6
How to: Power Board Replacement Sette 30, Sette 270, Sette 270W, Sette 270Wi Time: 20 min Difficulty: Medium Tools/supplies: Torx 10 driver. Needle Nose Pliers. #0 Phillips driver. Parts: Sette Powerboard (SKU: 110v - S060 / 220v - S061) Additional Resources: Case Removal Guide *** Unplug the grinder from power supply *** www.baratza.com [email protected] rev. 6/6/2019 ver. 1.1 Remove the case using the Case Removal Guide Sette PCB - S060 (110v) S061 (220v) Pliers Phillips Torx 10

How to: Power Board Replacement - Baratza...*** Unplug the grinder from power supply *** [email protected] rev. 6/6/2019 ver. 1.1 Remove the case using the Case Removal Guide Sette

  • Upload
    others

  • View
    3

  • Download
    0

Embed Size (px)

Citation preview

Page 1: How to: Power Board Replacement - Baratza...*** Unplug the grinder from power supply *** support@baratza.com rev. 6/6/2019 ver. 1.1 Remove the case using the Case Removal Guide Sette

How to: Power Board ReplacementSette 30, Sette 270, Sette 270W, Sette 270WiTime: 20 minDifficulty: MediumTools/supplies: Torx 10 driver. Needle Nose Pliers. #0 Phillips driver.Parts: Sette Powerboard (SKU: 110v - S060 / 220v - S061)Additional Resources: Case Removal Guide

*** Unplug the grinder from power supply ***

www.baratza.com [email protected] rev. 6/6/2019

ver. 1.1

Remove the case using the Case Removal Guide

Sette PCB - S060 (110v) S061 (220v)

Pliers

Phillips Torx 10

Page 2: How to: Power Board Replacement - Baratza...*** Unplug the grinder from power supply *** support@baratza.com rev. 6/6/2019 ver. 1.1 Remove the case using the Case Removal Guide Sette

www.baratza.com [email protected] rev. 6/6/2019

Pg. 2

Possible High Voltage

CAUTION: The capacitor is normally discharged however it may retain a charge. Do not touch the exposed metal at the rear of the component.

ADVISORY

ADVISORY

Unplug display, power cord and motor from circuit board

Use needle nose pliers to unplug the interlock switch connector.

Bend this component for easier access

Page 3: How to: Power Board Replacement - Baratza...*** Unplug the grinder from power supply *** support@baratza.com rev. 6/6/2019 ver. 1.1 Remove the case using the Case Removal Guide Sette

www.baratza.com [email protected] rev. 6/6/2019

Pg. 3

Remove the 2 screws to release the power board.

*There may be two additional screws securing the board. If this is the case, refer to page 4 of this guide*

Install the new power board and secure the screws.

Plug in the display, power cord, motor and interlock switch connectors.

Reinstall the case and return the unit to operation.

Page 4: How to: Power Board Replacement - Baratza...*** Unplug the grinder from power supply *** support@baratza.com rev. 6/6/2019 ver. 1.1 Remove the case using the Case Removal Guide Sette

www.baratza.com [email protected] rev. 6/6/2019

Pg. 4

APPENDIX: PCB’s with Four Screws

ONLY follow these instructions if your PCB has four screws securing it

Unplug the motor

Remove the 4 screws securing the gearbox/motor assembly.

Remove the assembly.

Remove the 4 screws securing the power board bracket.

Page 5: How to: Power Board Replacement - Baratza...*** Unplug the grinder from power supply *** support@baratza.com rev. 6/6/2019 ver. 1.1 Remove the case using the Case Removal Guide Sette

www.baratza.com [email protected] rev. 6/6/2019

Pg. 5

Lift and remove the power board bracket.

Note wire routing during removal.

Remove the remaining screws from the power board and replace the board.

Inspect wire routing to confirm it is correct.

Page 6: How to: Power Board Replacement - Baratza...*** Unplug the grinder from power supply *** support@baratza.com rev. 6/6/2019 ver. 1.1 Remove the case using the Case Removal Guide Sette

www.baratza.com [email protected] rev. 6/6/2019

Pg. 6

Install the gearbox motor assembly.

Install the new power board, only using the 2 screws towards the rear to secure it to the bracket.

Reinstall the case and return the unit to operation.

If you have any questions or encounter any issues with this guide, [email protected]