulty in OptiX RTN 900.

Implement the software upgrade operation of OptiX

RTN 900.

Implement the data collection operation of OptiX RTN

900.

Monitor the RTN equipment via the NMS.

Duration

9 workdays

Maximum Class Size

16 persons

6.2 Huawei Certified Network Professional-Huawei Microwave


Training Mode

Target Audience


to take the HCNP-HMTD certification exam and

those who hope to learn Huawei microwave

equipment.

Prerequisites

Take the HCNA-HMTD certification

Objectives


will be able to:

Describe the classification of IP addresses.

Describe the basic principle of IP routing.

Describe the basic concepts of MPLS.

Describe the MPLS tunnel (LSP) creation procedure.

Outline the MPLS OAM functions.

Describe the basic concepts of PWE3.

Outline the typical PWE3 encapsulation format for TDM,

Ethernet and ATM services.

Outline the PWE3 application scenarios of OptiX RTN

900.

Outline the steps of RTN 900 service configuration in

packet plane.

Implement Ethernet service/CES service/ATM/IMA

services configuration in packet plane via NMS.

Implement QoS/OAM/Clock configuration via NMS.

Implement the Ethernet service test via smartbits.

Install the U2000 Single-Server System Software.

Describe the system structure of U2000.

Describe the general troubleshooting flow of OptiX RTN

900.

Outline the methods of faults analyzing and locating.

Perform the common troubleshooting for OptiX RTN

900.

Identifying Radio Link Faults.

Duration

7 workdays

Maximum Class Size

16 persons


Huawei Microwave Technologies and Device Training


7 Mobile Soft Switch

7.1 Huawei Certified Network Associate-Huawei Mobile Soft Switch


Training Mode

Target Audience

MSOFTX3000 Field Maintenance Technicians,

First Line Maintenance Technicians or Routine

Maintenance Technicians/Engineers

Prerequisites

None

Objectives


will be able to:

Outline the development of GSM and UMTS.

Describe the architecture of GSM and UMTS system.

Describe the Networking and Interfaces of GSM NSS

and UMTS R4.

Describe the fundamental of mobile softswitch

technology.

Describe basic call control flows in UMTS R4 network.

Describe various types of bearer establishment in

UMTS R4 network.

Describe basic calling flow in UMTS R4 network.

Describe the hierarchical structure of an IP network and

the functions of each layer.

Describe the MSOFTX3000 system structure, functions,

and key characteristics(CPCI).

Describe the function, indicators, ports and working

mode of each board(CPCI).

Explain the types and applications of different fibers and

cables(CPCI).

Describe the toggle switch in MSOFTX3000(CPCI).

Perform operation through LMT(CPCI).

Describe MSOFTX3000 data configuration method and

procedure(CPCI).

Edit the data configuration scripts of

MSOFTX3000(CPCI).

Perform hardware data configuration(CPCI).

GSM/UMTS Softswitch Fundamental

OWA02

1 d

Lecture

GSM/UMTS CS Commnication Flow

OWG3012

2 d

Lecture

MSOFTX3000 Basic Data Configuration

OWG24

4 d


MSOFTX3000 Routine Operation and Maintenance

OWG22

5 d


MSOFTX3000 Hardware System

OWG10

1 d Lecture

MSOFTX3000 Delta Training(ATCA)

OWG44

2 d

Lecture

UMG8900 Routine Operation and Maintenance

OWH22

2 d


UMG8900 Data Configuration

OWH30

2 d


UMG8900 Software&Patch Loading

OWH11

1 d


UMG8900 Hardware System

OWH10

1 d Lecture


Perofrm local office data configuration.

Perform the data configuration to MGW, RNC, HLR and

PSTN.

Understand the usage of common commands.

Perform system data backup and restoration.

Perform daily alarm and statistic management task.

Understand the operation flow of parts replacement and

implementing technical protection measures.

Perform MSOFTX3000 parts replacement and check

the components running status.

Manage tracing tasks.

Perform the routine operation and maintenance tasks

(daily, weekly and monthly).

Understand troubleshooting procedure and common

troubleshooting methods.

Perform common hardware, interfaces, service

troubleshooting.

Describe the MSOFTX3000 system structure, functions,

and key characteristics(ATCA).


mode of each board(ATCA).


cables(ATCA).

Describe the toggle switch in MSOFTX3000(ATCA).

Perform operation through LMT(ATCA).

Describe MSOFTX3000 data configuration method and

procedure(ATCA).

Edit the data configuration scripts of

MSOFTX3000(ATCA).

Perform hardware data configuration(ATCA).

Describe the UMG8900 system functions, structures

and key characteristics.


mode of each board.


cables.

Describe the toggle switch in UMG8900.

Perform operation through LMT.

Perform UMG8900 Software&Patch Loading

Describe the UMG8900 data configuration method and

procedure.

Edit the data configuration scripts for UMG8900.

Execute the data configuration script.

Perform the dynamic data configuration and

modification.

Perform UMG8900 system data, interfaces data and

resource data configuration.

Perform system data backup and restoration, execute

MML commands, etc.



Perform UMG8900 parts replacement and check the

components running status.


Monitor alarms of UMG8900.






troubleshooting.

Perform UMG8900 software&Patch reloading and path

upgrading

Duration

21 work days

Maximum Class Size

16 persons

7.2 Huawei Certified Network Professional-Huawei Mobile Soft Switch



Training Mode

Target Audience

Core network commissioning engineers, operation

and maintenance engineers, optimization

engineers

Prerequisites

At least two years experience of operation and

maintenance of GSM NSS/UMTS CS or other

telecommunication equipments

A basic knowledge of mobile communication and soft

switch principle

Objectives


will be able to:

Edit the data configuration scripts of MSOFTX3000.


modification.

Understand deeply number analysis concepts and

working principle in MSOFTX3000.

Perform number analysis configuration and testing task,

including call barring analysis, failure processing data,

equal access data, etc.

Understand deeply IN service concepts and processing

flow in MSOFTX3000.

Perform IN service configuration and testing task,

including DP data, SCP data, IN service data, IN

announcement data, etc.

Understand deeply IN service concepts and processing

flow in MSOFTX3000.

Perform IN service configuration and testing task,

including DP data, SCP data, IN service data, IN

announcement data, etc.

Understand deeply Dual-homing concepts, networking

modes and switchover modes in MSOFTX3000.

Use the emergency maintenance tools and platform,

and understand device and service emergency

maintenance procedure.

Perform complex hardware, interfaces, service

troubleshooting.

Describe BSSAP protocol stack and function.

Analysis main procedures of BSSAP (Paging, Initial MS

Message, Cipher Mode Control, Assignment, Handover,

Release, DTAP Message).

Describe Iu interface protocol stack and function.

Describe classification of RANAP messages.

Analysis Iu connection Management, RAB assignment,

SRNS Relocation

CS Domain MM, CC procedures in Iu Interfaces.

Perform protocol stack and main functions of SIGTRAN.

Analysis SCTP association establishment and close

flows.

Describe UA concepts introduction (AS, SG, IPSP, Entity,

Routing key).

Perform messages analysis of SCTP, M2UA, and

M3UA.

Describe H.248 Protocol stack and functions.

Perform message analysis of H.248 based on scenario.

Describe BICC protocol stack and functions.

MSOFTX3000 Emergency Maintenance

OWG36

1 d


MSOFTX3000 Troubleshooting

OWG38

2 d

Lecture, Hands-on exercise, Case

MSOFTX3000 Advanced Data Configuration

OWG30


MSS Signaling Analysis

OWA04

5 d

Lecture, Hand-on practice

MSC POOL Training

OWG62

5 d Lecture, Case-study

UMG8900 Emergency Maintenance& Troubleshooting

OWH34

1 d


UMG8900 Fault Location&Networking

OWH36

5 d

Lecture, Hands-on exercise, Case


Analysis key parameters of BICC.

Analysis BICC message.

Describe MSC Pool networking.

Describe principles related to the MSC Pool features.

(The load balancing of MSC Pool, Handover in MSC

Pool, Disaster tolerance in MSC Pool, Subscriber

migration in MSC Pool, A-Flex by the MGW, Managing

A-Interface Circuits on the MGW, Charging based on

Virtual MSC IDs or Location Areas).

Describe MSC Pool configuration flow overview.

Perform MSC Pool feature configuration in MSC Server

and MGW.

Perform MSC Pool configuration based on different

scenarios (NNSF implemented by RNC, NNSF

implemented by MGW, Restructure MSC Pool based on

current network).

Monitor MSC Pool Load in real time.

Operate performance report of the MSC Pool.

Perform migration of subscribers.

Perform MSC Pool configuration synchronization

between NE and M2000.

Perform end-to-end tracing of calls on the MSC Pool.


modification.

Check the data configuration correctness and validity.

Use the emergency maintenance tools and platform,

and understand emergency maintenance procedure.

Handle UMG8900 device and service fault and perform

emergency recovering.

Perform complex hardware, interfaces, signaling,

service networking troubleshooting.

Duration

21 workdays

Maximum Class Size

16 persons

8 NGN

8.1 Huawei Certified Network Associate-Huawei NGN Technologies and

Device Training Outline

Training Mode

OAX01 20 d Lecture, Hands-on exercise

Huawei NGN Primary Training


Target Audience


to take Huawei NGN Primary certification exam

and those who hope to learn about basic NGN

principles and Huawei NGN equipment.

Prerequisites



Objectives


will be able to:

Principle

Describe the basic concepts, system architecture,

services, networking and applications of NGN.

Outline the components, services, networking and

applications of Huawei U-SYS solution.

Explain the functions, features, applications, terms,

stack structure and messages of NGN protocols (MGCP,

H.248, SIP, SIGTRAN).

Product Introduction

Describe the network topology, services, functions,

system structure, board functions, board indicators,

networking, applications and technical specifications of

SoftX3000/UMG8900/SG7000/MRS6100/SE2300.

Describe the network topology, services and functions of

U-Path.

Basic Data Configuration

Perform the hardware and local office data configuration

of SoftX3000.

Perform the hardware data configuration, MGW data

configuration and IP bearer data configuration.

Perform the hardware data configuration of MRS6100.

Perform the hardware data configuration and local office

data configuration of SG7000.

Data Configuration & acceptance testing

Outline the service data configuration steps of

SoftX3000, and execute the common service data

configuration (charging data configuration, media

gateway data configuration, protocol data configuration,

SS7 signaling data configuration, routing data

configuration, trunk data configuration, number analysis

data configuration, subscriber data configuration).


UMG8900, and execute the common service data

configuration (TG data configuration, SG data

configuration).


MRS6100, and execute the system data configuration

and the voice file loading.

Outline the service data configuration steps of SG7000,

and execute the common service data configuration

(MTP data configuration, M3UA data configuration).

Outline the service data configuration steps of SE2300,

and execute the common service data configuration

(SNMP data configuration, signaling PROXY and media

PROXY data configuration).

Perform the software installation and the service

configuration of U-Path.

Maintenance & Troubleshooting

Perform the routine operation and maintenance of

SoftX3000 (operator authority management, database

backup and restoration, data consistent checking

between the host and BAM, log management, alarm

management, device management, media gateway

management, protocol and signaling management,

trunk circuit management, subscriber management, bill

management).


iGWB.


UMG8900 (database backup, log management, alarm

management, device management, protocol tracing,

service management).


MRS6100 (log management, alarm management,

device management, message tracing).


SG7000 (database backup, log management, alarm

management, device management, signaling tracing).


SE2300 (log management, alarm management, device

management, signaling PROXY and media PROXY

debugging).


U-Path (log management, system status browsing, and

bill management).


Perform the common troubleshooting of NGN

equipment.

Duration

20 workdays

Maximum Class Size

16 persons

8.2 Huawei Certified Network Professional-Huawei NGN Technologies

and Device Training Outline

Training Mode

Target Audience


have pass the Huawei NGN Primary certification

exam and those who hope to learn about in-depth

NGN principles and Huawei NGN equipment.

Prerequisites

Successfully pass the Huawei NGN Primary certification

exam

At least a half year of experience in the operation and

maintenance of NGN

Objectives


will be able to:

Principle

Explain the command parameters and call processing

procedure of NGN protocols.

Describe the principle, application of NGN dual home.

Describe the NGN C4 and C5 office migration solution.

Product Introduction

Describe the working principle and service processing

procedure of SoftX3000.

Describe the principle, processing procedure, operation

and original bill format of NGN charging system

Describe the system structure and configuration of

iGWB.

List the means of improving voice quality of NGN.

Describe the working principle and service processing

procedure of UMG8900.

Describe the working principle, announcement principle

and service processing procedure of MRS6100.

Basic Data Configuration

Execute the service data configuration of SoftX3000

(number changing data configuration, call barring data

configuration).

Perform the language conversion of voice and voice

loading of MRS6100.

Execute the service data configuration of SG7000 (MTP

load sharing data configuration).

Data Configuration & acceptance testing

Perform data planning and data configuration of NGN

dual home.

Perform the NGN C4 and C5 office migration operation.

Maintenance & Troubleshooting

Perform the routine maintenance of NGN dual home.

Perform the common problem analysis and processing

of NGN protocols.

Perform the troubleshooting of NGN network.

Duration

11 workdays

Maximum Class Size

16 persons

OAX02 11 d Lecture, Hands-on exercise

Huawei NGN Secondary Training


9 MGW&SBC

9.1 Huawei Certified Network Associate-Huawei MGW&SBC


Training Mode

Target Audience

UMG8900&SBC Field Maintenance Technicians,

First Line Maintenance Technicians or Routine

Maintenance Technicians/Engineers

Prerequisites

At least one year experience of operation and

maintenance of GSM NSS/UMTS CS or other

telecommunication equipments

Being familiar with Windows operation

A basic knowledge of mobile communications

Objectives


be able to:

Know about WCDMA Core Network Evolution and main

versions;

Understand the network architecture and function entity

of GSM/R99/R4,and the interface and protocol;

Understand bearer and control separated

architecture;Understand the function and application of

MSOFTX3000 and UMG8900; Understand the

definition and architecture of NGN and every layer's

functions;Konw about the location of UMG8900 in NGN.

Understand SIGTRAN's function,M3UA's basic

concepts、function and application;

Understand M2UA's concepts、protocol stacks and main

parameters;

Understand UMG8900's TDM bearer and data

configuration of SG(MTP3-M3UA);

Understand SIGTRAN's function,M3UA's basic

concepts、function and application;

Understand M2UA's concepts、protocol stacks and main

parameters;

Understand UMG8900's TDM bearer and data

configuration of SG(MTP3-M3UA);

Describe the UMG8900 system functions, structures

and key characteristics.


mode of each board.


cables.

Describe the toggle switch in UMG8900.

Perform operation through LMT.

Perform UMG8900 Software&Patch Loading

Describe the UMG8900 data configuration method and

procedure.

Edit the data configuration scripts for UMG8900.

Execute the data configuration script.


modification.

Perform UMG8900 system data, interfaces data and

resource data configuration.

NGN/GSM/UMTS Softswitch Fundamental

OWA02

1 d

Lecture

UMG8900 Data Configuration

OWH30

2 d


UMG8900 Software&Patch Loading

OWH11

1 d


UMG8900 Hardware System

OWH10

1 d Lecture

UMG8900 Routine Operation and Maintenance

OWH22

2 d


SE2600 Operation and Maintenance


OZD04


Perform system data backup and restoration, execute

MML commands, etc.



Perform UMG8900 parts replacement and check the

components running status.


Monitor alarms of UMG8900.






troubleshooting.

Perform UMG8900 software&Patch reloading and path

upgrading

Describe related concepts of SBC, working principle of

full proxy.

Describe main functions and features of SE2600 in IMS

network.

Describe call flow analysis.

Describe hardware structure of SE2600.

Perform interconnection data configuration.

Perform service data configuration.

Perform maintenance tasks for SE2600.

Perform SE2600 troubleshooting.

Duration

9 working days

Class Size

max 16


10 USC

10.1 Huawei Certified Network Associate-Huawei USC Technologies


Training Path

Target Audience

SingelSDB GUHLR9820 project installation and

configuration Engineers;

Prerequisites

A basic knowledge of mobile communication

Objectives


be able to:

Understand System Structure and Principles:

Describe the architecture of Huawei SingleSDB system

Describe the Networking and Interfaces of Huawei

SingleSDB

Describe the hardware, logical structure of Huawei

SingleSDB

Describe the typical configurations of SingleSDB

products

List key advantages of Huawei SingleSDB products

Describe HLR9820 hardware structure

Describe all kinds of Buses in ATCA Platform

Describe HLR9820 boards function

Describe connections and cables

Perform System Installation:

Describe processes of System installation

Describe how Huawei SingleSDB system connected

internal and external

Perform Huawei HLR9820 system installation

Perform Huawei HLR9820 system debugging

Perform system data configuration:

Describe data configuration principles and steps

Describe GSM/UMTS network numbering scheme

Describe HLR9820 system hardware& software

configuration procedure and reliable specifications

Describe HLR9820 basic concept: Site, NE, Cluster,

Node and module

Perform Hardware Data Configuration

Perform Local Office Data Configuration

Perform Signaling Data Configuration

Understand HLR9820 Subscriber Management

Procedure:

Describe UMTS Common Service Feature

Perform operation of templates to manage subscribers’

profiles

Perform operation to manage subscribers’ profiles

Describe the HLR9820 subscriber management method

and procedure

Perform operation to modify services according to the

requests from subscribers

Perform Subscriber data management

Perform Operator Management

Perform Network maintenance

Perform operation to Check subscribers’ profiles based

on different fault phenomena

HLR9820V900R006 System Introduction

2 d

Lecture

HLR9820V900R006 System Installation

3.5 d


HLR9820V900R006 Data Configuration

3.5 d


HLR9820V900R006 Subscriber

Data Managemen

1d



Duration

10 working days

Class Size

Min 5，max 15

10.2 Huawei Certified Network Professional-Huawei USC Technologies



Training Mode

Target Audience

Senior Technical Support Engineer;

Prerequisites

Successful completion of the program SingleSDB（G/U

HLR9820）Engineering Training

Or At least one year experience of HLR9820 operation

Objectives


be able to:

Describe the internal networking and IP planning of

HLR9820

Describe Redundancy Principle and Key parameters of

configuration

Describe DS Principle Data synchronization,

consistency and Replication Principle

Describe Baseline establishment, increment data

synchronization, recovery operation

Perform LMT MML Operation and HLR9820 routine

maintenance

Perform Security Management, Alarm Operations,

Message Tracing and Performance Operations

Perform Database backup and restoration

HLRV9 Equipment fault information collection and

processing

Procedures and methods of fault location and

troubleshooting: Use the system maintenance tools

Perform system management, cluster management,

disk management and Database management

Duration

4 working days

Class Size

Min 5，max 15.

11 SG

11.1 Huawei Certified Network Associate-Huawei SG Technologies and

Device Training Outline

HLR9820V900R006 IP Resource Planning and Redundancy Solution

0.5 d

Lecture

SingleSDB Redundancy System

Commissioning

0.5 d


SingleSDB Operation and Maintenance

3.5 d


SingleSDB Maintenance and

Troubleshooting

1d



Training Mode

Target Audience


to take Huawei Certified Network

Associate-Huawei SG Technologies and Device

certification exam and those who hope to learn

about basic SG7000 principles and Huawei

SG7000 equipment.

Prerequisites



Objectives


will be able to:

Describe the basic concepts, architecture, MTP

functions of SS7 Signaling System and signaling

network.

Describe the basic function of SCCP.

State the format of SCCP message and the meaning of

the message which are often used.

Describe the basic concept of SIGTRAN, the structure

and signaling procedures of M2PA/M3UA.

Describe SG7000 system structure and hardware

architecture, including the cabinet, frame, board and the

performance features of SG7000.

Describe SG7000 logical architecture and signaling

flow.

Configure the hardware data, narrowband link data and

broadband link data.

Implement the common operation of maintenance such

as message tracing, log management, alarm

management and link management.

Perform SG7000 client software installation.

Perform SCCP and M2PA data configuration of

SG7000.

Duration

5 workdays

Maximum Class Size

16 persons

11.2 Huawei Certified Network Professional-Huawei SG Technologies


Training Mode


Huawei SG Technologies and Device Training


Huawei SG Technologies and Device Training


Target Audience


have pass the Huawei Certified Network

Professional-Huawei SG Technologies and Device

certification exam and those who hope to learn

about in-depth SG7000 principles and Huawei

SG7000 equipment.

Prerequisites

Successfully pass the Huawei SG7000 Primary

certification exam

At least a half year of experience in the operation and

maintenance of SG7000

Objectives


will be able to:

Describe the basic principle of MNP service.

Perform SG7000 MTP loadsharing data configuration.

Perform SG7000 SCCP loadsharing data configuration.

Describe the troubleshooting method of SG7000.

Perform information collection of SG7000 trouble.

Locate the hardware trouble, link trouble and SCCP

layer trouble.

Duration

2 workdays

Maximum Class Size

16 persons

12 GSM

12.1 Huawei Certified Network Associate-Huawei GSM Technologies


Training Mode


Target Audience


to take the HCNA certification exam and those who

hope to learn about basic GSM principles and

Huawei GSM equipment.

Prerequisites



Objectives


will be able to:

Principles

1.Understandable of the basic principle of GSM and

GPRS technology

2.Familiar with GSM system architecture and the

wireless network interface

Product knowledge

1.Master BSC6900 (GSM) system overview, hardware

architecture and product specifications

2.Master BTS3900/DBS3900 (GSM) hardware

architecture and module functions

3.Master typical configuration of BTS3900/DBS3900

(GSM)

4.Master BTS3900/DBS3900 (MBTS) hardware


5.Master typical configuration of BTS3900/DBS3900

(MBTS)

Engineering survey and hardware installation

1.Master the engineering survey approaches of site

controller and site

2.Master the installation design approaches of site

controller and site

3.Master the hardware installation approaches of site

controller and site (including feeder system, monitoring,

and other peripherals)

Software Commissioning

1.Master the remote and local commissioning

approaches of the site

2.Master the site integration approaches

3.Master the site service testing approaches

4.Master the using methods of testing tool and know the

meaning of testing indicators

Acceptance testing

1.Master the hardware quality standard

2.Master the acceptance approaches of a single-site

(including service testing)

Maintenance and troubleshooting

1. Master the site operation& maintenance approaches

2.Capable of independently dealing with hardware

replacement and information collection of site

3.Capable of independently dealing with site problems

and emergency recovery on-site

Duration

11 working days

Maximum Class Size

20 persons

12.2 Huawei Certified Network Professional-Huawei GSM Technologies


Training Mode


GSM Huawei Certified Network

Associate-Huawei GSM Technologies

and Device


Target Audience


to take the HCNP certification exam and those who

hope to learn about basic GSM principles and

Huawei GSM equipment.

Prerequisites



Objectives

Compare with “Huawei Certified Network

Associate-Huawei GSM Technologies and Device

Training”, the objectives added are shown as

follows. After the completion of this program,

participants will be able to:

Principles

1.Understandable of the signaling process of GSM

system

Product knowledge

1.Master CME configuration tool principles and

operational guidance

2.Understandable of M2000 system architecture and

master the operation of client

Software Commissioning

1.Capable of independently finishing data configuration

of site controller and site through WebLMT and CME

2.Master the software commissioning approaches of the

controller

3.Capable of independently finishing new site

integration through M2000

Acceptance testing

1.Master the acceptance approaches of controller

Software Upgrade

1.Master the local upgrade approaches of the site

2.Master the remote upgrade approaches of the site

Maintenance and troubleshooting

1.Master the controller operation& maintenance

approaches

2.Capable of independently dealing with hardware

replacement and information collection of controller

3.Capable of independently dealing with controller

problems and emergency recovery on-site

4. Capable of independently finishing network

inspection through NIC and OMSTAR tools

Duration

14 working days

Maximum Class Size

20 persons.

13 WCDMA

13.1 Huawei Certified Network Associate-Huawei WCDMA


Training Mode

Target Audience



hope to learn about basic WCDMA principles and

Huawei WCDMA equipment.

Prerequisites

Be familiar with the Windows operating system. 9 d Lecture, Hands-on

exercise

HCNA-WCDMA Huawei Certified

Network Associate-Huawei WCDMA

Technologies and Device


Huawei Certified Network

Professional-Huawei GSM Technologies

and Device



Objectives


will be able to:

Describe the basic principle of WCDMA technology

Describe WCDMA system architecture and the wireless

network interface

Describe BSC6900 (WCDMA) system , hardware

architecture and product specifications

Describe BTS3900/DBS3900 (WCDMA) hardware


Outline typical configuration of BTS3900/DBS3900

(WCDMA)

Describe BTS3900/DBS3900 (MBTS) hardware



(MBTS)

Complete engineering survey of site controller

Complete engineering survey of site

Complete installation design of site controller

Complete installation design of site

Complete hardware installation of site controller

Complete hardware installation of site (including feeder

system, monitoring, and other peripherals)

Complete remote/local commissioning of the site

Complete site integration

Complete site service testing

Perform testing tool and testing indicators

Hardware installation check

Acceptance of a single-site (including service testing)

Hardware Replacement

Information collection

Deal with problems on site

On-site emergency recovery

Duration

9 working days

Maximum Class Size

20 persons

13.2 Huawei Certified Network Professional-Huawei WCDMA


Training Mode

Target Audience



hope to learn about basic WCDMA principles and

Huawei WCDMA equipment.

Prerequisites



Objectives


will be able to:

Describe WCDMA wireless network architecture

Describe the signaling process of the WCDMA system

Describe BTS3900/DBS3900 (MBTS) hardware

Describe BTS3900/DBS3900 (MBTS) architecture and

module functions


(MBTS)


HCNP-WCDMA Huawei Certified

Network Professional-Huawei WCDMA

Technologies and Device


Outline CME configuration tool principles and platform

Outline CME configuration tool operation

Outline the M2000 system architecture and operation

Outline function of the M2000 system

Perform data configuration for site

Perform data configuration for site controller

Complete the process of site data configuration

Complete the process of site controller data

configuration

Perform software commissioning of the controller

Describe the process of software commissioning

Perform new site integration through M2000

Describe the process of new site integration

Describe the process of remote upgrade of the site

Describe the process of local upgrade of the site

Complete remote upgrade of the site

Complete local upgrade of the site

Complete hardware replacement

Complete Information collection for controller

Deal with problems on site for controller

Complete On-site emergency recovery for controller

Duration

13 working days

Maximum Class Size

20 persons.

14 CDMA

14.1 Huawei Certified Network Associate-Huawei CDMA Technologies


Training Mode

Target Audience



hope to learn about basic CDMA principles and

Huawei CDMA equipment.

Prerequisites



Objectives

Principles (1 day)

1.cdma2000 1X & 1xEV-DO basic technology (CDMA

technology development road signpost、f cdma2000

1X/1xEV-DO technical characteristics and network

structure, key technology of cdma2000 1X and UM

channel Introduction、EVDO new technologies and UM

channel Introduction) ;

2.the technical characteristics and network architecture

of the the Trustar digital trunking communication

system ;

Product knowledge (4 days)

1.BSC6680/BSC6600 / RAC6610/MSE9830 controller

and bts products(hardware components, the basic

configuration rules and board function.);

2,.the meaning of the BSC6680/BSC6600 /

RAC6610/MSE9830 controller and bts products, the

meaning of it’s board indicator light;

3.BTS3900/BTS36xx series of CDMA base station

antenna and feeder cable introduction (basic knowledge

of radio waves, the basic principles of antenna radiation

of electromagnetic waves, introduced the concept of the

antenna transmission cable, the base station antenna

and feeder cable systems) ;

4.the introduction of complementary products (room

environment of the project site, the power system ,

alarm boxes, etc.) ;

5.the controller and bts products survey content and

survey Note;

6.the bts hardware distribution, delivery rules, methods,

7~7.5 d Lecture, Hands-on exercise

Huawei CDMA Technologies and Device

Training


understanding Huawei BOQ and the meaning of the

packing list;

7.controller and base station hardware installation and

the Power On Self Test;

Data configuration and commissioning

Acceptance Test (1 day)

1.the BTS hardware installation quality inspection

content and standards;

2.Grasp the power meter, sitemaster ,test terminal use

method;

Chinese Edition adds the following:

1.the BSC hardware installation quality inspection


Maintenance and Troubleshooting (1day)

1.Grasp the replacement method and operation

procedure of BSC6680/BSC6600/RAC6610/MSE9830

board、frame etc.

2.Grasp the replacement method and operation

procedure of BTS36xx/39xx serial bts board、BBU etc.

Duration

7～7.5 working days （no practice）

Maximum Class Size

20 persons


14.2 Huawei Certified Network Professional-Huawei CDMA


Training Mode

Target Audience



hope to learn about basic CDMA principles and

Huawei CDMA equipment.

Prerequisites



Objectives

Principles (1.5 days +1 day)

1.cdma2000 1X & 1xEV-DO basic technology (CDMA

technology development road signpost、f cdma2000

1X/1xEV-DO technical characteristics and network

structure, key technology of cdma2000 1X and UM

channel Introduction、EVDO new technologies and UM

channel Introduction) ;

2.the technical characteristics and network architecture

of the the Trustar digital trunking communication

system ;

3.Grasp transmission fundamentals (TCPIP protocol

and subnetting, Ethernet / VLAN / VRRP / Routing

Fundamentals) ;

Product knowledge (4 days)

1.BSC6680/BSC6600 / RAC6610/MSE9830 controller

and bts products(hardware components, the basic

configuration rules and board function.);

2.the meaning of the BSC6680/BSC6600 /

RAC6610/MSE9830 controller and bts products, the

meaning of it’s board indicator light;

3.BTS3900/BTS36xx series of CDMA base station

antenna and feeder cable introduction (basic knowledge

of radio waves, the basic principles of antenna radiation

of electromagnetic waves, introduced the concept of the

antenna transmission cable, the base station antenna

and feeder cable systems) ;

4.the introduction of complementary products (room

environment of the project site, the power system ,

alarm boxes, etc.) ;

5.the controller and bts products survey content and

survey Note;

6.the bts hardware distribution, delivery rules, methods,

understanding Huawei BOQ and the meaning of the

packing list;

7.controller and base station hardware installation and

the Power On Self Test;

Data configuration and commissioning (2 days

+1 day)

1.the BTS data and software loading process and

methodology;

13.5~16 d Lecture, Hands-on exercise

Huawei CDMA Technologies and Device


2.the BTS data configuration;

3.the BTS basic commissioning procedure;

4.the meaning of the BTS of the Engineering Indicators

(VSWR, RSSI、output power) and test methods，Finish

the BTS troubleshooting and quality inspection under

the guidance. ;

5.the BTS environment alarm configuration, debugging;

6.IP RAN network form and IPRAN BTS data

configuration;

Chinese Edition adds the following (2 days + 2

days)

1.BSC6680 controller internal signals (signaling, traffic)

processes procedure, the basic rules of the system

configuration;

2.Operation and maintenance system of BSC6680

(CDMA BSC6680 maintenance system agencies,

system networking, maintenance system software

structure, the internal IP network, IP address planning) ;

3.BSC6680 data configuration (the basic configuration

of BSC6680 system,, the file loading procedure, the

CDMA BSC6680 hardware, clock, interface, cell, carrier,

and cdma2000 1X/1xEV-DO business data

configuration) ;

4.BSC6680 signaling procedure(voice, data services,

short message, handoff signaling process) ;

5.the BSC data configuration under IP RAN network;

Acceptance Test (1 day+ 0.5 days)

1.the BTS hardware installation quality inspection


2.the BTS software installation quality inspection


3.the LMT maintenance method of RSSI,VSWR,

Transmit power tracing;

4.Single BTS acceptance range and standard;

5.Grasp the power meter, sitemaster ,test terminal use

method;

6.the acceptance range and standard of BTS basic

characteristics;

Chinese Edition adds the following: (1 day+0.5

days)

1.the BSC hardware installation quality inspection


2.the BSC software installation quality inspection


3, the LMT maintenance method of signal tracing;

4,Single BSC acceptance range and standard;

5, the acceptance range and standard of BSC basic

characteristics;

Maintenance and Troubleshooting (2 days + 0.5

day)

1.Grasp the replacement method of spare parts, clear

procedure key points;

2.Familiar with some of the commonly used test tools

(sitemaster, power meter, test phone, etc.)

3.Familiar with the daily operation &maintenance of the

36xx/39xx Series BTS and

RAC6610/BSC6600/BSC6680 ,basic information

collection methods, analysis and process the common

fault alarm base on online help;

4.Grasp MSE9830 board replacement methods,

procedure and information collection methods;

5.To understand the common fault scenarios of the

36xx/39xx Series bts, to grasp the emergency fault

information collection and recovery measures, quickly

recovery according the guidance;

6.the use method of FMA tools

Duration

13.5~16 working days （no practice）

Maximum Class Size

20 persons.


15 Wimax

15.1 Huawei Certified Network Professional-Huawei Wimax


Training Mode

Target Audience


to take the Wimax certification exam and those

who hope to learn about basic Wimax principles

and Huawei Wimax equipment.

Prerequisites



Objectives


will be able to:

Describe OFDM/OFDMA Basics

Describe WiMAX Features

Describe WiMAX Applications

Describe WiMAX system networking

Outline each board function of DBS3900 WiMAX

Complete the inside connection of DBS3900

State the typical networking configuration

Describe WiMAX system networking

Outline DBS3900 WiMAX functions

Outline each board function of DBS3900 WiMAX

Complete the inside connection of DBS3900

State the typical networking configuration

Describe WiMAX Network Structure

Master the local operation and remote operation

Complete daily maintenance tasks

Complet the concept related to configuration

Management

Complet how to perform configuration Management

Finish basic data configuration for WiMAX DBS3900

Describe the two types of commissioning

Perform local commissioning

Perform remote commissioning

Describe How to install DBS3900 in site

Describe how to install Antena system

Finish bacis function Acceptance.

Can be done Deriver test

Complete daily maintenance tasks

Can be change board basicly

Duration

8 workdays

Maximum Class Size

16 persons


Huawei Certified Network Professional-Huawei Wimax Technologies and Device


16 GSM RNP&RNO

16.1 Huawei Certified Network Associate- Huawei GSM RNP&RNO

Technology Training Outline

Training Mode

Target Audience

This training program is intended for those who are to

take the HCNA GSM RNP&RNO certification exam.

Prerequisites

Skilled in windows operating system.

Capable of describing the basic functions of computer

network.

Skilled in using business softwares like office and

outlook.

Capable of describing the basic functions of mobile

communication.

Objectives

Principle：

Understandable of the GSM basic theories /wireless

transmission /telecomunicatios as well as attenna and

associated parameters.

Planning knowledges：

Familiar with radio transmission theoretics and the usual

transmission model.

Optimization knowledges：

Capable of independently writing the analysis of

electromagnetic interference, and providing preliminary

resolutions for the target area accordingly.

Capable of independently finishing site survey and

report upon request.

Capable of independently using related tools to survey

radio parameters and quality of antenna.

Capable of independently accomplishing DT/CQT test

(single site verification) by Genex Porbe, analyzing the

problems of DT/CQT by Genex Assistant and deliver

resolutions accordingly.

Capable of dealing with common customer’s complaint

by DT/CQT.

Familiar with the meaning and adjusting regulations of

commonly used Network Design parameters.

Duration

7 workdays

Maximum Class Size

16 persons

7 d Lecture,Hands-on

exercise


Associate-Huawei GSM RNP&RNO

Technologies Training


16.2 Huawei Certified Network Professional - Huawei GSM RNP&RNO

Technology Training Outline

Training Mode

Target Audience


to take the HCNP GSM RNP&RNO certification

exam.

Prerequisites



outlook .


communication.

Have qualifications for HCNA-Huawei GSM RNP&RNO

Technologies.

Objectives

Principle：

Familiar with GSM communication theory.

Master wireless network planning and optimazition

process.


Master the GSM coverage planning, capacity planning,

neighbor/frequency design, location area design,

parameters design and GPRS planning.

Master the related parameters and adjusting regulations

of Network Design.

Master the way of CW testing and related data

processing.

Master the corrective procedure of transmission model.


Master the RF optimazition & procedure, methods and

tools, capable of processing GSM radio network RF

optimazition.

Master the definition of traffic statistics and counter point

in the wireless side of GSM Network.

Master GSM common KPI analysis and network

problem solution, such as drop call, handover, voice

quality and data traffic.

Capable of independently completing network

optimazition reports and generating problem analysis

reports.

Duration

8workdays

Maximum Class Size

16 persons


exercise

Huawei Certified Network Professional-Huawei

GSM RNP&RNO Technologies Training


17 WCDMA RNP&RNO

17.1 Huawei Certified Network Associate-WCDMA RNP&RNO Training

Outline

Training Mode

Target Audience


to take the Huawei Certified Network

Associate-WCDMA RNP&RNO certification exam.

Prerequisites



outlook.


communication.

Objectives

Principle：

Understandable of the WCDMA basic theories, wireless

transmission, telecomunicatios, attenna and associated

parameters.


Master antenna selection.

Initial grasp of network planning and optimization

process, familiar with the site survey, RF Tuning

process.

Familiar with the theory of radio propagation and

common propagation models.


Independent output electromagnetic interference

analysis, and existence of the interference region is

given a preliminary settlement proposals.

Be able to independently asked to complete the site

investigation and reporting.

Be able to use the tools to verify the wireless working

parameters and the quality of the antenna and cable

correction.

Be able to independently use the Genex Probe,

completion of DT / CQT testing (including single-station

verification), Genex Assistant analysis of the problem in

the DT / CQT, the output of the corresponding solutions.

Deal with general customer complaints by DT / CQT.

Grasp the road test KPI the meaning and the testing

method, independent production test program and

complete.

Master the cell parameters to verify the method, familiar

with the meaning of the parameters and adjust the basis

of the common network rules.

Duration

7 workdays

Maximum Class Size

16 persons

17.2 Huawei Certified Network Professional-WCDMA RNP&RNO

Training Outline


exercise


Associate-WCDMA RNP&RNO Training


Training Mode

Target Audience


to take the Huawei Certified Network

Professional-WCDMA RNP&RNO certification

exam.

Prerequisites



outlook.


communication.

Have qualifications for HCNA-Huawei WCDMA

RNP&RNO Technologies.

Objectives

Principle：

Familiar with the WCDMA communication theory.

Master the wireless network planning and optimization

process.


Master the UMTS coverage planning, capacity planning,

and neighbor / frequency planning, LAC planning,

scrambling code planning.

Grasp the relevant parameters of the network planning

and adjustment of principles.

Grasp the CW test method, the CW test data

processing.

Master the propagation model calibration processes,

methods.


Master the RF optimization of processes, methods, tools,

with network RF optimization capabilities.


in the wireless side of GSM Network.

To master the problems of the common words of

WCDMA system KPI analysis and network processing,

familiar, then the system KPIs (Access, retention and

mobility)optimization method.

Familiar with Huawei UMTS RNC maintenance

operations.

Able to independently finish the network optimization

reporting and problem analysis report writing.

Duration

11workdays

Maximum Class Size

16 persons

18 CDMA RNP&RNO

18.1 Huawei Certified Network Associate-Huawei CDMA RNP&RNO

Technologies Training Outline


exercise

Huawei Certified Network Professional-WCDMA

RNP&RNO Training


Training Mode

Target Audience


to take the HCNA CDMA RNP&RNO certification

exam.

Prerequisites



outlook.


communication.

Objectives

Principle：

Understandable of the CDMA basic theories /wireless

transmission /telecomunicatios as well as attenna and

associated parameters.


Familiar with radio transmission theoretics and

the usual transmission model.


Capable of independently writing the analysis of

electromagnetic interference, and providing preliminary

resolutions for the target area accordingly.

Capable of independently finishing site survey and

report upon request.

Capable of independently using related tools to survey

radio parameters and quality of antenna.

Capable of independently accomplishing DT/CQT

test(single site verification) by Pioneer, analyzing the

problems of DT/CQT by Navigator and deliver

resolutions accordingly

Capable of dealing with common customer’s complaint

by DT/CQT.

Familiar with the meaning and adjusting regulations of

commonly used Network Design parameters.

Duration

8 workdays

Maximum Class Size

16 persons

18.2 Huawei Certified Network Professional-Huawei CDMA RNP&RNO



exercise


Associate-Huawei CDMA RNP&RNO

TechnologiesTraining


Training Mode

Target Audience


to take the HCNP CDMA RNP&RNO certification

exam.

Prerequisites



outlook .


communication.

Have qualifications for HCNA-Huawei CDMA

RNP&RNO Technologies.

Objectives

Principle：

Familiar with CDMA communication theory.

Master wireless network planning and optimazition

process.


Master the elements which impact on coverage and

capacity. Familiar with the basic principle of power

configuration.

Master the Network structure of multi-trxs , familiar with

the theories of PN, LAC and Neighbour design.

Master the way of CW testing and related data

processing.

Master the corrective procedure of transmission model.

Master the related parameters and adjusting regulations

of Network Design.


Master the RF optimazition & procedure, methods and

tools, capable of processing GSM radio network RF

optimazition.


in the wireless side of CDMA Network.

Master CDMA common KPI analysis and network

problem solution, such as drop call, handover, voice

quality and data traffic .

Familiar with operating on HUA WEI CDMA BSC’s

flatform;

Capable of independently completing network

optimazition reports and generating problem analysis

reports.

Duration

8 workdays

Maximum Class Size

16 persons


exercise


CDMA RNP&RNO Technologies Training


19 Microwave RNP

19.1 Huawei Certified Network Associate-Huawei Microwave RNP


Training Mode

Target Audience


to take the Microwave planning certification exam

and those who hope to learn basic microwave

transmission principles and LOS survey process，

and basic TCP/IP knowledge.

Prerequisites



Objectives


will be able to：

Describe the wireless radio-technology theory and

understand electromagnetic wave propagate model in

free space.

Complete site LOS survey report independent.

Complete performance calculation for microwave links

independent.

Be familiar with popular parameters on microwave

planning, and performance adjustment methods

Be familiar with basic TCP/IP knowledge and Ethernet

principle.

Duration

3 Working days

Maximum Class Size

16 persons

TA08 3 d Lecture,Hands-on excercise

Huawei Certified Network Associate-Huawei

Microwave RNP Technologies Training


19.2 Huawei Certified Network Professional-Huawei Microwave RNP


Training Mode

Target Audience


to take the Microwave planning advanced

certification exam，and those who hope to learn

about frequency planning, interference analysis

and Ethernet traffic design.

Prerequisites



With hardware installation and commissioning

experience of Microwave or optical

Knowledge about Microwave telecom common

principle.

Objectives


will be able to：

With primary engineer requirements.

Be familiar with microwave telecom principle and TDM ,

Hybrid and IP radio working principle.

Complete primary planning for network topology and

capacity.

Be familiar with common frequency band and air

channel allocation regulation, could complete frequency

design and interference analysis for middle scale

network

Be familiar with microwave link design process and

optimize method.

Understand deeply common KPI of microwave design

and parameters selection regulations.

Complete general evaluation for microwave network

and afford related design suggestions.

Manage the microwave planning team.

Duration

3 Working days

Maximum Class Size

16 persons

TA08 3 d Lecture,Hands-on excercise


Microwave RNP Technologies Training


20 Site and Power System

20.1 Huawei Certified Network Associate- -Huawei Site and Power

System Technology and Device Training Outline

Training Mode

Target Audience


to take the Site and Power System certification

exam and those who hope to learn about basic

ITS1000M and Power3000 principles and Huawei

ITS1000M and Power3000 equipment.

Prerequisites

Having working experience in the operation and

maintenance of Power3000.

Be familiar with Battery group.

Objectives


will be able to:

Describe the structure, functions and features of

ITS1000M and Power3000 Solution.

Explain the functions and specifications of different

parts.

Outline the load capacity and ability of ITS1000M and

Power3000 Solution.

Execute the Field operation, such as Battery

replacement.

Perform ITS1000M and Power3000 Solution operation

and maintenance, etc.

Locate and eliminate faults, get experience from

troubleshooting practice.

Remote update software

Duration

9 workdays

Maximum Class Size

12 persons

ODC01 9 d Lecture, Hands-on exercise

Huawei Certified Network Associate- -Huawei Site and Power System Technology and Device Training


21 Hybrid Power Supply

21.1 Huawei Certified Network Associate- Huawei Hybrid Power Supply

Technology and Device Training Outline

Training Mode

Target Audience


to take the Hybrid Power Supply certification exam

and those who hope to learn about basic

Power1000 and Power2000 principles and Huawei

Power1000 and Power2000 equipment.

Prerequisites

Having working experience in the operation and

maintenance of D.G.

Be familiar with Battery group.

Objectives


will be able to:

Describe the structure, functions and features of

Power1000 and Power2000 Solution.

Explain the functions and specifications of different

parts.

Outline the load capacity and ability of Power1000 and

Power2000 Solution.

Execute the Field operation, such as Battery

replacement.

Perform Power1000 and Power2000 Solution operation

and maintenance, etc.

Locate and eliminate faults, get experience from

troubleshooting practice.

Remote update software

Duration

9 workdays

Maximum Class Size

12 persons

22 Hardware Installation Supervision (excluding RF products)

22.1 Huawei Certified Network Associate-Hardware Installation

Supervision (excluding RF products) Training Outline

Training Arrangement

Trainees

Personnel who attend the certification test of

hardware installation for Huawei telecom

equipment

Personnel who hope to know more about

hardware maintenance and troubleshooting of

Huawei equipment

Entrance Requirements

Huawei hardware installation personnel and Huawei

hardware installation sub-contractors

Dedicated personnel with basic electronic knowledge

and electrician skills

Objectives

Upon completion of this training program, the

trainees will understand the following subjects:

Introduction to EHS management during engineering

delivery

Telecom installation specifications

ODC00 9 d Lecture, Hands-on exercise

Huawei Certified Hybrid Power Supply — Huawei

Hybrid Power Supply Technology and Device

Training

Huawei certification of telecommunications

equipment hard mounted Coaching

Lectures,

drills

5 days


Specifications on common tools and wireless products

installation

Required knowledge about installability

User guide for common tools of communication project

MA5600 hardware installation guide

SOP of OptiX OSN 3500

Guide to core network UMG8900 cabinet cascaded

optical fiber installation (2008.05.20)

Core network hardware installation training material

Specifications on installing and laying out cables

Cable connector production

Duration

Five routine working days

Maximum number of trainees

20

23 Hardware Installation Supervision (including RF products)

23.1 Huawei Certified Network Associate-Hardware Installation

Supervision (including RF products) Training Outline

Training Arrangement

Trainees

Personnel who attend the certification test of

hardware installation for Huawei telecom

equipment

Personnel who hope to know more about

hardware maintenance and troubleshooting of

Huawei equipment

Entrance Requirements

Huawei hardware installation personnel and Huawei

hardware installation sub-contractors

Dedicated personnel with basic electronic knowledge

and electrician skills

Contents

Upon completion of this training program, the

trainees will understand the following subjects:

Introduction to EHS management during engineering

delivery

Huawei certification of telecommunications

equipment hard mounted Coaching

Lectures,

drills

6 days


Introduction to telecommunications room environment

Telecom installation specifications

Specifications on common tools and wireless products

installation

Required knowledge about installability

Introduction to common instruments and tools

BTS3900 hardware architecture and principle

DBS3900 hardware architecture and principle

Antenna and feeder system installation (Chinese video)

Quick installation guide to base station swap V1.0

Multimedia training material of tower installation

Specifications on installing and laying out cables

Training materials for making cable connectors

(outdoor)

Microwave product installation and commissioning

(training material for international projects)

Work instructions for the delivery of microwave co-base

stations (training material for international projects)

Duration

Six routine working days

Maximum number of trainees

20

Documents

Huawei Certification Training Catalog (Subcontractors) V1.2