HSA 402

AUDIO

PHONE

DATA

125 - 50/60 Hz 5A

PHONE

125 - 50/60 Hz 5A

HSA 402

DATA

IMPORTAN

T:

Go to www

.extron.com

for the com

plete

user guide

, installatio

n instructi

ons, and

specificati

ons before

connectin

g the

product to

the power

source.

1

Hideaway® Surface Access Products • Installation Guide

This guide provides instructions for an experienced installer to install and connect the Extron HSA 400, HSA 402, and HSA 822.

The HSA units are lift-up architectural solutions for inconspicuous A/V connectivity access, control, and AC power.

Planning

Determine the best location for the enclosure. Before making any cuts:

c Ensure that the location where the HSA is to be installed is convenient for as many users as possible.

c Ensure that the edge on which the HSA opens is oriented correctly.

c Ensure that there is ample space under the table for cables.

c Ensure that the correct template or dimensions are used.

Decide on the method for cutting the hole in the table.

c Hand router and template

c CNC wood router

c Jigsaw and paper template

Before starting the installation, check with local and state regulations:

c Ensure that the planned installation complies with building and electrical codes.

c Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Tools and Equipment Required for Installation

Safety Glasses

Screw Driver

Tape Measure

Vacuum Cleaner

7/16" Hex Nut Driver or Wrench (US)10 mm Hex Nut Driver or Wrench (Int’l)

1/4" Hex Nut Driver (for AAPs)Marking Pen

Square

Included Parts

HSA 400 HSA 402

Clamshell Bolts(4) sets of (2)

(various lengths)

HSA 822

COMPUTER

AUDIO

125 - 50/60 Hz 5A

HSA 400

125 - 50/60 Hz 5A

125 - 50/60 Hz 5A

HSA 402

Allen Wrench(included with HSA 400

and HSA 402 only)

Zip Ties

Icon Kit Bezel Kit

Tweeker (1)

CAT6

CAT6

CAT6

CAT6

2

Preparing the Table

WARNING: Wear safety glasses when cutting the hole in the table. Failure to comply may result in eye injury.

AVERTISSEMENT : Veillez à toujours porter des lunettes de protection lorsque vous percez la table. Ne pas respecter cela peut conduire à une blessure à l’oeil.

ATTENTION: The opening in the table for the HSA should be cut only by licensed and bonded craftspeople.• Exercise care to prevent scarring or damaging the furniture.

• Ensure that the table surface is:

• At least 3/8 inch (0.325") (9.5 mm) thick.

• No more than 1-3/4 inch (1.75") (44.5 mm) thick.

Cut a hole in the surface where the enclosure will be installed. There are three methods for cutting the hole in the table:

• A hand router and the appropriate Extron HSA routing template. See the table for par numbers.

HSA 200

USER ACCESS

HSA 200

CABLE CUBBY 300

CABLE CUBBY 300

USER ACCESS

RouterWear Safety Glasses

See the HSA Series and HSA Routing Template User Guide, available on the Extron website,www.extron.com, to prepare the template and use the template to cut the hole.

NOTE: The metal routing template is reusable. Do not discard this routing template when the installation is complete.

• A CNC wood router and the exact cut-out dimensions for your model. See the table below forcut-out dimensions:

• A jigsaw and a paper cut-out template (available on the Extron website,www.extron.com).

NOTE: The underlined dimension in the table below is the AAP and connector access side.

Template Part

Number

Surface Cut-out Dimensions

Product Width Depth

HSA 400 (USA) 70-189-01 8.14 inches (20.68 cm) 5.95 inches (15.11 cm)

HSA 400 (Int’l) 70-189-02 9.64 inches (24.49 cm) 5.95 inches (15.11 cm)

HSA 402 (USA) 70-190-01 10.37 inches (26.34 cm) 5.95 inches (15.11 cm)

HSA 402 (Int’l) 70-190-02 13.37 inches (33.96 cm) 5.95 inches (15.11 cm)

HSA 822 (all regions) 70-191-01 8.03 inches (20.40 cm) 8.33 inches (21.16 cm)

Mounting the HSA in the Table and Connecting Cables

ATTENTION: Be careful when handling and mounting the enclosure. Mishandling can damage the appearance of the enclosure.

1. Unbolt the clamshell from the enclosure (the shipped position).

2. Remove the plastic strips that protect the corners of the enclosure and the plastic film onthe finished surfaces.

3. Carefully lower the HSA into the hole to test the fit (see the image on the right, 3). Ifnecessary, carefully enlarge the opening.

4. Under the table, bolt the clamshell to the enclosure with two bolts of optimum length(4).

5. Under the table, connect the RJ-45 connectors (5).• The network cables are terminated in accordance with the TIA/EIA T568B standard

inside the HSA.

• See the drawings on the next page to understand the relationship between the RJ-45connectors on the bottom of the unit to the connectors on the faces of the unit.

User Access

Cut-O

ut Tem

plate f

or Ex

tron's

Cable

Cubb

y 200

.350"

(0.90

cm)

Print

this

templa

te

at 100%

Trim Ri

ng

Lip

Trim Ri

ng’s O

uter E

dge

0.00”

(0.00 c

m)

0.02 (0

.05 cm

)

+

1. Con

firm Pr

oduct

to be

install

ed

2. Meas

ure cu

tout an

d tem

plate

3. Afte

r chec

king, c

ut op

eningeg

HSA 400

COMPUTER

125 - 50/60 Hz 5A

HSA 400

33

5 4

HSA 400 / 402 / 822 • Installation Guide

3

Internal RJ-45 Cable Routing

Cabling and Installing the AAPs

ATTENTION: Ensure that AC power is disconnected before removing the front panel.

1. Remove and retain the four screws on the right and left sides of the front panel. Lift the panel away from the enclosure.

ATTENTION: On the HSA 822, do NOT remove the center screws. They do not fasten the AAP panel in place. They secure the AC power outlet.

2. Secure each AAP to the panel with the provided #4-40 nuts.

3. Route the AAP cables through the hole in the underside of the HSA and connect them to the rear of the AAPs.

4. Reinstall the front panel in the enclosure and secure it in place with the screws removed in step 1.

Dressing the Cables

1. Lift the HSA to extend the AAP cables to their maximum pull.

2. Experiment with AAP cable positioning to ensure that the cables do not rub against any edges and that the cable pull does not restrict the HSA lifting movement. The figures below show the recommended cable routing.

3. Route the cables as recommended in the photos below. Secure the cables in the circled locations with the provided zip ties.

HSA 400(shown w/ cables)

HSA 400

125 - 50/60 Hz 5A

Do notRemoveCenterScrew

HSA 822

HSA 822

HSA 402 Rear View

HSA 822View fromone side

Shown with clamshell removedfor clarity.

View from the opposite side

HSA 402

120-240 50/60 Hz 5A 120-240 50/60 Hz 5A

A1A2

B1

B2

A1A2

B1B2

A B

A B C D

C D

HSA 822HSA 400 / HSA 402

Present onHSA 402 Only

Present onHSA 402 Only

Extron Headquarters+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia+65.6383.4400

+65.6383.4664 FAX

Extron Japan+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East+971.4.299.1800

+971.4.299.1880 FAX

EExtron Australia+61.8.8351.2188+61.8.8351.2511 FAX

Extron India1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

© 2017 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com 68-2107-50 Rev B 01 17

Installation Checklist

Planning (page 1)• Choose a location. Consider the following:

• Ensure that the edge on which the lid opens faces the table position of the most likely user.

• Ensure that there is ample space under the table for cable routing.

• Ensure that there is a nearby electrical outlet.

Preparing the Table (page 2)• Ensure that you are using the correct template or dimensions.

• Cut the hole.

Mounting the HSA (page 2)• Install the HSA and secure the clamshell.

• Connect the RJ-45 cables.

Installing the AAPs (page 3)• Install the AAPs.

• Route and connect the AAP cables.

Dressing the Cables (page 3)• Dress the cables out of the way to prevent lifting restrictions.

Connect the HSA AC Power

4

http://www.extron.com