Upload
hix-corporation
View
138
Download
4
Embed Size (px)
DESCRIPTION
2012 SCREEN PRINT AND DRYING/CURING EQUIPMENT MADE IN THE USA ABOUT THE COMPANY INSIDE Certified Green Educational Material Screen Print Shop Packages Exposure Units Registration System Screen Dryer Washout Booth Rotary Printer Bench Printer Printer Conveyor Oven Combo Retensionable Frames Screen Printing Accessories Conveyor Ovens Electric Dryers/Ovens Gas Dryers/Ovens Flash Cure Units Gel Cure Oven Direct to Garment Ovens Vertical Ovens
Citation preview
2
From art to screen prep & exposure, to press setup & printing, you too can master the art of screen printing. It is easy, fun & profitable. Our simple to use, easy to understand training manuals with accompanying DVD’s will en-hance your knowledge and help give you the confidence to make great images through screen printing.
Here is what you get, 1 set of 3 lesson guides & 5 DVD’s. Our individual study guides are built around 3 areas of expertise. 1. Art Preparation. 2. Screen Preparation & Exposure. 3 The Screen Printing Process. All in full color. We walk you through the guide step-by-step, starting with the featured lesson and objective, outlining the Tasks, Material & Supplies required, Vocabulary & Out-side Reading Reference. Our DVD’s follow the lesson guides even the guide book photos are the same as the DVD. At the end of each lesson is a short quiz. There are 35 lessons in all, 114 pages filled with screen printing exper-tise.
Our 1st Guide & DVD takes you through 48 pages of Art Basics using the com-puter to create a graphic though color separation. Our 2nd Guide & 2 DVD’s,
on screen preparation & exposure, is 35 pages & covers exposure and washout, screen preparation & image alignment. Finally, our 3rd Guide & DVD takes you through 31 pages of step-by-step instructions from taping/preparing your screen for ink loading, registering the screens & on to printing through clean up. These easy to use study guides follow the DVD’s page by page so you can learn at your own pace.
INSIDE
About HIX Corporation
Educational Tools
HIX Corporation, located in Pittsburg, KS, has been a pioneer in the design and manufacture of quality products for the Screen Print and Graphic Transfer Industries since 1963. HIX Corporation was started by the Hix brothers to produce their Textile Conveyor Dryers.
Purchased in 1989, HIX has continued to expand their product line to include a full line of Heat Transfer Machines, Screen Printers, Screen Frames, Industrial Ovens, and Commercial Food Equipment includ-ing Pizza and Tortilla Presses. HIX products can be purchased world-wide through distribution networks.
HIX is a world leader in the design, development, and distribution of equipment for the Screen Print, Industrial Dryer, and Commercial Food Equipment industries with it’s 110,000 square foot manufacturing facility including integrated aluminum foundry, CNC mill operation, welding, metal forming, wiring, fabrication, assembly, and packaging departments.
Finally a quality, simple, easy to use way to learn The ART of Screen Printing!1 set of 3 lesson guides•
Art Design & Prep1. Screen Prep & Exposure2. Press Setup & Printing3.
5 DVD’s•
Shop packages ............................................................ Page 3Exposure Units ............................................................ Page 4Registration ................................................................. Page 5Screen Dryers.............................................................. Page 5Washout Booths .......................................................... Page 5New Premier Printers ............................................... Page 6-7Retensionable Frames ................................................ Page 8
Printer Accessories ...................................................... Page 9Electric Dryers ...................................................... Page 10-12Flash Cure Spot Heaters ........................................... Page 13Gel Cure Ovens ......................................................... Page 13Gas Dryers ................................................................ Page 14Direct to Garment ...................................................... Page 15Batch Ovens .............................................................. Page 15
3
HIX Premier Shop Equipment Includes:HIX New Premier NPII 2410 24” wide 220v conveyor dryer with air circulation• HIX SH-1818 automatic 18”x18” 120v spot heater• HIX NP 6 color, 4 station rotary screen printer with micro registration• HIX Halux-1200D hot strike 1200 metal halide digital 120v screen exposure unit• 16 HIX retensionable screen frames 21”x23” O.D. (optional prestretched frames shown) and tool kit• Optional 6 color HIX King Pin • ™ 1,2,3 registration system
HIX Pioneer Shop Equipment Includes:HIX E-2408 24” wide 220v conveyor dryer• HIX MSH-1818E 18”x18” 120v spot heater• HIX NP 4 color, 4 station rotary screen printer with micro registration• HIX TT-180D digital table top fluorescent UV 120v exposure unit• 12 HIX retensionable screen frames 21”x23” O.D. (optional prestretched frames shown) and tool kit• Optional HIX King Pin • ™ 1,2,3 registration system in 4 or 6 color
HIX Complete Shop Packages
HIX Little Pro Shop Includes:HIX E-2255 22” wide 120v conveyor dryer• 4 color, 1 station printer with micro registration• HIX TT-110E table top 120v exposure unit• 4 HIX retensionable screen frames 21”x23” O.D. • and tool kit
HIX Starter Shop Equipment Includes:HIX E-2408 24” wide 220v conveyor dryer• HIX MSH-1818E 18”x18” 120v spot heater• 4 color, 1 station printer with micro registration• HIX TT-180D digital table top fluorescent UV 120v exposure unit• 4 HIX retensionable screen frames 21”x23” O.D. and tool kit•
All HIX Equipment Comes With A Standard 1-Year Warranty.*The HIX Halux-1200D, TT-180D and TT-110E are not compatible with the M&R Trilok pin registration system.
4
1-800-835-0606 www.hixcorp.com
TT-180D FEATURES
TT-110E FEATURES
Halux™1200D FEATURES
Table top design measures 40”W x 31”D x 8”H• Maximum exposure area: 23” x 31”• 6 - 30 watt high output Aqua Coral fluorescent UV lamps.• Auto-reset timer, cycle start switch, vacuum power switch, • and main power switchDurable deep draw rubber blanket• 120v, 5A, 60Hz• Vacuum pump: 115v, 3A, 60Hz• Optional let kit•
Table top design measures 27.75”W x 27.75”D x 5.5”H• Maximum exposure area: 23” x 25”• 4 - 14 watt high output Aqua Coral fluorescent UV lamps.• Power switch• Durable rubber blanket• 120v, 5A, 60Hz• Optional leg kit•
1200W metal halide lamp.• Hot restrike eliminates shutters.• 24”x42” exposure area.• Safety vacuum interlock.• Filtered air removes heat and keeps dust out.• Deep draw blanket.• Premium oilless vacuum pump.• 48”Wx35”Dx42”T, 381 lbs.• 120V: 20A, 2400W, 60Hz. 230/240V: 10A, 2400W, 50 Hz.• 120V requires NEMA 5-20P 20A Outlet.•
The speed of Ultra High Intensity Metal Halide Halux™ 1200D allows you to get from the art room to the printing press quickly, easily and affordably. The single-point metal halide light source holds fine lines and produces better halftone images, providing accurate exposures. Our powerful 1200W metal halide lamp warms up in less than one minute. This “Hot Restrike” feature, eliminates warming time between exposures, saving electricity and extending bulb life. No assembly is required.
The TT-180D & TT-110E table top exposure units are compact, low cost and efficient. They provide clear exposure of fine lines, half tones and detail work. Powered by high output Aqua Coral UV florescent lights, TT-180D and TT-110E give you a full range of exposure capabilities at an economical price.
Halux™ 1200D
TT-180D
TT-110E
Digital Display
Hot Restrike uses less energy
EXPoSurE unITSHALuX™ 1200D - Metal Halide, TT-180D & TT-110E - Florescent u.V.HIX Exposure Units are built on years of experience and quality.*The HIX Halux-1200D, TT-180D and TT-110E are not compatible with the M&R Trilok pin registration system.
5
www.hixcorp.com 1-800-835-0606
4 and 6 color kit includes mounting plates,1 hole punch, 1 exposure plate
pin on press aligns with
hole in screen frame for quick screen
mount
with KInG PIn™ 1,2,3 rEGISTrATIon SYSTEM
SCrEEn DrYEr
WASHouT BooTH
Innovative angle rack system, with self leveling • configuration eliminates movable parts.Filtered Air prevents pin holes.• Slotted air knives provide even heated air to every • frame.8 fully adjustable frame rails for screens up to 26” x 32”.• 1,600 watts / 5,400 BTU, 14 amps / 120 volts; • designed for fast drying.Air circulation system removes moist air displacement • the at rate of 200 cfm. Separate fan & heat switch.• Galvannealed interior resists corrosion.• 120V also available in 220V• 36” x 38” counter top perfect for screen stretching • surface or table top exposure unit.
ExposurePlates
Do what the pro’s do, cut down on touch ups, eliminate pin holes, get consistent emulsion cure, dry screens in minutes not hours
Our Washout Booths offer the best Size, Quality & Value
Step2
Step1
expose artin registration
design then hole punch art in registration
38”36”
36”
10° sloping bars eliminate mesh
contact with shelf.
Specs
Measures:32” Booth: 32”W x 24”L x 64”H 36” Booth: 36”W x 24”L x 69”H
Specs:
Dryer dimensions: • 38”W x 36”D x 36”HShipping dimensions: • 49”x41”x44”Shipping weight: 231 lbs.•
Create design in registration, Expose in registration, Print in registration
mount frames in registration
Step3
Step 1. After creating your own film positives or vellums, punch two holes with supplied King PIN hole punch
Step 2. Expose with the King PIN exposure plate, then mount the King PIN print head mount plate, to the printer. Now you are ready to print in perfect registration.
Step 3. Mount frames in alignment.
Reten frames are 100% compatible with the King PIN™ registration for any HIX printer.
A Washout Booth is an essential part to any clean-room. Our 32” and 36” Washout Booths are made of durable, chemically resistant 1/4-inch natural poly and features built-in screen supports and a perforated drain. Both size Washout Booths can hold a standard 23”x31” frame. The 36” Washout Booth’s larger size provides an extra four inches in width and five inches in height. Best of all, the 32” and 36” Washout Booths employ the same innovative multipart system that allows them both to be disassem-bled and shipped via UPS ground in one box.*optional Backlight Available
Welded main pan• Locking side and back panels• Built-in screen supports• 1/4-inch natural polypro construction•
Easy to backlight• Easy to assemble• Bolt on legs• Ships regular UPS ground•
6
Sequential Lift ProvidesLevel On-Contact
Registration
The true “all-heads-down” feature allows printing any color • at any/multiple stations simultaneously.Standard X,Y,Z micro registration.• Standard with 15”x15” wood boards and back screen clamp.• Expandable from 1 to 6 colors and 1 to 6 stations.• Optional side clamps or larger “Bigfoot• ™” side clamps for extra large frames.The HIX NP Premier Printer is the fastest manual screen • printer in the world, the result of 48 years of engineering excellence. King PIN• ™ Pin Registration compatible.
Screens are leveled and ready to print in seconds.• Full range of interchangeable platens: from jacket hold-• downs, sleeve boards, youth as well as custom aluminum boards are available.Faster and easier cleanup with aluminum print heads and • zinc plated finishes.Custom, large format and 8 color presses available.• Gas lifts, NO SPRINGS!• Rotary stop alignment.• Totally tool-less, on/off contact and inclination adjustments.• Tapered Roller bearings.• Air assist screen lift system available.•
TotallyTool-less
nEW PrEMIEr roTArY PrInTEr
RUggED ADjUSTABLE
BASE
ZINCPLATEDSTEELARMS
X,Y,ZMICRO
REgISTRATION
FullyExpandable1-6Colors•1-6StationsThe BEST printer in the industry, just got better. Aluminum cast components, true all heads down printer, state-of-the-art micro registration and pin registration systems.
Optional Aluminum Platens
Optional Side Clamps
Six Color Printer
Silky SmoothMicro Registration
X,Y and Z AxisMovement
=Precision!
1-800-835-0606 www.hixcorp.com
1 color bench 4 color bench4 color /4 station rotary
6 color /4 station rotary
21 in/53 cm 53 in/135 cm 96 in/244 cm 96 in/244 cm
39 in
/99
cm
70 in
/178
cm
96 in
/244
cm
96 in
/244
cm
Printer Dimensionsnot to scale
Smooth Operationgas Shock Lift
gold Zinc Plated Finish
7
nEW PrEMIEr BEnCH PrInTErS1-4 Color Rotary or Single 1 color
These printers can be placed on a • bench top, table or mobile cart sys-tem and have a totally tool-free design with on/off contact and incli-nation adjustments built right into the press.HIX Premier bench printers also • feature 12” screen back clamps, 15”x15” removable wood shirt board, squeegee rest and gas lifts. Add a HIX vacuum platen; perfect • for printing decals, licence plates, transfers and more.
www.hixcorp.com 1-800-835-0606
Print Print Popular Models Heads Stations Unit Maximum Screen Shipping Name/Number (Colors) (Platens) Diameter Width (O.D.) Weight 1c/1s Bench 1 1 39” (99 cm) 21” (53 cm) 138 lbs. (63 kg) 4c/1s Bench 4 1 70” (178 cm) 28” (71 cm) 173 lbs. (79 kg) 4c/4s Floor Rotary 4 4 96” (244 cm) 28” (71 cm) 424 lbs. (193 kg) 6c/4s Floor Rotary 6 4 96” (244 cm) 21” (53 cm) 475 lbs. (216 kg) 6c/6s Floor Rotary 6 6 100” (254 cm) 21” (53 cm) 552 lbs. (250 kg) LF 6/4 Rotary* 6 4 100” (254 cm) 25” (64 cm) 555 lbs. (252 kg) LF 6/6 Rotary* 6 6 100” (254 cm) 25” (64 cm) 610 lbs. (277 kg) Big 8 Floor Rotary 8 8 116” (295 cm) 21” (53 cm) 1107 lbs. (502 kg) Over 40 configurations available
4 Color Bench PrinterShown with optional side clamps and vacuum platen
optional vacuum platen
1 Color Bench Printer
Start with a HIX bench printer; add
on more print heads and stations later to expand to the floor model.
Totally modular and expandable to a floor rotary printer. With all the same features:
Aluminum cast components.•Micro registration.•Sequential lift.•
Popular options available for HIX printers:Youth boards.•jacket attachments.•Cap attachments.•Dual sleeve/leg boards.•Aluminum boards.•Side clamps.•
See all our printer options on page 9.
All Premier Printers come standard with 15”x15” wood boards, back clamps, micro registra-tion, gas lifts and tool-less adjustment. See all our additional options on page 9.
gAS LIFTNO SPRINgS!STANDARD
*Includes Air Assist System
This combination printer/conveyor oven provides the perfect solution for shops tight on floor space. The neatly placed, 4 color 1 station printer sets on top of the compact HIX E-2255, a 120v, 22” wide by 5.5’ long conveyor oven. The printer offers the same features as the time tested Premier printers; micro-registration, gas lifts and rotary stop alignment. The printer is totally expandable.
LITTLE Pro CoMBo PrInTEr/ConVEYor oVEn
8
rETEn® SQuArE rETEnSIonABLE FrAMESFor Textile and graphic Screen Printing Applications.
Square sidebars won’t twist/warp like roller frames. They clamp easily into any printer • without adapters, saving time & money. No edge protectors needed; there is no exposed fabric wrapped around our sidebars. • Pre stretched retensionable frames also available in 61, 110 & 158 white mono polyester mesh on 21”x23” & 23”x31” frames.• Retens tape and handle like wood or welded aluminum frames. There’s no need for fabric protectors or special stretching • tables.The Fastrax system is the quickest “fabric to frame” technique available on any frame. There’s no presoftening. Corners can be • softened at any time during tensioning or retensioning. Our color coded dual spline fabric locks easily in our continuous slot. No more damaged mesh from inferior end threading systems.Tension control means quality control. Dual tension jacks provide infinite fabric tension adjustments in each image area quad-• rant. You get consistent, controllable mesh tension and higher print quality with no thread distortion.If you “opposite gang run” pocket prints you can rotate and reposition Retens in seconds.•
The patented HIX Reten® frame offers the most advanced features in frame technology. You’ll save both time and money with our square sidebars, Fastrax™ mesh mounting system and Accutrax™ Tensioning. You’ll also increase your mesh life 7 times or more while reducing your ink consumption by 20% or more.
1-800-835-0606 www.hixcorp.com
EASY CLEAN
CHANNELS
SIMPLE AND EASY
TO USE TENSIONjACKS
CLEARANODIZEDCOATINg
Corner Dams
Dams prevent the ink from being pushed into the corners. This makes it easier to clean the screens. Time saver.
Keeps screens
tight!
Ask about our RetenTool Kit! Comes with Reten
DVD Simple Training Video.
Sizes range (Whole inch only)
M (Manual Press) 1.5”x1.25” Channel ........................10" - 27" OD.M/A-40 (Manual/Auto Press) 1.5”x1.25” Channel ......10" - 31" OD. A (Automatic Press) 1.5”x1.5” Channel .....................15" - 36" OD. LF (Large Format Press) 2”x1.5” Channel .................28" - 55" OD. Custom Frames ....................................................................... CALL. Toolkit ...........................2 Tension Jacks, Ratchet, Spline Tool, DVD.
EASYINSERTION
SPLINES
•RecycleMesh•LongerMeshUse
•NoWood
Frame Types
NEW!Pre Stretched
Framesshown with optional
corner dams
9
PrInTEr ACCESSorIES
Shirt Board with or without bracket: •11”x17”Wood•10”x15”YouthWood•15”x15”Wood•16”x17”Wood•4”x17”SingleWoodSleeve•14”x14”Aluminum•16”x17”Aluminum•18”x22”Aluminum•8”x14”Aluminum•10”x14”Aluminum•16”x20”Aluminum•Custom(call)
•ShirtBoardBracket•DualSleeveBoard 4”x14”Aluminum•DualSleeveBoard 4”x18”Aluminum•VacuumBenchVacuumPlatenandPump•JacketHold-down 16”x16”•SportShortsHold-down7-1/2”x7-1/2”•JacketHold-down 14”x14”Deluxewithpad•CapAttachment•StandardSideClamps•“BigFoot™”LargeFormatSideClamps•Crosstubefrom19”to36”•AirAssistKit4-6-8color•KingPin™ 1,2,3 Registration
Printer Accessories - Call 1-800-835-0606 to learn how to expand your printer!
CustomizeYour
Printer!
All specifications subject to change without notice.
Air Assist Screen Lifting mechanism is especially useful with heavy/over-sized screens or long runs. It greatly reduces operator fatigue while it increases production. Air pressure needed to lift various size screens is fully adjustable.
• Custom• Oversize
• Youth • Sleeve/Leg Boards
4”x14” and 4”x18”.
The jacket attachments holds jackets tight for pre-cise multi-color print regis-tration. Doubles jacket printing production! And, adjusts for different jacket thicknesses in less than a minute. Print area dimen-sions are:7.5”x7.5”, 10”x10”, 14”x14” and 16”x16”.
Cap Attachment & Bracket
Aluminum Shirtboards offer years of use and are per-fect for flash cure.
and custom sizes
Shirtboards can be ordered with or without neck placement guides.
HIX 16” X 17” Wood & Aluminum Shirtboards are perfect for oversized prints on XL and XXL shirt sizes.
Boards have a white melamine surface and bracket attached to the backside for easy mount-ing to the HIX NP Printer.
The Vacuum Platen attach-ment for NP Printer makes transfer printing production easier, faster, more quiet and accurate than ever. Redesigned, allows print-ing on flat substrates (transfers, decals, bumper stickers, licence plates and more). Outside platen dimensions are 15 3/8”x22” with print area dimensions of 13”x17”.
Regular side clamps grab and hold your frames,
keeping them in tight registration.
Bigfoot Side Clamps for those jumbo prints such as towels, aprons and all over
prints using extra large frames.
Air Assist Screen Lift
Custom DesignedAluminum Shirtboard
jacket Attachment
Cap Attachment
Aluminum Shirtboards
Sleeve boards
Vacuum Platen
Side Clamps
Air
(Press, screen, props and squeegee not included)
10”x14”
14”x14”
16”x17”16”x20”18”x22”
10
1. Determine inside oven length (dimensions page 11).2. Determine number of items oven will hold,
i.e. 18”/item on 10’ belt = 6 items/cycle.3. Determine cycles per hour. This depends on cure times of the ink.
(See cure time examples) Divide cure time into 60 minutes to get cycles per hour.
CURE TIME EXAMPLES:Plastisol Inks -90 seconds (40 cycles/hr)Water-Base Dyes -2 minutes (30 cycles/hr) Nylon Inks - 60 seconds (60 cycles/hr)
4. Multiply number of items the oven can hold (Step 2) by the number of cycles per hour (Step 3). Divide by 12 to obtain dozens per hour.
EXAMPLE: 24” wide 10’ oven chamber curing plastisol inkSTEP 1 - 10’ oven = 120”STEP 2 - 120” ÷ 18” print = 6 items per cycleSTEP 3 - 60 minutes ÷ 90 seconds (plastisol cure time) = 40
cycles per hourSTEP 4 - 6 shirts X 40 cycles per hour = 240 items per hour.
240 ÷ 12 = 20 dozen units per hourNOTE: Pretest all cure times.
Digital Temp Control
Energy Saving
Adjustable Entry/Exit
Doors
Heater Diagnostic Panel
HIX Heater
Relay Display Lights Belt Speed
Air Speed Control
True TrackBelt Rollers
AdjustableBelt Rollers
OptionalWheel Kits
Filtered Air Cooled Control PanelExhaust Motor
Air Recirculating External Mount Electronics keeps components cool
Variable Speed
Belt Motor/Belt Drive
HIX Manufactures all heaters for the exact Watt Density and Maximum Energy Balance
HIX nPII DrYEr FEATurESAsk about our BE-II Series Dryers
Calculating Your Production Needs:
Choice of the Direct To Garment World!
•Useslessenergy•Betterinsulation
•RecirculateshotairPower exhaust from the bottom• VFD Speed Control• For Max Energy Efficiency• Max Air Flow for waterbase or • Plastisol Inks
11
DIRECT TO gARMENT PREFERRED
HIX nEW nPII PrEMIEr ELECTrIC DrYErS
Dryer DimensionsNPII and BEII Models
HIX dryers offer the most efficient drying technology available.The sleek low profile design and side mount control • panel, includes an analog variable belt speed control-ler, thermostatically controlled oven temperature, digi-tal heat controller, and a variable air speed controller to adjust air flow volume within the oven chamber.The interior walls of the oven are fabricated from cor-• rosion resistant galvanized steel to resist attack from moisture, volatiles, and corrosives released from sub-strates and inks. Newly designed with the bottom mounted exhaust sys-• tem and front mounted control box allows the top of the dryer to be removed for easy access to the heater panels and for interior oven cleaning. The top and sidewalls are insulated with 2” thick high • temp ceramic insulation for optimum energy efficiency. Enjoy savings on your electric bill with a HIX NPII Dryer and higher production drying speeds. Variable speed air recirculation allows for up to 97% • recycled air. The precise control system of analog belt speed and • digital temperature controls give you the ability to choose the correct combinations for differing prod-ucts. The heavy-duty belt drive has a variable speed motor • with positive chain drive. This system also has perma-nently lubricated ball bearings at all rotation points for smooth, trouble free service.
30 in/76 cm
6 ft/
183
cm
1806
41 in/104 cm
10 ft
/305
cm
2410
51 in/130 cm
10 ft
/305
cm
3610
51 in/130 cm
16 ft
/488
cm
3616
51 in/130 cm
19 ft
/579
cm
3619
66 in/168 cm
19 ft
/579
cm
4819
* The above models are also available with analog controls in our BEII series. Call for details, 800-835-0606
RecirculatingAirflow:Exhaust Duct:
Rated Exhaust Flow:Amp at 220V/Phase:
KW at 220V:BTU:
Length:Width:
Height:Belt Width:
Oven Length:Entry Length:
Exit Length:Belt Height:
Volt-VAC:
N/A4” (10 cm)
49 cfm15A/1
2.8 KW9,700
6’ (183 cm)30” (76 cm)45” (114 cm)18” (46 cm)42” (107 cm)15” (38 cm)15” (38 cm)32” (81 cm)120 or 220
1300 cfm3” (7.5 cm)
130 cfm45A/18 KW
27,28010’ (305 cm)41” (104 cm)46” (117 cm)24” (61 cm)60” (152 cm)30” (76 cm)30” (76 cm)32” (81 cm)
208-240
1300 cfm3” (7.5 cm)
130 cfm32A/3
10.8 KW36,825
10’ (305 cm)51” (130 cm)46” (117 cm)36” (91 cm)60” (152 cm)30” (76 cm)30” (76 cm)32” (81 cm)
208-240
1500 cfm4” (10 cm)216 cfm50A/317 KW57,970
16’ (488 cm)51” (130 cm)46” (117 cm)36” (91 cm)96” (244 cm)48” (122 cm)48” (122 cm)32” (81 cm)
208-240
3000 cfm5” (12.5 cm)
326 cfm70A/3
22.9 KW78,000
19’ (579 cm)51” (130 cm)46” (117 cm)36” (91 cm)
132” (335 cm)48” (122 cm)48” (122 cm)32” (81 cm)
208-240
3000 cfm5” (12.5 cm)
326 cfm95A/3
32.2 KW110,000
19’ (579 cm)66” (168 cm)46” (117 cm)48” (122 cm)132” (335 cm)48” (122 cm)48” (122 cm)32” (81 cm)
208-240
Dryer Model: NPII-1806 NPII-2410 NPII-3610 NPII-3616 NPII-3619 NPII-4819
For our full-line of products please visit us online!
12
HIX EA/E DrYErS
N/A
3” (7.62 cm)
N/A
18.5A
2.2 KW
7,502
5.5’ (165 cm)
31.25” (79 cm)
49.5” (126 cm)
22” (56 cm)
26” (66 cm)
30” (76 cm)
17.5” (44 cm)
17.5” (44 cm)
34.5” (165.1 cm)
120
N/A
10” (25 cm)
400 cfm
32A/1
6 KW
20,630
8’ (244 cm)
30” (76 cm)
54” (137 cm)
24” (61 cm)
42” (107 cm)
54” (137 cm)
20” (51 cm)
20” (51 cm)
32” (81 cm)
208-240
55 cfm
10” (25 cm)
400 cfm
35A/1
6 KW
20,630
10’ (305 cm)
32” (81 cm)
58” (147 cm)
24” (61 cm)
60” (152 cm)
72” (183 cm)
24” (61 cm)
24” (61 cm)
32” (81 cm)
208-240
135 cfm
10” (25 cm)
400 cfm
28A/3
9.1 KW
31,000
10’ (305 cm)
44” (112 cm)
58” (147 cm)
36” (91 cm)
60” (152 cm)
72” (183 cm)
24” (61 cm)
24” (61 cm)
32” (81 cm)
208-240
265 cfm
12” (30 cm)
700 cfm
45A/3
14.2 KW
48,540
16’ (488 cm)
44” (112 cm)
58” (147 cm)
36” (91 cm)
96” (244 cm)
108” (274 cm)
42” (107 cm)
42” (107 cm)
32” (81 cm)
208-240
RecirculatingAirflow:
Exhaust Duct:
Rated Exhaust Flow:
Amp at 220V/Phase:
KW at 220V:
BTU:
Length:
Width:
Height:
Belt Width:
Oven Length Inside:
Oven Length Outside:
Entry Length:
Exit Length:
Belt Height:
Volt-VAC:
E-2255 E-2408 EA-2410 EA-3610 EA-3616Dryer Model:
HIX EA/E dryers are great for smaller screen printing shops or for those who are looking for an economy priced dryer.The dryers are built with the same HIX standard for quality and reliability. Provides all of the basic needs to cure plastisol inks.The dryers are not recommended for high moisture/waterbased inks. The HIX Premier models are better suited for these applications.
HIX EA/E Dryer Features Include:High performance, long lasting infra-red • heat panels built by HIXCirculating single speed air system • (not included on E-2408 or E-1806)Belt speed and heat controls• Fiberglass belt•
Energy Saver•TriplewallonE-2408.•Thermocouplecontrol.
Exhaust Fan
Belt MotorTemperature
ControlBelt Speed
Control
Simple Controls
Fume hoods can be added-on to the exit side, entry side or on both ends of any dryer. The fume hood operates separately from the dryer controls and includes an independent on/off switch. It is equipped with a 50 cfm exhaust fan, a 4” duct opening and sepa-rate power cord. Available in 120 volt (1 Amp) and 220 volt (0.5 Amp).
Heavy Moisture Smoke Fume Discharge?optional Fume Hood
Improve Shop Air Quality
Sizes - 14.8” H x 8.9” L x 32” W (24” Oven) “ “ 44”W(36”Oven) “ “ 56”W(48”Oven) “ “ 69”W(60”Oven)
13
FLASH CurE GEL CurE unITS
All the best features in our top of the line air spot heater.
New thermocouple design temperature control.• Manual foot control. • Auto/cycle swingaway heat head, for fast, • hands free flash. Fan assist air circulation, through the heat head • for fastest flash or delicate substrates such as nylon.Heat “Sink” in ready position saves money and • 70% of heat.Full range temperature control for all your sub-• strates. Digital LED display, dwell timer.• Wheels for easy positioning•
HIX has developed an exciting new product for narrow web, multi-color print operations. The HIX Thermatrol Gel / Cure Unit is designed to replace vertical web dryers used between individual color print sta-tions. This unit is perfect for gelling, pre-curing, and post-curing inks of various composi-tions. It is used with continuous roll to roll web printing or screen printing.Capital expenditures and operating costs are significantly lower than with conven-tional web dryers. Units custom designed to meet custom-er’s process needs.
gel Cure Features Include:Multiple zones of digital temperature con-• trol. Operating temperatures of up to 350°F. • Airflow directed from the top downward • onto the web which gives quicker, more efficient curing operation. Two HIX exclusive CritiSense, non-contact • sensors for accurate, instantaneous control of the process. Custom sizes and wattages to meet your • process requirements. Custom designed temperature capacities • meet user process flow requirements. Compact size of 46” x 25” for an 18 inch • web on GC-4800 model. Custom designed models available in web • widths up to 6 foot. 8” exhaust duct with bottom exit. • 240 / 480 volt, 3-phase.•
SH-1818 - 18”x18” (46cm x 46cm)Same great features as our ASH models without the • fan air assist.
High Performance long lasting heater element. •
Insulated safeguard housing. •
MSH-1818E - 18”x18” (46cm x 46cm)Simple/Easy to use.•
Low cost.•
Adjustable height. •
Energy Saver•Heatsinkreturns
70+% of heat
Premier Air/Autocycle Spot Heater ASH 1818
Autocycle Spot Heater SH 1818
Manual Spot Heater MSH-1818E
ASH-1818 - 18”x18” (46cm x 46cm)
ASH-1818, SH-1818, MSH-1818EHIX Flash/Spot Cure Models are designed for your needs; available in three models.Utilizing a rugged infra-red heating element, adjustable height and easy positioning wheels. Our SH and ASH models have an energy saving heat sink that saves 70% of your heat when in idle. Saving you big elec-tricity bills.
Model ASH 1818 18” x 18” 28 x 48 - 3000W, 14 Amps 160 .lbs, 71Kg SH 1818 18” x 18” 28 x 48 2200W, 18.5 Amps 3500W, 16.5 Amps 147 .lbs, 65Kg MSH-1818E 18” x 18” 28 x 48 2200W, 18.5 Amps 2200W, 10 Amps 120 .lbs, 54Kg
SizeHeathead
AdjustableHeight 120V 220V WT
Specs
14
36 inch wide by 12 foot long • conveyor area.Energy efficient 85,000 BTU • burner.Single speed recirculating • air system.Fresh air combustion blow-• er lowers NOx and CO emission output.Analog belt speed control • and digital temperature con-trol.High resolution gas modu-• lating valve allows tempera-ture to stay within +/-5°F of set point.
Easy access to filters for • cleaning. And removable top panels make it conve-nient for maintaining.6 foot long oven chamber • with 1 foot fume hoods on each end.Power: 220 Volt, 5 Amps / • Single Phase. Gas: 4.5”-10” water column pressure input. (Natural Gas)Recirculating Air Flow: 1/2 • HP, 1,000 CFM. Exhaust: 10” Duct, 450 CFM.Natural gas or propane • models available.
Dual recirculation blowers• Perfect for use with auto-• matic printers Energy efficient 300,000 • BTU burnerSingle speed recirculating • air system (80%-85%)Fresh air combustion blower • lowers NOx and CO emis-sion outputAnalog belt speed control • and digital temperature con-trolHigh resolution gas modu-• lating valve allows tempera-ture to stay within +/-5°F of set point
Manual reset high tempera-• ture limit switch, combustion air proving switch, recircu-lating air proving switch, exhaust air proving switch, and flame safeguard controlEasy access filters for • cleaning and removable top panels make it conve-nient for maintainingNatural gas or propane • models availableBuilt to UL-795 standard for • commercial gas fired ovens
The HIX gas Textile Dryer provides excellent cure control for plastisol, direct to garment ink jet, solvent and waterbased inks. Simply put, HIX gas dryers are the most efficient gas conveyor dryers on the market.HIX HG/BG series Gas Dryers have been designed to meet the pro-duction and energy saving goals of any modern screenprinting opera-tion. The efficient BTU burner, which works with the fresh air combus-tion blower, re-circulates most of the heated oven air to keep operation expenses low. HIX Gas dryers are capable of handling the belt cover-age and speed required to run with automated presses. Available in belt widths 36”, 48”, 60”, & 72”.
GAS DrYErS AnD ConVEYor oVEnS
Saves Energy•Better Insulation•Lowers NOx & CO •emission output.
Hg-3612 Features Include: Bg Features Include:85,000 BTU 300,000 BTU HIX Hg 3612 HIX Bg Series
Removable top panels provide
convenient access to filters for easy
maintenance.
SEE ALL OUR CONVEYOR DRYER OPTIONS AT WWW.HIXCORP.COM
COMPACT36”X12’
BUILT TO UL-795
STANDARDS
Length ............................ 12’ (365 cm)Width .............................. 45” (114 cm)Height ............................ 69” (175 cm) to exhaust/ 53” (134 cm) oventopBelt Width ...................... 36” (91 cm)Oven Length Inside ........................... 72” (182.9 cm) Outside ........................ 96” (243.8 cm)Entry Length ................. 36” (91 cm)Exit Length .................... 36” (91 cm)Belt Height (fromfloor) ... 34” (86 cm)Volt-VAC ........................120V•208-240VRecirculatingAirflow .... 1,000cfmExhaust Duct................. 10” (25 cm)Exhaust Flow ................ 450 cfmAmps.............................. 220V 3 Amps 1-Phase/ 120V 8 AmpsBTU ................................ 85,000
Length ....................20’ (610 cm) ........... 20’ (610 cm) ...........20’ (610 cm)Width ......................81” (206 cm) .......... 93” (236 cm) ..........105” (267 cm)Height ....................82” (208 cm) .......... 82” (208 cm) ..........82” (208 cm)Belt Width ..............48” (122 cm) .......... 60” (152 cm) ..........72” (183 cm)Oven Length Inside ...................132” (335 cm) ........ 132” (335 cm) ........132” (335 cm) Outside ................156” (396 cm) ........ 156” (396 cm) ........156” (396 cm)Entry Length .........48” (122 cm) .......... 48” (122 cm) ..........48” (122 cm)Exit Length ............36” (91 cm) ............ 36” (91 cm) ............36” (91 cm)
Hg-3612 Bg-4820 Bg-6020 Bg-7220See more info at www.hixcorp.com
Same for all BG DryersBelt Height(fromfloor) ...34” (86 cm)Volt-VAC ..............................208-240RecirculatingAirflow .......3,000 cfm
Exhaust Duct.................14” (36 cm)Exhaust Flow ...................1,500 cfmAmp at 220V/Phase ............... 10A/3BTU ......................................300,000
2 - 1500 CFM Blower3000 CFM Total
15SPECIALTY oVEnS For
DIrECT To GArMEnT & SuBLIMATIon
Walk in and floor models. • Convection air and infrared systems • available. Filtered air to remove dust and • impurities. Digital or analog time and temperature • controls.
Audible alarm and lights to indicate tem-• perature fluctuations. Recirculating air systems to save energy • costs. Exhaust ducts to vent fumes and mois-• ture. Mobile or stationary units. • Shelving or hanging options available.•
Since 1963, HIX has been the leader in curing water based screen printing inks on garments with our electric dryers. Our expertise with this process has put HIX years ahead of the competition, and made us the only real choice when it comes too effectively curing water based inks in an electric drying system. HIX electric dryers combine the right mix of infra red energy and forced hot convection air to evaporate water and cure ink from water based screenprint and ink jet inks. Cure direct to garment inks with our heat press, Verticure drawer or conveyor ovens.
The HIX S-650P is the most reliable Auto-Opening heat transfer machine on the market. With the added feature of a digital pressure dis-play no press can compare to the quality and consistent results of the S-650P.Features Include:
Auto-opening function: no air compressor needed.• Digital pressure, time and temp. display.• Quick release for manual opening.• Optional exchangeable platens• Floating lower platen.• Elevated arm for higher pressure.• Large opening and underside clearance for easy • shirt positioning.
S-650P HIX is proud to introduce its Verticure ovens. Designed specifically for curing Direct to Garment solvent or water based ink jet inks.Features Include:
Cures both water based and solvent based • direct to garment ink jet inks.Developed specifically for direct to garment cur-• ing applications.Perfect for shops with space restrictions the HIX • Verticure fits in a 4’x4’ footprint.Cures both light and dark colored garments in • just minutes.Separate timer for each drying drawer in either • 1, 2 or 4 drawer design.Forced hot air at each drawer level.• 208v-240v, 55 amps, 3” type B exhaust duct, • digital heat control, variable air speed control.Fiber mesh bottom in each drawer• Auto-opening drawer (• 2-drawer only)
Verticure
The NPII-3616 and NPII-3619 ovens are perfect for curing direct to garment inks and ideal for drying water-based textile inks, as well as traditional plas-tisol an solvent-based evaporative inks.Features Include:
infrared and forced air drying• 1 horsepower blower motor• side mount controls• variable belt speed• variable air speed• easy access to heater panels• double-wall insulation on top and sidewalls.•
nPII-3616
*HIX gAS DRYERS ARE ALSO A gREAT OPTION FOR CURINg DIRECT TO gARMENT PRINTS.
BATCH oVEnS Designed to suit YOUR needs. For curing products that require long process cure times and items not suitable for conveyor drying.
MUg OVENSHIX has standard and custom mug ovens:2414 Mug Oven
a 24” wide by 14’ long mug • oven system that will process over 200 mugs per hourmugs come off the oven • through our cooler, which allows for easy handling/packaging right off the production lineno messy water quenching•
RECOMMENDED FOR DIRECT TO gARMENT
PRINT FUSION
NO SCORCHES
3625 Mug Ovena 36” wide by 25’ long mug • oven system that will process 600 mugs per houra larger, longer, wider belt • allows for more wraps and higher production capabilities
Custom Mug Ovenscustom oven systems with • capacities to handle your pro-duction needs, are also avail-able - please call for more information (1-800-835-0606)
Batch Ovens Features Include:
See our HEAT PRESS CATALOg for more information on our 20+ models of presses in 120v & 220v.See our HEAT PRESS CATALOg for more information on our 20+ models of presses in 120v & 220v.
CLAMSHELLPRESSES
AUTOMATICPRESSES
SWINgAWAYPRESSES
CAPPRESSES
SPECIALTYPRESSES
HIgH VOLUMEPRESSES
Heat Transfer Presses, Screenprint and Dryers please visit:
www.hixcorp.comDough and Tortilla Presses please visit:
www.doughxpress.comCustom Built Dryers please visit:
www.ovens-dryers.comFlock Transfers please visit:
www.ez-transfers.com
HIX Corporation1201E.27thTerrace•Pittsburg,KS66762
1-800-835-0606•620-231-8568•Fax:620-231-1598E-Mail:[email protected]•Web:www.hixcorp.com
Distributed by:
©2012 HIX Corporation
March 2012
PIZZA PRESSES TORTILLA PRESSES
DOUgH DOCKINg PRESSES
FLAT gRILLS
BREAD SLICERS
DOUgH DIVIDERS/
DOUgH DIVIDER
ROUNDERSMEAT PRESSES EQUIPMENTACCESSORIES
See our FOOD CATALOg for more information on our complete line of professional food equipment.See our FOOD CATALOg for more information on our complete line of professional food equipment.
The World Leader In Heat Transfer Presses, Dryers, Screenprint Equipment, Industrial Ovens
and Food Equipment.
The World Leader In Heat Transfer Presses, Dryers, Screenprint Equipment, Industrial Ovens
and Food Equipment.