How to Reset the Maintenance Counter Message.doc

7/27/2019 How to Reset the Maintenance Counter Message.doc

1/2

How to Reset the Maintenance Counter Message

LaserJet 4000/4050/4100LaserJet 5000/5100

Reset at: (200,000 pages)

1. Shut printer off. (Use the SHUT OFF switch)

2. Hold down the Left Side of the ITEM and VALUE

Buttons while powering the Printer back on.

3. Continue to hold the Buttons until the Printersays RESET MAINTENANCE COUNTER thenrelease the Buttons.

Click Here For Printer Friendly Version


1. Shut the Printer off. (Use the shut off switch)

2. Hold down the Left Side of the ITEM and VALUE

Buttons while powering the Printer back on.

3. Continue to hold Buttons until the Printer saysRESET MAINTENANCE COUNTER, Then releasethe Buttons.


LaserJet 9000/9050LaserJet 5si


1. Power off the Printer.

2. Press and hold the CHECK ? Button locatedon the center of the display.

3. Now power the Printer on while pressing the

CHECK (?) Button.

4. Now hold the CHECK (?) for at least 3-4seconds, then release the Button.

5. Now you will see a Select Language prompt onyour Printers Display.

6. Now press the QUESTION MARK (?)Button.

7. Now the MAINTENANCE KIT will be displayed.

8. Now press the CHECK (?)Button and you arefinished.



1. Turn the Printer Offline.

2. Press the MENU Button until Configuration Menuis displayed.

3. At this time press the ITEM Button one (1)time.

4. (Service Message = Off ) will be displayed.

5. Now press the SELECT Button.

6. Now press the ONLINE Button.

7. Now you are finished.


LaserJet 8000/8100/8150LaserJet 4200/4300
http://www.feedroller.com/prntrfrnd4000_4050_4100.htmlhttp://www.feedroller.com/prntrfrnd5000_5100.htmlhttp://www.feedroller.com/prntrfrnd9000_9050.htmlhttp://www.feedroller.com/prntrfrnd5si.htmlhttp://www.feedroller.com/prntrfrnd4000_4050_4100.htmlhttp://www.feedroller.com/prntrfrnd5000_5100.htmlhttp://www.feedroller.com/prntrfrnd5000_5100.htmlhttp://www.feedroller.com/prntrfrnd9000_9050.htmlhttp://www.feedroller.com/prntrfrnd5si.html

7/27/2019 How to Reset the Maintenance Counter Message.doc

2/2


1. To access the Service Mode, power the Printerdown/off and hold down the SELECT & JOBCANCEL Buttons.

2. Power the Printer back on while holding these

two (2) Buttons.

3. Hold these Buttons for at least 4 seconds thenrelease.

4. Now press the MENU & SELECT Buttons.

5. You should see SERVICE MODE in thedisplay.

6. The Printer will cycle, This is normal.

7. Now press the MENU Button, Then the SERVICEMENU will be displayed on your printer.

8. Now press the ITEM Button until

MAINTCOUNT is on the display.

9. Now use the + or Buttons to change thenumbers to 0s.

10. Now press the SELECT Button.

11. Now an Asterisk (*) will appear and you are

finished.

12. To exit the Service Mode press the GO Button.



1. Use the following Pin Codes:For LaserJet 4200 (11420002)

For LaserJet 4300 (11430002)

2. Press the SELECT Button to open the Menus.

3. Now use the UP Arrow or DOWN Arrow Buttonsto scroll to SERVICE.

4. Once at SERVICE, Press the SELECT Button.

5. Now press the UP or DOWN Arrow Buttons until

the first digit of the Pin Code appears.

6. Now press the SELECT Button to save that digit.

7. Repeat this selection procedure until the entireeight (8) digit Pin Code is saved.

8. The Service Sub Menu will appear on the displayof the Printer.

9. Now use the UP and DOWN Arrows to scroll tothe Maintenance Item on the Service Sub Menu and

press the SELECT Button.

10. Now you can set the number of pages since thelast Maintenance Kit was installed.

11. The printer automatically exits the ServiceMenu after about one (1) minute if no Buttons arepressed. You can also hit the PAUSE/RESUMEButton to exit.

http://www.feedroller.com/prntrfrnd8000_8100_8150.htmlhttp://www.feedroller.com/prntrfrnd4200_4300.htmlhttp://www.feedroller.com/prntrfrnd8000_8100_8150.htmlhttp://www.feedroller.com/prntrfrnd4200_4300.htmlhttp://www.feedroller.com/prntrfrnd4200_4300.html

Documents

How to Reset the Maintenance Counter Message.doc