Embed Size (px)
DESCRIPTION
How to Configure Video Client. This presentation is intended to guide the installer step by step through the Video Client installation. Installing and Operating VDClient. Installing the Video Client Application on the DCN Control PC Installing the Video Client Application on another PC. - PowerPoint PPT Presentation
Citation preview
1 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems DCN Next GenDCN Next Gen
How to Configure Video Client
This presentation is intended to guide the installer step by step through the Video Client installation.
2 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Installing and Operating VDClient
Installing the Video Client Application on the DCN Control PC
Installing the Video Client Application on another PC.
3 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Installing VDClient on the DCN Control PC
Requirements: DCNNG software already installed on the PC LBB4184 (Video Display Software Module) ClientSetup.exe
DCN Control PCLBB4184
ClientSetup.exe
DCN Control PCLBB4184
ClientSetup.exe
4 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 1 Install LBB4184
LBB4184
5 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 2 Install the ClientSetup.exe
6 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 3 Start the DCNNG software
Choose the desired applications
Don’t forget to choose the Video Display Application!
Start the applications
7 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 4 Start VDClient
VDClient is located in the programs list in the Windows Start menu
8 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Menu F12
When starting the application for the first time you will come automatically in the configuration window.
Choose Program runs on DCN Operator PC.
If needed adjust alsoother settings and clickOK
9 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
End of Installing Video Display Software on a Server PC
End of this section.
10 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Installing VDClient on another PC
Requirements : DCNNG software already installed on the DCN Control PC LBB4184 (Video Display Software Module) ServerSetup.exe ClientSetup.exe TCP/IP protocol must have been installed at both PC’s Both PC’s must be in the same workgroup
DCN Control PCLBB4184
ServerSetup.exe
DCN Control PCLBB4184
ServerSetup.exe
VDClientPCClientSetup.exe
VDClientPCClientSetup.exe
TCP/IP
11 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 1 Set IP address of DCN Control PC
12 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 1 Set IP address of DCN Control PC
The IP addres of the DCNControl PC must be set to192.168.100.1
13 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 2 Set Subnet mask of DCN Control Control PC
The Subnet mask of the DCN Control PC must beset to 255.255.255.0
14 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 3 Set IP address of the client PC
15 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 3 Set IP address of the client PC
The IP addres of the DCNControl PC must be set to192.168.100.2
16 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 4 Set Subnet mask of the Client PC
The Subnet mask of the other PC must beset to 255.255.255.0
17 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Technical Tips
If more client PC’s have to be installed the same steps have to made also for those PC’s.
Each client PC must have a unique IP address
IP address 192.168.100.x ( x = decimal value)
All PC’s must have the same Subnet mask 255.255.255.0
18 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 5 Install LBB4184
LBB4184
19 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 6 Install ServerSetup.exe on the DCN Control PC
20 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 7 Install ClientSetup.exe on the client PC
21 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 8 Start the DCNNG software
Choose the desired applications
Don’t forget to choose the Video Display Application!
Start the applications
22 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 9 Start VDServer on the DCN Control PC
VDServer is located in the programs list in the Windows Start menu
23 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Step 10 Start VDClient on the Client PC
VDClient is located in the programs list in the Windows Start menu
24 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
Menu F12
When starting theapplication for the firsttime you will come automatically in the configuration window.
Choose Program runs on an external PC.
Fill in the Network nameof the DCN PC
If needed adjust alsoother settings and clickOK
25 DCNNG VC IO ST/PRM3-EU | |02.Mar.06 © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of
disposal such as copying and passing on to third parties.
Security Systems
How to Configure Video Client
End of section
Main Menu
