How to Operate AAS With SignPal & PhotoPRINT

8/10/2019 How to Operate AAS With SignPal & PhotoPRINT

1/25

How to Operate AAS with SignPal & PhotoPRINT

1. Import the graphic source file. Select the graphics then browse

Effects / Contour Cut to generate contour line.


2/25

22..BBrroowwsseeCCoonnttoouurrCCuuttMMaarrkkttooggeenneerraatteeAAAASSmmaarrkkss..


3/25

3. Select graphics and AAS marks then export as EPS and use

PhotoPRINT or other software to print.


4/25

4. Setup the machine (remove then reinstall CCD cover for pen

installation) and the printed media to be ready(AAS marks must

be set in between the outside pinch rollers).


5/25

55..CClliicckkCCuuttCCoonnttoouurrttoosseelleeccttJJaagguuaarrIIIIIImmooddeellaannddaaddddppoorrtt..


6/25

66..CChhaannggeejjoobbssttaattuussttooHHoollddiinnLLiissttffoorrllaatteerrAAAASSiinnppuutttthheenncclliicckk

SSeenndd..BBaacckkttooPPrroodduuccttiioonnMMaannaaggeerrttoosseelleecctttthheejjoobb.. CClliicckkSSeennddffoorr

AAAASSpprroocceessss..


7/25

77..TThhrroouugghhPPrriinnttppoorrtt,,cclliicckkNNoottooiinnppuuttAAAASSddiimmeennssiioonnddaattaaffiirrsstt

tthheennttuurrnnttoosseettuuppAAAASSoonnppllootttteerr.. Through COM or USBport, do

not respondeither button. Instead, turn to set up AAS on plotter.


8/25


9/25


10/25

9. Select AAS-3-Points \ Set Origin to locate the carriage on (top of

the center of the lower right) AAS markon the printed media.


11/25


12/25


13/25

Warning: Removal of CCD cover during AAS setting will cause

capture error.

1100..SSoommeettiimmeess,,iifftthheemmeeddiiaaiisssseettsslliigghhttllyyooffff,,ccaappttuurreeeerrrroorrmmaayyaappppeeaarr.. BBaacckkttoopprreevviioouusssstteeppffoorrmmaannuuaallsseettuuppttooccaappttuurreetthhiiss

ppooiinntt..


14/25

11. Carriage will return to the origin and be ready for AAS contour

cut.


15/25

Back to Production Manager toselect the same job then send.

ClickYesto output. If through COM or USB port, clickYes on

previous message box.


16/25


17/25

1. Import the graphic source file. Select the graphics then click on

Effects / Contour Cut to ggeenneerraatteeccoonnttoouurroouuttlliinnee..


18/25

2. Click on RIP/Print to output. Select Jaguar III model to add port

setup.


19/25


20/25

3. PhotoPRINT is with both print and cut functions, if users havent

set up printing port, it will show a box to complete this setting.


21/25

4. Back to RIP & Print to change job status to Hold in Listfor later

AAS dimension input and click Send to print out. Click Yes if the

ICC Profiles color correction message box popped up.


22/25

5. Back to Production Manager to select the job under the printer

then click Send.

6. Setup the machine and the printed media (AAS marks must be

located within the pinch rollers on edges).


23/25

7. Back to Production Manager to select the job then Send. Through

Print port, click No to input AAS dimension data, then set up AAS

function on plotter. Through COM or USB port, do not respond

either button. Instead, set up AAS function on plotter.


24/25


25/25

Documents

How to Operate AAS With SignPal & PhotoPRINT