Upload
duongnhi
View
222
Download
0
Embed Size (px)
Citation preview
Top Quality - Best Results
Spray Tips, Systems and Accessories
ThermoplasticHoses, High andLow pressure
PricelessProduct Book
Airless and Air Assisted Airless
High performance products
®
®
Contact us
by email: [email protected] phone: 01202 478334by fax: 01202 488110
Find us on the web at www.exitflex.co.ukCheck-out Tri-A.com website
Dealer Nett Price List - Index
AIR FED BREATHING APPARATUS 42 - 43
EXTENSION LANCES - CONVENTIONAL, 44 - 45
AIR SPRAY GUNS
GENERAL CONSUMABLES 46 - 47
TWIN TIPS 48 - 49
AIRLESS SPRAY TIPS, ACCESSORIES AND 50 - 57
TIP CHART
DRAIN CLEANING NOZZLES 50
AIR ASSISTED AIRLESS SPRAY TIPS/SEALS & 52
AIR CAPS
REVERSIBLE AIRLESS TIP SYSTEMS 53 - 57
AIRLESS EXTENSION LANCES, POLEGUNS 58 - 59
AND EXTRUSION GUNS
AIRLESS SPRAY GUNS - MANUAL & AUTOMATIC 60 - 63
AIR ASSISTED AIRLESS SPRAY GUNS 64 - 66
TRI-A REVERSIBLE AAA SYSTEM 67
SUCTION SYSTEMS, ASSEMBLIES & WANDS 68 - 72
COLOUR CHANGE SYSTEM 73 - 76
REFERENCE CHARTS 77 - 79
LOW PRESSURE AIR & FLUID HOSE - BULK 4
LOW PRESSURE TUBING 5
AND CONNECTIONS
LOW PRESSURE AIR & FLUID HOSE ASSEMBLIES 6 - 7
AND TURBINE HOSES
HOSE SLEEVING 7 + 17
LOW PRESSURE HOSE CONNECTIONS 8
AIR CONTROLS 9
TEXTILE BRADED HYDRAULIC HOSE R7, R8 10 - 11
HIGH PRESSURE HOSES - BULK 12 - 15
HIGH PRESSURE. HOSE ASSEMBLIES 16 - 17
HIGH PRESSURE REUSEABLE HOSE FITTINGS 18
HIGH PRESSURE SWIVELS ‘Z’ SWIVELS, UNIONS 19
AND FERRULES
HIGH PRESSURE HOSE SWAGE INSERTS 20 - 21
COUPLINGS & ADAPTORS 22 - 24
FILTER HOUSINGS & SCREENS, BOOTH FILTERS 25 - 29
FLUID CONTROL 30 - 33
ACCESSORIES AND Y BLOCKS 34 - 35
AGITATORS 36
MIX TANKS 37
PRESSURE FEED EQUIPMENT 38 - 39
PRE-TREATMENT NOZZLES 40 - 41
Distibuted by
Low Pressure Hoses in Bulk
NEW
NEW
This section covers Air, Powder and Fluid hosesprincipally for conventional spray,electrostatic powder, air tools, or low pressure transfer
IMPORTANT NOTE:Hoses listed here are non conductive unless otherwise stated.
TYPE APPLICATION ID OD MWP COIL SIZE BUILDREF mm mm Bar m
AB 1.6/100 Breathing air hose blue 10 16 18 100 Reinf PVC
AL 1.4/30 Air hose red 6.3 13 18 30 Reinf PVCAL 1.4/100 Air hose red 6.3 13 18 100 Reinf PVCAL 1.5/30 Air hose red 8 14 18 30 Reinf PVCAL 1.5/100 Air hose red 8 14 18 100 Reinf PVCAC 1.5 Air hose silver conductive 8 14 20 30 Reinf PU
BR 1.5/100 Black anti-static 8 16 20 100 Rubber
RA 1.5/100 Air hose red 8 14 20 100 R/R.ALLOY
RPUA 1.4/30 Light air hose red 6.3 11 20 30 Reinf PUARPUA 1.5/30 Light air hose red 8 12 20 30 Reinf PUARPUA 1.5/100 Light air hose red 8 12 20 100 Reinf PUA
LF 1.4 Fluid hose clear 6.3 13 20 per metre R/PU + FEPLF 1.6 Fluid hose clear 9.6 16 15 * per metre R/PU + FEP
LM 1.4 Fluid hose clear 6.3 11 20 per metre R/PU + PA11LM 1.6 Fluid hose clear 9.6 14 15 * per metre R/PU + PA11
LMC 1.4 Fluid hose conductive 6.3 11 20 * per metre R/TR.PALMC 1.6 Fluid hose conductive 9.6 14 15 * per metre R/TR.PA
LPC 1.4 Fluid hose (BK) cond 6.3 12 20 * per metre R/PU + PALPC 1.6 Fluid hose (BK) cond 9.6 15 15 * per metre R/PU + PA
LPV 1.4 Fluid hose black 6.3 13 20 per metre R/PU + PALPV 1.6 Fluid hose black 9.6 16 20 per metre R/PU + PALPV 1.8 Fluid hose black 13 19 20 per metre R/PU + PA
LX 1.3 Fluid hose clear - very flexible 4 10 35 per metre R/PU + PA12
MA 1.4 Fluid hose, BK,RD,TR 6.3 11 10 per metre Coex PU/PA
LP 1.8 Suction/Pressure hose (Bk) 13 25 15 per metre R/Pu + PASR 1.12 Suction/Pressure hose (Graco) 19 28 34 per metre Rubber/nylonSR 1.16 Suction/Pressure hose (Graco) 25 38 34 per metre Rubber/nylon
VOW1.4.5 Twinned Air & Fluid Hose LPV1.4 + MO1.5 per metre R/PU + PA plus CoexPressure fed paint spray PU/PE
* Asterisked products are non stock, special order lines. Minimum quantity may apply.
Low Pressure Tubing and Connections
NylonTubing30 metre coils. Stock colour natural. Black, blue, red, green available to special order.Larger coils to special order. Metric sizes. Imperial sizes also available, please enquire.NB: Hoses listed on this page are all non-conductive
TYPE OD ID MWP 30m TYPE OD ID MWP 30mREF mm mm PSI COIL REF mm mm PSI COILENF 4/25 4 2.5 377 ENF 5/3 5 3 348ENF 5/33 5 3.3 225 ENF 6/4 6 4 225ENF 6/45 6 4.5 275 ENF 8/55 8 5.5 310ENF 8/6 8 6 250 ENF 10/7 10 7 310ENF 10/8 10 8 250 ENF 12/8.5 12 8.5 304ENF 12/10 12 10 200 ENF 15/12 15 12 200ENF 16/12 16 12 260 ENF 18/14 18 14 225ENF 22/17 22 17 225 ENF 28/22 28 22 220
PTFE TubingTYPE OD ID 25m TYPE OD ID 25m REF m mm COIL REF mm mm COILPTFE 4/25 4 2.5 - PTFE 10/8 10 8 -PTFE 6/4 6 4 - PTFE 12/10 12 10 -PTFE 8/5 8 5 -PTFE 8/6 8 6 - NB. Other sizes by enquiry.
Polyethylene Tubing30 metre coils. Stock colour natural
TYPE OD ID MWP 30m TYPE OD ID MWP 30mREF mm mm PSI COIL REF mm mm PSI COIL
EPF 6/4 6 4 180 EPF 8/6 8 6 150EPF 10/8 10 8 120
76 Series Tubing Connections Stainless steel wetted section-ideal for water based materials
TYPE REF DESCRIPTION76-032/39 1/4 BSP(F) for 4x6mm tubing76-069/39 3/8 BSP(F) for 4x6mm tubing76-031/39 1/4 NPSM(F) for 4x6mm tubing76-068/39 3/8 NPSM(F) for 4x6mm tubing
76-142/39 1/4 BSP(F) for 6x8mm tubing76-179/39 3/8 BSP(F) for 6x8mm tubing76-141/39 1/4 NPSMF) for 6x8mm tubing76-178/39 3/8 NPSM(F) for 6x8mm tubing
76-252/39 1/4 BSP(F) for 8x10mm tubing76-289/39 3/8 BSP(F) for 8x10mm tubing76-251/39 1/4 NPSM(F) for 8x10mm tubing76-288/39 3/8 NPSM(F) for 8x10mm tubing76-289/39 3/8 BSP(F) for 8x10mm tubing
These connections feature a ‘loose’ nut and 60 degree cone seat.
Connectors are available in 3/8 and 1/4 BSP and NPSM forms.
The wetted section is stainless steel 304 and the ferrule and nut are nickel plated brass, supplied with a spring guardas standard.
Low Pressure Hose Assemblies
Air Hose AssembliesAir hose assemblies with crimped fittings
NB: Air Hose Assemblies in this listing are non conductive unless otherwise statedTYPE REF ID MATERIALTraditional Top Quality PVC HoseAL 1.4 1/4 PVC red Standard lengths 5m 7.5m 10m 15m - others to orderAL 1.5 5/16 PVC red
Breathing Air Hose PVCAB 1.6 3/8 PVC blue
Lightweight Ultra-Airflex PU HoseRPUA 1.4 1/4 PU alloy redRPUA 1.5 5/16 PU alloy red
Superflexible Rubber Style HoseRA 1.5 5/16 Rubber alloy redConductive HoseAC 1.5 5/16 Conductive air hose
Silver
1. Air hose assemblies can be supplied with QD connection.(including gun plug)
2. Re-usable connections could be fitted instead of crimped onhose to all types on the listing.
Low Pressure Fluid Hose AssembliesFluid hose assemblies with crimped fittingsNB: Fluid Hose assemblies in this listing are non-conductive unless otherwise statedTYPE REF ID MATERIALConductive Fluid HoseLPC 1.4 1/4 PU, Nylon lined Standard lengths 5m 7.5m 10m 15m - others to orderLPC 1.6 3/8 PU, Nylon linedLMC 1.6 3/8 PU, Nylon lined
Traditional Fluid HoseLPV 1.4 1/4 PU, Nylon linedLPV 1.6 3/8 PU, Nylon lined
PTFE Lined Hose (FEP 140)LF 1.4 1/4 PU, PTFE linedLF 1.6 3/8 PU, PTFE lined
Lightweight Fluid HoseLM 1.4 1/4 PU, Nylon linedLM 1.6 3/8 PU, Nylon lined
NOTE LPC and LMC are conductive hoses. (To special order only)
1. Re-usable couplings can be fitted instead of crimped on hose to all types on the listing.NB: Choose carefully, conductive or non-conductive
Low pressure Twin Hose Assemblies
HVLP Turbine Hoses & AccessoriesTYPE REF DESCRIPTIONHVLP-8-NPC 8 metre spiral wound hose with swaged connections.
3/4 BSP(F) and QD connection for gun. Ideal forapplications where excess heat is not a problem
HVLP-9-CNPC 9 metre combination hose comprising 4 metre lightspiral wound hose, 5 metre heavy reinforced hose,jointed and complete with 3/4 BSP(F) and QD gun connection
HC-02 17 x 17mm nylon hose couplerHVLP 1/E 3/4” screw ring BSP for 3/4” hose tail. Nickel platedHVLP 1/E/M20 M20 screw ring for 3/4” hose tailHVLP 3/E 18mm diameter hose tail, brassHVLP 5/E QD coupling tail. 18mm brassHVLP 6/E QD coupling. Nickel platedHVLP 8/E Spiral PVC hose smooth bore black (per metre)HVLP 9/E Heavy delivery hose smooth bore black (per metre)HVLP 10/E Hose joiner QD tail x 3/4” male thread.
Twin Fluid & Air: VOW 1.4.5LPV 1.4 and MO 1.5 hose assembly c/w 3/8 BSP(F) on 1/4” ID fluid hose, 1/4 BSP(F) on 5/16” ID air hose (76 series stainless steel wetted section connections)
TYPE REF LENGTHVOW1.4.5:2.2:B 2.2 metresVOW1.4.5:5:B 5 metresVOW1.4.5:7.5:B 7.5 metresVOW1.4.5:10:B 10 metresVOW1.4.5:15:B 15 metresVOW1.4.5
Hose SleevingAvailable as follows:-
PVCT 2/400 PVC sleeve 2" Approx 200m roll 400 gaugePVCT 3/400 PVC sleeve 3" Approx 200m roll 400 gaugeGW30 BK Polyester braid 25/30mm per metreGW40 GR Polyester braid 40/60mm per metre
Low Pressure Hose Connections
Low Pressure Reusable Hose Connections
TYPE REF DESCRIPTION HOSE FOR HOSE TYPEBORE
76-221/39 1/4 NPSM(F) 3/16 For LX1.376-222/39 1/4 BSP(F) 3/16 For LX1.376-236/39 M16x1.5(F) 3/16 For LX1.376-238/39 3/8 NPSM(F) 3/16 For LX1.376-239/39 3/8 BSP(F) 3/16 For LX1.376-341/39 1/4 NPSM(F) 1/4 For LM, MA, MF, MO & RPUA1.476-342/39 1/4 BSP(F) 1/4 For LM, MA, MF, MO & RPUA1.476-343/39 M14 x 1(F) 1/4 For LM, MA, MF, MO & RPUA1.476-358/39 3/8 NPSM(F) 1/4 For LM, MA, MF, MO & RPUA1.476-359/39 3/8 BSP(F) 1/4 For LM, MA, MF, MO & RPUA1.476-303/31 Spring guard for 300 series body (above)
76-441/39 1/4 NPSM(F) 1/4 For AL, LF, LPC & LPV1.476-442/39 1/4 BSP(F) 1/4 For AL, LF, LPC & LPV1.476-458/39 3/8 NPSM(F) 1/4 For AL, LF, LPC & LPV1.476-459/39 3/8 BSP(F) 1/4 For AL, LF, LPC & LPV1.4
76-561/39 1/4 NPSM(F) 5/16 For AL, RA, LPC & LPV1.576-562/39 1/4 BSP(F) 5/16 For AL, RA, LPC & LPV1.576-570/6 1/4 BSP(M) 5/16 For AL, RA, LPC & LPV1.576-578/39 3/8 NPSM(F) 5/16 For AL, RA, LPC & LPV1.576-579/39 3/8 BSP(F) 5/16 For AL, RA, LPC & LPV1.5
76-688/39 3/8 NPSM(F) 3/8 For AB, LF, LPC, LPV1.676-689/39 3/8 BSP(F) 3/8 For AB, LF, LPC, LPV1.676-691/39 1/4 NPSM(F) 3/8 For AB, LF, LPC, LPV1.676-692/39 1/4 BSP(F) 3/8 For AB, LF, LPC, LPV1.6
76-761/39 1/4 NPSM(F) 5/16 For MA, MO, RPUA, LM & LMC1.576-762/39 1/4 BSP(F) 5/16 For MA, MO, RPUA, LM & LMC1.576-778/39 3/8 NPSM(F) 5/16 For MA, MO, RPUA, LM & LMC1.576-779/39 3/8 BSP(F) 5/16 For MA, MO, RPUA, LM & LMC1.5
76-888/39 3/8 NPSM(F) 3/8 For MA, MO & RPUA1.6 76-889/39 3/8 BSP(F) 3/8 For MA, MO & RPUA1.676-891/39 1/4 NPSM(F) 3/8 For MA, MO & RPUA1.676-892/39 1/4 BSP(F) 3/8 For MA, MO & RPUA1.6
Low pressure nuts/tails/ferrulesH-12-7 Ferrule for hose up to 11.5mm ODH-14-8 Ferrule for hose up to 13.5mm ODH-16-11 Ferrule for hose up to 15.5mm ODH-19-14 Ferrule for hose up to 18.5mm OD
S-144 Hose tail for 1/4 hose F104 1/4 BSP Nut for 5/16 hose tail & 1/4 hose tailS-109 Hose tail for 5/16 hose 176-009 3/8BSP nut (nickled)S-100 Tail for 3/8 nut 1/4 hose
C-13-K100 O clip for 12.5mm OD hose (Pack 100)C-14-K100 O clip for 14.0mm OD hose (Pack 100)C-16-K100 O clip for 16.0mm OD hose (Pack 100)
P-240-K20 Push in fitting 1/4 BSP pack 20 for 1/4 hoseP-241-K20 Push in fitting 3/8 BSP pack 20 for 3/8 hose
PXC058BK Tubing cutter (illustrated)
Reusable couplings for low pressure (60 Bar)brass nickel plated for air and low pressure fluidhoses with stainless steel wetter section.
Air Controls
TYPE REF DESCRIPTION
Air Regulators78-210/0 Mini gun mounted air flow regulator 1/4 BSP(F) x 1/4 BSP(M)
C/w glass fronted gauge.
Quick Detach Hi-Flo Air Couplings & Tails50-401 Quick detach doubleacting coupling1/4 BSP male *
(Plastic sleeve)50-402 Quick detach doubleacting coupling 9mm hose tail *
(Plastic sleeve)50-407 Quick detach hi-flo air coupling 1/4 BSP(M) connection *50-427 Quick detach hi-flo air coupling 9mm tail connection *50-437 Quick detach hi-flo air coupling 1/4 BSP(F) connection *50-447 QD air connection 1/2 BSP M *50-408 QD air connection plug 1/4 BSP(F) *50-409 QD air connection plug 1/4 BSP(M) *50-410 QD air connection plug 9mm tail connection *50-417 QD air valve 1/8 BSP(M) connection *50-418 QD air connection plug for 6mm bore hose *
74-330 LP 2 outlet air connector Y with ball valves 1/4 BSP(F) x 2 x 1/4 BSP(M)
74-301.4 LP 3 outlet fluid Y connection, swivel nut 3/8 BSP(F) x 3 x 3/8 BSP fixed(one x 3/8 BSP plug included).
FM-40-03-W Air filter regulator 1/4BSP inlet. Outlet 0-150psi max. c/w Gauge and mounting bracket. Lockable with semi automatic drain and metal bowl guard.
2020-2545 Mini air filter regulator 1/4 BSP inlet - 1 x 1/4BSP(F) outlet c/w Gauge,Polycarbonate bowl with semi automatic drain
50-407
74-330 74-301.4
2020-2545
FM-40-03W
78-210/0
Textile Braided Hydraulic Hose
High Quality - Swiss Manufactured
Provides Outstanding Performance for aWide Range of Applications.
NY Series
Exitflex have for more than a quarter of acentury specialised in and developedthermoplastic hose construction. Thisexperience provides you with high quality hosesbenefiting from being lightweight, flexible andhaving long lasting durability.
Already known around the world as a leadingmanufacturer of paint spray hoses, Exitflex isnow ready to serve the needs of the industrialhose market with the NY product range.
Standard range includes hoses suitable for:
• Hydraulics - Low to Medium, Medium and High Pressure
• Lubrication & Greasing Lines
• Solvent & Chemical Lines
• Water Cleaning
• Gases & Compressed Air
• Servo Controls
• Agricultural Equipment
• Machine Tools
• Fork Trucks (Single & twin lines)
• Air Conditioning
• Plus many more....
Please contact us for further details or to discuss your requirements -telephone, fax or e-mail. (See inside cover for details)
Textile Braided Hydraulic Hose
1.3 3/16 8 85 33 Bk PA PA 1 Textile Low Pressure Hydraulic 1.4 1/4 9.8 85 47 Bk PA PA 1 Textile Lubrication Solvent Lines.1.5 5/16 12.2 85 67 Bk PA PA 1 Textile Compiles with Din 20.0211.6 3/8 13.7 85 75 Bk PA PA 1 Textile (2TE). Non Pin-Pricked 1.8 1/2 17.7 70 117 Bk PA PA 1 Textile cover for gas applications1.10 5/8 21.3 70 157 Bk PA PA 1 Textile recommend pin-pricking1.12 3/4 24.4 50 175 Bk PA PA 1 Textile the cover.
1.2 1/8 6.6 150 30 Bk PE PU 1 Textile Lubrication and greasing1.25 5/32 7.9 150 36 Bk PE PU 1 Textile servo control systems1.3 3/16 9.3 150 54 Bk PE PU 1 Textile hydrostatic transmission drain 1.4 1/4 10.9 125 72 Bk PE PU 1 Textile line for machine tools and1.5 5/16 12.8 115 93 Bk PE PU 1 Textile hydraulic equipment complies1.6 3/8 14.6 95 112 Bk PE PU 1 Textile with and exceeds SAE 100 R31.8 1/2 18.1 85 154 Bk PE PU 1 Textile Din 20.021 (2TE & 3TE)
cover is pin-pricked.
2.4 1/4 11.5 210 78 Bk PA PU 2 Textile Medium pressure hydraulic2.5 5/16 14.2 175 115 Bk PA PU 2 Textile solvent lines. Lubrication2.6 3/8 15.6 160 135 Bk PA PU 2 Textile CO2 Carbon Dioxide and LPG 2.8 1/2 20.2 140 197 Bk PA PU 2 Textile gas lines. SAE 100 R72.12 3/4 27.2 85 280 Bk PA PU 2 Textile pin-pricked IS0 3949
BS4983: 1973
1.4 1/4 9.8 100 46 Bk PA PA 1 Textile Low/medium pressure 1.5 5/16 12.2 100 66 Bk PA PA 1 Textile hydraulic also low/medium
pressure water cleaning
2.2 1/8 6.8 210 34 Bk PE-E PU 2 Textile SAE 100 R7 150 39492.25 5/32 8.3 240 49 Bk PE-E PU 2 Textile BS 4983: 1984 Type 1 2.3 3/16 9.7 210 63 Bk PE-E PU 2 Textile Din 24951 medium pressure2.4 1/4 12.1 215 97 Bk PE-E PU 2 Textile hydraulics greasing, lubrication.2.5 5/16 13.8 190 116 Bk PE-E PU 2 Textile Agricultural equipment fork 2.6 3/8 16.1 160 157 Bk PE-E PU 2 Textile trucks machine tools and 2.8 1/2 19.4 140 199 Bk PE-E PU 2 Textile similar. Cover is pin-pricked.
1.3 3/16 9.0 350 51 Bk PE-E PU 1 Aramid SAE 100 RD IS0 3949 1.4 1/4 12.3 350 105 Bk PE-E PU 1 Aramid BS 4983: 1984 Type 1 1.5 5/16 13.8 350 113 Bk PE-E PU 1 Aramid Din 24951 high pressure 1.6 3/8 16.0 275 151 Bk PE-E PU 1 Aramid hydraulic solvent chemical1.8 1/2 19.5 240 198 Bk PE-E PU 1 Aramid lines which meet SAE
standard J517D sectionR8 mixed gas applicationscover is pin-pricked
RE
F
ID OD
(mm
)
MW
P (
BA
R)
WE
IGH
T P
ER
ME
TR
E (
g/m
)
STA
ND
AR
D
CO
LO
UR
S
INN
ER
TU
BE
CO
VE
R
BR
AID
ING
AP
PL
ICA
TIO
N
NY
223
NY
343
NY
321
NY
347
NY
328
The NY Hose programme is designed to provide high quality and a full range for most applications.Welded Twin Hoses available at price of hoses + 10%.Special colours can be produced subject to volume NB: All hoses in this listing are non-conductive. NY 343p is also available with a Polyamid Inner Tube.
HYDRAULIC DUTY
NY
PAINT SPRAY . HYDRAULICS . WATER JETTING
HIGH PRESSURETHERMOPLASTICHOSES
High Pressure Thermoplastic Hose
Technology leaders
Swiss manufacturing know how
High value
Flexible yet hard wearing
Hoses for most applications
Exitflex Programme
EXITFLEX high pressure Thermoplastic Hoses are suitable for:-
HYDRAULICS, WATER JETTING and PAINT SPRAYING
EXITFLEX take particular care with the braiding technique of theirhose range. The technologies employed provide accurate controlover the characteristics required for different hose grades.
Wire braided reinforcement is of woven high tensile carbon steelbraids which give the hose its great strength and ensure 100%electrical continuity throughout the hose. High specification textilebraided hoses are also in the range for use where conductivity isnot required.
Top quality materials used in the manufacture of EXITFLEX hoses,combined with Swiss know how, gives an extra strong light weighthose having excellent abrasion and cover wear resistance inaddition to tolerance to a great many chemicals, solvents and water.
Textile braided hoses are available both in conductive and non-conductive varieties. The range in particular has excellent lay flatcharacteristics and superior pulsation absorption capabilities.
EXITFLEX is suitable for continuous use with many solvents,however it is recommended that final selection should be made after consulting the EXITFLEX chemical resistance chart or afterconsultation with your EXITFLEX distributor.
Inner Tube
Wire Reinforcement
Textile Interlayer(Grade PA2, EX2)
Wire Reinforcement(Grade PA2, EX2)
Outer Cover
EXITFLEX are major suppliers to the paint spray industry with the finest range of products available in themarket place today.
Call us today to see what we can can do for you
High Pressure Hoses
HYDRAULICS. WATERJETTING. GAS
AEP1.3 3/16” 9.0 300 56 Bk PE PU 1 x Textile Gas/Hydraulic (perf)Non conductive
DP 1.3 3/16” 9.2 250 85 Br PE PU 1 x C.Steel Drain Cleaning
ESP 2.4 1/4” 15.8 254 300 Bk PE PU 2 x St.Steel Gas/Hydraulic(perf)ESP 2.8 1/2” 21.0 204 640 Bk PE PU 2 x St.Steel Gas/Hydraulic(perf)
EX 1.3 3/16” 9.5 350 105 Bk PE PU 1 x C Steel Hydraulic/WaterjettingEX 1.4 1/4” 11.7 325 165 Bk PE PU 1 x C Steel Hydraulic/WaterjettingEXP 1.4 1/4” 11.7 325 165 Bk PE PU 1 x C Steel Hydraulic/Gas (perf)EX 1.6 3/8” 15.8 250 240 Bk PE PU 1 x C Steel Hydraulic/WaterjettingEX 1.8 1/2” 18.5 200 310 Bk PE PU 1 x C Steel Hydraulic/WaterjettingEX2.4 1/4” 14.0 450 300 Bk PE PU 2 x C Steel Hydraulic/WaterjettingEX 2.6 3/8” 17.0 400 440 Bk PE PU 2 x C Steel Hydraulic/WaterjettingEX 2.8 1/2” 21.0 350 540 Bk PE PU 2 x C Steel Hydraulic/WaterjettingEX 2.12 3/4” 30.2 275 950 Bk PE PU 2 x C Steel Hydraulic/Waterjetting
HD 2.4 1/4” 16.6 675 230 Rd PA PU 1 x C Steel + Hydraulic/Heavy Duty1 x Aramid
HDP 2.4 1/4” 16.6 675 230 Rd PA PU 1 x C Steel + Hydraulic/Gas (perf)1 x Aramid
HD 2.6 3/8” 17.5 580 325 Rd PA PU 1 x C Steel + Hydraulic/Heavy Duty1 x Aramid
HX 2.8 1/2” 22.0 250 290 Rd PE PU 2 x Textile Hydraulic/WaterjettingNon conductive
HY 1.7 6.7 11.0 250 125 Bk PE-E PU 1 x C Steel HydraulicHY 1.8 8.0 13.7 250 190 BK PE-E PU 1 x C Steel Hydraulic
JET 1.3 3/16” 9.8 400 120 Bk PE-E PU 1 x C Steel Waterjetting
PAP 2.4 1/4” 14.0 450 300 Bn PA PU 2 x C Steel Hydraulic/Gas (perf)
RE
F
ID OD
(mm
)
MW
P
WE
IGH
T P
ER
ME
TR
E (
g/m
)
STA
ND
AR
D
CO
LO
UR
S
INN
ER
TU
BE
CO
VE
R
BR
AID
ING
AP
PL
ICA
TIO
N
Extras & Special Processes* Asterisked products are special order non stock lines. Minimum quantity may apply.
Reels There is a charge per reel for all products shipped on a reel.Reels are returnable for full credit, return carriage not credited.
Pin Prick Cover Add 5% to price.Welding 2 hoses Add 10% to price of hoses
H.R.S. Heat resistant additive. Add 5% to price.H.S. Hydrolized additive. Add 5% to price.
Swage and control ExtraContinuous Or specified unbroken lengths. Add 10% to price.
Printing All hoses are printed EXITFLEX as standard. Special print may be possible subject to a minimum quantity of 1000 metres and will be charged per character set up charge.
Special Colours Minimum Quantity 500metres upon order acceptance.NB Lead time will be extended for special colours.
Safety Ratio Hoses are quoted at a 4:1 Safety Ratio with the exception of AEP, ESP which are quoted at a 5:1 Safety Radio.
Conductivity All hoses listed on P.14 and 15 are conductive except where stated otherwise.
High Pressure Hoses
PAINT SPRAY DUTY
HD 2.4 1/4” 13.6 700 225 Rd PA PU 1 x C Steel H.D / PaintSpray1 x Aramid
HD 2.6 3/8” 17.5 560 325 Rd PA PU 1 x C Steel H.D / PaintSpray1 x Aramid
HD 2.8 1/4” 22.0 450 565 Rd PA PU 1 x C Steel H.D / PaintSpray1 x Aramid
HD 2.12 3/4” 32.0 375 785 Rd PA PU 1 x C Steel H.D / PaintSpray1 x Aramid
KX 2.3 3/16” 10.2 235 75 Bl PA PU 2 x Textile PaintSpray PulsatingKX 2.4 1/4” 12.3 227 95 Bl PA PU 2 x Textile PaintSpray PulsatingKX 2.6 3/8” 16.8 225 190 Bl PA PU 2 x Textile Electric Piston Pumps
PA 1.2 1/8” 6.9 350 60 Bn PA PU 1 x C Steel HP PaintsprayPA 1.3 3/16” 9.3 350 105 Bn PA PU 1 x C Steel HP PaintsprayPA 1.4 1/4” 11.7 325 165 Bn PA PU 1 x C Steel HP PaintsprayPA 1.6 3/8” 15.5 250 240 Bn PA PU 1 x C Steel HP PaintsprayPA 1.8 1/2” 18.5 200 310 Bn PA PU 1 x C Steel HP PaintsprayPA 2.4 1/4” 14.0 450 300 Bn PA PU 2 x C Steel HP PaintsprayPA 2.6 3/8” 17.5 400 440 Bn PA PU 2 x C Steel HP PaintsprayPA 2.8 1/2” 21.0 350 540 Bn PA PU 2 x C Steel HP PaintsprayPA 2.12 3/4” 30.2 275 950 Bn PA PU 2 x C Steel HP Paintspray
PAT 2.4 1/4” 12.9 425 200 Bn PA PU 1 x C Steel + HP Paintspray1 x Textile
PAT 2.6 3/8” 17.8 325 325 Bn PA PU 1 x C Steel + HP Paintspray1 x Textile
KMW 2.3 (KX2.3 + MO + 14) Welded Twin Bl + Bn PA PU 2 x Textile AAA Paintspray
PR 1.3 3/16” 9.3 270 110 Bk PA PU 1 x C Steel Paintspray(Electric Diaphragm Pumps)
PR 1.4 1/4” 11.7 270 165 Bk PA PU 1 x C Steel Paintspray(Electric Diaphragm Pumps)
SX 2.6 3/8” 17.8 250 200 Bl PA PU 2 x Textile Paintspray(Electric Piston Pumps)
TC 1.2 1/8” 6.9 350 85 Bk FEP140 PU 1 x C Steel MultipurposeTC 1.3 3/16” 9.3 350 125 Bk FEP140 PU 1 x C Steel MultipurposeTC 1.4 1/4” 11.7 325 190 Bk FEP140 PU 1 x C Steel MultipurposeTC 1.6 3/8” 15.3 250 270 Bk FEP140 PU 1 x C Steel MultipurposeTC 1.8 1/2” 18.5 200 340 Bk FEP140 PU 1 x C Steel MultipurposeTC 2.8 1/2” 21.5 350 580 Bk FEP140 PU 2 x C Steel MultipurposeTC 2.12 3/4” 30 275 1000 Bk FEP140 PU 2 x C Steel Multipurpose
WE 2.3 3/16” 11.5 550 140 TrBn PA PU Aramid/Steel Safety WhipendWE 2.4 1/4” 13.6 550 170 TrBn PA PU 2 x C Steel Safety Whipend
(paintspray)
RE
F
ID OD
(mm
)
MW
P
WE
IGH
T P
ER
ME
TR
E (
g/m
)
STA
ND
AR
D
CO
LO
UR
S
INN
ER
TU
BE
CO
VE
R
BR
AID
ING
AP
PL
ICA
TIO
N
Colour Code: Bl = blue; Bn = blue navy; Bk = black; Rd = red; Br = bronze; Tr = transleucentNB: All paint spray hoses both textile and wire braided are conductive.
High Pressure Hose Assemblies
The assemblies shown on these pages represent the most commonly purchased lengths. Exitflex are pleased to offerhose assemblies to any length. Please call for a quotation on any lenghts not shown.
NB: PRICES INCLUDE ALL FITTINGS. IMPORTANT PLEASE SPECIFY THREADS REQUIRED
Welded Twin HosesKMW 2.3 Welded twinned hose assemblies for Air Assisted Airless systems comprising 2 textile 3/16 fluid hose
plus low pressure air hose. MO 1/4 bore. MWP fluid 235 Bar.
PMW 1.3 Welded twin hose assemblies for Air Assisted Airless systems comprising 1 wire 3/16 fluid hoseplus low pressure 1/4 air hose. MWP fluid 270 Bar.
Standard lengths shown others to order
NB. KMW 2.3 has conductive fluid hose, non conductive air hose
PA Wire Braided Hoses For Pneumatic Airless SystemsPA1.2 PA1.3 PA1.4 PA1.6 PA1.8 PA2.4 PA2.6 PA2.8
1/8 bore 3/16 bore 1/4 bore 3/8 bore 1/2 bore 1/4 bore 3/8 bore 1/2 boreMWP Bar 350 350 325 250 200 450 400 350
1
Standard lengths 1, 2 ,3, 5, 7.5, 10 and 15 metres - other lengths to order
PAT Hoses With 1 Wire and 1 Textile Braid for Pneumatic Airless SystemsPAT2.4 PAT2.61/4 bore 3/8 bore
MWP Bar 425 325
Standard lengths 5, 7.5, 10 and 15 metre other lengths to order
HD Extra Pressure Heavy Duty Paint Spray Hose WE Safety WhipendsHD2.4 HD2.6 WE 2.3 WE 2.4
1/4 bore 3/8 bore 3/16 bore 1/4 boreMWP Bar 700 560 550 MWP Bar 550
Standard lengths 7.5, 10 and 15 metre Standard length 3 metre other lengths to order other lengths to order
WE safety whipends are factory assembled andproof tested. All assemblies come with 1/4
NPSM(F) x 1/4 NPT(M) stainless steel couplingspermanently swaged to the hose - guaranteed!
IMPORTANTPlease specify clearly your end connection threadrequirements
NB: All hoses listed on pages 16-17 both wire and textile braided are conductive
High Pressure Hose Assemblies
PR Wire Braided Pulsating Hoses For Diaphragm Electrical PumpsPR1.3 PR1.4
3/16 bore 1/4 boreMWP Bar 270 270
5 Metre Standard lengths shown others to order7.5 Metre10 Metre15 Metre
SX Hose Pulsating Textile Braided Hoses For Piston Electric PumpsSX2.6
3/8 boreMWP Bar 225
5 Metre Standard lengths shown others to order7.5 Metre15 Metre
KX Hose Expanding/Textile Braided Pulsating Hoses for Electric Piston PumpsKX2.3 KX2.4
3/16 bore 1/4 boreMWP Bar 235 235
5 Metre Standard lengths shown others to order7.5 Metre15 Metre
TC Hose Multi Purpose Teflon Cored Wire Braided HosesTC1.4 TC1.6
1/4 bore 3/8 boreMWP Bar 275 250
7.5 Metre Standard lengths shown others to order10 Metre15 Metre
JET and EX Hoses Wire Braided Hoses For Water JettingJET 1.3 EX 2.4 EX 2.8
NB MWP SHOWN AT 4:1 & 2.5:1 RATIO 3/16 bore 1/4 bore 1/2 boreMWP Bar 400/560 450/720 350/560
3 Metre Standard lengths shown others to order7 Metre10 Metre
--
DP Copper Drain Wire Braided Hoses For Drain CleaningDP1.3
NB MWP SHOWN AT 4:1 RATIO AND 2.5:1 RATIO 3/16 boreMWP Bar 250/400
7 Metre Standard lengths shown others to order10 Metre15 Metre20 Metre
Hose SleevingPVCT 2/500 PVC sleeve 2" Approx. 500ft roll 500 gaugePVCT 3/500 PVC sleeve 3" Approx. 500ft roll 500 gaugePVCT 3/1000 PVC sleeve 3" Approx. 250ft roll 1000 gaugePVCT 8/500 PVC sleeve 8" Approx. 500ft roll 500 gaugeGW30 BK Polyester braid 25/30mm 50 metre roll Per metreGW40 GR Polyester braid 40/60mm 50 metre roll Per metre
Reusable Couplings for High Pressure Hose
(Bichromated Steel)
Reusable Couplings For Single (1) Braided Hose77-001/2 * 1/4 BSP(F) swivel (1/4)77-001/38 Ditto in stainless steel nipple. Black nut. Nickel body77-011/1 * 3/8 BSP(F) swivel (3/8)77-017/2 * 1/4 NPSM(F) swivel (1/4)77-017/38 Ditto in stainless steel nipple. Black nut. Nickel body77-019/1 1/4 NPT(M) (3/8)77-020/1 1/4 NPT(M) (1/4)77-021/2 1/4 BSP(F) swivel (1/4)77-022/1 JIC 1/2 x 20(F) swivel (3/8)77-023/1 M16 x 150(F) swivel77-024/2 1/4 NPSM(F) swivel (1/4)77-026/1 3/8 NPSM(F) swivel (3/8)77-030/1 3/8 NPT(M) (3/8)77-032/1 M16 x 150(F) swivel (1/4)77-034/2 M16 x 150(F) swivel (3/8)77-036/1 JIC 1/2 x 20(F) swivel (1/4)77-040/1 1/4 BSP(F) swivel (1/8)77-040/38 Ditto in stainless steel nipple. Black nut. Nickel body77-042/1 * 1/4 NPSM(F) swivel (1/8)77-042/38 Ditto in stainless steel nipple. Black nut. Nickel body77-044/1 JIC 1/2 x 20(F) swivel (1/8)77-046/1 M16 x 150(F) swivel (1/8)77-050/2 * 1/4 BSP(F) swivel (3/16)77-050/38 Ditto in stainless steel nipple. Black nut. Nickel body77-052/2 * 1/4 NPSM(F) swivel (3/8)77-052/38 Ditto in stainless steel nipple. Black nut. Nickel body77-054/1 JIC 1/2 x 20(F) swivel (3/16)77-056/2 M16 x 150(F) swivel (3/16)77-068/1 JIC 3/4 x 16(F) swivel (3/8)77-071/2 1/4 BSP(F) swivel (SX 1/4)77-072/2 JIC 1/2 x 20 swivel (SX 1/4)77-073/1 M16 x 150(F) swivel (SX 1/4)77-074/2 1/4 NPSM(F) swivel (SX 1/4)
Reusable Couplings For Double (2) Braided Hose77-211/2 * 3/8 BSP(F) swivel (3/8 DB)77-226/2 * 3/8 NPSM(F) swivel (3/8 DB)77-230/1 3/8 NPT(M) (3/8 DB)77-268/2 3/4 x 16JIC(F) swivel (3/8 DB)
Spring Guards For Hose Assemblies34-010/31 * Spring handle and rubber34-013/31 * Spring guard (PX 1.3/PA+PR 1.3)34-014/31 * Spring guard (PX 1.4/PA+PR 1.4, SX 2.4))34-016/31 Spring guard (PA 1.6)34-023/31 Spring guard (SX2.3)34-024/31 Spring guard (PX 2.4+ST 1.4)34-026/31 * Spring guard (PA+PAT 2.4)34-027/31 * Spring guard (PA,PAT,SX 2.6)34-040/3 Spring guard (SR 1.8)34-041/3 * Spring guard (SR 1.12)34-042/3 * Spring guard (SR 1.16)
* Stocked lines, others to order
Unions, Ferrules & Swivels
Water Fittings & UnionsTYPE REF DESCRIPTION74-617/0 Union 1/4 BSP(F) x M22 x 150(F) swivel nut74-618/0 Union 3/8 BSP(F) x M22 x 150(F) swivel nut74-621/0 Locking nut M22 x 150(F) (water)74-632/1 Union 1/4 BSP(M) x M22 x 150(M)74-633/1 Union 3/8 BSP(M) x M22 x 150(M)74-636/11 Nipple for 1/4 ID hose (water)74-637/11 Nipple for 3/8 ID hose (water)74-640/22 Nitrile "O" ring (water)74-641/11 Nut HP 7/8 x 9 UNC
High Pressure Swage FerrulesBichromated Mild SteelTYPE REF DESCRIPTION
75-800/51 F1.2(10,3-4,2-6-17,6)75-801/51 F2.275-803/51 F1.3 (DF1.3)75-805/51 F1.3 (13,7-9,7-23,5)75-806/51 F2.3 (15,4-11,4-9-23,5)75-807/53 F1.3 (smooth non slotted) JET1.375-808/51 F1.3 (11,5-9,7-8,2) DP1.375-810/51 F1.4 (17,4-12,4-29)75-812/51 F2.4 (19,5-14,5-29) 5/16 (1-5)75-815/51 F2.4 (18,6-13,6-29) SX 2.475-820/51 F1.6 (20,8-15,8-14-35) 5/16 (2.5)75-826/51 F2.6 (24.2-18,6-14,2-35)75-830/51 F1.8 (23,8-19,1-17,4-36,5)75-835/51 F2.8 (27,8-22,8-17,4-36,5)75-837/51 F1.1275-838/51 F2.1275-860/51 F1.4 (16.5-11,5-11,5-29) PAM1.475-870/51 F1.6 (20-15-14,5-35) PAM1.6NB Ferrules in stainless steel by special enquiry. Selected sizes Extended delivery
High Pressure SwivelsTYPE REF DESCRIPTION70-110/2 1/4 BSP(M) x 1/4 BSP(F) 517 Bar MWP70-220/2 1/4 NPS(M) x 1/4 NPSM(F) 517 Bar MWP70-220/34 1/4 NPS(M) x 1/4 NPSM(F) ST.STEEL 517 Bar MWP70-290/1 1/4 NPS(M) x M14x1(M) 517 Bar MWP70-440/2 3/8 BSP(M) x 3/8 BSP(F) 517 Bar MWP70-550/2 3/8 NPS(M) x 3/8 NPSM(F) 517 Bar MWP70-520/1 3/8 NPS(M) x 1/4 NPSM(F) 517 Bar MWP70-900/1 1/4 NPS(M) x M18x1.5(M) (Ran-Gema) 517 Bar MWPThere is an additional range of Swivels, Filters and Swivel Filters available to special order.Please enquire about price and availability
High Pressure Stainless Steel Z SwivelsTYPE REF DESCRIPTION70-911/1 1/4BSP(M) x 1/4BSP(F) 517 Bar MWP70-922/2 1/4NPSM(M) x 1/4NPSM(F) 517 Bar MWP
Hose Inserts Male or Female Without Ferrule
Bichromated Mild SteelTYPE REF DESCRIPTION75-001/1 1/4 BSP(F) swivel (1/4) s/pl 1975/001/37 Ditto stainless black nut75-003/1 1/4 BSP(F) swivel (3/8) s/pl 1975-007/1 3/8 BSPM (3/8)75-008/1 3/8 BSP(F) swivel (1/4)75-009/1 1/4 BSP(M) (1/4)75-010/1 3/8 NPSM(F) swivel (1/4)75-011/1 3/8 BSP(F) swivel (3/8)75-011/37 Ditto stainless black nut75-012/1 1/4 NPT(M) (1/8)75-013/1 1/4 NPT(M) (3/16)75-014/1 1/4 NPS(M) (1/8)75-015/1 1/4 NPS(M) (3/16)75-017/1 1/4 NPSM(F) swivel (1/4) s/pl 1975-017/37 Ditto in stainless steel black nut75-018/1 1/4 NPSM(F) swivel (1/4) s/pl 1775-019/1 1/4 NPSM(F) swivel (3/8) s/pl 1975-020/1 1/4 NPT(M) (1/4)75-021/1 Pipe 6 x 17mm (1/8) O75-026/1 3/8 NPSM(F) swivel (3/8)75-026/37 Ditto in stainless steel black nut75-030/1 3/8 NPT(M) (3/8)75-032/1 M16 x 150(F) swivel (1/4)75-032/37 Ditto in stainless steel black nut75-034/1 M16 x 150(F) swivel (3/8)75-036/1 JIC 1/2 x 20(F) swivel (1/4)75-037/1 1/8 BSP(F) swivel (1/8)75-038/1 JIC 1/2 x 20(F) swivel (3/8)75-040/1 1/4 BSP(F) swivel (1/8)75-042/1 1/4 NPSM(F) swivel (1/8) s/pl 1975-042/37 Ditto in stainless steel black nut75-043/1 1/4 MPSM(F) swivel (1/8) s/pl 1775-044/1 JIC 1/2 x 20(F) swivel (1/8)75-045/1 1/8 NPSM(F) swivel 1/875-046/1 M16 x 150(F) swivel (1/8)75-048/1 1/8 BSP(M) (1/8) s/pl 1075-049/1 1/4 BSP(M) (1/8)75-050/1 1/4 BSP(F) swivel 3/16 s/pl 1975-050/37 Ditto in stainless steel black nut75-051/1 Pipe 6 x 22mm (3/16) 075-052/1 1/4 NPSM(F) swivel (3/16) s/pl 1975-052/37 Ditto in stainless steel black nut75-053/1 1/4 NPSM(F) swivel (3/16) s/pl 1775-054/1 JIC 1/2 x 20(F) swivel (3/16)75-055/1 1/8 BSP(M) (3/16)75-056/1 M16 x 150(F) swivel (3/16)75-056/37 Ditto in stainless steel black nut75-057/1 M16 x 150(M) (3/16)75-059/1 1/4 BSP(M) (3/16) s/pl 175-062/1 M18 x 150(F) swivel (1/4)75-063/1 M18 x 150(F) swivel (5/16)75-064/1 M18 x 150(F) swivel (3/8)
Hose Inserts Male or Female Without Ferrule
Bichromated Mild SteelREFERENCE DESCRIPTION75-065/1 Pipe 12 x 20mm (3/8) O75-066/1 1/8 NPT(M) (3/8)75-067/1 1/8 NPT(M) (3/16)75-068/1 JIC 3/4 x 16(F) swivel (3/8)75-070/1 JIC 9/16 x 18(M) (1/8)75-071/1 JIC 9/16 x 18(M) (3/16)75-072/1 JIC 9/16 x 18(M) (1/4)75-073/1 JIC 9/16 x 18(M) (3/8)75-074/1 JIC 9/16 x 18(F) swivel (3/8)75-075/1 JIC 1/2 x 20(M) (3/8)75-076/1 JIC 7/16 x 20(F) swivel (1/8)75-077/1 JIC 7/16 x 20(F) swivel (3/16)75-080/1 JIC 7/16 x 20(F) swivel (1/4)75-081/1 1/2 NPSM(F) swivel (1/2)75-082/1 1/2 BSP(F) swivel (1/2)75-084/1 JIC 3/4 x 16(F) swivel (1/2)75-085/1 1/2 NPT(M) (1/2)75-088/43 JIC 9/16 x 18(M) (1/2) stainless steel75-089/1 1/2 BSP(M) (1/2)75-090/1 1/4 BSP(F) swivel (5/16) s/pl 1975-092/1 1/4 NPSM(F) swivel (5/16) s/pl 1975-093/1 3/8 BSP(F) swivel (5/16)75-094/1 3/8 NPSM(F) swivel (5/16)75-111/1 3/4 NPT(M) 3/475-112/1 3/4 NPSM(F) swivel (3/4)75-202/1 Round 1/8 BSP(M) (1/8)75-203/1 Round 1/8 BSP(M) (3/16) 075-204/1 Round 1/8 BSP(M) (1/4) 075-211/1 Round 1/8 BSP(M) long (3/16) 075-227/1 Tip nipple 1/8 ID for spray gun end75-240/1 Round M6x100(M) (3/16) short75-241/1 Round M7x100(M) (3/16)75-251/1 1/4 BSP(M) flat flange (1/4) jet75-258/30 Round 1/8 BSP(M) (3/16) short stainless75-401/1 1/4" BSP(F) insert for PAM 6mm75-411/1 3/8" BSP(F) insert for PAM 9mm75-417/1 1/4" NPSM(F) insert for PAM 6mm75-426/1 3/8" NPSM(F) insert for PAM 9mm
Left Hand Thread Nipple75-617/1 1/4 NPSM(F) SWIVEL (17) (1/8)L.H Old ref 75-31775-618/1 1/4 NPSM(F) SWIVEL (17) (3/16)L.H Old ref 75-31875-619/1 1/4 NPSM(F) SWIVEL (17) (1/4) L.H Old ref 75-31975-620/1 1/4 NPSM(F) SWIVEL (17) (5/16) L.H Old ref 75-32075-621/1 1/4 NPSM(F) SWIVEL (17) (3/8) L.H Old ref 75-321
Couplings & Adaptors - Male x Male
PLEASE NOTEWhere stated Swivel Nut. These are not high-pressure swivels. Where a highpressure swivel is required order a 70 or 71 series item.All swivel nuts in this section are not swiveling once tightened down.Popular sizes indicated thus ____
BSP Male x BSP Male 78-034/1 ____ 1/4 BSP(M) x 3/8 BSP(M) coned Intl Hex Drive74-001/1 ____ 1/4 BSP(M) x 1/4 BSP(M)74-001/30 ____ 1/4 BSP(M) x 1/4 BSP(M) stainless74-002/1 ____ 1/4 BSP(M) x 3/8 BSP(M)74-002/30 ____ 1/4 BSP(M) x 3/8 BSP(M) stainless74-003/1 ____ 3/8 BSP(M) x 3/8 BSP(M)74-003/30 ____ 3/8 BSP(M) x 3/8 BSP(M) stainless74-004/1 3/8 BSP(M) x 1/2 BSP(M)74-004/30 3/8 BSP(M) x 1/2 BSP(M) stainless74-005/1 1/2 BSP(M) x 1/2 BSP(M)74-005/30 1/2 BSP(M) x 1/2 BSP(M) stainless174-811/30 1/8 BSP(M) x 1/4 BSP(M) coned stainless Int Hex Drive74-406/15 1/4 BSPT(M) x 1/4 BSP(M) coned nickel plated brass Hexagonbody74-007 1/4 BSP(M) flat faced x 1/4 BSP(M) coned stainless Int Hex Drive
NPS/NPT Male x NPS/NPT Male 74-010/1 1/4 NPT(M) short x 3/8 NPT(M) W74-011/1 ____ 1/4 NPT(M) x 1/4 NPT(M)74-011/30 ____ 1/4 NPT(M) x 1/4 NPT(M) stainless74-012/1 ____ 1/4 NPT(M) x 3/8 NPT(M)74-012/30 ____ 1/4 NPT(M) x 3/8 NPT(M) stainless74-013/1 ____ 3/8 NPT(M) x 3/8 NPT(M)74-013/30 ____ 3/8 NPT(M) x 3/8 NPT(M) stainless74-014/1 3/8 NPT(M) x 1/2 NPT(M)74-015/1 1/2 NPT(M) x 1/2 NPT(M)74-016/1 ____ 1/4 NPS(M) x 1/4 NPS(M) NLA use 74-011/174-017/1 ____ 1/4 NPS(M) x 3/8 NPS(M) NLA use 74-012/174-018/1 ____ 3/8 NPS(M) x 3/8 NPS(M) NLA use 74-013/1
NPS/NPT Male x BSP/BSPT Male 74-062/1 1/4 NPT(M) x 1/4 BSP(M)74-063/1 3/8 NPT(M) x 1/4 BSP (M)
JIC Male x JIC Male 74-021/1 JIC 1/2 x 20(M) x JIC 1/2 x 20(M)74-022/1 JIC 1/2 x 20(M) x JIC 3/4 x 16(M)74-023/1 JIC 3/4 x 16(M) x JIC 3/4 x 16(M)
Metric Male x Metric Male 74-031/1 ____ M16 x 150(M) x M16 x 150(M)74-031/30 ____ M16 x 150(M) x M16 x 150(M) stainless
Metric Male x BSP Male 74-060/1 M16 x 150(M) x 1/4 BSP(M)
Metric Male x NPS/NPT Male 74-061/1 ____ M16 x 150(M) x 1/4 NPT(M)74-064/1 M16 x 150(M) x 3/8 NPT(M)
Couplings & Adaptors - Male x Female
BSP Male x BSP Female
78-035/1 1/4" BSP (M) flat faced x 1/4 BSP(F) swivel zinc plated int hex drive 74-080/1 ____ 1/4 BSP(M) x 3/8 BSP(F) swivel nut74-080/37 1/4 BSP(M) x 3/8 BSP(F) stainless black swivel nut74-088/1 3/8 BSP(M) x 3/8 BSP(F) swivel nut74-088/37 3/8 BSP(M) x 3/8 BSP(F) stainless black swiveling nut74-089/1 1/4 BSP(M) x 1/4 BSP(F) swivel nut
BSP Male x NPSM Female 74-085/1 1/4 BSP(M) x 1/4 NPSM(F) swivel nut74-086/1 3/8 BSP(M) x 3/8 NPSM(F) swivel nut74-087/1 ____ 1/4 BSP(M) x 3/8 NPSM(F) swivel nut74-087/37 1/4 BSP(M) x 3/8 NPSM(F) stainless black swivel nut
BSP Male x JIC Female 74-081/1 ____ 1/4 BSP(M) x JIC 1/2 x 20(F) swivel nut74-082/1 3/8 BSP(M) x JIC 3/4 x 16(F) swivel nut
BSP Male x Metric Female 74-083/1 ____ 1/4 BSP(M) x M16 x 150(F) swivel nut74-083/37 ____ 1/4 BSP(M) x M16 x 150(F) stainless black nut74-084/1 3/8 BSP(M) x M16 x 150(F) swivel nut74-095/37 3/8 BSP(M) x M22 x 150(F) stainless black nut74-199/1 1/4 BSP(M) x M14 x 1(F) swivel nut
NPS/NPT Male x NPS Female74-032/1 1/4 NPS(M) x 1/4 NPSM(F) swivel nut74-033/1 3/8 NPS(M) x 1/4 NPSM(F) swivel nut74-034/1 3/8 NPS(M) x 3/8 NPSM(F) swivel nut74-036/1 3/8 NPT(M) x 1/4 NPSM(F) swivel nut74-037/1 3/8 NPT(M) x 1/2 NPSM(F) swivel nut74-038/1 1/2 NPT(M) x 1/2 NPSM(F) swivel nut74-039/1 1/4 NPT(M) x 1/4 NPSM(F) swivel nut74-040/1 1/4 NPS(M) x 3/8 NPSM(F) swivel nut74-040/37 1/4 NPS(M) x 3/8 NPSM(F) swivel nut stainless black nut
NPT Male x BSP Female 74-035/1 3/8 NPT(M) x 1/4 BSP(F) swivel nut74-045/1 ____ 1/4 NPT(M) x 1/4 BSP(F) swivel nut74-046/1 3/8 NPT(M) x 3/8 BSP(F) swivel nut74-047/1 3/8 NPT(M) x 3/8 NPSM(F) swivel nut74-048/1 1/4 NPT(M) x 3/8 BSP(F) swivel nut
NPT Male x JIC Female 74-041/1 ____ 1/4 NPT(M) x JIC 1/2 x 20(F) swivel nut74-042/1 3/8 NPT(M) x JIC 3/4 x 16(F) swivel nut
NPT Male x Metric Female 74-043/1 ____ 1/4 NPT(M) x M16 x 150(F) swivel nut74-044/1 ____ 3/8 NPT(M) x M16 x 150(F) swivel nut
Couplings & Adaptors - Male x Female
JIC Male x BSP Female 74-055/1 ____ JIC 1/2 x 20(M) x 1/4 BSP(F) swivel nut74-056/1 JIC 3/4 x 16(M) x 3/8 BSP(F) swivel nut74-057/1 JIC 1/2 x 20(M) x 3/8 BSP(F) swivel nut
JIC Male x JIC Female 74-050/1 JIC 1/2 x 20(M) x JIC 3/4 x 16(F) swivel nut
JIC Male x NPSM Female 74-051/1 ____ JIC 1/2 x 20(M) x 1/4 NPSM(F) swivel nut74-052/1 JIC 3/4 x 16(M) x 3/8 NPSM(F) swivel nut74-058/1 ____ JIC 1/2 x 20(M) x 3/8 NPS(F)nut
JIC Male x Metric Female 74-053/1 ____ JIC 1/2 x 20(M) x M16 x150(F) swivel nut74-054/1 JIC 3/4 x 16(M) x M16 x 150(F) swivel nut
Metric Male x Metric Female 74-070/1 M16 x 150(M) x M16 x 150(F) swivel nut
Metric Male x BSP Female 74-075/1 ____ M16 x 150(M) x 1/4 BSP(F) swivel nut74-076/1 M16 x 150(M) x 3/8 BSP(F) swivel nut74-198/1 M14 x 1(M) x 1/4 BSP(F) swivel nut
Metric Male x NPSM Female 74-071/1 ____ M16 x 150(M) x 1/4 NPSM(F) swivel nut74-072/1 M16 x 150(M) x 3/8 NPSM(F) swivel nut
Metric Male x JIC Female 74-073/1 ____ M16 x 150(M) x JIC 1/2 x 20(F) swivel nut74-074/1 M16 x 150(M) x JIC 3/4 x 16(F) swivel nut
Female x Female 74-151/1 Female union 1/4 BSP(F) x 1/4 BSP(F)74-152/1 Female union 1/4 BSP(F) x 3/8 BSP(F)74-153/1 Female union 3/8 BSP(F) x 3/8 BSP(F)74-161/1 Female union 1/4 NPSM(F) x 1/4 NPSM(F)74-162/1 Female union 1/4 NPSM(F) x 3/8 NPSM(F)74-163/1 Female union 3/8 NPSM(F) x 3/8 NPSM(F)
Elbows & Tees78-036/30 3/8 BSP 90° heavy duty 90° elbow, st/steel. 2 x 3/8 BSP(F)78-048/30 3/8 BSP Tee heavy duty 90° elbow, st/steel. 3 x 3/8 BSP(F)
Plugs74-311/1 Plug 1/4 NPT(M)74-313/1 Plug 3/8 NPT(M)74-315/1 Plug 1/2 NPT(M)
Other variations may be possible. Please enquire
Filter Housings & Screens
Manifold Filters36-400/12 Aluminium High Pressure Manifold Filter
400 Bar MWP incl filter. Please specify mesh (36 series/400 - page 27). 3/8 BSP inlet 1/4 BSP(M) outlet
36-301 PTFE gasket for 30-400
36-398/30 Stainless steel high pressure manifold filter 400 Bar MWP single filter 3/8 inlet,2 x 3/8 BSP(F) outlets (accepts 36 series/400 - page 27)
36-399/30 Stainless Steel High Pressure Filter 400 Bar MWPTwin filters 1/2 BSP(M) inlet and outlet (includes filter, please specify mesh.(36 series/400 - page 27)
Low Pressure Manifold Filter Assembly36-300/30 Low Pressure Manifold Filter Assembly, 100 Bar MWP
Stainless steel. Accepts 36 series/400 filter screens.3/8 BSP inlet/outlet (F)(includes filter, please specify mesh (36 series/400 - page 27)
78-217/30 Low Pressure Inline Filter Assembly, 100 barMWP. Stainless steel. Accepts 36 series/400 filter screens.3/8 BSP inlet/outlet (inline) (includes filter, please specify mesh (36 series/400 - page 27)
Filter Housings & Screens
Conventional Pressure Filters* Fully stainless steel or delrin to choice. Illustrations 36-750/20 delrin & 36-750/30 stainless steel (304)* 3/8 BSP cone seat, male inlet, 3/8 BSP cone seat female outlet.* Accepts 36 series/700 series filters. (colour coded, mesh range from 20 to 300 micron)* Lightweight - only 72g (stainless steel) & 25g (delrin)
TYPE REF DESCRIPTION SCREEN36-750/30 Filter housing 3/8BSP c/w 300 micron screen (36-760) st/st36-750/20 Filter housing 3/8BSP c/w 300 micron screen (36-760) delrin36-751/20 Filter housing 1/4BSP c/w 300 micron screen (36-760) delrin
36-760-K50 * Pack of 50 white elements 300 micron36-761-K50 * Pack of 50 blue elements 112 micron36-762-K50 * Pack of 50 red elements 80 micron36-763-K50 * Pack of 50 green elements 60 micron36-764-K50 * Pack of 50 orange elements 30 micron36-765-K50 * Pack of 50 brown elements 20 micron
78-111/34 Quick release filter housing (Non shut off)
Conventional Suction Gun Filters36-501-K10 * Suction filter Nylon 80 mesh 18 x 37mm (blue) Pack 1036-501-K100 * Suction filter Nylon 80 mesh 18 x 37mm (blue) Pack 10036-508-K10 * Suction filter 80 mesh sts screen 18 x 37mm (white) Pack 1036-508-K100 * Suction filter 80 mesh sts screen 18 x 37mm (white) Pack 100All above to fit suction tube 6.5 - 8mm diameter
36-512-K10 * Suction filter Nylon 100 mesh 28 x 42mm (yellow) Pack 1036-512-K100 * Suction filter Nylon 100 mesh 28 x 42mm (yellow) Pack 10036-515-K10 * Suction filter Nylon 165 mesh 28 x 42mm (red) Pack 1036-521-K10 * Suction filter 100 mesh sts screen 28 x 42mm (white) Pack 1036-521-K100 * Suction filter 100 mesh sts screen 28 x 42mm (white) Pack 100All above to fit suction tube 8 - 10mm diameter
Conventional Gravity Gun Filters36-531-K10 * Gravity filter Nylon 80 mesh (small blue) Pack 10
36 series/700filter screens
36-750/30
36-501
36-508
36-531
36-750/20
78-111/34
NB: Plastic Filter Housingsare non-conductive
Filter Housings & Screens
Manifold Filter Screens36 SERIES/400 MANIFOLD FILTER SCREENS FIT 36-300, 36-400, AND 36-401 PRESSURE FILTERS AND
36-45X SERIES SUCTION FILTER HOUSINGS & ARE INTERCHANGEABLE WITH GRACO36-401/34 * Manifold Filter 15 mesh screen36-403/34 * Manifold Filter 30 mesh screen36-406/34 * Manifold Filter 60 mesh screen36-410/34 * Manifold Filter 100 mesh screen36-415/34 * Manifold Filter 150 mesh screen36-420/34 * Manifold Filter 200 mesh screen36-430/34 * Manifold Filter 300 mesh screen36-440/34 * Manifold Filter 400 mesh screen
36 SERIES/600 MANIFOLD FILTER SCREENS ST/STEEL PRESSURE FILTERS FITSKREMLIN, WAGNER, BöLLHOFF & OTHERS. DIA 27mm LENGTH 114mm
36-603 ** Manifold filter Screen size No. 3 (0.08mm) 200 mesh36-604 * Manifold filter Screen size No. 4 (0.09mm) 165 mesh36-605 * Manifold filter Screen size No. 5 (0.14mm) 120 mesh36-606 * Manifold filter Screen size No. 6 (0.19mm) 86 mesh36-609 * Manifold filter Screen size No .9 (0.24mm) 66 mesh36-612 * Manifold filter Screen size No.12 (0.32mm) 50 mesh36-615 * Manifold filter Screen size No.15 (0.41mm) 40 mesh36-620 * Manifold filter Screen size No.20 (0.53mm) 30 mesh36-359/30 Support spring for all of the above
36 SERIES/100 MANIFOLD FILTER SCREENS ST/STEEL PRESSURE FILTERCOLOUR CODED FITS WIWA & HUBNER
36-103/34 * Fluid filter Nylon Core Blue 30 mesh36-105/34 * Fluid filter Nylon Core Orange 50 mesh36-107/34 * Fluid filter Nylon Core Yellow 70 mesh36-110/34 * Fluid filter Nylon Core Black 100 mesh36-115/34 * Fluid filter Nylon Core Red 150 mesh36-120/34 * Fluid filter Nylon Core White 200 mesh
In Line Filter ScreensFITS KREMLIN Ø9.5mm L 17.0mm36-1050-K10 * Filter Screen Stainless Steel Pk 10 50 mesh36-1051-K10 * Filter Screen Stainless Steel Pk 10 100 mesh36-1052-K10 * Filter Screen Stainless Steel Pk 10 200 mesh
Low Pressure FilterFor pressure feed application78-350 Stainless steel, 3/8 BSP(F) swivel nut inlet. 3/8 BSP(M) outlet 20 BAR MWP 78-351 60 mesh cone filter element (single) (white)78-352 100 mesh cone filter element (single) (yellow)
Filter Housings & Screens
Suction Filter Assemblies TYPE REF DESCRIPTION36-450/42 Suction Filter Assembly Nylon Housing 1” NPSM(F) Green36-452/42 Suction Filter Assembly Nylon Housing 3/4 NPSM(F) Orange36-453/41 Suction Filter Assembly Nylon Housing 1/2 NPSM(F) Black36-454/42 Suction Filter Assembly Nylon Housing 28x1.5mm(F) Blue36-455/42 Suction Filter Assembly Nylon Housing 15x1mm Red36-460/20 Seal for above filter assemblies
Above housings exclude 36 series/400 screen – see page 20
Suction Filter - Bell Type311000 Paint suction BELL kit -(F) M15x1 - 30 and 50 mesh disc filters312000 Paint suction BELL kit -(F)1/2” - 30 and 50 mesh disc filters314000 Cap (F) M15x1 only315000 Cap (F) 1/2” only306055 Disc filter 30 ME nylon (pack 10)306105 Disc filter 50 ME nylon (pack 10)313000 Stainless steel spring
Suction Filter - Barrel Type316000 Paint mini suction filter 30 mesh - (F) 28 x 1.5317000 Paint mini suction filter 60 mesh - (F) 28 x 1.5307030 30 mesh Mini filter net (without base)307060 60 mesh Mini filter net (without base)320000 Adaptor (M) 28x1,5 x (F) 15x1 for siphon hose321000 Base adaptor (M) 28x1,5 x (F) 3/8” for siphon hose322000 Base adaptor (M) 28x1,5 x (F) 1/2” for siphon hose323000 Base adaptor (M) 28x1,5 x (F) 3/4” for siphon hose324000 Base adaptor (M) 28x1,5 x (F) 1” for siphon hose
Disposable Spraybooth Filter PaperFor dry spray booths, white faced, pleated perforated cardboard filters, superior quality construction with strapping toensure correct fitting and spacing. Up to 98% efficiency. Made in UK. Height 0.9m (36”), Length 9.24m (30ft). Packedin threes.
Quantity1 pack of three6 packs of three plus12 packs of three plus1 pallet (50 filters)
6 packs and more are supplied carriage free.
Other types including high efficiency filters by enquiry.
Filter Housings & Screens
TYPE REF DESCRIPTION
In-line Filters36-UK-1 Interline Strainer Assembly
Includes filter (specify) 1/4 NPSM both ends36-UK-2 As above but 1/4” to 3/8” NPSM both ends36-UK-3 As above but 3/8” to 3/8” NPSM both ends
Gun Handle Filters36-030-K10 * Gun Filter 30 mesh green Pack of 1036-060-K10 * Gun Filter 60 mesh white Pack of 1036-100-K10 * Gun Filter 100 mesh yellow Pack of 1036-150-K10 * Gun Filter 150 mesh blue Pack of 1036-200-K10 * Gun Filter 200 mesh red Pack of 10
AAA Gun Handle Filters fits Optima35-030-K10 * Gun Filter 50 mesh green Pack of 1035-050-K10 * Gun Filter 80 mesh white Pack of 1035-100-K10 * Gun Filter 150 mesh yellow Pack of 1035-180-K10 * Gun Filter 300 mesh red Pack of 10
High Pressure Disc Tip Swivel Filters High Pressure Swivel With Inline Filter Assembly (incl. filter)Disc Filter to be specified 36-005 or 36-00971-110/2 1/4 BSP(M) x 1/4 BSP(F) 400 Bar WMP71-220/2 1/4 NPS(M) x 1/4 NPSM(F) 400 Bar MWP71-410/2 3/8 BSP(M ) x 1/4 BSP(F) 400 Bar MWP71-420/2 3/8 BSP(M) x 1/4 NPSM(F) 400 Bar MWP71-450/2 3/8 BSP(M) x 3/8 NPS(F) 400 Bar MWP71-480/2 3/8 BSP(M) x M16 x 150(F) 400 Bar MWP71-880/2 M16x150 (M) xM16x150 (F) 400 Bar MWP
Disc Tip Filter UnitsTYPE REF DESCRIPTION72-110/2 1/4BSP(M) x 1/4 BSP(F) Incl. filter, specify72-220/2 1/4 NPS(M) x 1/4 NPSM(F) Incl. filter, specify72-440/2 3/8 BSP(M) x 3/8 BSP(F) Incl. filter, specify72-520/2 3/8 NPS(M) x 1/4 NPSM(F) Incl. filter, specify72-880/2 M16 x 150(M) x M16 x 150(F) Incl. filter, specify
Disc Tip Filter Screens36-020-K10 * Pack of 10 disc tip filter 30 mesh 36-009-K10 * Pack of 10 disc tip filter 60 mesh36-005-K10 * Pack of 10 disc tip filter 100 mesh 36-003-K10 * Pack of 10 disc tip filter 200 mesh
Fluid Control
TYPE REF DESCRIPTION
Back Pressure Valve (High Pressure)78-203/34 High Pressure Back pressure valve 345 Bar MWP for hot spray
or recirculating systems.Stainless steel 3/8 BSP F inlet 2 x 3/8 BSP F outlets
Back Pressure Valves (Low Pressure)78-207/34 Low Pressure Back pressure regulating valve for circulating systems.
Stainless steel wetted section 0-10 Bar 1/2 BSP (F) inlet/outlet1/4 F gauge port
78-227/34 Low Pressure Back pressure regulating valve for larger circulatingsystems. Stainless steel wetted section 0-10 Bar 1 BSP (F) inlet/outlet1/4 BSP F gauge port
Fluid Regulators (Low Pressure)78-204/34 Low pressure fluid regulator diaphragm operated
1/4 BSP in & out fitted gauge 0-10 Bar rangeoutlet pressure (stainless wetted parts)
78-224/34 Fluid regulator higher output diaphragm controlled3/8 BSP inlet & outlet not incl. gauge. stainless steel wetted1/4 BSP(F) gauge port
78-225/34 As above but air operated. Not illustrated
Fluid Regulators (High Pressure)High pressure paint regulator providing accurate fluid pressure control.304 stainless steel wetted section. Please specify range required.
7030/1 0-69 Bar (red spring)7030/2 70-140 Bar (white spring)7030/2 110-250 Bar (gold spring)
21/0011091/101 Regulator spring 70-140 Bar21/0011093/102 Regulator spring 1-69 Bar 21/0011092/096 Regulator spring 110-250 Bar
78-01430 High pressure paint and/or mastic regulator providing accurate fluid pressure control. Made in aluminiumwith range 70-445 BAR.3/8 BSPF inlet and outlet
78-203/34
78-227/34
78-207/34
78-204/34
78-224/34
7030/x
78-214/30
Fluid Control
Pulsation Chambers16500-225 Plastic pulsation chamber with gauge, 8 Bar MWP inlet 1/2 BSP
22-001-000-00 Stainless steel wetted pulsation dampener with compressed aircontrolled diaphragm. Fluid inlet 1 BSP F. Air inlet 3/8 BSPF.suits pumps with output ref to 35 litres per minute. Complete with check valve and gauge.
22-008-000-00 Stainless steel wetted pulsation dampener with compressed aircontrolled diaphragm for larger circulating systems. Fluid inlet 11/4 BSP F. Air inlet 3/8 BSPF. Suits pumps with output upto 76 litres per minute. Complete with check valve and gauge.MWP 21bar WT35kg
22-007-000-01 Stainless steel pulsation bottle suit low or high pressure (up to 345 Bar) can accept filter. Inlet 1/2 BSP M, outlet 1/2 BSP F (Price excluding filter)
(Price with filter)
20-017-000-01 Low pressure fluid regulator for use with higher output applications 1’’ inlet and outlet. Stainless steel with easy access to lower valve assembly.
Fluid Control
32 Fax order line: 0800 195 7965
TYPE REF DESCRIPTION
Needle Valves78-200/34 1/4” needle shut off valve 2 x 1/4 BSP F inlets
Stainless steel 6000 PSI MWP
78-201/34 3/8” needle shut off valve 2 x 3/8 BSP F inletsStainless steel 6000 PSI MWP
78-202/34 1/2” needle shut off valve 2 x 1/2 BSP F inletsStainless steel 6000 PSI MWP
Ball Valves78-205/4 High pressure ball valve 400 Bar MWP
1/4 BSP F x 1/4 BSP F
78-205/34 High pressure ball valve 400 Bar MWP 1/4 BSP F x 1/4 BSP F stainless steel
78-206/4 High pressure ball valve 400 Bar MWP3/8 BSP F x 3/8 BSP F
78-218/4 High pressure 3 way L ported ball valve 400 Bar MWP3 x 3/8 BSP(F)
78-208/15 LP ball valve 1/4” F swivel nut 1/4 BSP (M). Brass nickel plated78-209/15 LP ball valve 1/4 FBE. Brass nickel plated78-215/15 LP ball valve 3/8 MBE. Brass nickel plated78-216/15 LP ball valve 3/8 FBE. Brass nickel plated
78-323/30 LP ball valve 1/4 BSP (M). Flat face x 1/4 BSP (M). Cone face,PTFE seals, stainless steel
78-324/30 LP ball valve 3/8 BSP (M). Flat face x 3/8 BSP (M). Cone face,PTFE seals, stainless steel
78-205/34
78-312/34 78-311/34
Quick Detach Fluid CouplingsQuick Detach Low Pressure Hi-Flo Fluid CouplingsFully stainless steel, easy to operate, high flow rate, stems & couplings available separatelyseal kits available
78-311/34 Fluid QD connection - new design featuring hexagon body
78-312/34 New design stem for above featuring loose nut
33Fax order line: 0800 195 7965
Fluid Control
Pump Overrun Shut Off Valve
Model B-013952
1/2 BSP ported with manual (low force) start button suitable for frequent use. ATE approved
Designed to control pumps operating in unmanned locations, such as paint mix rooms, which can suffer from failures or leakscausing rapid dissipation of paint or solvent contents from the supply drums, causing financial loss, a big clean up and firehazard. Fit an overrun valve and avoid these problems, all models feature sessitivity control as standard.
Audio and visual indicators also available by enquiry
Accessories
TYPE REF DESCRIPTION52002 Five litre black gravity bucket c/w lid. 1” BSP(F) outlet78-090/30 U pipe. Stainless steel M36(F) 1” BSP(M)78-101/30 U pipe. Stainless steel 1” BSP(F) x 1” BSP(M)
Viscosity Cups VIS-F4-K2 Pack of 2 handy plastic Ford 4 viscosity cups with metal orifice Ford 4
Gauges & Gauge Manifolds580-202 Gauge manifold M16 F x M16 M580-203 Gauge manifold 1/4 BSP F x 1/4 BSP M580-220 Riser for gauge 1/4 BSP
Dry gauges 63mm dia 580-215 Dry, 0-160psi 1/4 BSP bottom inlet, glass window. 63mm dia580-217 Dry, 0-30psi 1/4 BSP bottom inlet, polycarbonate window 63mm diameter580-218 Dry, 0-6Bar 1/4 BSP bottom inlet, polycarbonate window63mm diameter580-219 Diaphragm controlled gauge in st/steel. Glycerine filled, st/steel
case Plexiglass window, 0-160 psi 1/4 BSP bottom inlet ideal forcirculating systems.
Glycerine filled gauges 63mm dia Plexiglass, stainless body580-211 1/4 BSP bottom inlet 400Bar580-212 1/4 BSP bottom inlet 3000psi580-213 1/4 BSP bottom inlet 100psi580-214 1/4 BSP back inlet 3000psi for panel mounting c/w bracket580-216 1/4 BSP bottom inlet 2000psi580-221 1/4 BSP bottom inlet 0-30psi
Cleaning Brushes24097-R-K10 Cleaning brushes, nylon bristles (pack of 10)
580-219
580-203
580-202& 580-211
VIS-F4-K2
24097-R-K10
Accessories
Aluminiun Non Restrictor Models Low Pressure Aluminiun Restrictor ModelsTYPE REF 2 INLETS 1 OUTLET TYPE REF 2 INLETS 1 OUTLET74-911/27 1/4 BSP(M) 1/4 BSP(F) 74-711/27 1/4 BSP(M) 1/4 BSP(F)74-922/27 1/4 NPS(M) 1/4 NPS(F) 74-722/27 1/4 NPS(M) 1/4 NPS(F)74-941/27 * 1/4 BPS(M) 3/8 BSP(F) 74-741/27 * 1/4 BSP(M) 3/8 BSP(F)74-944/27 * 3/8 BSP(M) 3/8 BSP(F) 74-744/27 * 3/8 BSP(M) 3/8 BSP(F)74-952/27 1/4 NPS(M) 3/8 NPS(F) 74-752/27 1/4 NPS(M) 3/8 NPS(F)74-981/27 1/4 BSP(M) M16 x 1.5(F) 74-781/27 1/4 BSP(M) M16 x 1.5(F)74-988/27 M16 x 1.5(M) M16 x 1.5(F) 74-788/27 M16 x 1.5(M) M16 x 1.5(F)
Non Restrictor Models Stainless steel Low Pressure Stainless Restrictor Models TYPE REF 2 INLETS 1 OUTLET TYPE REF 2 INLETS 1 OUTLET74-811/30 1/4 BSP(M) 1/4 BSP(F) 74-511/30 1/4 BSP(M) 1/4 BSP(F)74-822/30 1/4 NPS(M) 1/4 NPS(F) * 74-522/30 1/4 NPS(M) 1/4 NPS(F)74-841/30 1/4 BSP(M) 3/8 BSP(F) 74-541/30 1/4 BSP(M) 3/8 BSP(F) *74-844/30 3/8 BSP(M) 3/8 BSP(F) 74-544/30 3/8 BSP(M) 3/8 BSP(F)74-852/30 1/4 NPS(M) 3/8 NPS(F) 74-552/30 1/4 NPS(M) 3/8 NPS(F)74-855/30 3/8 NPS(M) 3/8 NPS(F) 74-555/30 3/8 NPS(M) 3/8 NPS(F)74-888/30 M16 x 1.5(M) M16 x 1.5(F) * 74-588/30 M16 x 1.5(M) M16 x 1.5(F)
* Stock lines others to order
LP Y Blocks74-330 LP 2 outlet air connector Y with ball valves 1/4 BSP(F) x 2 x 1/4 BSP(M)
74-301.4 LP 3 outlet fluid Y connection, swivel nut 3/8 BSP(F)x3 x 3/8 BSP fixedincl 1 x 3/8 BSP plug
Agitators
PM60 Pneumatic agitator is perfect for preparation and mixing of most paintsin containers of 5 and 10 litre capacity. Some materials, such as lacquermay also be agitated in larger volume containers.
Standard Features• Comfortable handle• Can be hand-held/flange mounted
or on 60-100 stand• Light weight• High quality function• Stainless steel shaft & propeller• Long service life• Integral speed control & silencer
Technical Data• Air pressure for operation 0.5 to 8Bar• Speed @ 4 Bar = 900RPM• Air consumption = 100L/min• Output = 60 Watts• Weight (excluding stand) = 1.10kg• Shaft length = 440mm• Propeller diameter = 70mm
For preparation and mixing of liquid materials 200 litre (45 gallon) airdriven paint mixer mounted on stainless steel lid.
Standard Features• Comfortable T-bar handle grip• Light weight• High quality function• Long service life• Integral speed control & silencer
Standard Features• Two handles• 1.5 Hp motor• Four fixing positions around outside edge• Stainless steel lid• Stainless steel shaft• Adjustable paddle detail
A choice of rotary impellor blades areavailable60-615 55mm Ø60-614 110mm Ø
Technical Data• Operating air pressure 0.5 to 5.6Bar• Speed @ 5.6 Bar = 6,000RPM• Air consumption = 12.5CMF @ 5.6Bar• Output = 0.33kW• Weight (excluding stand) = 2.0kg• Shaft length = 500mm• Spiral paddel diameter = 80mm
60-200 flangemountingconnection alsoavailable PM60 pictured on adjustable
height stand (60-100)
80mm spiralpaddle
MRM-050Features a 0.42HP direct drive air motor for greater mixing ability eitherfor heavier materials or in larger quantities up to 25 litre capacity.
PM60 Agitator Assy
MRM 050 Agitator Assy 80mm Spiral Paddle Assy
200 Ltr agitator assy mounted on stainless steel lid assy
60-200 mounting60-100 stand
Mixing Tanks
PM60 -250The 60-250 package makes the preparation and use of sprayapplied materials simple and clean to handle whilst at the sametime helps to ensure that your material achieves and remains atthe correct specification - ready for useIt comprises a standard industrial 25 litre pail with stainless steellid, which fastens to the pail using three external fixings.The lid itself is spun and laser profiled has a filler/viewer pointwith pear shaped access plate, a 1/2BSP male connection fluidsuction tube (reaching the bottom of the pail) and a PM-60pneumatic mixer.
Exitflex now design manufacture and supply stainlesssteel mixing tanks to meet your exact specifications.Supplied with pneumatic operation mixers, filers/viewers,bottom outlet ball valve connections.
Standard Features• Light weight• High quality function• Stainless steel shaft & propeller• Long service life• Integral speed control & silencer
Technical Data• Air pressure for operation 0.5 to 8Bar• Speed @ 4 Bar = 900RPM• Air consumption = 100L/min• Output = 60 Watts• Weight (excluding stand) = 1.10kg• Standard shaft length = 440mm• Propeller diameter = 70mm
100 litre model
45 litre model
Please alow us the opportunityto quote against your mixingvessel requirements.
PM60-250 Pail mounted Agitator Assy
Pressure Feed Equipment
Exitflex are pleased to offer an extensiverange of double diaphragum pumps fortransfer duty
Please telephone wewill be pleased to offera quotation to matchyour specification.
1/3 is enough for us...You will discover the ingenious simplicity when you maintain thepump. We use approximatley 1/3 the number of parts that ourcompetitors use to build similar sized pumps.
1.Flexible installations
The connections may be rotated 180°. Simply turn theconnections to fit your piping system.Threaded BSP orNPT connections is standard. Twin connectons arealso avaiable
2.Powerful valve seats
The valve seat is under constant stress from themovement of the valve ball. To obtain best wearresistance, the integrated seat is made from AISI 316stainles steel.
3.Low air consumption
The air distribution system is designed with shortestpossible air distribution ways. This eliminates “deadspaces”, resulting in high effiencey and low airconsumption.
Typical applications
Industry Example of applications
Workshop Oil, fat, solvents, water, cooling fluid, lubricants
Print & paint Glue, additives, varnish, ink, paint, latex, acid, resins, pigments
Mining & Construction Adhesives, sump, dewatering, coal, sludge, pastes
Ceramic Industry Abrasives, glaze, water, enamels, clay
Chemistry Acids, alkalis, alcohol, solvents, latex, emulsions
With a 2.5 litre cup and a maximum working pressure of 5 Barthe EPT2.5 reduces the need for repetitive cup filling andallows the spraying of lighter viscosity materials comparedwith cup guns.
ETP2.5 Cup Assy (no hoses)ETP2.5K Cup Assy c/w 4ft hose
EPT2.5• Quick release lid clamp, saving time and reducing build up of materials• Carrying handle/hook• Suitable for conventional and HVLP applications• Lid mounted pressure release valve• Greater manoeuvrability abtained by operative compared with suction / gravity fed systems• 5 Bar (70psi) maximum working pressure• 3/8 BSP male fluid outlet connection• 1/4 BSP male air inlet connection
1
2
3
Pressure Feed Equipment
Durable construction pressurevessels supplied ready for use,with high quality valves,regulators and gauges there is achoice of manual or pneumaticmixing units.
A comprehensive stock of spare parts is available.Key components are:-
MODEL AGITATOR TYPEPTP103 10 litre lid gasket PTP118 10 litre aluminium liner PTP119 10 litre stainles steel linerPTP112 10 or 20 litre pressure gauge PTP126 10 or 20 litre pressure regulatorPTP123 20 litre lid gasket
10 litreMODEL AGITATOR TYPEETP10 None Stainless steel version availableETP10M ManualETP10A PneumaticETP10B None - bottom outlet
20 litreMODEL AGITATOR TYPEEPT20A Pneumatic Stainless steel version availableEPT20M Manual
Other sizes by enquiry
NB. All 10 litre models feature an aluminium inner lineras standard - stainless steel also available (see below).
Pre-Treatment Nozzles
Designed For Your Application
Pre-Treatment Non Corrosive CPVCPipework Systems
Pre-Treatment Nozzles
MK I Adjustable Assemblies – Standard Poly Glass Material to suit 1, 1 1/2 & 2 inch nominal Standard bore I.P.S. Pipe. Available with 14mm, 17mm and 19mm spigots to allow retrofitting 302 to most existing installations springNow available with the new Quick release tips to further reduce maintenance and down time!
Single Spring Version (for spraying pressures up to 4.0 Bar)MK1 assembly complete with Quick release V TipMK1 assembly complete with V JET tipMK1 assembly complete with HOLLOW CONE tipMK1 assembly complete with THREADED BALL tipMK1 assembly complete with FULL CONE tip
Double Spring Version (for spraying pressures greater than 4.0 Bar)MK1 assembly complete with Quick release V TipMK1 assembly complete with V JET tipMK1 assembly complete with HOLLOW CONE tipMK1 assembly complete with THREADED BALL tipMK1 assembly complete with FULL CONE tip
MK II Fixed Nozzle Holders – Standard Poly Glass Material to suit Standard 1, 1 1/2 & 2 inch nominal bore I.P.S. Pipe. Female threaded bodies 3021/8, 1/4, 3/8 & 1/2 BSP & NPT spring
Single Spring Version£2.80MKII Single spring
Double Spring VersionMKII Double spring
Replacement Tips to suit all Mkl nozzle holders in Polyglass materialReplacement Quick release Ball and V Tip Replacement Quick release V Tip onlyV jet TipHollow Cone TipThreaded Ball TipThreaded Tip Not oursFull Cone Tip Not ours
Spares for MKI & MKII assemblies in polyglass materialO ring seal (MKI & MKII) Locking Cap (MKI)Body (MKI) Body (MKII) Single spring 302SS (MKI & MKII) Double spring 302SS (MKI & MKII) Mkl assembly less tip Single ClampMkl assembly less tip & locking cap Single Clamp
Air Fed Breathing Apparatus
Exitflex are pleased to offer a comprehensive range of air fed respiratoryequipment for operators in the many working environments whereairborne contaminants continue to threaten sight, breathing and generalhealth. The system is CE marked and approved to EN270 and EN 139.This system continues to be very popular with paint sprayers, especiallythose working with two-pack paints containing isocyanates, due to thepractical, lightweight and comfortable design but most of all, theperformance of the apparatus.
• Complete kits or component parts• Choice of full visor or half mask• High capacity coalescing air filter• Belt with pre-set regulator and air purifier• Choice of optional air hoses
A choice of kits is available to suit a range ofApplication requirements.
The waist belt features an activated carbon cartridge filter to removeairborne vapours and odours, a pre-set regulator, which controls thevolume and quality of air to the visor and an air flow indicator for operatorprotection.
• Air quality to BS4275 at belt• Colour changing activated carbon cartridge• Comfortable adjustable belt• Clear flow indicator gauge• Quick replacement at low cost
The 50-612 kit (shown above left) is the most comprehensive i.e for a new installation.
These portable filtration units are especially suitedto mobile operators or to personnel who are responsible for their equipment.
The 50-515 twin filter contains a pre-filter and acoalescing filter in a convenient portable frame.
The 50-516 triple has an activated carbon filter in addition to the pre-filter and coalescing filter.
All units have a semi automatic drain with an airflow capacity up to 28cfm at 90psi.Maximum temperature. 40ºC.Maximum input 150psi.
NB Wall mounted versions are listed on page 45.
NB These filters will not remove carbon monoxide or othertoxic gases.
Air Fed Breathing Apparatus
TYPE REF DESCRIPTION
Respiratory Visors / Half Masks & Complete Outfits50-511 * Air fed visor (Acetate)50-513 * Waistbelt with filter, regulator and flow indicator gauge50-521 * Air fed half mask (excluding goggles)50-611 * Air fed outfit incl. 50-511 visor, 50-513 belt and visor covers50-621 * Air fed outfit incl. 50-521 half mask, 50-513 belt and 50-407 QD50-612 * Air fed outfit incl. 50-511 visor, 50-513 belt, 50-413-K10
visor covers, 50-406 gun hose, 50-505 10 metre supply hose &50-514 coalescer
50-612/M * Air fed outfit incl. 50-511 visor, 50-513 belt, 50-413-K10visor covers, 50-406 gun hose, 50-505 10 metre supply hose.(as 50-612 without coalescing filter)
Spare Parts and Accessories50-406 4ft gunsupply hose with 1/4 BSP Y x QD connection & 1/4 BSP(f) stem 50-411 Replacement foam seal 50-51150-412 Replacement air supply tube 50-51150-413-K10 Peel off visor covers pack of 1050-421 Replacement screen (Acetate) for 50-51150-422 Sweat band, Brow guard50-423 Flow indicator gauge for waistbelt50-428 Side wall mounting kit (mod 112)50-429 Jointing kit (mod 112)50-505 10 metre supply hose with 1/2“ male QDx QD with 1/4 BSP(F) stem50-507 Y connector
Respiratory Filters & Elements50-404 Replacement odour removal cartridge50-514 Coalescing filter (complete) 1/2” ported (mod112)50-415 Coalescing filter element for 50-51450-430 Carbon filter (complete) 1/2“ ported (mod112)50-424 Replacement carbon filter element for 50-430 & triple filter units)50-425 Replacement pre-filter element (for twin or triple filter units)50-426 Replacement pre-filter unit (for twin or triple filter units)50-515 Portable twin filter unit. Prefilter & coalescing filter (Mod 112)
mounted in portable frame.50-515/W Wall mountable twin filter unit. Prefilter & coalescing filter
(Mod 112) supplied with wall mounting kit.50-516 Portable triple filter unit. Prefilter, coalescing filter & activated
carbon filter (Mod 112) mounted in portable frame.50-516/W Wall mountable triple filter unit. Prefilter, coalescing filter,
activated carbon filter (Mod 112) supplied with wall mounting kit.
50-511
50-521
50-406 50-423
50-505
50-515
50-430 50-404 50-425 50-424
50-413-K10
50-513
50-516
Conventional Air Atomising Spray Lances
It is important to ensure a balanced air and fluid pressure “at the spray gun”.To assist in achieving this it is advisable to use a mini air regulator - or filter
regulator please see page 9.
38-002
38-220
38-210
38-230
PA131J230
Standard 12” extensionfor DeVilbiss JGA/GTi
spray gun with forward,backward & side spray360° atomiser nozzle.
EXITFLEX ‘38’ Series Airspray Gun Lances do not feature needles and thus require a different technique in use. In practice,they provide a positive affordable solution to users where a slim, lightweight extension is required for paint spray or waxapplication into difficult to reach areas inside tubes or confined spaces
The Lances are 3mm thick wall aluminium tubing as also used with the EXITFLEX airless spray extension items, this makes iteasy for you to stock for air spray or airless spray applications.
It is important to note that the atomisers detailed in this section are for use in air spray applications only, they are not suitablefor airless Some liquids may not be suitable for use with these atomisers.
It is important to use separate air and fluid control regulators. Pressure feed guns should normally feature a 1.4mm fluid tip,or a 1.8mm fluid tip. Extensions will only operate with pressure feed.
TYPE REF DESCRIPTION38-441 Fogging chamber to fit BRPHVLP gun (page 45)38-451 Fogging chamber to fit Iwata W9038-452 Fogging chamber to fit Iwata W20038-411 Fogging chamber to fit DeVilbiss, Sagola (not HVLP)38-438 Fogging chamber to fit DeVilbiss, Compact Gun38-421 Fogging chamber to fit Binks 23038-431 Fogging chamber to fit Binks BBR38-471 Fogging chamber (air assisted airless)to fit AAG-2000,
GRACO AA 2000, ALPHA PLUS & AA PLUS 74-021 Adaptor for use with Flexi, 1/2” JIC M x 1/2” JIC M38-002 Adaptor 1/2” JIC M 1/4” UNF F for use in rigid extensions38-210 Spinning atomiser, forward, backward and side spray 1/4” UNF38-220 Spinning atomiser, side spray only 1/4” UNF38-230 Fixed atomiser for use with flexi lance32-306/16 Lance 6” length rigid 32-312/16 Lance 12” length rigid32-318/16 Lance 18” length rigid32-324/16 Lance 24” length rigid32-336/16 Lance 36” length rigidA complete extension comprises 1 Fogging chamber, 1 Lance (length to suit) 1 38-002 adaptor plus/antomiser of your choice. These extensions require a pressure feed system.
Flexible Extensions -PA131J230 Flexi lance 1 metre including 38-230 fixed atomiser (excl. fogging chamber)
Flexible extensions are available using the 38-219 or 220 spinning atomiser with 1/4 bore nylon hose. Prices by enquiry
Slimline Extensions -38-500 Slimline extension tube only not including nozzle. Accepts 38-210
or 38-220 order fogging chamber extra to suit. Nickel plated finish18” long, 11mm OD
38-501 Slimline angled fixed fan atomiser complete with fogging chamber to suit and choice of 6”, 12” or 18” length. 11mm OD
Air Spray Guns
TYPE REF DESCRIPTION BRP HVLP Pressure feed.
19710 BRP HVLP Manual spray gun @ 1.0mm19712 Pressure feed @ 1.219714 Pressure feed @ 1.419715 Pressure feed @ 1.519717 Pressure feed @ 1.719719 Pressure feed @ 1.919722 Pressure feed @ 2.2
BRP HVLP Spares 202XX Needle, fluid tip & air cap kit(replace XX with Ø)1825XA Air cap (state size ie, 0.8mm - 2.2mm)18345A Seals and springs repair kit1828XA Fluid tip (state size ie 0.8mm)1625XA Fluid needle (state size ie 0.8mm)24097-R-K10 Pack 10 cleaning brushes10638A 1000cc Camlock Suction Cup
HVLP Automatic Spray Gun (Low Pressure)K99 Automatic HVLP spray gun. Stainless
steel version with recirculation base.Sizes 0.7 – 2.2mm (please specify)
Turbine Spray GunTPQ-98 HVLP turbine gun. High quality, non bleed
Air Blow Guns30100 Airblow gun with aluminium body30130 Airblow gun with booster nozzle.
Aluminium body
Cleaning GunDG-10-EK Manual cleaning gun, syphons from separate container
adjustable output 1/4 BSP air outlet
Gravity spraygunE-70 Heavy material spray gun 4mm nozzle. One litre
aluminium gravity cup. 1/4 BSP air inlet
TPQ-9830130
30100
BRP HVLPspray gunfitted withVOW type twinhose &stainless steel76 seriesreusableconnections(page 6)
K99
DG-10-EK
E-70
PROFESSIONAL
BIW-640 Tray of 8 tubs of 80 wipes
BIG INDUSTRIAL WIPES
GW30BK Textile overbraid sleeving (Polyester) 25-30mm
GW40GR Textile overbraid sleeving (Polyester) 40-60mm
PVCT 2/400 PVC sleeve 2” (50mm) approx 200m rollPVCT 3/400 PVC sleeve 3” (75mm) approx 200m roll
000000 Spray gun lubricantSuitable for lubricating spray guns, pumps etc.This is a non silicone oil for safe use with spray equipment50ml bottle with nozzle
Coveralls - pack size 50Superior non-woven cloth like fabric, soft yet strong.• Water repellent • Abrasion resistant - low lint • Elasticated wrist, ankle and hood• Reusable • Zippered front
DCL-K50 Large DCM-K50 Medium
N40-K50 Green disposable Gloves - pack size 50Latex, abrasive resistant gloves, offering protection for the hands, suitable for use with paints and inks.Not suitable for continuous immersion in aggressive solvents.
Universal visor coversto suit square or round edge visors
UVC-K10 Pack 10UVC-K50 Pack 50
General Consumables
®
Airless
Spray painting has evolved changing tip sizes - with a twist
ONE TIPTWO ANGLES!
Air Assisted Airless
Save Time • Paint • Energy • Money
Top Quality -Best Results
®
POPULAR SIZES
Orifice size Wide angles/narrow angleseg.40/20º etc.
Ins mm 40º 50º 60º0.010´´ 0.25 40/20º 50º/20º 60º/30º0.012´´ 0.30 40º/20º 50º/20º 60º/30º0.014´´ 0.35 40º/20º 50º/20º 60º/30º0.016´´ 0.40 40º/20º 50º/20º 60º/30º0.018´´ 0.45 40º/20º 50º/20º 60º/30º0.020´´ 0.50 40º/20º 50º/20º 60º/30º
WIDE SPRAY PATTERN CHOICE30º to 80º subject to orifice size.Orifice range 0.004 - 0.026 Othersizes by enquiry.
NARROW SPRAY PATTERNCHOICE10º to 30º subject to orifice sizewhich must be the same on wideand narrow angles.
AIRLESS TWINTIPS
Type Tip only Tip and seal kit
Speedy Mk II 88-013/0 -Speedy Mk III 88-303/0 88-393/0Speedy Mk IV 88-403/0 88-493/0Speedy Mk V 88-503/0 88-593/0
For Airless and Air Assisted Airlessspray guns
Important a minimum 20º differential must be maintained between wide and narrow angles.Stock range as highlighted in Red. Further sizes available to order.
AIRLESS LINE-MARKING TWINTIPS (TLM)
Type Tip only
Speedy Mk III 88-310/0Speedy Mk IV 88-410/0Speedy Mk V 88-510/0
AIR ASSISTED AIRLESS TWINTIPS
Type Tip only Tip and seal kit
TRI-A 83-023/0 83-022/0
Top Quality -Best Results
Mk V Mk IV TRI-A
To order:Specify tip reference No. followed by wide angle, orifice ininches & narrow angle.eg: Speedy V, 88-503/0 518/20 or TRI-A, 83-023/0 412/20.
Airless Spray Tips & Accessories
63-505/30
63-509/35
Drain cleaning nozzles
TYPE REF DESCRIPTION
Titan Variable Spray Tips341-0XX Titan Variable Tip All sizes, 15, 20, 24, 28, 41, 49 *341-3XX Spare needle for Titan Tip All sizes36-052/0 Tip Guard for Titan variable tip Fits Graco36-053/0 Tip Guard for Titan variable tip Fits DeVilbiss36-054/0 Tip Guard for Titan variable tip Fits Binks36-057/0 Tip Guard for Titan variable tip Fits Wagner
Tip Cleaning Needles36-701/00 (Silver) (Box 12x12) 08/110gm for tips up to .011 th orifice36-703/00 (Purple) (Box 12x12) 10/110gm for tips over .011 th orifice
Pre-Orifice Discs Colour Code
63-004/0 Pre Orifice 0.016” Yellow63-005/0 Pre Orifice 0.019” Red63-007/0 Pre Orifice 0.026” Blue63-010/0 Pre Orifice 0.039” Black63-070/0 Mix air Pre Orifice
All airless and air assist tips listed below are genuine ExitFlex products
Airless Spray TipsNote : This section covers standard airless tips.Reversible systems are featured on following pages
63-505/30 Flat tip Industrial Grade Stainless body *63-509/35 Flat Tip Superfine Finishing *63-507/4 Line Marking Tip Flat tip type body *63-510/0 Insert Tip ** (Blastaway™)63-515/0 Insert Tip ** (Turnaflo™ )
** Special order only - minimum 10 per size
TN-SSTC-XX Round spray Hollow cone spray, tungsten31-HAF-0180Round spray 80° full cone spray S.S 0.5mm orifice
3.95L Hour @ 3Bar (not illustrated)
Drain Cleaning Nozzles63-310/30 303 Stainless steel static pipe cleaning nozzle (3 x 1mm rear jets)63-317/30 303 Stainless steel static pipe cleaning nozzle (3 x 1mm rear +1 x
0.7mm front jet)63-562/18 Nylon seal for 63-310/30, 63-317/30,63-410/0 & 63-412/063-410/0 Rotary pipe cleaning nozzle (4 x 1mm jets)
Insert tips
TN-SSTC-XX
Tip Chart
ORIFICE SIZE SPRAY ANGLES IN DEGREES AND INCHES FLOW RATE100Bar (1500psi)
10 20 30 40 50 60 70 80 90 100 110 L/min GPMinch mm 2/3 4/6 6/8 8/10 10/12 12/14 14/16 16/18 18/20 20/22 22/24
0.007 0.18 0.18 0.047
0.009 0.23 0.25 0.066
0.011 0.28 0.37 0.087
0.013 0.33 0.57 0.15
0.015 0.38 0.72 0.19
0.017 0.43 0.98 0.26
0.019 0.48 1.30 0.34
0.021 0.53 1.52 0.40
0.23 0.58 1.83 0.48
0.025 0.63 2.13 0.56
0.027 0.68 2.50 0.66
0.029 0.73 2.95 0.78
0.31 0.78 3.42 0.90
0.033 0.84 3.80 1.00
0.035 0.89 4.30 1.14
0.037 0.94 5.10 1.34
0.039 0.99 5.50 1.45
0.041 1.04 6.15 1.62
0.043 1.09 6.80 1.79
0.045 1.14 7.40 1.95
0.047 1.19 7.94 2.09
0.049 1.24 8.50 2.25
0.051 1.29 9.10 2.40
0.053 1.35 9.80 2.60
0.055 1.40 11.00 2.90
0.057 1.45 11.80 3.10
0.059 1.50 12.50 3.30
0.061 1.55 13.70 3.60
inch mm 10 20 30 40 50 60 70 80 90 100 110 L/min GPM2/3 4/6 6/8 8/10 10/12 12/14 14/16 16/18 18/20 20/22 22/24
SPRAY ANGLES IN DEGREES AND INCHES
= Standard tip spray angle for the given orifice size = Speedy tip spray angle for the given orifice size
Spray angles quoted are correct but spray width depends upon viscosity, solids and pressure.Figures quoted as a guide only.
Note Other sizes may be possible by special enquiry. Please enquire.
This chart relates to all standard range of tipsEach EXITFLEX tip is carefully manufactured and individually tested for assured quality, performance and life,under demanding conditions.Sizes for Superfine tips can be found on page 9 of this brochure. They are not covered by this char t.
Standard range Speedy range
Air Assisted Airless Spray Tips, Seals & Caps
63-552/30 Mixair Tip AK (Kremlin pattern) groove type *
63-550/11 Mixair Tip AK (Kremlin pattern) pin type *
36-610-K10 Micro Tip Filter 100 mesh for AK tips (pack 10) *
36-618-K10 Micro Tip Filter 100 mesh for flat tips c/w 21-008 seal (pack 10) *
63-555/11 Mixair Tip AL (Larius pattern) Pin type *
63-555/30 Mixair tip AL (Larius pattern) Groove type *
63-560/15 Mixair Tip AG (Graco pattern) GGW fits HS200 *
63-611 Mixair Tip AG (Graco pattern) GG4 fits Alpha 5 *
63-562/19 Seal AG tip *
63-565/30 Mixair Tip AB (Binks pattern) Vantage™ *
63-570/11 Mixair Tip AS (Sagola pattern) Speeflo™ *
63-554/18 O Ring PTFE 3.5 x 2 AK, AL
63-573/18 O Ring PTFE seal AS tips
63-580/19 Mixair Tip RE Black plastic (Excl seal) *
163-582 Seal RE Pattern Tip Black plastic
63-597/020 Mixair Tip AW (Wagner B pattern) Black plastic *
63-577/30 Mixair Tip AO (Opco Böllhoff Pattern) 15mm *
63-598/30 Mixair Tip AD (DeVilbiss Optima™wiwa) 9.5mm *
83-015 TRI-A™ Ball tip TRI-A™
63-610/30 Mixair tip DT (Dete Krautzberger pattern) *
Please refer to Page 49 for full TRI-A reversible air assisted airless system details & discounts
Air CapsEBX-3 Air Cap For AK pin type Mixair tips *EBX-8 Air Cap For AK pin type Mixair tips *
Blast-A-Way Pony
POSITION TYPE REF DESCRIPTION- 21-102/0 Blastaway Pony Fits Graco- 21-103/0 Blastaway Pony Fits DeVilbiss- 21-104/0 Blastaway Pony Fits Binks- 21-105/0 Blastaway Pony Fits Atlas Copco- 21-116 Blastaway Pony Fits Iwata- 21-107/0 Blastaway Pony Fits Wagner, Aro1 21-001/2 Nut2 21-002/32 Housing (st st)4 21-004/7 Ball5 21-005/23 Seal6 21-006/18 ‘O’ Ring PTFE (old number 201-026)8 21-008/46 Seal9 21-009/26 Handle10 21-010/6 Screw and Washer11 21-011/41 Seal12 21-012/30 Spacer13 21-013/30 Screw14 21-014/11 Seat (brass)- 21-015/0 Repair Kit
16 21-016/41 Guard (Black)- 21-033 Screw (Delavan)7 21-202/2 Adaptor Fits Graco7 21-203/2 Adaptor Fits DeVilbiss7 21-204/2 Adaptor Fits Binks7 21-205/2 Adaptor Fits Atlas Copco7 21-207/2 Adaptor Fits Wagner, Wiwa, Aro
Blast-A-Way MKII Speedy
BASE UNITS88-262 Base unit fits 7/8 x 1488-243 Base unit fits 3/8 NPS88-264 Base unit fits 3/4 x 2088-265 Base unit fits M18 x 188-266 Base unit fits M18 x 1.588-247 Base unit fits 11/16 x 16
*SPRAY TIPS88-010 Standard tip 88-020 SF Superfine tip83-013 Twin Tip
SPARE PARTS88-061 Safety guard 88-052 Adaptor88-054 Adaptor88-055 Adaptor88-526 Adaptor88-057 Adaptor88-060 Housing stainless88-063 Swivel seal assembly88-023 Pre-adaptor 3/8 NPS F – 7/8 x 14 M88-027 Pre-adaptor 11/16x16 F – 7/8 x 14 M21-008 Gasket
Blast-A-Way MKIII Speedy
BASE UNITS88-552 Base unit fits 7/8 x 1488-553 Base unit fits 3/8 NPS88-554 Base unit fits æ x 2088-555 Base unit fits M18 x 188-556 Base unit fits M18 x 1.588-557 Base unit fits 11/16 x 16
*SPRAY TIPS88-391 Standard ball tip and seal88-392 SF Superfine ball tip and seal88-390 Linemarking tip and seal88-303 Twin tip
SPARE PARTS88-506 Safety guard No 2 and 388-536 Safety guard Nos 4, 5, 6, 788-512 Adaptor88-544 Adaptor88-545 Adaptor88-526 Adaptor88-547 Adaptor88-504 Housing stainless steel No 2 and 388-534 Housing stainless steel No 4, 5, 6,788-505 Seal and gasket kit88-523 Pre-adaptor 3/8 NPS F – 7/8 x 14 M88-527 Pre-adaptor 11/16x16 F – 7/8 x 14 M21-008 Gasket
IMPORTANT NOTESpeedy III tip and seal kits are interchangeable into GRACO RAQ IV systems. The tip cylinders must be fitted with
the matching seal supplied.
Blast-A-Way MKIV Speedy
BASE UNITS SPARE PARTS88-452 Base unit fits 7/8 x 14 88-506 Safety guard No 2 and 388-453 Base unit fits 3/8 NPS 88-536 Safety guard Nos 4, 5, 6, 788-454 Base unit fits æ x 20 88-512 Adaptor88-455 Base unit fits M18 x 1 88-544 Adaptor88-456 Base unit fits M18 x 1.5 88-545 Adaptor88-457 Base unit fits 11/16 x 16 88-526 Adaptor
88-547 Adaptor*SPRAY TIPS & TIP & SEAL KITS 88-404 Housing stainless steel No 2 and 388-401 Standard tip cylinder 88-434 Housing stainless steel No 4, 5, 6,788-491 Standard tip & seal kit 88-463 Seal kit88-402 SF Superfine tip cylinder 88-523 Pre-adaptor 3/8 NPS F – 7/8 x 14 M88-492 SF Superfine tip & seal kit 88-527 Pre-adaptor 11/16x16 F – 7/8 x 14 M88-490 L M Linemarking tip cylinder 21-008 Gasket88-403 Twin tip
IMPORTANT NOTESpeedy IV tip and seal kits are interchangeable into ASM, WAGNER & GRACO RAQ systems.
The tip cylinders must be fitted with the matching seal supplied.
Blast-A-Way MKV Speedy
BASE UNITS88-552 Base unit fits 7/8 x 1488-553 Base unit fits 3/8 NPS88-554 Base unit fits æ x 2088-555 Base unit fits M18 x 188-556 Base unit fits M18 x 1.588-557 Base unit fits 11/16 x 16
*SPRAY TIPS88-591 Standard ball tip cylinder kit88-592 SF Superfine ball tip cylinder kit88-590 L M Linemarking tip cylinder kit88-503 Twin tip
SPARE PARTS88-506 Safety guard No 2 and 388-536 Safety guard Nos 4, 5, 6, 788-512 Adaptor88-544 Adaptor88-545 Adaptor88-526 Adaptor88-547 Adaptor88-504 Housing stainless steel No 2 and 388-534 Housing stainless steel No 4, 5, 6, 788-509 Seal kit88-523 Pre-adaptor 3/8 NPS F – 7/8 x 14 M88-527 Pre-adaptor 11/16x16 F – 7/8 x 14 M21-008 Gasket
IMPORTANT NOTESpeedy V tip and seal kits are interchangeable into ASM, WAGNER & GRACO RAQ & GHD systems.
The tip cylinders must be fitted with the matching seal supplied.
Airless Spray Lances
Directional filter housing &Speedy MkV (page 54)
NO. TYPE REF DESCRIPTION1 32-050/2 Universal connector2 36-202/43 Nut 7/8 - 14 UNF Graco2 36-203/30 Nut 3/8 - 18 NPS DeVilbiss, Kremlin2 36-204/30 Nut 3/4 - 20 UNF Binks2 36-205/30 M 18 x 1 Atlas Copco2 36-207/43 Nut 11/16 - 16 UNEF Wagner, Aro3 32-002/17 Directional w/filter housing 7/8 UNF3 32-007/17 Directional w/filter housing 11/16 UNF4 32-102/17 Straight filter housing 7/8 UNF4 32-107/17 Straight filter housing 11/16 UNF5 36-020-K10 Disc filter 30 mesh. Pack of 105 36-009-K10 Disc filter 60 mesh. Pack of 105 36-005-K10 Disc filter 100 mesh.Pack of 105 36-003-K10 Disc filter 200 mesh Pack of 106 32-132/27 Straight adaptor 7/8 UNF6 32-137/27 Straight adaptor 11/16 UNF7 21-008/46 Seal8 32-306/16 Lance 6 inches9 32-312/16 Lance 12 inches10 32-318/16 Lance 18 inches11 32-324/16 Lance 24 inches12 32-336/16 Lance 36 inches13 38-004 Nylon plug seal (use in place of filter for speedy MKV)
12” extrension on SP90airless gun (page 40) withdirectional filter housing &Speedy MkV (page 39).
Airless Spray Lances
880-355 Flow Gun
PG-300 Pole Gun 3000mmPG-240 Pole Gun 2400mmPG-180 * Pole Gun 1800mmPG-150 * Pole Gun 1500mmPG-130 Pole Gun 1300mmPG-090 Pole Gun 900mmPG-050 Pole Gun 500mm
* Stock, others to order
Airless Flow Gun - model 880-355 suitable for application of grease, sealers and variousproducts of high viscosity. Normaly used with extrusion pumps up to 350 Bar MWP. Triggerguard fitted as standard.
Airless Pole Guns - suitable for many kinds of paint products. Triggerguard included. Needle extended up to an adjustable position housing,11/16”UNF connection to accept 88-457 Mk IV tip housing.
✔ 350 Bar (5,000 psi) max inlet pressure
✔ fluid inlet connection 1/4 NSP(M)
✔ weight: 500 grams
✔ 210 Bar (3,000 psi) max inlet pressure
✔ fluid inlet connection 1/4 NPS(M)
Flow Gun
Pole Guns
SP90 Manual Airless Spray Gun
SP90 illustrated with 88-557 SpeedyMkV (rated 517 Bar) - see page 54
✔ 500 Bar MWP
✔ 4 finger trigger
✔ gun handle filter (included)
✔ CE marked
✔ swivel fluid inlet
✔ choice of 1/4 NPS / 1/4 BSPor M16 fluid inlet connection
SP 90 ModelsTYPE REF DESCRIPTION90-500/00 SP90 manual spray gun 500 Bar rated. 1/4 NPSM male fluid connection inc speedy + tip 11/16 x 1690-501/00 SP90 manual spray gun 500 Bar rated. M16x1.5 male fluid connection inc speedy + tip 11/16 x 1690-502/00 SP90 manual spray gun 500 Bar rated. 1/4 BSP male fluid connection inc speedy + tip 11/16 x 1690-530 SP90 manual spray gun 500 Bar rated. 1/4 NPSM male fluid connection inc speedy + tip 7/8 x 14
Spare parts for SP90 spray gunsPOS. REF DESCRIPTION POS. REF DESCRIPTION1 90-401 Guard and nut assembly 14 90-414 Handle gasket4 90-404/2 Fluid tip diffuser 7/8 x 14 15 90-415 Handle4 90-404/7 Fluid tip diffuser 11/16 x 16 17 90-417 Filter spring5 90-405 Guard 18 90-418 Gasket6 90-406 Needle 19 90-419 Swivel 1/4 NPS7 90-407 Needle packing seal 20 90-420 Swivel M16 x 1.58 90-408 Pressure washer 21 90-421 Swivel 1/4 BSP9 90-409 Needle packing screw 22 90-422 Trigger assembly10 90-410 Cylinder 23 90-423 Trigger lock assembly11 90-411 Locking nut 24 90-424 Trigger pin and nut12 90-412 Gun spring 90-430 Needle repair kit (90-406/408/409/411)13 90-413 Spring cap 90-300 Repair kit
SP91 Manual Lightweight Airless Spray Gun
SP91 illustrated with Speedy MkIV(rated 400 Bar) - see page 53
✔ 350 Bar MWP
✔ 2 finger trigger
✔ ultra lightweight (425g)
✔ CE marked
✔ swivel fluid inlet
✔ trigger guard
✔ 1/4 BSP fluid inlet connection
SP91 ModelsTYPE REF DESCRIPTION91-700 SP91 manual spray gun 350 Bar rated. 1/4 BSP male fluid connection inc speedy + tip
Spare parts for SP91 spray gunsPOS. REF DESCRIPTION POS. REF DESCRIPTION3 91-703 Trigger guard 15 91-715 Pusher pin (x2)5 91-705 Fluid tip diffuser 16 91-716 U packing5-1 91-705-1 O ring 17 91-717 Swivel connection 1/4 BSP6 91-706 Needle 18 91-718 Trigger pin7 91-707 End cap 19 91-719 Hex. Cap nut (x2)8 91-708 Pusher 20 91-720 Set screw10 91-710 Packing retainer 21 91-721 O ring11 91-711 Packing case 22 91-722 Back up ring T213 91-713 Trigger assembly 23 91-723 Spanner14 91-714 Spring
Diffuser thread M18 x 1.5 accepts 88.-556 speedy V or 88-456 speedy IV
✔ 250 Bar MWP
✔ CE marked
AP81 ModelsTYPE REF DESCRIPTION81-500 AP81 automatic airless spray gun 250 Bar rated. Single 1/4 NPS male fluid connection incl speedy and tip81-510 AP81 gun only (excl tip and base)
Spare Parts for AP81 spray gunsPOS. REF DESCRIPTION POS. REF DESCRIPTION
1 81-401 Guard and nut 9 81-414 ‘O’ ring3 81-404 Fluid tip diffuser 10 81-415 Lip seal4 81-405 Needle 11 81-416 Piston18 81-406 Gasket 12 81-417 ‘O’ ring17 81-407 Nipple 13 81-418 Lip seal19 81-408 Locking screw 14 81-419 Lock nut20 81-409 Push in fitting 15 81-420 Gun spring6 81-411 Pressure washer 16 81-421 Cylinder screw cap7 81-412 Needle packing seal 21 81421/A Ring8 81-413 Packing screw
Diffuser thread 11/16 unf - accepts 88-557 speedy V or 88-457 speedy IV
AP81 Automatic Airless Spray Gun
81-500 illustrated with 88-457 Speedy MkIV - see page 38
The AP81 automatic airless spraygun is designed for continuous useon automatic stations with highpressure airless spraying pumpsand feature a diffuser tip, pneumaticoperation, a flat tip guard asstandard.
AP20 Automatic Airless Spray Gun
✔ compact design (107 x 39 x 65mm) ✔ 316 stainless steel (wetted)
✔ 345 Bar MWP (5,000psi) ✔ 1/4 BSP(F) fluid inlets
The AP-20 automatic airlessspray gun is made from 316stainless steel, wetted.Designed for continuous use onautomatic stations up to 345Bar MWP
AP-20 Stainless steelautomatic airless spray gunillustrated with standard flat tip(not included)
AP20 ModelsTYPE REF DESCRIPTION20-500 AP-20 automatic airless spray gun 345 Bar rated. Single 1/4 NPS male fluid connection20-550 AP-20 automatic airless spray gun 345 Bar rated. 2 x 1/4 NPS male fluid connections for recirculation
Spare parts for AP20 spray gunsPOS. REF DESCRIPTION POS. REF DESCRIPTION1 92-001 Nozzle 63-505 9 92-009 Packing screw2 21-008 Nozzle Packing 10 92-010 Needle assembly3 92-003 Seat 11 92-011 Piston disc4 92-004 Nozzle nut 12 92-012 Nut M55 92-005 Gun body 13 92-013 Spring6 92-006 Washer 14 92-014 O ring7 92-007 Oil seal 15 92-015 Needle packing set8 92-008 Cap nut 16 92-016 Air sealDiffuser thread M18 x 1 accepts 88-555 speedy V or 88-455 speedy IV
AAG-2000 Manual Air Assisted Airless Spray Gun
AAG-2000 illustratedwith TRI-A system
✔ 240 Bar MWP
✔ accepts TRI-A reversible kit
✔ 2 finger trigger
✔ fluid inlet filter included
✔ CE marked
✔ 1/4 BSP air & fluid connection
AAG-2000 ModelsTYPE REF DESCRIPTION
AAG-2000 AAG-2000 manual air assisted airless spray gun 240 Bar MWP 1/4 BSP maleair & fluid connection, complete with disc tip housing & screen (excl spray tip)
supplied with standard air cap - order TRI-A separately if required.Spare parts for AAG-2000 spray gunsTYPE REF DESCRIPTION TYPE REF DESCRIPTION96-401 Air cap retaining ring96-401A Air cap retaining ring TRI-A96-402 Air cap (standard)63-560/15 “AG” mixair tip (state size)63-562 Tip gasket96-404 O ring96-405 Air diffuser96-406 Needle seat96-406/2000 Needle seat96-407/2000 Needle96-410/2000 Bush96-411/2000 Valve shaft96-412 Nut (x2)96-413 Washer (x2)96-414 Trigger pin
96-418 Fan regulator96-419 Valve cap96-420 Spring96-421 Air valve96-422 Packing nut96-423 Valve packing96-424 Fluid gasket96-425 Fluid connector96-426 Fluid tube 36-XXX-K10 Disc tip filter (Pack 10)
(See page 19 for choice of screens)96-428 Trigger96-429 Air inlet connection96-430 Disc tip filter housing
TRI-A Air Assisted Airless Spray Gun
✔ reversible AAA
✔ 140 Bar MWP
✔ 2 finger trigger
✔ CE marked
✔ disc tip filter built into fluid tube
✔ 1/4 BSP fluid inlet connection
✔ 1/4 BSP air inlet connection
✔ manual & automatic guns
Spare parts for TRI-A manual spray guns (83-001)TYPE REF DESCRIPTION TYPE REF DESCRIPTION83-401 Aircap retaining ring 83-417 Air valve plug83-402 Friction ring (PTFE) 83-418 Air valve spring83-010 TRI-A air cap base 83-419 Air valve packing83-011 TRI-A swiveling seal assembly 83-420 Air valve opening bar83-012/23 K10 Nylon gasket for 83-011 (pk10) 83-421 O ring (green viton)83-013 TRI-A ball tip & seal kit(state size) 83-422 Air valve body83-015 TRI-A ball tip (state size) 83-433 Air/needle valve needle packing83-403 Air cap separation gasket. 83-434 Flat washer 3x7x0.5 zinc plated83-405 Body / nozzle holder 83-435 Air valve packing spring83-406 PTFE packing 83-436 Air valve packing nut83-407 Needle packing set (complete) 83-437 Trigger lock lever and screw83-408 Packing nut 83-439 Air inlet connection 1/4 BSP male83-409 Head cone gasket 83-440 Air control valve (complete)83-410 Trigger pin screw 83-441 Trigger83-411 Fluid needle (complete) 83-442 Filter housing (without filter)83-412 Fan control adjuster (complete) 36-005-K10 Disc tip filter (pack 10) See page 3183-413 O ring (green viton) 83-443 Fluid inlet connection 1/4 NPS83-414 Fluid needle spring 83-444-K10 Nylon cleaning brush (pack 10)83-415 Base for fluid needle spring 83-445 Seals & springs kit (pos.2,6,9,12,23,83-416 Fluid control adjusting valve 25,29,30,32,34,35,36)
183-510 Dismantling wrench
83-001 TRI-A illustrated withreversible aircap & tip
For TRI-A Aircaps and Tips, see pages 67.
TRI-A Spray Gun ModelsTYPE REF DESCRIPTION83-001 MANUAL TRI-A AIR ASSISTED AIRLESS SPRAY GUN 140 Bar MWP (2000psi). Two
air chambers, MWP 140 Bar. 1/4 BSP air & fluid inlets. Colour blue.(excludes air cap & tip)
TRI-A Auto
✔ 140 Bar MWP (2000psi)
✔ accepts TRI-A reversible kit
✔ 1/4 BSP fluid connection
✔ CE marked
Pos. Ref Description 3 83-603 Head4 83-604 Needle Packing Kit5 83-605 Air Valve Kit6 83-606 Body7 83-607 Fluid Inlet Connection Body10 83-610 Air Inlet Base Control11 83-611 Air Piston Assembly12 83-612 Piston Spring13 83-613 Cylinder Cap14 83-614 Needle Spring15 83-615 Needle Adjuster Assembly
Pos. Ref Description 22 83-403 Air Cap Separation Gasket
83-000 Repair KitComprising:
3 x ‘O’ Rings ref 3b)1 x ‘O’ Ring (ref 11a)1 x ‘O’ Ring (ref 11b)1 x Piston Spring (83-612)1 x Needle Spring (83-614)6 x ‘O’ Rings (ref 10a)1 x Air Cap Separation Gasket (83-403)
TRI-A Spray Gun ModelsTYPE REF DESCRIPTION
83-600 AUTOMATIC TRI-A AIR ASSISTED AIRLESS SPRAY GUN 140 Bar MWP(2000psi). Includes a mounting base with air and fluid fittings and connections.Compact and durable. Teflon packings and stainless steel fluid passages.Accepts TRI-A 83-005 reversible nozzle system (not included as standard)
The TRI-A air assisted airless spray gun in association with the TRI-A reversable spray tip system is suitable for use in demanding industrial applications.The features of the gun and air cap/nozzle combination provide many benefits to the user; reduced down-time due to reversible cleaning nozzles and ease of servicing,compact, durable anodised body, superb atomisation and fan control. TwinTips also available giving 2 angles back-to-back from 1 tip key.
TYPE REF DESCRIPTION83-010 TRI-A AIR CAP BASE
For both standard and SF
83-011 TRI-A SWIVEL SEAL ASSEMBLYFor both standard and SF
83-015 TRI-A STANDARD SPRAY TIP KEY
83-020 TRI-A SF SPRAY TIP KEY
83-023 TRI-A TWIN TIP KEY
TRI-A Adaptor kits
The following adaptor kits allow the TRI-A reversible tip assembly to be fitted to various manufacturer’s spray guns.TYPE REF DESCRIPTION83-105/0 SEAL FOR KREMLIN GUN
This seal enables the fitting of a reversible TRI-A to the standard KREMLIN MX range.
83-009/14 ADAPTOR RING FOR AAG-2000 GUN & GRACO GUNThis adaptor ring allows the reversible TRI-A to be fitted directly onto the Exitflex AAG-2000 & GRACO ALPHA PLUS spray guns.
83-525/0 TRI-A KIT ASSY FOR GRACO ALPHA GUNS
83-509/30 PRE-ADAPTOR HEAD FOR B.F OPTIMA GUNPre-adaptor head complete with seals, ring and spannerThis kit comprises all components required to upgrade a standard Optima spray gun to accept the TRI-A reversible head
83-025/0 TRI-A TWIN TIP KIT TO FIT KREMLIN AND SEIWA SPRAY GUNSComprises Aircap and Tip Seal
Suction & Pressure Hose Assemblies
2 Metres
1/ This represents the styles of assemblies available.Refer to chart opposite for range detail and prices.2/ Spring guards are available as extras if required.
Suction & Pressure Hose Assemblies
ASSEMBLY HOSE HOSE HOSE CONNECTIONSPART NO BORE TYPE
37-100/1/1800 ✔ SR 1.16 2
37-101/1/2000 ✔ “ 2
37-102/1/2000 ✔ “ 1 1
37-103/1/2000 ✔ “ 1 1
37-104/1/2000 ✔ “ 1 1
37-105/1/2000 ✔ “ 1 1
37-106/1/2000 ✔ “ 1 1
37-107/1/2000 ✔ “ 1 1
37-108/1/2000 ✔ “ 1 1
37-109/1/2000 ✔ “ 1 1
37-110/1/1800 ✔ SR 1.12 2
37-111/1/2000 ✔ “ 2
37-112/1/2000 ✔ “ 1 1
37-113/1/2000 ✔ “ 1
37-114/1/2000 ✔ “ 1 1
37-115/1/2000 ✔ “ 1
37-116/1/2000 ✔ “ 1 1
37-117/1/2000 ✔ “
37-118/1/2000 ✔ “ 1 1
37-119/1/2000 ✔ “ 1 1
37-120/1/2000 ✔ TC 1.8 2
37-121/1/2000 ✔ “ 2
37-122/1/2000 ✔ “ 1 1
37-123/1/2000 ✔ “ 1 1
37-124/1/2000 ✔ “ 1 1
37-130/1/2000 ✔ LPV 1.8 2
37-131/1/2000 ✔ “ 2
37-132/1/2000 ✔ “ 1 1
37-133/1/2000 ✔ “ 1 1
37-134/1/2000 ✔ “ 1 1
Notes1. To order alternative lengths alter the last 4 digits of the part number to the mm length required.
IE, For 1 metre 37-100/1/2000 becomes 37-100/1/1000.Add or subtract price per metre by the required length variation for each hose type. Price per 1/2 metre.
2. If stainless steel fittings are required amend the centre digit /1/ to /30/ but check availability.Carbon steel fittings are generally ex- stock where stainless steel fittings may be on a longer lead-time.
3. Spring guards are available as extras if required. Specify when ordering.4. All ferrules mild steel plated except on TC/30/ assemblies.
2 METREASSEMBLIES
1/2” 3/4” 1”
1/2”
BS
PT
(M)
1/2”
BS
P(F
)
1/2”
BS
P(F
)90
1”B
SP
T(M
)
1”B
SP
(F)
1”B
SP
(M)
1”B
SP
(F)9
0
M36
X2(
F)
M36
X2(
F)9
0
3/4”
NP
T(M
)
3/4”
NP
SM
(F)
3/4”
BS
P(F
)90
3/4”
BS
PT
(M)
3/4”
BS
P(F
)
Suction Systems 25 Litre
37-530 Straight inlet to pump, 3/4 BSP Female connection.Black rubber suction hose, 19mm bore Stainless steel wand, carbon steel connection.Suitable for 25 Litre container.Design to accept 36-453 filter (including screen to choice) order extra.
37-531 90° inlet pump. Specification otherwise the same as 37-530
37-001/30Stainless steel 25mm diasuitable for use with largerpumps and heavy materials.Equipped to accept filter assembly 36-450
37-002/30As 37-001/30 butwith fluted endwhere no filter is required.
37-004/30Stainless steel16mm Dia.Suitable for lightmaterials, smallpump or returnhoses.No filter option
37-005/30Stainless steel19mm Dia.Traditional 90°bend, equipped to accept filter assembly 36-453
37-003/30Stainless steel 19mm Dia.straight for use with smaller pumps.Equipped to acceptfilter assembly 36-453
Suction Systems 205 Litre
37-540 Straight inlet to pump, 3/4 BSP Female connection.Black rubber suction hose, 19mm bore Stainless steel wand carbon steel connection.Suitable for 205 litre container Designed to accept 36-453filter (including screen to choice) order extra.
37-541 90° inlet to pump, specification otherwise the same as 37-540IN16 Model
37-006/30 Stainless steel 19mm Dia 90°bend 1/2 BSP Male, coned forhose and equipped to accept 36-453 filter assembly (including screen to choice)Order extra
37-016/30Stainless steel 19mm Dia 90°bend 3/4 BSP Male coned forhose and equipped to accept 36-452 filter assembly (including screen to choice)Order extra
37-026/30Stainless steel 25mm Dia 90°bend 1" BSP Male coned forhose and equipped to accept 36-450 filter assembly (including screen to choice)Order extra
37-007/30Stainless steel 25mm Dia to suit largercontainers up to 205 litre. Adjustable height with locking collar.1" BSP Male connections2" BSP container thread.Equipped to accept 36-450 filter assembly (including screen tochoice) Order extra.
Suction Wand Bung Mounting Suction Wand 205 Litre
Suction Systems
Electronic Diaphragm OutfitsWagner / Larius Pattern
37-520Straight inlet to pump Enamel type, carbon steel tubes 1/2" bore suction hose
37-521Suction tube assembly
37-502Return tube assembly
37-525System with 36-455filter including screen
37-51090 inlet to pump Latex type, carbon steel tubes1" bore suction hose
37-511Suction tube assembly
37-512Return tube assembly
37-515System with 36-454 filter including screen to choice
37-500Straight inlet pump Latex type, carbon steeltubes 1" bore suction hose
37-501Suction tube assembly
37-502Return tube assembly
37-505System with 36-454filter including screen to choice
Modular Colour Change System 250 Bar MWP
Need to colour change with Airless or Air Assisted Airless Systems?
Yes - The solution is the MODULAR COLOUR CHANGE SYSTEM
Available to suit thenumber of colours yourequire.
All systems in stainlesssteel with easy to service colour valve
Pneumatic controlsystems not included but can be quoted upon request
Fast easy colourchanging, saves time,keeps equipmentcleaner & uses lesssolvent
✔ easy to maintain and service
✔ low cost maintenance
✔ very few parts required
✔ use with Manual and Automatic Spray Systems
✔ fully stainless steel - suitable for water based materials
✔ fast efficient valve action
✔ modular design - easy to add to at a later stage
Illustrated: Colour Change Valve & Section of Manifold
Modular Colour Change System 250 Bar MWP
The system comprises a modular manifold in stainless steel arranged vertically to accept colour changevalves mounted horizontally.Alternative manifold arrangements are also available including single piece up to 8 valves and a radialto accept 6 valves.Each colour change valve is opened and closed pneumatically (The pneumatic control system is notincluded, as many prefer to supply this themselves. We can quote upon request)
The colour or fluid enters from the supply at the CCV inlet, passes through the modular manifold andexits at the base of the manifold column.
When calculating a system price remember to include 1 valve for solvent in addition to the number ofvalves corresponding to the number of colours. e.g. a 4-colour system as an example will feature 5valves.
NO. OF COLOURS SOLVENT FLUSH VALVE TOTAL VALVES2 1 33 1 44 1 55 1 66 1 77 1 88 1 9
Colour Valve Type D99135300
D99135300S COMPLETE STANDARD VALVED99135300C COMPLETE CATALYST VALVE (DOUBLE SEAL)
Colour Valve Spare PartsITEM NO.QTY. TYPE REF DESCRIPTION
1c 1 991.354.21 Piston1d 1 205.092.00 O Ring.1e 2 110.841.00 Screw1f 1 991.354.31 Spacer Standard Valve 6.6mm1f 2 991.354.31.m Spacer Catalyst Valve 1.95mm1h 1 991.352.15 O Ring1i 1 991.352.05 Seat (Polyethylene)1i 1 78-121 Delrin seat + O rings1i 1 92-014 O ring viton1k 1 991.354.11 Cylinder1l 1 991.352.M4 Nut
1m 1 40.10.15.06 O Ring1n 1 110.800.10 O Ring1p 1 991.356.05 Spring Seal Standard Valve1p 2 991.356.05 Spring Seal Catalyst Valve1q 1 991.352.10 Needle
D99135300
Further systems by enquiry
Spare Parts for Colour Change Manifold
ITEM NO. TYPE REF DESCRIPTION2 78-025 End Block3 78-026 Colour Change Block4 78-027 Spacer5 78-028/2 Rod 2 block set of 4 rods M8
78-028/3 Rod 3 “ “ “78-028/4 Rod 4 “ “ “78-028/5 Rod 5 “ “ “78-028/6 Rod 6 “ “ “78-028/7 Rod 7 “ “ “78-028/8 Rod 8 “ “ “78-028/9 Rod 9 “ “ “78-028/10 Rod 10 “ “ “
6 248-4422 Dome Nut M87 530-797 Washer 8 0116-24V Viton O Ring 9 293-369-50 Bolt M5X50
293-369-600 Bolt M5X6010 0140.10V Viton O Ring11 0160-10V Viton O Ring12 PO2 BP6 Plug 3/8 BSP STS13 74-002/30 Adaptor 3/8 x 1/4 BSP14 BS 38 Bonded Seal15 530.832 Split Washer 5mm16 174-811/30 Adaptor 1/8 x 1/4 BSP17 174-801/31 Washer (copper)
Pneumatic Control Panel
When required we can supply a pneumatic control panel tooperate with the colour change modules
Each panel comprises a case of suitable minimum dimensionshousing a rotary colour selection valve, solvent/off/colour switchand double acting pneumatic valves to provide fast actingvariable control of the colour valves.
Front panel clearly labelled, all connectors of push in patternand all switches fully interlocked for fail safe operation.Prices are supply only ex-works
Installation can be quoted extra if required
4 colour + solvent control panel6 colour + solvent control panel8 colour + solvent control panel10 colour + solvent control Panel12 colour + solvent control panel
Typical lead time 4-6 weeks from order.
Alternative manifold arrangements
Illustrated are two alternative systems that can be quoted on request.
The example to the left is a modular in-line six valve unit.
The other unit shown is a rotary arrangement having a very small fluidcapacity in the manifold for rapid colour changing.
Call us for further details or for a quotation.
Reference Charts
Exitflex Hoses Chemical Resistance ChartData Sheet 299-87
Reference Charts
SPRAY TIP FLOW RATESSpray tip flow rate at different pressures using water as a medium as refered to in the ExitFlextip chart where flow rate is given @ 100 Bar.
Conversion Factors1 ATM = 1.013 Bar 1 ATM/Bar = 14.5psi 1 PA = 10-5 Bar
1 MPA = 10 Bar 1psi = 0.0680 ATM/Bar 1 cm = 0.3937 Inches
1 Inch = 2.54 cm 1 Meter = 3.281 Feet 1 Foot = 0.3048 Metre
1 Litre = 0.264 USG 1 USG = 3.785 Litres 1 Litre = 0.220 UKG
1 UKG = 4.546 Litres (1.8 x ºC) + 32 = ºF 0.555 (ºF-32) = ºC
PRESSURE (Bar) FLOW (%) FACTOR20 40 X 0.4040 60 X 0.6060 75 X 0.7580 90 X 0.90100 100 X 0.10120 110 X 0.11140 120 X 0.12160 130 X 0.13180 140 X 0.14200 150 X 0.15
STANDARD SCREEN CONVERSIONSCREEN MESH THOUSANDS MICRONS MAILLES CM2 COLOUR
15 .040” 1000 50
30 .020” 500 200 GREEN
40 .015” 425 300
50 .012” 350 400
60 .010” 250 730 WHITE
66 .009” 225 850
77 .008” 205 1000
86 .007” 175 1500 BLUE
100 .006” 150 2000 YELLOW
120 .005” 125 2500
150 .004” 100 4000
165 .0036” 90 5000 RED
200 .003” 75 7000
250 .0024” 60 10000 BLACK
300 .002” 50 12000
400 .0015” 38 20000
Reference Charts
EQUIVALENT KREMLIN / EXITFLEX10° 20° 30° 40° 50° 60° 70° 80° 90° 100°8cm 13cm 18cm 23cm 28cm 33cm 38cm 43cm 48cm 53cm
0.007 03/03 03/05 03/07 03/09 03/11 03/13 03/15 03/17 03/19 03/210.009 04/03 04/05 04/07 04/09 04/11 04/13 04/15 04/17 04/19 04/210.011 06/03 06/05 06/07 06/09 06/11 06/13 06/15 06/17 06/19 06/210.013 09/03 09/05 09/07 09/09 09/11 09/13 09/15 09/17 09/19 09/210.015 12/03 12/05 12/07 12/09 12/11 12/13 12/15 12/17 12/19 12/210.017 14/03 14/05 14/07 14/09 14/11 14/13 14/15 14/17 14/19 14/210.020 20/03 20/05 20/07 20/09 20/11 20/13 20/15 20/17 20/19 20/210.024 30/03 30/05 30/07 30/09 30/11 30/13 30/15 30/17 30/19 30/210.029 45/03 45/05 45/07 45/09 45/11 45/13 45/15 45/17 45/19 45/210.033 60/03 60/05 60/07 60/09 60/11 60/13 60/15 60/17 60/19 60/210.035 68/03 68/05 68/07 68/09 68/11 68/13 68/15 68/17 68/19 68/210.044 100/03 100/05 100/07 100/09 100/11 100/13 100/15 100/17 100/19 100/21
Use references above with suffix 3 for 63-550/11 Pin type & suffix 6 for 63-552/30 Groove type AK tipsi.e. 63-552/30 14/096
EQUIVALENT DELAVAN / EXITFLEX10° 20° 30° 40° 50° 60° 70° 80° 90° 100°
8cm 13cm 18cm 23cm 28cm 33cm 38cm 43cm 48cm 53cm
0.007 A2/715 A3/725 A4/735 A5/740
0.009 B2/915 B3/925 B4/940 B5/950 B6/965
0.011 C2/1115 C3/1125 C4/1140 C5/1150 C6/1165
0.013 D2/1315 D3/1325 D4/1340 D5/1350 D6/1365 D7/1380 D8/1395
0.015 E2/1515 E3/1525 E4/1540 E5/1550 E6/1565 E7/1580 E8/1595
0.016 F2/1615 F3/1625 F4/1640 F5/1650 F6/1665 F7/1673 F8/1680 F9/1695
0.017 G2/1825 G3/1840 G4/1850 G5/1865 G6/1880 G7/1895
0.019 H2/2025 H3/2040 H4/2050 H5/2060 H6/2065 H7/2080 H8/2095
0.021 J2/2125 J3/2140 J4/2150 J5/2165 J6/2180 J7/2195
0.023 K2/2425 K3/2440 K4/2450 K5/2465 K6/2473 K7/2480
0.025 L2/2625 L3/2640 L4/2650 L5/2665 L6/2680
0.029 M2/2925 M3/2940 M4/2950 M5/2965 M6/2973 M7/2980
0.031 N2/3140 N3/1350 N4/3165 N5/3180
0.035 P2/3640 P3/3650 P4/3665 P5/3680
0.043 R3/4340 R4/4350 R5/4365 R6/4380
0.048 S2/4880
0.052 T2/5240 T3/5265
0.062 V3/6240 V4/6265
0.072 W2/7265
0.085 W3/8565
Top Quality - Best Results
The Exitflex GroupSubsidiary and Associated Companies
Exitflex (UK) Ltd5 Airfield Road, Airfield Industrial EstateChristchurch BH23 3TG United KingdomTel: +44 (0)1202 478334 Fax: +44 (0)1202 488110www.exitflex.co.uke-mail: [email protected]
Dana Marketing Pty LtdP.O. Box 2447, Rowville Victoria, AustraliaTel: (0061) 3 9752 8918Fax: (0061) 3 9752 7078www.exitflex.come-mail: [email protected]
Exitflex France SarlZi Pres de ParisAngle Rue De L’Industrie et Précision74160 Marignier, FranceTel: (0033) 450 890368Fax: (0033) 450 890186www.exitflex.come-mail: [email protected]
Exitflex GmbHHallerweiherstrasse 10D-90457 Nürnberg GermanyTel: (0049) 911 9983046Fax: (0049) 911 9983045www.exitflex.dee-mail: [email protected]
J.P. Flexibles inc254 Raritan Center ParkwayEdison, New Jersey 08837-3610 USATel: (001) 732 512 9141Fax: (001) 732 512 9145www.exitflexusa.come-mail:[email protected]
Exit SAExitflex SACh-1196, Gland SwitzerlandTel: (0041) 229999299Fax: (0041) 223642505www.exitflex.come-mail: [email protected]
© Exitflex March 2006
Distributed by:
Exitflex ABVarlabergsvagen 24BS-434 91 Kungsbacka, SwedenTel: (0046) 300 31970Fax: (0046) 300 564780www.home.swipnet.se/exitflexe-mail: [email protected]
Exit SA & Exitflex SAZone Industrielle Les Aviouilons ACH 1196 Gland, SwitzerlandTel: (0041) 229 999299Fax: (0041) 229 642505www.exitflex.come-mail: [email protected]
Exitflex PL Sp.zo.o.Plac Gornoslaski 20/581-509 Gdynia, PolandTel: (0048) 58 620 70 41Fax: (0048) 58 620 70 41www.exitflex.com & www.exitflex.ple-mail: [email protected]
Exit Hellas Trade LTD4, Akti Themistokleous, Zena MarinaGR-18536 Pireaus, GreeceTel: (0030) 1 4511322Fax: (0030) 1 4523629e-mail: [email protected]