HP-4 Indirect/Direct with Mitered Corners Installation ...€¦ · Slip Ring w/ Set Screw Part# 94015 Mounting Starter to Structure p. 4, Step 3 Joining Luminaires p. 5, Step 4 Joining

HP-4 Indirect/Direct with Mitered Corners Installation Instructions

1 of 10

© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form

- 98529. V5 EFFECTIVE DATE: 10/21/19Pr

otec

ted

by o

ne o

r mor

e US

Pat

ents

: 891

5613

; D70

2,39

1; D

702,

390;

D70

0,73

2

Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.comThis is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

Regressed Luminaires Use Same Instructions

Overview

• If luminaire contains a sensor or socket refer to the appropriate Addendum.

• All power connections should be installed according to local/national codes by a Certified Electrician.

• This installation requires proper support as each luminaire is being installed.

• DO NOT attempt to join luminaires together on the floor. Damage may result when lifted.

NOTES

HELPFUL VIDEOS

0-10V Dimming

Louver Removal

SimplePlug-Together

Wiring

Socket Removal & Installation

Universal &Robust Joints

EffortlessAccess

Step 1Mounting & SuspensionPage 2

Step 2Identification & PreparationPage 3

Step 3Mounting Starter to StructurePage 4

Step 5Opening LuminairesPage 6

Step 6Securing Luminaire JointsPage 7

Step 7Joining Mitered CornersPage 8

Step 8Securing Corner JointsPage 9

Step 9Closing LuminairesPage 10

Step 4Joining LuminairesPage 5


2 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19

Step 1 - Mounting & Suspension

Mounting Options

Suspension Locations

Option 1T-Bar Mounting - GridBox™ and Caddy Clips

• Install GridBox™ and electrical conduit at feed locations.• Install caddy clips at mounting point locations.• All caddy clips are to be secured to structure, per local building codes.

Option 2Drywall (C4) or other hard surfaces* - J-Box and Anchor Bolts

• Install J-Box and electrical conduit at feed locations.• Install anchor bolts at mounting point locations.• All anchor bolts are to be secured to structure, per local building codes.

* Other hard surfaces include: wood, sheet metal panels, steel beams, concrete or masonry. Use hardware appropriate for each surface material type.

X = Suspension Dimensions

Refer to Record Drawings and building plans to determine exactmounting, suspension points, and power feed locations.

GridBox™ (provided)

1/4" -20 Anchor Bolt (by others)

Caddy Clip (provided)

J-Box (by others)

X1 X2

X3

Starter JoinerID: 1 ID: 2

Endcap

GridBox™(provided)

1/4"-20 Anchor Bolt(by others)

J-Box(by others)

Caddy Clip(provided)

Mounting Option 1 Mounting Option 2

EnderID: 3

or or or

or


3 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19

ABC Corporation - A12345

HP-4- ID - 32' - S - 835 - 120V - SC

HP-4 ID - X'ID: 1

STARTER

Factory Order NumberJob Name

Unique LuminaireID Number

Full Catalog Order ID

Luminaire Section Type

Luminaire Type and/or Run Length

Louver Removal

Backplate

Uplight Diffuser

Protective Bag

C. Remove Uplight Diffuser

ID Labels

• Carefully remove all uplight diffusers, keeping them inside their protective bag.

• Set aside all uplight diffusers to prevent from getting dirty or damaged.

• Ensure uplight diffusers can be identified back to their corresponding luminaire.

Remove Diffusers

Remove Louvers

B. Remove Downlight Diffusers or Louvers

• Carefully remove all downlight diffusers or louvers, keeping them inside their protective bags.• FOR LOUVERS: Release louvers by inserting the blade of a putty knife approximately

1" down behind louver edges and pry up.• Set aside all downlight diffusers or louvers to prevent from getting dirty or damaged.• Ensure downlight diffusers or louvers can be identified back to their corresponding luminaire.

ID Labels

ID Labels

Downlight Diffuser

Louver

Putty Knife

Protective Bag

Protective Bag

NOTE: For White Cross Blade Baffle, refer to Baffle Tether Addendum before installing.

A. Identify Luminaires

• Identify all luminaires by their ID label that can be found on the box, the diffuser, and inside the luminaire.

• NOTE: Exact location of labels in these areas may vary.• Remove all luminaires from their box.• Refer to Record Drawings that can be found in the hardware kit.

Step 2 - Identification & Preparation

Caddy ClipC1 Ceiling - Part# 94001C2 Ceiling - Part# 94020C3 Ceiling - Part# 94029Mounting & Suspensionp. 2, Step 1

2" Drywall Support CanopyPart# 94017Mounting Starter to Structurep. 4, Step 3Joining Luminairesp. 5, Step 4Joining Mitered Cornersp. 8, Step 7

5" Canopy

5" Dual Feed Canopy

Part# 94085GridBox™

Dual GridBox™

Part# 89159

Part# 89199 Mounting & Suspension p. 2, Step 1

3-1/2" Canopy

3-1/2" Dual Feed Canopy

Part# 89191

Part# 89192Mounting Starter to Structurep. 4, Step 3Joining Luminairesp. 5, Step 4Joining Mitered Cornersp. 8, Step 7

Part# 94145Mounting Starter to Structurep. 4, Step 3Joining Luminairesp. 5, Step 4Joining Mitered Cornersp. 8, Step 7

2" T-Bar Support CanopyPart# 89193Mounting Starter to Structurep. 4, Step 3Joining Luminairesp. 5, Step 4Joining Mitered Cornersp. 8, Step 7

Mounting Option 2Mounting Option 1

Cable Bushing

Aircraft Cable

Part# 94014

50" - Part# 94515-12 (Std.)100" - Part# 94515-14150" - Part# 94515-18Mounting Starter to Structurep. 4, Step 3Joining Luminairesp. 5, Step 4Joining Mitered Cornersp. 8, Step 7

Slip Ring w/ Set ScrewPart# 94015Mounting Starter to Structurep. 4, Step 3Joining Luminairesp. 5, Step 4Joining Mitered Cornersp. 8, Step 7

Yoke Bracket

#10-32 x 5/8" Screw

Part# 45042

Part# 94144Securing Luminaire Jointsp. 7, Step 6Securing Corner Jointsp. 9, Step 8

GripperPart# 68129Mounting Starter to Structurep. 4, Step 3Joining Luminairesp. 5, Step 4Joining Mitered Cornersp. 8, Step 7

Safety CrimpPart# 94514Closing Luminairesp. 10, Step 9

• Finelite has provided items listed here, with their Finelite part numbers. These items can be found in separate boxes shipped with the luminaire.

• Account for all parts and set aside until they are needed.

• All other hardware needed for this installation will be by others.

Kitted Hardware

CAUTION

Arrange luminaires in order according to ID# at their install locations.

#8-18 x 1/4" ScrewsPart# 69026Closing Luminairesp. 10, Step 9


4 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19

Option 1GridBox™

Option 2J-Box

3-1/2" Canopy(provided)

5" Canopy(provided)

2" Drywall Support Canopy(provided)

Slip Ring w/ Set Screw(provided)

2" T-Bar Support Canopy(provided)

Mounting Option 1 (shown) Mounting Option 2

Bushing/Cable Assembly(provided)

Option 1GridBox™

Option 2J-Box Slip Ring


5" Canopy(provided)

0-10V Dimming

A. Mount Starter to Structure

Step 3 - Mounting Starter to Structure

WIRING LEGEND

Black Hot Line Voltage

White Neutral Line Voltage

Green Ground

Grey Dimming 0-10V DC

Purple Dimming 0-10V DC

• Slide canopy appropriate for electrical type options onto mounting bolt (anchor bolt or caddy clip bolt).• (Option 2 only) Thread the slip ring onto anchor bolts and secure with set screw at both mounting locations.• Thread the bushing/cable assembly onto mounting bolts.• While properly supporting luminaire, maneuver luminaire to ceiling.• Locate grippers at luminaire ends and feed end of aircraft cable through it by depressing top of gripper.• Level luminaires to desired height by depressing top of grippers to adjust cable lengths.

• (Option 1) Feed power cord through the 3-1/2" canopy and connect wires inside the GridBox™.

• (Option 2) Feed power cord through the 5" canopy and connect wires inside the J-Box.• CRITICAL: If installing mitered corner, PROCEED TO STEP 7.

Feed Canopy


Support Canopy(provided)

Mounting Bolt(see options, p.2)

Gripper(attached)

B. Make Electrical Connections

LevelLuminaires


5 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19


5" Canopy(provided)






Starter

Joiner

Joiner

Starter

Aligner Sleeve

Step 4 - Joining Luminaires

Gripper(attached)

A. Mount Joiner to Structure

CAUTION

DO NOT attempt to join luminaires together on the floor. Damage may result when lifted. Follow these instructions. CAUTION

Once luminaires are aligned together, joiner luminaire is not yet secure. Ensure it does not slide off as it rests on the starter luminaire.




B. Join Luminaires

• Align joiner with aligner sleeves on starter and slide together. Be careful not to damage any wiring.• If necessary, lift both luminaires, then slide together.

• For the joiner luminaire, slide canopy appropriate for electrical type onto mounting bolt (anchor bolt or caddy clip bolt).

• Thread the bushing/cable assembly onto mounting bolt.• While properly supporting luminaire, maneuver luminaire to ceiling.• Locate gripper at luminaire ends and feed aircraft cable through it by depressing top of gripper.• Level luminaires to desired height by depressing top of grippers to adjust cable lengths.

LevelLuminaires


6 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19

EffortlessAccess

Step 5 - Opening Luminaires

Downlight Backplate

Putty Knife Option

Backplate

Backplate

FlatheadScrewdriver

Clip

Backplate

• Carefully rotate downlight backplates out at the joints only and let them hang from luminaire body.

Flathead Screwdriver Option

Release Downlight Backplates

Joiner

Starter

• Release the backplates from clips by sliding the blade of a putty knife behind backplate edges.• To use a flathead screwdriver, press end of screwdriver (from inside the luminaire) against the clip, until the backplate is released.

Clip

Backplate

Putty Knife


7 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19

SimplePlug-Together

Wiring


Universal &Robust Joints

Step 6 - Securing Luminaire Joints

B. Make Electrical Connections

• Connect plug-together wiring.

Yoke Bracket w/ Screw#10-32 x 5/8" (provided)

Joiner

Starter

Plug-Together Wiring

A. Secure Joint with Yoke Brackets

Joiner

Starter

Cross Section View

• FOR SENSOR OR SOCKET: If luminaire contains a sensor or socket at joint, refer to page 4 of appropriate Addendum before Securing Luminaire Joints.

• Before installing yoke brackets, ensure the joining ends of luminaires meet flush and square.• CRITICAL: Ensure yoke brackets properly engage with aligner sleeves.• Secure joint by threading (but not yet tightening) yoke screws through yoke brackets and

into the aligner sleeves.NOTE: Yoke screws should be installed directly across from each other, not diagonally, and in holes furthest from the joint line. One yoke screw per one yoke bracket.

Yoke Screw(provided)

Aligner Sleeve

Yoke Bracket(provided)

YESNO

Joiner Aligner Sleeve

Luminaire Joint

IN ALIGNMENT CORRECTLY INSTALLED

Luminaire Joint Luminaire Joint

YOKE SCREW ALIGNMENT Bottom-Up View

Joiner Aligner Sleeve


8 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19


Step 7 - Joining Mitered Corners

C. Open Downlight Backplates A. Mount Ender to Structure

Aligner Sleeve

Downlight Backplate

Joiner

Backplate

• For the ender luminaire, slide canopy onto mounting bolt (anchor bolt or caddy clip bolt).• Thread the bushing/cable assembly onto mounting bolt.• While properly supporting luminaire, maneuver luminaire to ceiling.• Locate gripper at luminaire ends and feed aircraft cable through it by depressing top

of gripper.



• Carefully rotate downlight backplates out at the joints only and let them hang from luminaire bodies.


Ender

Joiner

Ender

Joiner

Starter


5" Canopy(provided)





• Align ender luminaire with aligner sleeves on joiner and slide together. Be careful not to damage any wiring.

• If necessary, lift both luminaires, then slide together.

B. Join Mitered Corners

Ender


9 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19

IN ALIGNMENT

CORRECTLY INSTALLED

Mitered Corner Joint

Mitered Corner Joint

¹ Screwdriver with 6" bit required.

Step 8 - Securing Corner Joints

Yoke Bracket w/ Screw#10-32 x 5/8" (provided)

A. Secure Joint with Yoke Brackets B. Make Electrical Connections

• Connect plug-together wiring.

Plug-Together Wiring

Ender

Joiner

• Before installing yoke brackets, ensure the joining ends of luminaires meet flush and square.• CRITICAL: Ensure yoke brackets properly engage with aligner sleeves.• Secure joint by threading (but not yet tightening) yoke screws through yoke brackets and

into the aligner sleeves.• Level all luminaires to desired height by depressing top of grippers to adjust cable lengths.• Tighten yoke screws¹ until joint seam of luminaires is closed.

Aligner Sleeve

Ender

Yoke Screw(provided)

Yoke Bracket(provided)

Joiner

LevelLuminaires


10 of 10


- 98529. V5 EFFECTIVE DATE: 10/21/19

Safety Crimp(provided)

Safety Crimp(provided)

End Plate

NOTE: For White Cross Blade Baffle, refer to Baffle Tether Addendum before installing.

B. Crimp Cables

Plate Screw

Aircraft Cable

Step 9 - Closing Luminaires

ID: 1

ID: 1

ID: 1

ID: 2

ID: 2

ID: 2

ID: 3

ID: 3

ID: 3

• NOTE: If your installation includes a battery backup, please see addendum (98333) that should be included with your kitting package.• FOR SENSOR OR SOCKET: If luminaire contains a sensor or socket at joint, refer to page 5 of appropriate Addendum before Closing Luminaires.• Reinstall any open backplates by rotating into luminaire body and snapping back into clips.• Remove diffusers or louvers from protective plastic bags.• CAUTION: Wear gloves to keep diffuser or louver surface clean.• CRITICAL: Be sure to install correct diffuser or louver to its corresponding luminaire ID.• NOTE: For White Cross Blade Baffle, refer to Baffle Tether Addendum before installing.• Install diffuser or louver into luminaire body, ensuring it snaps into place.• Turn power on to luminaires.

• Ensure all leveling has been performed prior to applying safety crimp.• Loosen (but do not remove) plate screw and slide end plate open.• Loop aircraft cable through safety crimp.• Crimp, cut excess cable, and tuck back into luminaire body. • Close end plate and tighten plate screw to secure. Typical for each

aircraft cable.

A. Release Uplight Backplate

• Remove #8-18 x 1/4" screws to release uplight backplate.• Lift backplate out of housing channel, pulling wiring harnesses

through the housing. DO NOT disconnect LED board harnesses.• Let backplate rest atop luminaire.

Uplight Backplate

Uplight Backplate

#8-18 x 1/4" Screw (provided)

#8-18 x 1/4" Screws(provided)

C. Final Step - Replace Backplates & Diffusers or Louvers


Documents

HP-4 Indirect/Direct with Mitered Corners Installation ...€¦ · Slip Ring w/ Set Screw Part# 94015 Mounting Starter to Structure p. 4, Step 3 Joining Luminaires p. 5, Step 4 Joining