How to Site an Earth Station Antenna

8/11/2019 How to Site an Earth Station Antenna

1/5

How to site an earth station antenna

When selecting the location for an earth station antennaof any size, the primary

consideration is to ensure a clear view of the orbital arc, which allows the antenna to "see"

the maximum number of satellites. Placing an antenna on a rooftop is often the optimal

solution. However, extremely high winds can damage or destroy a parabolic dish antenna.

Most properly installed earth station antennas are designed to survive winds of at least 60

or 70 miles per hour. When located in areas prone to hurricanes, tornadoes, or seasonal

periods of high winds that can exceed these speeds, special considerations should be made

in selecting the location of the antenna.

Properly siting the antenna can increase the chances of surviving high wind conditions.

Locating an antenna on the leeward side of buildings or hillsides, or using large roof

structures, such as air conditioning units as windbreaks, while maintaining a clear view of

the orbital arc, can make the difference between an antenna's survival or destruction in astorm. As every rooftop antenna installation is unique, it is important to work with the

building owner or landlord in order to determine the optimum location.

Many manufacturers make antennas and antenna mounts capable of surviving higher wind

conditions, than standard units. High wind antennas are more robust, and reinforced

mounts should be considered in areas having an elevated risk of wind damage to outdoor

structures.

In the case of non-penetrating roof mounted antennas being installed in high wind areas,

the maximum amount of ballast recommended by the manufacturer must be installed, or

even exceeded, in order to ensure that the antenna does not move from its moorings duringhigh wind conditions. The ability of the roof to bear this additional load must be considered

to avoid damaging the building upon which the antenna is mounted. In general, hard

mounting an antenna to a building is preferred over the use of a non-penetrating roof

mount.

Having a replacement antenna available in the event of an emergency is a costly, yet highly

effective means of mitigating the risk of prolonged outages in crucial networks. Installing a

second, fully equipped and operational antenna on a nearby building provides full

redundancy, and "pace diversity" for the system. While costly, this risk mitigating option

may be appropriate in high priority, high value communications networks.

Earth station antennasproviding high value, critical communications links must be

protected against natural, and man-made threats. While some devastating situations are

unavoidable, it is incumbent upon systems engineers to design a level of security and

survivability into earth station facilities, which is commensurate with the importance of the

communications traffic being carried by the facility. Selecting an appropriate location for the

antenna can greatly increase its chances for surviving a storm or avoiding deliberate attack.


2/5

Providing sufficient spares, and or redundancy/diversity can avoid outages or greatly reduce

down time in the event of an interruption caused by either weather or attack.

The Maintenances of Earth Station Antenna -

1

The Maintenances of Earth Station Antenna

We summarize many years experience of production and maintenance of Earth Station Antenna andcombined with the feedback of many customers from all over the world to creat the daily inspectionmanual. It contain "Surface Maitenance","Antenna Fasteners","Ground","Cable and connector","Shutdown Maintenance","Maintenance Record".

The simple maintenance for earth station antenna can reduce the antenna failure probability and

extend the antenna life, so a regular and complete antenna maintenance planning will be helpful forthe antenna normal operation.

Appropriate maintenance planning is a kind of commercial insurance. Check the completion of thewhole structure and ensure the normal operational capability by the simple and low-cost surface

maintenance; Check the electrical performance, and comply with the maintenance regulation in themanufacture's operational maintenance manual so as to reduce the occurrence of antenna failure.

1. Surface Maintenance

Check the complete paint surface and electroplating surface, as well as fixed structure. First rub therust spot on the electroplating surface by metal wire brush or abrasive paper, and then coat a layer ofzinc-rich coating or a layer of rust inhibitor which won't require the complete clearance of the rust.

The user should repair it even if only a little of the finish peeling, spalling or color fading, or it will

become more and more serious. And the user must accord with the antenna manufacturer's regulationfor the paint surface and coating specification, because the wrong coating method will affect thesignals accept. For example, the dark-colored antenna reflector surfaces can absorb easily, and so itcan give rise to high temperature, which can cause the signal distortion. Too much lead paint canmake the signals loss by attenuation or scattering.

2. Antenna Fasteners

The nuts, bolts, rivets and other fasteners in the installation will be affected by atmospheric effect orinternal corrosion. Regardless of any corrosive components and the error installation will be found inthe routine maintenance. At this time the users should tighten the loosen nuts and replace the lost,

rust and corrosive components.

With the ASTM (American Society for Testing and Materials Institute) A325 or other occasions offriction components, the user must replace the loosen or corrosive components, because in theprocess of re-tightening it will make the fasteners get the reuse term. Also the corrosive A325 metalparts should be replaced not be tightened.

Often there're pins inserting in the pivots of the adjustable antenna bracket. Check if the activities of

these jointing are flexible, and lubricate the oil by a grease-gun with oil jet. If the antenna rotates notflexibly, the user should replace the pin.


3/5

Check the metal fasteners on the antenna reflector and back structure. Except ASTM A325 must bereplace, the user can tighten the loosen parts. The lost, rust and corrosive fasteners should bereplaced. These check processes are also suitable for the operational platform when assembling theantenna, as well as assisting the reflector and reflector support.

3. Ground

No matter how high the buildings, the antenna and bracket should be grounded to prevent thelightning strikes. Inspect if the mechanical of grounding system and non-mechanical connection areconnected.

Analyze if the grounding connection is connected by the earth loop impedance instrument. Accordingto the test results the user can decide the cost of the excavating work. Check if the mechanicalgrounding parts are rust, corrosive or loosen. Replace the rust and corrosive fasteners so as to limitthe inductance value.

Unload the grounding sharp dogleg head on the antenna or bracket. Contrast to the Biddle

megohmmeter, test the target value which is made after site grounding resistance to check thegrounding system. According to the test results determine whether adopt auxiliary groundingmeasures.

On the place which can use the step auto-tracking device, check whether the pedal is level by alongitude and latitude stadia. If the pedal is not level, it can affect the antenna position calculation.Adjust the level nut under the base plate to make the antenna keep level.

If the anchor bolts prevent to adjust the pedal level, adjust it while fixing the antenna. After adjusting,check if the cement sealing of the antenna foundation and anchor bolts spall, crush and shift. If it isdamaged, even a little, also should be repaired. After adjusting, the controller should be programmedagain.

If some devices are mounted in the antenna box which is on the back of the reflector, check if there'saccumulated water or a large number of termite or rodent infested in the box. Repair or seal the

crack, even if it is little. If the user don't care about it, ants, mice and other animals will causeincredible losses.

The Maintenances of Earth Station Antenna -

2

--

The Maintenances of Earth Station Antenna- 14. Cable and connector

Intermediate facility link cable transmits the signal between the antenna and computer room. Check ifthese cables are damaged. If there's something wrong with VSWR or insertion loss, the user shouldtest and check whether the cables need to be replaced or be repaired.


4/5

When repairing the cables, the user can splice them in the new position, but it can cause some signalsattenuation. With s Time Domain Reflector (TDR) check the position of the broken line. With a voltagemeter check all the cables and connectors of the electrical properties and connectivity.

The coaxial cable with a bend head in excess of the minimum bend radius should be tested. Aftertesting if it doesn't comply with the cable specification, it should be replaced.

Ensure the IFL cable and other cable support and routing (positioning and bending radius) accord withthe manufacturer's technical requirements. Replace the lost, rust and corrosive backup supports.When supporting IFL cables, it is better to use stainless steel cable link or cable clamp than the plasticrope. Stainless steel link should be used to fix the elliptical waveguide. Inspect the cablemanufacturer's recommendations.

If the stainless steel link or clip is not useful, and the cable manufacturer haven't specified anystainless steel link or clip, in this case the user can only use black nylon rope, the white or bright-colored rope is easy to be fragile in the sun. The user should always check the cable rope, because thenylon rope is easy to be loosen than stainless steel clip.

Check the IFL connectors and connection parts. Replace the connectors which appear fracture line,line antihypertensive or other problems. If IFL cables come from the catheter, the user should check

the catheter and other connectors. Check if the catheter input is strict, if there's accumulated water inthe catheter, the water will freeze, which will squeeze the cable broken.

Check the feed combiner flexible elliptic waveguide line, if it is damaged, replaces it. If the systeminflation pressure is not enough, corrosion can change the signal-to-noise ratio to affect the signal orcause the antenna stop working.

5. Shutdown Maintenance

Some maintenance work should be done when the antenna don't stop working, but most of themaintenance work need to be done after the antenna stop working. For example, when moving theantenna or cut down IFL line, the user must shutdown the antenna. First check the antenna azimuthand elevation bracket. Look if there's some fracture and hardening phenomenon for the protection

cover of the support bracket, if need, replace it.

For the motorized antenna or the antenna which points to a Satellite for a long time, sometimes those

antennas also need to be moved. This step can be considered as part work of daily check in each year,except Antesky Science Technology Inc Have another regulation. When doing the maintenance,according to the maintenance period table of Antesky Science Technology Inc (Antenna Manufacturer:clear the support screw, and lubricate the oil.

If the user finds the support bar moved on one position and was wear, it should be adjusted. Whenrotating the antenna, ensure that mechanical limit switch can stop after antenna motor finishes theplaned journey. The limit switch malfunction can make the antenna rotate continuously until it will bedamaged or hit with other objects.

Check the operational maintenance of Antesky Science Technology Inc note that the specialrequirements and suggest when to lubricate the oil or when to inject the oil for the azimuth, elevation,polarization and other motors. Antenna motor wire box should be dust-free and moisture-proof and allthe connection should be fixed. If due to improper maintenance of the equipment, Antesky will not beresponsible for warranty.

6. Maintenance Record


5/5

Keep a maintenance record. At the beginning of installing the antenna, leave a record with date andphotos. Then maintain once, keep a record once, so as to keep a complete antenna system record.

In the antenna valid life keep a record of antenna pattern so as to find the phenomenon of the systemsignal dropping.

If it is required to shut down the antenna and do the maintenance, you'd better arrange themaintenance work when the antenna doesn't work or within one hour at off-peak period. If theantenna can't stop work, transfer this antenna's work to another temporary earth station antenna.

9m Earth Station Antennas introduction

9m Earth Station Antennas are used for broadcast applications and high-density data, voice, andcommunications networks

Antesky Corporation introduced a 9.0 meter dual-reflector Earth Station Antenna. The new antennahas a computer-optimized dual-reflector Prime-focus optics system for high gain and excellent

radiation pattern performance. It is manufactured using close-tolerance techniques established forantennas operating at high frequencies. These ensure an extremely accurate surface contour,resulting in high antenna performance efficiency. The new ante-sky antennas are available for C orKu-Band 2 or 4-port configurations with linear or circular polarization. All 9.0-meter antennas complywith AsiaSat, APSTAR, Eutelsat, Intelsat(R), ITU-R and US FCC standards.

Earth station antennas offer maximum durability with minimal maintenance. Their rugged aluminumand steel construction ensures extended product life. The ground mount assembly is made from hot-dipped galvanized steel for long life. There is a 3-year warranty on all structural components.

The 9.0-meter ESA offers standard wind survival up to 125 mph (200 km/h) in any position ofoperation. Other options available include anti-icing equipment, waveguide cross axis kits, andpressurization systems. Microprocessor-based step track control and motorizable mount options arealso available.

Antesky Science Technology Inc. is a global supplier of communications systems equipment andservices. Major markets are earth station antennas C which includes Satellite communicationantennas, TVRO antennas, SNG antennas and flyaway antennas.

Documents

How to Site an Earth Station Antenna