Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.
WARNINGPressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced options in the Print menu.
Install your Maestro RR according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE1
2
3
SELECT VEHICLE PRINT PAGES NEEDED
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEChRySLER 300
BASE 2005-2007retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler 300 Base 2005-2007
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler 300 Base 2005-2007
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler 300 Base 2005-2007
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler 300 Base 2005-2007
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/LtBlue (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 White/DkBlue (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler 300 Base 2005-2007
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEChRySLER PT CRUISER
BASE 2006-2010retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler Pt crUiser Base 2006-2010
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler Pt crUiser Base 2006-2010
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler Pt crUiser Base 2006-2010
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler Pt crUiser Base 2006-2010
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/LtBlue (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 White/DkBlue (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
chrysler Pt crUiser Base 2006-2010
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEDODGE CALIBERBASE 2007-2008
retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge caliBer Base 2007-2008
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge caliBer Base 2007-2008
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge caliBer Base 2007-2008
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge caliBer Base 2007-2008
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/Tan (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 White/DkBlue (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge caliBer Base 2007-2008
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEDODGE ChARGERBASE 2006-2007
retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge charger Base 2006-2007
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge charger Base 2006-2007
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge charger Base 2006-2007
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge charger Base 2006-2007
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/LtBlue (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 White/DkBlue (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge charger Base 2006-2007
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEDODGE DAkOTABASE 2005-2007
retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dakota Base 2005-2007
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dakota Base 2005-2007
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dakota Base 2005-2007
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dakota Base 2005-2007
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/LtBlue (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 Pink/Red (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dakota Base 2005-2007
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEDODGE DURANGOBASE 2004-2007
retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dUrango Base 2004-2007
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dUrango Base 2004-2007
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dUrango Base 2004-2007
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dUrango Base 2004-2007
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/Pink (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 Pink/Red (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge dUrango Base 2004-2007
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEDODGE MAGNUMBASE 2005-2007
retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge magnUm Base 2005-2007
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge magnUm Base 2005-2007
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge magnUm Base 2005-2007
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge magnUm Base 2005-2007
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/LtBlue (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 White/DkBlue (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge magnUm Base 2005-2007
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEDODGE RAM
BASE 2006-2008retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge ram Base 2006-2008
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge ram Base 2006-2008
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge ram Base 2006-2008
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge ram Base 2006-2008
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/LtBlue (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 White/Brown (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
dodge ram Base 2006-2008
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEJEEP GRAND ChEROkEE
BASE 2005-2007retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP grand cherokee Base 2005-2007
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP grand cherokee Base 2005-2007
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP grand cherokee Base 2005-2007
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP grand cherokee Base 2005-2007
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/LtBlue (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 White/DkBlue (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP grand cherokee Base 2005-2007
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIESNone
PROGRAMMED FIRMWAREADS-RR(SR)-CHR01-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro CH2 Installation Harness
INSTALL GUIDEJEEP PATRIOT
BASE 2007-2008retains steering wheel controls, Uconnect, Uconnect BlUetooth, and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP Patriot Base 2007-2008
Automotive Data Solutions Inc. © 2015 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
Radio Wire Reference Chart 6
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP Patriot Base 2007-2008
Automotive Data Solutions Inc. © 2015 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifi er.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a factory amplifi er.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a factory amplifi er.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the CH2 T-harness and match the wire functions.
STEP 2• Connect the factory harness to the CH2 T-harness.
STEP 3• Access the OBDII connector located under the driver side
dashboard.
• Connect the BROWN /RED wire of the CH2 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
• Connect the BROWN /YELLOW wire of the CH2 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors)
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
4 5 6 7 1121 3
15 16 17 18
8 9 10
19 20 21 221312 14
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP Patriot Base 2007-2008
Automotive Data Solutions Inc. © 2015 4
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
C
A
H
FG
D
C
A
G
F
H
1
D
BROWN/RED - CANHBROWN/YELLOW - CANL
NOTE: PIN SIDE VIEW.CONNECT TO TWISTED WIRES BEHIND CONNECTOR.
WIRING DIAGRAM
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
MAINHARNESS
DATACABLE
AUDIOCABLE
CONNECT TOAFTERMARKET RADIO
CH2 T-HARNESS
FACTORY RADIOHARNESS
OBDII CONNECTOR
WIRES FROMVEHICLE
STEP 1WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
BROWN (NOT CONNECTED)
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
SEE CHARTON NEXT PAGEFORRADIO WIRECOLORS
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
WHITE (NC)WHITE/BLACK (NC)GRAY (NC)GRAY/BLACK (NC)
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED
CONNECTIONSWITHOUT AMP
OR
OR
CONNECTIONSWITH AMP
WIT
HO
UT
AM
PW
ITH
AM
P
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP Patriot Base 2007-2008
Automotive Data Solutions Inc. © 2015 5
VEHICLE WIRE REFERENCE CHART
WireDescription
Connector Name
ConnectorColor
ConnectorType Position Wire Color Polarity Wire
Location
CanH A ~ 16 pin 06 White/Tan (DATA) OBDII connector, under driver side dash
CanL A ~ 16 pin 14 White/DkBlue (DATA) OBDII connector, under driver side dash
ADS-RR(SR)-CHR01-DS maestro.idatalink.com
JeeP Patriot Base 2007-2008
Automotive Data Solutions Inc. © 2015 6
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink