Upload
neoa
View
231
Download
0
Embed Size (px)
Citation preview
8/12/2019 Herz Strmax m
1/10
D ata S heet for
4117 M
Edition 1203 (1203)Circuit Regulating Valve for Differential Pressure Measurement,
Inclined Model, with Measuring Valves
W e reserve the right to alter thesp ec ifica tion w itho ut prior notice.
Order Numbers
4117 M 1/2, 3/4
D im ensions 1/2 and 3/4w ithout thread ed plugright bottom side,one m easuring valve isfitted on one side.
Models
1 4117 51 (D N 15) 1/2 65 86 49
1 4117 52 (D N 20) 3/4 75 92 52
1 4117 53 (D N 25) 1 90 105 56
1 4117 54 (D N 32) 1 1/41/4
110 118 60
1 4117 55 (D N 40) 1 1/2 120 127 62
1 4117 56 (D N 50) 2 150 155 69
1 4117 57 (D N 65) 2 1/2 180 205 78
1 4117 58 (D N 80) 33/8
210 226 83
2 m easuring valves are fitted and are sealed at the factory.
1 0284 01 1/4 Q uick m easuring valve for H ERZ-STR M AX C ircuit Regulating Valve,blue cap, for pressure absorption device
1 0284 02 1/4 Q uick m easuring valve for H ERZ-STR M AX C ircuit Regulating Valve,
red cap, for pressure absorption device
4117 M STRMAX-M Circuit Control Valves with Measuring ValvesInclined brass version, socket x socket, O -ring spind le seal,presetting by lim itation of valve lift outside the w ater cham ber.
DN 15-DN 20 2 bore holes of 1/4 w ith m easuring valves,1 bore hole of 1/4 closed w ith screw plug 1 0273 09
DN 25-DN 50 2 bore holes of 1/4 w ith m easuring valves,2 bore holes of 1/4 closed w ith screw plug1 0273 09
DN 65-DN 80 2 bore holes of 1/4 w ith m easuring valves,2 bore holes of 3/8 closed w ith screw plug 1 0273 00
D rain cocks m ust be ordered separately.
Measuring valves
Other Regulating Valves
Valves withMeasuring Valves
4217 GM DN 15-DN 80 STR M A X-G M -C ircuit R eg ulating Valve for differential pressurem easurem ent, srew -dow n-m od el, w ith m easuring valves
4218 MFS DN 50-DN 200 STR M A X-M FS -C ircuit R eg ulating Valve for differential pressurem easurem ent, flanged version, inclined-m od el, w ith m easuring valves
4218 GMF DN 25-DN 80 STR M A X-G M F-Circuit R eg ulating Valve for differential pressurem easurem ent, flanged version, srew -dow n-m od el,w ith m easuring valves
O rder no.R
R 1 LH 1 H 2
C onnection open
HERZ ArmaturenRichard-Strauss-Strae 22 A-1230 Wien
e-mail: [email protected] www.herz-armaturen.com
1
Presetting sleeveLocking nut
Flowdirection
for presettingvalues
8/12/2019 Herz Strmax m
2/10
Operating dataM axim um operating tem perature 110 CM axim um operating pressure 10 barH ot w ater quality according to N O R M H 5195 and . VD I-guideline 2035.
Pipe Connection withCompression Union
C ircuit R eg ulating Valves R =12 (D N 15) are fitted w ith special sockets or w ith a directly connectionfor com pression unions.You can use d im ensions D N 20 and D N 25 also by m eans of an adapter for a com pression union.
In case of installation of soft steel or copper pipes w ith com pression unions, w e recom m end the useof support sleeves. The thread of the locking nut (m ale or fem ale thread ) as w ell as the olive m ust belubricated w ith silicone oil. W e d raw attention to our instructions for installation.
For models 4117 M until year of construction 2003270 1/43/8 D raining valve w ith hand le272 1/43/8 Screw plug275 1/43/8 D raining valve w ith handle and hose connection
For models 4117 M as of 2003 - new design271 1/4 D raining valve w ith hand le273 1/4-3/8 Screw plug276 1/4-3/8 D raining valve w ith handle and sw ivelling hose connectionH ose connection 1 6206 01 has to b e ordered sep arately.
Draining Fittings to beordered separately
W hen using H ER Z-com pression unions for copper and steel pipes, ob serve the perm issible tem -peratures and pressures as specified in E N 1254-2:1998 Tab le 5. A m axim um operating tem pera-ture of 95 C and m axim um op erating pressure of 10 bar ap plies for plastic p ipe connections, ifperm itted by the pipe m anufacturer.
HERZ-CompressionUnion
2
Pipe D m m 8 10 12 14 15 16 18
Valve D N 15
Adapter O rder no. 1 6266 01 1 6266 01
1 6292 14
1 6266 01 1 6266 01
Com pr.union O rder no. 1 6274 18 1 6274 00 1 6292 12 1 6292 01 1 6274 04 1 6274 04
C om pr.union soft seal
O rder no. O ptional1 6275 04 1 6276 18
Pipe D m m 8 10 12 14 15 16 18
Valve D N 20
Adapter O rder no. 1 6266 20 1 6266 20 1 6266 20 1 6266 20
1 6274 02
1 6266 20 1 6266 20 1 6266 20
Com pr.union O rder no. 1 6274 18 1 6274 00 1 6274 01 1 6274 03 1 6274 04 1 6274 04
C om pr.union soft seal
O rder no. O ptional1 6276 12 1 6276 15 1 6276 18
Pipe D m m 8 10 12 14 15 16 18 22
Valve D N 25
A d ap ter O rd er no. P 1928 05 P 1928 05 P 1928 05 P 1928 05 P 1928 05
1 6274 03
P 1928 05 P 1928 05 1 6266 03
Com pr.union O rder no. 1 6274 18 1 6274 00 1 6274 01 1 6274 02 1 6274 04 1 6276 18 1 6273 01
8/12/2019 Herz Strmax m
3/10
Pipe D m m 14x2
Valve D N 15
A dapter O rder no.
C o m p r.union O rd er no. 1 6092 02
C om pr.union soft seal
O rder no. O ptional
Pipe D m m
Valve D N
A dapter O rder no.
Com pr.union O rder no.
C om pr.union soft seal
O rder no. O ptional
16x2
1 6092 01
16x2,2
1 6266 01
1 6097 12
1 6098 12
17x2
1 6266 01
1 6097 04
1 6098 04
17x2,5
1 6266 01
1 6097 05
1 6098 05
18x2
15
1 6266 01
1 6097 07
1 6098 07
18x2,5
1 6266 01
1 6097 06
1 6098 06
20x2
1 6266 01
1 6097 08
1 6098 08
20x2,5
1 6266 01
1 6097 11
1 6098 11
20x3,5
1 6266 01
1 6097 10
1 6098 10
Pipe D m m 14x2
Valve D N 20
A dapter O rder no. 1 6266 20
C o m p r.union O rd er no. 1 6097 02
C om pr.union soft seal
O rder no. O ptional1 6098 02
16x2
1 6266 20
1 6097 03
1 6098 03
16x2,2
1 6266 20
1 6097 12
1 6098 12
17x2
1 6266 20
1 6097 04
1 6098 04
17x2,5
1 6266 20
1 6097 05
1 6098 05
Pipe D m m
Valve D N 20
A dapter O rder no.
Com pr.union O rder no.
C om pr.union soft seal
O rder no. O ptional
18x2
1 6266 20
1 6097 07
1 6098 07
18x2,5
1 6266 20
1 6097 06
1 6098 06
20x2
1 6266 20
1 6097 08
1 6098 08
20x2,5
1 6266 20
1 6097 11
1 6098 11
20x3,5
1 6266 20
1 6097 10
1 6098 10
Pipe D m m 14x2
Valve D N 25
A dapter O rder no. P 1928 05
C o m p r.union O rd er no. 1 6097 02
C om pr.union soft seal
O rder no. O ptional1 6098 02
16x2
P 1928 05
1 6097 03
1 6098 03
16x2,2
P 1928 05
1 6097 12
1 6098 12
17x2
P 1928 05
1 6097 04
1 6098 04
17x2,5
P 1928 05
1 6097 05
1 6098 05
Pipe D m m
Valve D N
A dapter O rder no.
Com pr.union O rder no.
C om pr.union soft seal
O rder no. O ptional
18x2
25
P 1928 05
1 6097 07
1 6098 07
18x2,5
P 1928 05
1 6097 06
1 6098 06
20x2
P 1928 05
1 6097 08
1 6098 08
20x2,5
P 1928 05
1 6097 11
1 6098 11
20x3,5
P 1928 05
1 6097 10
1 6098 10
25x3,5
1 6266 03
1 6198 00
26x3
1 6266 03
1 6198 01
3
Plastic Pipe ConnectionInclined circuit regulating valves R = 1/2 (D N 15) are suitable for installations w ith plastic pipes.A dap ter and plastic pipe connections can be fitted to the special sockets. For m od els and dim en-sions please refer to the H ER Z-catalog ue.
8/12/2019 Herz Strmax m
4/10
Special Design Features
Thermal Insulation ShellsCode no. 4095
Differential PressureMeasurement
Flow directionsThe valve is suitable for flow in either direction thanks to the pivoting, non-rem ovab le cone. The flowdiag ram s are ap plicable for the flow direction ind icated on the draw ing .
Seat sealThe tem perature-resistant and perm anently elastic soft seal is corrosion-resistant, perm its operationw ith low shutting forces and is ap proved for a m axim um op erating tem perature of 150 C .
Spindle sealThe O -ring seal ensures lasting tightness and ease of valve op eration. The O -ring cham ber can berep laced. O rder num ber 1 6705 00
Pre-settingTo avoid leakage of w ater presetting is carried out by lim itation of valve lift outside the w atercham ber.
Pre-setting markerThe pre-setting m arker (1 6517 05) is fastened as a tag ab ove the valve or pipe. The setting of theresp ective valve is m arked by cutting or breaking off the teeth at the figures for full and partial turns.This p erm its checking and/or restoration of the original pre-setting m ad e on the occasion of systemset-up after servicing w ithout having to rely on d ocum entation.
For insulation purposes and to avoid loss of heat we recom m end the fitting of therm al insulationshells.
These consist of tw o interlocking half shells and the spindle seal. The parts are closed by overlap -ping and held tog ether by m eans of tightening strap s. The therm al insulation shells can b e rem o-ved and reused at any tim e (e.g. pre-setting at a later date).
Therm al insulation shells can be used for m ax. 120 C op erating tem perature.For m od els and dim ensions please refer to H ER Z-catalogue.
The STR M A X-M circuit control valve is eq uipped w ith tw o m easuring valves, one before and oneafter the valve seat. The differential pressure can be m easured using a suitab le m easuring instru-m ent w hich perm its calculation of the flow rate as a function of the resp ective presenting step. TheH ER Z-m easuring com puter ( 1 8902 00) perm its d irect flow rate reading (consult the eq uipm entm anual).
Measuring ValveOperation
The tw o m easuring valves installed are eq uipped w ith a soft seal.
Warning: O pening of the m easuring valves is perm itted only w hen a m easuring instrum ent isconnected . O therw ise, hot w ater m ay cause injury.
The H ER Z-m easuring com puter has suitable coupling s w ith O -ring seals and securing screw s, ensu-ring perfect fastening on the m easuring valves.
Prior to m easuring , the coup ling s m ust be attached and secured . O nly afterw ards is it perm itted toop en the m easuring valve by approxim ately half a turn using the H ER Z-universal key (1 6640 00) or
an 8 m m open-end w rench.A fter m easuring , first shut the m easuring valve and only then rem ove the coup ling s from them easuring valve.
4
Pre-setting, adjustmentand fixing withmeasuring instrument
1. The S TR M A X-M valve is delivered w ith fully op ened presetting (m ax. flow ).2. A fter connecting the H ER Z-different m anom eter and ad justing to the correct reg ulating step (see
eq uipm ent m anual) loosen the locking nut and w ithout adjusting the spind le turn the presettingsleeve to the right by hand to its lim it.
3. Fix the presetting sleeve w ith locking nut.4. R em ove the m easuring instrum ent according to the op erating instructions.
W hen the valve is closed the ad justed presetting step can now be seen.
Presetting by meansof the presetting sleeve
1. C lose the valve.2. U nscrew the locking nut (below the presetting sleeve).3. Turn the presetting sleeve to the desired position on the spind le scale. The presetting value
should be d eterm ined from the diag ram overleaf.4. Fix the presetting sleeve at the desired value by m eans of the locking nut.
C A U TIO N : The valve m ust be closed during the setting !
8/12/2019 Herz Strmax m
5/10
Presetting by meansof the handwheel
The presetting step s m atch the turns of the hand w heel. O ne turn corresp onds to one presetting step .If you cannot see the presetting step s on the scale you can ad just by counting the turns (starting fronthe closed value).
Handling1. C lose the valve.2. U nscrew the locking nut.3. B y counting the turns of the hand w heel preset to the desired position.4. Fix the p resetting sleeve w ith the locking nut.
Accessories
Spare Parts
1 4095 Therm al heat shells for order num bers p lease refer to the H ER Z catalog ue1 6517 05 Pre-setting m arker1 8900 03 H ER Z-M easuring com puter for one-hand operation
1 8903 00 H ER Z-M easuring com puter Flow plus
For models 4117 M until year of construction 2003
1 0280 09 M easuring valve, straight m odel1 0282 09 M easuring valve, angle m odel1 6388 00-08 STR M A X-M - up per part for order num bers please refer to the H ER Z-catalog ue1 6518 00 H and w heel1 6705 00 O -ring set1 6640 00 H E R Z -universal key
For models 4117 M as of 2003 - new design
1 0284 01 1/4 Q uick m easuring valve for H ER Z-STR M AX C ircuit R egulating Valve,blue cap, for pressure absorption device
1 0284 02 1/4 Q uick m easuring valve for H ER Z-STR M AX C ircuit R egulating Valve,red cap, for pressure absorption device
1 6388 50-58 STR M AX-M - upper part - for order num bers please refer to theH ER Z-catalogue
1 6518 00 H and w heel1 6705 00 O -ring set
5
8/12/2019 Herz Strmax m
6/10
4117M
1/2
4117M
3/4
6
1
0,5
0,1
0,0
5
0,0
1
0,0
05
1
0,5
0,1
0,05
0,0
1
0,0
05
flowd
irection(Q)
pressuredecrease(p)
pressuredecrease(p)
flowd
irection(Q)
8/12/2019 Herz Strmax m
7/10
4117M
1
4117
M
11/4
7
1
0,5
0,1
0,0
5
0,0
1
0,0
05
1
0,5
0,1
0,0
5
0,0
1
0,0
05
flowd
irection(Q)
flowd
irection(Q)
pressuredecrease(p)
pressuredecrease(p)
8/12/2019 Herz Strmax m
8/10
4117M
11/2
4111
7M
2
8
Presetting values with HERZ Differential Manometer
flowd
irection(Q)
flowd
irection(Q)
pressuredecrease(p)
pressuredecrease(p)
8/12/2019 Herz Strmax m
9/10
4117M
21/2
411
7M
3
9
flowd
irection(Q)
flowd
irection(Q)
pressuredecrease(p)
pressuredecrease(p)
8/12/2019 Herz Strmax m
10/10
4117 M-1/2
kv-ValueZeta-Valueacc. to DIN
2440kv-Value kv-Value kv-Value
4117 M-3/4 4117 M-1 4117M-11/4
4117 M-34117M-21/24117M-24117 M-11/2
10
HERZ ArmaturenRichard-Strauss-Strae 22 A-1230 Wien
e-mail: [email protected] www.herz-armaturen.com
Presetting values with HERZ-Differential Manometer
presetting-level Zeta-Valueacc. to DIN
2440
Zeta-Valueacc. to DIN
2440
Zeta-Valueacc. to DIN
2440
kv-ValueZeta-Valueacc. to DIN
2440kv-Value kv-Value kv-Value
presetting-level Zeta-Valueacc. to DIN
2440
Zeta-Valueacc. to DIN
2440
Zeta-Valueacc. to DIN
2440