Upload
others
View
4
Download
19
Embed Size (px)
Citation preview
Highway Electrical Training Specification © HESA
Issue12.17 Page 1 of 200 © Highway Electrical Skills Academy
Highway Electrical Training Specification
for the Installation and Maintenance of
Highway Electrical Works
Meeting the requirements of
National Highways Sector Scheme 8 (NHSS 8); the Highway Electrical Registration Scheme (HERS); the Knowledge Requirements of the relevant units of CBQ-NVQ Levels 2 and 3 for the Highway Electrical
Sector
Highway Electrical Training Specification © HESA
Issue12.17 Page 2 of 200 © Highway Electrical Skills Academy
Issue Status
Issue 3 – Sept 2006 Training Course Assessment Result Banding Accreditation – amendment to include preferred assessment (closed book); additional requirements for practical assessments
Training Delivery amendments to include Lantra Awards certification and maximum numbers on courses
Requirements for Approved Trainers for delivery of 302, 310 (when developed) modified to meet requirements of NHSS 12D
Contents changed to show Lantra Awards Certification; training designed to meet the assessment requirements of NRSWA clarified
215 re-numbered as 106, pre-requisites amended accordingly
307 and 607 amalgamated – now 215
301.3-301.8 modified to align with NRSWA
302 modified to meet the requirements of SS12D as particularised by SS 8, 9B & 10 Committee
310 – marked as under development to satisfy NHSS 12D
S301.8 deleted as outside the scope of this specification
M301 and M704 course syllabi changed
Issue 4 – Feb 2007
Introduction amended to align with Issue 6 of NHSS 8, 9B and 10 Contents section revised
210/M404 – Amended to make practical assessment explicit
New Section 4 – Specialist Modules - Slot Cutting
New Section 5 – Highway Electronic – Installation of Infrastructure Equip’t
Specialist Modules Traffic Signals now Section 6
New Section 7 – Specialist Modules - Communications
New Section 8 – Specialist Modules – Variable Message Signs
New Section 9 – Specialist Modules – Env. & Monitoring Equip’t
New Section 10 – Specialist Modules - Cameras
805/M801 amended to align with CDM Regulations 2007
Issue 5 – 12 Jun 2009 Reference to NHSS 8, 9B and 10 changed to NHSS 8; Highway Electrical Industry Scheme for the Registration of Authorised Persons to Highway Electrical Registration Scheme; Training Group to Standards and Training Group; Training Specification to Highway Electrical Training Specification throughout.
Title page changed; Contents page added
Additions to exemptions for lorry loader and manual handling training
Clauses on Course Certificates, Refresher Training added; Appendix 1 detailing Refresher Training added
Various changes to the content of training specification courses
Course 101 – Environmental issues added
Course 302 split into 302.1 and 302.2 (the latter covering Temporary/Portable Traffic Signals)
Course 401 split into 401.1 (Basic) and 402.2 (Advanced)
Deletion of Authorising Officer and Qualified Supervisor courses from this Training Specification
Courses ., . - course duration amended; practical assessments included
Issue 6 – 10th Oct 2010 209-Confined Spaces training added
204.1 added for specific hand or power tool training - named
Traffic product specific codes removed, forms part of the ATO workbook
Removed previous course ref information.
Added Course maximum course number allowance
Removed 703,704, M406 and M610 course syllabus
Remove all Matrix course referencing on the syllabi
401.1,401.2,402 and 403 also available as individual courses
Highway Electrical Training Specification © HESA
Issue12.17 Page 3 of 200 © Highway Electrical Skills Academy
Issue and Date Change Issue 6 – 10th Oct 2010
Added combined course minimum durations
Course 201 Assessment required as part of the final achievement grade
Issue 7 23rd May2011
Update to the Refresher Table
G39 Awareness course added
Course 608 now included ‘name product’ to clearly identify which type is being trained
Course 602 ‘surface protection’ moved to ‘Safe Working Practices’ to incorporate all parts of the sector
Word ‘Induction’ removed from course 101 index
Page 5 additional exceptions added also includes Scaffold Training-PASMA
Change to titles for 302.1/2 page 13 to match course syllabus titles
Update to course 510 and 511 syllabus content
Added note that the HEA must be advised of TBT taking place, which could be subjected to an HEA Audit
Updated 302.1 and 302.2 combined training table – page 26
Course exceptions- further clarification of certification Abrasive wheels- NPORS and BAF (British Abrasive Federation) certificated courses added
Removed the term ‘may’ for clarification, and added further clarification to alternative sources of accepted training
Issue 8 21-Nov-2011
Working in the Vicinity of DNO equipment including G39- DNO certificated Courses with assessment. Added as an additional alternative level of certification at an appropriate level
Inclusion of the Manual Handling Passport Scheme
Update of the 210 course maximum numbers
Update to course 206.2 and 206.3 assessment
Update course duration for course 302.2 to reflect lesson plan
NEBOSH Construction Cert and/or NEBOSH Diploma accepted as an alternative to course 805 CDM
Course 205.1 assessment clarified within the syllabus
Clarification for the delivery of combination courses
Iss 8.1 24-1-2012 CDM alternative - ITB Site Management Safety Training Scheme (SMSTS)
Plant – 360 Excavator (mini Digger), Forward Tipping Dumper, Ride on Roller delivered by NPORS
Course 104 included as part of 101 to 106 combination removed from listing (other than
104) Updated to include NPORS MEWP training certification
Iss 9 May 2012 Changes to Tcam 3 to 5 durations and added 3 to 5 combination course
Replace ASLEC with HEA
EFAW included as part of the Training Specification
Updated refresher training to Training Methods
104 and 202 set to ‘full course’ for course types
Osteopaths For Industry added as an additional provider for manual handling
Included Key Objective record log
Update with Lantra Awards Logo
Course 606 duration increase to 6 hours- Combo increase by 2 hours- objectives reviewed and updated
Update to 302.1 and 302.2 to clarify the level of training
Iss 10 August 2012
301.1 to 301.8 -Added max number of Learners to 8 805 - Removed 402 and 403 from course pre-requisites Highways and Construction Training Association added to alternative provision for Manual Handling
Course 712,713,714-715-716 added-Initial and Periodic Electrical Inspection and Testing
Clarification of First Aid Training and provider status
Highway Electrical Training Specification © HESA
Issue12.17 Page 4 of 200 © Highway Electrical Skills Academy
302.3 added 712-3-4-5-6 Key objective training added Course 711 duration increase to 14hrs
Iss 11 June 2013
Course 104 title changed to Moving and Handling Course 711 214 added a prerequisite to ensure site competence can be met Course 602.5 added actual use of airless spray equipment for Manufacturers EFAW- updated change in Awarding Body qualification provision from 1st April 2013 Conversion Course explanatory note added Course 210 changed throughout to meet ENA EREC G39 issue 2 document
Iss12 Sept 2013 Addition of the Ladder Association as an alternative provision Clarification of alternative training provision Refresher Training Clarification for irregular application of skills and knowledge for a given period
Issue 12.1 July 2014 EFAW /FAW- updated change in Awarding Body qualification provision from 1st Oct 2013 EFAW Syllabus updated to align with Awarding Body requirements Update to the 204.1 plant list with specific plant type, amendment of the 204.1 course syllabus Course 205.3 Prefabricated Mobile Access and Working Towers added 302.1 course objectives updated to reflect changes in 12D requirements Manual Handling – alternative provider Lantra Awards removed St John Wales added as an alternative provider for EFAW 180 Excavator below & above 5 tonnes and 360 excavator above and below 10 Tonnes delivered and assessed by CITB for CPCS scheme Page 9 - Trainer discretion of course duration statement removed 204 course title change and syllabus content Page 30 Updated Course Combination Table and note clarification Update to Course 510 and 511 course syllabus Update to course 711 syllabus Refresher Table updated to reflect changes
Issue 12.2 January 2015
Course 215 removal of pre-requisites 301 and 302 Alternative provision – Medicot remove for moving and handling Combination course M602 and M609 added Course M602 course duration reduced to 11 hours Added corrections to include 205.3 where not required as a pre requisite Updates to Pre-requites throughout Appendix 1 –
• Change to 712,3,4,5,6 from key objectives to short course • 204 Hand held Tools including Operating Hand Held Drills/ Screwdrivers
Issue 12.3 Course 602 Syllabus amended to reflect NHSS19a changes CDM 2007 removed 2015 added Clarification on Alternative Training Provision Page 8 Abrasive Wheel Clarification Page 32 – Combination Course further clarification Page 98 404 – updated aims
Highway Electrical Training Specification © HESA
Issue12.17 Page 5 of 200 © Highway Electrical Skills Academy
Issue_12.4 Page 6 Reference to Associated documents added Page 6 Reporting of shortfalls added Page 10 Clarification on Course Durations and Learning hours Page 19 – 32 Course Hours and Learning hours added Page 11 clarification of Learner Numbers Page 35 Further clarification for the delivery of Combination Course hours Clarification of Course Learning Hours Combination Course Hours and Learning Hours updated Corrections as notified by ATO’s Highway Electrical Sector Academy is now known as the Highway Electrical Skills Academy
Issue 12.5 7th April 2016
Change to product specific titles to reflect the TRAM – certification Course 511 wordings modified to include ‘or use of a breech joint’ Refresher Training for 211 and 212 updated to read full course required
Issue 12.6 21st July 2016
Updated Alternative Training Provision – Lorry Loader (212) Updated Alternative Training Provision – Petrol Driven Cut-Off Saws including Abrasive Wheels– NPORS course -N017 Hand Held Petrol Driven Cut off Saw – Only Updated Alternative Training Provision – Petrol Driven Cut-Off Saws including Abrasive Wheels - BAF (British Abrasive Federation) removed – awaiting updated course provision Training Syllabi Contents - Refresher Training Details and Mandatory Pre-requisite requirements added Page 10 updated clarification for course Pre-requisites
Issue 12.7 30th September 2016
Updated Alternative Training Provision – 1. Course 204.1 Petrol Driven Cut-Off Saws including Abrasive Wheels–
NPORS course -N017 Hand Held Petrol Driven Cut off Saw – Certification Must clearly read - Abrasive Wheels – Hand Held Petrol Driven Cut off Saw
2. Course 403 - City & Guilds 2382-15 Level 3 Award in Requirements for
Electrical Installations
3. Course 104 - Qualsafe one-day Level 2 Award in Safe Moving and Handling
QCF added
Clarification added for The Traffic Controller Foundation Principles, M602 mandatory requirements for M698 Course Learner Changes - reduced to 8 Learners per course (effective from the 1st January 2017)
• Course 204 Hand held Tools including Operating Hand Held Drills Screwdrivers
• Course 210 Working in the vicinity of DNO / IDNO equipment including G39
Issue 12.8 20/1/17 • Alternative provision – Lorry Loader combined
• Emergency first aid at work – syllabus updated to include - apply and use correctly an automated external defibrillator (AED)
• Clarification of Qualifications (e.g. NVQ’s Levels 2/3/4/5, apprenticeships, HNC, degrees) as meeting the criteria for underpinning knowledge and refresher intervals
• Course 214 now a mandatory pre-requisite requirement. Course syllabus, assessment criteria changed for practical assessment only from 31st March 2017 – Centre re- application required.
• Course 210 requires mandatory 214 course evidence – from 31st March 2017
• Alternative provision - NPORS 204.1 NPORS Operator Card evidence – front and reverse side
• Electrical Inspection and Testing 712/713/714/715/716 alternative provision added
• Appendix 1 updated to reflect changes
Highway Electrical Training Specification © HESA
Issue12.17 Page 6 of 200 © Highway Electrical Skills Academy
Issue 12.9 23/3/2017 • Further clarification for alternative provision for MEWP
• Updated aims clarification for course 206.1 MEWP Awareness course
• Updated course title for course 706 Periodic Structural Inspection and Testing
• Appendix 1 Refresher Training Details update – special note added for 214 Full Course requirements
• Amendment to Course 210 Prerequisites syllabus for evidence of 214 course
• 302.1 and 2 Alternative Provision added
• Course 214 title update throughout
• Course 403 removed from the following course pre requisites;404,506,507,508,510,511,604,605,606, 701,702,705,708,710,M501,M502,M503,M504,M505,M506,M507,MM405,M601b, M602,M603,M604,M605,M606,M607,M608,M609,M611,TCOM004 ,TCAM002
• Clarification for alternative provision and short course e-learning.
• Clarification for M603 courses as a mandatory pre-requisite for M611 courses, except where specific conditions apply.
Issue 12.10 27072017
• Combination Course group 201/203/204/207/209 changed to reflect the minimum number of learners, based on the lowest number of possible learners.
• The term ‘All 300s’ has been removed
• Changes made to ensure harmony between the Training Specification and the Highway Electrical VRQ Specification for the Installation and Maintenance of Highway Electrical Works - issue 1.4
• Update to scope for Apprenticeship provision
• Advance notification that course 801 and course 802 titles to change to coordinate the work of others
• Refresher Training – Short Course and Key Objective Training (KOT) notification, certification and quality assurance changes.
• Chartered Institute of Environmental Health-(CIEH) removed from alternative provision for moving and handling course 104
Issue 12.11 09012018
• Update to Combination course notes - Where a combination course comprises of a mixture of full, short or KOT training, the full combination course must be completed
• Course 708 and 709 reviews, course 709 noted as specialist Course Training
• Course 708 syllabus updated to include Overview of High Mast installation
• Course 801 and course 802 titles to change to coordinate the work of others
• Update to using Combination courses and short courses in terms of Learner numbers and course durations – Read Note following Course Combination Course Durations table
• M301 clarification added for mandatory requirement
• Page re-numbered throughout
Issue 12.12 07032018
• Level 2 Award in Safe Moving and Handling (RFQ) included • Course 711 removed throughout
Issue 12.13 27112018
• Further clarification to note for course 214 in Appendix 1, where the operatives’ 210 certificate has expired, the course 214 in date certificate will be required before attending the next 210 course, if time expired, 214 course will be required
• Alternative Training for BS 7671 - IET Wiring Regulations (403) – EAL Requirements For Electrical Installations BS7671: June 2008 (2015) – course code 601/5321/0
• Corrected combination for M501/503/504/505 for traffic control systems
Highway Electrical Training Specification © HESA
Issue12.17 Page 7 of 200 © Highway Electrical Skills Academy
• Course 403 course duration increased to 14 hours with learning hours of 12, course title has been updated to reflect the current regulations to aid auditing and currency of operative knowledge – BS 7671:2018 - IET Wiring Regulations
• Combination course 401.1, 402 and 403 hours updated
• Highway Electrical Apprenticeship recognition added for underpinning training and associated qualifications
• Updated list for alternative training provision • 212/211 - Lantra Slinger/signaller • 204.1 - Hand Held Disc cutter • 403 -BS7671 - Scottish Electrical Charitable Training Trust (SECTT)
Apprenticeship,
• Course 717 Fundamental Inspection and Testing for the Addition or Alteration to an Installation added (course 711 replacement)
• Update to combination courses and KOT
Issue 12.14 07052019
• Update to Training General Requirements
• Appendix 1 updated
• Course 210 special note added to cover consecutive training and prohibited split course delivery
• Page number reordering
Issue 12.15 08012020
• Changes to course 717 course objectives
• Clarification on HESA pre-requisite courses and the use of Alternative Provision and E-Learning
• Specification of course certificate validity
• Course 705 learning hours updated
Issue 12.16 27th July 2020
• Update to reflect 602 course 602a Fettler and 602.5 to meet the requirements of NHSS 19a
• Updated 204.1 Hand Powered Tools - Petrol Driven/ to read Hand Powered Tools - Petrol Driven/Cordless Cut-Off Saws and Abrasive Wheels
• Updated to NPORS alternative Training now reads - N017 Abrasive Wheels - Hand Held Cut Off Saw
• Lantra Awards Certificate Handheld Engine Driven Disc Cutter removed from 204.1 list of accepted alternative provision
• Course certification validity period clarified for expiry
• 301.2 Minor excavation and temporary reinstatement in the highway for column holes - learning hours added
• 206.2 MEWP Operators Course (Boom Type) removed
• 206.3 MEWP Operators Course (Scissor Lift) removed
• 206.2 and 206.3 Safe Working Practices - MEWP Operator Reference to Alternative HERS accepted training and assessment.
• Course M405 aims Using Test Equipment on Non-Energised Circuits to BS 7671 updated to reflect current regulations
• Page number updated throughout.
Issue 2.17 12th Aug 2020
• Following recognition from the UK contractors Group (UKCG) for the National Plant Operators Registration Scheme (NPORS) during September 2014 specific reference to CPCS registration has been removed from course 212-Use of Lorry Mounted Crane in the installation of structures supporting highway electrical equipment
Highway Electrical Training Specification © HESA
Issue12.17 Page 8 of 200 © Highway Electrical Skills Academy
This Page is left intentionally blank
Highway Electrical Training Specification © HESA
Issue12.17 Page 9 of 200 © Highway Electrical Skills Academy
Contents Page No.
Scope and Exemptions 9 Training Course Assessment Result Banding 12
Course Durations Training Delivery
12 14
Course Certificates 14 Training General Requirements 15
Refresher Training 15
Acknowledgements 15 Training Syllabi Contents Section 1 Common Modules Section 2 Specialist Modules - Public Lighting and Illuminated Signs Section 3 Specialist Modules - Traffic Signs (non-Electrical) Section 4 Specialist Modules – Slot Cutting Section 5 Specialist Modules – Highway electronic Installation of Infrastructure Equipment Section 6 Specialist Modules – Traffic Signals Section 7 Specialist Modules - Communication Section 8 Specialist Modules – Variable Message Signs Section 9 Specialist Modules – Environmental and Monitoring Equipment Section 10 Specialist Modules - Cameras
16 40 86 117 125 130 134 166 173 177 181
Appendix 1 – Refresher Training Details 192
Associated Documents This document (for Approved Training Organisations) must be read in conjunction with the current issue of the Requirements for Approved Training Organisations and Approved Trainers Notification of Errors Whilst every effort is taken to ensure this document is error free, should, in the unlikely event an error has been identified, please report this to the HESA at [email protected]
Highway Electrical Training Specification © HESA
Issue12.17 Page 10 of 200 © Highway Electrical Skills Academy
Training Courses for Highway Electrical Works
Scope The NHSS 8 Standards and Training Group have established and identified a number of courses which together with the HESA requirements for Approved Trainers, will ensure the level of training within the Highway Electrical sector meets a minimum requirement of professional learning. The minimum level will provide evidence of underpinning knowledge for the Highway Electrical Registration Scheme (HERS) and will support the CBQ level 2 and 3 knowledge outcomes. This document should be read in conjunction with the Highway Electrical Registration Scheme Handbook and the Requirements for Approved Training Organisations and Approved Trainers, available from the HESA web-site at www.thehea.org.uk. HESA Approved Providers that are also approved to deliver the Highway Electrical Apprenticeships are required to read this document in conjunction with the current Highway Electrical VRQ Specification for the Installation and Maintenance of Highway Electrical Works
It should be noted that any training not carried out in accordance with the Highway Electrical Training Specification by HESA Approved Trainers and appropriately certificated (by Lantra Awards in partnership with the HESA or by the Highway Electrical Skills Academy alone) or not specifically identified within the Highway Electrical Training Specification as agreed alternative training provision will be deemed as not meeting the knowledge requirements of this Sector Scheme and the associated Highway Electrical Registration Scheme.
Alternative Training Provision
Where alternative training provision has been adopted to replace HESA training courses, this does not preclude the completion of the required pre-requisite training for the related HESA course or courses.
On-line E-training is not accepted as a substitute for Highway Electrical Training Specification Courses, except where specifically stated.
(NOTE: For Alternative Training Provision, this must be certificated by the Awarding Body/Association in which the centre is regulated by and meet the certification validity as specified below. Short course e-learning is not permitted in all cases, unless specifically stated
➢ First Aid at Work or Emergency First Aid at Work Training – certificated by
St. John’s Ambulance, St. Andrew’s, St John Wales Red Cross, Lantra Awards & other Ofqual - Approved First Aid at work training providers. As of 1 October 2013,
the Health and Safety (First Aid) Regulations 1981 have been amended, removing the requirement for HSE to approve first aid training providers / delivery and qualifications. The change is part of HSE's work to reduce the burden on businesses and put common sense back into health and safety, whilst maintaining standards. The changes relating to first aid apply to businesses of all sizes and from all sectors. HSE will continue to set the standards for training. While the changes give employers flexibility, the one-day Emergency First Aid at Work (EFAW) and three day First Aid at Work (FAW) courses remain the building blocks for first aid training. The First Aid at Work ACoP has been amended accordingly with the HSE setting out the training and delivery requirements and signposting further guidance. There is a clear hierarchy with Awarding Organisations (such as Lantra Awards) regulated by Ofqual and the Voluntary Aid Societies (St John Ambulance, British Red Cross and St Andrew’s First Aid) providing assurance to the employer that training and assessment will be delivered to the standards required and monitored (internally verified) to ensure consistency in the quality of the training and assessment delivery
➢ MEWP Training and Assessment– certificated by Lantra Awards, IPAF registered
training providers, NPORS registered training providers, Equipment Operators Registration Scheme (EORS) approved
➢ Lorry Mounted Crane Operator (212) and Banksman Slinger/Signaller (211) –certificated by CPCS, ALLMI, NPORS, RTITB, Equipment Operators Registration Scheme (EORS) approved, Lantra certificate to state for Lorry Mounted Crane –
Highway Electrical Training Specification © HESA
Issue12.17 Page 11 of 200 © Highway Electrical Skills Academy
Slinger/Signaller (organisations must discuss with provider the requirement for column lifting assessment to meet the HERS criteria)
➢ Lorry Mounted Crane Operator (212) only – City & Guilds CITB 36a, SQA Plant Operations L2 DY5F
➢ Plant – 360 Excavator (mini Digger), Forward Tipping Dumper, Ride on Roller certificated by NPORS
180 Excavator below & above 5 tonnes and 360 excavators above and below 10 Tonnes certificated and assessed by CITB for CPCS scheme
➢ Moving and Handling (104) - (does not include E-Learning) certificated by The
British Safety Council, City and Guilds, Institution of Occupational Safety and Health-(IOSH), British Red Cross, The Royal Society for the Prevention of Accidents- (RoSPA), St. John’s, National Plant Operators Registration Scheme (NPORS), Osteopaths For Industry-Health Response UK. Qualsafe one day Level 2 Award in Safe Moving and Handling QCF/RQF. HCTA - Highways and Construction Training Association All trainers delivering this course must have been trained directly by the one of the organisations listed here and learners must be certificated directly by the same organisation. Trainers that fall within the required scope and hold documented evidence demonstrating appropriate occupational competence can deliver training to the requirements as detailed within the HERS Training Specification. The level of training must comply with the HERS Training Specification course number 104 for maximum number of learners, formative and summative assessment criteria. Each Learner must receive a certificate of achievement that is issued by the organisation listed here only. Or Training that has been provided under the All Wales Manual Handling Training Passport and Information Scheme and there is evidence of planning and recording of such training as specified within the supporting documentation for the passport scheme with clearly defined certification that reflects the required passport scheme records.
➢ Petrol Driven Cut-Off Saws including Abrasive Wheels 204.1 - (Training and assessment in the use of Petrol Driven Cut-Off Saws will be required in addition to Found04 for those employees operating this equipment) certificated by, NPORS Course N017 Abrasive Wheels - Hand Held Cut Off Saw- certificate (and/or NPORS Operator Card evidence – front and reverse side) to state Abrasive Wheels – Hand Held Cut Off Saw.
➢ Steps and Ladders (205.1) - certificated by NPORS, The Ladder Association
➢ BS 7671 - IET Wiring Regulations (403) - City & Guilds 2382-15 Level 3 Award in Requirements for Electrical Installations, City & Guilds 2382-18 Level 3 Award in Requirements for Electrical Installations. Scottish Electrical Charitable Training Trust (SECTT) Apprenticeship
➢ Scaffold Training- certificated by PASMA
➢ Working in the Vicinity of DNO equipment including G39 (210) - DNO certificated Courses with assessment at an appropriate level,
➢ CDM 2015 (805) - The following are permitted as alternatives to the course 805 CDM Training: -The NEBOSH Construction Certificate and NEBOSH Diploma, The CITB Site Management Safety Training Scheme (SMSTS)
➢ Electrical Inspection and Testing 712/713/714/715/716 – City and Guilds 2391 plus 2381-15, or City and Guilds 2391 plus 403 (latest) both requiring Traffic Signals, Public Lighting, Motorway Communications and/or VMS system understanding for electrical testing. City and Guilds 2394 (initial) plus 2395 for
Highway Electrical Training Specification © HESA
Issue12.17 Page 12 of 200 © Highway Electrical Skills Academy
periodic only. Scottish Electrical Charitable Training Trust (SECTT) Apprenticeship
➢ Installing, maintaining and removing temporary traffic management on rural and urban roads 302.1 and Installing, maintaining and removing positive traffic control including temporary / portable traffic signal equipment on rural and urban roads 302.2 - relevant in date NHSS 12D training, assessment and NHSS 12D card
➢ 709 Install high mast lighting – Specialist works, dispensation applied for manufacturing training only. This level of specialist Training is required to endorse the key elements of underpinning learning and must not disadvantage or exclude Learners. The Pre-requisite Underpinning knowledge criteria applies.
Validity of alternative training provision certification shall be a maximum of 5 years from the date of the training (less than the 5 year period if the alternative provision deems this period to be less).
Qualifications (e.g. NVQ’s, apprenticeships, HNC, degrees) do not need to be repeated and do not fall within this requirement, except where there are training elements as part of the qualification which fall within this Training Specification and the requirements of NHSS8 / HERS
For Refresher Training - alternative provision falls within the Appendix 1 Refresher Training Details, criteria, except where the alternative provision training requires a higher level of recertification.
Refresher Training applies equally to all categories of HERS registered operatives (including those registered under the Industry Accreditation Route) as applicable to their scope of registration, as defined by the level of registration under the Skilled Persons Route
Lantra Awards endorse the Highway Electrical Industry Training Specification courses, developed under the auspices of Sector Scheme 8 and the associated Highway Electrical Registration Scheme and acknowledge this through their technical awards.
The Training Specification developed by the Highway Electrical Skills Academy in partnership with Lantra Awards is mandatory for SSD8 and the associated Highway Electrical Registration Scheme. Training delivered in accordance with or exempted within the Training Specification is viewed by Lantra Awards as demonstrating best practice in providing under-pinning knowledge for the CBQ.
The Training Specification has been developed by the industry for the industry and the courses within have all been mapped against the relevant National Occupational Standards (NOS). Assessors can therefore be assured that the training devised within the Training Specification meets the required standard against the NOS.
Highway Electrical Trailblazer Apprenticeship Standards Achievement of either or both levels of the apprenticeship will have met in full the required level of underpinning knowledge and associated level of NVQ/CBQ as specified within this document and therefore satisfies the requirements of the Highway Electrical Registration Scheme
• Highway Electrical Maintenance & Installation Operative Level 2
• Highway Electrician / Service Operative Apprenticeship, Level 3 (includes Upskilling) To meet internal and external audit requirements, evidence for date of individual course achievement will be required and added to the Learners HERS e-portfolio for reference. Achievement dates should be added to the Learners Ongoing development Training plan to ensure key dates for repeat/update training is not allowed to lapse.
Highway Electrical Training Specification © HESA
Issue12.17 Page 13 of 200 © Highway Electrical Skills Academy
Training Courses and Syllabi There are a number of competency matrices shown in the Highway Electrical Registration Scheme Handbook. These cover a number of specific sectors within the Highway Electrical sector. These define areas of competency assessment required for different occupational tasks. Course syllabi have been prepared as shown in Sections 1, 2, 3 and 4. These courses not only support the needs of the sector competence card scheme but also support the required needs of the CBQ outcomes. The pre-requisites for each course are shown in the Contents Section, the identified pre-requisites are courses or a specific course requirement(s) that is/are required prior to taking follow-on course. Course pre-requisites, in general terms ensure that the Learner is not disadvantaged due to limited knowledge or experience before progression on to the next stage of training. Pre-requisite may be shown through certificated training, or from experience (experiential Learning) as confirmed by the employer. In certain circumstances confirmation of having attended an accepted certificated training course must be obtained (in addition to a possible statement confirming the required pre-requisite underpinning knowledge). The courses have been defined by a set syllabus, which provides the minimum level of required outcomes from the training. It will be the responsibility of the Approved Trainer to ensure that the training meets the outcomes of the training syllabus. Full details on the process for the approval and registration of Approved Trainers and Approved Training Organisations are available from the Highway Electrical Skills Academy –www.thehea.org.uk
Training Course Assessment Result Banding Accreditation The requirements for the end of course assessments are set out below:
• For multi-choice, closed book assessments (this is the preferred assessment as agreed by the SS 8 Standards and Training Group):
• Below 70% referred
• Equal to or Over 70% constitutes a Pass
• For multi-choice, open book assessments:
• Below 75% referred
• Equal to or Over 75% constitutes a Pass
• For assessments other than multi-choice, closed or open book assessments:
• Below 65% referred
• Equal to or Over 65% constitutes a Pass Those areas in which health and safety are critical - particularly for practical assessments – should be identified and the Learner must pass each of these. This would need taking into account when compiling the final mark. It is the responsibility of the Approved Trainer to ensure that the marking of practical assessments is recorded, transparent and available for audit.
Course Durations The course durations specified are the recommended minimum learning times only. Within the recommended time frame to complete the course, it is expected that the application of professional training would have ensured that the required level of learning had taken place and that multi-choice summary evaluations and practical assessments to determine the required level of understanding have also taken place. Approved Training Organisations (ATO) are expected to ensure that they meet the learning hours required for any course or permitted combination of courses. Whilst the HESA may carry out ‘ad hoc’ checks, ATO's should not rely on this as a means of compliance checking
Highway Electrical Training Specification © HESA
Issue12.17 Page 14 of 200 © Highway Electrical Skills Academy
A course can be longer than the recommended time frame, which would also take into account special needs and the abilities of the learner group. This must not exceed the specific learning daily hours specified below To ensure maximum learner engagement, concentration, focus and Learner recovery, training delivery is required to be delivered in ‘bitesize’ sessions, where;
▪ A course of duration of 4 hours is required to have typically a 15-minute break period,
which can be either one break or a number or shorter breaks. A course of length shorter
than 4 hours is required to have suitable breaks proportionate to the length of the course
▪ A course of 7 hours (one day), or a combination of days is required to have typically as a
minimum two 15 minute breaks which can be either one break or a number of shorter
breaks and one 30 minute lunch break, resulting in a minimum of 6 hour learning period,
split into reasonable blocks.
▪ A learner should not be subjected to more than 7.5 hours learning in any one working day,
either by single course multiples or by a combination of courses, and subject to point 4
being met and documented.
▪ Where a provider intends to deliver a number of courses within the same day to the same
learning cohort, clear evidence is required to demonstrate that the Learner welfare and
learning taxonomy have been considered and suitably catered for to ensure maximum
learner engagement.
▪ A course that specifically contains a large proportion of Learner practical activity and
learner ‘Hands On’, may constitute a break period for learners due to waiting time, this
must be reflected within the Trainer Lesson plan outcome report to clarify
▪ Course durations and effective learning hours specified are based on the maximum
number of Learners, where the number of learners are less than the maximum number of
Learners, course completion may vary. Such variations should be reflected on the Trainer
lesson plan comments for audit purposes.
Learning Hours - is the number of hours of learning within the Total Course duration hours which
include the appropriate level of breaks as clarified in 1 to 6 above.
Learner Numbers The term ‘Maximum Learner Number’ relates to the maximum number of learners allowed on a course, for any training period per trainer.
Competency Matrix and Occupations A Competency Matrix has been developed for a number of Highway Electrical sectors. These identify areas for the assessment of competency against occupational titles and the delivery of underpinning knowledge. They can be found in the Highway Electrical Registration Scheme Handbook. The matrices indicate mandatory items, which must be satisfied; if the employee carries out additional matrix tasks these items then become mandatory, there are also forbidden items which are not available to certain occupational titles. The Competency Matrix is used by HEA, as administrator of the scheme, to determine the general mandatory areas of competency for checking portfolios on application for registration. Mandatory items are designated by an “M” in the relevant box. An “M” in the Competency Matrix under a given occupation indicates that one or more of the individual elements which make up the
Highway Electrical Training Specification © HESA
Issue12.17 Page 15 of 200 © Highway Electrical Skills Academy
underpinning knowledge requirements of that area of competency will be required to be assessed (in terms of application of that knowledge) on site. An “X” in the Competency Matrix indicates that this area will not be expected to be present by HEA, as the Scheme Administrator, nor will this area be assessed for evidence of competency through the third-party audit. However, this does not preclude individual development and on-going training to increase or widen under-pinning knowledge.
Training Delivery Training will be delivered by Approved Trainers and Approved Training Organisations who meet the requirements and standards set by the Highway Electrical Skills Academy in partnership with Lantra Awards. It is their responsibility to ensure that effective training to common standards is achieved throughout the industry and that there is no abuse of the minimum recommendations. It is the responsibility of the Approved Trainers and Approved Training Organisations to ensure the requirements of the Approved Training Organisations manual are applied at all times, including learning room and onsite risk assessments. HESA will certificate the courses against the specified syllabi shown in the Contents section. A fee is due for each certificate. Specifically for Course 302.1 and 302.2 (& Course 310 when developed), it is necessary not only to meet the standard HESA / Lantra Awards requirements for Approved Trainers, but also to meet the additional Lantra Awards requirements for Approved Trainers for this course, as derived from NHSS 12D. The Standards and Training Group has agreed a maximum number of 8 learners per Approved Trainer for practical based courses and 12 per Approved Trainer for knowledge-based courses. The course index identifies the maximum number of Learners per course, as defined by the Training and Standards Group.
Course Certificates Approved Training Providers must apply through the HESA for course certificates including Key Update Training unless these are stated as exempted herein. All certificates must be applied for within the given timeframe, preferably, as soon as practicable after completion of the course to minimise the delay for certification processing. Where specific product or sector extensions are required for the courses, the appropriate section for workbook Form 6 must be correctly set to ensure appropriate certification All HESA course certifications are valid for 5 years from the date of achievement, except for the following exceptions;
• Emergency First aid at Work – 3 years
• HERS Qualified Supervisor Training (all settings) – 3 Years
• HERS Authorisation Officer Training (all settings) – 3 Years
Highway Electrical Training Specification © HESA
Issue12.17 Page 16 of 200 © Highway Electrical Skills Academy
Training General Requirements NHSS 8 and the Highway Electrical Registration Scheme (HERS) require training at intervals not greater than every five years. This is a maximum period and employers should make a judgement as to whether the periods between training should be reduced. In order to assist registered organisations, the HEA Technical and Training Committee acting in its capacity as the NHSS 8 Standards and Training Group has produced recommendations for training for each Highway Electrical Training Specification module, as set out in the following table. The recommendations should be read in conjunction with this document and should be taken as the minima to be applied. The requirements can be enhanced depending on specific and particular circumstances.
Refresher Training The requirements as set out in appendix 1 of this document, assume that the person who gained a Lantra certificate, HESA, or from a named alternative provider, from the original course has been practising the application of the knowledge requirements on a regular basis within the last year of validity of the certificate. If this is not the case, then the employee should have to undertake the full course again. Appendix 1 does not remove the responsibility of the organisation to ensure the employees have been appropriately trained in line with the specification and to meet the requirements of the Highway Electrical Registration Scheme Where specified within Appendix 1, full course training requirements must be undertaken before the current certification expires Training is categorised as:
• Full Course This course is delivered in accordance with Training Specification and Approved Training Organisation Requirements by Highway Electrical Skills Academy (HESA) Approved Trainers or exempted training organisations as defined in the Highway Electrical Training Specification.
Further detail can be found in Appendix 1 of this specification.
E-Learning Where organisations wish to use an E-learning approach, the HESA must be advised in writing of the propose strategy and working procedure for this method Acknowledgements The Standards and Training Group is grateful for the time and effort contributed by trade organisations, employers, Institutions and individuals in the preparation, review and ongoing development of this Highway Electrical Training Specification. Further information can be obtained from: Principal Highway Electrical Skills Academy
Highdown House, Littlehampton Road, Ferring West Sussex BN12 6PG
Tel: 01903 705140
Highway Electrical Training Specification © HESA
Issue12.17 Page 17 of 200 © Highway Electrical Skills Academy
Training Syllabi Contents: Section1 - Common Modules for Highway Electrical Works
Certification
Course Title Pre-requisite
Underpinning knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Rec. Hrs
Learning Hours
Maximum Learner Number
Available individually
Emergency First Aid At Work None 41 7 6 12
HESA Certificated Course: - Health and Safety
Certification Course Ref No
Title Pre-requisite
Underpinning knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Rec. Hrs
Learning Hours
Maximum Learner Number
HESA
Certification for all the courses in this table in
total and individually1
1011 Health, Safety and Environment at
Work None
42 4 3.75 12
1021 Control of substances hazardous
to health None
43 4 3.75 12
1031 Electrical Safety None 44 4 3.75 12
1041 Moving and Handling Highways
Electrical None
45 3 3 12
1051 Interpretation of Legislation &
Standards 101
46 4 3.75 12
1061 Emergency Preparedness All 100’s 47 2 2 12
Highway Electrical Training Specification © HESA
Issue12.17 Page 18 of 200 © Highway Electrical Skills Academy
HESA Certificated Course: - Essential Safe Working Practices
Certification Course Ref No
Title Pre-requisite
Underpinning knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Rec. Hrs
Learning Hours
Maximum Learner Number
HESA Certification
for all the courses in this table in
total and individually1
2011 Hazards and Risk Assessment All 100’s; 48 4 3.75 12
203*1 Appreciation of Public Lighting and
T/Sign Equipment None
49 4
3.75 12
2041
Hand held Tools including Operating Hand Held Drills/ Screwdrivers
All 100’s; 201,207
50 4
3.75
8
2071 Effective Personal Protective
Equipment All 100’s; 201
51 4
3.75 12
2091 On Site Safety All 100’s; 201 52 7 6 12
*Note: Course 203 above should be substituted by one or more of the following as appropriate for the work type covered:
Certification Course Ref No
Title Pre-requisite
Underpinning knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Rec. Hrs
Learning Hours
Maximum Learner Number
S203*
1
Appreciation of Traffic Sign Products & associated legislation
and guidance
None
53 14
12 12
M203*1 Traffic Product Appreciation None 55 4 3.75 12
Highway Electrical Training Specification © HESA
Issue12.17 Page 19 of 200 © Highway Electrical Skills Academy
HESA Individually Certificated Courses: - Safe Working Practices
*Note: Course 210 must be delivered in one single day. Where consecutive training is taking place, the centre must have in place a process to cover Pre-requisite requirements (excluding Combination Courses)
Certification Course Ref No
Title Pre-requisite
Underpinning knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course. Hrs
Learning Hours
Maximum Learner Number
Available individually 202
Avoiding Danger from Underground Services (training
designed to meet the assessment requirements of NRSWA Unit 1)
All 100’s; 201,207,209
55 7
6 8
Available individually1
205.11 Work at height with steps and
ladders All 100’s; 201
57 4 3.75 8
Available individually
205.2 Work at height with Scaffold
Towers All 100’s; 201
58 2 2 8
Available individually
205.3 Prefabricated Mobile Access and
Working Towers All 100’s; 201
59 4 3.75 8
Available individually
206.1 Mobile Elevating Work Platform
awareness All 100’s; 201
58 4 3.75 12
None 206.2 206.3 MEWP Operators Refer to Alternative Training provision for HERS accepted Training and assessment
Available individually1
2081 Loading, Transporting and Removing Goods (Vehicular)
All 100’s; 201, 207
61 4 3.75 8
Available individually
210* Working in the vicinity of DNO / IDNO equipment including G39
All 100’s; 201; 214
62 7 6 8
Available individually
210.1 Work in the Vicinity of DNO / IDNO Equipment Awareness (Incl. G39)
All 100’s; 201;
63 5 4.30 12
Available individually
214 Safe Isolation All 100’s; 201
66 4 3.75 8
Available individually
215 Emergency Attendance All 100’s; 201, 207,209;
65 4 3.75 12
Available individually 602
Brush Painter – Apply Surface Protection
All 100’s; All 200’s except 202, 205.2,
206.1, 211, 212
66 14 12 8
Available individually 602a Fettler
All 100’s; All 200’s except 202, 205.2,
206.1, 211, 212
67 7 6 8
Available 602.5 Spray Painter 68 21 18 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 20 of 200 © Highway Electrical Skills Academy
Certification Course Ref No
Title Pre-requisite
Underpinning knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs
Learning Hours
Maximum Learner Number
The course duration below may vary by up to 20%, depending on the number of learners and the amount of available plant equipment during the practical and assessment periods.
204.1 Hand Powered Tools (Specific Named Product Group)
Certification
204.1 Petrol Driven/Cordless Cut-Off Saws and Abrasive Wheels
All 100’s,201, 202, 207
56 7 6 8
204.1 Road Side Breaker - Pneumatic Lorry Mount, Hydraulic, Electric 230/110, Petrol One Piece
All 100’s,201, 202, 207
56 7 6 8
204.1 Vibrating Plate - Flat Plate All 100’s,201,207 56 5 4 8
204.1 Vibrating Plate - Trench Rammer All 100’s,201,207 56 5 4 8
204.1 Vibrating Plate - Single/Double Vibrating Roller Drum
All 100’s,201,207
56 5 4 8
204.1 Vibrating Plate - Flat Plate, Trench Rammer, Single/Double Vibrating Roller Drum
All 100’s,201,207
56 7 6 4
204.1 Powered Saw -Reciprocating Saw All 100’s,201,207 56 5 4 8
Individually Certificated Courses: - Chapter 8 and training designed to meet the assessment requirements of the NRSWA
Certification Course Ref No
Title Pre-requisite
Underpinning knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs
Learning Hours
Maximum Learner Number
Available individually
301.1 Excavate (training designed to meet the
assessment requirements of NRSWA Unit 3) All 100’s; 201,202
207,209
69 -
8
Available individually 301.2
Minor excavation and temporary reinstatement in the highway for column
holes.
All 100’s; 201,202 207,209
70 4 3.75 8
Available individually 301.3
Reinstatement and compaction (training designed to meet the assessment
requirements of NRSWA Unit 4) All 100’s; 201, 207,209
69
-
8
Available individually 301.4
Reinstatement of sub-base and base (leading to assessment to NRSWA
Unit 5)
All 100’s; 201, 207,209; 301.3
-
8
Available 301.5 Reinstatement of cold lay bit-mat All 100’s; 201, 207,209; - 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 21 of 200 © Highway Electrical Skills Academy
individually (training designed to meet the assessment requirements of NRSWA Unit 6)
301.3
Available individually 301.6
Reinstatement of hot lay bit-mat (training designed to meet the assessment
requirements of NRSWA Unit 7)
All 100’s; 201, 207,209; 301.3
-
8
Available individually 301.7
Reinstatement of concrete slabs (training designed to meet the assessment
requirements of NRSWA Unit 8)
All 100’s; 201, 207,209; 301.3
-
-8
Available individually 301.8
Reinstatement of modular and concrete (training designed to meet the
assessment requirements of NRSWA Unit 9)
All 100’s; 201, 207,209; 301.3
-
-
Available individually & combined with 302.2
302.1 Installing, maintaining and removing
temporary traffic management on rural and urban roads
All 100’s; 201, 207,209
71 7 6 8
Available individually & combined with 302.1
302.2
Installing, maintaining and removing positive traffic control including temporary / portable traffic signal equipment on rural and urban roads
All 100’s; 201, 207,209; 302.1
72 7 6 8
Available individually 302.3
Installing, maintaining and removing temporary traffic management on dual carriageways restricted to 40 mph or less
All 100’s; 201, 207,209
77 7 6 8
Available individually
310
Monitoring Signing, Lighting & Guarding (training designed to meet the
assessment requirements of NRWSA Unit 10)
All 100’s; 201, 207,209
74 7 6 -
Available individually 311
Monitoring Excavation in the Highway (training designed to meet the assessment
requirements of NRWSA Unit 11) All 100’s; 201, 207,209
75
-
-
Available individually 312
Monitoring Reinstatement and Compaction of Backfill Materials (training designed to
meet the assessment requirements of NRWSA Unit 12)
All 100’s; 201, 207,209
-
-
Available individually 313
Monitoring Reinstatement of sub-base and top layer materials(training designed to meet
the assessment requirements of NRWSA Unit 13)
All 100’s; 201, 207,209
-
-
Available individually
314 M314
Monitoring reinstatement in bituminous material (training designed to meet the assessment requirements of NRWSA Unit 14)
All 100’s; 201, 207,209
-
-
Available 315 / Monitoring reinstatement in concrete All 100’s; 201, 207,209 - -
Highway Electrical Training Specification © HESA
Issue12.17 Page 22 of 200 © Highway Electrical Skills Academy
Certificated Courses: -Electrical Theory, Practice and Initial and Periodic Electrical Inspection and Testing (N/A for Associated Highway Works)
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply)
Page Course
Hrs
Learning Hours
Maximum Learner Number
HESA Certification for
all the courses in this table in total
only and individually
401.1 Basic Electrical Theory All 100’s; 201 76 14 12 12
402 Electricity at Work Regulations All 100’s; 201 77 4 3.75 12
403 BS7671:2018 / IET Wiring
Regs All 100’s; 201, 402
78 14 12 12
Available individually
401.2 Advanced Electrical Theory All 100’s; 201; 401.1
79 14 12 12
Available individually 712
Initial and Periodic Electrical Inspection and Testing (Public Lighting and Traffic Control)
All 100’s; All 200’s except 202,204.1 205.2, 211, 212; (214, 401), 402, 404; 604
403 80 28 24 8
Available individually 715
Initial and Periodic Electrical Inspection and Testing (Communications Traffic Control)
All 100’s; All 200’s except (202,204.1 205.2, 211, 212;
214) 401, 402, 404;
403 81 28 24 8
Available individually 717
Fundamental Inspection and Testing for the Addition or Alteration to an Installation
All 100’s; All 200’s except (202,204.1 205.2, 211, 212;
214) 401, 402, 404;
403 114 21 18 8
individually M315 slabs(training designed to meet the assessment requirements of NRWSA Unit 15)
Available individually
316 / M316
Monitoring reinstatement in modular and concrete surfaces(training designed to meet the assessment requirements of NRWSA Unit 16)
All 100’s; 201, 207,209
-
-
Highway Electrical Training Specification © HESA
Issue12.17 Page 23 of 200 © Highway Electrical Skills Academy
Certificated Courses: - Management and Supervision
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply)
Page Course
Rec. Hrs
Learning Hours
Maximum Learner Number
HESA Certification
for all the courses in this table in
total and individually
801 Coordinate the work of others
on site All 100’s; All 200’s except
202 & 211 & 212
82 7 6 12
802 Set teams to work &
Coordinate the work for Quality, Safety & Productivity
All 100’s; All 200’s except 202 & 211 & 212
801
83 14 12 12
805 CDM Awareness All 100’s; 201; 84 7 6 12
Highway Electrical Training Specification © HESA
Issue12.17 Page 24 of 200 © Highway Electrical Skills Academy
Section 2 Specialist Course Modules - Public Lighting & Illuminated Signs Certificated Specialist Courses: - Public Lighting - Installation Techniques
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Rec. Hrs
Learning Hours
Maximum Learner Number
Available individually &
combined
211 Lorry mounted crane – Slinger /
Signaller All 100’s; 201, 207
86 7 6 8
212 Lorry mounted crane – Operator All 100’s; 201, 207 87 7 6 8
Certification for all the courses in this table in
total and individually
501 Erect Columns and Brackets All 100’s; 201, 202, 203, 204, 207, 208, 209, 210,
211, 212; 302
88 3 3 8
502 Remove columns and brackets All 100’s; 201, 202, 203, 204, 207, 208, 209, 210, 211, 212, 214; All 300’s
89 2 2 8
503 Re-align columns and brackets All 100’s; 201, 202, 203, 204, 207, 208, 209, 210,
211, 212; All 300’s
90 1 1 8
504 Install feeder pillars All 100’s; 201, 202, 203, 204, 207, 208, 209, 210;
91 1 1 8
Certification for all the courses in this table in
total and individually
505 Install Base lit bollard base All 100’s; 201, 202, 203, 204, 207, 208, 209, 210;
92 4 3.75 8
508 Installation of base-lit bollard All 100’s; 201, 203, 204,
207, 208, 209, 210, 214; All 402,
93 4 3.75 8
Certification for all the courses in this table in
total and individually
506 Installation of lantern and
bracket
All 100’s; 201, 203, 204, 205.1, 206.2/3, 207, 208, 209, 210, 214; All 300’s;
402,
94 3 3 8
507 Installation of wiring and control
gear
All 100’s; 201, 203, 204, 207, 208, 209, 210, 214; All
402,
95 4 3.75 8
Available individually 509 Install underground cables
All 100’s; 201, 203, 204, 207, 208, 209, 210, 214; All
300’s
96 7 6 8
Certification for all the
510 Terminate and connect U/G
cable into cut out All 100’s; 201, 203, 204,
207, 208, 209, 210, 214; All
97 3 3 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 25 of 200 © Highway Electrical Skills Academy
Certificated Specialist Courses: - Public Lighting - Maintenance Techniques
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Rec. Hrs
Learning Hours
Maximum Learner Number
Available individually
601 Night time monitoring All 100’s; 201,203, 207
99 4 3.75 12
Available individually
608 Operate raising and lowering columns (named – equipment
specific)
All 100’s; All 200’s except 202, 205.2,205.3 206.1, 206.2, 206.3, 211,
212;
100 4 3.75 8
courses in this table in
total and individually
402, , 404
511 Joint underground cables All 100’s; 201, 203, 204,
207, 208, 209, 210, 214; All 401, 402, , 404
98 4.5 3.75 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 26 of 200 © Highway Electrical Skills Academy
HESA Certificated Specialist Course: - Public Lighting – Routine Maintenance Techniques
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs
Learning Hours
Maximum Learner Number
Lantra Awards
Certification for all the courses in this table in
total and individually
214 Safe Isolation Procedures All 100’s; 201 64 4 3.75 8
603 Routine General Maintenance
All 100’s; All 200’s except 202, 205.2,
205.3, 206.1, 211, 212; 402
101 2 2 12
604 Visual Inspection-Optical,
Structural & Electrical
All 100’s; All 200’s except 202, 205.2,
205.3, 206.1, 211, 212; 402, , 603
102 2 2 12
605 Remove and replace components
All 100’s; All 200’s except 202, 205.2,
206.1, 211, 212; 402, , 404; 603, 604
103 2 2 12
HESA Certificated Specialist Course: - Public Lighting – Reactive Maintenance Techniques
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs
Learning Hours
Maximum Learner Number
Certification
for all the courses in this table in
total and individually
214 Safe Isolation Procedures All 100’s; 201 64 4 3.75 8
404 Familiarisation of circuits used in
public lighting All 100’s; 201, 203, 214;
402,
104 2 2 12
604 Visual Inspection-Optical,
Structural & Electrical
All 100’s; All 200’s except 202, 205.2,
206.1, 211, 212; 402, , 603
102 2 2 12
606 Identify and replace faulty
components
All 100’s; All 200’s except 202, 205.2,
205.3, 206.1, 211, 212; 401, 402, , 404; 603,
604, 605
105 6 5.15 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 27 of 200 © Highway Electrical Skills Academy
HESA Certificated Specialist Courses: - Public Lighting - Specialist Skills
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Rec
Learning Hours
Maximum Learner Number
Available individually
701 Diagnose fault & replace faulty
component
All 100’s; All 200’s except 202, 205.2,
205.3, 211, 212; 401, 402, , 404; 604, 605
106 7 6 8
Available individually
702 Emergency Work
All 100’s; All 200’s except 202, 205.2,
205.3, 211, 212; 402, , 404; 604
107 4 3.75 12
Available individually
705 Locate faults on underground
cables
All 100’s; All 200’s except 202, 205.1,
205.2, 205.3, 206.1, 206.2, 206.3, 211, 212;
401, 402, , 404; 604
108 5 4.30 8
Available individually
706 Periodic structural testing
All 100’s; All 200’s except 202, 205.1,
205.2, 205.3, 206.1, 206.2, 206.3, 211, 212
109 7 6 8
Available individually
707 Highway Lighting photometric
testing
All 100’s; All 200’s except 202, 205.1,
205.2, 205.3, 206.1, 206.2, 206.3, 211, 212
110 4 3.75 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 28 of 200 © Highway Electrical Skills Academy
Certification Course Ref No
Title
Pre-requisite Underpinning knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply)
Page
Course Rec
Learning Hours
Maximum Learner Number
Available individually
708 Maintaining high mast lighting
All 100’s; All 200’s except 202, 205.2,
205.3, 206.1, 206.2, 206.3, 211, 212; 402, ,
404; 604
111 7 6 8
Available individually
709 Install high mast lighting
(Specialist Training)
All 100’s; All 200’s (except 202, 205.2, 205.3 206.1, 206.2,
206.3, 211, 212); 404
112 7 6 8
Available individually
710 Awareness of inspection &
testing for witnessing All 100’s; 201, 207, 209,
210; 401, 402, , 404
113 7 6 8
Available individually
714
Initial and Periodic Electrical Inspection and Testing (Public
Lighting )
All 100’s; All 200’s (except 202, 204.1
205.2, 205.3 211, 212); 401, 402, 404; 604
403
115 21 18 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 29 of 200 © Highway Electrical Skills Academy
Section 3 Specialist Course Modules – Additional Modules for Traffic Signs For most operations involving the installation, maintenance and replacement of signs and supporting structures, reference should be made to Section 2. Specifically, the Training Matrix for Traffic Signs – Non-electrical works – refers to courses 501, 502, 503, 504, 505, 506 and 508 in the Public Lighting section. Most of these courses can be applied across both sectors. However, where there are electrical objectives, these have been identified with an asterisk and a note and these should not be applied to Traffic Signs – Non-electrical. The modules below are specialist courses which are not dealt with in the preceding section.
Certificated Specialist Courses: - Signs
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs
Learning Hours
Maximum Learner Number
Note: with 201, 204, 207 & 209
S203 Appreciation of Traffic Sign
Products & associated legislation and guidance
None 53 14 12 12
Available individually S301.7 Excavate & install in
Embankments
All 100’s; 201, 202, 204, 208, 209, 211; 301.1,
302, 501, S203
117 14 12 8
Available individually S501
Erect Columns and Brackets (Posts) over 140mm dia. In
multi-post
All 100’s; 201, 202, 203, 204, 208, 209, 211;
301.1, 302, 501, S203
118 35 30 8
Available individually S512.1
Install sign assembly up to 3 sq. m - sign plate and sign lighting
unit only (excluding connection)
All 100’s; 201, 203, 204, 208, 209; 302, S203
119 4 3.75 8
Available individually S512.2
Install sign assembly 3-15 sq. m - sign plate and sign lighting unit
only (excluding connection)
S512.1 120 7 6 8
Available individually
S512.3
Install sign assembly over 15 sq. m - sign plate and sign lighting unit only (excluding
connection)
S512.2
121 11 9.75 8
Available individually
S513 Install sign on gantries &
overhead structures S512.3
122 14 12 8
Available individually
S707 Inspection and photometric
testing of signs
All 100’s; 201, 203, 204, 208, 209; 302, S203
123 7 6 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 30 of 200 © Highway Electrical Skills Academy
Section 4 Specialist Course Modules – Slot Cutting Certificated Specialist Courses: - Slot Cutting
Certification Course Ref No
Title Pre-requisite
Underpinning knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs
Learning Hours
Maximum Learner Number
Available individually
TSC001 Cut Slot to Specification None
125 7 6 8
Available individually TSC002 Lay Cable and Seal
All 100’s; 201, 202, 204, 208, 209, 211;
301.1, 302, 501, S203
126 7 6 8
Available individually
TSC003 Repair Faulty Cable
All 100’s; 201, 202, 203, 204, 208, 209,
211; 301.1, 302, 501, S203
127 7 6 8
Available individually TSC004 Access to cabinets through ducts
All 100’s; 201, 203, 204, 208, 209; 302,
S203
128 7 6 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 31 of 200 © Highway Electrical Skills Academy
Section 5 Specialist Course Modules – Highway Electronic – Installation of Infrastructure Equipment These courses have been included for completeness and are used to cover any of the Highway Electronic areas. They can also be used as a comparison where sub-contractors have trained their staff to install such equipment. Certificated Specialist Courses: - Installation of Infrastructure Equipment
Certification Course Ref No
Title Pre-requisite
Underpinning knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs
Learning Hours
Maximum Learner Number
Available individually
TIE001 Installation of Supporting Structures (sector / equipment named)
All 100’s; 201, 202, 204, 207, 208, 209, 210; 302;
130 10 9 8
Available individually
TIE002 Installation of Cabinets (sector / equipment type)
All 100’s; 201, 202, 204, 207, 208, 209, 210; 302;
131 4 3.75 8
Available individually
TIE003 Installation of Standard Detection (sector / equipment type)
All 100’s; 201, 202, 204, 207, 208, 209, 210; 302;
132 7 6 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 32 of 200 © Highway Electrical Skills Academy
Section 6 Specialist Course Modules – Traffic Signals Certificated Specialist Courses: - Traffic Signals – General
Certificated Specialist Courses: - Traffic Signals – Installation Techniques
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs Learning Hours
Maximum Learner Number
Available for all the courses in this section of the table in total and individually
M501 Installation of Poles, Lanterns and Brackets - Infrastructure
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209,
210; 302; 402,;
136 10 9 8
M502 Installation of Cabinets and Roots - Infrastructure
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209,
210; 302; 402,;
137 4 3.75 8
Available for all the courses in this section of the table in total and individually
M501 Installation of Poles, Lanterns and Brackets – Non-Infrastructure
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209,
210; 302; 402,;
136 10 9 8
M503 Installation of Standard Detection All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209,
210; 302; 402,;
137 7 6 8
M504 Installation of Underground Cables & Terminations
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209,
210; 302; 402,;
139 7 6 8
M505 Installation of Supply Tails and Earthing
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209,
140 4 3.75 8
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs Learning Hours
Maximum Learner Number
Available individually
M201 Traffic Signal Manual Panel
Operations None
134 4 3.75 12
Note: with 201, 204, 207
& 209
M203 Traffic Product Appreciation None
54 4 3.75 12
Available individually
M301 Traffic Principles M203
135 14 12 12
Highway Electrical Training Specification © HESA
Issue12.17 Page 33 of 200 © Highway Electrical Skills Academy
210; 302; 402,; M405
Available individually
M506 Installation of Ancillary Equipment All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 301.1, 302; 402,;M405
141 14 12 8
Available for all the courses in this section of the table in total and individually
M405 Using Test Equipment on Non-Energised Circuits to BS 7671
All 100’s; 201, M203, 207, 209; 402,;
142 7 6 8
M507 Non-Energised Inspections All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209,
210; 302; 402, M405
143 4 3.75 8
Specialist Courses: - Traffic Signals – Maintenance Techniques
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs Learning Hours
Maximum Learner Number
Available individually
M601a Routine Optical Maintenance of lanterns and PBU’s including cleaning
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302
144 7 6 8
Available for all the courses in this section of the table in total and individually
M601a Routine Optical Maintenance of lanterns and PBU’s including cleaning
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302
144 7 6 8
M601b Maintenance of Pole, Lanterns and Brackets
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402, , M405,713
145 10 9 8
Available individually
M602 Traffic Controller Foundation Principles
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402,
146 11 9.75 8
Available individually
M603 Detection Foundation Principles (Standard)
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402,
147 10 9 8
Available individually
M604 Maintenance of Underground Cables All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402, M405, 713
148 7 6 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 34 of 200 © Highway Electrical Skills Academy
Available individually
M605 Maintenance of Supply Tails and Earthing
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402, M405, 713
149 4 3.75 8
Available individually
M606 Urban Traffic Control Foundation Principles
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402,
150 14 12 8
Available individually
M607 Monitoring and Control Foundation Principles
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402,
151 14 12 8
Available individually per employee
over 18mth basis
M608 Pedestrian Traffic Controller Maintenance for (Named)
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402, M405, 713
M301, *M602
152 14 12 8
Available individually per employee over 18mth basis
M609 Junction Traffic Controller Maintenance for (Named)
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402, M405, 713
M301, *M602
153 14 12 8
Available for all the
courses in this section of
the table in total and
individually
M603 Detection Foundation Principles (Standard)
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402,
147 10 9 8
M611 Maintenance of Specific Detection Equipment (Named):
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402, M405, 713
M603
154 7 6 8
Available individually per employee over 18mth basis
M611 Maintenance of Specific Detection Equipment (Named) -
All 100’s; 201, 202, M203, 204, 205.1, 207, 208, 209, 210; 302; 402, M405, 713
M603
154 7 6 8
The Traffic Controller Foundation Principles, M602 course is a mandatory pre-requisite for M608/9 courses, except where a Learner has already attended a M608/9 course within five years of the course start date and has worked on Traffic/Pedestrian Controllers within the last year The Detector Foundation Principles, M603 course is a mandatory pre-requisite for M611 courses, except where a Learner has already attended a M611 course within five years of the course start date and has worked on various different detectors within the last year. The Course M301 is a mandatory course for courses M608 and/or M609, except where there is evidence of previously undertaking the course M301, or where substantiated evidence can be provided and verified that the Learner has been working continuously within the sector for the last 5 years at such a level that the course M301 objectives can be met. The Training center is required to hold all supporting documents within the course administration folder.
Highway Electrical Training Specification © HESA
Issue12.17 Page 35 of 200 © Highway Electrical Skills Academy
Specialist Courses: - Traffic Signals – Specialist Skills
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs Learning Hours
Maximum Learner Number
Available individually
M405 .
Using Test Equipment on Non-Energised Circuits to BS 7671
All 100’s; 201, M203, 207, 209; 402, 137
142 7 6 8
Available individually
M701 Commissioning Procedures All 100’s; 201, M203, 207, 209, 210; 401, 402, 403; M405, .; 713 All M600’s
155 14 12 8
Available individually
M702 Transmission Systems and Techniques Fundamentals (Named)
All 100’s; 201, M203, 207, 209, 210; 401, 402, 403;
M405, .; 713
156 14 12 8
Available individually
M703 Traffic Signals Configuration (Named)
Equipment Code: - All 100’s; 201, M203, 207, 209, 210; 401, 402, 403;
M405, .; 713
157 21 18 8
Available individually
M704 Advanced Traffic Principles All 100’s; 201, M203 158 14 12 8
Available individually
M705 Advance Detection Techniques (Named)
All 100’s; 201, M203,204, 205.1, 207, 209; 302; 401, 402, 403, M405, .; 713 M603
159 7 6 8
Available individually
M706 Ancillary Control and Monitoring Equipment Skills (Named)
All 100’s; 201, M203,204, 205.1, 207, 209; 302; 401, 402, 403, M405, M607; M702
M606
160 14 12 8
Available individually
M707 Monitoring Equipment Skills (Named) All 100’s; 201, M203,204, 205.1, 207, 209; 302; 401, 402, 403, M405,
M607, M702 161 14 12 8
Available individually
M708 Microprocessor Optimised Vehicle Actuation Maintenance (Named)
All 100’s; 201, M203, 204, 205.1, 207, 209; 302; 401, 402, 403, M405, 713
162 28 24 8
Available individually
M709 Road Transport Passenger Information Systems (Named)
All 100’s; 201, M203, 204, 205.1, 207, 209; 302; 401, 402, 403, M405,
163 28 24 8
Available individually
713 Initial and Periodic Electrical Inspection and Testing (Traffic
Control)
All 100’s; 201, 202, M203, 204.1, 205.1, 207, 208, 209, 210; 302; 401, 402, , M405,
403
164 21 18 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 36 of 200 © Highway Electrical Skills Academy
Section 7 Specialist Course Modules – Communications Certificated Specialist Courses: - Communications
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs Learning Hours
Maximum Learner Number
Available individually
TCOM001 Communications Fundamental
Principles None
166 17 15 8
Available individually
TCOM002 Communications Detection
Fundamental Principles TCOM001
167 10 9 8
Available individually
TCOM003 Installation of non-Infrastructure
Equipment Communications
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210;
302; TCOM001, TCOM002
168 14 12 8
Available individually
TCOM004 Maintenance of cables for
Communications
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302; 402; 712,TCOM001,
TCOM002
169 7 6 8
Available individually
TCOM005 Maintenance of specialist
Communications equipment (Named)
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210;
302;
TCOM001, TCOM002
170 10 9 8
Available individually 716
Initial and Periodic Electrical Inspection and Testing
(Communications)
All 100’s; 201, 202, M203, 204.1, 205.1, 207, 208, 209, 210; 302; 401, 402, M405,
403
171 21 18 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 37 of 200 © Highway Electrical Skills Academy
Section 8 Specialist Course Modules – Variable Message Signs Certificated Specialist Courses: - Variable Message Signs
Lantra Awards
Certification
Course Ref No
Title Pre-requisite Underpinning
knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs Learning Hours
Maximum Learner Number
Available for all the courses in this section of the table in total and individually
TVMS001 Installation of non-Infrastructure
Equipment - VMS
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210;
302;
173 14 12 8
TVMS002 Maintenance of specialist VMS
equipment (Named)
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210;
302;
174 10 9 8
TVMS003 Commissioning Procedures – VMS (Named)
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210;
302; 402; 403; 712
175 7 6 8
TVMS
001/002/003
- VMS Installation non-Infrastructure, Maintenance and commissioning of (Named)
As above stated individually
As above 21 18 8
Section 9 Specialist Course Modules – Env. & Monitoring Equip’t
Certificated Specialist Courses: - Env. & Monitoring Equipment
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs Learning Hours
Maximum Learner Number
Available individually
TME001 Env. & Monitoring Equip’t Fundamental Principles
None 177 17 14 8
Available individually TME002
Installation of non-infrastructure Env. & Monitoring Equip’t
All 100’s; 201, 202, 204, 205.1, 207, 208, 209,
210; 302;
178 14 12 8
Available individually TME003
Maintenance of Env. & Monitoring Equip’t
All 100’s; 201, 202, 204, 205.1, 207, 208, 209,
210; 302;
179 7 6 8
Section 10 Specialist Course Modules – Cameras
Highway Electrical Training Specification © HESA
Issue12.17 Page 38 of 200 © Highway Electrical Skills Academy
Certificated Specialist Courses: - Cameras
Certification Course Ref No
Title Pre-requisite Underpinning
knowledge
Mandatory Pre-requisite certificated training (note
alternative provision may apply) Page
Course Hrs Learning Hours
Maximum Learner Number
Available individually
TCAM001 Install Data Communications Cable All 100’s; 201, 202, 204, 205.1,
207, 208, 209, 210; 302;
181 7 6 8
Available individually
TCAM002 Terminate Cable All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302; 402;
182 7 6 8
Available individually TCAM003
Installation of non-Infrastructure Equipment – Camera / Head
assembly
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302;
183 3.5 3.5 8
Available individually
TCAM004 Routine optical maintenance of
cameras
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302;
184 3.5 3.5 8
Available individually
TCAM005 Maintenance of Camera / Head
assembly
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302;
185 7 6 8
Available individually TC AM006 Maintenance of cable
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302; 402;
403; .; 712
186 7 6 8
Available individually
TCAM007 Detector Maintenance for (Named)
Equipment
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302; M603
187 7 6 8
Available individually
TCAM008 Commissioning Procedures for
Camera (Named)
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302; M603
188 14 12 8
Available individually
TCAM009 Transmission Systems and Techniques Fundamentals
All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302; M603
189 7 6 8
Available individually
TCAM010 Ancillary Equipment Skills (Named) All 100’s; 201, 202, 204, 205.1, 207, 208, 209, 210; 302; M603
190 14 12 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 39 of 200 © Highway Electrical Skills Academy
Combination (Amalgamated) Course Durations
Course Combination Codes Pre-
requisites Course
Hrs
Course Learning
Hrs
Maximum Learner Number
101 to 106 Combined Combination - Health, Safety, Environment, COSHH, Electrical Safety, Moving and Lifting, Legislation and Standards, Emergency Preparedness
As per individual
course 17 16 12
201-203*-204-207 209 Combined Combination - Appreciation of Public Lighting and T/Sign Equipment, Hazards and Risks, Hand Held Tools Including Operating Hand Held Drills/ Screwdrivers, PPE and On Site Safety
As per individual
course 19 17 8
201-S203-204-207 209 Combined Combination - Traffic Sign Products & associated legislation and guidance, Hazards and Risks, Hand Held Tools Including Operating Hand Held Drills/ Screwdrivers, PPE and On Site Safety
As per individual
course 27 24 8
201-M203-204-207 209 Combined Combination-Traffic Product Appreciation, Hazards and Risks, Hand Held Tools Including Operating Hand Held Drills/ Screwdrivers, PPE and On Site Safety
As per individual
course 19 17 8
302.1 and 302.2 Combination Course - Installing, Maintaining and Removing Temporary Traffic Management, Positive Traffic Control Including Temporary/Portable Traffic Signal Equipment on Rural and Urban Roads
As per individual
course 11 10 8
211 and 212 Combined Combination -Lorry Mount Crane Slinger, Signaller and Operator
As per individual
course 11 10 8
401.1, 402 & 403 Combined Combination - Basic Electrical Theory, EAWR, IET Wiring Regulations
As per individual
course 26 22 12
501 to 504 Combined Combination - Install Feeder Pillars and Erect, Remove, Re-align Columns and Brackets
As per individual
course 7 6 8
505 and 508 Combined Combination - Installation of Bollard Base and Base Lit Bollard
As per individual
course 7 6 8
506 and 507 Combined Combination - Installation of Lantern, Bracket, Wiring and Control Gear
As per individual
course 7 6 8
510 and 511 Combined Combination - Terminate, Connect U/G Cable into Cut Out and Joint Underground Cables
As per individual
course 7 6 8
214, 603, 604, and 605 Combined Combination - Safe Isolation, Routine Maintenance, Optical, Structural and Electrical Visual Inspection and Remove and Replace Components
As per individual
course 8 7.5 8
604, and 606 Combined Combination - Safe Isolation, Familiarisation of Public Lighting Circuits, Optical, Structural and Electrical Visual Inspection, Identify and Replace Faulty Components
As per individual
course 11 10 8
M501, M502 Combined Combination - Installation of Poles, Lanterns, Brackets, Cabinets and Roots - Infrastructure
As per individual
course 11 10 8
M501, M503, M504 and M505 Combined Combination - Installation of Poles, Lanterns, Brackets, standard detection, underground cables terminations, supply tails and earthing
As per individual
course 22 20 8
M405 and M507 Combined Combination - Non-Energised Inspections and Using Test Equipment to BS 7671
As per individual
course 9 8 8
M601a and M601b Combined Combination -Maintenance of Pole, Lanterns, Brackets and Routine Optical Maintenance and Cleaning of Lanterns and PBU's
As per individual
course 14 12 8
M603 and M611 Combined Combination - Detector Foundation Principles and Maintenance of Specific Detection Equipment for Equipment Type;
As per individual
course 14 12 8
801 and 802 Combined Combination - Coordinate the work of others on site set to work, monitor Quality, Safety and Productivity of Teams
As per individual
course 17 15 12
TCAM 003 to 005 Combination - Camera, Head assembly Maintenance and non-infrastructure installation and Routine Optical Maintenance for Equipment Type;
As per individual
course 14 11 8
TVMS001 to 003 Combined Combination As per
individual 21 18 8
Highway Electrical Training Specification © HESA
Issue12.17 Page 40 of 200 © Highway Electrical Skills Academy
course
204.1 Vibrating Plate - Flat Plate, Trench Rammer, Single/Double Vibrating Roller Drum
As per individual
course 7 7 4
M602 and M609 Combined Combination - Traffic Controller Foundation Principles and Junction Traffic Controller Maintenance for Equipment Type;
As per individual
course 25 21 8
Note
1. Combination Courses are required to be delivered within the same period without ‘gaps’ and delivered by the approved trainer/s, from the same training organisation where the nominated lead trainer is also delivering on the course. This is regardless of the number of Learners attending, up to the maximum specified
2. Where a combination course appears in more than one combination group, ie 214, then this course does not have to be repeated in subsequent combination groups. Training Providers to refer the Requirements for Approved Training Organisations and Approved Trainers Section 9 for full details.
3. The combination course is to be delivered over the allocated time period, as specified by the Course duration clarification.
4. Where there is a course within the combination with a maximum number of 8 Learners, then this is the maximin number for all courses within the combination group.
Conversion Courses A conversion course is a course that updates Learners on a particular specific product which forms part of the same family.
• The conversion course is delivered to the same level of Course Syllabus specification.
• The duration of the conversion course may be up to, the same period or greater than that of the initial equipment delivery period.
• Learners must have successfully completed the original course or can demonstrate prior occupational knowledge (HERS evidence) before they can be considered for registration to a conversion course.
• Naming of the conversion course will form part of the product directory within the ‘TRAM’ on a centre basis request
Highway Electrical Training Specification © HESA
Issue12.17 Page 41 of 200 © Highway Electrical Skills Academy
Section 1 –Common Modules
Sectio
n 1
–C
om
mo
n M
od
ule
s
Highway Electrical Training Specification © HESA
Issue12.17 Page 42 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Emergency First Aid at Work (EFAW) COURSE REFERENCE: None DURATION: 6 hours (Minimum Duration)
CERTIFICATION: By approved providers COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with the initial knowledge to administer emergency first aid to preserve life, prevent situations from worsening and promote recovery before a fully trained paramedic or ambulance technician arrives PREREQUISITES: There are no pre-defined prerequisites for attending this training. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will be able to:
• state the role and responsibilities of the first-aider including reference to: • the importance of preventing cross-infection • the need for recording incidents and actions • use of available equipment • completing an accident report form
• assess the situation and circumstances of an incident in order to act safely, promptly and effectively in an emergency
• manage an unresponsive casualty who is breathing normally
• manage an unresponsive casualty who is not breathing normally including administering cardiopulmonary resuscitation (CPR)
• apply and use an automated external defibrillator (AED)
• recognise and assist a casualty who is choking
• manage a casualty with external bleeding
• manage a casualty who is in shock
• manage a casualty with a minor injury (grazes, bruises, burns, scalds and splinters)
COURSE TOPICS:
The Role and Responsibilities of the First Aider The Situation Assessment Administering First Aid – Unconscious Administering Cardiopulmonary Resuscitation Administering First Aid – Conscious: -
• Choking • External Bleeding • Shock • Minor Injuries
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 43 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Health, Safety and Environment at Work COURSE REFERENCE: 101 DURATION: 4 hours (Recommended Minimum Duration)
COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with an understanding and awareness of Health, Safety and the Environment; their individual and collective responsibilities under the organisation Health and Safety Policy, Health and Safety at Work etc. Act 1974; and Environmental Legislation PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify a Health and Safety Policy.
• State the employer’s obligations from the HASAWA.
• State the employee’s obligations from the HASAWA.
• Explain the Accident Reporting and Investigation procedure.
• State the purpose of Risk Assessments.
• Explain the importance of housekeeping including waste re-use, re-cycling and disposal
• Identify how work activities could impact on environmental issues COURSE TOPICS:
• The Health and Safety at Work Act.
• Organisation H&S Policies & Procedures
• Responsibilities: individual and organisation
• Accidents and Reporting.
• Environmental Policy and obligations
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 44 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Principles of control of substances which are hazardous COURSE REFERENCE: 102 DURATION: 4 hours (Recommended Minimum Duration)
COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with an understanding and awareness of the control of substances which are hazardous; their individual and collective responsibilities under organisational and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify substances likely to cause harm.
• Follow COSHH assessment instructions.
• Identify the required PPE correctly.
• Identify actions before using substances.
• Identify the measures required to ensure the safety of employees and the general public.
• Explain actions required on contact with substances. COURSE TOPICS:
• Identification markings.
• Other potentially hazardous substances covered by legislation other than COSHH (e.g. asbestos, lead)
• How substances enter the body
• Assessment Sheets.
• Reducing the Risk.
• The Management role and responsibilities.
• The COSHH assessor role and responsibilities.
• The Users role and responsibilities.
• First Aid actions. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 45 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Electrical Safety COURSE REFERENCE: 103 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with an understanding and awareness of Electrical Safety and their individual and collective responsibilities under organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify injuries caused by electricity.
• State the difference between direct and indirect contact.
• Explain the effects of electric shock to the human body
• Identify measures to prevent electrical injuries.
• Follow organisation procedures.
• State the reasons for inspection & testing of fixed and portable equipment.
COURSE TOPICS:
• Injuries from electricity.
• Types of contact.
• Effects on the human body.
• Measures to prevent electrical injuries.
• Awareness of Electricity at Work Regs; G39
• Inspection & testing principles.
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 46 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Moving and Handling COURSE REFERENCE: 104 DURATION: 3 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with an understanding and awareness of Moving and Handling and their individual and collective responsibilities under the organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative written and practical assessment will follow the completion of this course or group of
courses. OBJECTIVES: On completion of the course learners will:
• Identify associated hazards before and during the handling of materials.
• Identify the associated risks.
• Identify and use required PPE correctly.
• Carry out assessment of items to be handled and associated risks.
• Carry out correct lifting techniques.
• Identify alternative handling methods. COURSE TOPICS:
• The spine
• Definition of Handling
• Moving and Handling Operations Regulations and obligations
• Identification of hazards.
• Reducing the risks.
• Management responsibilities.
• Employee responsibilities.
• Lifting equipment.
• Lifting methods. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 47 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Interpretation of Legislation & Standards COURSE REFERENCE: 105 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with an awareness of and the skills required to establish where to look for advice and information relating to relevant legislation and standards other than the Health & Safety at Work Act, the Electricity at Work Regulations, BS7671, COSHH Regulations, Manual Handling Regulations and the Personal Protective Equipment Regulations which are covered elsewhere (if this is not the case for an individual learner, the general principles should be covered). PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• State the hierarchy of documents in relation to health and safety legislation
• Identify the key legislation and guidance relating to risks in highway electrical works
• Identify where standards to be reached in respect of risk assessments can be found
▪ State what action is to be taken in response to defined signs under the H&S (Safety Signs & Signals) Regulations
COURSE TOPICS:
• Key Regulations & ACoPs – e.g. Management, , CDM, LOLER, Noise at Work, PUWER, RIDDOR, Work at Height, Workplace (Health, Safety & Welfare)
• H&S (Safety Signs & Signals) Regulations
• H&S Guidance Notes – e.g. HSG(6), HSG(47)
• Industry Guidance PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 48 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Emergency Preparedness COURSE REFERENCE: 106 DURATION: 2 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with the knowledge and practical key skills required for planning and applying responses to emergencies in the workplace. This does not cover emergency attendance or emergency works to damaged or faulty highway electrical equipment PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify activities likely to require emergency action
• State the first element of the emergency first aid primary survey
• State the correct action to take in the case of a LV & HV electrical injury
• State the method of dealing with potential pollution to the environment from a spill
• Identify when and how to obtain assistance COURSE TOPICS:
• Electrical & other injuries
• Works vehicle accident
• Vehicle malfunctions
• Emergency First Aid procedures & their limitations PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 49 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Hazard Identification and Risk Assessment COURSE REFERENCE: 201 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to carry out Hazard identification and Risk assessments according to organisation policy and complete associated documentation. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A practical assessment will take place during the course where learners will be required to complete a suitable and sufficient risk assessment. A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Follow associated organisation risk assessment procedures
• Identify hazards
• Identify risks.
• Carry out a risk assessment.
• Identify measures needed to reduce risk.
• Correctly record risk assessments
• Identify when and how to report hazards and risks considered to be excessive or requiring further control measures
• Ensuring site is safe for work to proceed or finish.
• Conduct themselves in a safe and professional manner on site COURSE TOPICS:
• Definitions of hazard and risk.
• Identifying hazards in the workplace.
• Identifying significant hazards
• Assessing risks.
• Measures to reduce risks.
• Recording risk assessments.
• Personal conduct on site PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 50 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Appreciation of Public Lighting and illuminated Traffic Sign
Equipment and its use on the Highway COURSE REFERENCE: 203 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning knowledge regarding the different types of public lighting equipment, including traffic sign equipment, and boundaries for its use on the public highway. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A multi-choice summary assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Confirm site details and define boundaries
• Identify different types of equipment under, on and over the highway
• Explain the scope of work likely to be carried out on different types of equipment
• State the application of common types of public lighting systems.
• Identify different power supply equipment
• Confirm the suitability of fixing methods for public lighting systems in the environment of the installation including the threat from vandalism and unauthorised access.
• Explain how to dispose of public lighting equipment and components
COURSE TOPICS:
• The need for public lighting
• Different types of equipment
• Different types of Highways
• Use of equipment on different Highways
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 51 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Hand held Tools including Operating Hand Held
Drills/Screwdrivers COURSE REFERENCE: 204 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to identify associated hand and power tools hazards and risks and the correct use and operation of powered hand held drills and screwdrivers PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course, OBJECTIVES: On completion of the course learners will:
• Identify the Hazards and Risks when using non-powered Hand Tools.
• State the hazards of Powered Tools
• State the appropriate PPE when using Hand held Tools
• State the requirements for the Provision and Use of Work Equipment Regulations 1998
• State what action is required in the event of identifying defects
• Identify how to store hand tools
• Correctly pre-check and test hand held drills and Screwdrivers before use
• Correctly use handheld powered drills on a range of materials COURSE TOPICS:
• Typical types of hand held tools (non powered)
• Tool identification, checks maintenance and safety
• Basic maintenance of tools.
• Correct use of Hand Held Powered Drills
• Limitations and identifying the hazards.
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 52 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Personal Protective Equipment COURSE REFERENCE: 207 DURATION: 4 Hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to carry out correct assessment and evaluation of Personal Protective Equipment in accordance with current organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
* State the common types of Personal Protective Equipment available
* Identify the need for Personal Protective Equipment. * Use Personal Protective Equipment appropriate for the tasks and
the environment. * Follow organisation and legislative procedures for use &
maintenance COURSE TOPICS:
* Hazards and Risks requiring the use of PPE. * How substances enter the body * Tasks, risks and using PPE, including limitations. * Organisation and legislative procedures. * Types of Personal Protective Equipment.
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 53 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: On Site Safety COURSE REFERENCE: 209 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to correctly define site-working areas and confirm site details before and during work activities. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
* Check and confirm site details. * Identify hazards and risks on site. * Define the site working area. * Assess ground works. * Correctly prepare and store equipment on site safely. * Identify and use associated organisation policies & procedures. * Ensure the site is safe for work to proceed or finish * Conduct themselves in a safe and professional manner on site * Identify a Confined Space, hazards and actions required
COURSE TOPICS:
* Identifying typical significant hazards. * Assessing risks. * Working practices * Transporting goods on site. * Assessing and securing loads. * Site safety practices. * Organisation policies. * Confined Spaces
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 54 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Appreciation of Traffic Sign Equipment & associated legislation
& guidance
COURSE REFERENCE: S203
DURATION: 14 hours (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working within the Highway electrical Sector with an awareness of traffic sign products and related relevant legislation, publications, skills and standards relating to the Road traffic Sign Industry other than Health & Safety legislation which is covered elsewhere.
PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents.
ASSESSMENT: A summative assessment will follow the completion of this course or group of courses.
OBJECTIVES: On completion of the course learners will:
• Identify correct size/type of sign / post for road environment.
• Correctly site sign assemblies in accordance with status/speed of road, traffic orders etc.
• Identify appropriate offsets and mounting heights in accordance with status of road and the presence of other furniture eg safety fences.
• Report variations. COURSE TOPICS:
• Traffic Sign Products and fixings
• Route classifications and sign colours.
• Sizes and siting of signs.
• Signing requirements for traffic orders, cameras etc.
• Current requirements for illumination.
• Current requirements for passively safe posts/protection.
• Overview of EN12899
• Waste Management Duty of care. PRACTICAL: To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 55 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Traffic Product Appreciation COURSE REFERENCE: M203 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Traffic Sector the underpinning knowledge to associate with the basic build blocks that constitute a standard Traffic Junction. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• State the need for Traffic Control Measures.
• Identify 3 modes of traffic control.
• State 10 or more basic traffic related terms.
• Identify basic detection methods.
• State the two common Traffic Control Types.
• State other methods of remote junction control. COURSE TOPICS:
• The need to control Traffic.
• Controller Modes.
• Using Traffic Sector terminology.
• Detection methods overview.
• The Junction and Pedestrian control methods.
• Remote methods of junction control. PRACTICAL:
To enable maximum learning and benefit from this course, there will be several exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 56 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Avoiding Danger from Underground Services (training designed
to meet the assessment requirements of Unit 1 NRSWA 1991) COURSE REFERENCE: 202 DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS This course aims to provide suitably qualified employees working within the Highway Electrical Sector the underpinning skills required to understand and use equipment to avoid danger from underground services. Additionally this course aims to provide sufficient knowledge to undertake the Assessment for Unit 1 of the NRSWA 1991. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A practical assessment will form part of this course, which will include an assessment on the use of appropriate detection equipment and drawings to locate underground services. . OBJECTIVES: On completion of the course learners will:
• Identify associated Hazards.
• Identify a Safe System of work.
• Demonstrate the correct location of services using Site Drawings
• Identify underground services
• State the need for Underground Service Avoidance
• Demonstrate the correct use of underground services drawings
• Demonstrate the correct use of the Cable Avoidance Tool.
• Demonstrate the correct use of the Generator and Ancillary equipment.
• State the need for Safe Excavation/digging COURSE TOPICS:
• Identification of hazards.
• Safe Systems of Work and HS (G) 47.
• Site drawings
• Service types
• Introduction to CAT & Genny
• Operation of Cable Avoidance Tools.
• Operation of Generators.
• Using the CAT in conjunction with a Sonde
• .Safe Excavation PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of learner exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 57 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Hand and Power Tools (named – Specific Equipment) COURSE REFERENCE: 204.1 DURATION: Various see page 18 Safe working Practices (Recommended Minimum Duration, this is dependent on equipment type and environment of use) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to operate specific powered hand tools and associated hazards and risks. . PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course, OBJECTIVES: On completion of the course learners will:
• Identify the Hazards and Risks when using the specific Power Tools
• Identify the required PPE
• Identify appropriate legislation requirements
• Identify checks to be carried out before use
• State what action is required in the event of identifying defects
• Take appropriate care and maintenance of the specific power tools
• Identify how to store specific power tool
• Identify precautions with specific power tool
• Correctly start and stop the named power tool
• Correctly use the named power tool for the intended purpose and environment, and where appropriate attachment of tool, blade or disc.
COURSE TOPICS:
• Legislation requirements
• Tool identification, checks maintenance and safety
• Basic maintenance of specific tools.
• Limitations and identifying the hazards.
• Correct use of power tools
• Correct attachment of tool, blade or disc PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 58 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Working at Height with Steps and Ladders COURSE REFERENCE: 205.1 DURATION: 4 Hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to carry out correct methods of access to fix above ground equipment. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment consisting of an onsite practical and written theory will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Define working at height
• Follow associated organisation procedures and method statements.
• Carry out an inspection of the ladders / steps
• Complete hazard and risk assessment documentation.
• Identify the correct method for planning and gaining access.
• Identify and use correct PPE.
• Demonstrate correct use of other safety equipment. COURSE TOPICS:
• Organisation procedures and method statements.
• Inspection of access equipment
• Using ladders and / or step ladders
• Other access equipment
• Work at Height Regulations
• Safety equipment.
• Setting and positioning of ladders, including correct methods of securing (demonstration)
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 59 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Working at Height with Scaffolding Towers COURSE REFERENCE: 205.2 DURATION: 2 Hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to carry out correct methods for the erection and use of Scaffolding Towers. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Follow associated organisation procedures and method statements.
• Complete hazard and risk assessment documentation.
• Identify the correct method for planning and gaining access.
• Identify and use correct PPE.
• Demonstrate correct use of safety equipment.
• Correctly use the appropriate work belts and support. COURSE TOPICS:
• Organisation procedures and method statements.
• Using Scaffolds.
• Work at Height Regulations
• Safety equipment. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 60 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Prefabricated Mobile Access and Working Towers COURSE REFERENCE: 205.3 DURATION: 5 Hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide the knowledge and practical skills required for Operatives working within the Highway Electrical Sector to Erect, Operate and Maintain Prefabricated Mobile Access and Working Towers including responsibilities under the organisation and legislative policies PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment consisting of an onsite practical will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Identify the Prefabricated Mobile Access and Working Towers system concept
• Explain the operating specifications
• Identify the operational & safety critical components
• Be able to position the Tower, set up and use safely
• Explain pre-user checks and maintenance criteria
• Confirm the requirements of towing mobile Towers and required checks COURSE TOPICS:
• Concept of the Monkey Tower system
• Component parts of the Monkey Tower
• Monkey Tower safety
• The requirements for towing
• Using the Monkey Tower in a roadway or footway; signing and guarding
• Setting up the Monkey Tower in a safe location and safe manner
• Operating specifications and constraints
• Maintenance requirements
PRACTICAL:
To enable maximum learning and benefit from this course, there will a practical session. This will be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 61 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: MEWP Awareness COURSE REFERENCE: 206.1 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with an awareness of the skills required to carry out correct assessment measures before using MEWPs. It also provides supervisory management with the knowledge to determine if operatives are using MEWP equipment correctly. This course does not provide the employee with the required skills to operate Boom, Scissor or any other type of MEWP plant. Where employees are required to set to work and operate MEWP equipment as part of their work activity, the list of alternative Training provision must be reviewed for appropriate training and assessment. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Identify hazards present at the place of work.
• Confirm suitability of access equipment.
• Confirm safe working loads.
• Confirm the effects of weather conditions of safe operations.
• Complete a Plan for the lift and a risk assessment
• State the requirements for appropriate Personal Protective Equipment.
• Assess appropriate guarding appropriate to site. COURSE TOPICS:
• Regulations
• Hazards.
• Types of equipment.
• Assessing suitability, working loads and weather conditions.
• Planning and risk assessments
• PPE.
• Signing and Guarding. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 62 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Loading, Transporting and Removing of Goods (Vehicular) COURSE REFERENCE: 208 / M208 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to correctly load, secure and transport goods to site in a safe manner in accordance with current organisation and legislative policies. This course excludes lorry loaders. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Identify hazards and risks. • Load vehicles with equipment in a safe manner. • Secure & store equipment in a safe manner. • Identify and use safe working practices to load and unload
equipment. • Use correct methods for transporting goods on site • Assess Loads to be handled/transported. • Identify when and how to seek assistance. • Assessment of Towing including Kerb, nose and weight
COURSE TOPICS:
• Loading of vehicles. • Securing of loads • Identifying hazards. • Assessing risks. • Working practices • Transporting goods on/to site. • Assess loads • Vehicle to Trailer Ratio including correct calculations • VOSA guidance
. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 63 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Working in the vicinity of DNO / IDNO equipment including G39 COURSE REFERENCE: 210 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with the appropriate safety knowledge and practical key skills required for work in the vicinity of DNO equipment. This includes overhead power lines and the removal and replacement of DNO cut-out fuse carriers in a safe and responsible manner and to comply with the responsibilities under organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements are shown in the Contents. Certificated evidence of successfully completing Course 214 Safe Isolation Procedures required ASSESSMENT: A summative assessment and a practical assessment will follow the completion of this course OBJECTIVES: On completion of the course learners will:
• State the associated Hazards and Risks.
• State the acceptable clearances between lighting columns and overhead lines.
• State the different methods of providing a mains supply.
• Describe their responsibilities regarding commissioning, maintenance, repair and emergency attention.
• State the method of work to be adopted when working in the vicinity of live conductors.
• List the PPE requirements.
• Demonstrate the ability to correctly remove and replace a cut-out fuse carrier for isolation purposes and fuse replacement.
• Carry out a polarity check COURSE TOPICS:
• Electrical Injuries.
• Overview of EREC G39 Issue 2 2013
• Overview of ILP HV OHL Supplement to the ILP CoP for Electrical Safety in Highway Electrical Operations
• PPE
• Statutory requirements.
• Means of providing electricity supplies.
• Commissioning, Maintenance, Repair and Emergency Attention including supply cable insulation shrinkage.
• Cut-out fuse carrier removal and replacement procedures. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 64 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Work in the Vicinity of DNO / IDNO Equipment Awareness (Incl. G39)
COURSE REFERENCE: 210.1 DURATION: 5 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide suitably qualified Engineers and HERS registered operatives with the knowledge required for working in the vicinity of DNO / IDNO equipment- including overhead lines in a safe and responsible manner and to comply with their responsibilities under organisation and legislative policies. This course excludes the removal and replacement of DNO cut-out fuse carriers PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course OBJECTIVES: On completion of the course learners will:
• State the associated Hazards and Risks.
• State the acceptable clearances between lighting columns and overhead lines.
• State the different methods of providing a mains supply.
• State the responsibilities of operatives regarding commissioning, maintenance, repair and emergency attention.
• State the method of work to be adopted when working in the vicinity of live conductors.
• List the PPE requirements.
• State the correct procedure to remove and replace a cut-out fuse carrier for isolation purposes and fuse replacement.
COURSE TOPICS:
• Electrical Injuries.
• Overview of EREC G39 Issue 2 2013
• Overview of ILP HV OHL Supplement to the ILP CoP for Electrical Safety in Highway Electrical Operations
• PPE
• Statutory requirements.
• Means of providing electricity supplies.
• Commissioning, Maintenance, Repair and Emergency Attention including supply cable insulation shrinkage.
• Cut-out fuse carrier removal and replacement procedures. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 65 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Safe Isolation COURSE REFERENCE: 214 DURATION: 4 hrs (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working within the Highway Electrical Sector with an understanding and awareness of the procedures for the safe isolation of electrical circuits. The course will also cover the procedures for the safe method for the testing of supply and the checking of polarity. Course 210 Working in the vicinity of DNO/IDNO Equipment will be required for operatives working onsite and carry out isolation in the vicinity of DNO/IDNO equipment; this course should also be considered for any operative carrying out isolation on non-DNO/IDNO equipment PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* State the methods for the isolation of electrical circuits in differing highway electrical equipment.
* Test to determine if a supply is available. * Check to confirm a supply is isolated * Check to confirm the polarity of the supply * Identify the steps required to carry out safe isolation * What action to take in the event that the supply cannot be restored.
COURSE TOPICS:
* Safe isolation. * Testing to determine availability of supply and the use of appropriate
equipment. * Switching * Protective devices used in Highway Electrical works. * Reporting procedures
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 66 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Emergency attendance to Highway Electrical Equipment COURSE REFERENCE: 215 (Previously 307 / 607) DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide operatives working in the Highway Electrical sector the knowledge and skills required to attend an emergency, assess the requirements for any work that maybe necessary and call for assistance where work that is required is beyond the competency level of the employee. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify hazards and risks * Take necessary precautions before, during and after completion of
works * Assess the emergency and carry out any work to make the site safe &
secure to protect public, road users, livestock from danger. * Decide on the need or otherwise to report to supervisor for advice and
instructions. * Decide on the need or otherwise to call out the DNO * Report actions and additional work required.
COURSE TOPICS:
* Hazards and risks * On site precautions * Communication of technical information to relevant persons * Assessment of site conditions under emergency situations
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 67 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Brush Painter – Apply Surface Protection COURSE REFERENCE: 602 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working within the Highway Electrical Sector with an understanding and awareness of the correct preparation and application of surface protection treatments applied on site. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: Formative assessments will take place during the course, with a summative practical assessment at the end of this course.
OBJECTIVES: On completion of the course learners will:
* Identify Health and Safety hazards, including Electricity and Air
Supply Safety Data Sheets (SDS) Safety Limits (LEL, TLV, OEL,
MEL), Ventilation and Paint Application
* Identify coating Types and Systems
* Use Products Data Sheets - Review
* Identify Single and Two Part Materials and Paint Mixing
* Pot-Life and Induction
* Check Storage, Batch Numbers, Coverage and Compatibility
* Determine Volume Solids
* Calculate Coverage
* Understand the impotence of Relative Humidity, Dew Point, Steel
Temperature Drying and Recoating (inc, cure)
* Use correct Brush Application
COURSE TOPICS:
* Health & Safety.
* Coating types
* Coating application PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 68 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Fettler COURSE REFERENCE: 602a DURATION: 1 day (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working within the Highway Electrical sector with the underpinning knowledge to be able to prepare surfaces ready for coating applications PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which may be required before attending. A complete list of pre-course requirements is shown in the Contents of the Highway Electrical Training Specification ASSESSMENT: Formative assessments will take place during the course, with a summative practical assessment at the end of this course.
OBJECTIVES: On completion of the course learners will:
* Identify Health and Safety hazards, including Electricity and Air
Supply Safety Data Sheets (SDS) Safety Limits (LEL, TLV, OEL,
MEL), Ventilation
* Identifying Safety in Paint Application
* Recognise and apply coatings to Galvanizing
* Apply use of Hand Wire Brush for surface preparation
* Apply and use Solvent for Cleaning
COURSE TOPICS:
* Health & Safety
* Surface Preparation
PRACTICAL: To enable maximum learning and benefit from this course, learners will carry out a practical exercise demonstrating the use of PPE and RPE. They will also prepare galvanised steel, clean surfaces using solvent cleaning use hand wire brushes.
Highway Electrical Training Specification © HESA
Issue12.17 Page 69 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Spray Painter COURSE REFERENCE: 602.5 DURATION: 21 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working within the Highway Electrical sector with the underpinning knowledge to be able to safely set up, operate, clean, maintain and store airless spray equipment PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which may be required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: Formative assessments will take place during the course, with a summative practical assessment at the end of this course.
OBJECTIVES: On completion of the course learners will:
* Identify Health and Safety hazards, including Electricity and Air Supply Safety Data Sheets (SDS) Safety Limits (LEL, TLV, OEL, MEL), Ventilation and Paint Application
* Identify coating Types and Systems * Use Products Data Sheets - Review * Use Products Data Sheets - Review * Identify Single and Two Part Materials and Paint Mixing * Identify Pot-Life and Induction * Check Storage, Batch Numbers, Coverage and Compatibility * Determine Volume Solids * Calculate Coverage * Understand the impotence of Relative Humidity, Dew Point, Steel
Temperature Drying and Recoating (inc, cure) * Use correct Brush Application * Apply Safety in Paint Applications * Use and identify Airless Spray (Introduction) and Air Assisted Spray
(Introduction) systems * Apply Wet Film and DryThickness
COURSE TOPICS:
* Health & Safety. * Coating types * Coating application
PRACTICAL: To enable maximum learning and benefit from this course, learners will carry out a practical exercise demonstrating use of PPE and RPE, the setup, operation, flushing and storage of airless spray equipment including relevant aspects of safety, efficiency, fault diagnosis and routine maintenance procedures under prescribed environmental conditions.
Highway Electrical Training Specification © HESA
Issue12.17 Page 70 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Excavate, backfill and reinstate COURSE REFERENCE: 301.1, 301.3, 301.4, 301.5, 301.6, 301.7, 301.8 / M303, M304,M305, M306,M308 This unit deals with excavation and reinstatement in the highway. At present, the above courses will be deemed to be satisfied by the appropriate NRSWA unit assessment as follows:
Course No. Course Title NRSWA Unit
301.1 / M303 Excavation in the highway 3
301.3 / M304 Reinstatement and compaction 4
301.4 / M305 Reinstatement of sub-base and base 5
301.5 / M306 Reinstatement of cold lay bit-mat 6
301.6 Reinstatement of hot lay bit-mat 7
301.7 / M308 Reinstatement of concrete slabs 8
301.8 Reinstatement of modular and concrete 9
Highway Electrical Training Specification © HESA
Issue12.17 Page 71 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Minor Excavation and temporary reinstatement in the highway for
column / post holes COURSE REFERENCE: 301.2 DURATION: 4 Hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working within the Highway Electrical Sector the underpinning skills required to carry out minor excavation such as for a column hole. This course is not suitable where more substantial or multiple excavations will be carried out, without suitable NRSWA accredited supervision, by the candidate in which case, course 301.1 should be used. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses.
OBJECTIVES: On completion of the course learners will:
* Identify different types of footway and carriageway. * Identify hazards, risks and control measures * Carry out minor excavation in the highway. * Correctly choose excavating materials for re-use as backfill.
COURSE TOPICS: * Footways and carriageways: construction layers. * Flexible and modular pavement. * Exposed apparatus. * Field identification of excavated materials.
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 72 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installing, maintaining and removing temporary traffic management
on rural and urban roads COURSE REFERENCE: 302.1 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course or in combination with 302.2 COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning knowledge required for the understanding and use of equipment for Safety at Street Works and Road Works, as appropriate to the scope of their work on site. It aims to cover Moving / Minor Works / Short duration and Single Vehicle works signing and guarding, and provides an awareness of other forms of signing and guarding.
It provides the underpinning knowledge to satisfy the training requirements of NHSS8 (as agreed with NHSS 12D) and does not confer NHSS12D registration on the Learner. In order to satisfy the current assessment requirements of NRSWA Unit 2 or Unit 10, additional modules are required PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. In addition learners should have their own copy of the “Red Book” – Safety at Street Works and Road Works – A Code of Practice – and have familiarised themselves with the contents. ASSESSMENT: Learners will be assessed throughout the course, using models and a summative assessment will complete the course.
OBJECTIVES: On completion of the course candidates will be able to use the principles and take actions required to correctly sign and guard road works to the “Safety at Street Works and Road Works Code of Practice”.
• Identify risk assessments and method statements
• Identify the relevant codes of practice and other associated documentation involved in traffic management
• State the main requirements for signing and guarding road works to national standards.
• Identify the equipment required in temporary traffic management
• State the requirements for signing and guarding of road works for mobile and short duration works
• Identify the different methods of positive traffic control
• State how to deal with pedestrians
• Identify the main steps for installing, maintaining and removing any positive traffic control systems.
COURSE TOPICS:
• An outline of the legislation, Codes of Practice, Risk Assessments, Method Statements.
• Highway Terminology, Site definitions, Safety Zones
• Types of work, Equipment & Vehicles, Traffic Lane widths
• Mobile and Minor Works Basic Layouts, Stop Works Sign, Give and Take, Priority Signing, Stop and Go
• Dealing with pedestrians. PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises, some using models. These may be both interactive and demonstrative to enhance the learning experience. They are identified at appropriate points in the trainer’s material. DOCUMENTATION: Manuals:
• Safety at Street Works and Road Works (The Code of practice)
• Chapter 8, TSRGD available for reference
Highway Electrical Training Specification © HESA
Issue12.17 Page 73 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installing, maintaining and removing positive traffic control including
temporary / portable traffic signal equipment on rural and urban roads
COURSE REFERENCE: 302.2 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course and combined with 302.1 COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning knowledge required for the understanding and use of equipment for Safety at Street Works and Road Works, as appropriate to the scope of their work on site. It aims to cover Moving / Minor Works / Short duration and Single Vehicle works signing and guarding, and provides an awareness of other forms of signing and guarding.
It provides the underpinning knowledge to satisfy the training requirements of NHSS8 (as agreed with NHSS 12D) and does not confer NHSS12D registration on the Learner. In order to satisfy the current assessment requirements of NRSWA Unit 2 or Unit 10, additional modules are require.
PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. In particular, learners must have attended and successfully completed course 302.1. In addition learners should have their own copy of the “Red Book” – Safety at Street Works and Road Works – A Code of Practice and the “Pink Book” – An Introduction to the use of portable Vehicular Signals – and have familiarised themselves with the contents. ASSESSMENT: Learners will be assessed through a summative assessment, which will be largely practical using actual equipment in a simulated environment. There should be available a sufficient quantity of good quality, working temporary/portable traffic signals, traffic signs and cones. OBJECTIVES: On completion of the course candidates will be able to use the principles and take actions required to correctly sign and guard road works to the “Safety at Street Works and Road Works Code of Practice”.
• Identify the correct sequence of actions for installing, maintaining and removing positive traffic control systems.
• Identify the layout for the traffic management control by two way temporary traffic signals
• Identify the correct sequence of actions for installing, maintaining and removing temporary traffic signals
• Carry out the installation, testing, operation and removal of a two way temporary traffic signal installation
COURSE TOPICS:
• Refresher of key points covered in course 302.1
• Temporary / portable traffic signals
• Dealing with pedestrians. PRACTICAL: To enable maximum learning and benefit from this course, there will a summative practical session. This will be interactive to enhance the learning experience. DOCUMENTATION: Manuals:
• Safety at Street Works and Road Works (The Code of practice)
• An Introduction to the use of VA Portable Traffic Signals (The Code of Practice)
• Chapter 8, TSRGD available for reference
Highway Electrical Training Specification © HESA
Issue12.17 Page 74 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installing, maintaining and removing temporary traffic management
on dual carriageways restricted to 40 mph or less COURSE REFERENCE: 302.3 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS TBA.
It provides the underpinning knowledge to satisfy the training requirements of NHSS8 (as agreed with NHSS 12D) and does not confer NHSS12D registration on the Learner. In order to satisfy the current assessment requirements of NRSWA Unit 2 or Unit 10, additional modules are require.
PREREQUISITES: TBA. ASSESSMENT: Learners will be assessed throughout the course, a summative assessment will complete the course.
OBJECTIVES: On completion of the course candidates will be able to use the principles and take actions required to correctly sign and guard road works to the “Safety at Street Works and Road Works Code of Practice”.
• TBA COURSE TOPICS:
• TBA
PRACTICAL: To enable maximum learning and benefit from this course, there will a summative practical session. This will be interactive to enhance the learning experience. DOCUMENTATION: Manuals:
• Safety at Street Works and Road Works (The Code of practice) • An Introduction to the use of VA Portable Traffic Signals (The Code of Practice)
• Chapter 8, TSRGD available for reference
Highway Electrical Training Specification © HESA
Issue12.17 Page 75 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Signing, Lighting and Guarding - Monitoring and Supervision (under
development) COURSE REFERENCE: 310 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector the underpinning knowledge required for the understanding, monitoring and supervision of equipment for Safety at Street Works and Road Works, as appropriate to the scope of their work on site. It provides the underpinning knowledge to satisfy the requirements of NHSS 12D, as particularised for the Highway Electrical Industry by the SS 8 Committee and the Standards and Training Group. In order to satisfy the assessment requirements of NRSWA Unit 10 additional modules may be required. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: Course Candidates will be assessed throughout the course and a summative assessment will complete the course. OBJECTIVES:
This course is currently under development. COURSE TOPICS:
This course is currently under development PRACTICAL: This course is currently under development DOCUMENTATION: Manuals:
• Safety at Street Works and Road Works (The Code of practice)
• An Introduction to the use of VA Portable Traffic Signals (The Code of Practice)
Highway Electrical Training Specification © HESA
Issue12.17 Page 76 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Monitoring Excavation in the Highway; Monitoring Reinstatement &
Compaction of Backfill Materials COURSE REFERENCE: 311 / M311; 312 / M312; 313 / M313; 314 / M314; 315 / M315; 316 /
M316
At present, the above courses will be deemed to be satisfied by the appropriate NRSWA unit assessment as follows:
Course No. Course Title NRSWA Unit
311 / M311 Monitoring Excavation in the Highway 11
312 / M312 Monitoring Reinstatement & Compaction of Backfill Materials
12
313 / M313 Monitoring reinstatement of sub-base 13
314 / M314 Monitoring reinstatement in bituminous material 14
315 / M315 Monitoring reinstatement in concrete slabs 15
316 / M316 Monitoring reinstatement in modular and concrete surfaces
16
Highway Electrical Training Specification © HESA
Issue12.17 Page 77 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Basic Electrical Theory COURSE REFERENCE: 401.1 DURATION: 14 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with the knowledge and key skills to facilitate the understanding of fundamental electrical principles, and the application within day-to-day activities. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* State how electricity works * Explain the difference between AC and DC circuits * Define current, voltage, resistance, power, common conductors
and common terms * State and use Ohms Law. * Define parallel and series circuits * State & use Power calculations * Identify a limited range of common electrical components and
their functions. * State typical earthing arrangements and bonding. * Read basic electrical circuit diagrams
COURSE TOPICS:
* Electrical Theory. * Electrical Components and functions * Circuit protection and basic discrimination * Transformers, Batteries * Earthing and Bonding. * Power Distribution Circuits. * Electrical Safety.
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 78 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Advanced Electrical Theory COURSE REFERENCE: 401.2 DURATION: 14 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with the knowledge and key skills to facilitate the understanding of advanced electrical principles, and the application within day-to-day activities. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Define Common terms
• Carry out Advanced Calculations
• Explain the concept of Inductance
• Identify three phase circuit diagrams
• Explain the operation of RCD’s, RCBO’s
• Explain the operation of PV Cells COURSE TOPICS:
• Recap on basic Electrical Theory.
• HV, LV, SELV, PELV, FELV
• Power Factor, PSCC, ELI, VD calculations
• Vector Diagrams Three Phase Circuits
• Harmonics
• RCD’s, RCBO’s
• Photovoltaic cells
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 79 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Electricity at Work Regulations COURSE REFERENCE: 402 DURATION: 4-hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with an understanding and awareness of the Electricity at Work Regulations, and their individual and collective responsibilities under the organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State the scope of the regulations
• State the requirements of the Regulations in respect to live working and competency
• State the main areas covered by the EAW Regs
• Identify the basic safety procedures necessary for the installation, maintenance, inspection and working practices used in electrical installations.
COURSE TOPICS:
• The Electricity at Work Regulations & Guidance
• Electric shock, fire, explosions and burns.
• Maintenance, inspection, isolation, normal dead and live working procedures.
• Applying the regulations to equipment located on the Highway.
• Suitability, protection, placing, integrity and security of conductors. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 80 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: BS 7671:2018 - IET Wiring Regulations COURSE REFERENCE: 403 DURATION: 14 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide employees working within the Highway Electrical Sector with a theoretical understanding of BS 7671 (IET Wiring Regulations) and associated requirements. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State the need for standards, regulations, testing and certification.
• Demonstrate knowledge of the scope and plan of the IET wiring regulations
• Identify where Highway Electrical installations are covered.
• Describe methods of protection available in highway electrical installations
• Identify where inspection and testing is covered COURSE TOPICS:
• Introduction to BS 7671.
• Requirements for standards, regulation, testing and certification.
• Fundamental Requirements for Safety as defined in BS 7671.
• Terminology, definitions and abbreviations.
• Theory and application of Earthing and Bonding.
• Safety and Protection of equipment and people.
• BS 7671 in respect to Highway Electrical street furniture PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 81 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Initial and Periodic Electrical Inspection and Testing (Traffic Control and Public Lighting)
COURSE REFERENCE: 712 DURATION: 28 hours* (Recommended Minimum Duration. * For combined Traffic and Public Lighting the course minimum is 28 hours) CERTIFICATION: Available individually for this course COURSE AIMS: This course aims to provide operatives with the knowledge and skills required for Initial and periodic electrical inspection and testing of new, existing or refurbished installations. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending this course. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative theoretical and practical assessment based on agreed criteria will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Define the purpose and difference of initial and periodic inspection and testing
• Use appropriate Test Equipment correctly and safely.
• Define the tests, test equipment and test methods.
• Carry out initial inspection and testing.
• Carry out periodic inspection and testing
• Complete an appropriate Certificate.
• Explain the reasons for an appropriate record system
• Identify appropriate action for unsatisfactory results.
• Record and report variations
COURSE TOPICS:
• Hazards and risks
• Initial and periodic testing of new, existing and replacement Highway electrical equipment.
• Test methods and working practices
• Using Electrical Test Equipment.
• Calculation of Earth Loop Impedance.
• Types of certificates used in Highway Electrical works PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience. The practical assessments will be carried out as identified by the HESA assessment criteria, on equipment that either accurately reflects ‘real site conditions’ or ‘using defined’ equipment that enables full coverage of the testing requirements.
Highway Electrical Training Specification © HESA
Issue12.17 Page 82 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Initial and Periodic Electrical Inspection and Testing (Communications and Traffic Control)
COURSE REFERENCE: 715 DURATION: 28 hours* (Recommended Minimum Duration. * For combined Communications and Traffic Control the course minimum is 28 hours) COURSE AIMS: This course aims to provide operatives with the knowledge and skills required for Initial and periodic electrical inspection and testing of new, existing or refurbished installations. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending this course. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative theoretical and practical assessment based on agreed criteria will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Define the purpose and difference of initial and periodic inspection and testing
• Use appropriate Test Equipment correctly and safely.
• Define the tests, test equipment and test methods.
• Carry out initial inspection and testing.
• Carry out periodic inspection and testing
• Complete an appropriate Certificate.
• Explain the reasons for an appropriate record system
• Identify appropriate action for unsatisfactory results.
• Record and report variations
COURSE TOPICS:
• Hazards and risks
• Initial and periodic testing of new, existing and replacement Highway electrical equipment.
• Test methods and working practices
• Using Electrical Test Equipment.
• Calculation of Earth Loop Impedance.
• Types of certificates used in Highway Electrical works PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience. The practical assessments will be carried out as identified by the HESA assessment criteria, on equipment that either accurately reflects ‘real site conditions’ or ‘using defined’ equipment that enables full coverage of the testing requirements.
Highway Electrical Training Specification © HESA
Issue12.17 Page 83 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Coordinate the work of others on Site COURSE REFERENCE: 801 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to familiarize employees working in the Highway Electrical industry with the essentials of coordinating the work of others on site PREREQUISITES: In order to gain maximum benefit and learning outcomes form this course the attendee needs to satisfy the required Pre-requisite Underpinning knowledge criteria ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• State the main areas of responsibility
• State the key characteristics of an effective coordinator of teams
• Define assertive behaviour
• Identify the steps in communication
• State the main areas of one of the main motivational models
• State the importance of leading by example COURSE TOPICS:
• Defining the role & responsibilities of a supervisor
• Assertiveness
• Communication
• Inter-personal relationships
• Motivation
• Legal aspects - equal opportunities etc. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 84 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Set teams to work and coordinate the work for Quality, Safety &
Productivity COURSE REFERENCE: 802 DURATION: 14 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to familiarize employees working in the Highway Electrical industry with the essentials for site coordination, with a key focus on Quality, Safety & Productivity PREREQUISITES: In order to gain maximum benefit and learning outcomes form this course the attendee needs to satisfy the required Pre-requisite Underpinning knowledge criteria and to have attended course 801 ASSESSMENT: A summative assessment will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Identify how to delegate effectively
• Explain a technique to manage personal time effectively
• Explain how to ensure teams work well together
• Explain how to address under-performance
• Explain the steps to take to ensure continuing satisfactory performance
• Explain a mechanism for individual and team development
• Identify key H&S, Environmental and other relevant legal aspects on site
COURSE TOPICS:
• Time management
• Delegation
• Managing the manager
• Team Building
• Motivation
• Coaching and mentoring
• Communication
• Health & Safety and Employment law aspects PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 85 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: CDM Regulations COURSE REFERENCE: 805 DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS This course aims to provide an overview of the CDM regulations, including the responsibilities of the duty holders at each stage of a project. It also aims to give an understanding of how implementation of these regulations impacts on the overall management and co-ordination of health, safety and welfare throughout all stages of a project, and the associated benefits in terms of the reduction of accidents and ill health. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State the purpose and benefits of the CDM regulations.
• State under what circumstances the CDM regulations apply.
• State the main stages of a project.
• State the main duty holders and their responsibilities at each stage, including specifically designers
• Describe how competency is assessed
• Describe the contents of the pre-tender stage H&S information.
• Describe the contents of the construction phase H&S plan.
• Describe the contents of the H&S file.
• Explain how the H&S file should be used after the project has been completed.
COURSE TOPICS:
• An Introduction to the CDM regulations.
• Application of the CDM regulations.
• The stages of a construction project.
• The main duty holders and their responsibilities.
• Competency assessment
• The pre-tender H&S information
• The construction phase H&S plan.
• The H&S file. PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 86 of 200 © Highway Electrical Skills Academy
Section 2 – Specialist Modules
Public Lighting & Illuminated Signs
Sectio
n 2
– P
ub
lic L
igh
ting
& Illu
min
ate
d S
ign
s
Highway Electrical Training Specification © HESA
Issue12.17 Page 87 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Lorry Mounted Crane Slinger / Signaller COURSE REFERENCE: 211 DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS: This course is specifically for operatives who assist in the installation of lighting columns and who act as a banksman to a driver or crane operator during loading, unloading and installation operations. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State the relevant legal requirements including examination, certification and responsibilities
• State the need for routine inspection, reporting and maintenance
• Assess different types of loads and centres of gravity.
• Assist a vehicle driver in manoeuvring on site by recognised signalling methods.
• Identify the range of lifting gear including methods of slinging.
• Assist in controlling loads. COURSE TOPICS:
• Reversing vehicles in confined spaces.
• Working on a live carriageway
• HSE and Road Transport Industry Training Board recommended code of signals
• HSE Guide Notes GS9 standard
• Handling Lighting columns 3m to 15m PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 88 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Use of Lorry Mounted Crane in the installation of structures
supporting highway electrical equipment COURSE REFERENCE: 212
DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees within the sector and who install lighting columns using lorry mounted cranes, with the skills and knowledge to erect columns safely and effectively. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State the relevant legal requirements including examination, certification and responsibilities.
• Differentiate between specific types of lorry mounted cranes.
• State the safety regulations and operating rules applicable to lorry mounted cranes.
• State the need for routine inspection, reporting and maintenance
• Assess different types of loads and centres of gravity.
• Explain the effect on Safe Working Loads at varying radii and adverse stability situations
• Manoeuvre on site assisted by a banksman using recognised signalling methods.
• Identify the range and use of lifting gear including methods of slinging.
• Assist in controlling loads. COURSE TOPICS:
• Reversing vehicles in confined spaces.
• Working on a live carriageway
• HSE and Road Transport Industry Training Board recommended code of signals
• HSE Guide Notes GS9 standard
• Erecting Lighting columns 5m to 15m PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 89 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Erect columns and brackets COURSE REFERENCE: 501 DURATION: 3 hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to erect columns in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses.
OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works
• Locate position of column marked by Engineer.
• Verify instructions for the size of hole to be dug.
• Explain the need for installing the bracket and lantern after column installation.
• Refer difficulties in excavating hole in marked position.
• Decide on appropriate method of lifting column.
• Install rooted columns correctly in hole.
• Correctly align and backfill.
• Compare various alternative bases.
• Prepare/obtain concrete used in accordance with specification.
• Prepare and fill concrete cast bases for equipment.
• Bolt equipment to prepared bases in accordance with specification. COURSE TOPICS:
• Hazards and risks
• On site precautions
• Lifting and handling of columns
• Evaluation of size of column holes for different circumstances.
• Pole and bracket types, handling storage and installation
• Foundations, rooted columns, baseplate units, special bases.
• Concrete mixes PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 90 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Remove columns and brackets COURSE REFERENCE: 502 DURATION: 2 Hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to remove columns in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works
• Locate column to be removed.
• Verify that electricity service has been removed.
• Explain the need for removing the bracket and lantern prior to column removal.
• Refer difficulties in removal of column.
• Select appropriate material for backfill
• Temporarily reinstate after completion of excavation works.
• Correctly dispose of redundant equipment. COURSE TOPICS:
• Hazards and risks
• On site precautions
• Pole and bracket types, handling storage and disposal.
• Variation reporting PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 91 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Re-align Rooted Columns COURSE REFERENCE: 503 DURATION: 1 Hour (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to realign columns in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works
• Locate column to be re-aligned.
• Refer difficulties in re-aligning column.
• Correctly re-align and reinstate surfaces.
• Prepare/obtain concrete used in accordance with specification. COURSE TOPICS:
• Hazards and risks
• On site precautions
• Pole and bracket types, handling storage and installation.
• Foundations for rooted columns.
• Concrete mixes.
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 92 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Feeder Pillars COURSE REFERENCE: 504 DURATION: 1 Hour (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to install feeder pillars in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Identify necessary precautions before during and after completion of works
• Locate position of cabinet marked by Engineer.
• Identify manufacturer’s instructions for the size of excavation to be dug.
• Refer difficulties in excavating hole in marked position.
• Install cabinet in accordance with manufacturer’s instructions correctly in hole.
• Correctly align and backfill.
• Prepare/obtain concrete used in accordance with specification.
• Prepare and fill concrete cast bases for equipment.
• Bolt equipment to prepared bases in accordance with specification. COURSE TOPICS
• Hazards and risks
• On site precautions
• Cabinet types, handling storage and installation
• Foundations for cabinets.
• Concrete mixes
• Variation reporting PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 93 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Base-Lit Bollards COURSE REFERENCE: 505 DURATION: 4 Hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to install base-lit bollards in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Identify necessary precautions before during and after completion of works
• Locate position of bollard marked by Engineer.
• Identify manufacturer’s instructions for the size of excavation to be dug.
• Refer difficulties in excavating hole in marked position.
• Install bollard in accordance with manufacturer’s instructions correctly in hole.
• Correctly align and backfill.
• Prepare/obtain concrete used in accordance with specification.
• Prepare and fill concrete cast bases for equipment.
• Bolt equipment to prepared bases in accordance with specification. COURSE TOPICS
• Hazards and risks
• On site precautions
• Bollard types, handling storage and installation
• Foundations for bollards
• Concrete mixes
• Variation reporting PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 94 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Base-Lit Bollards COURSE REFERENCE: 508 DURATION: 4 Hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to install base-lit bollards in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses.
OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works
• Install bollard on to base in accordance with manufacturer’s instructions.
• Correctly orientate and secure.
• Explain why a person who is fully trained and authorised in testing and connection should only connect the bollard to the cut-out.
• Report variations.
COURSE TOPICS:
• Hazards and risks.
• On site precautions
• Bollard types and installation
• Variation reporting
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 95 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of lantern and bracket COURSE REFERENCE: 506 DURATION: 3 Hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to install lanterns and brackets in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works
• Wire lanterns and fit onto brackets*.
• Install brackets/lantern assembly on to columns.
• Demonstrate avoidance of damage to cables.
• Correctly line up and secure equipment as placed.
• Secure sign plates to posts.
• Install control gear and wiring but not connect into cut-out*.
• Report variations (* These objectives are not applicable for traffic signs – non-electrical works)
COURSE TOPICS:
• Hazards and risks.
• On site precautions
• Lantern and bracket types and installation
• Variation reporting
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 96 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation and wiring of control gear COURSE REFERENCE: 507 DURATION: 4 Hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to install and wire control gear in a safe and competent manner, where this equipment is not integral to the lantern. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works
• Select correct circuit diagram.
• Select appropriate cables.
• Install control gear securely.
• Ensure cables are correctly stripped back and terminated in gear.
• Ensure wiring was in accordance with circuit diagram.
• Ensure wiring avoids obstructing access to gear and is neatly laid out.
• Use heat resistance sleeving as specified.
• Ensure lamp operates correctly.
• Test operation of photoelectric cell.
COURSE TOPICS:
• Circuit diagrams: various types of lamps, different photo cells, lighting column/bollard/beacon circuits.
• Correct installation: neat, operates correctly, secure terminations, and secure control gear.
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 97 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Install underground cables COURSE REFERENCE: 509 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to install underground cables in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works
• Evaluate the purpose and need for different underground cable systems.
• Evaluate the purpose and need for cable marker tape and ducts.
• Identify different types of cables.
• Identify appropriate excavation procedure.
• Carry out excavation of trench in accordance with recognised safe working practices to the correct depth.
• Prepare base of trench for cable laying or ducting as appropriate..
• Install underground cables and be aware of safe working practices.
• Backfill and reinstate trench in accordance with specification.
• Report variations. COURSE TOPICS:
• Hazards and risks.
• On site precautions.
• Cable types and installation.
• Variation reporting.
• Identification of REC, loop supply, private cable networks.
• Regulations and Codes of Practice PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 98 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Termination and connection of underground cables into supply
cut-outs COURSE REFERENCE: 510 DURATION: 3 hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This unit is about ensuring the safe and correct techniques for the termination and connection of underground cables into supply cut-outs to non-energised termination points. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses.
OBJECTIVES: On completion of the course learners will:
• Apply appropriate health and safety measures to safeguard workers and the public.
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works.
• Identify different types of cables and their individual termination requirements.
• Trim and prepare cables and fit cable glands or other termination fittings.
• Take appropriate precautions to ensure safe connection into cut out.
COURSE TOPICS:
• Hazards and risks.
• On site precautions.
• Cable types.
• Cable preparation and termination
• Variation reporting.
• Cut out types.
• Terminations: middle fuse/single units, RCD’s, glands. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises, specifically cable preparation and termination of 16mm2 looped cables. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 99 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Jointing of cables COURSE REFERENCE: 511 DURATION: 4.5 hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This unit is about ensuring the safe and correct techniques for the termination and jointing of cables. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Apply appropriate health and safety measures to safeguard workers and the public.
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works.
• Identify different types of cables and their individual jointing requirements.
• Prepare cable to accommodate cable joint.
• Identify cores to be jointed and prepare.
• Use appropriate tools for jointing.
• Ensure continuity of all conductors.
• Ensure correct colour coding of cores and sleeve as appropriate.
• Enclose joint and fill with compound.
COURSE TOPICS:
• Hazards and risks.
• On site precautions.
• Cable types.
• Joint types.
• Variation reporting.
• Overview on continuity PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises, specifically a minimum of 16mm2 or 25mm2 to 6mm2 dry tee joint or use of a breech joint. These may be both interactive and demonstrative to enhance the learning experience.”
Highway Electrical Training Specification © HESA
Issue12.17 Page 100 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Night time monitoring COURSE REFERENCE: 601 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide operatives with the knowledge and skills required for the night time monitoring of public lighting installations. The need for rigorous inspections and accurate records is emphasised. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify hazards and risks * Take necessary precautions before, during and after completion of
works * State the purpose of night time inspections and identify different
inspection regimes. * Follow an inspection route. * Take into consideration the late striking of units when planning an
inspection route. * List types of defects and understand how to correctly identify them. * Identify the resources and plant requirements for night time
inspections. * Identify different methods for recording defects. * Record and report defects in an approved and timely manner.
COURSE TOPICS: * Hazards and risks * On site precaution * Requirements of night time inspections including the following:-
* Frequency of inspection. * Defects to be identified * Plan route and inspection cycle. * Effect of weather conditions.
* Recording and reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 101 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Operating, raising and lowering columns (Named) COURSE REFERENCE: 608 DURATION: 4 Hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide operatives working in the Public Lighting sector the knowledge and skills required to operate raising and lowering columns. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify hazards and risks * Take necessary precautions before, during and after completion of
works * Identify the types of raising and lowering columns. * Lower and raise column. * Explain why the column should be lowered before commencement of
any work. * Report variations and defects.
COURSE TOPICS:
* Hazards and risks * On site precautions * Types of raising and lowering columns and their uses
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 102 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Routine general maintenance COURSE REFERENCE: 603 DURATION: 2 hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide employees working in the Public Lighting sector the knowledge and skills required to carry out basic general maintenance. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify hazards and risks * Take necessary precautions before, during and after completion of
works * Identify different types of columns and lanterns and methods of entry * Carry out cleaning of luminaires and column base compartments * Recognise mechanical components that require lubrication * Identify items that need reporting
COURSE TOPICS:
* Hazards and risks * On site precautions * Lantern, column, sign and bollard types * The need for regular maintenance
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 103 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Visual inspection optical structural and electrical COURSE REFERENCE: 604 DURATION: 2 hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide operatives with the knowledge and skills required for the identification of wear and tear in a public lighting system and the limits for safety. The need for rigorous inspections and accurate records is emphasised.
PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses.
OBJECTIVES: On completion of the course learners will:
• Identify hazards and risks
• Take necessary precautions before, during and after completion of works
• Identify items to be inspected.
• Carry out optical mechanical and electrical inspections.
• Identify the differences between inspections and tests.
• Record results of inspection and record variations. COURSE TOPICS:
• Hazards and risks
• On site precaution
• Types of columns and lanterns.
• Assessing the structural integrity of columns by visual inspection
• Assessing the optical integrity of lanterns by visual inspection.
• Assessing the electrical integrity of public lighting installations by visual inspection
• Recording and reporting inspections. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 104 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Remove and replace components COURSE REFERENCE: 605 DURATION: 2 hours (Recommended Minimum Duration when courses amalgamated for certification) COURSE AIMS: This course aims to provide employees working in the Public Lighting sector the knowledge and skills required to remove and replace like for like components which have been identified as requiring replacement, during a routine maintenance visit. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and risks
• Identify necessary precautions before, during and after completion of works
• Isolate the supply before carrying out work
• Identify the requirements for replacing like for like components
• Replace components
• Test for correct operation
• Identify items that need reporting
• State how to dispose of redundant equipment and components in a safe and approved manner.
• Identify how to use tools and equipment in a safe and correct manner COURSE TOPICS:
• Hazards and risks
• On site precautions
• Lamp replacement strategies
• Mechanical and electrical components used in public lighting
• Correct handling and disposal of components PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 105 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Familiarisation of circuits used in public lighting COURSE REFERENCE: 404 DURATION: 2 hours (Recommended Minimum Duration when courses amalgamated for certification)
COURSE AIMS: This course aims to provide employees working within the Highway Electrical Sector with an understanding of the different types of circuits and circuit components used in public lighting applications PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify electrical components used in street lighting & traffic signs * Identify the difference between wiring in head and remote gear units. * Recognise wiring systems for illuminated signs, bollards and beacons. * Compare various circuits for photocells. * Identify cable layouts for private loop supplies. * Identify options for connecting circuits into supply cut outs. * Show correct fusing arrangements. * Identify the key references to BS 7671.
COURSE TOPICS:
* Wiring systems: remote/gear 'in head' lanterns. 1/2 part PEC control, single/double arm column, bollards, beacons, remote switching.
* Private loop supplies: feeder pillar/lighting column points of supply, terminations, loop in/out cable joints.
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 106 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Identify and replace faulty components COURSE REFERENCE: 606 DURATION: 6 hours COURSE AIMS: This course aims to provide operatives with the knowledge and skills required to identify and replace faulty components in highway lighting equipment. Emphasis is placed on the safe identification and replacement of faulty components using safe and approved methods. It does not include the diagnosis of faults on electrical systems. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify faulty lamp, control gear and similar components.
• Safely isolate the supply and replace equipment identified as most likely being faulty or at end of life.
• Check switching devices and equipment for correct operation.
• Leave equipment in normal operating mode.
• Record details of work carried out and report variations.
• Dispose of redundant equipment and components in a safe and approved manner
COURSE TOPICS: * Hazards and risks. * On site precaution. * Fault recording and reporting. * Types of fault on components and how to recognise them. * Systematic method of fault identification
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 107 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Diagnose and repair faults on electrical systems and equipment COURSE REFERENCE: 701 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide operatives with the knowledge and skills required to diagnose faulty highway electrical systems and the subsequent repair to the electrical system. Particular emphasis is placed on the use of safe and approved methods for diagnosing and correcting faults. This unit covers the testing of live equipment. Note fault diagnosis on underground cables is covered in course 705. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify necessary precautions before, during and after completion of works
* Make appropriate checks to identify the nature and location of faults. * Check electrical supply for polarity and possible faults on the supply
organisation equipment. * Measure voltages and currents on the electrical supply and at the lamp
terminals. * Identify faulty lamp, control gear, switching devices and similar
components. * Isolate installation before replacing components. * Replace faulty equipment correctly, securely and safely. * Adhere to all safety precautions when isolating/handling ECS cut-outs. * Record details of work carried out and report variations. * Dispose of redundant equipment and components in a safe and
approved manner. COURSE TOPICS:
* Hazards and risks * On site precaution * Fault recording and reporting * Types of faults and how to recognise them. * Systematic method of fault identification – circuit live.
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 108 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Emergency work COURSE REFERENCE: 702 DURATION: 4 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide operatives working in the Highway Electrical sector with the knowledge and skills required to complete the full range of emergency work that maybe required and assess the requirements for calling out the regional electricity organisation. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify hazards and risks * Take necessary precautions before, during and after completion of
works * Understand the need for attendance as soon as possible * Assess the emergency and carry out any work to make the site safe
except for any work on the regional electricity organisation equipment. * Decide on the need or otherwise to report to supervisor for advice and
instructions. * Decide on the need or otherwise to call out the regional electricity
organisation. * Make the site safe to prevent access by the general public. * Report actions and additional work required.
COURSE TOPICS:
* Hazards and risks * On site precautions * Communication of technical information * Assessment of site conditions under emergency situations
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 109 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Locate faults on underground cables COURSE REFERENCE: 705 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide operatives with the knowledge and skills required to locate a fault on underground cables used in highway electrical installations and subsequent repair. Particular emphasis is placed on the use of safe and approved methods. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify hazards and risks * Take necessary precautions before, during and after completion of
works * Identify and use different types of test equipment available. * Explain the different types of circuits used in underground cable
systems. * Carry out safe and systematic method for locating faults. * Replace faulty section of cable using approved methods. * Leave equipment in normal operating mode. * Record details of work carried out and report variations
COURSE TOPICS: * Hazards and risks * On site precaution * Types of test equipment. * Types of underground faults * Systematic method of fault identification.
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 110 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Periodic Structural Inspection and Testing COURSE REFERENCE: 706 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working within the highway electrical industry with the knowledge and skills required to carry out periodic structural testing on site PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify hazards and risks * Take necessary precautions before, during and after completion of
works * Identify the need for and types of structural testing * Identify the types and use of structural test equipment. * Identify the factors which could affect the results * Carry out safe and systematic method for carrying out structural testing * Record details of work carried out and report variations
COURSE TOPICS: * Hazards and risks * On site precaution * Types of tests * Types of test equipment * Methods for carrying out tests and factors affecting the results * ILE Report No. 22 – Lighting Columns and Sign Posts Planned
Inspection Routine PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 111 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Highway Lighting Photometric Performance Testing COURSE REFERENCE: 707 MDURATION: 4 hrs (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working within the highway electrical industry with the knowledge and skills required to carry out limited photometric testing of highway lighting installations on site PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Identify hazards and risks * Take necessary precautions before, during and after completion of
works * Identify the need for and types of photometric testing * Identify the types and use of photometric test equipment. * Identify the factors which could affect the results * Carry out safe and systematic method for carrying out photometric
testing * Record details of work carried out and report variations
COURSE TOPICS: * Hazards and risks * On site precaution * Types of tests * Types of test equipment * Methods for carrying out tests and factors affecting the results
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 112 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Maintain high mast lighting COURSE REFERENCE: 708 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide operatives with the knowledge and skills required to identify and replace faulty components used in high mast equipment. Emphasis is placed on the safe identification and replacement of faulty components using safe and approved methods. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
* Take necessary precautions before, during and after completion of works
* Identify the specialist tools and equipment required * State the safety requirements for winching and associated tools * State the requirements for lowering and raising the headframe * Identify correct luminaire alignment; faulty components. * Check operation and alignment of equipment. * Replace equipment identified as probably being faulty or at end of life. * Leave equipment in normal operating mode. * Record details of work carried out and report variations. * Dispose of redundant equipment and components in a safe and
approved manner. * State the key principle requirements for high mast installation
COURSE TOPICS: * Hazards and risks. * On site precaution * High mast purpose & construction * High mast maintenance operating procedures * Fault recording and reporting.
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 113 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Install High Mast Lighting (Specialist Training) COURSE REFERENCE: 709 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working in the highway electrical sector with the knowledge and skills required to erect and fit-out high mast columns in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses.
OBJECTIVES: On completion of the course learners will:
* Identify hazards and reduce risks. * Take necessary precautions before during and after completion of works * Locate position and orientation of high mast column * Work in a team to correctly assemble the high mast column * Explain the need for planning and specialist equipment to erect the column * Bolt equipment to prepared bases in accordance with specification, including
checking levelling. * Work in a team to correctly fix and wire the headframe * Fix, align and carry out functional testing on luminaires and control gear * Raise headframe and check correct operation
COURSE TOPICS:
* Hazards and risks * On site precautions * Assembly of mast sections * Lifting and handling of columns, including levelling, correct tightening and
protection of fixing down bolts / nuts * Assembly of headframe * Fixing and wiring of luminaires, including correct orientation * Operation of headframe
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 114 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Awareness of inspection & testing for witnessing purposes COURSE REFERENCE: 710 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working within the highway electrical industry with the knowledge and skills required to understand and witness the testing and inspection of new or refurbished highway electrical installations.
PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Demonstrate the concepts of earthing, bonding and insulation as described in the regulations.
• Define the purpose and difference of initial and periodic inspection and testing
• Identify appropriate Test Equipment correctly and safely.
• List the tests, test equipment and test methods.
• State the key items in an appropriate and recognised Certificate.
• Explain the reasons for an appropriate record system.
• State typical acceptable test results
• Identify appropriate action for unsatisfactory results.
• Record and report variations
COURSE TOPICS:
• Hazards and risks
• Electrical testing of new and replacement public lighting installations.
• Test methods and working practices
• Electrical Test Equipment.
• Calculation of Earth Loop Impedance.
• Types of certificates used in public lighting
• BS7671 and guidance PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 115 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Fundamental Inspection and Testing for the Addition or Alteration to an Installation
COURSE REFERENCE: 717 DURATION: 21 hours (Recommended Minimum Duration) COURSE AIMS: This course aims to provide employees working within the highway electrical industry with the knowledge and skills required to complete an initial inspection and testing on a single-phase installation for the addition and alteration to an installation that does not extend to the provision of a new circuit. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending, including mandatory 403 course. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Understand the scope of the work they are undertaking • Understand the relevant statutory and non-statutory requirements • State the information required to carry out inspection and testing • Complete the required Minor Electrical Installation Works certificate , • Understand the requirements for the Schedule of Inspections • State the human senses that may need to be employed during an initial verification • Select the appropriate items that are to be checked during the inspection • Understand the requirements of the EAWR for safe inspection and testing in terms of public and
users of the installation. • Understand Ingress Protection (IP) codes of equipment • Understand the types of instruments used for testing • Apply the sequence of tests and the reason for the sequence • State the tests for protective conductors and the relationship between conductor length, cross
sectional area, resistance and temperature • State the testing for completion of insulation resistance testing and associated precautions and
external influences • State the reasons for confirming correct polarity and the methods of testing used • State the reasons for earth fault loop impedance and describe methods for determining EFLI
including by enquiry, calculation and direct measurement • State the reasons for prospective fault current and describe methods for determination including by
enquiry or direct measurement • State the reasons for RCD testing and the method of application
COURSE TOPICS:
• Hazards and risks • Statutory Requirements • Test Equipment and test for use during Additions and Alternations to an Electrical Installation • Test methods and working practices • Recording and interpreting the results in line with BS7671 and limitations on work
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 116 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Initial and Periodic Electrical Inspection and Testing (Public Lighting) COURSE REFERENCE: 714 DURATION: 21 hours* (Recommended Minimum Duration. * For combined Traffic and Public Lighting the course minimum is 28 hours) COURSE AIMS: This course aims to provide operatives with the knowledge and skills required for Initial and periodic electrical inspection and testing of new, existing or refurbished installations. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending this course. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative theoretical and practical assessment based on agreed criteria will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Define the purpose and difference of initial and periodic inspection and testing
• Use appropriate Test Equipment correctly and safely.
• Define the tests, test equipment and test methods.
• Carry out initial inspection and testing.
• Carry out periodic inspection and testing
• Complete an appropriate Certificate.
• Explain the reasons for an appropriate record system
• Identify appropriate action for unsatisfactory results.
• Record and report variations
COURSE TOPICS:
• Hazards and risks
• Initial and periodic testing of new, existing and replacement Highway electrical equipment.
• Test methods and working practices
• Using Electrical Test Equipment.
• Calculation of Earth Loop Impedance.
• Types of certificates used in Highway Electrical works PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience. The practical assessments will be carried out as identified by the HESA assessment criteria, on equipment that either accurately reflects ‘real site conditions’ or ‘using defined’ equipment that enables full coverage of the testing requirements.
Highway Electrical Training Specification © HESA
Issue12.17 Page 117 of 200 © Highway Electrical Skills Academy
Section 3 – Specialist Modules
Traffic Signs (non–electrical)
additional to Modules in Section 2
Sectio
n 3
– T
raffic
Sig
ns
(no
n–
ele
ctric
al)
Highway Electrical Training Specification © HESA
Issue12.17 Page 118 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Excavate and Install in Embankments COURSE REFERENCE: S301.7 DURATION: 14 hours (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working in the sector with the knowledge and skills required to excavate and place concrete in large sign foundations in sloping terrain in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works.
• Verify instructions for the size, shape and orientation of foundation to be dug.
• Refer difficulties in excavating foundation in marked position.
• Compare various alternative bases.
• Prepare and correctly install appropriate post sockets/sleeves/cradles.
• Prepare/obtain and place concrete in accordance with specification.
COURSE TOPICS:
• Hazards, risks & on site precautions.
• Variation reporting.
• Deep excavations.
• Evaluation of different types of foundation for different circumstances.
• Special considerations for night working.
• Concrete mixes & placing of concrete.
• Backfilling and disposal of arisings.
PRACTICAL: To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 119 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Erect columns and posts over 140mm diameter in multi-post
foundations
COURSE REFERENCE: S501 DURATION: 35 hrs (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working in the sector with the knowledge and skills required to erect columns, posts or masts forming in a safe and competent manner.
PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents.
ASSESSMENT: A summative assessment will follow the completion of this course or group of courses.
OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion of works.
• Locate position of column/post marked by Engineer.
• Verify instructions for the size of hole to be dug & identify who to refer difficulties to.
• Compare various alternative bases.
• Prepare and correctly install appropriate post sockets/sleeves/cradles.
• Decide on appropriate method of transporting/lifting columns/posts.
• Install columns/posts correctly in foundation including alignment & backfill.
• Prepare/obtain and place concrete in accordance with specification.
• Prepare and fill concrete cast bases for bolt-down equipment such as cantilevers.
• Bolt equipment to prepared bases in accordance with specification. COURSE TOPICS:
• Hazards, risks & on site precautions.
• Post types, transport, handling, storage and installation
• Evaluation and size of column/post foundations for different circumstances.
• Foundations, baseplate units, special bases
• Excavation with machine.
• Concrete mixes & placing of concrete.
• Special considerations for night working.
• Types of slings and fixings.
• Backfilling and disposal of arisings.
• Variation reporting.
• TA 89/05 PRACTICAL: To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 120 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation / removal of sign face up to 3sqm COURSE REFERENCE: S512.1 DURATION: 4 hours (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to erect road traffic signs and luminaires in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion or works.
• Load, transport sign plates to site and offload.
• Correctly align and secure sign plates, stub arms and lanterns to posts.
• Take down sign plates from posts, load and transport off site.
• Report variations. COURSE TOPICS:
• Hazards and risks.
• On site precautions.
• Traffic sign types, handling and installation.
• Lantern types and configuration, handling and installation.
• Working at height.
• Variation reporting.
• Visual inspection. PRACTICAL: To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 121 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation / removal of sign face over 3sqm but not exceeding 15
sq.m COURSE REFERENCE: S512.2 DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to erect road traffic signs in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion or works.
• Load, transport sign plates to site and offload.
• Correctly align and secure sign plates to posts.
• Take down sign plates from posts, load and transport off site.
• Report variations. COURSE TOPICS:
• Hazards and risks (including weather).
• On site precautions.
• Special considerations for overhead working.
• Special considerations for night working.
• Traffic Sign types, handling and installation.
• Types of slings and fixings.
• Working at height.
• Joining channel sections.
• Variation reporting.
• Visual inspection. PRACTICAL: To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 122 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation / removal of sign face over 15 sq. m COURSE REFERENCE: S512.3 DURATION: 11 hours (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to erect road traffic signs in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion or works.
• Load, transport sign plates to site and offload.
• Correctly align and secure sign plates to posts.
• Take down sign plates from posts, load and transport off site.
• Report variations. COURSE TOPICS:
• Hazards and risks (including weather).
• On site precautions.
• Special considerations for night working.
• Traffic Sign types, handling and installation.
• Types of slings and fixings.
• Working at height.
• Joining channel sections.
• Variation reporting.
• Visual inspection. PRACTICAL: To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 123 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation / removal of signs on gantries or overhead structures COURSE REFERENCE: S513 DURATION: 14 hours (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working in the sector the knowledge and skills required to erect road traffic signs on overhead structures in a safe and competent manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and reduce risks.
• Take necessary precautions before during and after completion or works.
• Load, transport sign plates to site and offload.
• Correctly align and secure sign plates to gantry uprights/structures.
• Take down sign plates from gantry uprights/structures, load and transport off site.
• Report variations. COURSE TOPICS:
• Hazards and risks (including weather).
• On site precautions.
• Special considerations for overhead working.
• Special considerations for night working.
• Traffic Sign types, handling and installation.
• Types of slings and fixings.
• Working at height.
• Joining channel sections.
• Variation reporting.
• Visual inspection. PRACTICAL: To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 124 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Traffic Sign Photometric Performance Testing COURSE REFERENCE: S707 DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS: This course aims to provide employees working within the highway electrical industry with the knowledge and skills required to carry out visual inspection and photometric testing of road traffic sign assemblies on site. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify hazards and risks.
• Take necessary precautions before, during and after completion of works.
• Visually inspect sign plates, fixings and posts.
• Identify the need for and types of photometric testing.
• Identify the types and use of photometric test equipment.
• Identify the factors which could affect the results.
• Carry out safe and systematic method for carrying out photometric testing.
• Record details of work carried out and report variations.
COURSE TOPICS:
• Overview of maintenance Code of Practice
• Hazards and risks.
• On site precautions.
• Visual inspection and assessment.
• Types of tests.
• Types of test equipment.
• Methods for carrying out tests and factors affecting the results.
• Recording test results. PRACTICAL: To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 125 of 200 © Highway Electrical Skills Academy
Section 4 – Specialist Modules
Slot Cutting
Sectio
n 4
– S
lot C
uttin
g
Highway Electrical Training Specification © HESA
Issue12.17 Page 126 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Cut Slot to Specification COURSE REFERENCE: TSC001 DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to cut slots to specification PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after cutting the slot(s)
• State different slot configurations
• Work to customer specification / manufacturers instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks, including abrasive wheels, traffic, blowers, water
• Environmental considerations
• Onsite precautions.
• Cable / Loop types
• Variation reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 127 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Lay Cable and Seal COURSE REFERENCE: TSC002 DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to install a combination of cable types. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after installing equipment.
• Identify cable types.
• Install different types of cables.
• Identify mechanism(s) for sealing slots
• Work to customer specification / manufacturers instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks, including traffic, blower, boiler, hot working, resin, pitch.
• Environmental considerations
• Onsite precautions.
• Cable types and installation.
• Cable preparation
• Sealing of slot
• Variation reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 128 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Repair Faulty Cable COURSE REFERENCE: TSC003 DURATION: 7 hours (Recommended Minimum Duration) COURSE AIMS This course is designed to provide the attendees with the principles necessary to facilitate the fundamental common concepts associated with the understanding of Cable Maintenance in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before and during maintenance activities.
• Maintain different types of cables.
• Identify cable types.
• Work to required specifications
• Test cable to required specifications
• Report actions and unsafe sites to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cable types and maintenance.
• Signal, Supply Power.
• Testing Methods.
• Action reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 129 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Access to cabinets through ducts etc. COURSE REFERENCE: TSC004 DURATION: 7 hours (Recommended Minimum Duration)
COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to access cabinets safely and to identify the particular hazards associated with this operation. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and Risks.
• Take necessary precautions before, during and after installing equipment.
• Identify cable types.
• Identify cabinet types and means of access
• Install different types of cables, excluding connections.
• Work to client specifications / manufacturers instructions including reinstatement of base seal.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks – including site specific risk assessments and separate written justification where appropriate, base seal
• Onsite precautions.
• Cable types and installation.
• Cabinet types and means of access
• Variation reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 130 of 200 © Highway Electrical Skills Academy
Section 5 – Specialist Modules
Highway Electronic Installation of Infrastructure
Equipment
Sectio
n 5
– H
igh
way
Ele
ctro
nic
Insta
llatio
n o
f
Infra
stru
ctu
re E
qu
ipm
en
t
Highway Electrical Training Specification © HESA
Issue12.17 Page 131 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Supporting Structures (Sector / Equipment name) COURSE REFERENCE: TIE001 DURATION: 10 hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to install a combination of supporting structures in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Identify necessary precautions before, during and after planting equipment
• Install different types of support structures associated with highway electronic installations.
• Identify precautions when preparing concrete bases
• Align support structures in accordance with client specification / manufacturing instructions.
• Report variations to site build to relevant personnel. COURSE TOPICS:
• Hazards and Risks including use of plant, lifting operations
• Onsite precautions.
• Supporting structures – e.g. Pole types
• Concrete bases and mixes.
• Bracket types
• Supporting structure and equipment alignment.
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 132 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Cabinets (Sector / Equipment Type) COURSE REFERENCE: TIE002 DURATION: 4-hours (Recommended Minimum Duration) COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to install Cabinets in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify associated Hazards.
• Identify necessary precautions before, during and after planting equipment.
• Identify appropriate fixing method
• Install Cabinet
• Check alignment and positioning
• Identify precautions and prepare concrete.
• Backfill and seal to client specification / manufacturing instructions.
• Report variations to site build to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Root installation
• Cabinet installation.
• Cabinet alignment.
• Concrete bases and mixes and sealants.
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 133 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Standard Detection (Sector / Equipment type) COURSE REFERENCE: TIE003 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to install a combination of Detection equipment, such as Loop, Optical, Infrared, Microwave and Pedestrian detection equipment. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Identify necessary precautions before, during and after installing equipment.
• Install different types of detection equipment.
• Install detection equipment types to client specification / manufacturers instructions
• Identify various detection types.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Detection types and installation.
• Detector alignment.
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 134 of 200 © Highway Electrical Skills Academy
Section 6 – Specialist Modules
Traffic Signals
Sectio
n 6
– T
raffic
Sig
nals
Highway Electrical Training Specification © HESA
Issue12.17 Page 135 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Traffic Signal Manual Panel Operations COURSE REFERENCE: M201 DURATION: 4 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide approved persons with the skills and knowledge to operate and select suitable and defined modes of traffic controller operation in a safe manner. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course Learner are required to have a basic understanding for need to carry out a site risk assessment. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State Safety Considerations for site junctions
• Explain Basic Controller Operation in terms of Traffic Staging
• Relate Stage Diagram Traffic Flows to actual Junctions
• State the basic manual panel functions
• Explain Traffic Control Safe Mode Switching methods
• Explain the requirements to return to Normal Junction Control COURSE TOPICS:
• Overview of safety considerations
• The Traffic Controller Stage and Phase relationships in terms of Traffic Stage Movements
• Site to Scale drawing interpretations to actual road junction
• The Manual Panel Operations
• Using the Manual Panel for controlling traffic flows
• Returning to local or computer control PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 136 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Traffic Principles COURSE REFERENCE: M301 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide employees working within the Traffic Sector with basic underpinning knowledge for basic traffic control principles which incorporate interpretation of site drawings. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State and relate to basic traffic terminology.
• Explain traffic and pedestrian controller applications and modes.
• Explain the basic principles and facilities associated with controller specification sheets.
• Explain basic controller communications using a rage of equipment
• Identify and read site plans. COURSE TOPICS:
• A general introduction to traffic signals
• The traffic STS symbols/plans.
• Basic Concepts:-Phases, Stages, Streams
• Basic timing periods:- Min, Max, Extensions, Intergreens, Detection
• Detection – an overview
• Junction and Pedestrian Controller Types and Modes:-, Traffic, Toucan, Pedestrian, Puffin, VA, FT, Manual
• The Basic Specification data sheets interpretation with connections, stages, phases streams and general information.
• Use of the handset/terminals for checking controller operation and facilities.
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 137 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Poles, Lanterns and Brackets COURSE REFERENCE: M501 DURATION: 10 hours (Recommended Minimum Duration) CERTIFICATION: M501 and M502 combined COURSE AIMS This course aims to provide suitably qualified Installation Operatives with the knowledge and practical key skills required to install a combination of Poles, brackets and Lantern types in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after planting equipment
• Install different types of poles associated with traffic installations.
• Identify precautions when preparing concrete bases
• Install different types of lanterns associated with traffic installations.
• Align aspect lanterns in accordance with manufacturing instructions.
• Install and assemble Brackets and extension arms.
• Report variations to site build to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Pole and Lantern Types and installation.
• LED systems
• Concrete bases and mixes.
• Pole and Aspect alignment.
• Other Pole furniture.
• Bracket types.
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 138 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Installation of Cabinets and Roots COURSE REFERENCE: M502 DURATION: 4-hours (Recommended Minimum Duration) CERTIFICATION: M501 and M502 combined COURSE AIMS This course aims to provide suitably qualified Installation Operatives with the knowledge and practical key skills required to install a Cabinet types in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify associated Hazards.
• Take necessary precautions before, during and after planting equipment.
• Install Cabinet Stools and housings.
• Identify precautions and correctly prepare concrete.
• Backfill and base seal to manufacturing instructions.
• Check alignment and positioning.
• Report variations to site build to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cabinet installation.
• Concrete bases and mixes and sealants.
• Cabinet alignment.
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 139 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Standard Detection COURSE REFERENCE: M503 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: M501, M503, M504 and M505 combined COURSE AIMS This course aims to provide suitably qualified Installation Operatives with the knowledge and practical key skills required to install a combination of Detection equipment, including Loop, Optical, Infrared, Microwave and Pedestrian detection equipment. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after installing equipment.
• Install different types of detection equipment.
• Cable and connect detection equipment types correctly.
• Identify various detection types.
• Work to manufacturer’s instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cabinet installation.
• Concrete bases and mixes and sealants.
• Cabinet alignment.
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 140 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Underground Cables and Termination COURSE REFERENCE: M504 DURATION: 7 hours (Recommended Minimum Duration)
CERTIFICATION: M501, M503, M504 and M505 combined COURSE AIMS This course aims to provide suitably qualified Installation Operatives with the knowledge and practical key skills required to install a combination of cable types and correctly wire to site specifications. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after installing equipment.
• Install different types of underground cables.
• Correctly strip, and prepare cable for final terminations.
• Terminate cable cores to meet required specifications and customer requirements.
• Identify cable types.
• Work to manufactures instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cable types and installation.
• Cable preparation and termination.
• Controller connections.
• Pole top connections.
• Variation reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 141 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Supply Tails and Earthing COURSE REFERENCE: M505 DURATION: 4-hours (Recommended Minimum Duration)
CERTIFICATION: M501, M503, M504 and M505 combined COURSE AIMS This course aims to provide suitably qualified Installation Operatives with the knowledge and practical key skills required to install supply tails and earthing to non-energised termination points in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Apply appropriate Health and Safety measures to safe guard workers and public.
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after installing cables.
• Recognise types and methods of earth bonding.
• Test Earth Bonding.
• Identify cable types and designations.
• Identify correct polarity connections.
• Work to manufactures instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks
• Onsite precautions
• Cable types and installation (concentric/slit concentric)
• Cable preparation and termination.
• Types of bonding.
• Testing methods
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 142 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of Ancillary Equipment COURSE REFERENCE: M506 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified Installation Operatives with the knowledge and practical key skills required to install a generic set of typical ancillary equipment used for monitoring and the control of traffic control equipment in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Apply appropriate Health and Safety measures to safe guard workers and public.
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after installing cables.
• Correctly install Urban Traffic Control Units.
• Correctly install Monitoring and Control equipment.
• Identify cable types.
• Identify correct polarity connections.
• Work to manufacturers and specification instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks
• Onsite precautions
• Cable types and installation methods
• Cable preparation and termination.
• Control and monitoring terminology.
• Equipment types
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 143 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Using Test Equipment on Non-Energised Circuits to BS 7671 COURSE REFERENCE: M405 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: M405 and M507 combined. Also available as M405 and . combined. COURSE AIMS This course aims to provide Traffic Highway Electricians/Service Operatives and Installers with a theoretical understanding of IET wiring Regulations (BS 7671), as they apply to Street Furniture. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Assess the Hazards and Risks.
• Gain Authority to carry out testing after site isolation confirmation.
• Demonstrate the concepts of earthing, bonding and insulation as described in the regulations.
• Demonstrate the regulations concerning electrical testing.
• Use appropriate Test Equipment correctly and safely.
• State the need for non-energised Electrical Testing.
• List the tests, test equipment and test methods.
• Complete and interpret the appropriate parts of Organisation. Traffic Installation Completion Certificate.
COURSE TOPICS:
• Basic Electrical Principles.
• Electrical testing for new installations.
• Test methods and working practices.
• Using the relevant test equipment.
• Measuring resistance and associated calculations.
• The Traffic Installation completion certificate. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 144 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Non-Energised Inspections COURSE REFERENCE: M507 DURATION: 4-hours (Recommended Minimum Duration) CERTIFICATION: M405 and M507 combined COURSE AIMS This course aims to provide suitably qualified Installation Operatives with the knowledge and practical key skills required to inspect non-energised installations to ensure installations are in accordance with manufacturing/customer requirements and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
.
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after installing cables.
• Check installations are compliant with manufacturer/customer specifications.
• Check installations are compliant with current legislative requirements.
• Check site and housekeeping requirements.
• Produce a defect rectification list.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Non-energised completion certificate records.
• Site installation completion checks.
• Installation compliancy.
• Site ground works completion checks.
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 145 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Routine Optical Maintenance of lanterns and PBU’s incl.
cleaning COURSE REFERENCE: M601a DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course. Also available as M601a and M601b
combined COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to carry out routine maintenance including lamp changing and cleaning PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, accessing Poles, Lanterns and PBU’s
• Carry out cleaning of equipment
• Carry out lamp changing
• Carry out functional testing.
• Identify and work with LV & ELV circuits safely.
• Report actions and unsafe site conditions to correct personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Review of installation practices
• Pole and Lantern Types and maintenance.
• LED systems
• Action reporting and tests. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 146 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Maintenance of Poles, Lanterns and Brackets COURSE REFERENCE: M601b DURATION: 10 hours (Recommended Minimum Duration) CERTIFICATION: M601a and M601b combined COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to maintain a combination of Poles, brackets and Lantern types in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before accessing Poles and Lanterns
• Be familiar with fault reports and be able to confirm faults.
• Carry out correct electrical/mechanical fault assessment using a range of test equipment.
• Maintain different types of lanterns associated with traffic installations.
• Carryout correct manufacturer testing procedures.
• Identify and work with LV circuits safely.
• Report actions and unsafe site conditions to correct personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Review of installation practices
• Pole and Lantern Types and maintenance.
• LED systems
• Other Pole furniture maintenance.
• Bracket types and maintenance.
• Action reporting and tests. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 147 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Traffic Controller Foundation Principles COURSE REFERENCE: M602 DURATION: 11 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to understand the common concepts associated with Traffic Controller operations and to maintain a combination of Cabinet types in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, accessing cabinets.
• Be familiar with fault reports and be able to confirm faults.
• Carry out correct electrical/mechanical fault assessment and rectification.
• Describe the Traffic controller hardware concepts.
• Use common handset command functions during investigations.
• Report actions and unsafe site conditions to correct personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cabinet Maintenance/Assessments
• The Traffic Controller, concepts and build
• Power supplies
• Common basic handset commands
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 148 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Detection Foundation Principles (Standard) COURSE REFERENCE: M603 DURATION: 10 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course. Also available as M603 and M611
combined. COURSE AIMS This course is designed to provide the attendees with the principles of vehicle and pedestrian detection necessary to facilitate the fundamental common concepts associated with the understanding of installation, commissioning and 1st line maintenance key skills in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, accessing cabinets.
• Be familiar with fault reports and be able to confirm faults.
• Carry out correct electrical/mechanical fault assessment and rectification using a range of test equipment.
• State the principles associated with detection and loop configurations.
• State the requirements for detector configurations and common operational features.
• Report actions and unsafe site conditions to correct personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Detector Principles
• Detector Maintenance/Assessments
• Detector Types, Pedestrian, Above Ground, Below Ground
• Power supplies
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 149 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Maintenance of Underground Cable COURSE REFERENCE: M604 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course is designed to provide the attendees with the principles necessary to facilitate the fundamental common concepts associated with the understanding of Underground Cable Maintenance in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before and during maintenance activities.
• Maintain different types of underground cables.
• Identify cable types.
• Test cable to required specifications
• Work to manufactures instructions.
• Report actions and unsafe sites to correct personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cable types and maintenance.
• Data, Signal, Supply Power, Neutrals, and Active Cables.
• Testing Methods.
• Action reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 150 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Maintenance of Supply Tails and Earthing COURSE REFERENCE: M605 DURATION: 4-hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to maintain supply tails and earthing to accepted commissioned standards in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Apply appropriate Health and Safety measures to safe guard workers and public.
• Identify Hazards and reduce Risks.
• Take necessary precautions before and during maintenance of cables.
• Recognise types and methods of earth bonding.
• Test Earth Bonding using correct test equipment.
• Identify cable types and designations.
• Identify correct polarity connections.
• Work to manufactures instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks
• Onsite precautions
• Cable types and installation (concentric/slit concentric)
• Common cable faults.
• Types of bonding.
• Testing methods
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 151 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Urban Traffic Control Fundamental Principles COURSE REFERENCE: M606 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to maintain and understand the common concepts associated with a combination UTC operations in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before accessing cabinets.
• Be familiar with fault reports and be able to confirm faults.
• Describe the Ancillary Control principles and hardware concepts.
• Use common handset command functions during investigations.
• Report actions and unsafe sites to correct personnel. COURSE TOPICS:
• Hazards and Risks and Onsite precautions.
• Ancillary equipment maintenance/assessments for O.T.U and U.T.M.C
• The Traffic Controller, concepts and common builds for O.T.U and U.T.M.C equipment
• Power supplies
• Common basic handset commands
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 152 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Monitoring and Control Fundamental Principles COURSE REFERENCE: M607 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to maintain and understand the common concepts associated with a combination of Ancillary Equipment operations in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before accessing cabinets.
• Be familiar with fault reports and be able to confirm faults.
• Describe Ancillary Monitoring principles and hardware concepts.
• Use common handset command functions during investigations.
• Report actions and unsafe sites to correct personnel. COURSE TOPICS:
• Hazards and Risks and Onsite precautions.
• Ancillary equipment maintenance/assessments for OMCU, OMU.
• The Traffic Controller, concepts and common builds for OMCU, OMU equipment
• Power supplies
• Common basic handset commands
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 153 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Pedestrian Traffic Controller Maintenance for (Equipment Name) COURSE REFERENCE: M608 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course on a per employee basis within an eighteen month timeframe, to cover a number of items of electrical equipment which would be named on the certificate. Additional equipment outside this period would be based on additional certification per piece of equipment COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to Commission and carry out First Line Maintenance key skills on Pedestrian Crossing Controller equipment as stated above, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, accessing cabinets.
• Be familiar with fault reports and be able to confirm faults.
• List and describe the associated component parts of the controller.
• Explain the TR141 or equivalent site data sheets.
• Demonstrate use of the handset commands.
• Test and commission controllers.
• Test and prove RLMU and LMU configurations.
• Successfully download site data and test.
• Report actions and unsafe sites to correct personnel. COURSE TOPICS:
• Hazards and Risks.
• Controller facilities, modes and related traffic concepts.
• Understanding of the site specification sheets.
• Full Hardware descriptions to block diagram level.
• Commands and handset/PC operations.
• Timetables, Seasonal Clocks and Cableless Linking Facilities
• Routine Servicing and Periodic Inspections and Commissioning.
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 154 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Junction Traffic Controller Maintenance for (Equipment Name) COURSE REFERENCE: M609 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course on a per employee basis within an eighteen month timeframe, to cover a number of items of electrical equipment which would be named on the certificate. Additional equipment outside this period would be based on additional certification per piece of equipment COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to Commission and carry out First Line Maintenance key skills on Junction Controller equipment as stated above, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Be familiar with fault reports and be able to confirm faults.
• List and describe the associated component parts of the controller.
• Explain the TR141 or equivalent site data sheets.
• Diagnose and rectify faults by block replacement.
• Demonstrate use of the handset commands.
• Test and commission controllers.
• Test and prove RLMU and LMU configurations.
• Successfully download site data and test.
• Report actions and unsafe sites to correct personnel. COURSE TOPICS:
• Hazards and Risks.
• Controller facilities, modes and related traffic concepts.
• Understanding of the site specification sheets.
• Full Hardware descriptions to block diagram level.
• Commands and handset/PC operations.
• Timetables, Seasonal Clocks and Cableless Linking Facilities
• Routine Servicing and Periodic Inspections and Commissioning.
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 155 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Detector Maintenance for …(Add Equipment Name) COURSE REFERENCE: M611 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: M603 and M611 combined. Also available individually for this course on a
per employee basis within an eighteen month timeframe, to cover a number of items of electrical equipment which would be named on the certificate. Additional equipment outside this period would be based on additional certification per piece of equipment.
COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to Commission and carry out First Line Maintenance key skills on Detector equipment as stated above, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Be familiar with fault reports and be able to confirm faults.
• List and describe the associated component parts of the Detector.
• Explain the TR141 or equivalent site data sheet requirements.
• Explain the operation of the Detector and associated modes.
• Describe the hardware operational and configuration features.
• State the maintenance requirements for the Detector.
• Diagnose and rectify faults by block replacement.
• Test and commission detector on site.
• Report actions and unsafe sites to correct personnel. COURSE TOPICS:
• Hazards and Risks.
• Detector facilities, modes and related traffic concepts.
• Understanding of the site specification sheets.
• Full Hardware descriptions to block diagram level.
• Routine Servicing and Periodic Inspections and Commissioning.
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 156 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Commissioning Procedures COURSE REFERENCE: M701 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: .. M701 COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to correctly commission Traffic Control, Ancillary Control/Monitoring and Street Furniture equipment. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Apply appropriate Health and Safety measures to safe guard workers and public.
• Identify Hazards and reduce Risks.
• Verify installations are compliant with manufacturer/customer specifications.
• Verify installations are compliant with current legislative requirements.
• Report variations and unsafe conditions to site build.
• Produce a defect rectification list. COURSE TOPICS:
• Hazards and risks.
• Safe Practices.
• Commissioning concepts for Traffic Control Equipment.
• Commissioning concepts for Ancillary Control/Monitoring Equipment.
• Commissioning concepts for Street Furniture. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 157 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Transmission Systems and Techniques Fundamentals (Named) COURSE REFERENCE: M702 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to apply Transmission System Fundamentals and Techniques to a range of common products, and to enable an in-depth understanding of principles when attending associate product training courses.. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before, accessing cabinets.
• Be familiar with fault reports and be able to confirm faults.
• Describe Transmission System hardware concepts.
• Use common handset command functions.
• Describe Transmission Concepts COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Hardware Identification
• The Transmission, concepts and build
• Common basic handset commands PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 158 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Traffic Signal Configuration (Add Equipment Name) COURSE REFERENCE: M703 DURATION: 21 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to Configure Traffic Control equipment to customer specification requirements. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Implement Customer Requirement.
• Comply with current legislation.
• Effectively use configuration application.
• Effectively use ancillary application components.
• Configure basic special configuration requirements.
• Verify correct system operations to customer specification. COURSE TOPICS:
• Customer needs and forms.
• Current Legislation requirements.
• Using the configuration tool.
• Special Conditioning
• Verification of configurations.
• Additional Application Software PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 159 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Advanced Traffic Principles COURSE REFERENCE: M704 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to use advanced tools and thought processes to logically evaluate and reason problems, associated with on street equipment configurations. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Explain in detail site data sheets
• State in-depth advance traffic control modes of operation.
• Explain the principles and facilities associated with controller specification sheets.
• Demonstrate user configuration commands associated with traffic controllers.
• Identify command structure for control interrogation COURSE TOPICS:
• A description at block diagram level of the controller hardware.
• Detection controller configuration concepts
• Facilities: Timetables and Clocks, Early Cut-off and Late Release, Gap changes, Dummy Phases, Conditions of Appearance
• The Controller Specification Sheets.
• Uses of the handset for enhanced checking of controller operation, facilities.
• Advance modes UTC, CLF, Part time, Bus/LRT/Emergency, Hurry Call.
PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 160 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Advance Detection Techniques (Add Equipment Name) COURSE REFERENCE: M705 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to monitor, test and commission the Detection Equipment as stated above, and using a range of standard and specialist test equipment to carry out First Line Maintenance key skills, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Complete and evaluate Risks and Hazards.
• Identify equipment hardware and set to work
• Test and Commission on site detection equipment.
• Identify and apply associated technology requirements
• Successfully complete routine servicing and inspections.
• Successfully carry out fault recognition and rectification.
• Accurately report finding and actions taken. COURSE TOPICS:
• Associated Risks and Hazards.
• Equipment type technology.
• Equipment type servicing.
• Faults and rectification PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience and will include associated tools and specialist test equipment to enable the full learning outcomes.
Highway Electrical Training Specification © HESA
Issue12.17 Page 161 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Ancillary Control & Monitoring Equipment Skills: -
(Add Equipment Name) COURSE REFERENCE: M706 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to monitor, test and commission the Ancillary Control and Monitoring Equipment as stated above, and using a range of standard and specialist test equipment to carry out First Line Maintenance key skills, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Correctly identify Hazards and Risks.
• Identify equipment hardware and set to work
• Correctly configure and commission the associated equipment.
• Identify and monitor the associated facilities
• Use advance handset and software applications.
• Carry out correct electrical and mechanical fault assessment.
• Use a range of test equipment and specialist to type equipment. COURSE TOPICS:
• Risks and hazards.
• Advance command sets.
• Commissioning and configuration.
• Testing and fault recognition
• Specialist test equipment and tools. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience and will include associated tools and specialist test equipment to enable the full learning outcomes.
Highway Electrical Training Specification © HESA
Issue12.17 Page 162 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Monitoring Equipment Skills:-(Add Equipment Name/Use) COURSE REFERENCE: M707 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to monitor, test and commission the Monitoring Equipment as stated above, and using a range of standard and specialist test equipment to carry out First Line Maintenance key skills, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Correctly identify Hazards and Risks.
• Identify equipment hardware and set to work
• Correctly configure and commission the associated equipment.
• Identify and monitor the associated facilities
• Use advance handset and software applications.
• Carry out correct electrical and mechanical fault assessment.
• Use a range of test equipment and specialist to type equipment.
COURSE TOPICS:
• Risks and hazards.
• Advance command sets.
• Commissioning and configuration.
• Testing and fault recognition
• Specialist test equipment and tools.
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience and will include associated tools and specialist test equipment to enable the full learning outcomes.
Highway Electrical Training Specification © HESA
Issue12.17 Page 163 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Microprocessor Optimised Vehicle Actuation Maintenance
(Add Equipment Name) COURSE REFERENCE: M708 DURATION: 28 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to monitor, test and commission the Microprocessor Optimised Vehicle Actuated Equipment as stated above, and using a range of standard and specialist test equipment to carry out First Line Maintenance key skills, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State basic MOVA principles.
• Identify equipment hardware and set to work
• Correctly use communication tools and applications.
• Correctly interpret dataset information
• Install and commission associated equipment.
• Correctly test and carry out inspections.
• Interpret fault messages and correctly rectify.
• Leave on controlled junction in full working order COURSE TOPICS:
• Principles.
• Communication Tools.
• Installation, Commissioning and Testing.
• Site Dataset information
• Fault messages and meaning PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience and will include associated tools and specialist test equipment to enable the full learning outcomes.
Highway Electrical Training Specification © HESA
Issue12.17 Page 164 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Road Transport Passenger Information Systems
(Add Equipment Name) COURSE REFERENCE: M709 DURATION: 28 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to monitor, test and commission the Road Transport Passenger Information Equipment as stated above, and using a range of standard and specialist test equipment to carry out First Line Maintenance key skills, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Risks and Hazards
• State basic RTPI principles.
• Identify equipment hardware and set to work
• Correctly use communication tools and applications.
• Install and commission associated equipment.
• Correctly test and carry out inspections.
• Interpret fault messages and correctly rectify.
• Monitor, test and install passenger display units.
• Monitor, test and install on bus units COURSE TOPICS:
• Principles.
• Communication Tools.
• Installation, Commissioning and Testing.
• Hardware identification
• Fault messages and meaning. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience and will include associated tools and specialist test equipment to enable the full learning outcomes.
Highway Electrical Training Specification © HESA
Issue12.17 Page 165 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Initial and Periodic Electrical Inspection and Testing (Traffic Controls)
COURSE REFERENCE: 713 DURATION: 21 hours* (Recommended Minimum Duration. * For combined Traffic and Public Lighting the course minimum is 28 hours) CERTIFICATION: Available individually for this course COURSE AIMS: This course aims to provide operatives with the knowledge and skills required for Initial and periodic electrical inspection and testing of new, existing or refurbished installations. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending this course. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative theoretical and practical assessment based on agreed criteria will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Define the purpose and difference of initial and periodic inspection and testing
• Use appropriate Test Equipment correctly and safely.
• Define the tests, test equipment and test methods.
• Carry out initial inspection and testing.
• Carry out periodic inspection and testing
• Complete an appropriate Certificate.
• Explain the reasons for an appropriate record system
• Identify appropriate action for unsatisfactory results.
• Record and report variations
COURSE TOPICS:
• Hazards and risks
• Initial and periodic testing of new, existing and replacement Highway electrical equipment.
• Test methods and working practices
• Using Electrical Test Equipment.
• Calculation of Earth Loop Impedance.
• Types of certificates used in Highway Electrical works PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience. The practical assessments will be carried out as identified by the HESA assessment criteria, on equipment that either accurately reflects ‘real site conditions’ or ‘using defined’ equipment that enables full coverage of the testing requirements.
Highway Electrical Training Specification © HESA
Issue12.17 Page 166 of 200 © Highway Electrical Skills Academy
Section 7 – Specialist Modules
Communications
Sectio
n 7
– C
om
mu
nic
atio
ns
Highway Electrical Training Specification © HESA
Issue12.17 Page 167 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Communications Fundamental Principles COURSE REFERENCE: TCOM001 DURATION: 17 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to understand the common concepts associated with Communications operations and to maintain a combination of Cabinet types in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• State necessary precautions before, accessing cabinets.
• State fault reporting mechanisms
• State the principles of electrical/mechanical fault assessment and rectification.
• Describe the Communications hardware concepts.
• Identify diagnostic equipment and methods of interrogation
• Describe how to report actions and unsafe site conditions to relevant personnel.
COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cabinet Maintenance/Assessments
• Communications concepts and build
• System build
• Diagnostic equipment
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 168 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Communications Detection Fundamental Principles COURSE REFERENCE: TCOM002 DURATION: 10 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course. COURSE AIMS This course is designed to provide the attendees with the principles of communications detection necessary to facilitate the fundamental common concepts associated with the understanding of installation, commissioning and 1st line maintenance key skills in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• State necessary precautions before, accessing cabinets.
• State fault reporting mechanisms
• State the principles associated with detection and loop configurations.
• State the common operational features.
• State the principles of electrical/mechanical fault assessment and rectification.
• Describe how to report actions and unsafe site conditions to relevant personnel.
COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Principles of detectors incl. loop configurations and setting up
• Detector Maintenance/Assessments
• Detector Types - Above Ground, Below Ground
• System Build
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 169 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of non-Infrastructure equipment COURSE REFERENCE: TCOM003 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified Employees with the knowledge and practical key skills required to install a generic set of typical non-infrastructure equipment used for communications in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify appropriate Health and Safety measures to safe guard workers and public.
• Identify Hazards and reduce Risks.
• State necessary precautions before, during and after installing cables.
• Install Communications equipment
• Identify cable types.
• Identify correct polarity and connections.
• Work to manufacturers and specification instructions.
• Describe how to report variations to site build. COURSE TOPICS:
• Hazards and Risks
• Onsite precautions
• Cable types and installation methods
• Cable preparation and termination.
• Communications equipment terminology.
• Equipment types
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 170 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Maintenance of Cables for Communications COURSE REFERENCE: TCOM004 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course is designed to provide the attendees with the principles necessary to facilitate the fundamental common concepts associated with the understanding of Cable Maintenance in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• State necessary precautions before and during maintenance activities.
• Describe how to maintain different types of cables.
• Identify cable types.
• Work to required specifications
• Test cable to required specifications
• Describe how to report actions and unsafe sites to relevant personnel.
COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cable types and maintenance.
• Data, Signal, Supply Power, Neutrals, and Active Cables.
• Testing Methods including cable attenuation and frequency response; sheath testing.
• Action reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 171 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Maintenance of specialist Communications equipment
(Equipment Name) COURSE REFERENCE: TCOM005 DURATION: 10 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course on a per employee basis within an eighteen month timeframe, to cover a number of items of electrical equipment which would be named on the certificate. Additional equipment outside this period would be based on additional certification per piece of equipment COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to commission and carry out first line maintenance key skills on Communications equipment as stated above, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Explain fault reports and be able to confirm faults.
• List and describe the associated component parts of the equipment
• Diagnose and rectify faults by module replacement.
• Demonstrate use of the diagnostic equipment commands.
• Test and commission equipment to specification
• Describe how to report actions and unsafe sites to relevant personnel.
COURSE TOPICS:
• Hazards and Risks.
• Communications facilities, modes and related concepts.
• Test results
• Full Hardware descriptions to block diagram level.
• Commands and diagnostic equipment operations.
• Routine Servicing and Periodic Inspections and Commissioning.
• Results and action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 172 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Initial and Periodic Electrical Inspection and Testing (Communications)
COURSE REFERENCE: 716 DURATION: 21 hours* (Recommended Minimum Duration. * For combined Communications and Traffic Control the course minimum is 28 hours) CERTIFICATION: Available individually for this course COURSE AIMS: This course aims to provide operatives with the knowledge and skills required for Initial and periodic electrical inspection and testing of new, existing or refurbished installations. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending this course. A complete list of pre-course requirements is shown in the Contents. ASSESSMENT: A summative theoretical and practical assessment based on agreed criteria will follow the completion of this course. OBJECTIVES: On completion of the course learners will:
• Define the purpose and difference of initial and periodic inspection and testing
• Use appropriate Test Equipment correctly and safely.
• Define the tests, test equipment and test methods.
• Carry out initial inspection and testing.
• Carry out periodic inspection and testing
• Complete an appropriate Certificate.
• Explain the reasons for an appropriate record system
• Identify appropriate action for unsatisfactory results.
• Record and report variations
COURSE TOPICS:
• Hazards and risks
• Initial and periodic testing of new, existing and replacement Highway electrical equipment.
• Test methods and working practices
• Using Electrical Test Equipment.
• Calculation of Earth Loop Impedance.
• Types of certificates used in Highway Electrical works PRACTICAL: To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience. The practical assessments will be carried out as identified by the HESA assessment criteria, on equipment that either accurately reflects ‘real site conditions’ or ‘using defined’ equipment that enables full coverage of the testing requirements.
Highway Electrical Training Specification © HESA
Issue12.17 Page 173 of 200 © Highway Electrical Skills Academy
Section 8 – Specialist Modules
Variable Message Signs
Sectio
n 8
– V
aria
ble
Me
ss
ag
e S
ign
s
Highway Electrical Training Specification © HESA
Issue12.17 Page 174 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of non-Infrastructure equipment – Variable Message
Signs COURSE REFERENCE: TVMS001 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified Employees with the knowledge and practical key skills required to install a generic set of typical non-infrastructure equipment used for variable message signs in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• State appropriate Health and Safety measures to safe guard workers and public.
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after installing cables.
• Install Variable Message Sign equipment
• Identify cable types.
• Identify correct polarity and connections.
• Work to manufacturers and specification instructions.
• Describe how to report variations to site build. COURSE TOPICS:
• Hazards and Risks
• Onsite precautions
• Cable types and installation methods
• Cable preparation and termination.
• Variable Message Sign equipment terminology.
• Equipment types
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 175 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Maintenance of specialist VMS equipment (Equipment Name) COURSE REFERENCE: TVMS002 DURATION: 10 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course on a per employee basis within an eighteen month timeframe, to cover a number of items of electrical equipment which would be named on the certificate. Additional equipment outside this period would be based on additional certification per item of equipment COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to commission and carry out first line maintenance key skills on variable message signs equipment as stated above, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Explain fault reports and be able to confirm faults.
• List and describe the associated component parts of the equipment
• Diagnose and rectify faults by module replacement.
• Demonstrate use of the diagnostic equipment commands.
• Test and commission equipment to specification
• Describe how to report actions and unsafe sites to relevant personnel.
COURSE TOPICS:
• Hazards and Risks.
• Variable Message Sign types, facilities, modes and related concepts (including associated detection modes).
• Test results
• Full Hardware descriptions to block diagram level.
• Commands and diagnostic equipment operations.
• Routine Servicing and Periodic Inspections and Commissioning.
• Results and action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 176 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Commissioning Procedures - Variable Message Signs
(Equipment name) COURSE REFERENCE: TVMS003 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to commission Variable Message sign equipment. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Apply appropriate Health and Safety measures to safe guard workers and public.
• Identify Hazards and reduce Risks.
• Verify installations are compliant with manufacturer/customer specifications.
• Verify installations are compliant with current legislative requirements.
• Reporting including variations and unsafe conditions to site build.
• Produce a defect rectification list. COURSE TOPICS:
• Hazards and risks.
• Safe Practices.
• Commissioning concepts for Variable Message Signs.
• Commissioning concepts for Ancillary Control/Monitoring Equipment. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 177 of 200 © Highway Electrical Skills Academy
Section 9 – Specialist Modules
Environmental and Monitoring Equipment
Sectio
n 9
– E
nviro
nm
en
tal a
nd
Mo
nito
ring
Eq
uip
men
t
Highway Electrical Training Specification © HESA
Issue12.17 Page 178 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Environmental Monitoring Equipment Fundamental Principles COURSE REFERENCE: TME001 DURATION: 17 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to understand the common concepts associated with Environmental monitoring equipment operations and to maintain a combination of Cabinet types in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Take necessary precautions before accessing cabinets.
• State fault reporting mechanisms
• State the principles of electrical/mechanical fault assessment and rectification.
• Describe Environmental Monitoring Equipment hardware concepts.
• Identify diagnostic equipment and methods of interrogation
• Report actions and unsafe site conditions to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cabinet Maintenance/Assessments
• Environmental Monitoring Equipment concepts and build
• System build
• Diagnostic equipment
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 179 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of non-infrastructure Environmental & Monitoring
Equipment
COURSE REFERENCE: TME002 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified Employees with the knowledge and practical key skills required to install a generic set of typical non-infrastructure equipment used for Environmental monitoring equipment in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Apply appropriate Health and Safety measures to safe guard workers and public.
• Identify Hazards and reduce Risks.
• Take necessary precautions before, during and after installing cables.
• Install Environmental monitoring equipment
• Identify types and sources of supply
• Identify cable types.
• Identify correct polarity and connections.
• Work to manufacturers and specification instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks
• Onsite precautions
• Cable types and installation methods
• Cable preparation and termination.
• Environmental monitoring equipment terminology.
• Equipment types
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 180 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Maintenance of Environmental & Monitoring Equipment COURSE REFERENCE: TME003 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to commission and carry out first line maintenance key skills on Environmental Monitoring equipment as stated above, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Explain fault reports and be able to confirm faults.
• List and describe the associated component parts of the equipment
• Diagnose and rectify faults by modular replacement.
• Demonstrate use of the diagnostic equipment
• Test and commission equipment to specification
• Report actions and unsafe sites to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Environmental Monitoring equipment
• Test results
• Full Hardware descriptions to block diagram level.
• Diagnostic equipment operations.
• Routine Servicing and Periodic Inspections and Commissioning.
• Results and action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 181 of 200 © Highway Electrical Skills Academy
Section 10 – Specialist Modules
Cameras
Sectio
n 1
0 –
Cam
era
s
Eq
uip
me
nt
Highway Electrical Training Specification © HESA
Issue12.17 Page 182 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Install Data Communications Cable COURSE REFERENCE: TCAM001 DURATION: 7 hours (Recommended Minimum Duration)
CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to install a combination of cable types to site specifications. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and Risks.
• Identify cable types.
• State necessary precautions before, during and after installing cables
• Install different types of cables to client specification / manufacturer’s instructions
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cable types and installation.
• Variation reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 183 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Terminate Cable COURSE REFERENCE: TCAM002 DURATION: 7 hours (Recommended Minimum Duration)
CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to terminate a number of cable types and wire to site specifications. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• State necessary precautions before, during and after work
• Identify cable types
• Prepare cable for final terminations.
• Terminate cable cores to meet required specifications and customer requirements.
• Work to client specification / manufacturer’s instructions.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cable types and installation.
• Cable preparation and termination.
• Variation reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 184 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Installation of non-Infrastructure equipment – Camera / head
assembly COURSE REFERENCE: TCAM003 DURATION: 3.5 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified employees with the knowledge and practical key skills required to install a generic set of typical non-infrastructure equipment used for cameras in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• Identify cable types
• State necessary precautions before, during and after work
• Install Camera equipment in accordance with client specification / manufacturer’s instructions
• Identify correct polarity and connections.
• Report variations to site build. COURSE TOPICS:
• Hazards and Risks
• Onsite precautions
• Cable types and installation methods
• Cable preparation and termination.
• Camera equipment terminology.
• Equipment types
• Variation reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 185 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Routine Optical Maintenance of Cameras COURSE REFERENCE: TCAM004 DURATION: 3.5 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course. COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to carry out routine optical maintenance of cameras PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and Risks.
• State necessary precautions before, during and after accessing Cameras
• Carry out cleaning of equipment in accordance with client specification / manufacturers instructions
• Carry out functional testing in accordance with client specification / manufacturer’s instructions
• Report actions and unsafe site conditions to relevant personnel. COURSE TOPICS:
• Hazards and Risks
• Environmental considerations
• Onsite precautions.
• Camera Types and routine optical maintenance.
• Action reporting and tests. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 186 of 200 © Highway Electrical Skills Academy
Training Course Syllabus
COURSE TITLE: Maintenance of Camera / head assembly COURSE REFERENCE: TCAM005 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course. COURSE AIMS This course aims to provide employees working in the highway electrical sector with the knowledge and practical key skills required to carry out camera maintenance PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• State necessary precautions before accessing Camera / head assembly
• Carry out maintenance of equipment in accordance with client specification / manufacturer’s instructions
• Carry out alignment and functional testing in accordance with client specification / manufacturer’s instructions
• Report actions and unsafe site conditions to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Review of installation practices
• Camera Types / head assembly maintenance.
• Action reporting and tests. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 187 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Maintenance of Cable COURSE REFERENCE: TCAM006 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course is designed to provide the attendees with the principles necessary to facilitate the fundamental common concepts associated with the understanding of Cable Maintenance in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and reduce Risks.
• State necessary precautions before and during maintenance activities.
• Maintain different types of cables in accordance with client specification / manufacturer’s instructions.
• Identify cable types.
• Test cable to required client specification / manufacturer’s instructions.
• Report actions and unsafe sites to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Cable types and maintenance.
• Testing Methods.
• Action reporting. . PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 188 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Detector Maintenance for …(Add Equipment Name) COURSE REFERENCE: TCAM007 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course on a per employee basis within an eighteen month
timeframe, to cover a number of items of electrical equipment which would be named on the certificate. Additional equipment outside this period would be based on additional certification per piece of equipment.
COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to Commission and carry out First Line Maintenance key skills on Detector equipment as stated above, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and Risks.
• Identify typical faults
• List and describe the associated component parts of the Detector.
• Explain site data sheet information.
• Explain the operation of the Detector and associated modes.
• Describe the hardware operational and configuration features.
• State the maintenance requirements for the Detector.
• Diagnose and rectify faults by module replacement.
• Test and commission detector on site.
• Report actions and unsafe sites to relevant personnel. COURSE TOPICS:
• Hazards and Risks.
• Detector facilities, modes and related traffic concepts.
• Site specification sheets.
• Hardware descriptions to block diagram level.
• Routine Servicing and Periodic Inspections and Commissioning.
• Action reporting. PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 189 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Commissioning Procedures for Camera (Equipment Name) COURSE REFERENCE: TCAM008 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available for this course individually on a per employee basis within an eighteen month
timeframe, to cover a number of items of electrical equipment which would be named on the certificate. Additional equipment outside this period would be based on additional certification per piece of equipment.
COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to commission Camera Equipment / head assemblies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and Risks.
• Verify installations are compliant with customer specifications / manufacturer’s instructions.
• Report variations and unsafe conditions to site build.
• Produce a defect rectification list. COURSE TOPICS:
• Hazards and risks.
• Safe Practices.
• Commissioning concepts for Camera / head assembly
PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 190 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Transmission Systems and Techniques Fundamentals COURSE REFERENCE: TCAM009 DURATION: 7 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to apply Transmission System Fundamentals and Techniques to a range of common products, and to enable an in-depth understanding of principles when attending associate product training courses.. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and Risks.
• State necessary precautions before accessing cabinets.
• State the principles of Transmission Systems concepts and protocols.
COURSE TOPICS:
• Hazards and Risks.
• Onsite precautions.
• Transmission system concepts and build PRACTICAL:
To enable maximum learning and benefit from this course, there will a number of exercises. These may be both interactive and demonstrative to enhance the learning experience.
Highway Electrical Training Specification © HESA
Issue12.17 Page 191 of 200 © Highway Electrical Skills Academy
Training Course Syllabus COURSE TITLE: Ancillary Equipment Skills: -
(Add Equipment Name) COURSE REFERENCE: TCAM010 DURATION: 14 hours (Recommended Minimum Duration) CERTIFICATION: Available individually for this course COURSE AIMS This course aims to provide suitably qualified staff with the skills necessary to monitor, test and commission the Ancillary Equipment as stated above, and using a range of standard and specialist test equipment to carry out First Line Maintenance key skills, in accordance with manufacturing and/or organisation and legislative policies. PREREQUISITES: In order to gain maximum benefit and learning outcomes from this course there are a number of training modules, which are required before attending. A complete list of pre-course requirements is as stated in the Contents. ASSESSMENT: A summative and practical assessment will follow the completion of this course or group of courses. OBJECTIVES: On completion of the course learners will:
• Identify Hazards and Risks
• Identify equipment hardware
• Identify the ancillary facilities
• Configure and commission the ancillary equipment.
• Use diagnostic equipment, software applications and specialist to type equipment
• Carry out electrical and mechanical fault assessment.
• Use appropriate test equipment COURSE TOPICS:
• Hazards and risks
• Transmission principles
• Diagnostic equipment
• Commissioning and configuration.
• Testing and fault recognition
• Specialist test equipment PRACTICAL:
To enable maximum learning and benefit from this course, there will be a number of exercises. These may be both interactive and demonstrative to enhance the learning experience and will include associated tools and specialist test equipment to enable the full learning outcomes.
Highway Electrical Training Specification © HESA
Issue12.17 Page 192 of 200 © Highway Electrical Skills Academy
Appendix 1
Refresher Training Details
Ap
pen
dix
1 –
Refre
sh
er T
rain
ing
De
tails
Eq
uip
me
nt
Highway Electrical Training Specification © HESA
Issue12.17 Page 193 of 200 © Highway Electrical Skills Academy
Appendix 1 - Refresher Training Details
Course Ref No
Title
Training Method
Full Course
None Emergency First Aid at Work Y
101 Health, Safety and Environment
102 Control of substances hazardous to health
103 Electrical Safety
104 Moving and Handling Y
105 Interpretation of Legislation & Standards
106 Emergency Arrangements
201 Hazards and Risk Assessment Y
203* Appreciation of Public Lighting and
T/Sign Equipment
other than new equipment
207 Effective Personal Protective Equipment
209 On Site Safety
S203* Appreciation of Traffic Sign Products & associated legislation and guidance
other than new equipment
M203* Traffic Product Appreciation other than new equipment
202 Avoiding Danger from Underground Services (training designed to meet the
assessment requirements of NRSWA Unit 1)
Y
204 Hand held Tools including Operating Hand Held Drills/ Screwdrivers
204.1 Power Tools including hand tools
(named equipment specific) Y
205.1 Work at height with steps and ladders
Y
205.2 Work at height with Scaffold Towers Y
205.3 Prefabricated Mobile Access and
Working Towers Y
206.1 Mobile Elevating Work Platform
awareness
206.2 MEWP Operators Course (Boom type) Y
206.3 MEWP Operators Course (Scissors type) Y
208 Loading, Transporting and Removing
Goods (Vehicular)
210 Work in the vicinity of DNO / IDNO
equipment – EREC G39 Issue 2 2013 Y
210.1
Work in the vicinity of DNO / IDNO equipment – EREC G39 Issue 2 2013
awareness Y
Course Title Training Method
Highway Electrical Training Specification © HESA
Issue12.17 Page 194 of 200 © Highway Electrical Skills Academy
Ref No Full Course
214 Safe Isolation Y
See Special Notes
215 Emergency Inspection Procedures
301.1 Excavate (training designed to meet the
assessment requirements of NRSWA Unit 3)
301.2
Minor excavation and temporary reinstatement in the highway for column
holes.
301.3
Reinstatement and compaction (training
designed to meet the assessment requirements of NRSWA Unit 4)
301.4 Reinstatement of sub-base and base
(leading to assessment to NRSWA Unit 5)
301.5
Reinstatement of cold lay bit-mat (training
designed to meet the assessment requirements of NRSWA Unit 6)
301.6
Reinstatement of hot lay bit-mat (training
designed to meet the assessment requirements of NRSWA Unit 7)
301.7
Reinstatement of concrete slabs (training
designed to meet the assessment requirements of NRSWA Unit 8)
301.8
Reinstatement of modular and concrete (training designed to meet the assessment
requirements of NRSWA Unit 9)
302.1
Temporary Traffic Management excl. Temp. Traffic signals
Y
302.2
Temporary Traffic Management - Temporary Traffic Signals Y
310
Monitoring Signing, Lighting & Guarding (training designed to meet the assessment
requirements of NRWSA Unit 10)
Y
311
Monitoring Excavation in the Highway (training designed to meet the assessment
requirements of NRWSA Unit 11)
312
Monitoring Reinstatement and Compaction
of Backfill Materials (training designed to meet the
assessment requirements of NRWSA Unit 12)
313
Monitoring Reinstatement of sub-base and top layer materials(training designed to
meet the assessment requirements of NRWSA Unit
13)
Course 214 – Following the initial course delivery, full course refresher is only required where the operative does not attend course 210,or the course 210 has been allowed to expire. In this case the 214 course certificate must be in date before attending the next 210 course, if not 214 course retake is required.
Highway Electrical Training Specification © HESA
Issue12.17 Page 195 of 200 © Highway Electrical Skills Academy
Course Ref No
Title
Training Method
Full Course
314 / M314
Monitoring reinstatement in bituminous material (training designed to meet the
assessment requirements of NRWSA Unit 14)
315 / M315
Monitoring reinstatement in concrete slabs(training designed to meet the assessment
requirements of NRWSA Unit 15)
316 / M316
Monitoring reinstatement in modular and concrete surfaces(training designed to meet
the assessment requirements of NRWSA Unit 16)
401.1 Basic Electrical Theory
401.2 Advanced Electrical Theory
402 Electricity at Work Regulations
403 BS7671: 2018 / IET Wiring Regs
Y
801 Coordinate the work of others on site
802
Set teams to work & Coordinate the work for Quality, Safety & Productivity
805 CDM Awareness
211 Lorry mounted crane – Slinger / Signaller
Y
212 Lorry mounted crane – Operator
Y
501 Erect Columns and Brackets
502 Remove columns and brackets
503 Re-align columns and brackets
504 Install feeder pillars
505 Install Base lit bollard base
508 Installation of base-lit bollard
506 Installation of lantern and bracket
507 Installation of wiring and control gear
509 Install underground cables
510 Terminate and connect U/G cable into
cut out
511 Joint underground cables
601 Night time monitoring
Highway Electrical Training Specification © HESA
Issue12.17 Page 196 of 200 © Highway Electrical Skills Academy
Course Ref No
Title
Training Method
Full Course
602 Painting of structures (being revised to
meet the requirements of SS 19A)
608 Operate raising and lowering columns
214 Safe Isolation Y See Special Notes
603 Routine General Maintenance
604 Visual Inspection-Optical, Structural &
Electrical
605 Remove and replace components
214 Safe Isolation Y See Special Notes
404 Familiarisation of circuits used in public
lighting
other than new equipment
604 Visual Inspection-Optical, Structural &
Electrical
606 Identify and replace faulty components
701 Diagnose fault & replace faulty
component
702 Emergency Work
705 Locate faults on underground cables
706 Periodic Structural Inspection and
Testing
707 Highway Lighting photometric testing
708 Maintaining high mast lighting
709 Install high mast lighting
710 Awareness of inspection & testing for
witnessing
717 Fundamental Inspection and Testing for
the Addition or Alteration to an Installation
Y
712, 713, 714, 715,
716
Initial and Periodic Electrical Inspection and Testing
Y
S203 Appreciation of Traffic Sign Products &
associated legislation and guidance
S301.7 Excavate & install in Embankments
S501 Erect Columns and Brackets (Posts)
over 140mm dia. In multi-post
Course 214 – Following the initial course delivery, full course refresher is only required where the operative does not attend course 210,or the course 210 has been allowed to expire. In this case the 214 course certificate must be in date before attending the next 210 course, if not 214 course retake is required.
Highway Electrical Training Specification © HESA
Issue12.17 Page 197 of 200 © Highway Electrical Skills Academy
Course Ref No
Title
Training Method
Full Course
S512.1
Install sign assembly up to 3 sq. m - sign plate and sign lighting unit only
(excluding connection)
S512.2
Install sign assembly 3-15 sq. m - sign plate and sign lighting unit only
(excluding connection)
S512.3
Install sign assembly over 15 sq. m - sign plate and sign lighting unit only
(excluding connection)
S513 Install sign on gantries & overhead
structures
S707 Inspection and photometric testing of
signs
TSC001 Cut Slot to Specification
TSC002 Lay Cable and Seal
TSC003 Repair Faulty Cable
TSC004 Access to cabinets through ducts etc.
TIE001 Installation of Supporting Structures (sector / equipment named)
TIE002 Installation of Cabinets (sector
/ equipment type)
TIE003 Installation of Standard Detection (sector
/ equipment type)
M203 Traffic Product Appreciation unless new equipment
M301 Traffic Principles
M501 Installation of Poles, Lanterns and Brackets - Infrastructure
M502 Installation of Cabinets and Roots - Infrastructure
M501 Installation of Poles, Lanterns and Brackets – Non-Infrastructure
M503 Installation of Standard Detection
M504 Installation of Underground Cables & Terminations
M505 Installation of Supply Tails and Earthing
M506 Installation of Ancillary Equipment
M405 Using Test Equipment on Non-Energised Circuits to BS 7671
Highway Electrical Training Specification © HESA
Issue12.17 Page 198 of 200 © Highway Electrical Skills Academy
Course Ref No
Title
Training Method
Full Course
M507 Non-Energised Inspections
M601a Routine Optical Maintenance of lanterns and PBU’s including cleaning
M601a Routine Optical Maintenance of lanterns and PBU’s including cleaning
M601b Maintenance of Pole, Lanterns and Brackets
M602 Traffic Controller Foundation Principles
M603 Detection Foundation Principles (Standard)
M604 Maintenance of Underground Cables
M605 Maintenance of Supply Tails and Earthing
M606 Urban Traffic Control Foundation Principles
M607 Monitoring and Control Foundation Principles
M608 Maintenance of Specific Pedestrian Controller Equipment (Named) Equipment
Code: -
M609 Maintenance of Specific Junction Controller Equipment (Named) Equipment
Code: -
M603 Detection Foundation Principles (Standard)
M611 Maintenance of Specific Detection Equipment Common working principles
M611 Maintenance of Specific Detection Equipment (Named) Equipment Code: -
M405 Using Test Equipment on Non-Energised Circuits to BS 7671
M701 Commissioning Procedures
M702 Transmission Systems and Techniques Fundamentals (Named) Equipment Code: -
M703 Traffic Signals Configuration (Named)
Equipment Code: -
M704 Advanced Traffic Principles
Course Title Training Method
Highway Electrical Training Specification © HESA
Issue12.17 Page 199 of 200 © Highway Electrical Skills Academy
Ref No Full
Course
M705 Advanced Detection Techniques
M706 Ancillary Control and Monitoring Equipment Skills (Named) Equipment Code: -
M707 Monitoring Equipment Skills (Named)
Equipment Code: -
M708 Microprocessor Optimised Vehicle Actuation Maintenance (Named) Equipment
Code: -
M709 Road Transport Passenger Information Systems (Named) Equipment Code: -
TCOM001
Communications Fundamental Principles
TCOM002
Communications Detection Fundamental Principles
TCOM003
Installation of non-Infrastructure Equipment Communications
TCOM004
Maintenance of cables for Communications
TCOM005
Maintenance of specialist Communications equipment (Named)
TVMS001 Installation of non-Infrastructure
Equipment - VMS
TVMS002 Maintenance of specialist VMS
equipment (Named)
TVMS003 Commissioning Procedures – VMS
(Named)
TME001 Env. & Monitoring Equip’t Fundamental
Principles
TME002 Installation of non-infrastructure Env. &
Monitoring Equip’t
TME003 Maintenance of Env. & Monitoring
Equip’t
TCAM001 Install Data Communications Cable
TCAM002 Terminate Cable
TCAM003 Installation of non-Infrastructure
Equipment – Camera / Head assembly
TCAM004 Routine optical maintenance of cameras
TCAM005 Maintenance of Camera / Head
assembly
TCAM006 Maintenance of cable
TCAM007 Detector Maintenance for (Named)
Equipment
Course Title Training Method
Highway Electrical Training Specification © HESA
Issue12.17 Page 200 of 200 © Highway Electrical Skills Academy
Ref No Full
Course
TCAM008 Commissioning Procedures for Camera
(Named)
TCAM009 Transmission Systems and Techniques
Fundamentals
TCAM010 Ancillary Equipment Skills (Named)
Special Notes Course 214 – Following the initial course delivery, full course refresher is only required where the operative does not attend course 210, or the course 210 has been allowed to expire. In this case the 214course certificate must be in date before attending the next 210 course, if not 214 course retake is required