Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Heavy Duty Turning Center
The PUMA 500 turning centers are the most powerful machines in their class. Designed for heavy and interrupted cutting, holding long term accuracies, and maintaining superior finishes. High metal removal rates along with rapid positioning and high speed turret indexing, guarantee unmatched cycle times when real performance is essential. Proven manufacturing techniques and ultra rigid construction are combined with advanced technological features to produce superior machine with exceptional values.
The Most Powerful Machines in Their Class
2
3
Main Spindle
The 45 kW(PUMA 500) spindle motor provides power for heavy stock removal,greatly reducing the number of roughing passes required. The reliable digital ACspindle motor provides fast acceleration and is maintenance free. The preloadedspindle bearings are specifically calibrated to maintain the perfect balance of rigidityand speed. The geared headstock ensures optimal power throughout a wide speedrange. Full power is available from 76 r/min on the where the low end torque is 5645N.m. The large diameter spindle can handle chucks up to 813 mm in diameter.
T=564
5 N. m
r/min
T=220
5 N. m
T=839
N. m
45kW 30min
● Spindle speed range : 1500 r/min●Motor power : 45kW
Main Spindle Drive
Max. spindle speed
11550000 r/min
4455 kW
Motor (30 min)
The headstock casting is made of Meehanite andribbed on the outside to increase the surface area forbetter heat dissipation. The headstock and mainspindle are manufactured in a temperaturedcontrolled environment then assembled and testedin our clean room. The heavy duty cartridge typespindle is supported by a double row of cylindricalroller bearings in the front and rear, with duplexangular thrust bearings in between. The cylindricalroller bearings feature a large contact surface whichensures the highest rigidity for heavy loads andsuperior finishes. All spindle bearings arepermanently grease lubricated precision class P4.
Headstock and Spindle Construction
Headstock Cross Section
4
■Main spindle power-torque diagram
Power is delivered to the spindle through a threespeed geared head allowing high spindle speeds aswell as powerful low end torque.
Geared Head
00..2255 sIndex time (1-station swivel)
1122 stationsNo. of tool station
The large 12 station heavy duty turretfeatures a large 400 mm Curvic couplingdiameter and 213640 N of hydraulic clampforce. This heavy duty design providesunsurpassed rigidity for heavy stockremoval, fine surface finishes, and extendedtool life. The exceptionally stable turret has avery wide 150 mm turret plate to ensurelong boring bar over-hang ratios. Indexingrepeatability is ±0.0005 degrees. Turretindexing is non-stop bi-directional. Anextremely reliable high-torque hydraulicmotor provides for quick turret indexing. 32mm square tool holders are mounteddirectly to the turret. The boring bar capacityis 80 mm. The turret features a flexibledesign, allowing for left or right handed, IDor OD tool placement.
The turret features BMT styletooling in which the toolholders are mounted directiyto the turret’s periphery using4 large bolts. This type ofmounting system allows aextremely high degree ofrigidity.
Turret
TURRET SADDLEHeavy Duty Turret
5
Each axis is powered by a maintenance freedigital AC servo motor. These high torquedrive motors are connected to the ball screwswithout intermediate gears for quiet andresponsive slide movement with virtually nobacklash.
Asix Drives
The programmable tailstock body is mountedon the same guideway surface as theheadstock. The heavy casting, large 150 mmdiameter quill, and precision Morse Taper #6live center provide outstanding rigidity. The150 mm quill stroke is activated by either theprogram and foot switch. Auto lubrication isprovided to the quill and guideways.
Programmable TailstockDouble Pretensioned Ball Screw
Axis Drive Construction and Tail Stock
Both the X and Z axes feature doublepretension ed ball screw, supported on eachend by precision class P4 angular contactthrust bearings. Both axes are driven by largediameter, high precision ball screws. Each ballscrew has been carefully selected to achieve acombination of high accuracy, high rapidtraverse rates and high feed thrust. All ballscrews are fully supported on both ends.
Bed and Way Construction
Rapid Traverse
Doosan Infracore precision machine tools are internationally known for theirdurability, rigidity and high accuracy. Only well proven and time testedmanufacturing techniques can produce machines of this quality.
The PUMA 500 is a true 60 degree slant beddesign. The bed is a one piece casting with boththe saddle and tailstock guideways in the sameplane to eliminate thermal distortion. The heavilyribbed torque tube design prevents twisting anddeformation. Fine grain Meehanite processed castiron is used because of its excellent dampeningcharacteristics. This design ensures high rigiditywith no deformation during heavy cutting. Theslant angle allows for easy loading , changing andinspection of tools. All guide ways are groundwrap-around rectangular type for unsurpassedlong-term rigidity and accuracy. The guideways arewidely spaced to ensure stability and fully
protected. Each guideway is induction hardenedand precision ground. A fluroplastic resin, RulonⓇ
142, is bonded to the mating surfaces, for its wearand low friction characteristics and then handscraped for a perfect fit and center height.
6
•Scraping of Slideway •Outstanding rigidity for high feedrates
1100 m/min
X-axis
1122 m/min
Z-axis
Slant-design bed makes the work go smoother, chipremoval much easier. Tough tubular construction stands upto the hardest cutting jobs.
7
The coolant is kept clean and its life is extended with bed castingchannels from the Z axis to a separate reservoir. A belt oil skimmer picksup and removes waste oil from the coolant tank that is easily drained.
The high pressure flushes chips out of drilled holes, reduces theneed for peck drill cycles, exceeds the requirements of mostinsert drill manufactures and significantly increases tool life.
The separate, large 310L capacity coolant tank and chip pan areseparate from the machine bed to prevent heat transfer and easycleaning.
Eco-Friendly Design
Metered Way Lubrication
Hydraulic Power Unit
Oil Skimmer(Opt.)
Automatic lubrication is provided to all guideways, ball screws andthe tailstock quill. A maintenance free piston distributor delivers aprecise quantity of oil to each lubrication point. The 2.7L reservoirlasts up to 80 hours. A low level alarm prevents the machine fromrestarting without lubricant.
Automatic Tool Setter(Opt.)
Coolant System
The automatic tool setter reduces set-up time by minimizing theneed for skim cuts, measurements and entering tool offsets. The toolsetting arm is moved by an electric motor and can be controlledthrough the program.
unit : mm
unit : mm
Tooling System
Tool Interference Diagram
8
unit : mm
External Dimension
R57
4R597
R684
R649
R57
4R
594R570
R344
597
2455
560
R600
4930684
5579
3612
3150
4800
205 1445 130
1404
6204
1005
1165
650
2250
275 785 880 515
2202
38
7
2589
1394 10
950
980
TTOOPP VVIIEEWW
RRiigghhtt SSiiddee VVIIEEWW FFRROONNTT VVIIEEWW
9
Working Ranges
•Design and specifications are subject to change without prior notice.•We are not responsible for difference between the information in the catalog and the actual machine.
Swing over bed mm 900
Swing over saddle mm 630
Recom. Turning diameter mm 450
Max. turning diameter mm 700
Max. turning length mm 1575
Bar working diameter mm 117
X-axis travel mm 370
Z-axis travel mm 1575
Spindle speed r/min 1500
Spindle nose ASA A2#15
Spindle bearing diameter mm 200
Spindle through hole diameter mm 152
No. of tool stations st 12
OD tool size mm 32
Boring bar diameter mm Ø80
Indexing time (1st. swivel) s 0.25
Quill diameter mm 150
Quill bore taper MT MT#6
Quill travel mm 150
Rapid traverse(X-axis) m/min 10
Rapid traverse(Z-axis) m/min 12
Main spindle motor(30min) kW 45
Feed motor(X/Z-axis) kW 4.0 / 7.0
Coolant pump motor kW 0.4
Electric power supply (Rated capacity) kVA 63.6
Machine height mm 2587
Machine dimensions (W × L) mm 2455 × 5009
Machine weight kg 14000
CCaappaacciittyy
IItteemm PPUUMMAA 550000
CCaarrrriiaaggee
MMaaiinn SSppiinnddllee
TTooooll PPoosstt
TTaaiill SSttoocckk
FFeeeeddrraattee
MMoottoorrss
PPoowweerr SSoouurrcceeMMaacchhiinneeSSiizzee
Machine Specifications
Standard Feature■ Coolant supply equipment■ Full enclosure chip and coolant shield■ Hand tool kit, including small hand tool
for operations
■ Hydraulic chuck & actuating cylinder■ Hydraulic power unit■ Leveling jack screw & plates■ Lubrication equipment
■ Programmable Tailstock & Live center■ Soft jaws (total 5sets)■ Standard tooling kit (tool holder & boring sleeve)■Work light (1set)
Optional Feature■ Air blast for chuck jaw cleaning■ Automatic door with safety device■ Automatic measuring system (in process touch probe)■ Automatic power off■ Bar feeder interface■ Chip conveyor ■ Chip bucket■ Controller : Fanuc 18i-TB
■ Tool monitoring system■ Dual chucking pressure■ Hardened & ground jaws■ High pressure coolant pump■ Oil skimmer■ Programmable Tailstock &
Built-in center (MT#5)■ Signal tower (yellow, red, green)
■ Pressure switch for chucking pressure check■ Steady rest
- Hydraulic, or- Manual
■ Tool pre-setter- Hydraulic, or- Manual
10
CCoonnttrroollss
AAxxiissFFuunnccttiioonnss
OOppeerraattiioonn
IInntteerrppoollaattiioonn
FFeeeedd FFuunnccttiioonnss
AAxxuuiilliiaarryy &&SSppiinnddllee FFuunnccttiioonnss
PPrrooggrraammmmiinnggFFuunnccttiioonnss
EEddiittiinngg OOpp..FFuunnccttiioonnss
SSeettttiinngg && DDiissppllaayy
DDaattaa IInnppuutt &&OOuuttppuutt
TTooooll FFuunnccttiioonnss
OOtthheerr FFuunnccttiioonnss
IItteemm SSppeecc.. FFaannuucc 2211ii--TTBB FFaannuucc 1188ii--TTBB
Controlled axes X, Z X, ZSimultaneously controlled axes Std. 2 axes ○ ○Backlash compensation 0~±9999 pulses ○ ○Cs contouring control - -Follow-up / Chamfering on/off ○ ○HRV control ○ ○Least input increment 0.001mm / 0.0001″ ○ ○Stored stroke check1 Overtravel control ○ ○Automatic operation(memory) / Buffer register ○ ○Manual handle feed rate X1, X10, X100 ○ ○Search function Sequence NO. / Program NO. ○ ○1st, 2nd reference position check / return G27/G28, -/G30 ○ ○Circular interpolation G02, G03 ○ ○Continuous thread cutting ○ ○Dwell G04 ○ ○Linear interpolation G01 ○ ○Multiple threading /Thread cutting retract ○ ○Polar coordinate interpolation G12.1, G13.1 - -Thread cutting / Synchronous cutting ○ ○Feed per minute / Feed per revolution G98 / G99 ○ ○Feedrate override 0 - 200 % (10 % unit) ○ ○Jog feed override 0 - 2000 mm/min ○ ○Rapid traverse override F0/ 25 / 100 % ○ ○Tangential speed constant control ○ ○1st Spindle orientation ○ ○Constantant surface speed control G96, G97 ○ ○M-function M3 digit ○ ○Multi-spindle control - -Rigid tapping ○ ○Spindle speed override 0~150 % ○ ○Absolute / Incremental programming ○ ○Canned cycle for drilling G80 series ○ ○Custom macro B ○ ○Decimal point programming/pocket calculator type decimal point programming ○ ○Direct drawing dimension programming ○ ○eZ Guide i Conversational programming ○ ○Maximum program dimension ±99999.999mm/(±9999.9999 inch) ○ ○Multi repetitive canned cycle G70~G76 ○ ○Multi repetitive canned cycle 2 ○ ○Optional block skip(without hardware) Total 9(Only NC function) ○ ○Program number / Sequence number O4 digits / N5 digits ○ ○Programmable data input G10 ○ ○Sub program call Nested holds4 4 4Tape format for FANUC series 10/11 ○ -Tape format for FANUC series 15 - ○Work coordinate system selection G52, G53, G54~G59 ○ ○Auto tool offset ○ ○Tool monitoring system Opt. Opt.Direct input of tool offset value measured B ○ ○Tool geometry / wear compensation Geometry & wear data ○ ○Tool life management ○ ○Tool nose radius compensation G40~G42 ○ ○Tool number command(T-code function) T2+2 digits ○ ○Tool offset pairs 64 32Tool offset value counter input ○ ○Background editting ○ ○Expanded part program editting Copy, Move, Change of NC program ○ ○No. of Registered programs 200ea 125eaPart program editing / Program protect ○ ○Part program storage length*1 640m 640mDisplay of spindle speed and T-code at all screen ○ ○Help function Alarm&Operation display ○ ○Self diagnostic function ○ ○Servo setting screen / Spindle setting screen ○ ○Status display / Lock function ○ ○Tool path graphic display - -External key input / External data input ○ ○External work number search ○ ○I/O interface RS - 232C ○ ○Memory card input and output ○ ○Reader puncher control CH1 interface ○ ○Ethernet function Embedded ethernet function ○ ○MDI / DISPLAY unit 10.4″color LCD 10.4″color LCDPMC system ○ ○
◯ : Standard OPT : Option (!) : only M type *1 : Standard Part program length is different on export condition. On the addition of optional functions, its length can be reduced.
NC Unit Specifications
11
http://domss.doosaninfracore.com
Design and specifications are subject to change without prior notice. EU0804SPi-ser
Sales & Support Network
ARGENTINA/Rosario AUSTRALIA/Melbourne/Sydney AUSTRIA/Vienna BELGIUM/Gullegem BRAZIL/Sao paulo BULGARIA/Sofia CANADA/Edmonton/Montreal/Toronto
/Vancouver CHILE/Santiago CHINA/Beijing/Chongqing/Guangzhou/Shanghai/Shenyang COLOMBIA/Bogota CZECH/Brno DENMARK/Randers EGYPT/Cairo FINLAND/Tampere
FRANCE/Annecy GERMANY/Dusseldorf GREECE/Athens HONG KONG/Kowloon HUNGARY/Budapest INDIA/Bangalore/Pune INDONESIA/Jakarta ISRAEL/Herzlia
ITALY/Parma MALAYSIA/Puchong MEXICO/Guadalajara /Mexico City /Monterrey /Vera Cruz NETHERLANDS/Goorn NEW ZEALAND/Auckland NORWAY/Oslo PAKISTAN
/Islamabad POLAND/Krakow PORTUGAL/Lisbon ROMANIA/Bucharest RUSSIA/Moscow SINGAPORE/Singapore SLOVENIA/Ljubljana SOUTH AFRICA/Kempton Park
SPAIN/Barcelona SWEDEN/Stockholm SWITZERLAND/Zurich TURKEY/Istanbul THAILAND/Bangkok U.A.E/Sharjah U. K./Leamington U.S.A./Atlanta/Birmingham
/Charlotte/Chicago/Cincinnati/Cleveland/Dallas/Denver/Detroit/Houston/Indianapolis/Kansas City/Little Rock/Los Angeles/Milwaukee/Minneapolis/New Orleans/Norfolk/Philadelphia/Phoenix
/Pittsburgh/Portland/Rochester/Salt Lake City/San Diego/San Francisco/Seattle/Springfield/St. Louis/Tampa/Trenton/Tulsa VENEZUELA/Valencia VIETNAM/Hanoi
Head Office : Doosan Tower 22nd FL., 18-12, Euljiro-6Ga, Jung-Gu, Seoul, Korea 100-730Tel : ++82-2-3398-8651 Fax : ++82-2-3398-8699 E-mail : [email protected]
Doosan Infracore America Corp.: 8 York Avenue, West Caldwell, NJ 07006, U.S.A.Tel : ++1-973-618-2500 Fax : ++1-973-618-2501
Doosan Infracore Germany GmbH : Hans-Böckler-Strasse 29, D-40764 Langenfeld-Fuhrkamp, Germany.Tel : ++49-2173-8509-10 Fax : ++49-2173-8509-60
China Representative Office : 9-101 Xinmao Building, 99 Tianzhou Road, Caohejing Hi-Tech Development Shanghai, China 200233 Tel : ++86-21-5445-1155 (812,815) Fax : ++86-21-64403389