High performance site components Combiners_Filters.pdfTriple Band Combiner Frequency range Description Connector Ordering number Triple Band Combiners DC-2170, 2400-2500, 5000-6000MHz

High performance site components

Introduction

Egant AB is one of the leading suppliers of products for Cellularinfrastructure.

Specialised in products that makes it possible to shareantenna systems, combining signals and designing cost effective mobile networks.

Egant AB works close together with its customers to make solutions and projects optimized for today’s demands.Giving you products that is always in the latest design and highest technology.

Our design centre in Stockholm Sweden is always happy for new challenges and welcomes all new projects and design ideas.

More information can be found at: www.egant.se

EGANT ABBox 945114 79 StockholmSwedenTel: +46 (0)8 6200 650Email: [email protected]: www.egant.se

Quad Band Combiner www.egant.se

Frequency range Description Connector Ordering numberQuad Band Combiner380-960, 1800, 2100, 2600MHz Quad Band Combiner 7/16(f) EG 601 0121

Quad Band CombinerTETRA/GSM900, GSM1800, UMTS, LTE2600

Combines 4 RBSs into 1 antenna port

This Quad Band Combiner enables the con-nection of 4 Radio Base Stations to the com-biner:

1 TETRA/GSM900 Radio Base Station1 GSM1800 Radio Base Station1 UMTS Radio Base Station1 LTE2600 Radio Base Station

The combiner combines the 4 signals to1 antenna port, or splits the signal to the 4 RBSs in the receiving direction.

This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.

Reduces cost

By utilizing our quad band combiner you will reduce the cost of antennas, feeders and installation.

It eliminates the cost inefficient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefits of antenna sharing.

Egant ABBox 945SE-114 79 Stockholm SwedenPhone: +46 (0)8 620 06 50 E-mail: [email protected]

RevC

Technical Specifications for the Quad Band CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:Passband: Port 1: Tetra - GSM900 Port 2: GSM1800 Port 3: UMTS Port 4: LTE2600

Insertion loss:

Input return loss:Isolation between systems: Max input power/port:Port 1:Port 2:Port 3:port 4:

Impedance in/out:

Intermodulation:IM3, 2 x 43 dBm:

DC by-pass between all inputs to output:

EG 602 0121 380- 960 MHz 1710 - 1880 MHz 1920 - 2170 MHz2500-2690MHz

< 0.30 dB

> 18 dB> 50 dB

< 300 W< 300 W< 300 W< 200 W

50 Ohm

<-110 dBm (153 dBc)

1A, max, per input

Mechanical SpecificationsDimensions (W x H x D):Connectors:Weight:

260 x 50 x 220 mm7/16 (f) 4 kg

Environmental Specifications Temp. range (normal operation):Humidity:Sealing:

Egant reserves the right to change this product specification at any time

without notice.

-40 to +70º CRelative 5 - 100% IP66

Triple Band Combiner www.egant.se

Frequency range Description Connector Ordering numberTriple Band CombinersDC-2170, 2400-2500, 5000-6000MHz Triple Band Combiner N(f) EG 602 015188-108, 376-495, 1570-1580MHz Triple Band Combiner 7/16(f) EG 602 0044376-480, 880-960, 1710-1880MHz Triple Band Combiner 7/16(f) EG 602 0178376-500, 880-960, 1920-2170MHz Triple Band Combiner 7/16(f) EG 602 0080806-960, 1710-1880, 1920-2170MHz Triple Band Combiner 7/16(f) EG 100 9012880-960, 1710-1880, 1920-2170MHz Triple Band Combiner SMA(f) EG 100 9019880-960, 1710-1880, 1920-2170MHz Triple Band Combiner N(f) EG 602 0041880-960, 1920-2170, 2500-2690MHz Triple Band Combiner 7/16(f) EG 602 0150

Triple Band CombinerDC-2170MHz, 2400-2500MHz,5000-6000MHz

This triple band combiner combines cellular networks with local wireless networks.The combiner combines the 3 signals to1 antenna port, or splits the signal in the re-ceiving direction.


Reduces cost

By utilizing the Egant triple band combiner you will reduce the cost of antennas, feeders and installation.



RevB

Technical Specifications for the Triple Band CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:Passband: Port 1: Port 2: Port 3:

Insertion loss: Port 1: - ANT Port 2: - ANT Port 3: - ANT

Input return loss:Isolation between systems: Max input power/port:

Impedance in/out:

Intermodulation:IM 3, 2 x 43 dBm:

EG 602 0151 DC - 2170 MHz 2400 - 2500 MHz 5000 - 6000 MHz

< 1.2 dB < 1.5 dB < 0.7 dB

> 14.0 dB> 45 dB

50W, (max 50W total)

50 Ohm

<-107 dBm (150 dBc)


222 x 25 x 127 mmN (f) 1.6 kg

Environmental Specifications Temp. range (normal operation):Humidity:


without notice.

-0 to +55º CRelative 5 - 100%

Triple Band Combiner160MHz, TETRA, GPS

Combines 3 Radio Systems into 1 An-tenna Port

This triple band combiner enables the connec-tion of 3 Systems to the combiner:

1 160MHz System1 TETRA System1 GSP System

The combiner combines the 3 signals to1 antenna port, or splits the signal to the 3 Systems in the receiving direction.

This is a highly desirable function when designing shared antenna systems wishing to connect multiple Radio Systems to the shared antennas.

Reduces cost




RevC


Electrical SpecificationsProduct number:Passband: Port 1: 160MHz Port 2: TETRA Port 3: GPS

Insertion loss: Port 1: 160MHz - ANT Port 2: TETRA - ANT Port 3: GPS - ANT

Input return loss:Isolation between systems: Max input power/port:Port 1: 160MHz Port 2: TETRA Port 3: GPS

Impedance in/out:

EG 602 0044 88 - 180 MHz 376 - 495 MHz 1570 - 1580 MHz

< 0.9 dB < 0.9 dB < 0.5 dB

> 14.0 dB> 30 dB

10 W20 W10 W

50 Ohm


350 x 130 x 60 mm7/16 (f) 3,5 kg



without notice.


Triple Band CombinerTETRA, GSM900, GSM1800


This triple band combiner enables the connec-tion of 3 Radio Base Stations to the combiner:

1 TETRA Radio Base Station1 GSM900 Radio Base Station1 GSM1800 Radio Base Station



Reduces cost

By utilizing our triple band combiner you will reduce the cost of antennas, feeders and installation.



RevB


Electrical SpecificationsProduct number:Passband: Port 1: TETRA Port 2: GSM900 Port 3: GSM1800

Insertion loss: Port 1: TETRA - ANT Port 2: GSM900 - ANT Port 3: GSM1800 - ANT

Input return loss:

Isolation between systems: Max input power/port:

Impedance in/out:


EG 602 0178 376 - 480 MHz 880 - 960 MHz 1710 - 1880 MHz

< 0.30 dB, typ 0,15dB < 0.55 dB, typ 0,3dB < 0.65 dB, typ 0,4dB

> 18.0 dB

> 50 dB

< 100 W

50 Ohm

153 dBc


300 x 150 x 500 mm7/16 (f) 8 kg



without notice.


Triple Band CombinerTETRA, GSM900, UMTS



1 TETRA Radio Base Station1 GSM900 Radio Base Station1 UMTS Radio Base Station



Reduces cost




RevC


Electrical SpecificationsProduct number:Passband: Port 1: TETRA Port 2: GSM900 Port 3: UMTS

Insertion loss: Port 1: TETRA - ANT Port 2: GSM900 - ANT Port 3: UMTS - ANT

Input return loss:Isolation between systems: Max input power/port:Port 1: TETRA Port 2: GSM900 Port 3: UMTS

Impedance in/out:


EG 602 0080 376 - 500 MHz 880 - 960 MHz 1920 - 2170 MHz

< 0.30 dB, typ 0,15dB < 0.55 dB, typ 0,3dB < 0.65 dB, typ 0,4dB

> 18.0 dB> 50 dB

< 200 W< 200 W< 100 W

50 Ohm

153 dBc


300 x 150 x 500 mm7/16 (f) 8 kg



without notice.


Triple Band Combiner/Dual Band Combiner UMTS, GSM1800, GSM900 / GSM1800, UMTS



1 GSM900 Radio Base Station1 GSM1800 Radio Base Station1 UMTS Radio Base Station



Reduces cost


It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefi ts of antenna sharing.

Dual Band Combiner - combines 2 RBSs into 1 antenna port

The dual band combiner enables you to connect 2 Radio Base Stations to the combiner:

1 GSM1800 Radio Base Station1 UMTS Radio Base Station

GSM

900

GSM

900

GSM

180

0G

SM 1

800

UM

TSU

MTS

ANTANT

Egant ABBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50E-mail: [email protected]

RevF

Technical Specifi cations for the Triple Band Combiner/Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband:Port 1: GSM900Port 2: GSM1800Port 3: UMTS

Insertion loss:Port 1: GSM900 - ANTPort 2: GSM1800 - ANTPort 3: UMTS - ANT

Input return loss:Isolation between systems:

Max input power/port:Port 1: GSM900Port 2: GSM1800Port 3: UMTS

Impedance in/out:



EG 100 9012

698 - 960 MHz1710 - 1880 MHz1920 - 2170 MHz

< 0.20 dB < 0.30 dB < 0.45 dB

> 21.0 dB> 50 dB

< 200 W< 200 W< 100 W

50 Ohm

<-110 dBm (153 dBc)

1A, max, per input

EG 100 9009

1710 - 1880 MHz1920 - 2170 MHz

< 0.40 dB < 0.45 dB

> 20.0 dB> 50 dB

< 200 W< 100 W

50 Ohm

<-110 dBm (153dBc)

1A, max, per input

Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:

230 x 200 x 555 mm7/16 (f)3.6 kg

245 x 210 x 50 mm7/16 (f)3.6 kg

Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:

Egant reserves the right to change this product specifi cation at any time

without notice.

-40 to +70º CRelative 5 - 100%IP66


Triple Band CombinerUMTS, GSM1800, GSM900

Combines 3 RBSs into 1 Antenna Port





Reduces cost



GSM

900

GSM

900

GSM

180

0G

SM 1

800

UM

TSU

MTS

ANTANT


RevD


Electrical SpecificationsProduct number:Passband: Port 1: GSM900 Port 2: GSM1800 Port 3: UMTS

Insertion loss: Port 1: GSM900 - ANT Port 2: GSM1800 - ANT Port 3: UMTS - ANT

Input return loss:Isolation between systems: Max input power/port:Port 1: GSM900 Port 2: GSM1800 Port 3: UMTS

Impedance in/out:

EG 100 9019 880 - 960 MHz 1710 - 1880 MHz 1920 - 2170 MHz

< 1.3 dB < 1.3 dB < 1.3 dB

> 16.0 dB> 30 dB

20 W20 W20 W

50 Ohm

EG 602 0041

880 - 960 MHz 1710 - 1880 MHz 1920 - 2170 MHz

< 1.3 dB < 1.3 dB < 1.3 dB

> 16.0 dB> 30 dB

20 W20 W20 W

50 Ohm


195 x 130 x 30 mmSMA (f) 1 kg

195 x 130 x 30 mmN (f)1 kg



without notice.



Triple Band CombinerGSM900, UMTS, LTE2600MHz



1 GSM900 Radio Base Station1 UMTS Radio Base Station1 LTE2600 Radio Base Station



Reduces cost




Rev C


Electrical SpecificationsProduct number:Passband: Port 1: GSM900 Port 2: UMTS Port 3: LTE2600

Insertion loss: Port 1: GSM900 - ANT Port 2: UMTS - ANT Port 3: LTE - ANT

Input return loss:Isolation between systems: Max input power/port: Port 1: GSM900Port 2: UMTSPort 3: LTE2600

Impedance in/out:


EG 602 0150 880 - 960 MHz 1920 - 2170MHz 2490 - 2690 MHz

< 0.25 dB < 0.25 dB < 0.25 dB

> 18.0 dB> 50 dB

< 300 W< 300 W< 300 W

50 Ohm

<-110 dBm (153 dBc)


230 x 50 x 200 mm7/16 (f) 3.6 kg



without notice.


Dual Band Combiner www.egant.se

Frequency range Description Connector Ordering numberDual Band Combiners68-470, 791-862MHz Dual Band Combiner 7/16(f) EG 602 018268-500, 700-2700MHz Dual Band Combiner N(f) EG 602 011568-500, 700-2700MHz Dual Band Combiner 7/16(f) EG 602 012068-500, 790-2700MHz Dual Band Combiner 7/16(f) EG 602 007268-470, 870-970MHz Dual Band Combiner N(f) EG 100 901568-470, 870-970MHz Dual Band Combiner 7/16(f) EG 100 901668-470, 870-970MHz Dual Band Combiner 7/16(f) EG 100 901768-2170, 2400-2500MHz Dual Band Combiner 7/16(f) EG 602 000780-240, 376-480MHz Dual Band Combiner N(f) EG 602 018380-240, 376-480MHz Dual Band Combiner N(f) EG 602 018480-240, 376-480MHz Dual Band Combiner 7/16(f) EG 602 003880-240, 376-480MHz Dual Band Combiner 7/16(f) EG 602 003080-960, 1710-2700MHz Dual Band Combiner N(f) EG 602 011180-960, 1710-2700MHz Dual Band Combiner 7/16(f) EG 602 0108155-500, 1575-1576MHz Dual Band Combiner 7/16(f) EG 602 0049376-500, 1920-2170MHz Dual Band Combiner N(f) EG 602 0045376-500, 1920-2170MHz Dual Band Combiner 7/16(f) EG 602 0046376-2170, 2400-2500MHz Dual Band Combiner N(f) EG 100 9018376-2170, 2400-2500MHz Dual Band Combiner 7/16(f) EG 100 9028376-2170, 2400-2500MHz Dual Band Combiner 7/16(m),7/16(f), N(f) EG 602 0007376-2170, 2500-2700MHz Dual Band Combiner N(f) EG 602 0076376-2170, 2500-2700MHz Dual Band Combiner 7/16(f) EG 602 0074380-395, 410-425MHz Dual Band Combiner N(f) EG 602 0023

Dual Band Combiner www.egant.se

380-395, 410-425MHz Dual Band Combiner 7/16(f) EG 602 0024380-395, 440-450MHz Dual Band Combiner 7/16(f) EG 602 0191380-395, 442,975-448,975MHz Dual Band Combiner N(f) EG 602 0176380-395, 450-470MHz Dual Band Combiner N(f) EG 602 0094790-862, 880-960MHz Dual Band Combiner N(f) EG 602 0112790-862, 880-960MHz Dual Band Combiner 7/16(f) EG 602 0097790-1000, 1710-2170MHz Dual Band Combiner 7/16(f) EG 602 0110800-1000, 1710-2170MHz Dual Band Combiner N(f) EG 100 9014800-1000, 1710-2170MHz Dual Band Combiner 7/16(f) EG 100 9013880-960, 1710-1880MHz Dual Band Combiner 7/16(f) EG 602 0034890-960, 1710-2700MHz Dual Band Combiner 7/16(f) EG 602 00961710-1880, 1920-2170MHz Dual Band Combiner 7/16(f) EG 100 9009

Dual Band Combiner TETRA / LTE80068 - 470 MHz / 791 - 862 MHz


This dual band combiner enables the connec-tion of 2 Radio Base Stations to the combiner:

1 TETRA Radio Base Station1 LTE800 Radio Base Station

The combiner combines the 2 signals to the antenna port, or splits the signal to the 2 RBSs in the receiving direction.


Reduces cost

By utilizing our dual band combiner you will reduce the cost of antennas, feeders and installation.



RevB

Technical Specifi cations for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband:Port 1: TETRAPort 2: LTE800

Insertion loss:Port 1: TETRAPort 2: LTE800


Max input power/port:Port 1: TETRAPort 2: LTE800Impedance in/out:


EG 602 0182

68 - 470 MHz791 - 862 MHz

< 0.3 dB < 0.5 dB

> 18.0 dB> 50 dB

150 W100 W50 Ohm

< -110 dBm (153 dBc)

Mechanical Specifi cations Dimensions (W x H x D):Connectors:Weight:

128 x 177 x 28 mm7/16 (f)2 kg

Environmental Specifi cations Temp. range (normal operation):Humidity:Sealing:

Egant reserves the right to change this product specifi cation at

any time without notice.


Dual Band Combiner TETRA / GSM90068 - 470 MHz / 870 - 970 MHz



1 TETRA Radio Base Station1 GSM900 Radio Base Station



Reduces cost



TETR

ATE

TRA

GSM

900

GSM

900

ANTANT


RevD

Technical Specifications for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:Passband: Port 1: TETRA Port 2: GSM900

Insertion loss: Port 1: TETRA Port 2: GSM900

Input return loss:Isolation between systems: Max input power/port:Port 1: TETRA Port 2: GSM900 Impedance in/out:


EG 100 9015 68 - 470 MHz 870 - 970 MHz

< 0.1 dB < 0.3 dB

> 18.0 dB> 50 dB

250 W250 W50 Ohm

< -110 dBm (153 dBc)

EG 100 9016 68 - 470 MHz 870 - 970 MHz

< 0.1 dB < 0.3 dB

> 18.0 dB> 50 dB

250 W250 W50 Ohm

< -110 dBm (153 dBc)

EG 100 9017

68 - 470 MHz870 - 970 MHz

< 0.1 dB< 0.3 dB

> 18.0 dB> 50 dB

250 W250 W50 Ohm

< -110 dBm (153 dBc) Mechanical Specifications Dimensions (W x H x D):Connectors:Weight:

128 x 177 x 28 mmN (f) 2 kg

128 x 177 x 28 mm7/16 (f) 2.6 kg

128 x 177 x 327/16 (f)2.8 kg


Egant reserves the right to change this product specification at





Dual Band Combiner68 - 500 MHz / 700 - 2700 MHz


This dual band combiner enables the connec-tion of 2 Radio Base Stations to the combiner.



Reduces cost




RevC


Electrical SpecificationsProduct number:Passband: Port 1: Low band Port 2: High band

Insertion loss: Port 1: Low band - ANT Port 2: High band - ANT

Input return loss:

Isolation between systems:Port 1: - ANT

Port 2: - ANT700 - 800 MHz800 - 2500 MHz2500 - 2700MHz Max input power/port:

Intermodulation: IM3, 2 x 43 dBm: Impedance in/out:

EG 602 0115 68 - 500 MHz 700 - 2700 MHz

< 0.3 dB, typ 0,15dB < 0.5 dB, typ 0.3dB

> 16.0 dB, typ 20dB

> 50 dB

> 40 dB> 50 dB> 30 dB

< 50 W < -150 dBc 50 Ohm

EG 602 0120 68 - 500 MHz 700 - 2700 MHz

< 0.3 dB, typ 0,15dB < 0.5 dB, typ 0.3dB

> 16.0 dB, typ 20dB

> 50 dB

> 40 dB> 50 dB> 30 dB

< 50W < -150 dBc 50 Ohm


235 x 35 x 130 mmN (f) 1.5 kg

235 x 20 x 130 mm7/16 (f) 1.0 kg



without notice.








Reduces cost



6868-- 5

00M

Hz

500M

Hz

ANT1ANT1

790

790 --

2700

MH

z27

00M

Hz


RevC




Input return loss:68 - 500 MHz

790 - 960 MHz1710 - 1880 MHz1920 - 2170 MHz2500 - 2700MHz

Isolation between systems:Port 1: - ANTPort 2: - ANT Max input power/port: Port 1: Low band Port 2: High band

Intermodulation: IM3, 2 x 43 dBm:

Impedance in/out:

EG 602 0072 68 - 500 MHz 790 - 2700 MHz

< 0.3 dB, typ 0.15dB< 0.4 dB, typ 0.15dB

> 18.0 dB

> 16.0 dB> 18.0 dB> 18.0 dB> 16.0 dB > 40 dB> 50 dB

< 300 W< 500 W <-110 dBm (153 dBc)

50 Ohm


265 x 55 x 120 mm7/16 (f) 1.5 kg



without notice.


Dual Band Combiner W-LAN376 - 2500 MHz TETRA, GSM900, GSM1800, UMTS, W-LAN

Add W-LAN to your antenna system

Installing the dual band combiner W-LAN enables you to add W-LAN to your cellular antenna system. After installning the W-LAN combiner and an access point you are up and running with a high speed W-LAN system.

This is a highly important feature when de-signing shared antenna systems wishing to add W-LAN capability to your system.

Save money

The dual band combiner W-LAN offers addi-tional benefits by opening up W-LAN capa-bility to your existing antenna system.

The sleek and easily installed combiner has a broad-banded spectrum with low insertion loss and low intermodulation.

W-LA

NW

-LAN

Access point

Access point

376-2500MHz

376-2170MH

z

W-LA

NW

-LAN

InjectorInjector

W-LA

NW

-LAN

Access point

Access point

376-2500MHz

376-2170MH

z

W-LA

NW

-LAN

InjectorInjector


RevC

Technical Specifications for Dual Band Combiner W-LANBelow are some typical data. For more detailed information, please contact us.


Input return loss:68 - 2170 MHz:2400 - 2500 MHz:

Insertion loss:Port 2 - Port 1 (ANT): 68 - 2170 MHz:Port 3 - Port 1 (ANT): 2400 - 2500 MHz:

Isolation: Port 2 - Port 3, Port 3 - Port 2

Max input power/port:

3rd order intermodulation:IM3, 2 x 43 dBm:

Impedance in/out:

EG 100 9018 376 - 2170 MHz 2400 - 2500 MHz

> 18 dB> 16 dB

< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)

> 50 dB

50 W avg. 0.5 kW peak

< - 97 dBm (140 dBc)

50 Ohm

EG 100 9028 376 - 2170 MHz 2400 - 2500 MHz

> 18 dB> 16 dB

< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)

> 50 dB


< - 97 dBm (140 dBc)

50 Ohm

EG 602 0007 68 - 2500 MHz 68 - 2170 MHz 2400 - 2500 MHz

> 18 dB> 16 dB

< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)

> 50 dB


< - 97 dBm (140 dBc)

50 Ohm


180 x 28 x 140 mmN (f) 1.6 kg

180 x 32 x 140 mm7/16 (f) 1.9 kg

180 x 32 x 140 mm7/16 (f), 7/16 (m), N (f) 1.9 kg

Environmental Specifications Temp. range (normal operation):Humidity: Sealing:


without notice.




Dual Band Combiner 80 - 240 MHz / 376 - 480 MHz

Combines FM + VHF + DAB and TETRAinto one antenna port

This dual band combiner enables the connec-tion of these two systems to the combiner:

1 FM + VHF + DAB Input1 TETRA Radio Base Station

The combiner combines the two signals intoone antenna port, or splits the signal into the two input systems in the receiving direction.

Reduces cost


It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the inputs into the com-biner it will immediately render you all the benefi ts of antenna sharing.


RevB

Technical Specifi cations for the FM + VHF + DAB / TETRA Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband:Port 1: FM + VHF + DABPort 2: TETRA

Insertion loss:

Input return loss:

Isolation between systems:


Impedance in/out:

DC-Bypass

EG 602 0183

80 - 240 MHz376 - 480 MHz

< 0.5 dB

> 16.0 dB

> 50 dB

< 40 W

50 Ohm

Port 1 - Ant

EG 602 0184

80 - 240 MHz376 - 480 MHz

< 0.5 dB

> 16.0 dB

> 50 dB

< 40 W

50 Ohm

Port 1 - Ant

Mechanical & Environmental Specifi cations Dimensions (W x H x D):Connectors:Weight:Sealing:

95 x 23 x 75 mmN (f)0.5 kgIP65

95 x 23 x 75 mmN (f)0.5 kgIndoor use

Egant reserves the right to change this product specifi cation at


Dual Band Combiner FM + VHF + DAB / TETRA 80 - 240 MHz / 376 - 480 MHz

Combines FM + VHF + DAB and TETRAinto one antenna port

This dual band combiner enables the connec-tion of these two systems to the combiner:

1 FM + VHF + DAB Input1 TETRA Radio Base Station

The combiner combines the two signals intoone antenna port, or splits the signal into the two input systems in the receiving direction.

Reduces cost


It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the inputs into the com-biner it will immediately render you all the benefi ts of antenna sharing.


RevF

Technical Specifi cations for the FM + VHF + DAB / TETRA Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband:Port 1: FM + VHF + DABPort 2: TETRA

Insertion loss:Port 1: 80 - 108 MHzPort 1: 108 - 174 MHzPort 1: 174 - 240 MHzPort 2: TETRA

Input return loss:

Isolation between systems: Port 1 - 2: 80 - 108 MHz, 108 - 240 MHz Port 2 - 1: 376 - 480 MHz

Max input power/port:Port 1: Port 2:Impedance in/out:DC-Bypass

EG 602 0030

80 - 240 MHz376 - 480 MHz

< 0.5 dB < 0.5 dB< 0.5 dB< 0.5 dB

> 18.0 dB

> 40 dB> 40 dB

> 20 W> 20 W50 Ohm Port1 - Ant

EG 602 0038

80 - 240 MHz376 - 480 MHz

< 0.5 dB < 0.5 dB< 0.5 dB< 0.5 dB

> 18.0 dB

> 40 dB> 40 dB

> 20 W> 20 W50 Ohm Port1 - Ant

Mechanical & Environmental Specifi cations Dimensions (W x H x D):Connectors:Weight:Sealing:

Egant reserves the right to change this product specifi cation at any time without notice.

118 x 119 x 37 mm7/16 (f)1.7 kgIP67

110 x 115 x 37 mm7/16 (f)1.4 kgIndoor use

Dual Band Combiner80- 960 MHz / 1710 - 2700 MHz





Reduces cost



8080-- 9

60960

GSM

1800

GSM

1800

UM

TSU

MTS

LTE

LTE

ANTANT

8080-- 9

60960

GSM

1800

GSM

1800

UM

TSU

MTS

LTE

LTE

ANTANT


Rev D



Insertion loss: Port 1: 80 - 960 MHz- ANT Port 2: 1710 - 2700 MHz - ANT

Input return loss:80 - 960 MHz1710 - 2700 MHz

Isolation between systems:

Intermodulation: IM3, 2x43 dBm:

DC by pass Port 1 - Ant Max input power/port: Port 1: Low band Port 2: High band

Impedance in/out:

Single UnitEG 602 0108 80 - 960 MHz 1710 - 2700 MHz

< 0.3 dB (0,2 dB typical) < 0.5 dB (0,3 dB typical)

> 18.0 dB> 18.0 dB

> 50 dB

<-150 dBc

2A max

< 60 W< 60 W 50 Ohm

Double UnitEG 602 0109 80 - 960 MHz 1710 - 2700 MHz

< 0.3 dB (0,2 dB typical) < 0.5 dB (0,3 dB typical)

> 18.0 dB> 18.0 dB

> 50 dB

<-150 dBc

2A max

< 60 W< 60 W 50 Ohm


125 x 32 x 110 mm7/16 (f) 1.5 kg

125 x 68 x 110 mm7/16 (f) 3.2 kg



without notice.



Dual Band Combiner155 - 500 MHz / GPS


RevB





1575 - 1576 MHz

Isolation between systems:Port 1: - Port2Port 2: - Port1 Max input power/port: Port 1: Low band Port 2: High band

Intermodulation: IM3, 2 x 43 dBm: DC by-pass Port 2 - ANT

Impedance in/out:

EG 602 0049

155 - 500 MHz 1575 - 1576 MHz

< 0.2 dB < 0.2 dB

> 16.0 dB> 20.0 dB

> 16.0 dB

> 50 dB> 50 dB

< 300 W< 20 W < -110 dBm (153 dBc)1A, max 50 Ohm


265 x 55 x 120 mm7/16 (f) 1.5 kg



without notice.







Reduces cost



TETR

ATE

TRA

UM

TSU

MTS

ANTANT


RevD


Electrical SpecificationsProduct number:Passband:Port 1: Low bandPort 2: High band

Insertion loss:Port 1: Low band - ANTPort 2: High band - ANT



Intermodulation: IM3, 2 x 43 dBm: DC by-pass Port 2: UMTS - ANT

Impedance in/out:

EG 602 0045 376 - 500 MHz 1920 - 2170 MHz

< 0.3 dB < 0.3 dB

> 18.0 dB > 18.0 dB

> 30 dB> 50 dB

< 300 W< 500 W <-110 dBm (153 dBc)1A, max 50 Ohm

EG 602 0046 376 - 500 MHz 1920 - 2170 MHz

< 0.3 dB < 0.3 dB

> 18.0 dB> 18.0 dB

> 30 dB> 50 dB

< 300 W< 500 W <-110 dBm (153 dBc)1A, max 50 Ohm


242 x 31 x 84 mmN (f) 1.5 kg

242 x 31 x 84 mm7/16 (f) 1.5 kg



without notice.



Dual Band Combiner W-LAN376 - 2500 MHz TETRA, GSM900, GSM1800, UMTS, W-LAN

Add W-LAN to your antenna system

Installing the dual band combiner W-LAN enables you to add W-LAN to your cellular antenna system. After installning the W-LAN combiner and an access point you are up and running with a high speed W-LAN system.

This is a highly important feature when de-signing shared antenna systems wishing to add W-LAN capability to your system.

Save money

The dual band combiner W-LAN offers addi-tional benefits by opening up W-LAN capa-bility to your existing antenna system.

The sleek and easily installed combiner has a broad-banded spectrum with low insertion loss and low intermodulation.

W-LA

NW

-LAN

Access point

Access point

376-2500MHz

376-2170MH

z

W-LA

NW

-LAN

InjectorInjector

W-LA

NW

-LAN

Access point

Access point

376-2500MHz

376-2170MH

z

W-LA

NW

-LAN

InjectorInjector


RevC

Technical Specifications for Dual Band Combiner W-LANBelow are some typical data. For more detailed information, please contact us.


Input return loss:68 - 2170 MHz:2400 - 2500 MHz:

Insertion loss:Port 2 - Port 1 (ANT): 68 - 2170 MHz:Port 3 - Port 1 (ANT): 2400 - 2500 MHz:

Isolation: Port 2 - Port 3, Port 3 - Port 2


3rd order intermodulation:IM3, 2 x 43 dBm:

Impedance in/out:

EG 100 9018 376 - 2170 MHz 2400 - 2500 MHz

> 18 dB> 16 dB

< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)

> 50 dB


< - 97 dBm (140 dBc)

50 Ohm

EG 100 9028 376 - 2170 MHz 2400 - 2500 MHz

> 18 dB> 16 dB

< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)

> 50 dB


< - 97 dBm (140 dBc)

50 Ohm

EG 602 0007 68 - 2500 MHz 68 - 2170 MHz 2400 - 2500 MHz

> 18 dB> 16 dB

< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)

> 50 dB


< - 97 dBm (140 dBc)

50 Ohm


180 x 28 x 140 mmN (f) 1.6 kg

180 x 32 x 140 mm7/16 (f) 1.9 kg

180 x 32 x 140 mm7/16 (f), 7/16 (m), N (f) 1.9 kg



without notice.




Dual Band CombinerUMTS/LTE376-2170MHz / 2500-2690 MHz





Reduces cost




RevE




Input return loss:1920- 2170 MHz2500 - 2690 MHz


Intermodulation: IM3, 2 x 43 dBm:

Impedance in/out:

EG 602 0074 376 - 2170 MHz 2500 - 2690 MHz

< 0.3 dB, typ <0.15 dB< 0.3 dB, typ <0.15 dB

> 18.0 dB> 18.0 dB

> 50 dB> 50 dB

< 400 W< 100 W <-140 dBc

50 Ohm

EG 602 0076 376 - 2170 MHz 2500 - 2690 MHz

< 0.3 dB, typ <0.15 dB< 0.5 dB, typ <0.25 dB

> 17.5 dB> 17.5 dB

> 50 dB> 50 dB

< 60 W< 60 W

<-140 dBc

50 Ohm


265 x 55 x 120 mm7/16 (f) 1.5 kg

140 x 35 x 138 mmN (f)1.2 kg



without notice.



Dual Band Combiner 380 - 395 MHz / 410 - 425 MHzTETRA Public SafetyTETRA Public Services


This Dual Band Combiner enables the connec-tion of 2 Radio Base Stations to the combiner:

1 TETRA Public Safety System1 TETRA Public Services System

The Combiner combines the 2 signals to 1 antenna port, or splits the signal to the 2 RBSs in the receiving direction.


Reduces cost

By utilizing the Egant Dual Band Combiner you will reduce the cost of antennas, feeders and installation.

It eliminates the cost inefficient need to to make one antenna installation for each sys-tem. By simply connecting the RBSs into the combiner it will immediately render you all the benefits of antenna sharing.


RevC


Electrical SpecificationsProduct number: Passband: Port 1: TETRA - Public Safety Port 2: TETRA - Public Services

Insertion loss: Port 1: TETRA - Public Safety Port 2: TETRA - Public Services

Input return loss:Isolation between systems: Max input power/port: Port 1: TETRA - Public Safety Port 2: TETRA - Public Services

Impedance in/out:


EG 602 0023 380 - 395 MHz 410 - 425 MHz

< 1.2 dB < 1.2 dB

> 18.0 dB> 50 dB

< 60W< 60W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0024 380 - 395 MHz 410 - 425 MHz

< 1.2 dB < 1.2 dB

> 18.0 dB> 50 dB

< 60W< 60W

50 Ohm

<-110 dBm (153 dBc)


150 x 150 x 110 mmN (f) 2.5 kg

150 x 150 x 110 mm7/16 (f) 2.5 kg

Environmental Specifications Temp. range (normal operation):Sealing:


without notice.

-40 to +70º C Indoor








Reduces cost


It eliminates the cost ineffi cient need to to make one antenna installation for each sys-tem. By simply connecting the RBSs into the combiner it will immediately render you all the benefi ts of antenna sharing.


RevA


Electrical Specifi cationsProduct number: Passband:Port 1: Port 2:

Insertion loss:



Impedance in/out:


EG 602 0191

380 - 395 MHz440 - 450 MHz

< 1.4 dB, (Typ 0.8dB)

> 18.0 dB> 50 dB

< 60W

50 Ohm

< -110 dBm (153 dBc)


150 x 150 x 110 mm7/16 (f)2.5 kg

Environmental Specifi cationsTemp. range (normal operation):Sealing:


without notice.

-20 to +55º CIndoor

Dual Band Combiner 380 - 395 MHz442,975 - 448,975 MHz






Reduces cost



Egant ABBox 945SE-114 79 Stockholm SwedenPhone: +46 (0)8 620 06 50E-mail: [email protected]

RevB


Electrical SpecificationsProduct number: Passband: Port 1: Port 2: Insertion loss: Port 1: Port 2: TETRA


Impedance in/out:


EG 602 0176 380 - 395 MHz 442,975 - 448,975 MHz

< 1.2 dB, (Typ 0.7dB) < 1.2 dB, (Typ 0.7dB)

> 16.0 dB> 40 dB

< 60W< 60W

50 Ohm

< -110 dBm (153 dBc)


150 x 150 x 110 mmN (f) 2.5 kg



without notice.








Reduces cost




RevD


Electrical SpecificationsProduct number: Passband: Port 1: TETRA - Public Safety Port 2: TETRA - Public Services

Insertion loss: Port 1: TETRA - Public Safety Port 2: TETRA - Public Services


Impedance in/out:


EG 602 0094 380 - 395 MHz 450 - 470 MHz

< 1.2 dB, (Typ 0.7dB) < 1.2 dB, (Typ 0.7dB)

> 18.0 dB> 50 dB

< 60W< 60W

50 Ohm

< -110 dBm (153 dBc)


150 x 150 x 110 mmN (f) 2.5 kg



without notice.


Dual Band Combiner 790 - 862 MHz / 880 - 960 MHz



1 LTE 800 Radio Base Station1 GSM900 Radio Base Station



Reduces cost




RevD


Electrical SpecificationsProduct number:Passband: Port 1: DVB Port 2: GSM900

Insertion loss: Port 1: DVB Port 2: GSM900

Input return loss:Isolation between systems: Max input power/port:Port 1: DVB Port 2: GSM900 Impedance in/out:


EG 602 0097 790 - 862 MHz 880 - 960 MHz

< 0.45 dB, typ 0.2dB< 0.45 dB, typ 0.2dB

> 18.0 dB> 50 dB

200 W200 W50 Ohm

<-110 dBm (153 dBc)

EG 602 0112 790 - 862 MHz 880 - 960 MHz

< 0.45 dB, typ 0.2dB< 0.45 dB, typ 0.2dB

> 18.0 dB> 50 dB

200 W200 W50 Ohm

<-110 dBm (153 dBc)

Mechanical Specifications Dimensions (W x H x D):Connectors:Weight:

200 x 60 x 185 mm7/16 (f) 3.2 kg

200 x 60 x 185 mmN (f) 3.1 kg


Egant reserves the right to change this product specification at




Dual Band Combiner 790 - 1000 MHz, 1710 - 2170 MHz



1 800/900 Radio Base Station1 1800/2100 Radio Base Station



Reduces cost


It eliminates the cost ineffi cient need to to make one antenna installation for each sys-tem. By simply connecting the RBSs into the combiner it will immediately render you all the benefi ts of antenna sharing.

GSM

900

GSM

900

GSM

1800

GSM

1800

UM

TSU

MTS

ANTANT


RevB


Electrical Specifi cationsProduct number: Passband:Port 1: 800/900Port 2: 1800/2100

Insertion loss:Port 1: 800/900Port 2: 1800/2100


Max input power/port:Port 1: 800/900Port 2: 1800/2100

Impedance in/out:


EG 602 0110

790 - 1000 MHz1710 - 2170 MHz

< 0.3dB, typ 0.15dB < 0.5dB, typ 0.25dB

> 18.0 dB> 50 dB

< 250W< 150W

50 Ohm

< -117 dBm (160 dBc)


117 x 215 x 50 mm7/16 (f)1.5 kg



without notice.


Dual Band Combiner 800 - 1000 MHz, 1700 - 2170 MHz



1 GSM800 / GSM900 Radio Base Station1 CDMA / GSM1800 Radio Base Station or1 GSM1900 / UMTS Radio Base Station



Reduces cost



GSM

900

GSM

900

GSM

1800

GSM

1800

UM

TSU

MTS

ANTANT


RevE


Electrical SpecificationsProduct number: Passband: Port 1: GSM800 / GSM900 / CDMA Port 2: GSM1800 / GSM1900 / UMTS

Insertion loss: Port 1: GSM800 / GSM900 / CDMA Port 2: GSM1800 / GSM1900 / UMTS

Input return loss:Isolation between systems: Max input power/port: Port 1: GSM800 / GSM900 / CDMA Port 2: GSM1800 / GSM1900 / UMTS

Impedance in/out:


EG 100 9013 800 - 1000 MHz 1700 - 2170 MHz

< 0.15 dB < 0.25 dB

> 21.0 dB> 50 dB

< 250W< 150W

50 Ohm

< -110 dBm (153 dBc)

EG 100 9014 800 - 1000 MHz 1700 - 2170 MHz

< 015 dB < 0.25 dB

> 21.0 dB> 50 dB

< 250W< 150W

50 Ohm

< -110 dBm (153 dBc)


117 x 215 x 50 mm7/16 (f) 1.5 kg

117 x 215 x 50 mmN (f) 1.5 kg



without notice.



Dual Band CombinerGSM900, GSM1800



1 GSM900 Radio Base Station1 GSM1800 Radio Base Station



Reduces cost

By utilizing the Egant dual band combiner you will reduce the cost of antennas, feeders and installation.



Rev P1B


Electrical SpecificationsProduct number:Passband: Port 1: GSM900 Port 2: GSM1800

Insertion loss: Port 1: GSM900 - ANT Port 2: GSM1800 - ANT

Input return loss:Isolation between systems:Rejection 1920 - 2170 MHz (UMTS): Max input power/port: Port 1: GSM900 Port 2: GSM1800

Impedance in/out:

EG 602 0034 880 - 960 MHz 1710 - 1880 MHz

< 0.2 dB (0.1 dB typ)< 0.4 dB (0.2 dB typ)

> 18.0 dB> 50 dB> 65.0 dB

100 W100 W

50 Ohm


195 x 185 x 55 mm7/16 (f) 4 kg



without notice.


Dual Band Combiner890-960 MHz / 1710-1880, 1920-2170, 2600-2700MHz MHz





Reduces cost




RevC




Input return loss: Isolation between systems: Max input power/port: Port 1: Low band Port 2: High band

Intermodulation: IM3, 2 x 43 dBm: DC by-pass Port 2: UMTS - ANT

Impedance in/out:

EG 602 0096 890 - 960 MHz 1710 - 1880 MHz 1920 - 2170 MHz 2600- 2700 MHz

< 0.3 dB, typ 0,15dB < 0.4dB, typ 0,15dB

> 16.0 dB > 50 dB

< 150 W< 150 W < -110 dBm (153 dBc)1A, max 50 Ohm


265 x 55 x 120 mm7/16 (f) 2.5 kg



without notice.


Triple Band Combiner/Dual Band Combiner UMTS, GSM1800, GSM900 / GSM1800, UMTS






Reduces cost



Dual Band Combiner - combines 2 RBSs into 1 antenna port

The dual band combiner enables you to connect 2 Radio Base Stations to the combiner:

1 GSM1800 Radio Base Station1 UMTS Radio Base Station

GSM

900

GSM

900

GSM

180

0G

SM 1

800

UM

TSU

MTS

ANTANT


RevF

Technical Specifi cations for the Triple Band Combiner/Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband:Port 1: GSM900Port 2: GSM1800Port 3: UMTS

Insertion loss:Port 1: GSM900 - ANTPort 2: GSM1800 - ANTPort 3: UMTS - ANT


Max input power/port:Port 1: GSM900Port 2: GSM1800Port 3: UMTS

Impedance in/out:



EG 100 9012

698 - 960 MHz1710 - 1880 MHz1920 - 2170 MHz

< 0.20 dB < 0.30 dB < 0.45 dB

> 21.0 dB> 50 dB

< 200 W< 200 W< 100 W

50 Ohm

<-110 dBm (153 dBc)

1A, max, per input

EG 100 9009

1710 - 1880 MHz1920 - 2170 MHz

< 0.40 dB < 0.45 dB

> 20.0 dB> 50 dB

< 200 W< 100 W

50 Ohm

<-110 dBm (153dBc)

1A, max, per input


230 x 200 x 555 mm7/16 (f)3.6 kg

245 x 210 x 50 mm7/16 (f)3.6 kg



without notice.



Duplex Filter www.egant.se

Frequency range Description Connector Ordering numberDuplex Filter 380-385, 390-395MHz Duplex Filter Tetra N(f) EG 602 0084380-385, 390-395MHz Duplex Filter Tetra 7/16(f) EG 602 0020380-385, 390-395MHz Duplex Filter Tetra 7/16(f) EG 602 0021415-420, 425-430MHz Duplex Filter Tetra SMA(f) EG 602 0037791-821, 832-862MHz Duplex Filter 800 7/16(f) EG 602 0192876-880, 921-925MHz Duplex GSM-R 7/16(f) EG 602 0148876-880, 921-925MHz Duplex GSM-R N(f) EG 602 0149880-915, 925-960MHz Duplex Filter 900 N(f) EG 602 0079880-915, 925-960MHz Duplex Filter 900 SMA(f) EG 602 0087880-915, 925-960MHz Duplex Filter 900 7/16(f) EG 602 0091890-915, 935-960MHz Duplex Filter 900 7/16(f) EG 602 0090890-915, 935-960MHz Duplex Filter 900 N(f) EG 602 0088890-915, 935-960MHz Duplex Filter 900 SMA(f) EG 602 0089890-915, 935-960MHz Duplex Filter 900 7/16(f) EG 602 00901710-1785, 1805-1880MHz Duplex Filter 1800 N(f) EG 602 00551710-1785, 1805-1880MHz Duplex Filter 1800 7/16(f) EG 602 01931920-1980, 2110-2170MHz Duplex Filter 2100 N(f) EG 602 00561920-1980, 2110-2170MHz Duplex Filter 2100 7/16(f) EG 602 01711920-1980, 2110-2170MHz Duplex Filter 2100 7/16(f) EG 602 01942500-2570, 2620-2690MHz Duplex Filter 2600 N(f) EG 602 01042500-2570, 2620-2690MHz Duplex Filter 2600 7/16(f) EG 602 01952500-2570, 2620-2690MHz Duplex Filter 2600 7/16(f) EG 602 01032500-2570, 2620-2690MHz Duplex Filter 2600 N(f) EG 602 01042500-2570, 2620-2690MHz Duplex Filter 2600 SMA(f) EG 602 01052500-2570, 2620-2690MHz Duplex Filter 2600 N(f) EG 602 0106

Duplexer TETRA380 - 385 MHz390 - 395 MHz

This Duplexer combines/splits the TETRA TX and RX signals to or from one common TX/RX antenna.


Rev C

Technical Specifications for TETRA DuplexersBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number: Passband: Port 1: RX Port 2: TX

Insertion loss:

Input return loss:Isolation between TX/RX: Max input power/port:

Impedance in/out:


Monitoring port:

EG 602 0084 380 - 385 MHz 390 - 395 MHz

< 1.7 dB

> 18.0 dB> 65 dB

200 W

50 Ohm

< -110 dBm (153 dBc)


100 x 150 x 100 mmN (f) 1.4 kg


Egant reserves the right to change this product

specification at any time without notice.

-40 to +70º CRelative 5 - 100% Indoor use

Duplexer TETRA380 - 385 MHz390 - 395 MHz415 - 420 MHz425 - 430 MHz

This Duplexer combines/splits the TETRA TX and RX signals to or from one common TX/RX antenna.

Egant Cellular ComponentsBox 945SE-114 79 Stockholm SwedenPhone: +46 (0)8 620 06 50 E-mail: [email protected]

RevC

Technical Specifications for TETRA DuplexersBelow are some typical data. For more detailed information, please contact us.


Insertion loss:


Impedance in/out:


Monitoring port:

EG 602 0020 380 - 385 MHz 390 - 395 MHz

< 1.5 dB

> 20.0 dB> 65 dB

200 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0021 380 - 385 MHz 390 - 395 MHz

< 0.8 dB

> 20.0 dB> 65 dB

200 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0037

415 - 420 MHz425 - 430 MHz

< 1.9 dB (1.2 typ)

> 20.0 dB> 75 dB

80 W

50 Ohm

<-110 dBm (153 dBc)

20 dB


100 x 150 x 100 mm7/16 (f) 1.4 kg

100 x 250 x 300 mm7/16 (f) 4.2 kg

240 x 240 x 80 mmSMA3 kg







LTE 800 Duplexer791 - 821MHz 832 - 862MHz

This Duplexer combines/splits the LTE800 TX and RX signals to or from one common TX/RX antenna.


RevA

Technical Specifications for LTE800 DuplexersBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:Passband: (To be configured for customers needs)

Port 1: TXPort 2: RX

Insertion loss:


Impedance in/out:

EG 602 0192 791 - 821MHz 832 - 862MHz

< 1.0 dB, typ 0.6dB

> 18.0 dB> 50 dB

100 W

50 Ohm


175 x 45 x 155 mm7/16 (f) 1.8 kg





Duplexer GSM-R876 - 880 MHz921 - 925 MHz

This Duplexer combines/splits the GSM-R TX and RX signals to or from one common TX/RX antenna.


Rev B

Technical Specifications for GSM-R DuplexersBelow are some typical data. For more detailed information, please contact us.


Insertion loss:


Impedance in/out:


EG 602 0148 876 - 880 MHz 921 - 925 MHz

< 0.5 dB, typ 0.3dB

> 18.0 dB> 85 dB

250 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0149 876 - 880 MHz 921 - 925 MHz

< 0.5 dB, typ 0.3dB

> 18.0 dB> 85 dB

250 W

50 Ohm

<-110 dBm (153 dBc)


160 x 55 x 120 mm7/16 (f) 2.5 kg

160 x 55 x 120 mmN (f) 2.5 kg






Duplexer EGSM900880 - 915 MHz925 - 960 MHz

This Duplexer combines/splits the EGSM900 TX and RX signals to or from one common TX/RX antenna.


RevD

Technical Specifications for EGSM900 DuplexersBelow are some typical data. For more detailed information, please contact us.


Insertion loss: Port 1: RX Port 2: TX


Impedance in/out:


EG 602 0079 880 - 915 MHz 925 - 960 MHz

< 0.9 dB, typ 0.5dB< 1.1 dB, typ 0.5dB

> 18.0 dB> 50 dB

200 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0087 880 - 915 MHz 925 - 960 MHz

< 0.9 dB, typ 0.5dB< 1.1 dB, typ 0.5dB

> 18.0 dB> 50 dB

200 W

50 Ohm <-110 dBm (153 dBc)

EG 602 0091 880 - 915 MHz 925 - 960 MHz

< 0.9 dB, typ 0.5dB< 1.1 dB, typ 0.5dB

> 18.0 dB> 50 dB

200 W

50 Ohm <-110 dBm (153 dBc)


180 x 60 x 110 mmN (f) 1.5 kg

180 x 60 x 100 mmSMA (f) 1.5 kg

180 x 60 x 130 mm7/16 (f) 1.6 kg







Duplexer GSM900890 - 915 MHz935 - 960 MHz

This Duplexer combines/splits the GSM900 TX and RX signals to or from one common TX/RX antenna.


Rev C

Technical Specifications for GSM900 DuplexersBelow are some typical data. For more detailed information, please contact us.


Insertion loss:


Impedance in/out:


EG 602 0088 890 - 915 MHz 935 - 960 MHz

< 0.7 dB, typ 0.5dB

> 18.0 dB> 60 dB

200 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0089 890 - 915 MHz 935 - 960 MHz

< 0.7 dB, typ 0.5dB

> 18.0 dB> 60 dB

200 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0090 890 - 915 MHz 935 - 960 MHz

< 0.7 dB, typ 0.5dB

> 18.0 dB> 60 dB

200 W

50 Ohm

<-110 dBm (153 dBc)


180 x 60 x 110 mmN (f) 1.5 kg

180 x 60 x 100 mmSMA (f) 1.5 kg

180 x 60 x 130 mm7/16 (f) 1.6 kg







Duplexer1710 - 1785MHz, 1805 - 1880MHz1920 - 1980MHz, 2110 - 2170MHz

This Duplexer combines/splits the GSM1800 or UMTS TX and RX signals to or from one com-mon TX/RX antenna.


RevD

Technical Specifications for GSM1800, UMTS DuplexersBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:Passband: (To be configured for customers needs)

Port 1: RXPort 2: TX

Insertion loss:


Impedance in/out:

EG 602 0055 1710 - 1785MHz 1805 - 1880MHz

< 1.2 dB, typ 0.6dB

> 18.0 dB> 75 dB, typ 90dB

100 W

50 Ohm

EG 602 0056 1920 - 1980MHz2110 - 2170MHz

< 1.2 dB, typ 0.6dB

> 18.0 dB> 75 dB, typ 90dB

100 W

50 Ohm

EG 602 0171 1920 - 1980MHz2110 - 2170MHz

< 1.2 dB, typ 0.6dB

> 18.0 dB> 75 dB, typ 90dB

100 W

50 Ohm


145 x 45 x 145 mmN (f) 0.9. kg

145 x 45 x 145 mmN (f) 0.9 kg

145 x 45 x 145 mm7/16 (f) 0.9 kg




0 to +70º CRelative 5 - 100% Indoor use



Duplexer1710 - 1785MHz, 1805 - 1880MHz1920 - 1980MHz, 2110 - 2170MHz2500 - 2570MHz, 2620 - 2690MHz

This Duplexer combines/splits the GSM1800, UMTS or LTE2600 TX and RX signals to or from one common TX/RX antenna.


RevA

Technical Specifi cations for GSM1800, UMTS2100, LTE2600 DuplexersBelow are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband: (To be confi gured for customers needs)

Port 1: RXPort 2: TX

Insertion loss:

Input return loss:Isolation between TX/RX:


Impedance in/out:

EG 602 0193

1710 - 1785MHz1805 - 1880MHz

< 1.0 dB, typ 0.6dB

> 18.0 dB> 50 dB

100 W

50 Ohm

EG 602 0194

1920 - 1980MHz2110 - 2170MHz

< 0.8 dB, typ 0.5dB

> 18.0 dB> 50 dB, typ 60dB

100 W

50 Ohm

EG 602 0195

2500 - 2570MHz2620 - 2690MHz

< 0.7 dB, typ 0.4dB

> 18.0 dB> 60 dB, typ 70dB

100 W

50 Ohm


175 x 45 x 155 mm7/16 (f)1.8 kg

175 x 40 x 155 mm7/16 (f)1.5 kg

175 x 45 x 155 mm7/16 (f)1.5 kg



specifi cation at any time without notice.

-20 to +55º CRelative 5 - 100%Indoor use



Duplexer LTE2500-2570MHz2620-2690MHz

This Duplexer combines/splits the LTE TX and RX signals to or from one common TX/RX antenna.


Rev C

Technical Specifications for LTE DuplexersBelow are some typical data. For more detailed information, please contact us.


Insertion loss:

Input return loss:

Isolation between TX/RX:


Impedance in/out:


EG 602 0103 2500-2570MHz 2620-2690MHz

< 0.7 dB, typ 0,3dB

> 18.0 dB

> 60 dB, typ 70dB

200 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0104 2500-2570MHz 2620-2690MHz

< 0.7 dB, typ 0.3dB

> 18.0 dB

> 60 dB, typ 70dB

200 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0105 2500-2570MHz 2620-2690MHz

< 0.9 dB, typ 0.6dB

> 18.0 dB

> 75 dB, typ 85dB

200 W

50 Ohm

<-110 dBm (153 dBc)

EG 602 0106 2500-2570MHz 2620-2690MHz

< 0.9 dB, typ 0.6dB

> 18.0 dB

> 75 dB, typ 85dB

200 W

50 Ohm

<-110 dBm (153 dBc)


176 x 38 x 115 mmSMA (f) 1.5 Kg

176 x 38 x 115 mmN (f) 1.5 Kg

200 x 45 x 140 mmSMA (f) 2.8 Kg

200 x 45 x 140 mmN (f) 2.8 Kg




-30 to +70º C

Relative 5 - 100% Indoor use

-30 to +70º C


-30 to +70º C


-30 to +70º C


Band Pass Filter www.egant.se

Frequency range Description Connector Ordering numberBand Pass Filters380-395MHz Band Pass Filter Tetra, reject 403-2170 7/16(f) EG 602 0181880-960MHz Band Pass Filter 900, reject 0-850, 990-6000 7/16(f) EG 602 0152880-960MHz Band Pass Filter 900, reject 0-889 7/16(f) EG 602 0142890-960MHz Band Pass Filter 900, reject 0-888 7/16(f) EG 602 0169880-960MHz Band Pass Filter 900, reject 0-888,5 7/16(m)-7/16(f) EG 601 0198890-960MHz Band Pass Filter 900, reject 0-888,5 7/16(m)-7/16(f) EG 601 0199890-960MHz Band Pass Filter 900, reject 1920-2170 7/16(f) EG 602 00311710-1880MHz Band Pass Filter 1800, reject 1920-2170 7/16(f) EG 602 00321920-2170MHz Band Pass Filter 2100, reject< 1900, > 2190 7/16(f) EG 602 01701935-1965, 2125-2155MHz Band Pass Filter 2100, reject 1970-2000 7/16(m)-7/16(f) EG 602 02011950-1965, 2140-2155MHz Band Pass Filter 2100, reject 1970-2000 7/16(m)-7/16(f) EG 602 0200

Band Pass FilterTetra 380 - 395 MHzGSM900 880 - 960 MHzUMTS2100 1920 - 2170 MHz


RevD

Technical Specifi cations for TETRA, GMS900, UMTS2100 Band Pass FilterBelow are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number: Passband:Reject Band:

Insertion loss:

Input return loss:

Attenuation in reject band:Reject Band: 0 -340 MHzReject Band: 403 -1920 MHzReject Band: 1920 - 3GHzReject Band: 0GHz - 850MHzReject Band: 990MHz - 3GHzReject Band: 0GHz - 1850MHzReject Band: 2250 - 3GHzReject Band: 3GHz - 6GHzReject Band: 6GHz - 10GHzReject Band: 10GHz - 18GHz


Impedance in/out:

EG 602 0181380 - 395 MHz403 - 2170MHz

< 2.4 dB, typ 1,5dB

> 16.0 dB

> 60 dB> 60 dB> 70 dB

> 70dB> 50dB> 20dB

100 W

50 Ohm

EG 602 0152880 - 960 MHz0 - 850MHz990 - 6000GHz

< 1.8 dB, typ 0,8dB

> 16.0 dB

> 70dB> 70dB

> 70dB> 50dB> 20dB

100 W

50 Ohm

EG 602 01531920 - 2170 MHz0 - 1850MHz2250 - 6000MHz

< 1.8 dB, typ 0,7dB

> 16.0 dB

> 70dB> 70dB> 70dB> 50dB> 20dB

100 W

50 Ohm


140 x 75 x 75 mm7/16 (f)1.5 kg

175 x 45 x 165 mm7/16 (f)1.8 kg

175 x 45 x 165 mm7/16 (f)1.8kg



specifi cation at any time without notice.




Band Pass FilterGSM900 890 - 960 MHzStop band: 0-889MHz

Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]

RevB

Technical Specifi cations for the Band Pass Filter GSM900Below are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband:Stop bandInsertion loss:890 - 891 MHz891 - 892 MHz892 - 893 MHz893 - 905 MHz905 - 960 MHz

Input return loss:

Attenuation in rejection band:0 - 869 MHz869 - 889 MHz


Impedance in/out:


EG 602 0142890 - 960 MHz0 - 889 MHz

< 4 dB < 2.5 dB < 1.0 dB < 0.6 dB < 0.3 dB > 17.5 dB

> 50 dB> 30 dB

400 W

50 Ohm

< -110 dBm

EG 602 0147890 - 960 MHz0 - 889 MHz

< 4 dB < 2.5 dB < 1.0 dB < 0.6 dB < 0.3 dB

> 17.5 dB

> 50 dB> 30 dB

400 W

50 Ohm

< -110 dBm


300 x 72 x 95 mm7/16 (f)2.5 kg

310 x 82 x 105 mm7/16 (f)3.4 kg



without notice.

0 to + 40º CIP50

-20 to + 55º CIP65

Band Pass FilterGSM900 890 - 960 MHzStop band: 0-888MHz


RevA


Electrical Specifi cationsProduct number:Passband:Stop bandInsertion loss:890 - 892 MHz892 - 893 MHz893 - 905 MHz905 - 960 MHz

Input return loss:

Attenuation in rejection band:0 - 880 MHz880 - 885 MHz885 - 888 MHz


Impedance in/out:


EG 602 0169890 - 960 MHz0 - 888 MHz

< 1.5 dB < 0.8 dB < 0.6 dB < 0.3 dB

> 17.5 dB

> 50 dB> 40 dB> 30 dB

400 W

50 Ohm

< -110 dBm, (153 dBc)


300 x 72 x 95 mm7/16 (f)2.5 kg



without notice.

-35 to + 65º CIP66

Band Pass FilterGSM900 890 - 960 MHzStop band: 0-888.5MHz


RevA


Electrical Specifi cationsProduct number:Passband:Stop band

Insertion loss:890 - 892 MHz892 - 893 MHz893 - 960 MHz

Input return loss:

Attenuation in rejection band:0 - 888.5 MHz


Impedance in/out:


EG 602 0198890 - 960 MHz0 - 888.5 MHz

< 4.0 dB < 2.0 dB < 1.0 dB, typ 0,4 dB > 18 dB, typ 22 dB

> 50 dB

200 W

50 Ohm

< -110 dBm, (153 dBc)

EG 602 0199890 - 960 MHz0 - 888.5 MHz

< 4.0 dB < 2.0 dB < 1.0 dB, typ 0,4 dB > 18 dB, typ 22 dB

> 50 dB

200 W

50 Ohm

< -110 dBm, (153 dBc)


300 x 60 x 180 mm7/16 (f) - 7/16(m)2.5 kg

320 x 72 x 200 mm7/16 (f) - 7/16(m)3.0 kg



without notice.

+5 to + 45º CIndoor

-30 to + 65º CIP66

Band Pass FilterGSM900 / GSM1800890 - 960 MHz1710 - 1880 MHz

PRELIMINARY


RevC

Technical Specifications for the Band Pass Filter GSM900 / GSM1800Below are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:Passband:RejectbandInsertion loss:Input return loss:Attenuation in rejection band: Max input power/port: DC BypassImpedance in/out:


EG 602 0031890 - 960 MHz 1920 - 2170 MHz< 1 dB (0.5 typ)> 18 dB> 60 dB

100 WYes50 Ohm

< -110 dBm (153 dBc)

EG 602 00321710 - 1880 MHz 1920 - 2170 MHz< 1 dB (0.5 typ)> 18 dB> 60 dB

100 WYes50 Ohm

< -110 dBm (153 dBc)


195 x 150 x 70 mm7/16 (f) 1.4 kg

195 x 150 x 70 mm7/16 (f) 1.4 kg



without notice.



Band Pass FilterUMTS 1920 - 2170 MHz


RevA

Technical Specifi cations for the Band Pass Filter UMTS2100Below are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband:Stop band

Insertion loss:1920 - 2170 MHz

Input return loss:

Attenuation in rejection band:0 -1900 MHz> 2190 MHz


Impedance in/out:


EG 602 01701920 - 2170 MHz< 1900 MHz> 2190 MHz

< 0.5 dB

> 17.5 dB

> 50 dB> 30 dB

150 W

50 Ohm

< -110 dBm, (153 dBc)


190 x 120 x 50 mm7/16 (f)2.3 kg



without notice.

-35 to + 65º CIP66

Dual Band Pass FilterUMTS2100


RevA

Technical Specifi cations for the Band Pass Filter UMTS2100Below are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband RX:Passband TX:

Stop band

Insertion loss:RX:TX:

Input return loss:

Attenuation in rejection band:1970 - 1980 MHz1980 - 2000 MHz


Impedance in/out:


EG 602 02001950 - 1965 MHz2140 - 2155 MHz

1970 - 2000 MHz

< 1.5 dB < 0.8 dB

> 18 dB

> 40 dB> 50 dB

100 W

50 Ohm

< -110 dBm, (153 dBc)

EG 602 02011935 - 1965 MHz2125 - 2155 MHz

1970 - 2000 MHz

< 1.5 dB < 0.8 dB

> 18 dB

> 40 dB> 50 dB

100 W

50 Ohm

< -110 dBm, (153 dBc)


300 x 72 x 95 mm7/16 (f) - 7/16(m)3.5 kg

300 x 72 x 95 mm7/16 (f) - 7/16(m)3.5 kg



without notice.

-30 to + 65º CIP66

-30 to + 65º CIP66

Phase Adjuster www.egant.se

Frequency range Description Connector Ordering numberPhase Adjuster791-821, 832-862MHz Phase Adjuster LTE800 7/16(f) EG 602 0137890-915, 935-960MHz Phase Adjuster GSM900 7/16(f) EG 100 9032880-915, 925-960MHz Phase Adjuster EGSM 7/16(f) EG 602 01332500-2570, 2620-2690MHz Phase Adjuster LTE2600 7/16(f) EG 602 0138

Phase Adjuster / DuplexerLTE 800


Rev B

Technical Specifications for the Phase Adjuster/DuplexerBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:Passband:Insertion loss: Port 1 - Ant 1: 791 - 821 MHz Port 2 - Ant 2: 791 - 821 MHz Port 2 - Ant 1: 832 - 862 MHz Port 2 - Ant 2: 832 - 862 MHz

Phase difference: Port 1 - Ant 1: 791 - 821 MHz Port 2 - Ant 2: 791 - 821 MHz Port 2 - Ant 1: 832 - 862 MHz Port 2 - Ant 2: 832 - 862 MHz

EG 602 0137 791 - 821, 832 - 862 MHz < 1.5 dB (0.9 dB typ)< 1.5 dB (0.9 dB typ)< 4.8 dB (4.1 dB typ 3 dB coupling)< 4.8 dB (4.1 dB typ 3 dB coupling)

0° 0°0 + 3° (+ 1° typ)0 + 3° (+ 1° typ)

Input return loss:Isolation between UL - DL:Max input power/port:Impedance in/out:


> 18.0 dB> 30 dB2 x 35 W50 Ohm

105 x 240 x 165 mm7/16 (f) 3.7 kg


Egant reserves the right to change this product specification at any time without notice.


Phase Adjuster / DuplexerGSM 900


RevD



Phase difference: Port 1 - Ant 1: 890 - 915 MHz Port 1 - Ant 2: 890 - 915 MHz Port 1 - Ant 1: 935 - 960 MHz Port 1 - Ant 2: 935 - 960 MHz Port 2 - Ant 1: 935 - 960 MHz Port 2 - Ant 2: 935 - 960 MHz


0°0°- 90 + 3° (+ 1° typ)- 90 + 3° (+ 1° typ)0 + 3° (+ 1° typ)0 + 3° (+ 1° typ)



> 18.0 dB> 30 dB2 x 35 W50 Ohm

105 x 240 x 165 mm7/16 (f) 3.7 kg




Phase Adjuster / DuplexerEGSM 900


RevB





0° 0°0 + 3° (+ 1° typ)0 + 3° (+ 1° typ)



> 18.0 dB> 30 dB2 x 35 W50 Ohm

105 x 240 x 165 mm7/16 (f) 3.7 kg




Phase Adjuster / DuplexerLTE 2600


Rev B





0° 0°0 + 3° (+ 1° typ)0 + 3° (+ 1° typ)



> 18.0 dB> 30 dB2 x 35 W50 Ohm

105 x 240 x 165 mm7/16 (f) 3.7 kg




Protection Filter www.egant.se

Frequency range Description Connector Ordering numberProtection Filter876-880MHz, 921-925MHz Reject band 885-915, 930-960 N(f) EG 602 0116885-915MHz, 930-960MHz Reject band 876-880, 921-925 N(f) EG 602 0118876-880MHz, 921-925MHz Reject band 885-915, 930-960 7/16(f) EG 602 0117885-915MHz, 930-960MHz Reject band 876-880, 921-925 7/16(f) EG 602 0119

Protection Filter885-915MHZ + 930-960MHz 876-880MHZ + 921-925MHz

The Protection filters is design to eliminate in-terferance between GSM-R and E-GSM.The filters handles both Uplink and Downlink signals making it very easy to install on an ex-isting system.


RevC

Technical Specifications for Protection FiltersBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:

Passband:

Insertion loss:

Input return loss:

Rejection frequency:

Rejection: Max input power/port:

Impedance in/out:


EG 602 0116GSM-R 876 - 880 MHz + 921 - 925 MHz

< 1,6 dB, typ 0.7dB

> 18.0 dB

885 - 915MHz + 930 - 960MHz> 50 dB

200 W

50 Ohm

< -110 dBm

EG 602 0117GSM-R 876 - 880 MHz + 921 - 925 MHz

< 1,6 dB, typ 0.7dB

> 18.0 dB

885 - 915MHz + 930 - 960MHz> 50 dB

200 W

50 Ohm

< -110 dBm

EG 602 0118E-GSM 885 - 915 MHz + 930 - 960 MHz

< 1,6 dB, typ 0.7dB

> 18.0 dB

876 - 880MHz +921 - 925MHz> 50 dB

200 W

50 Ohm

< -110 dBm

EG 602 0119E-GSM 885 - 915 MHz + 930 - 960 MHz

< 1,6 dB, typ 0.7dB

> 18.0 dB

876 - 880MHz +921 - 925MHz> 50 dB

200 W

50 Ohm

< -110 dBm


180 x 65 x 150mN (f) 1.5 kg

180 x 65 x 150m7/16 (f) 1.5 kg

180 x 65 x 150mN (f) 1.5 kg

180 x 65 x 150m7/16 (f) 1.5 kg


Low Pass Filters www.egant.se

Frequency range Description Connector Ordering numberLow Pass FilterDC-500MHz Reject 790-2700 7/16(f) EG 602 0128DC-500MHz Reject 960-2500 N(m)-N(f) EG 602 0050DC-960MHz Reject 1710-18GHz N(m)-N(f) EG 602 0052

Low Pass FilterDC- 500 MHzReject 790-2700MHz


RevB

Technical Specifications for Low Pass FiltersBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number: Passband:Rejection band:

Insertion loss:

Input return loss376-500MHz:DC-375MHz:

Attenuation/Reject Band Max input power/port:

Impedance in/out:

EG 602 0128 DC - 500 MHz 790 - 2700 MHz

< 0.3dB (0.1dB typ)

> 16.0 dB> 10.0 dB

> 40dB

250 W

50 Ohm

Mechanical SpecificationsDimensions (W x H x D) mm:Connectors:Weight:

375 x 40 x 407/16(f) 1,2 kg





Low Pass FilterDC- 500 MHzDC - 960 MHz


RevD

Technical Specifications for Low Pass FiltersBelow are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number: Passband:Rejection band:

Insertion loss:

Input return loss376-960MHz:>380MHz

Attenuation/Reject Band Max input power/port:

Impedance in/out:


EG 602 0050 DC - 500 MHz 960 - 2500 MHz

< 0.3dB (0.1dB typ)

> 18.0 dB> 10.0 dB

> 70dB

250 W

50 Ohm

< -117 dBm (160 dBc)

EG 602 0052 DC - 960 MHz 1710 MHz - 18 GHz

< 0.3dB (0.1dB typ)

> 18.0 dB> 11.0 dB

> 70dB

250 W

50 Ohm

< -117 dBm (160 dBc)

EG 602 0070 DC - 960 MHz 1710 MHz - 18 GHz

< 0.4dB (0.15dB typ)

> 13.0 dB> 10.0 dB

> 70dB

250 W

75 Ohm

< -117 dBm (160 dBc)

Mechanical SpecificationsDimensions (W x H x D) mm:Connectors:Weight:

127 x 56 x 30 N(m) - N(f) 0.7 kg

127 x 56 x 30N(m) - N(f) 0.6 kg

127 x 56 x 30N(m) - N(f) 0.6 kg







4x4 Combiners www.egant.se

Frequency range Description Connector Ordering number4x4 Combiners376-960MHz 4-Way Combiner N(f) EG 500 8008376-960MHz 4-Way Combiner 7/16(f) EG 603 0014376-2200MHz 4-Way Combiner 7/16(f) EG 603 0008700-2700MHz 4-Way Combiner N(f) EG 603 0080700-2700MHz 4-Way Combiner 7/16(f) EG 603 0081800-960MHz 4-Way Combiner N(f) EG 500 80011710-2200MHz 4-Way Combiner N(f) EG 500 80021710-2700MHz 4-Way Combiner N(f) EG 603 00781710-2700MHz 4-Way Combiner 7/16(f) EG 603 0079

MCM 4-Way Combiner BroadbandTETRA, CDMA2000, GSM900376 - 960 MHz

Combines up to 4 RBSs into the same antenna system

The 4-way combiner enables you to connect 4 Base Stations. The combiner combines the signal and equally splits it between the an-tenna ports.

This is a highly important function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.

Innovative design

The 4-way combiner incorporates a broad band and low loss product design. The 4-way combiner is designed for low insertion loss and intermodulation.

There is no need for terminations or attenu-ators, which results in very low insertion loss and outstanding intermodulation perfor-mance.

The benefits from installing the 4-way combiner instead of hybrid combiners and splitters are:

· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement

RBS 4RBS 4RBS 3RBS 3


ANT2ANT2

ANT1ANT1 ANT3ANT3

ANT4ANT4


RevD

Technical Specifications for 4-Way Combiner Broadband (MCM)Below are some typical data. For more detailed information, please contact us.

Electrical SpecificationsProduct number:Passband:

Isolation between ports:Input return loss:Coupling: Max input power/port:

3rd order intermodulation:IM3, 2 x 43 dBm:Impedance in/out:

EG 500 8008376 - 500 MHz, 880 - 960 MHz

> 25 dB> 18.0 dB6.4 + 0.7 dB100 W

<-110 dBm (153 dBc)50 Ohm

EG 603 0014376 - 500 MHz, 880 - 960 MHz

> 25 dB> 18.0 dB6.4 + 0.7 dB100 W

<-110 dBm (153 dBc)50 Ohm

Mechanical SpecificationsDimensions (W x H x D):Connectors:

310 x 130 x 130 mmN (f)

380 x 150 x 130 mm7/16 (f)





4-Way Combiner Broadband376 - 2200 MHz

Combines up to 4 RBSs into the shared antenna system

The 4-way combiner enables the connection of 4 Radio Base Stations. It combines the signal and equally splits it between the antenna ports. This is a highly important function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.

Innovative design

The 4-way combiner incorporates a broad band and low loss product design. It is spe-cifically designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low insertion loss and outstanding inter-modulation performance.

The benefits from installing the 4-way combiner instead of hybrid combiners and splitters are:




ANT2ANT2

ANT1ANT1 ANT3ANT3

ANT4ANT4


RevE

Technical Specifications for 4-Way Combiner Broadband (MCM)Below are some typical data. For more detailed information, please contact us.


Isolation between ports:

Input return loss:

Coupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm:

Impedance in/out:

EG 603 0008376 - 2200 MHz

> 25 dB (30 dB typ)

> 17.0 dB

6.4 + 1.0 dB

100 W

<-110 dBm (153 dBc) 50 Ohm

EG 603 0069376 - 2200 MHz

> 25 dB (30 dB typ)

> 17.0 dB

6.4 + 1.0 dB

100 W

<-110 dBm (153 dBc) 50 Ohm

Mechanical Specifications Dimensions (W x H x D):Connectors:

410 x 130 x 130 mm7/16 (f)

410 x 130 x 130 mmN(f)





Multicasting Matrix MCM 4 x 4700 - 2700 MHz / LTE800,GSM, TDMA, UMTS, LTE2600


The advanced MCM enables you to connect 4 Radio Base Stations. The MCM combines the signals and equally splits them between the antenna ports. This is a highly important function when designing shared antenna sys-tems wishing to connect multiple RBSs to the shared antennas.

Sleek design

The MCM incorporates a broad band and low loss product design. The MCM is specifically designed for low insertion loss and low inter-modulation. There is no need for terminations or attenuators, which results in very low in-sertion loss and outstanding intermodulation perfomance.

The benefits from installing the MCM instead of hybrid combiners and splitters are: · Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement



Floor 1

Floor 2

Floor 3

Floor 4


RevC

Technical Specifications for the Multicasting Matrix (MCM)Below are some typical data. For more detailed information, please contact us.



Input return loss:

Coupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 603 0080700 - 2700 MHz

> 25 dB, typ >33dB

> 21 dB, typ >25dB

6.4 + 0.7 dB

150 W

< - 110 dBm, 153 dBc 50 Ohm

EG 603 0081700 - 2700 MHz

> 25 dB, typ >33dB

> 21 dB, typ >25dB 6.4 + 0.7 dB

150 W

< - 110 dBm, 153 dBc 50 Ohm


274 x 35 x 155 mmN (f)2,25 Kg

274 x 35 x 155 mm7/16 (f)2.25 Kg





Multicasting Matrix MCM 4 x 4800 - 960 MHz / GSM, NMT, AMPS1710 - 2200 MHz / GSM, TDMA, UMTS



Sleek design





Floor 1

Floor 2

Floor 3

Floor 4


RevE



Isolation between ports:Input return loss:Insertion loss:Coupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 500 8001800 - 960 MHz

> 25 dB > 22.0 dB< 0.3 dB6.2 + 0.5 dB100 W

< - 105 dBm, 148 dBc 50 Ohm

EG 500 80021710 - 2200 MHz

> 25 dB > 22.0 dB< 0.3 dB6.2 + 0.5 dB100 W

< - 105 dBm, 148 dBc 50 Ohm


274 x 35 x 155 mmN (f)2.25 Kg

274 x 35 x 155 mmN (f)2.25 Kg





ANT ANT ANT ANT

IN / OUT IN / OUT IN / OUT IN / OUT

Multicasting Matrix MCM 4 x 41710 - 2700 MHz / GSM, TDMA, UMTS, LTE



Sleek design





Floor 1

Floor 2

Floor 3

Floor 4


RevB



Isolation between ports:Input return loss:Insertion loss:Coupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 603 00781710 - 2700 MHz

> 25 dB, > 22.0 dB< 0.3 dB6.2 + 0.5 dB100 W

< - 105 dBm, 148 dBc 50 Ohm

EG 603 00791710 - 2700 MHz

> 25 dB > 22.0 dB< 0.3 dB6.2 + 0.5 dB100 W

< - 105 dBm, 148 dBc 50 Ohm


220 x 34 x 115 mmN (f)

220 x 34 x 115 mm7/16 (f)





3x3 Combiners www.egant.se

Frequency range Description Connector Ordering number3x3 Combiners376-960MHz 3x3 Combiner N(f) EG 603 0091376-960MHz 3x3 Combiner 7/16(f) EG 603 0092700-2700MHz 3x3 Combiner N(f) EG 603 0040700-2700MHz 3x3 Combiner 7/16(f) EG 603 0039

3x3 Combiner 4.8dB376 - 960 MHz


The 3x3 combiner enables the connection of 3 Radio Base Stations to the combiner. The com-biner combines the signal and equally splits the signals between the antenna ports.


Innovative design

The 3x3 combiner is a broad band and low loss product design. It is intentionally de-signed for low insertion loss and lowintermodulation.

The benefits of using our 3x3 combiner are:· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement

Egant ABBox 945SE-114 79 Stockholm SwedenPhone: +46 (0)8 62 00 650E-mail: [email protected]

Technical Specifications for the 3x3 CombinerBelow are some typical data. For more detailed information, please contact us.


Coupling: Input return loss: Isolation between ports: Intermodulation 2 x 43 dBm:

Max input power/port: Max peak power:

Impedance in/out:

EG 603 0091376 - 960 MHz

5.0 +/- 1.0 dB > 20.0 dB> 25 dB (30 dB typ.)< 107 dBm (150 dBc) 60 W 3 kW

50 Ohm

EG 603 0092376 - 960 MHz

5.0 +/- 1.0 dB > 20.0 dB> 25 dB (30 dB typ.)< 107 dBm (150 dBc) 60 W 3 kW

50 Ohm


175 x 38 x 195 mmN (f)2.0 kg

175 x 38 x 195 mm7/16 (f)2.0 kg





RevC

3x3 Combiner 4.8dB698 - 2700 MHz


The 3x3 combiner enables the connection of 3 Radio Base Stations to the combiner. The com-biner combines the signal and equally splits the signals between the antenna ports.


Innovative design

The 3x3 combiner is a broad band and low loss product design. It is intentionally de-signed for low insertion loss and lowintermodulation.

The benefi ts of using our 3x3 combiner are:· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement

3dB Combiners www.egant.se

Frequency range Description Connector Ordering number3dB Combiners68-79MHz 3 dB Combiner N(f) EG 603 0001150-2700MHz 3 dB Combiner N(f) EG 603 0074150-2700MHz 3 dB Combiner 7/16(f) EG 603 0076376-960MHz 3 dB Combiner N(f) EG 500 8017376-960MHz 3 dB Combiner 7/16(f) EG 500 8018376-2200MHz 3 dB Combiner N(f) EG 603 0030376-2200MHz 3 dB Combiner 7/16(f) EG 603 0031376-2700MHz 3 dB Combiner N(f) EG 603 0072376-2700MHz 3 dB Combiner 7/16(f) EG 603 0073700-2700MHz 3 dB Combiner N(f) EG 500 8011700-2700MHz 3 dB Combiner 7/16(f) EG 500 8010


Technical Specifi cations for the 3x3 CombinerBelow are some typical data. For more detailed information, please contact us.

Electrical Specifi cationsProduct number:Passband:

Coupling: (698 - 2200 MHz)Coupling: (2200 - 2700 MHz)

Input return loss:Isolation between ports:Intermodulation 2 x 43 dBm:

Max input power/port:Max peak power:

Impedance in/out:

EG 603 0039698 - 2700 MHz

5.0 +/- 0.8 dB5.3 +/- 1.3 dB

> 20.0 dB> 25 dB (30 dB typ.)< 107 dBm (150 dBc)

150 W3 kW

50 Ohm

EG 603 0040698 - 2700 MHz

5.0 +/- 0.8 dB5.3 +/- 1.3 dB

> 20.0 dB> 23 dB (28 dB typ.)< 107 dBm (150 dBc)

150 W3 kW

50 Ohm


204 x 32 x 140 mm7/16 (f)1.6 kg

204 x 25 x 140 mmN (f)1.4 kg


Egant reserves the right to change this product specifi cation at any time without notice.



RevE

3 dB Combiner68 - 79 MHz

Combines up to 2 repeaters or RBSs into the same antenna system

The 3 dB combiner enables the connection of 2 repeaters or radio base stations. The com-biner combines the signal and equally splits the signals between the antenna ports. This is a highly important function when designing shared antenna systems wishing to connect multiple repeaters or RBSs to the shared antennas.

The benefits from installing the 3 dB combiner instead of power splitters are:


Innovative design

The 3 dB combiner incorporates a broad band and low loss design. It is specifically designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low inser-tion loss and outstanding intermodulation performance.

EG 699 0006

Bracket for EGANT Cellular Components combiner.


ANT1 ANT2ANT1 ANT2


RevC

Technical Specifications for the 3 dB CombinerBelow are some typical data. For more detailed information, please contact us.



Input return loss:

Coupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 603 000168 - 79 MHz

> 30 dB

> 20.0 dB

3.1 + 0.2 dB

120 W

< - 97 dBm, 140 dBc 50 Ohm

Mechanical Specifications Dimensions (W x H x D):Connectors:

190 x 25 x 82 mmN (f)



Installation bracket:Material:

EG 699 0006Aluminum Zinc


In 1 In 2

Out 1 + 2 Out 1 + 2

3 dB Combiner, Broad Band 150 - 2700 MHz VHF, TETRA, GSM900, GSM1800, UMTS, LTE



Innovative design

The 3dB combiner incorporates a broad band and low loss design. It is specifically designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low inser-tion loss and outstanding intermodulation performance.




ANT1 ANT2ANT1 ANT2


Rev C



Isolation between ports:150 - 2700 MHz:

Input return loss:150 - 2500 MHz>2500 - 2700 MHzCoupling:Input 1: 150 - 160 MHz - Ant 1Input 1: 150 - 160 MHz - Ant 2Input 2: 150 - 160 MHz - Ant 1Input 2: 150 - 160 MHz - Ant 2

376 - 2500 MHz>2500 - 2700 MHz Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 603 0074150 - 2700 MHz

> 24 dB (typ 30 dB)

> 18.0 dB> 16.0 dB, typ 18 dB

1.0 +/- 0.3 dB7.1 +/- 0.3 dB7.1 +/- 0.3 dB1.0 +/- 0.3 dB

3.1 +/- 0.3 dB3.3 +/- 0.4 dB

200 W

< - 150dBc 50 Ohm

EG 603 0076150 - 2700 MHz

> 24 dB (typ 30 dB)

> 18.0 dB> 16.0 dB, typ 18 dB

1.0 +/- 0.3 dB7.1 +/- 0.3 dB7.1 +/- 0.3 dB1.0 +/- 0.3 dB

3.1 +/- 0.3 dB3.3 +/- 0.4 dB

200 W

< - 150dBc 50 Ohm


215 x 26 x 115 mmN (f)1 Kg

215 x 26 x 115 mm7/16 (f)1 Kg





3 dB Combiner, Broad Band 376 - 960 MHz TETRA, GSM900


The 3 dB combiner enables the connection of 2 repeaters or radio base stations. The com-biner combines the signal and equally splits the signals between the antenna ports. This is a highly desirable function when design-ing shared antenna systems wishing to con-nect multiple repeaters or RBSs to the shared antennas.

Innovative design

The 3 dB combiner is designed for low inser-tion loss and low intermodulation.There is no need for terminations or attenua-tors, which results in very low insertion loss and outstanding intermodulation perfomance.

The benefits from installing the 3 dB combiner instead of hybrid combiners and splitters are: · Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement


ANT1 ANT2ANT1 ANT2

EG 699 0006Bracket for EGANT Cellular Componentscombiner.


RevE



Isolation between ports:376 - 500MHz876 - 960MHzInput return loss:Coupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 500 8017376 - 500 MHz, 876 - 960 MHz

> 30 dB (typ 33 dB)> 26 dB (typ 30 dB)> 20.0 dB3.1 +/- 0.4 dB120 W < - 110 dBm (153dBc) 50 Ohm

EG 500 8018376 - 500 MHz, 876 - 960 MHz

> 30 dB (typ 33 dB)> 26 dB (typ 30 dB)> 20.0 dB3.1 +/- 0.4 dB120 W < - 110 dBm (153dBc) 50 Ohm


190 x 25 x 82 mmN (f)

190 x 42 x 82 mm7/16 (f)





In 1

In 2

Out 1 + 2

Out 1 + 2

3 dB Combiner, Broad Band 376 - 2200 MHz TETRA, GSM900, GSM1800, UMTS



Innovative design





ANT1 ANT2ANT1 ANT2


Rev C



Isolation between ports:376 - 1500 MHz:1500 - 2200 MHz:

Input return loss:376 - 1500 MHz1500 - 2200 MHzCoupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 603 0030376 - 2200 MHz

> 25 dB (typ 30 dB)> 20 dB (typ 25 dB)

> 20.0 dB> 18.0 dB3.1 + 0.2 dB200 W

< - 97 dBm 50 Ohm

EG 603 0031376 - 2200 MHz

> 25 dB (typ 30 dB)> 20 dB (typ 25 dB)

> 20.0 dB> 18.0 dB3.1 + 0.2 dB200 W

< - 97 dBm 50 Ohm


215 x 26 x 115 mmN (f)

215 x 26 x 115 mm7/16 (f)





3 dB Combiner, Broad Band 376 - 2700 MHz TETRA, GSM900, GSM1800, UMTSLTE



Innovative design





ANT1 ANT2ANT1 ANT2


Rev B



Isolation between ports:376 - 1500 MHz:1500 - 2700 MHz:

Input return loss:376 - 1500 MHz1500 - 2700 MHzCoupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 603 0072376 - 2700 MHz

> 25 dB (typ 30 dB)> 20 dB (typ 25 dB)

> 20.0 dB> 18.0 dB3.1 +/- 0.3 dB200 W

< - 97 dBm 50 Ohm

EG 603 0073376 - 2700 MHz

> 25 dB (typ 30 dB)> 20 dB (typ 25 dB)

> 20.0 dB> 18.0 dB3.1 +/- 0.3 dB200 W

< - 97 dBm 50 Ohm


215 x 26 x 115 mmN (f)

215 x 26 x 115 mm7/16 (f)





3 dB Combiner, Broad Band 700 - 2700 MHz GSM, TDMA, UMTS, W-LAN, LTE



Innovative design

The 3 dB combiner incorporates a broad band and low loss design. It is specifically designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low inser-tion loss and outstanding intermodulation performance.




ANT1 ANT2ANT1 ANT2


ANT1 ANT2ANT1 ANT2


RevE



Isolation between ports:Input return loss:Coupling: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 500 8010700 - 2700 MHz

> 30 dB > 22.0 dB3.1 + 0.3 dB240 W <-110 dBm (153 dBc)50 Ohm

EG 500 8011700 - 2700 MHz

> 30 dB > 22.0 dB3.1 + 0.3 dB240 W <-110 dBm (153 dBc)50 Ohm


135 x 45 x 80 mm7/16 (f)

135 x 45 x 80 mmN (f)





In 1 In 2

Out 1 + 2 Out 1 + 2

2-Way Combiners www.egant.se

Frequency range Description Connector Ordering number2-Way Combiner88-2700MHz 2-Way Combiner 7/16(f) EG 603 0088376-500MHz 2-Way Combiner 4.7dB 7/16(f) EG 100 9104376-500MHz 2-Way Combiner 6dB 7/16(f) EG 100 9106376-500MHz 2-Way Combiner 10dB 7/16(f) EG 100 9110376-500MHz 2-Way Combiner 4.7dB N(f) EG 100 9304376-500MHz 2-Way Combiner 6dB N(f) EG 100 9306376-500MHz 2-Way Combiner 7dB N(f) EG 100 9307376-500MHz 2-Way Combiner 10dB N(f) EG 100 9310800-2170MHz 2-Way Combiner 4.7dB 7/16(f) EG 100 9004800-2170MHz 2-Way Combiner 6dB 7/16(f) EG 100 9006800-2170MHz 2-Way Combiner 10dB 7/16(f) EG 100 9010800-2170MHz 2-Way Combiner 4.7dB N(f) EG 100 9204800-2170MHz 2-Way Combiner 6dB N(f) EG 100 9206800-2170MHz 2-Way Combiner 7dB N(f) EG 100 9207800-2170MHz 2-Way Combiner 10dB N(f) EG 100 9210800-2170MHz 2-Way Combiner 4.7dB 7/16(m),7/16(f), N(f) EG 603 0011800-2170MHz 2-Way Combiner 6dB 7/16(m),7/16(f), N(f) EG 603 0012

2-Way Combiner88 - 2700 MHz380 - 400 MHz / 1575 - 1576MHz


The 2-Way combiner enables the connection of 2 Radio Base Stations to the combiner. The combiner combines the signal and equally splits the signals between the antenna ports.


Innovative design

The 2-Way combiner is a broad band and low loss product design. It is intentionally de-signed for low insertion loss and lowintermodulation.

The benefits of using our 2-Waycombiner are:· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement


Technical Specifications for the 2-Way CombinerBelow are some typical data. For more detailed information, please contact us.


Coupling: Input return loss: Isolation between ports:

Max input power/port: Max peak power:

Impedance in/out:

EG 603 008888 - 2700 MHz

3.0 +/- 0.2 dB > 8.0 dB

3 dB +/- 1.0 dB 200 W 3 kW

50 Ohm

EG 603 0089380 - 400 / 1575 - 1576 MHz

3.0 +/- 0.2 dB > 12.0 dB, typ 16dB

3 dB +/- 1.0 dB 200 W 3 kW

50 Ohm


100 x 40 x 70 mm7/16 (f)0,8 kg

100 x 40 x 70 mm7/16 (f)0,8 kg





RevD

2-Way Combiner 376 - 500 MHz800 - 2170 MHzTETRA, GSM900, GSM1800, DCS, UMTS

Combining with optimization

Do you have radio base stations orrepeaters in separate locations? Egant has the solution. Our 2-way combiner enables you to optimize your system by compensating for the added cable loss in addition to combining the signals into one point with equal power, add-ing control over signal strength to the antenna.

Innovative design

This 2-way combiner incorporates a broad band and low loss product design. It is de-signed for low insertion loss and intermodula-tion.

The benefits from installing the 2-way combiner are:

· Higher antenna isolation· Lower insertion loss· Fewer system components· Higher system quality· Cost-effective design improvement


ANTANT

Cable lossCable loss 100%

4.7 dB3 dB, 50%


RevD

Technical Specifications for the 2-Way Combiner Below are some typical data. For more detailed information, please contact us.


Isolation between ports:Input return loss:Coupling in 1 - out:Coupling in 2 - out: Max input power/port: 3rd order intermodulation:IM3, 2 x 43 dBm: Impedance in/out:

EG 100 9004800 - 2170 MHz

> 30 dB> 20.0 dB1.8 + 0.3 dB4.7 + 0.3 dB 70 W <-110 dBm (153 dBc)

50 Ohm

EG 100 9006800 - 2170 MHz


50 Ohm

EG 100 9010800 - 2170 MHz


50 Ohm


140 x 80 x 40 mm7/16 (f)

140 x 80 x 40 mm7/16 (f)

140 x 80 x 40 mm7/16 (f)







EG 100 9104376 - 500 MHz

> 30 dB> 20.0 dB1.8 + 0.15 dB4.7 + 0.15 dB

70 W

<-110 dBm (153 dBc) 50 Ohm

EG 100 9106376 - 500 MHz

> 30 dB> 20.0 dB1.2 + 0.15 dB6.0 + 0.15 dB

70 W

<-110 dBm (153 dBc) 50 Ohm

EG 100 9110376 - 500 MHz

> 30 dB> 20.0 dB1.0 + 0.15 dB10.0 + 0.15 dB

70 W

<-110 dBm (153 dBc) 50 Ohm


140 x 80 x 40 mm7/16 (f)

140 x 80 x 40 mm7/16 (f)

140 x 80 x 40 mm7/16 (f)





Installation support Installation bracket: EG 699 0007 (Order separately)


2-Way Combiner 376 - 500 MHz800 - 2170 MHzTETRA, GSM900, GSM1800, DCS, UMTS

Combining with optimization

Do you have radio base stations orrepeaters in separate locations? Egant has the solution. Our 2-way combiner enables you to optimize your system by compensating for the added cable loss in addition to combining the signals into one point with equal power, add-ing control over signal strength to the antenna.

Innovative design

This 2-way combiner incorporates a broad band and low loss product design. It is de-signed for low insertion loss and intermodula-tion.

The benefits from installing the 2-way combiner are:

· Higher antenna isolation· Lower insertion loss· Fewer system components· Higher system quality· Cost-effective design improvement


ANTANT

Cable lossCable loss 100%

4.7 dB3dB, 50%


RevE

Technical Specifications for the 2-Way Combiner Below are some typical data. For more detailed information, please contact us.



EG 100 9204800 - 2170 MHz

> 30 dB> 20.0 dB1.8 + 0.3 dB4.7 + 0.3 dB 500 W <-110 dBm (153dBc)50 Ohm

EG 100 9206800 - 2170 MHz


EG 100 9207800 - 2170 MHz

> 30 dB> 20.0 dB1.1 + 0.15 dB7.0 + 0.15 dB

500 W

<-110 dBm (153dBc)50 Ohm

EG 100 9210800 - 2170 MHz



140 x 80 x 40 mmN (f)

140 x 80 x 40 mmN (f)

140 x 80 x 40 mmN (f)

140 x 80 x 40 mmN (f)








EG 100 9304376 - 500 MHz

> 30 dB> 20.0 dB1.8 + 0.2 dB4.7 + 0.4 dB

500 W

<-110 dBm (153dBc)50 Ohm

EG 100 9306376 - 500 MHz

> 30 dB> 20.0 dB1.2 + 0.2 dB6.0 + 0.4 dB

500 W

<-110 dBm (153dBc)50 Ohm

EG 100 9307376 - 500 MHz

> 30 dB> 20.0 dB1.1 + 0.2 dB7.0 + 0.4 dB

500 W

<-110 dBm (153dBc)50 Ohm

EG 100 9310376 - 500 MHz

> 30 dB> 20.0 dB1.0 + 0.2 dB10.0 + 0.4 dB

500 W

<-110 dBm (153dBc)50 Ohm


140 x 80 x 40 mmN (f)

140 x 80 x 40 mmN (f)

140 x 80 x 40 mmN (f)

140 x 80 x 40 mmN (f)






Installation support Installation bracket: EG 699 0007



(Order separately)

Documents

High performance site components Combiners_Filters.pdfTriple Band Combiner Frequency range Description Connector Ordering number Triple Band Combiners DC-2170, 2400-2500, 5000-6000MHz