Upload
sudeep-parajuli
View
123
Download
0
Embed Size (px)
DESCRIPTION
This gudie shows you how to install USB dongol and C1 devices
Citation preview
PREPARED BY: Er. Sudeep Parajuli
How to Install a Dongol
Installation Process
1. Insert Cd 2. Click auto run3. Select operating system4. Click next5. Click install6. Click finish and restart the computer
To change to channel 14
1. Go to run( XP) or search bar(win7)2. Type ncpa.cpl3. Choose wireless network connection, RTL8187 ****4. Rt clk , choose properties5. Go to configure6. Go to advance7. Clk Channel Plan and select value MKK18. Clk OK9. Go to realtek icon10. Go to available network11. Select ch 14 AP .. Pw:*****
To install on a Mac book
1. Go to www.broadlink.com.np/downloads (you should be connected to internet by turning wifi on )
2. Clk on “usbdongoldriver”3. Clk on “Mac”4. Clk on “MAC OS X driver and Fix instruction. Zip”5. When downloads complete run the zip file and extract all files.6. Install the driver included in zip file "install.pkg". Ignore the warning about the
corrupt text.7. After reboot, run "realtek USB WLAN Driver Fix mac os x snow leopard.command"
and reboot again.8. After reboot, run "realtek USB WLAN Driver Fix.command".
BROADLINK NETWORK AND COMMUNICATION PVT LTDKESH AND BIDHYA COMPLEX NEWROAD POKHARA
PREPARED BY: Er. Sudeep Parajuli
C1 Installation and Troubleshoot
IP setting
1. Select 'Internet Protocol (TCP/ip v4)' from Local Area Connection and click 'properties'2. Type an IP address of same subnet as that of C1 defult IP i.e 192.168.99.** (Defult Ip of
C1 is 192.168.99.99)3. Use the defult subnet mask '255.255.255.0'4. Clk 'ok' when finish
Check Access
1. Go to "cmd" in 'run'2. Ping 192.168.99.993. C1 should respond to ping in nearly 1 ms if it is properly connected
Configuration
1. Open IE session and type IP of C12. Enter Username and Password to login C1 web access3. System Status will Appear
* Status
* 2.4 GHz association AP
* System configuration
- Ip assignment : DHCP client / Static Ip
- Ip Address : 172.16.4.232
- Subnet Mask : 255.255.255.0
- Gateway Address : 172.16.4.1
4. CLK reboot AP
BROADLINK NETWORK AND COMMUNICATION PVT LTDKESH AND BIDHYA COMPLEX NEWROAD POKHARA
PREPARED BY: Er. Sudeep Parajuli
5. Radio Configuration
- Radio operation mode : CPE /AP
- 2.4 GHz radio
- Wireless mode: 2.4 GHz 54 mbps (802.11 b/g)
- Tx Power : 25
- Max Client : 32
- Distance : 2.0 (0-5 km)
- VAP ID: Edit
- SSID : scan and choose best network
- Lock to AP MAC : remove it
- Channel Scan List : Disable
6. CLK Reboot
To Reboot/Reset C1 device
1. Go to browser and type 192.168.99.99 and press enter2. Under ‘ADMINISTRATION’ clk the option reboot3. Clk ‘reboot device’4. To reset to factory default go to ‘Factory Default’5. Clk ‘Restore to factory default (address retained) if you want to retains ip stored in
device else clk ‘Restore to factory Default ‘6. Reboot the device
Note: There is a pin reset point just next to RJ45 connector in the C1 device. When the device is connected to power supply, push with a pin in this reset point for 10 sec until all light in the device blink once.
BROADLINK NETWORK AND COMMUNICATION PVT LTDKESH AND BIDHYA COMPLEX NEWROAD POKHARA
WAN
LAN
1 LAN
2 LAN
3 LAN
4CPE
POE
CPE/AP LAN
POWER
ROUTER
PREPARED BY: Er. Sudeep Parajuli
How to configure a Router:
Configuration
1. Connect power supply to the router.2. Press power button on the back of the router.3. connect a network cable in any one of LAN port eg LAN1, LAN2...4. See if respective LAN led is glowing or not in front part of router (normally 3
lights should be on).5. Go to network and operation center.6. Choose Local area Connection7. Set the ip of range 192.168.1.***8. Now open a browser, type 192.168.1.19. Go to command prompt and ping 192.168.1.1 to see if it is getting ping in less
than 1 ms.10. Go to wireless settings, Basic settings11. Provide SSID (name of home wifi), mode 11b/g/n mixed, channel autoselect and
save.12. Go to Wireless security option, select the SSID, security mode wpa-psk/wpa2-
psk, select AES and then input preshared key (This will be password for clients who want to connect to this home wifi). Clk save and reboot.
Connection
1. Connect cable coming from LAN of POE (splitter) to the WAN port of router.2. Connect desktop/laptop from LAN port of router to their network port.
BROADLINK NETWORK AND COMMUNICATION PVT LTDKESH AND BIDHYA COMPLEX NEWROAD POKHARA