How Can You Transfer a WinCC Flexible Project Serially to a Panel

Embed Size (px)

Citation preview

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    1/10

    How can you transfer a WinCC exible project serially to a panel?

    Display part number

    Instructions:For the serial transfer of a WinCC exible conguration you must make settings on the

    panel and in WinCC exible.

    Note:There are four dierent cables ith hich you can make a serial pro!ect transfer"

    #ero modem cable

    $%& host'to'host cable

    (%)*)+,,- multimaster cable

    $%&+,,- multimaster cable released as from /E-Stand !/ and WinCC exible

    )001 S"#2

    Notes:

    With 3icro ,anels you can transfer a pro!ect only4ia a ,,- multimaster cable.

    ,lease refer to the rele4ant manual of each operator panel or 5ntry

    -D" 67607809for information on hich cable can be used for hich panel.

    -f you ish to integrate your conguration ,C in an existing ""I networ$: for

    example: you must transfer the netork parameters. ,lease note that the node

    address of the ,C in thenetwor$must be uni;ue.

    Settin%s on t&e operator panelThe gures belo are from the T,6

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    2/10

    serial

    & $%&+,,- multimaster cable

    C #ero modem cable

    D $%& host'to'host cable )

    Table 06

    Note:3icro ,anels do not support pro!ect transfer 4ia $%& host'to'host cable or >eromodem cable.

    )a

    (ersions )* +* C - ,ulti,aster cable and ero ,ode, cable

    Settin%s in .Control "anel.-f you ish to transfer a pro!ect using a $%& host'to'host cable: you can skip thispoint and go directly to,oint )b.

    -n the case of some operator panels e.g. T,6

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    3/10

    A @& 2Fig. 0) ' Transfer %ettings

    Note:The /(emote Control/ option permits automatic termination of (untime on thepanel hen transfer is triggered 4ia the de4elopment en4ironment of WinCCexible. The panel then automatically sitches to Transfer mode.

    )b

    (ersion 1 - 2S+ &ost-to-&ost cable

    Settin%s in .Control "anel.-f you are using a multimaster cable or >ero modem cable: you can skip this pointand go directly to ,oint *.

    = special dri4er is needed for transfer ith a 2S+ &ost-to-&ost cable. Thisdri4er is on the WinCC exible -nstallation CD under /C13or C14B %upport BDe4iceDri4er B $%& BWin3or Win5"/. 3ore information on ho to installthe dri4er: for example: is a4ailable in 5ntry -D6768)0*8.

    ?pen the /ransferdialog in the /Control ,anel/.

    7 @& 2Fig. 0* ' Control ,anel

    Transfer ith the $%& host'to'host cable is enabled in Channel ). For Channel )you select the entry /$%&/. For C&annel 3you also set a check mark for /5nableChannel/ and if you ish: /0e,ote Control/.

    81 @& 2

    http://support.automation.siemens.com/WW/llisapi.dll?func=ll&objid=23787153&nodeid0=16502685&caller=view&lang=en&siteid=cseus&aktprim=0&objaction=csopen&extranet=standard&viewreg=WW#Marke2http://support.automation.siemens.com/WW/llisapi.dll?func=ll&objid=23787153&nodeid0=16502685&caller=view&lang=en&siteid=cseus&aktprim=0&objaction=csopen&extranet=standard&viewreg=WW#Marke2http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&objId=19142034&objAction=csOpen&nodeid0=16502685&lang=en&siteid=cseus&aktprim=0&extranet=standard&viewreg=WWhttp://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&objId=19142034&objAction=csOpen&nodeid0=16502685&lang=en&siteid=cseus&aktprim=0&extranet=standard&viewreg=WWhttp://support.automation.siemens.com/WW/llisapi.dll?func=ll&objid=23787153&nodeid0=16502685&caller=view&lang=en&siteid=cseus&aktprim=0&objaction=csopen&extranet=standard&viewreg=WW#Marke2http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&objId=19142034&objAction=csOpen&nodeid0=16502685&lang=en&siteid=cseus&aktprim=0&extranet=standard&viewreg=WW
  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    4/10

    Fig. 08 ' Transfer %ettings 3,*

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    5/10

    connection.

    97 @& 2Fig. 01 ' Connections

    )a

    (ersion ) - Non-inte%rated project

    1e6ne para,eters-f you ha4e created an inte%ratedWinCC exible pro!ect or ould like tointegrate it into %T5,

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    6/10

    )b (ersion + - Inte%rated project

    1e6ne t&e station-f you are not using an integrated pro!ect: you can skip this section and go

    to ,oint *.oucannotintegrate 3icro ,anels into %T5,

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    7/10

    A7 @& 2Fig. 09 ' Connect station

    Close the dialog indo ith /?@/.

    %a4e and compile your conguration 4ia the menu /Networ$ 7 Sa9e

    and co,pile'''/.

    Where applicable: transfer your changed hardare conguration to all the

    rele4ant %-3=T-C stations and terminate Eet,ro.

    Gia the corresponding subnet you select the station ith hich the

    operator panel is to communicate.

    76 @& 2Fig. 07 ' %elect station

    *

    "roject transfer

    ?pen the dialog indo under /"roject 7 /ransfer 7 /ransfer

    Settin%s'''/. =lternati4ely you can also open the transfer settings 4ia thetoolbar 62.

    -n the /Transfer %ettings/ dialog you select the rele4ant operator panel )2' only necessary in the case of multiple operator panels.

    %elect the desired Transfer mode see Table 0)2. -n the case of the

    Transfer mode /%erial/ you must also dene the C?3 interface and thebaud rate.

    Note:

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    8/10

    For the possible transfer options please refer to the rele4ant manual or5ntry -D"67607809.

    With the /Transfer/ button 82 you can no transfer your conguration to

    the panel.

    667 @& 2Fig. 60 ' ,ro!ect transfer

    Note:-f pro!ect transfer is not possible ith WinCC exible: then check the folloingpoints"

    ,hysical connection beteen conguration ,C and operator panel replace

    cable if necessary2.

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    9/10

    * (%)*)+,,- multimaster cable %erial

    8 #ero modem cable

    Table 0)

    Note:

    -f you do not ant to transfer yet: you can sa4e the settings ith /=pply/. Withthe 6rsttransfer of the pro!ect to an operator panel you should disable the/Delta transfer/ and enable the /?4errite passord list/ option.

    Note:=fter transfer the panel adopts the parameters set in the /Connections/ tab.

    Settin%s on t&e 2S+=""I ,ulti,aster cable:The $%&+,,- multimaster cable /5'%tand 01/2 doesnHt ha4e any D-, sitches and can

    be used for pro!ect transfer as fro,WinCC exible )001 %,6.

    Settin%s on t&e 0S343=""I ,ulti,aster cable:

    Cable 1I" switc&

    (%)*)+,,- multimaster cableFor pro!ect transfer you must set the 6ft& 1I"

    switc&to the

  • 7/24/2019 How Can You Transfer a WinCC Flexible Project Serially to a Panel

    10/10

    /WinCC exible )001 Communication ,art 6//WinCC exible )001 Communication ,art )/

    5ntry-D" 69