HCD-NXM4D

HCD-NXM4Dl

SERVICE MANUAL

DISPLAY SIDE Hi-Fi COMPONENT SYSTEMSony CorporationAudio GroupPublished by Sony Engineering Corporation

9-877-971-032005E02-1© 2005.05

SPECIFICATIONS

Ver. 1.2 2005.05

– Continued on next page –

• HCD-NXM4D is the Amplifier, DVD player,tape deck and tuner section in DHC-NXM4D.

Model Name Using Similar Mechanism NEW

DVD DVD Mechanism Type CDM81A-DVBU60

Section Base Unit Name DVBU60

Optical Pick-up Name DBU-3

TAPEModel Name Using Similar Mechanism HCD-CPX22

Section

Main unitAmplifier sectionThe following measured at AC 120, 127, 220, 240 V, 50/60 HzDIN power output (rated): 60 + 60 watts

(6 ohms at 1 kHz, DIN)Continuous RMS power output (reference)Front speaker: 75 + 75 watts

(6 ohms at 1 kHz, 10% THD)Center speaker: 40 watts (6 ohms at 1 kHz, 10% THD)Surround speaker: 40 + 40 watts

(6 ohms at 1 kHz, 10% THD)Sub woofer: 120 watts

(4 ohms at 100 Hz, 10% THD)InputsVIDEO/SAT IN (phono jacks):

voltage 250/450 mV, impedance 47kilohms

MIC1/MIC2 (phone jacks): sensitivity 1 mV, impedance 10kilohms

OutputsVIDEO/SAT OUT (phono jacks):

voltage 250 mV, impedance 1 kilohmVIDEO OUT (phono jack): max. output level

1 Vp-p, unbalanced, Sync negative,load impedance 75 ohms

S VIDEO OUT (4-pin/mini-DIN jack):Y: 1 Vp-p, unbalanced,Sync negative, C: 0.286 Vp-p, loadimpedance 75 ohms

COMPONENT VIDEO OUT:Y: 1 Vp-p, 75 ohmsPB, PR: 0.7 Vp-p, 75 ohms

PHONES (stereo mini jack): accepts headphones of 8 ohms ormore

FRONT SPEAKER: Use only the supplied speakerSS-NXM4D

SURROUND SPEAKER: Use only the supplied speakerSS-RS400S

CENTER SPEAKER : Use only the supplied speakerSS-CT400S

SUB WOOFER SPEAKER: Use only the supplied speakerSS-WG4D

2

HCD-NXM4D

Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Flexible Circuit Board Repairing• Keep the temperature of soldering iron around 270˚C

during repairing.• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering

or unsoldering.

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.

This appliance is classified asa CLASS 1 LASER product.This label is located on the rearexterior.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.

Disc player sectionSystem Compact disc and digital audio and

video systemLaser Semiconductor laser

(DVD: λ=650 nm, CD: λ=780 nm)Emission duration: continuous

Frequency response DVD (PCM 48 kHz):2 Hz – 22 kHz (±1 dB)CD: 2 Hz – 20 kHz (±1 dB)

Video color system format Latin American model: NTSCOther models: NTSC, PAL

Tape deck sectionRecording system 4-track 2-channel stereoFrequency response 50 – 13,000 Hz (±3 dB), using Sony

TYPE I cassette

Tuner sectionFM stereo, FM/AM superheterodyne tunerFM tuner sectionTuning range 87.5 – 108.0 MHz (50 kHz step)Antenna FM lead antennaAntenna terminals 75 ohms unbalancedIntermediate frequency 10.7 MHzAM tuner sectionTuning rangeLatin American models: 530 – 1,710 kHz

(with the interval set at 10 kHz)531 – 1,710 kHz(with the interval set at 9 kHz)

Saudi Arabian models: 531– 1,602 kHz(with the interval set at 9 kHz)

Other models: 531 – 1,602 kHz(with the interval set at 9 kHz)530 – 1,710 kHz(with the interval set at 10 kHz)

Antenna AM loop antennaAntenna terminals External antenna terminalIntermediate frequency 450 kHz

GeneralPower requirementsAustralian model: 230 – 240 V AC, 50/60 HzSaudi Arabian model: 120 – 127 V or 220 – 240 V AC,

50/60 HzAdjustable with voltage selector

Thai model: 220 V AC, 50/60 HzOther models: 120 V or 220 – 240 V AC, 50/60 Hz

Adjustable with voltage selectorPower consumption 315 watts

Dimensions (w/h/d) Approx. 230 x 290 x 355 mmMass Approx. 7.0 kg

Design and specifications are subject to change without notice.

3

HCD-NXM4D

TABLE OF CONTENTS

1. SERVICING NOTES ................................................ 4

2. GENERALLocation of Controls ........................................................ 5

3. DISASSEMBLY3-1. Disassembly Flow ........................................................... 73-2. Case ................................................................................. 83-3. Back Panel ....................................................................... 83-4. DVD Section ................................................................... 93-5. Main Board ...................................................................... 103-6. Front Panel ...................................................................... 103-7. Front Amp Boardm Sur Amp Board ................................ 113-8. Tape Mechanism Deck .................................................... 123-9. Panel Board ..................................................................... 123-10. Video Board ..................................................................... 133-11. DMB07 Board, DVD Mechanism Deck

(CDM81A-DVBU60) ...................................................... 133-12. Tray .................................................................................. 143-13. Motor Board, M761 (LD/ST Motor),

M762 (BU U/D Motor) ................................................... 143-14. Base Unit (DVBU60) ...................................................... 153-15. RF Board ......................................................................... 153-16. Optical Pick-Up (DBU-3) ............................................... 16

4. TEST MODE .............................................................. 17

5. MECHANICAL ADJUSTMENTS ....................... 19

6. ELECTRICAL ADJUSTMENTSDeck section .................................................................... 26Video Section .................................................................. 27

7. DIAGRAMS7-1. Circuit Board Location .................................................... 297-2. Block Diagram – DVD DSP (1/2) Section – .................. 317-3. Block Diagram – DVD DSP (2/2) Section – .................. 327-4. Block Diagram – Tuner/Tape Deck Section – ................ 337-5. Block Diagram – Main Section – ................................... 347-6. Block Diagram – Amp Section – .................................... 35

7-7. Printed Wiring Board – RF Board – ............................... 367-8. Schematic Diagram – RF Board – .................................. 377-9. Printed Wiring Board – DVD Mechanism Board – ....... 387-10. Schematic Diagram – DVD Mechanism Board – .......... 397-11. Printed Wiring Board – DMB07 Board (Side A) – ........ 407-12. Printed Wiring Board – DMB07 Board (Side B) – ........ 417-13. Schematic Diagram – DMB07 Board (1/6) – ................. 427-14. Schematic Diagram – DMB07 Board (2/6) – ................. 437-15. Schematic Diagram – DMB07 Board (3/6) – ................. 447-16. Schematic Diagram – DMB07 Board (4/6) – ................. 457-17. Schematic Diagram – DMB07 Board (5/6) – ................. 467-18. Schematic Diagram – DMB07 Board (6/6) – ................. 477-19. Printed Wiring Board – Video Board – .......................... 487-20. Schematic Diagram – Video Board – ............................. 497-21. Printed Wiring Boards – Main Board – .......................... 507-22. Schematic Diagram – Main Board (1/3) – ..................... 517-23. Schematic Diagram – Main Board (2/3) – ..................... 527-24. Schematic Diagram – Main Board (3/3) – ..................... 537-25. Printed Wiring Boards – Panel Board – ......................... 547-26. Schematic Diagram – Panel Board – ............................... 557-27. Printed Wiring Board – Disc SW, Vol, HP Board – ....... 567-28. Schematic Diagram – Disc SW, Vol, HP Board – .......... 577-29. Printed Wiring Board – Front Amp Board – .................. 587-30. Schematic Diagram – Front Amp Board – ..................... 597-31. Printed Wiring Board – SURAmp Board – .................... 607-32. Schematic Diagram – SUR Amp Board – ...................... 617-33. IC Block Diagram ........................................................... 638. EXPLODED VIEWS8-1. Case, Rear Panel Section ................................................. 788-2. Front Panel Section ......................................................... 798-3. Chassis Section ................................................................ 808-4. DVD Mechanism Deck Section-1

(CDM81A-DVBU60) ..................................................... 818-5. DVD Mechanism Deck Section-2

(CDM81A-DVBU60) ..................................................... 828-6. DVD Mechanism Deck Section-3

(CDM81A-DVBU60) ..................................................... 838-7. Base Unit (DVBU60) ...................................................... 84

9. ELECTRICAL PARTS LIST ................................ 85

4

HCD-NXM4DSECTION 1

SERVICING NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observefrom more than 30 cm away from the objective lens.

LASER DIODE AND FOCUS SEARCH OPERATION CHECK

Carry out the “S curve check” in “CD section adjustment” and checkthat the S curve waveform is output several times.

• SERVICE POSITION FOR TAPE MECHANISM DECK

tape mechanism deck

Jig (J-2501-271-A)

Jig (J-2501-270-A)

CN301

CN302

• NOTE ON CD/DVD MECHANISM DECK EXCHANGEIf CD/DVD mechanism deck is exchanged while the desk had gone into trays 2 or 3, since the address is memorized by the microprocessor,the set will not operate normally.In this case, please perform cold reset with reference to test mode (page 17.)

• AbbreviationE2 : 120 V AC Area in E modelE3 : 240 V AC Area in E modelE15 : Iran modelEA : Saudi Arabia modelSP : Singapore modelMY : Malaysia modelAUS : Australian modelTH : Thai model

• MODEL IDENTIFICATION– Back Panel –

MODEL PART No.

SP, MY models 4-253-361-0[]

E2 model 4-253-361-1[]

E3, E15 model 4-253-361-2[]

EA model 4-253-361-3[]

AUS model 4-253-361-4[]

TH model 4-253-361-5[]

PART No.

5

HCD-NXM4DSECTION 2GENERAL This section is extracted

from instruction manual.

LOCATING THE CONTROLS

Main unit

ALBUM +/– qaCD SYNC wgDeck A w;Deck B qgDIMMER whDISC 1 – 5 3Disc tray 9DISPLAY wjDisplay window 4DSGX qsDVD eaDVD MENU qaDVD TOP MENU qa

ECHO LEVEL qjMIC1/MIC2 jacks qhMIC LEVEL qkPHONES jack qlRemote sensor 2SOUND MODE control wd

SOUND SELECT control ws

TAPE A/B wlTUNER/BAND e;TUNING +/– 0VIDEO/SAT wkVOLUME control qd

?/1 (power) 1nN (play) 5X (pause) 6x (stop) 7DVD Z (open/close) 8.m/M> (rewind/fast

forward, go back/go forward) 0TAPE Z B (eject) qfA TA PE Z (eject) waz START (record) wf

List of button locations and reference pages

ALPHA BETICAL ORDER

A – D E – Z

BUTTON DESCRIPTIONS

1 2 3 4

56789

0

qa

qs

qd

qf

e;ea

wlwk

wjwhwgwfwdws

wa

w; qg

qhqjqkql

6

HCD-NXM4DThis section is extractedfrom instruction manual.

Remote control

ALBUM + 7ALBUM – qaANGLE qkAUDIO qkBAND wgCLEAR wlCLOCK/TIMER SELECT e;

CLOCK/TIMER SET e;

DISC SKIP wfDISPLAY waDVD DISPLAY wh

DVD MENU 7DVD SETUP ws

DVD TOP MENU qaENTER wj

FM MODE 5FUNCTION +/– 0

KARAOKE/MPX qfNumber buttons qdPLAY MODE 4

REPEAT 5SLEEP qhSOUND FIELD +/– wdSUBTITLE qkTUNER MEMORY 3TUNING MODE 4TUNING +/– wkTV CH +/– qgTV/VIDEO eaTV VOL +/– 2VOLUME +/– 8

?/1 (power) 1nN (play) 6X (pause) 6x (stop) 6KEY CONTROL #/29>10 qsTV ?/1 qjO RETURN qlm (rewind) w;M (fast forward) w;SLOW /y w;

M/m/</, wj

. (go back) wk> (go forward) wk

ALPHABETICA L ORDER

A – E F – Z

BUTTON DESCRIPTIONS

O

bB

V

v

+

+

–

– +–

+–

+

–

+

–

+

–

+

–

XbB

yy +– yy

x

m M. >

O

bB

V

v

+–

+

–

+

–

+

–

+

–

XbB x

m M. >

ws

1

wk

qa

wd

2qg

qh

qf

qs

qd

3

4

5

6

7

8

90

qj

qk

w;

wa

ql

e;

ea

wl

wf

wgwhwj

7

HCD-NXM4DSECTION 3

DISASSEMBLY

• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

3-2.CASE(Page 8)

3-3.BACK PANEL(Page 8)

3-7.FRONT AMP BOARD, SUR AMP BOARD (Page 11)

3-11. DMB07 BOARD,DVD MECHANISM DECK(CDM81A-DVBU60)(Page 13)

3-10.VIDEO BOARD (Page 13)

3-6.FRONT PANEL (Page 10)

3-9.PANEL BOARD (Page 12)

3-12. TRAY(Page 14)

3-14. BASE UNIT (DVBU60)(Page 15)

3-16. OPTICAL PIC-UP (DBU-3)(Page 16)

3-15. RF BOARD(Page 15)

3-8.TAPE MECHANISM DECK (Page 12)

3-4.DVD SECTION (Page 9)

3-13. MOTOR BOARD,M761 (LD/ST MOTOR),M762 (BU U/D MOTOR)(Page 14)

SET

3-5.MAIN BOARD(Page 10)

8

HCD-NXM4D

Note: Follow the disassembly procedure in the numerical order given.

3-2. CASE

3-3. BACK PANEL

1 three screws (CASE 3 TP2)

2 three screws (CASE 3 TP2)

3 two screws (sumitite (B3))


5 screw (sumitite (B3))

6

7 CASE

1 screw (+BVTP 3X8)

2 two screws (+BVTP 3X8)

3 four screws (+BVTP 3X8)



6 back panel section

7 CNP204

8 connector (CN506)

9

HCD-NXM4D

3-4. DVD SECTION

1 CNP200

2 CNP2023 CNP372

6 DVD section

7 connector (CN102)

4 screw (+BVTP 3X8)


10

HCD-NXM4D

3-5. MAIN BOARD


2 connector (CN102)

3 connector (CN103)

4 MAIN board

5 CNP303

6 connector (CN108)

7 connector (CN301)

8 connector (CN302)

0 connector (CN101)

qa CNP112

qs CNP110qd CNP109

9 connector (CN102)

3-6. FRONT PANEL


2 front panel section

3 connector (CN505)

11

HCD-NXM4D

3-7. FRONT AMP BOARD, SUR AMP BOARD



3 FRONT AMP board

4 connector (CN502)

qa screw (+BVTP 3X8)

qs screw (+BVTP 3X8)

qd two screws (+BVTP 3X8)

qf bracket

qg two screws (+BVTP 3X8)

qh bracket

8 SUR AMP board

5 screw (+BVTP 3X8)


7 screw (+BVTP 3X8)

9 connector (CN503)

q; connector (CN507)

12

HCD-NXM4D

3-8. TAPE MECHANISM DECK

3-9. PANEL BOARD

1 four screws (+BVTP 2.6X8)

2 screw (+BVTP 2.6X8)


4 bracket (main)


6 three screws (+BVTP 2.6X8)

7 PANEL board

1

2

3 two screws (+P 2.6X3)

4 two screws (+BVTP 2.6X8)

5 tape mechanism deck

13

HCD-NXM4D

3-10. VIDEO BOARD

3-11. DMB07 BOARD, DVD MECHANISM DECK (CDM81A-DVBU60)

1 CNP1101

2 screw (+BVTP 3X8)

3 screw (+BVTP 3X8)

4 VIDEO board

1 CNP501

2 CNP105 3 CNP107


5 screw (+BVTP 3X8)

6 screw (+BVTP 3X8)

7 DMB07 board


9 screw (+BVTP 3X8)0 screw

(+BVTP 3X8)

qa screw (+BVTP 3X8)

qs DVD mechanism deck (CDM81A-DVBU60)

14

HCD-NXM4D

3-12. TRAY

1 two screws (+BTP 2.6X8)

2 two screws (+BTP 2.6X8)

3 bracket

4

5 tray

3-13. MOTOR BOARD, M761 (LD/ST MOTOR), M762 (BU U/D MOTOR)

1 screw (+BTP 2.6X8)

2 bracket


4 MOTOR board

5 Remove soldering from the two points.

6 M761 (LD/ST MOTOR)

7 Remove soldering from the two points.

8 M762 (BU U/D MOTOR)

15

HCD-NXM4D

3-14. BASE UNIT (DVBU60)

3-15. RF BOARD

1 two floating screws (+PTPWH2.6)

2 base unit (DVBU60)



4 CNP101

3 RF board

16

HCD-NXM4D

3-16. OPTICAL PICK-UP (DBU-3)

1 screw (+BTP 2.6X8)2 two screws

(+BTP 2.6X8)

3 holder (DBU1) assy

4 step screw

5 step screw

6 step screw

8 optical pick-up (DBU-3)

7 9 insulator

0 insulator

qa insulator

17

HCD-NXM4DSECTION 4TEST MODE

[Change-over of AM Tuner Step between 9 kHz and 10 kHz]• A step of AM channels can be changed over between 9 kHz

and 10 kHz.

Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “TUNER”, and press [TUNER/BAND]

button to select the BAND “AM”.

3. Press ?/1 button to turn the set OFF.

4. Press x button continuously, then press ?/1 button. Theset will POWER on automatically, and the display offluorescent indicator tube changes to “AM 9 kHz step” or “AM10 kHz step”, and thus the channel step is changed over.

[Cold Reset]• The cold reset clears all data including preset data stored in

the RAM to initial conditions. Execute this mode whenreturning the set to the customer.

Procedure: 1. Press x button continuously, then press [DIMMER]

and ?/1 buttons.

[Switching MD/VIDEO Functions]

Procedure:1. Press the ?/1 button to turn the set ON.

2. Press the ?/1 button while holding the VIDEO/SAT buttondepressed to toggle between “SAT” and “VIDEO.” Theselected mode is displayed.

[Aging Mode]This mode can be used for operation check Tape deck section.

• If an error occurred:The aging operation stops and is displayed status.

• If no error occurs:The aging operation continues repeatedly

Aging mode in Tape Deck section

Procedure:1. Load the tapes into the decks A and B respectively.

2. Press ?/1 button on the set ON3. Select the function “TAPE A”

4. Press x button continuously, then press X and [TAPE A/B]

buttons. and aging mode is started.5. To exit from the aging mode perform [Cold Reset].

• In the aging mode ,the program is executed in the followingsequence.

Step Operation Display

1 Rewind the TAPE A TAPE A AG-1

2 Rewind the TAPE B TAPE B AG-1

3 Play the TAPE A (t) (2 minute) TAPE A AG-2

4 F•F. (AMS) the TAPE A TAPE A AG-3

5 Play the TAPE A (T) (2 minute) TAPE A AG-4

6 Rewind the TAPE A TAPE A AG-5

7 Play the TAPE B (t) (2 minute) TAPE B AG-2

8 F•F.(AMS) the TAPE B TAPE B AG-3

9 Play the TAPE B (T) (2 minute) TAPE B AG-4

10 Rewind the TAPE B TAPE B AG-5

[GC Test Mode]• All fluorecent segments and LEDs are tested.• Microprocessor virsion.• Keyboard and jog check.• Display check.

Procedure: 1. To enter the test mode, press x button coutinuously, then

press X and [TUNER/BAND] buttons.2. All segments and LEDs (without STANDBY LED) are turned

on.3. Press the [TUNING -] button to increment the microprocessor

software version.4. Press the [TUNING -] button to change the indication for the

microprocessor software version. 3. Press the b B button to set the check mode for the entries

(KEY, JOG, etc.). 4. Press the X button to display the current VACS level.

7. Press the x button to enter the mode to check the display. Ifyou press this button repeatedly, the display will changesequentially as the button is pressed.

8. Press x button coutinuously, then press X and [TUNER/BAND]

buttons.

[MC Test Mode] (Amplifier SECTION)• This mode is used to test the function of the amplifier section.

Procedure:1. Press ?/1 button to turn the set ON.

2. To enter the test mode, press x button coutinuously, then press X and z START buttons.

3. Turn [VOLUME] knob to counter-clockwise, the function ofthe equalizer is set to “MIN”.

4. Turn [VOLUME] knob to clockwise, the function of theequalizer is set to “MAX”.

5. Whenever turn [SOUND MODE] knob to clockwise, the displayswitches as follows.

“TONE MAX” t“TONE MIN” t“TONE FLAT”6. Press [DSGX] button to select DBFB ON or OFF.

7. To exit from this mode, press ?/1 button to turn the setOFF.

8. Press ?/1 button to turn the set ON.


10. Select SOUND FIELD mode by turn the SOUND MODEknob.

11. Change the speaker output by turn the SOUND SELECT knob.

[MC Test Mode] (Tape section)• This mode is used to test the functions of the Tape Section.

Procedure:1. Press ?/1 button to turn the set ON.


3. While holding the [DIMMER] button depressed, turn the ALCON.

4. Press the z START button to start REC (recording).5. While recording, press the [TUNING +] button to perform

automatic rewind and automatic playback (for FF version).Also, press the [TUNING -] button to perform automatic rewindand automatic playback (for FR version).

6. Select the function “TAPE A” or “TAPE B”

18

HCD-NXM4D

7. Press the [CD SYNC] button while “TAPE A” or “TAPE B”is selected, to perform AMS check. “EDG[ ]” is displayed.A number appears inside[ ].

8. To exit from this mode, press ^/1 button to turn the set OFF.

[DVD Ship Mode (LOCK) ]• This mode moves the pick-up to the position durable to

vibration. Use this mode when returning the set to the customerafter repair.

Procedure:

1. Press ^/1 button to turn the set ON.2. Select the function “DVD”.

3. Press x button and [DVD] button simultaneously.4. The “STANDBY” display blinks instantaneously, and the DVD

ship mode is set.5. To fluorescent indicator tube displays ‘‘LOCK’’.

[DVD Ship (LOCK) & COLD RESET MODE]

Procedure:


3 Press x button continuously, then press X and VIDEO/SATbuttons.

4. The “STANDBY” display blinks instantaneously and DVDship mode is set.

5. To fluorescent indicator tube displays “LOCK” and the set isreset.

[DVD power -manage function]• This mode let you switch on or off power supply to the BU

during TUNER function.• When DVD POWER is set to OFF, the power supply to the

BU is cut off during TUNER function. It will increase thetime taken to access DVD when function change from TUNERto DVD but it will improve tuner reception.

• When DVD POWER is set to ON, the power supply to theBU is not cut off during TUNER function. It will reduce thetime taken to access DVD when function change from TUNERto DVD but it will decrease tuner reception performance.

Procedure:

1. Press ^/1 button to the set ON.2. Select the function “DVD”.

3. Press ^/1 button to turn the set OFF.

4. Press x button continuously, then press /1 button.The setwill POWER on automatically, and the display of fluorescentindicator tube changes “DVD POWER OFF” or “DVDPOWER ON”.


[DISC Tray Lock]

Procedure:

1. Press ^/1 button to the set ON.2. Select the function “DVD”.

3. Press x button continuously, then press DVD Z button for5 seconds.And the displays of fluorescent indicator tube changes to“LOCKED” or “UNIOCKED”.


[DVD Repeat 5 Times Limit Release Mode]

Procedure:


3. Press x button continuously, then press [CD SYNC]

button.4. The message “LIMIT OFF” is displayed.

5. Press ^/1 button to the set OFF.

19

HCD-NXM4D

[GENERAL DESCRIPTION]The Test Mode allows you to make diagnosis and adjustment easilyusing the remote commander and monitor TV. The instructions,diagnostic results, etc. are given on the on-screen display (OSD).

[STARTING TEST MODE]1. Press the +/1 button to turn the power on, and set the function

to DVD.2. While pressing the x and Z button, turn the [VOLUME]

knob clockwise to enter the test mode.3. It displays “SERVICE IN” on the liquid crystal display, and

displays the Test Mode Menu on the monitor screen as follows.(At the bottom of the menu screen, the model name andrevision number are displayed)

Test Mode Menu

0. Syscon Diagnosis1. Drive Auto Adjustment2. Drive Manual Operation3. Mecha Aging4. Emergency History5. Mecha Error History6. Version Information7. Video Level Adjustment

Exit: POWER KeyModel :DHC-NXMxxRevision :x.xx

4. To execute each function, select the desired menu and pressits number on the remote commander.

5. To release from test mode, press the +/1 button and turn thepower off.

[OPERATING TEST MODE]0. SYSCON DIAGNOSISThe same contents as board detail check by serial interface can bechecked from the remote commander operation.On the Test Mode Menu screen, press [10/0] key on the remotecommander, and the following Check Menu will be displayed.

### Syscon Diagnosis ###

Check Menu0. Quit1. All2. Version3. EEPROM4. GPIO5. SD Bus6. Video

0-0. QuitQuit the Syscon Diagnosis and return to the Test Mode Menu.

0-1. All (All items continuous check)This menu checks all diagnostic items continuously. Normally, allitems are checked successively one after another automaticallyunless an error is found, but at a certain item that requires judgmentthrough a visual check to the result, the following screen is displayedfor the key entry.

• Example display

### Syscon Diagnosis ###

Diag All CheckNo.2 Version

2-3. ROM Check SumCheck Sum = xxxx

Press NEXT Key to ContinuePress PREV Key to Repeat

For the ROM Check, the check sum calculated by the Syscon isoutput, and therefore you must compare it with the specified valuefor confirmation.Following the message, press the [NEXT ] button to go to thenext item, or press the [ PREV] button to repeat the sameoperation again.To quit the diagnosis and return to Check Menu screen, press the[RETURN] key on the remote commander to display Check Menu.

• Error occurredIf an error occurred, the diagnosis is suspended and error is displayed.Press the [RETURN] key on the remote commander to quit thediagnosis, or press the [ PREV] button to repeat the same checkwhere an error occurred, or press the [NEXT ] button to continuethe check from the item next to faulty item.

General Description of Checking MethodSelecting 2 and subsequent items calls the submenu screen of eachitem. And selecting 2 and subsequent items executes respectivemenus and outputs the results.For the contents of each submenu, see “Check Items List” as below.

Check Items List:0-2. Version

0-2-1. All0-2-2. Revision0-2-3. ROM Check Sum0-2-4. Model Type0-2-5. Region

0-3. EEPROM Check0-3-1. Sampling Check0-3-2. Detail Check

0-4. GP I/O Check0-5. SD Bus Check0-6. Video Check

0-2. Version0-2-2. Revision

The revision number of ROM (IC206) that the programfor the DVD system processor (IC207) is stored.

0-2-3. ROM Check SumCheck sum is calculated.(4 digits hexadecimal number)

0-2-4. Model TypeModel name is displayed. (DHC-NXMXX)

>

.

>

.

DVD OSD Test Mode

20

HCD-NXM4D

0-2-5. RegionModel destination code is displayed. (2 digits number)

0-3. EEPROM Check0-3-1. Sampling Check

EEPROM check at every 64 words.It compares read data with write data of each address.When there are discrepancies between two data, it displayserror.

0-3-2. Detail CheckEEPROM check at every 1 word.It compares read data with write data of each address.When there are discrepancies between two data, it displayserror.

0-4. GP I/O CheckPull up/down setting check of the DVD system processor (IC207)pin 150, 151 and 154 (for clock setting port).

0-5. SD Bus CheckSD bus data check between DVD decoder (IC701) and D-RAM(IC706).

0-6. Video CheckOutput the color bars for video level adjustment.

1. DRIVE AUTO ADJUSTMENTOn the Test Mode Menu screen, press the [1] key on the remotecommander, and the Adjustment Menu will be displayed.

•Use DVD reference disc unless othermise indicated.[DVD reference disc]

• LUV-P01 (4-999-032-01) (CD)•TDV-540C (J-2501-235-A) (DVD-DL)• TDV-520CSO (J-2501-236-A) (DVD-SL)

## Drive Auto Adjustment ##Adjustment Menu

0. ALL 1. DVD-SL 2. CD 3. DVD-DL

Exit: RETURN

Normally, [10/0] is selected to adjust DVD (single layer), CD andDVD (dual layer) in this order. But, individual items can be adjustedfor the case where adjustment is suspended due to an error. In thismode, the adjustment can be made easily through the operationfollowing the message displayed on the screen.The disc used for adjustment must be the one specified foradjustment.

1-0. ALLPress the [10/0] key on the remote commander, and the servo setdata in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CDdisc and 3. DVD-DL disc are adjusted in this order.Each time one disc was adjusted, it is ejected. Replace it with thespecified disc following the message. You can finish the adjustmentby pressing the [RETURN] button on the remote commander.

Note: During adjustment of each disc, the measurement for disc type judg-ment is made. As automatic adjustment does not judge the disctype unlike conventional models, take care not to insert wrong typediscs. Also, do not give a shock during adjustment.

1-1. DVD-SL (single layer)Press the [1] key on the remote commander and insert a DVD singlelayer disc following the message. Then the adjustment will be madethrough the steps below, then adjusted values will be written to theEEPROM.

DVD Single Layer Disc Adjustment Steps:1. Sled reset2. Disc check memory SL3. Wait 300 msec4. Set disc type SL5. LD on6. Spindle start7. Wait 1 sec8. Focus servo on 09. Auto track offset adjust10. CLVA on11. Wait 500 msec12. Tracking on13. Wait 1 sec14. Sled on15. Check CLV on16. Auto focus offset adjust17. Auto focus gain adjust18. Auto focus offset adjust19. EQ boost adjust20. Auto track gain adjust21. All servo stop22. EEP copy loop filter offset

1-2. CDPress the [2] key on the remote commander and insert a CD discfollowing the message. Then the adjustment will be made throughthe steps below, then adjusted values will be written to the EEPROM.

CD Adjustment Steps1. Sled tilt rest2. Disc check memory CD3. Wait 500 msec4. Set disc type CD5. LD on6. Spindle start7. Wait 500 msec8. Focus servo on 09. Auto track offset adjust10. CLVA on11. Wait 500 msec12. Tracking on13. (TC display start)14. Wait 1 sec15. Sled ON16. Check CLV on17. Auto focus offset adjust18. Auto focus gain adjust19. Auto focus offset adjust20. EQ boost adjust21. Auto track gain adjust22. All servo stop

21

HCD-NXM4D

In using the manual operation menu, take care of the followingpoints. These commands do not provide protection, thus requiringcorrect operation. The sector address or time code field is displayedwhen a disc is loaded.

Note:1. Set correctly the disc type to be used on the Disc Type

screen.2. In case of an alarm, immediately press the x button to

stop the servo operation, and press the +/1 button toturn the power off.

Basic operation:(controllable from front panel or remote commander) +/1 : Power OFF (release the Test Mode) x : Servo stop Z : Stop and eject/Loading[RETURN] : Return to Operation Menu or Test

Mode Menu[ PREV], [NEXT ] : Transition between sub modes of menu[1] to [9], [10/0] : Selection of menu itemsCursor o / O : Increase/Decrease in manually

adjusted value

2-1. Disc Type

Disc Type

Disc Type Select

1. Disc Type Auto Check 2. Set Disc Type DVD 3. Set Disc Type CD 4. Set Disc Type Hybrid

Exit: RETURN

2-1-1. Disc Type Auto Check1) Press the [1] key on the remote commander to display the Disc

Type Auto Check screen.2) Insert a disc and press the [ENTER] key on the remote

commander.3) It judges the type of inserted disc automatically and displays

the disc type and so on as below.

Disc Type Auto Check

Disc Type xx Layer xx Mirr Time xx Mirr Count xx FZC Count xx PI Reference xx PI Peak xx

ENTER.Execute

Exit: RETURN

Disc Type : CD, DVD or Hybrid (SACD)Layer : SINGLE, DUAL or HYBRIDMirr Time : Mirror time of between disc surface and record

surface when disc type judgment. (hexadecimal number)

1-3. DVD-DL (dual layer)Press the [3] key on the remote commander and insert a DVD duallayer disc following the message. Then the adjustment will be madethrough the steps below, then adjusted values will be written to theEEPROM.

DVD Dual Layer Disc Adjustment Steps:1. Sled tilt reset2. Disc check memory DL3. Wait 500 msec4. Set disc type DL5. LD on6. Spindle start7. Wait 1 sec

Layer 1 Adjust8. Focus servo on 09. Auto track offset adjust10. CLVA on11. Wait 500 msec12. Tracking on13. Wait 500 msec14. Sled on15. Check CLV lock16. Auto loop filter offset adjust, Auto focus adjust17. Auto focus gain adjust18. Auto focus offset adjust19. EQ boost adjust20. Auto loop filter offset adjust21. Auto Track Gain Adjust

Layer 0 Adjust22. Focus jump (L1 t L0)23. Auto track offset adjust L024. CLVA on25. Wait 500 msec26. Tracking on27. Wait 500 msec28. Sled on29. Check CLV lock30. Auto Focus Adjust31. Auto focus gain adjust32. Auto focus offset adjust33. EQ boost adjust34. Auto track gain adjust35. All servo stop

2. DRIVE MANUAL OPERATIONNote: This mode is used for design, and not used in service fundamen-

tally.

On the Test Mode Menu screen, press the [2] key on the remotecommander, and the Operation Menu will be displayed. For themanual operation, each servo on/off control and adjustment can beexecuted manually.

## Drive Manual Operation ##Operation Menu

1. Disc Type 2. Servo Control 3. Track/Layer Jump 4. Non EEPROM Write Adjust 5. EEPROM Write Adjust 6. Memory Check 7. Disc Check Memory 8. Error Rate Display 9. SACD Water Mark

Exit: RETURN

>.

22

HCD-NXM4D

Mirr Count : The number of times which mirror counts between disc surface and record surface when disc type judging.

FZC Count : The number of times which focus zero cross points of each layer when lens down.

PI Reference : The average of PI reference voltage. (hexadecimal number)

PI Peak : PI peak level voltage. It performs only when disc type judgment is successful. (hexadecimal number)

2-1-2. Disc Type DVDIt sets up so that it may judge as a disc type of specification of thedisc with which the set was inserted.

[1]: DVD single layer disc (12 cm)[2]: DVD dual layer disc (0 layer, 12 cm)[3]: DVD dual layer disc (1 layer, 12 cm)[4]: DVD-RW disc (12 cm)[5]: DVD single layer disc (8 cm)[6]: DVD dual layer disc (0 layer, 8 cm)[7]: DVD dual layer disc (1 layer, 8 cm)[8]: DVD-RW disc (8 cm)

2-1-3. Disc Type CDIt sets up so that it may judge as a disc type of specification of thedisc with which the set was inserted.

[1]: CD disc (normal speed, 12 cm)[2]: CD disc (double speed, 12 cm)[3]: CD disc (normal speed, 8 cm)[4]: CD disc (double speed, 8 cm)[5]: CD-RW disc (normal speed, 12 cm)[6]: CD-RW disc (double speed, 12 cm)[7]: CD-RW disc (normal speed, 8 cm)[8]: CD-RW disc (double speed, 8 cm)

2-1-4. Disc Type HybridIt sets up so that it may judge as a disc type of specification of thedisc with which the set was inserted.

[1]: SACD Hybrid disc (SACD layer, 12 cm)[2]: SACD Hybrid disc (CD layer, normal speed, 12 cm)[3]: SACD Hybrid disc (CD layer, double speed, 12 cm)[4]: SACD Hybrid disc (SACD layer, 8 cm)[5]: SACD Hybrid disc (CD layer, normal speed, 8 cm)[6]: SACD Hybrid disc (CD layer, double speed, 8 cm)

2-2. Servo ControlNote: Be sure to perform the disc type setup before performing this item.

Servo Control 1.LD off R.Sled FWD 2.Focus off L.Sled REV 3.SPDL off U.Sled Reset 4.CLVA off D.Sled Limit 5.Trk. off 6.Sled off 7.Fcs.Srch off

0.All Servo Off

Exit: RETURN

On this screen, the servo on/off control necessary for replay isexecuted. Normally, turn on each servo from 1 sequentially andwhen CLVA is turned on, the usual trace mode becomes active. Inthe trace mode, DVD sector address or CD time code is displayed.This is not displayed where the spindle is not locked.The spindle could run overriding the control if the spindle system isfaulty or RF is not present. In such a case, do not operate CLVA.

[1] LD : Turn on/off the laser.[2] Focus : Search the focus and turn on the focus.[3] SPDL : Turn on/off the spindle.[4] CLVA : Turn on/off normal servo of spindle servo.[5] Trk. : Turn on/off the tracking servo.[6] Sled : Turn on/off the sled servo.[7] FCS. Srch : Turn on/off the focus search.[10/1] : All servo off.[R] Sled FWD (right cursor) : Move the sled forward.[L] Sled REV (left cursor) : Move the sled reverse.[U] Sled FWD (up cursor) : Reset the sled.[D] Sled REV (down cursor) : Limit in the sled.

2-3. Track/Layer Jump

Track/Layer Jump 1. 1Tj FWD 2. 1Tj REV 3.500Tj Fine FWD 4.500Tj Fine REV 5.10kTj Dirc FWD 6.10kTj Dirc REV 7.20kTj Dirc FWD 8.20kTj Dirc REV

0. All Servo Off

Exit: RETURN

On this screen, track jump, etc. can be performed. Only for the DVDdual layer disc, the focus jump and layer jump are displayed in theright field

[1] 1Tj FWD : 1 track jump forward.[2] 1Tj REV : 1 track jump reverse.[3] 500Tj FWD : 500 track jump (fine search)forward.[4] 500Tj REV : 500 track jump (fine search) reverse.[5] 10kTj FWD : 10k track jump (direct search) forward.[6] 10kTj REV : 10k track jump (direct search) reverse.[7] 20kTj FWD : 20k track jump (direct search) forward.[8] 20kTj REV : 20k track jump (direct search) reverse.[10/0] : All servo off.

2-4. Non EEPROM Write Adjust

Non EEPROM Write Adjust

1. Focus Offset 2. Focus Gain 3. Trk. Offset Coarse 4. Trk. Offset Fine 5. Trk. Gain 6. EQ Boost

0.All Servo Off

Exit: RETURN

On this screen, each item can be adjusted manually. Select the desirednumber [1] to [10/0] from the remote commander, and current setting forthe selected item will be displayed, then increase or decrease numericvalue with the O key or o key. If CLV has been applied, the jitter isdisplayed for reference for the adjustment.

23

HCD-NXM4D

[1] Focus Offset : Adjusts focus offset.[2] Focus Gain : Adjusts focus gain.[3] TRK. Offset coares :

Adjusts tracking offset of the RF amp (IC001) side.

[4] TRK. Offset fine : Adjusts tracking offset of the DSP (IC401) side.

[5] TRK. Gain : Adjusts track gain.[6] EQ Boost : Adjusts amount of boost of equalizer.[10/0] : All servo off.

2-5. EEPROM Write Adjust

EEPROM Write Adjust

1. Focus Offset 2. Focus Gain 3. Trk. Offset Coarse 4. —————— 5. Trk. Gain 6. EQ Boost

0.All Servo Off

Exit: RETURN

On this screen, each item can be adjusted automatically. Select thedesired number [1] to [10/0] from the remote commander, andselected item is adjusted automatically.

[1] Focus Offset : Adjusts focus offset.[2] Focus Gain : Adjusts focus gain.[3] TRK. Offset coarse :

Adjusts tracking offset of the RF amp (IC001) side.

[5] TRK. Gain : Adjusts track gain.[6] EQ Boost : Adjusts amount of boost of equalizer.[10/0] : All servo off.

2-6. Memory CheckDisplay images are shown as follows, and all two screens are ableto switch by the O key (UP) or o key (DW).

EEPROM Data 1/2 CD SL L0 L1Focus Gain xx xx xx xxTrk. Gain xx xx xx xxFocus Offset xx xx xx xxTrk. Offset xx xx xx xxEQ. Boost xx xx xx xxPI Level xx xx -- --Fcs. Balance -- xx -- --Jitter xx xx xx xxMirror Time xx xx xx --FE Level -- xx -- --Traverse Lv1. -- xx -- --Next:DW Default:CLR Exit:RET

EEPROM Data 2/2 CDRW DVDRWFocus Gain xx xxTrk. Gain xx xxFocus Offset xx xxTrk. Offset xx xxEQ. Boost xx xx

Prev:UP Default:CLR Exit:RET

On this screen, current servo adjusted data stored in the EEPROMare displayed. The adjusted data are initialized by pressing the[CLEAR] key, but be careful that they are not recoverable afterinitialization.Before clearing the adjusted data, make a note of the set data. Thisscreen will also appear if [0]-All is selected in the Drive AutoAdjustment. In this case, default setting cannot be made.

2-7. Disc Check Memory

Disc Check Memory

1. SL Disc check 2. CD Disc check 3. DL Disc check

Exit: RETURN

On this screen, measure the mirror time of chucked disc, and writeto the EEPROM.

2-8. Error Rate Display

Error Rate DisplayUC CR Address

PI1 Err Now xx xxxx xxxxxxxxMax xx xxxx xxxxxxxxAvg xx xxxx

PI2 Err Now xx xxxx xxxxxxxxMax xx xxxx xxxxxxxxAvg xx xxxx

PO Err Now xx xxxx xxxxxxxxMax xx xxxx xxxxxxxxAvg xx xxxx

START: ENTER STOP: RETURN

On this screen, measure and display the error rate.

UC : Incorrect valueCR : Correct valueAdd : Address

24

HCD-NXM4D

2-9. SACD Water Mark Check (Not used)

SACD Water Mark Check

PSP AMP PSN

Adjust Error Failed Start: ENTER Stop: RETURN

On this screen, measure the PSP AMP value and PSN value of SACDwater mark.

3. MECHA AGINGOn the Test Mode Menu screen, selecting [3] executes the aging ofthe mechanism deck.

## Aging Test MENU ##

** Pls use over 40min. CD **Operation Menu

1. Open/Close Test

Exit: RETURN

1) On the Aging Test MENU screen, press the [1] key on theremote commander to display the Open/Close Test screen.

2) Insert discs and press the [ENTER] key on the remotecommander.

3) Is starts the aging.During aging, the disc number, operating status and repeatcycle are displayed. Aging can be aborted at any time bypressing the [RETURN] key. After the operation is stopped,press the [RETURN] key to return to the Aging Test MENU.

4. EMERGENCY HISTORYOn the Test Mode Menu screen, selecting [4] displays theinformation such as servo emergency history.The history information from last 1 up to 10 can be scrolled withthe O key or o key. Also, specific information can be displayedby directly entering that number with ten keys.

### EMG. History ###

Laser Hours CD xxxxhxxmDVD xxxxhxxm

a. bb xx xx xx xx xx xx xxxx xx xx xx xx xx xx xx

a. bb xx xx xx xx xx xx xxxx xx xx xx xx xx xx xx

Select:1-9 Scroll:UP/DOWN (1.Latest EMG.) Exit: RETURN

xxxxhxxm : The laser on total hours. Data below minutes are omitted.

a. : Error number.bb : Error code.xx : Not used.

• Clearing History InformationClearing laser hours:

Press the [DVD DISPLAY] and [CLEAR] keys in this order.Then both CD and DVD data are cleared.

Clearing emergency history:Press the [DVD TOP MENU] and [CLEAR] keys in this order.

Initializing set up data:Press [DVD MENU] and [CLEAR] keys in this order.The data have been initialized when “EEPROM InitializeFinished” message is displayed.• Code list of Emergency History

10 : Communication to RF AMP (IC001) failed.11 : Each servo for focus, tracking, and spindle is unlocked.12 : Check sum error of EEPROM (IC204).14 : Communication to servo DSP (IC509) failed, or servo

DSP (IC509) is faulty.15 : Communication to DVD decoder (IC701) failed, or DVD

decoder (IC701) is faulty.16 : Communication to DSD decoder (IC801) failed, or DSD

decoder (IC801) is faulty. (Not used)20 : Initialization of sled servo failed. It is not placed in the

initial position.23 : Sled servo operation error.24 : Made a request to move the sled servo to wrong position.30 : Tracking balance adjustment error.31 : Tracking gain adjustment error.33 : Focus bias adjustment error.34 : Focus gain adjustment error.35 : Equalizer adjustment error.40 : Focus servo does not operate.41 : With a DVD dual layer disc, focus jump failed.50 : CLV (spindle) servo does not operate.51 : Spindle does not stop.60 : Made a request to seek nonexistent address.61 : Seek error of retry more than regulated times.70 : Control data could not be read.80 : Disc reading failed.

5. MECHA ERROR HISTORYOn the Test Mode Menu screen, selecting [5] displays theinformation of mechanism deck error history.The history information from last 1 up to 8 can be scrolled withthe O key or o key.

### Mecha Error History ###

1. xx xx xx xx xx xx xx xx 2. xx xx xx xx xx xx xx xx 3. xx xx xx xx xx xx xx xx 4. xx xx xx xx xx xx xx xx 5. xx xx xx xx xx xx xx xx 6. xx xx xx xx xx xx xx xx 7. xx xx xx xx xx xx xx xx 8. xx xx xx xx xx xx xx xx

Scroll:UP/DOWN(1.Latest Err.) Exit: RETURN

25

HCD-NXM4D

aa: Initialization is completed or not.FF : Complete.

other number : Not complete.bb: Operating status of mechanism deck at an error occurred.

(lod sq jcp)00 : Initializing.10 to 15 : Open operating.16 to 19 : Kicking cause open failed.1A to 1F : Open operating.20 to 27 : Complete the open operation.28 : No disc and complete the open operation.29 to 2F : Complete the open operation.30 to 3F : Close requesting.40 to 4F : Open requesting.50 to 5F : Close operating.60 to 6F : Complete the chucking operation.80 to 8F : Complete the release operation.

(BU is home position)90 to 9F : BU down operating.A0 to AF : Opening/closing the shutter. Or stationary state

in open/close the shutter is enablement.B0 to BF : BU up requesting.C0 to CF : BU down requesting.D0 to DF : BU upping.E0 to EF : No disc checking in disc loading.

cc : Operating status of table at an error occurred. (tbl sq jcp) 13 : The rotation stop position determination error of a table 11 to 12 : The loading position determination error of a table

dd: Operating status of mechanism deck at an error occurred. (lod OP jcp)

00 : Complete the operation.10 to 1F : Open operating.20 to 2F : Close operating.30 to 3F : Release operating.60 to 6F : Chucking operating.70 to 7F : Kicking operating.80 to 8F : Returning the BU to home position. (after kicking)

ee : The status of table operation. (“n” is unfixed) (tbl op jcp) 1n : Rotating in the direction of a forward. 2n : Rotating in the direction of a reverse.

6. VERSION INFORMATIONOn the Test Mode Menu screen, selecting [6] displays the ROMversion and region code.The parenthesized hexadecimal number in version field is checksumvalue of ROM.

## Version Information ##

IF con. Ver.x. xx

SYScon. Ver.x. xx (xxxx)Model DHC-NXMXXRegion 0xConfig xxxxxxxx

xxxxxxxx Front End Ver.x.xx

Exit: RETURN

IF con. : The version of system controller (IC501).SYScon. : The version of DVD system processor (IC207).Front End : The version of mechanism controller (IC901).

7. VIDEO LEVEL ADJUSTMENT

On the Test Mode Menu screen, selecting [7] displays color bars forvideo level adjustment. During display of color bars, OSD disappearsbut the menu screen will be restored if pressing the [RETURN] key.

26

HCD-NXM4D

SECTION 5MECHANICAL ADJUSTMENTS

SECTION 6ELECTRICAL ADJUSTMENTS

Precaution1. Clean the following parts with a denatured alcohol-moistened

swab:record/playback heads pinch rollerserase head rubber beltscapstan idlers

2. Demagnetize the record/playback head with a headdemagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.4. After the adjustments, apply suitable locking compound to

the parts adjusted.5. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.

Torque Measurement

3.06 N • m to 6.96 N • m

FWD CQ-102C 31 to 71 g • cm

(0.43 – 0.98 oz • inch)

FWD0.19 N • m to 0.58 N • m

back tensionCQ-102C 2 to 6 g • cm

(0.02 – 0.08 oz • inch)

3.06 N • m to 6.96 N • m

REV CQ-102RC 31 to 71 g • cm

(0.43 – 0.98 oz • inch)

0.19 N • m to 0.58 N • mREVCQ-102RC 2 to 6 g • cmback tension

(0.02 – 0.08 oz • inch)

6.96 N • m to 14.02 N • m

FF/REW CQ-201B 71 to 143 g • cm

(0.98 – 1.99 oz • inch)

9.80 N • m

FWD tension CQ-403A 100 g or more

(3.53 oz or more)

9.80 N • m

REV tension CQ-403R 100 g or more

(3.53 oz or more)

Mode Torque meter Meter reading

0 dB=0.775 VDECK SECTION

1. Demagnetize the record/playback head with a headdemagnetizer.

2. Do not use a magnetized screwdriver for the adjustments.3. After the adjustments, apply suitable locking compound to the

parts adjust.4. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.5. The adjustments should be performed in the order given in

this service manual. (As a general rule, playback circuitadjustment should be completed before performing recordingcircuit adjustment.)

6. The adjustments should be performed for both L-CH and R-CH.

7. Switches and controls should be set as follows unless otherwisespecified.

• Test Tape

RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT

DECK A DECK B

Note: Perform this adjustments for both decksProcedure:

1. Mode: Playback

Tape Signal Used forP-4-A100 10 kHz, –10 dB Azimuth Adjustment

set

MAIN boardCN304Pin 1 (L-CH)Pin 3 (R-CH)

MAIN boardCN304Pin 2 (GND)

+–

level meter

test tapeP-4-A100(10 kHz, –10 dB)

27

HCD-NXM4D

2. Turn the adjustment screw and check output peaks. If the peaksdo not match for L-CH and R-CH, turn the adjustment screwso that outputs match within 1dB of peak.

3. Mode: Playback

4. After the adjustments, apply suitable locking compound tothe pats adjusted.

Adjustment Location: Playback Head (Deck A).Record/Playback/Erase Head (Deck B).

Screwposition

L-CHpeak

within1dB

Outputlevel

L-CHpeak

R-CHpeak

within1dB

Screwposition

R-CHpeak

MAINboardCN301set

test tapeP-4-A100(10 kHz, –10 dB)

pin 3

oscilloscope

L-CH

R-CH

V H

waveform of oscilloscope

in phase 45° 90° 135° 180°

good wrong

pin 2

pin 1

L

R

forwardreverse

VIDEO SECTION

Note :1. DBM07 board is basically designed to operate without adjust-

ment. Therefore, check each item in order given.2. Use DVD reference disc unless othermise indicated.

[DVD reference disc]• LUV-P01 (4-999-032-01) (CD)•TDV-540C (J-2501-235-A) (DVD-DL)• TDV-520CSO (J-2501-236-A) (DVD-SL)

3. Use an oscilloscope with more than 10MΩ impedance.4. Clean the object lens by an applicator with neutral detergent

when the signal level is low than specified value with thefollowing checks.

Video Level Check (DBM07 BOARD)PurposeThis adjustment is made to satisfy the NTSC standard, and if notadjusted correctly, the brightness will be too large or small.

Procedure:1. Connect oscilloscope to VIDEO output.2. Load a DVD reference disc playback.3. Check the video signal level is 1.00±0.05Vp-p.

J1102VIDEO OUTPUT

75 Ω

Oscilloscope

set

1.00 ± 0.05 Vp-p

(WHITE 100%)

RE-ADJUSTMENT OF THE SERVO CIRUITThe re-adjustment of the servo circuit is necessary whenthe part which relates to the servo circuit is replaced.Referring to “1. DRIVE AUTO ADJUSTMENT” (see page 20).Choose ALL and do the re-adjustment of each item ofDVD-SL, CD and DVD-DL.

THE PART THAT THE RE-ADJUSTMENT OF THE SERVO CIRCUIT IS NECESSARY.

1. Optical pick-up2. RF AMP (IC001)3. DSP IC (IC509)4. Motor driver IC (IC501)5. EEPROM (IC204)

28

HCD-NXM4D

RFMON Level CheckPerform a RFMON level check before exchanging optical pick-up.Connection:

RFMON signal waveform

• Standard value

Test DiscRFMON level

Standard Value

DVDTDV-520CSO

1.09±0.2Vp-p(J-2501-236-A)

CDLUV-P01

1.05±0.2Vp-p(4-999-032-01)

VOLT/DIV: 200 mVTIME/DIV: 500 ns

RFMON level

RR

C042R013

RC034

C036C035

C033C012

R031

C051

IC001

32

33 16

17

+–

JL005(RFMON)

oscilloscope

–RF board (side B) –

JL005(RFMON)

VC

29

HCD-NXM4D

SECTION 7DIAGRAMS

7-1. CIRCUIT BOARD LOCATION

FRONT AMP boardHP board

VOL board

DISC SW board

PANEL board

MAIN board

switching regulator

SUR AMP board

RF boardENCODER board

SENSOR board

MOTOR board

SW(1) board

SW(2) board

RELAY board

VIDEO board

DMB07 board

30

HCD-NXM4D

For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• f : internal component.• 2 : nonflammable resistor.• 5 : fusible resistor.

• C : panel designation.• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground

under no-signal conditions.RF, DMB07, VIDEO boards section

no mark: DVD PLAYOther board section

no mark: TUNER (FM/AM)( ) : DVD PLAY< >: TAPE REC[ ]: TAPE PLAY

* : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal produc-tion tolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.

• Circled numbers refer to waveforms.• Signal path.

F : TUNER (FM/AM)E : TAPE PLAY (DECK A)d : TAPE PLAY (DECK B)G : RECORDJ : DVD PLAYN : MIC INPUT

• AbbreviationE2 : 120V AC Area in E modelE3 : 240V AC Area in E modelEA : Saudi Arabia mdoelE15 : Iran modelSP : Shingapore modelMY : Malaysia modelAUS : Australian mdoelTH : Thai model

Note: The components identified by mark 0 or dotted linewith mark ! are critical for safety.Replace only with part number specified.

(The other layers' patterns are not indicated.)

• Indication of transistor.

• AbbreviationE2 : 120V AC Area in E modelE3 : 240V AC Area in E modelEA : Saudi Arabia mdoelE15 : Iran modelSP : Shingapore modelMY : Malaysia modelAUS : Australian mdoelTH : Thai model

Caution:Parts face side: Parts on the parts face side seen from(Side A) the parts face are indicated.Pattern face side: Parts on the pattern face side seen from(Side B) the pattern face are indicated.

C

B

These are omitted.

E

Q

B

These are omitted.

C E

Q

B

These are omitted.

C E

Q

Note on Printed Wiring Boards:• X : parts extracted from the component side.• : Pattern from the side which enables seeing.

HCD-NXM4D

3131HCD-NXM4D

7-2. BLOCK DIAGRAM – DVD DSP (1/2) SECTION –

• R-ch is omitted due to same as L-ch.• Signal path

J : DVDF : AUDIO

OPTICAL PICK-UPBLOCK(DBU-3)

A +5V

Q001

RF1

2

4

5

RF AC

TXD

RXD

CN901(RS232C)

IC001DVD/CD RF AMP

VC

CD A16CD B15CD C

SDEN

PI/CE

DATA RFCLK RF

MIRR

FFDR

AVC

FRDR

TFDRTRDR

SPIN

1413171820

1

21

CD D

A12B11C10

9 D

CD FCD E

DVD LD

A23B24C25

6 D2

DVDLD

PD

FCS+FCS-

TRK+TRK-

SW

DVDRFP

INLIM

IC501MOTOR/COIL DRIVE

36DO1-DO1+

DO2+

DO2-

DO3+DO3-DO4+DO4-

37

3435

32

19202122

30

DO5+27

IN6-46

IN6+47

29

DO5-28

31

481

40

34

10

7

13

3132

44

SLEDMOTOR

SPINDLEMOTOR

IN1+

IN1-

IN2+

IN2-

IN3-

IN4-

39POWERSAVE

IN5-

AVC AVC

45OUT6

SPO

SLED

_B

62

FG

7

FCS_

JMP_

1

8

FCS_

JMP_

2

61 8180

SLED RT

D

TXD

26

SCOR

CDSP

2

6

MNT

1

22

INIT

0_DV

D

23

INIT

1_DV

D

84XW

R85

XRD

12XC

S_DV

D25

XRST

_188

2

14-21D0-D7A8

89-96A0-A7

52

SQSO

54

SQCK

SLED

_A

TRDRTFDR

3334 FRDR

FFDR

IC901(1/2)MECHANISMCONTROLLER

57RFAC

321

4

MEVOIC003

OP AMP

31MIN

40FE

VC

VCC

BADCE

F

RF

DSP

GND

39TE

42

36

MNTR

VI25

39 FE

41 TE40 SE

434238

RFDCCEVC

RFIN

48SDEN47SDATA46SCLK

2

SDEN

40 XTALX901

20MHz 41 EXTAL

83

SDAT

A_RF

82

SDCL

K_RF

27MIRR

26LDON LDON

HDB-DATA

ANALDG-IN-L

INT/EXT

BCKLRCKXCK

XSRQ

XSAK#

SDEF#

XDCK#

I/O0-I/O15

768FS-2768FS-1

IC70616M DRAM

A0-A11

IC701DVD DECODER

IC509CD DECODERSERVO DSP

MDB0-MDB9,MDBA-MDZBF

MA0-MA9/MNT0

XMWR WEXRAS RASXMOE OEXCAS

MA11/MNT2

D0-D7 A0-A7

UCASLCAS

ANALDG-IN-R

SLEDA+SLEDA-SLEDB+SLEDB-

SPDL+

SPDL-

12

16

Q901

LDDRIVE

22 CD LD

23 DVDPD24 CDPD

CDLDLD GND

M

M

66

PI

50 RFAC

65LRCK66PCMD67BCK

71XTAI

69XTSL

76

SQSO

77

SQCK

79SBSO80EXCK

4

DATA

5

XLAT

6

CLOK

7

SENS

8

49 27 50 9 72

SCLK

DATA

_CD

LAT_

CDCL

OK_C

DSE

NS_C

DSC

LK_C

D

71

GFS_

CD

30

COUT

_CD

74

FOK_

CD

75

LOCK

_CD

31

INLI

M

10WFCK

13

GFS

14C2PO15SCOR17

45WDCK

21DFCT

19

COUT

22

FOK

24

LOCK

768F

S

25MDP

26

SSTP

MUT

E12

MUT

E34

MUT

E5TS

D-M

2957

6SFDR

30 SRDR

28

LDON

20 MIRR

76

LDSE

L

73

TSD-

M

63

SP_O

N

60

MUT

E_2D

43

135

164

MDIN2137

MDIN1138

MDSOUT142

117

LRCK163

65

TE

67

FE

29

MIR

R

Q002LD

DRIVE

IC503AMP

5 SDASCLWP

SDA_EEPSCL_EEPWP_EEP 7

65

99100

IC903EEPROM

IC703(1/2)AMP

IC703(2/2)AMP

MDAT160

APE0109 GFS 107

170

BCLK158SBIN148EXCK147

3

MUT

E

59

MUT

E_CD

2XR

ST

98

XDRS

T

WFCK151C2PO155SCOR150GSCORDFCT

146

46HDRQ

XSAK

HDB0

HDB7

HDB8

XDCK

XSAK#

SDEF#

XDCK#

AV7AV0AV1AV2AV6

XSAK#SDEF#XDCK#

INVERTER

48XHWR

XSAKXDCK

53XHACXSRQXSRQ

26HDB8 SDEF

XTL1

45

SCK_

DSD

58

GFS_

DVD

64

JIT

3

DOCT

RL/IS

BTES

T63

MD2

76

172-1761,2,4

5,7,9-14

17187833943435

95

XRD

17

XWR

18

XCS

19

XINT

0

20

XINT

1

21

HDB0-HDB7

MA10/MNT1 92

93

44,41,39,3532,30,27,24

66-69,71,73-75,

96,97,99,101,102,104-106

2-5,7-10,

41-44,46-49

79,80,82-87,89,91

21-24,27-32,20,19

8 8

XRST

XRST

B

A DVD DSP (2/2)SECTION(Page 32)

H MAINSECTION(Page 34)

DRV

DRV

DRV

DRV

42

43

DVD DSP (2/2)SECTION(Page 32)

10 97

-

-

2

9

-ID

8D

-1Q

8Q

-19

12

OE

IC256 DATA LATCH

IC258 DATA LATCH

IC259 DATA LATCH

Q201

R-CH

IC352 A/D CONVERTER

R-CH

L-CH

AVO-AV7

1

OE

OE

2 1D

3 2D

4 3D

191Q

182Q

173Q

1

191Q8 7D

7 6D9 8D

182Q171615141312

3Q4Q5Q6Q7Q8Q

151 VINL DOUT

2 VINR

ADC DATA

LRCKBCK

14 BCK13 LRCK

16 SYSCK

1

HCD-NXM4D

3232HCD-NXM4D

7-3. BLOCK DIAGRAM – DVD DSP (2/2) SECTION –

• Signal pathJ : DVDg : VIDEO

M-REQVMUTEVIDEO SWSYS RESET

I2C-CLK I/O

I2C-DATA

IC901 (2/2)MECHANISMCONTROLLER

131VDAC 0 VI/P SW

CY

CB/RCR/B

I2C-DA

D +3.3V

I2C-CL

125VDAC 2128VDAC 1

122VDAC 3

7-9

12-19

119

HA1-22

HA4-22

HA1-3

HA1-3

HAD0

-15

VDAC 4WIDE107VS

190ALE195HCS025WEH.UDS27HREAD

IC207DVD SYSTEM PROCESSOR

IC231,232,233ADDRESS LATCH

184

HIRQ

1DR

VIRQ

36

191

RST_

SPC

RST

38

DRVR

DY

37

161

I2C

DAI2

C_SI

O

78

160

I2C

CLI2

C_SC

L

79

202

RESE

T

185

DRVC

LKSC

K_ZI

VA

35

186

DRVT

XSO

_ZIV

A

34

187

DRVR

XSI

_ZIV

A

33

162

CS (Z

IVA_

E2P)

165

WRI

TE_C

TRL

(ZIV

A_E2

P)

116

HIRQ

2

188 DRVRDY

D+3.3VAUDIO+5V

CS_Z

IVA

32

3 MO1SO2SO3

27M768FS768FS768FS-2

768FS-1 1310

IC906CLOCK GENERATOR

IC111SWITCH

6CLR

CKQ3 1

21

4

IC904FF

IC902GATE

5DI4SK3CS1R/B

DOWC 8

6

IC204EEPROM

HDB-DATA

DCKLRCK

XCK

SDEN179X SAK#SDCLK183X DCK#

X SRQ SDREQ178

139XIN

IC203 SDRAM

DQ0-DQ31

A0-A9,A10/AP,NC

MD0-MD31

SDDATA0-SDDATA7,

MA0-MA11

HAD0-HAD15

MDQM0-MDQM3DQM0-DQM3MWEWEMCASCASMRASRASMCS0CS

12

32

8

4

5316,71,28,59

1718 5219 5120 49

BA0BS0 22 48BA1BS1 23

1 3

47MCLKCLK 68 56

CKE 67

57-6064-7175-7881-8488-95

99-102

2-9

2,4,5,7,8,10,11,13,

74,76,77,79,80,82,83,85,31,33,34,36,37,39,40,42,45,47,48,50,51,53,54,56

42-3345,46

22,19-14,11-3

HA1-HA3 2,207,206

177-174171-168

25-2760-6624,21

150DATA0(DM)151DATA1(FLR)154DATA2(SLR)155DATA3(CSW)

149BCK148LRCK147XCK

110MREQMREQ

BCK-1LRCK-1

XCK1

113MDI

108I/P SW

114MC115ML

MDIMCML

MDI

RSTAUDIOD +3.3V

MCML

Q202

1LE

IC302D/A CONVERTER

DATA3DATA2DATA1DATA4BCK

VOUT7

IC392

+3.3VREG.

A3V-2D +5V 1 3

IC907

+3.3VREG.

D +3.3V D +1.8V1 3

IC211

IC502

+1.8VREG.

D +5V A3V-11 3+3.3VREG.

VOUT8DM-LDM-R

SL-INSR-IN

LFE-IN

FL-INFR-IN

C-IN

VOUT1VOUT2

VOUT5

VOUT3VOUT4

VOUT6

LRCKSCKI

47464531404138

1620

1413

10

1211

9

363534

37

62,73,86,97

DATA1DATA0

DATA2DATA3

26

11

CE

DQ0-DQ15

A0-A21

HAD0-15

HAD0-15

11 WE28 OE

IC206RAM

29-36,38-45

25,24,23,22-18,8-1,48,17,16,9,10,13

7XTIX902

27MHz8XTO

D MAINSECTION(Page 34)

BDVD DSP(1/2)SECTION(Page 31)

CMAIN

SECTION(Page 34)

ADVD DSP (1/2)SECTION(Page 31)

23CVBS OUT4 CVBS INCVBS

6 Y-INY/G2 C-INC

12

14

CB-INCB/R

CR-IN

SI

13 MUTE2

3

9

MUTE1

I/P

10 CY-IN

CR/B

25WIDE

I/P SW

Y-OUTC-OUT

2126

IC1101VIDEO AMP/BUFFER

20CY-OUT

18CB-OUT

16CR-OUT

VIDEOOUTVIDEO

J1102

COMPONENTVIDEO OUT

J1103

S VIDEOOUT

J1101C Y

Y

PB/CB

PR/CR

SDERROR182SDEF#

4 3

61

2S-CD

1S-1D

2,5

I/PSWITCHQ1101

HCD-NXM4D

3333HCD-NXM4D

7-4. BLOCK DIAGRAM – TUNER/TAPE DECK SECTION –

TUNER

Q25,26Q270

R-CHL OUTR OUT

ST-MUTETUNERST-CE

ST D OUTST D INST CLK

STEREO

DECK-A

DECK-B

L

R

HP901

HP901

L

R

HE901

HRP901

HRP901

TAPE

F REC

B SHUTA HALFA PLAYB PLAY

A HALFA PLAYB PLAY

R-RECB HALF

A SHUT

CAPM+

A TRIG+

B TRIG+

R-CH

R-CH

Q303Q314,315

Q301,302Q311-313

Q104Q31,22R-CH

L

R

R-CH

L

R

VIDEO/SAT

MIC1J1060

J1061MIC2

MECHANISM DECK

64

61

66

27

18

505152535455

63

5

10

3

11

REC/PBSWITCH

MUTESWITCH

REC/PBSWITCH

BIASOSC

Q318T301

Q316,317BIAS

REC/PB

BIASSWITCH

TC RECMUTE

12

CAP MDRIVE

Q326,327

Q323,324

Q321,322

IC1060(1/2)

IC1061MIC ECHO

RV1060

A TRIGDRIVE

9091

86

89

87

88

3

29

4

67 468 2669 25

65

58

97100

92

LINE MUTE

A MUTE

ST-MUTETUNEDST-CE

ST-DINST-CLK

B HALF

FDRONT RELAY

57STK-MUTE

56TA MUTE

STBY RELAY

I/O EXP CLK

M16537 CLK

M16537 DATA

SPEC-INVACS INAMS IN

I/O EXP LAT

I/O EXP DATYA INI/O EXP DATA OUT

CLK

DATA

D182

A SHUT

A TRIG

B TRIG

MIC SW

LPF1 INLPF1 OUT

LPF2 OUT

CAPM-CNT1

TC REC MUTE

60 TC REC/PB

59 BIAS

B SHUT

ON/OFF(SWITCHING REGULATOR)

ST-DOUT

8081

19

8

20212223

18

17

9

R-CH

CN102

SURR-L

FL-OUT

AMPSECTION(Page 35)

MAINSECTION(Page 34)


AMPSECTION(Page 35)

CN103

Q21,22Q1Q101

FL

SW

FR

SW

DBFB FEED BACKPROTECT

STK MUTEFRONT RELAY

HP SWFAN CTL

SW RELAY

MIC SIG

63

62

71

70

68 67 66 65

7 8 11 53 51

56

50 5948 34 35

R-CH

Q341-343Q103Q29,30

Q140Q33,34

SELECTOR

R-CH

AMSDPL-2

DPL-2

42 41 37

29

R-CH

S2

FL

CLK DATA

CLK DATAEQ

AGC

MD BUSTONE

TRE

AMSMUTE

AMSBUFFER

PB MUTE

LEDSWITCH

LEDSWITCH

AMS-MUTESTEREO

Q1026

D1021

D1001-1005

Q1001-1005

B PLAYA PLAYA HALF

CLK

LED 9V

VCC

LATCHDI 1DO 2

IC951I/O EXPANDER

IC401 (1/2)SYSTEM CONTROL

IC101INPUT SELECT SWITCHELECTRICAL VOLUMEI

HP IN

HALF PLAY

AMS MUTEDISC1

DISC2DISC3DISC4DISC5

PROTECT

24

7SW RELAY

FAN

MUTESWITCH

B TRIGDRIVE

Q401MIC

SWITCH

SURR

UNREG+5V

SWITCHINGREGULATOR

UNREG+12V

AC-IN

MCUI/F

I

E

L

K

SW-OUTM

F

52

IN

OUT

ANALOG-IN-L J

3031

BUFFER

TA MUTE N

RV1061

IC1060(2/2)

Q903.904

REG SW

3

IC901

REG 1

3

IC903

REG 1

AUDIO+9V

Q901

REG

2

5

IC906

REG 1D+3.3V

2

5

IC905

REG 1D+5.5V

M+9V,LED+9V 3

IC902

REG 1

D+3.3V

Q906

REG

DVD+5V

2

4

IC904

REG 1M+12V

Q902

REG SW

G DVD POWER

3 1

MIC LEVEL

ECHO LEVEL

6 7

MAINSCTION

(Page 34)

R-CH

L-OUTR-OUT





HH

H


F : TUNERE : PLAY BACK (DECK A)d : PLAY BACK (DECK B)G : RECORDJ : DVDN : MIC

HCD-NXM4D

3434HCD-NXM4D

7-5. BLOCK DIAGRAM – MAIN SECTION –

IC401 (2/2)SYSTEM CONTROL

FL-DATAFL-CLKFL-CS

FL-RESET

M61530CLK

DVD POWER

DVD A MUTE

M61530DATA

SIRCD

AD-KEY2

AD-KEY1

JOG2-A

JOG1-A

VOL-A

POWER KEY

DISPLAY KEY

XC-IN

X-OUT

XC-OUT

X-IN

858483

33 LD MTR POSU/D MTR NEGU/D MTR POS

SUB TRAY OUTSUB TRAY INTRAY CLOSE SWTRAY OPEN SW

ST-E1ST-E2ST-E3ST-E4MD-E1MD-E2MD-E3MD-E4D,SENSER

EVER+4V

EVER+4V

4734463545

CDN-MOT-NEG-1(LD)CDN-MOT-POS-1(LD)

CDN-MOT-NEG-2(U/D)CDN-MOT-POS-2(U/D)

CDM-MAIN-SW-OPEN(SW2)CDM-MAIN-SW-CLOSE(SW4)

CDM-SUB-SW-OPEN(SW2)CDM-SUB-SW-CLOSE(SW3)

CDM-ENC-B-3(MDM4)CDM-ENC-B-2(MDM3)

CDM-ENC-B-1(MDM2)CDM-ENC-B-0(MDM1)

CDM-ENC-A-3(STE4)CDM-ENC-A-2(STE3)

CDM-ENC-A-1(STE2)CDM-ENC-A-0(STE1)

DISC SENS

LED-STANDBY

RESET

AC-CUT

48 LD MTR NEG

CLCK

DATADVD POWER

1

2

28

27

3644

43384239

37

414075

REAR RELAY 6

72

12

20

SW MUTE 19 LD/ST MTR POSBU U/D MTR NEGBU U/D MTR POS

SW3 SUB TRAY OUTSW2 SUB TRAY OUT

SW4 SUB TRAY CLOSE OUTSW1 SUB TRAY OPEN OUT

ST-E1ST-E2ST-E3ST-E4

MD-E1MD-E2MD-E3MD-E4

D,SENSER

LD/ST MTR NEG

CN201

ANALOG-IN-R R-CH

R-CH

CN104

RELAYC-INSR-INSL-IN

SURR-R

SURR-L

R-CH

FL-OUT FL-OUT

R-CH

L-OUTR-OUT

ANALOG-IN-L

L-OUT

R-CH

ANALOG-IN-LQ102

DM-L L OUT

DM-R

DM-LDM-R

SL-INC-IN

FR-INFL-IN

SR-INLFE-IN

ANALOG-IN-L

OUTSIRCS

IC1050

41

KEY2-1KEY2-2

S1043S1001-1005

S1051

KEYNETWORK

94

ROTARYENCODER

ROTARYENCODER

ROTARYENCODER

TREBLE 78JOG2-B79

S1050

76JOG1-B77

S1052

S1042

70VOL-B71

74

95

BASS

BASS

X40136.768kHz

X40216MHz

VOLUME

S1021-1027,1029-1031S1032-1036

REMOTECONTROLRECEIVER

KEYNETWORK

S102873DISPLAY

10

11

13

15

82

LEDSWITCH

MUTESW

Q270

MUTESW

Q271

MUTESW

Q272

MUTESW

Q273

MUTESW

Q274

MUTESW

Q275

MUTESW

Q276

MUTESW

Q277

MUTESW

Q25,26

S,WSURR-L

DVDA MUTE

Q1041

D1050

IC391RESET

Q391

3 1LEVEL

DETECT

IC701LD/ST MOTOR DRIVER

9 RINFIN

OUT1M761

(LD/ST)ROTARY

ENCODER(ST U/D)

S781

OUT2742

IC711U/DOTOR DRIVER

9 RINFIN

OUT1OUT27

42

25 SYS RESETVIDEO SWVMUTE

I2C DATAI2C CLK I/O

24232930

DVD MUTE REQDVD SYS RESTDVD VIDEO SW

DVD VIDEO MUTEIIC-CLK

IIC-DATA

26 M-REG

IC1020DISPLAY CONTROL/KEY CONTROL

IC201INPUT ATTENUATOR

LPF, AGC, BASS BOOST

8765

51I

15

3•2•1•

64I

57

56•

55

4

54

GREIDDRIVE

Q1021

GRIDDRIVE

Q1022

55 GRIDDRIVE

Q1023

SDATASCKCSRESET

SEG00I

SEG35

DEG01

FL1020FLUORESCENT

INDICATORTUBE

F1

F2

DEG11

DEG12/SEG36

DEG13/SEG37

DG00

DIG14SEG38

VF1

VP D/D CON+9V

Q1024T801D1023-1026

VF2

VPRECT

BIASOSC

DVD DSP(2/2)SECTION(Page 32)

D

G

L

Q23,24,40

ANALOG INMUTE

37 38

R OUT39

EL OUT34

12

5

FL IN

40

FR IN

41

CIN

2

SL-IN

13

SR-IN

6

SWSW

10

LFE-IN14

15

9

24

11

3

4

25

8

9

23

32

33

22

29

26

SW-LPF

Q3

MUTESW

R-ch

Q21,22

TAMUTE

DATACLOCK

Q19,20

SWMUTE

Q6

SWMUTE

Q4

SW

MUTESW

M

O

TA MUTE

DATA

CLOC

K N 17 18

M

M762(U/D)

MAIN TRAYOPEN/IN

S721

S731

OPEN

CROSE

M

(SUB TRAY OUT)

(SUB TRAY OUT)S761

ROTARYENCODER

(MD)

S771

SENSESWITCH

Q751

D+3.3V

IC751(DISC SENSOR)


H


TUNER/TAPEDECK

SECTION(Page 33)

TUNER/TAPEDECK

SECTION(Page 33)

C

J

I

K

TUNER/TAPE DECKSECTION(Page 33)



AMPSECTION(Page 35)




F : AUDIOJ : DVD

HCD-NXM4D

3535HCD-NXM4D

7-6. BLOCK DIAGRAM – AMP SECTION –


F : AUDIO

18

19

STKMUTE

SWITCH

8 9

FL

FR

SW

DBFB FEED BACK

CN501

R-CH

STK MUTE

FRONT RELAY

HP SW

FAN CTL

PROTECT

SW RELAY

CN508

FAN

3

2

1

4

10

11

22

21

-VHSUPP

TEMPDETECT

MUTESWITCH

-VH

D501Q507,508

D507

Q854

RELAYDRIVE

Q509

R-CH

R-CH

SL IN

SR IN

C IN

RELAY

R-CH

R-CH

L

Q854

IC850OVER CURRENT PROTECTER

IC601SURROUND AMP

IC501POWER AMP

Q850-852

Q501,502Q503

Q858-861

MUTECONTROL

OCP

OUTVP

CT

Q868,869,890

Q505

-PRE +PRE

TM502

+VH

OVERLOAD

DETECT

SPEAKERPROTECT

RELAYDRIVE

RELAYDRIVE

Q510

R

L

R

PHONES

SUB WOOFER

FRONT

SURROUND

CENTER

J1063

Q506OVERLOAD

DETECT

FANMOTORDRIVE

FAN

E

F

TUNER/TAPEDECK

SECTION(Page 33)

TUNER/TAPEDECK

SECTION(Page 33)

OMAINSECTION(Page 34)

3

15

8

13

Q603 Q601

Q610

SL SP

C SP

PROTECT

OVER DCDETECT

OVER DC CURRENT DETECT

PROTECTSWITCH RELAY

DRIVE

SPEAKEROUT

CN601

PROTECTSWITCH

HCD-NXM4D

3636HCD-NXM4D

7-7. PRINTED WIRING BOARD – RF SECTION – • See page 29 for Circuit Boards Location.

Ref. No. Location

IC101 D-8IC251 C-6IC301 C-8IC303 B-8

Q10 E-4

• SemiconductorLocation

C023

C028

C040

C037

R004

R005

C038

C022C020

R016

R003

R018

R014R012

C027C0

41

C010

Q002

Q001

R007

C039

R001

C021C013

R009

R008

C008

EE

C017C015

C011

C009

R021CN00

3

CN001124

CN00

2

C049

IC003R033

13

54

R034R047R046

C050

C052

R091

R024

R025

R023C029 C026R026

C024

R027

R017R015

C042R013

R019

L002

L001

C003

D002

D001

R022

R020

C031

R011

C006

C005

C034

R006

R028R029

C036

C032

C035JL005

RFMONC033

C004

C012

C025R0

10

C002

C030

C018C016

C014

C019

R035

C001

R041

R031

C051VC

IC001

32

33

4849 64

1

16

17

12(12)

1-684-822-12(12)

1-684-822-

ADMB07BOARD

(Page40)



(SIDE A)RF BOARD (SIDE B)RF BOARD

2 3 4 5 6 7 8 9

A

1

B

C

D

HCD-NXM4D

3737HCD-NXM4D

7-8. SCHEMATIC DIAGRAM – RF BOARD – • See page 63 for IC Block Diagram. • See page 62 for Waveforms.

JL001

JL003

JL006C014

C015

C016

C017

C018

C019

JL002

JL004

C020

C021

C022

C023

C042

CN001

CN002

L00147uH

L00247uH

R006 R010

R011

R012

R013

R014

R015

R016

R017

R018

R021

R025

R027

R028

R029

IOP1IOP2

JL005

JL007

CN003

D001 D002

R031

R047

IC001

Q002Q001C002C010

IC003

R004R003

R005

R007 R008

C0340.1u

R091

C036

C040

C051

C039

C038

C037

C041

C050 R046

C011

C004

C001 C003R009

C012 C005C033C032

C006

C013

C031C029

C030

C028C027

C025

C026

C024

R026

R023R024

C008

C009

R001

C049

C035

R020R019

C052

R033

R034

R022

2200p B

2200p B

2200p B

2200p B

5600p B

5600p B

22p

CH22

pCH

22p

CH22

pCH

180p CH

24PTO DBU-1

29PTO MAIN

470 470

0

0

0

0

0

0

0

0

0

100

0

0

0

9PTO DBU-1/KHM240A

/KHM270A

1SS355TE-17 1SS355TE-17

100

33k

SP3723CAF0PM

2SB1132-T100-QR2SB1132-T100-QR1016V

1000p

TL343IDBVR

3333

47k

33 33

B

560k

0.47

0.1

0.47

0.03

3

0.03

3

680p

0.1

0.0033 10k

1000p

1016V

1006.3V

1006.3V

47k

0.1 2210V

0.10.047

2210V

0.1

1000p0.01

0.01

0.10.1

0.1

0.1

0.01

12k

8200

0.1

0.1

100

0.1

0.1

00

0.1

100k

470

220

MIRR

CD_LD

DVD_LD

LDON

SDEN

DATA_RF

CLK_RF

LDONA

B

C

D

F

TE

FE

MIRR

PD

RFMON

B

A

F

D

C

CD_LD

DVD_LD

PDFD-

FD+

TD-

TD+

FD+

FD-

TD+

TD-

SLB-

SLB+

SLA-

SLA+

PI/CE

SLA+

SLB+

SLB-

SLA-

FE

TE

PI/CE

SDENDATA_RF

CLK_RF

RFMON

DVD/CD RF AMP

OP AMP

BOARDDMB07

(1/6)(Page42)

HCD-NXM4D

3838HCD-NXM4D

7-9. PRINTED WIRING BOARD – DVD MECHANISM BOARD – • See page 29 for Circuit Boards Location.

JW701

S761(SUB TRAY OUT)

R753R754R751

C702

JW71

3

Q751

R752

R755

JW71

2

JW709

JW710JW711

JW714

IC71

1R7

12

R711

C701

JW702R701

R702

CN761

CN751

JW705

JW707JW708

JW706

IC701

CN70

5

CN731

CN771CN701

C703

IC751

JW703

JW704

S721(MAIN TRAY IN/OUT)

S731(SUB TRAY N)

S771ROTARY ENCODER

(MD)

S781ROTARY ENCODER

(ST U/D)

CN721

JW715

JW716JW718

JW71

9

JW720 JW71

7

CN70

6

CN70

2

CN707

CN703

C762

C761

D701D7

11

MOTOR BOARD

SENSOR BOARD

SW(2) BOARD

SW(1) BOARD

ENCODER BOARD

RELAY BOARD

12(12)1-861-241-

12(12)

1-861-242-

12(12)1-861-243-

11(12)1-861-245-

12(12)

1-861-244-

12(12)1-861-240-

MAIN BOARD

(Page 50)B

M761(LD/ST MOTOR)

M762(BU U/D MOTOR)

43

21

G

1

1

1

1

11

1

1

6

2

3

3

3

3

1

1

2

2

3412

34

G

G

9

9

20

21

16

2 3 4 5 6 7

A

1

B

C

D

E

F

Ref. No. Location

D701 D-4D711 D-4

IC701 D-4IC711 E-3IC751 B-6

Q751 D-2


HCD-NXM4D

3939HCD-NXM4D

7-10. SCHEMATIC DIAGRAM – DVD MECHANISM BOARD –

M761

M762

S761

S731 CN731 CN703

IC751

CN751 CN705

R711R712

D711

IC711

D701

C762

C761 R702

R701

C701

IC701

CN702 CN721S721

CN701

C702

R751

R754 Q751

R753

R752R755

CN707 CN771

S771

S781

CN706CN761

RF500TB

RF500TB

(SUB TRAY OUT)

(SUB TRAY IN) 2P 2P

RPR-359F

3P 3P

680100

MTZJ-T-77-4.3A

BA6956AN

MTZJ-T-77-4.7B

0.01

0.01 100

680

4716V

BA6956AN

3P 3P(MAIN TRAY

IN/OUT)

21PIN

1016V

91

12k 2SC2785-HFEDISC SENSOR

10k

10k10k

5P 5P

ROTARY ENCODER(MD)

ROTARYENCODER

6P6P

ST-E2ST-E3ST-E4

ST-E1

ST-E4ST-E3ST-E2ST-E1

(1/3)(Page 51)

• See page 66 for IC Block Diagram.

HCD-NXM4D

4040HCD-NXM4D

7-11. PRINTED WIRING BOARD – DMB07 BOARD (Side A) – • See page 29 for Circuit Boards Location.

OMAIN

BOARD(Page50)

KMAIN

BOARD(Page50)

ARF

BOARD(Page36)

NMAIN

BOARD(Page50)

PVIDEOBOARD

(Page48)

C576

R964

C539

JW501

R805

JW801

JW806JW805

JW802JW804

JW803

A5

A6

A9

A10

A13

A14

A17

A18

A15

A16

A19

FL703

CN101

R718

R769

C717

R767

C777

C778

C779

C780

R975

CN901

FL702

R908

R765R764

R763

R762

C702

R250R2

15

C705

IC90

6

IC9041 4

18

169 8

13

4 55 IC902

C706

C708

C530

C711

FL20

4

C712

R927 R9

31

C130

2

C917

C916

C915C914

C907

C715

C716

C533

C556

C561

R751

C588

X902

C771

C773

C774

C701

FL70

1

IC701

C259

C258

R601

R788

R707

R708

R226

R225

R327

R296

R217

R916

R219

R709

R629

R984

R284

R283

R277

R276

R275

R274

R273R2

69

R917

R15

R268

R505

R267

R266

R265

R264

R263

R14

R988

R254

R13

R994R995

R997

R998

C364

C357

C356

C355

R571

C352

R711

R234

R712

R231R230

153

104

208

157

52

156 105

C781

R552

R5481

1

3

2021

1

4

8

5

40 41 6061

80

C213

C215

R202

C325

1

12

36

25

13 24

48 37

C321

R714

C305

X901

C304

C303

121

2D1

303

D130

4R1

302

R978

IC259

IC25

8IC

256 1

10

20

12

34

11

110

21

1617

2011

110

2011

R716

IC207

FL20

5

D202

CN202CN105

R717

R719

FL20

6

C502

R907

R906

R905

C552

C201

C517

C518

R921

R922

R923

C522

R928 R929

C526

11 7

1 44

132 89

4588

176

133

229

28

C528

C101

C151

JW39

2

C531

C534

C535

C543

C544C5

45

C548 C5

51C553

IC211

C558

C560

C563

C565

C567

C568

C569

C573

C590

C366

FL101

C901

C902

C924

12 12

13

C903

C905

C926

C927

R962

R958

C592

R747

FB10

5

C202

R748

CN501

D901

FL50

1

FL50

2

FL90

1

IC503

IC509

IC901

C532

R758

C286

C284

L103

R760

R504

C266

C265

C263

R506

Q201

E

R510

R511

R523

C261

R599

R593

C253

C252

R588

R586

R584

R9985R3

14

C925

C3941 13

C393

C392

C248

R940

R942

R572

R943

R568

R567

C246

R566

R565

R564R563

R562

IC302

CN102

R561

R560

FL352

R559

FL30

3

FL302

R9984 R9983

R9982

C245

C242

C241

C239

CN10

7

R970

C227

R551R550

C214

R545

R536

R938

R936

R213

C283

C278

C277

C904

125

265051

75

76 100

C306

R197

R198

C287

C279

IC231110

2011

110

2011

IC232

C733

C291

L501

C547

(SIDE A)DMB07 BOARD

12(12)

1-861-848-

R299

2 3 4 5 6 7 8 9 10

A

1

B

C

D

E

F

G

Ref. No. Location

D1303 C-1D1304 C-1D202 D-6D901 E-3

IC207 C-8IC211 D-6IC231 E-9IC232 E-9IC256 C-7IC258 C-7IC259 B-7IC302 C-2IC503 D-5IC509 E-6IC701 E-8IC901 D-4IC902 D-7IC904 D-7IC906 D-7

Q201 B-7


HCD-NXM4D

4141HCD-NXM4D

7-12. PRINTED WIRING BOARD – DMB07 BOARD (Side B) – • See page 29 for Circuit Boards Location.

R549

R270

JW393

IC392

IC90

7

IC50

2

JW35

2

B5

B6

B8

C542

B7

B11

R369

R368

C727

C767

C769

R789

C729

FL70

6

R799

R777

R776

R778

C703

R335

FL90

3

C709

FB903

FB90

2

R932

R933

C713

C714

C516

C524

C718

C720

C721

C722C723

C724

C725

C726

C728

C730

1

110

2011

25

5026

C740

C741

C742

C743

C744

C745

C752

C760

C761

C762

C763

C765

C766

C768

C772

C775

C782

C783

FL70

5

C367C368

R785

R786

IC706

R700

C275

C264

C205

R787

R294 R293

R222R221

R228

R100

0

R329R328

IC206

R220

C540

R282

R281

R280

R279

R278

R261

R260

R514R515

R259

R257

R255

R522

R253

R251

R527

R248

R247

R246

R245

R244

R990

R241

R240

R239

R996

C363

R12

R11R10

R232

R227

C326R7

13

Q202

E

C324

C323

C322

R534

R915

C309C308

C307

R918

R715

IC204

FL203

R720

R721

R724R725

C501

R726

R727

R974

R728

C928R730

R731

R732R733R734R735R736R737R738

R913

R912

R911

C508

R904

R902

R901

14

85

C365

C509

C510

C511 C5

07

C512C5

14

C515

R741

R920C5

19R925

R926R930

C506

C504

C503

C525

C527

C529

D392D500R7

42

C570

R743

C589

C513

R744

R745

C906

C908

C909

C910

C913

C918

R746 C5

21C5

23

FL90

8

IC501

IC903

R750

Q901

E

D393

D394

R699

R698

R694

R503

R392

C272C271

C270

143

8644

C269

C268

C267

R935

C262

R512

R513

112

14

85

13

2425 36

37

48

R516

R517

R519R5

20

R521

R524

R525

C260

C257

C256

C255C254

R591

R589

R581

R580

R362

R353

R352

R313R312

R311

R310

R579

R309

R308

R307R306

R573

C251

C250C249

C247

R305R304

R303

R302

IC352

112

2413

R9980

C244

C243

R9981C240

C238 C237C236

C235

C234

C233

R9998

R9999

C232

C231

C230

C229

R555

C226

C220C218 C2

16

C204

14

85

R537

R533

R530

R529

C290

C280

C281

L901

R291

C276

C274

R292

C282

R301

IC203

R272R271R290

IC233

1 24

48 25

C203 C734

IC703

C764

L704

C776

R576

R583

C102

IC111

R367

(SIDE B)DMB07 BOARD

12(12)

1-861-848-

2 3 4 5 6 7 8 9

A

1

B

C

D

E

F

Ref. No. Location

D392 F-8D393 F-9D394 F-9D500 F-6

IC111 B-7IC203 C-1IC204 C-3IC206 D-1IC233 E-1IC352 B-9IC392 F-9IC501 E-5IC502 F-7IC703 E-4IC706 E-2IC903 D-6IC907 E-8

Q202 B-3Q901 E-7


HCD-NXM4D

4242HCD-NXM4D

7-13. SCHEMATIC DIAGRAM – DMB07 (1/6) BOARD – • See page 64 for IC Block Diagram. • See page 62 for Waveforms.

D901

R503

R510

R529

R530

R534

R536 R537

R545

R548

R550

R551

R552

R559

R563

R564

R599

R555

R562R561

R558

R560

R533

R520

R524

R512

C592

R515

R591

R527

R523

R525

L103

R587

R581

R580

R579

R572

FL501

D500

R583

CN501

IC907

R694

R698

R699C590

C589

C588

C532 C523 C521 C530

C503

C512

C514

C519

C515

C540

C511

C513

C516C570

C569

C522

C531

C533

C534

C535

R593

R588

C551

C573

C548

C547

C552

C565

C563IC502

R506

R505R504C502

C501

R571

R568

R601

C560

C559

R566

R565

R567

R584

C553

C556

C561C558

R576

C567 C568

C927C926

C928C925

C101

FL101

R573

C545C543

R589

C528C529

R514 C524

C525C504

R513

R516C506

R586

R517

C508

R521

R519

C510

R522C509

IC501

C544

C526C527

IC503

L501 C507

CN102

FL502

R511

C518

C517

C151 FB105

IC509

1SS355TE-17

47k1/10W

150k1/10W

33k1/10W

56k1/10W

56k1/10W

10k1/10W

68k1/10W

10k 1/10W

10k 1/10W

1k 1/10W

1k 1/10W

1k 1/10W

1k 1/10W

1k 1/10W

1k 1/10W

1k1/10W

0

1k 1/10W1k 1/10W

47k1/10W

1k 1/10W

33k 1/10W

10k 1/10W

10k 1/10W

56k 1/10W

1016V

10k1/10W

0

2.2k1/10W

10k 1/10W

10k 1/10W

0

0

12k1/10W

33k1/10W

8.2k1/10W

470k1/10W

0UH

1SS355TE-17

0

29P

2

10k1/10W

0

00.0022

0.0022

0.0022

10 0.1 0.1 10

33000p

0.01

0.01

0.01

220p

10

220p

10

0.002210

0.1

0.1

0.04

7

0.00

220.022

0.0022

100k1/10W

10k1/10W

0.47

100p

0.01

0.1

0

0.1

100p E2

47k1/10W

47k1/10W

47k1/10W

0.01

0.01

1M1/10W

1M

0

0.0015

0.1

10k

1/10

W

1k1/

10W

3.3k

1/10

W

33k1/10W

0.0033

10

0.11004V

0

0.01 10

0.012204V 10

2216V

2204V

0UH

10k1/10W

100.01

10k1/10W

2216V0.01

10k1/10W

0.01

0.01

33000p

56k1/10W

4.7k1/10W 330p

200k1/10W

2.2k1/10W

0.001

100k1/10W

100k1/10W

0.001

4.7k1/10W

330p

FAN8035L

0.1

2216V 0.01

NJM3404AV(TE2)

0 10

13P

0UH

150k1/10W

0.01

10

1006.3V

0UH

CXD3068Q

VGND

D3V

D5V

AUDIO_AGND

AUDIO_5V

V5V

A3V-2

DSP BUS

ANALOG BUS

SPC970_BUS

A3V-1

DGND

A5V

1.65V

PI

TE

FE

FE

TE

RFAC

RFAC

MIRR

DATA_RF

EXCK

SBSO

BCLK

MDAT

LRCK

WFC

K

GSCO

R

SQCK

SQSO

DFCTFO

K

LOCK

XRST

_CD

DATA

XLAT

CLOK

SENS

SCLK

COUT

MIR

R

MD2

SCOR

RF_A

C

MDP

MUT

E_CD

C2PO

LDON

768FS

FETE

SDEN

CLK_RF

SLEDA-

SLEDA+

SPDL+

SPDL-

MUT

E_2D

PI

SLEDB+

SLEDB-

TFDR

TRDR

FFDR

FRDR

TFDR

TRDR

SLED

B

SLED

A

FFDR

FRDR

SPFG

TSD-

M

PI

INLIM

RFM

ON

SLED

SLEDCTRL

SLEDCTRL

GFS_

CD

LDSE

L

SP_O

N

SPIN

FJM

P2

FJM

P1

FCS+

FCS-

TRK+

TRK-

SLEDA+

SLEDA-

SLEDB+

SLEDB-

SPDL+

SPDL-

TRK+

TRK-

FCS+

FCS-

DSAV

E

CDSP2

SPINDLE/SLED MOTOR DRIVE,FOCUS/TRACKING COIL DRIVE

DC DECODER

DIGITAL SERVO PROCESSOR

AMP

+3.3V REGULATOR

+3.3V REGULATOR

BOARDRF

BOARD

(Page4/6)

BOARD(5/6)

BOARD

(6/6)

BOARD BOARD(2/6) (3/6)

BOARD BOARD

BOARD BOARD

(2/6) (3/6)

(5/6) (6/6)

BOARD BOARD

BOARD BOARD

(2/6) (3/6)

(5/6)(4/6)

BOARD(2/6)

DMB07 DMB07

DMB07 DMB07

DMB07 DMB07

DMB07

DMB07

DMB07DMB07

DMB07DMB07

DMB07

DMB07

BOARDMAIN

(1/3)

(Page43)

(Page43)

(Page43)

(Page43) (Page44)

(Page44)

(Page44)

(Page45) (Page46)

(Page46)

(Page46)

(Page47)

(Page47)

(Page51)

(Page37)

HCD-NXM4D

4343HCD-NXM4D

7-14. SCHEMATIC DIAGRAM – DMB07 (2/6) BOARD – • See page 64 for IC Block Diagram. • See page 71 for IC Pin Function Description. • See page 62 for Waveforms.

R726

R720

R767

R737

R735

R727

R738

R736

R734

L704

R718

R715R7

13

R712R709

FL701

FL702

R741

R742

R743

R747

R700

IC701

C721

C703

C715

C708

C772

C765

C761 C760

C742

C723

C782

C712

R745

R746

R744

R733

R787

R788R785C783

C705C733

R786R789

C718

C722

R728C728

R725

R721 C720

R708

R710C711

R711

R748 R714C716 C717

R717R716

R719

C775R765

R763

R751

C776

C734

C774

C773

C771

R762

R769

R760R758

FL703

C780 C777

R777

R776

R750

C764 C763 C762

C744

C726

R732

C740

R731

R730

C725

C724

C727

FL705

C702

C730

C767

C770

C779 C778

C769

C768

R799

C766

R778

IC703(1/2)

IC703(2/2)

C781

C701

R764

C743

C745

C741

C706C752C709C713C714

FL706 C729

R724

IC706

100k1/10W

1k1/10W

47k1/10W

10k 1/10W

10k 1/10W

3.3k1/10W

10k 1/10W

10k 1/10W

10k 1/10W

10k1/10W

10k

1/10

W

10k

1/10

W

10k1/10W150k

1/10W

0UH

0UH

22 1/10W

22 1/10W

221/10W

33k

1/10

W

8.2k1/10W

TMC57929PGF-RDP

0.1

0.1

0.0015

0.01

0.01

0.01

0.01 0.01

0.01

0.01

0.0015

100p

47k1/10W

47k1/10W 22

1/10

W

10k1/10W

100k1/10W

100k1/10W

10k1/10W 0.0015

0.0110

100k1/10W100k

1/10W

0.01

0.01

10k1/10W 0.1

1.8k1/10W

33k1/10W 0.1

470k1/10W

10k1/10W 0.047

2.2k

1/10

W

33k1/10W

10k1/10W 0.47 0.01

100k1/10W

1001/10W

1k1/

10W

0.0122k1/10W

8.2k 1/10W

0

0.01

10

0.0047

0.47

0.047

22k1/10W

2.2k1/10W

0 0

0UH

10 0.01

0

0

10k 1/10W

0.01 0.01 0.01

0.01

0.01

10k1/10W

0.01

22 1/10W

22 1/10W

0.01

0.01

10

0UH

10

0.01

0.01

0.01

10 0.01

0.01

0.01

0

100p

100k1/10W

NJM3404AV(TE2)

NJM3404AV(TE2)

1504V

1504V

1M1/10W

0.01

0.01

0.01

0.010.10.10.10.1

0UH 10

1k 1/10W

MSM51V18165B-60TSKR1

DSP BUS

BUS 5

ANALOG BUS

SPC970_BUS

SIGNAL_BUS

D3V

A5V

A3V-1

1.65V

DGND

768FS

SD7

SDEF

SD6

SD5

SD4

SD3

SD2

SD1

SD0

BD0

BD1

BD2

BD3

BD4

BD5

BD6

BD7

WE

RAS

MA0

MA1

MA2

MA3

MA8

XMOE

XCASBD

8

BD9

BDA

BDB

BDC

BDD

BDE

BDF

BD0

BD1

BD2

BD3

BD4

BD5

BD6

BD7 BD8

BD9

BDA

BDB

BDC

BDD

BDE

BDF

MA0

MA1

MA2

MA3 MA4

MA5

MA6

MA7

MA8

XCASWE

XMOERAS

MA4

MA5

MA6

MA7

XSAK

XDCK

XSHD

D4

D3

D2

D1

D0

RF_A

C

JIT

SPIN

DFCT

SCOR

GSCOR

EXCK

SBSO

WFCK

C2POMA9

MA9

JITO

FF

XSRQ

MNT1

GFS_DVD

MA1

0

XRST

D6D5 XINI

T1

XINI

T0

XCS1

882

XHW

R

XHRD

A7A5A4A3A2A1A0D7 A6

MDIN

MDIN

MDP

MA1

0

BCLK

MDAT

LRCK

16MBT D-RAM

DVD DECODER

BUFFER

BUFFER

1

2

3 4

8

5

67

BOARD

BOARD

(1/6)

(3/6)

BOARD BOARD

BOARD BOARD

(1/6) (3/6)

(6/6)(5/6)

BOARD

BOARD

BOARD

BOARD

(1/6)

(3/6)

(5/6)

(4/6)

BOARD(3/6)

BOARD(5/6)

BOARD(1/6)

DMB07

DMB07

DMB07

DMB07

DMB07

DMB07

DMB07

DMB07

DMB07 DMB07

DMB07 DMB07

DMB07

(Page42)

(Page42)

(Page42)

(Page42)

(Page44)

(Page44)

(Page44)

(Page44)

(Page45)

(Page46)

(Page46)

(Page46)

(Page47)

HCD-NXM4D

4444HCD-NXM4D

7-15. SCHEMATIC DIAGRAM – DMB07 (3/6) BOARD – • See page 65 for IC Block Diagram. • See page 74 for IC Pin Function Description. • See page 62 for Waveforms.

R906

R925R930

R907

L90147uH

IC902

CN901

FL901

C903

R905

R926

R901

R970

FL908

R984

R975

R923

FL903

X902 R927

C916

IC904

R908

C904

C924

C917

C907

R915

R974

R916

R988

R917

R994

R995

R997

R996

R998

R936

R990

C913

R911

R912

C909C908

R920

R943

R942

R940R921

C905

C910

C914

C915

R962

R958

R918

R902

C906

R978

R931

FB902R933

R932

FB903

C918

R938

R964

IC901

X901

IC906

R904

R935

C902

C901

R913

IC111

IC903

IC101

Q901

221/

10W

1001/10W

1001/10W

221/

10W

SN74AHC1G32DCKR

7P

0UH

1004V

221/

10W

1001/10W

221/10W

0

0UH

10k1/10W

10k1/10W

2201/10W

0UH

27MHz 1M1/10W

1004V

SN74AHC2G74HDCUR

10k1/10W

0.01

0.01

0.01

0.01

100 1/10W

0

1k 1/10W

0

1k 1/10W

0

0

0

0

0

100 1/10W

0

33000p

10k1/10W

10k1/10W

100p100p

100 1/10W

1001/10W

1001/10W

1001/10W

1001/10W

0.01

0.01

9p

7p

10k1/10W

221/10W

221/10W

221/10W

0.01

10k1/10W

221/10W

0UH22

1/10W

221/10W

0UH

0.01

10k1/10W

10k

CXP973064-245R

20MHz

SM8707GV-G-E2

10k1/10W

4.7k1/10W

0.01

1004V

10k1/10W

BR24L16F-WE2EEPROM

7P

DTC114TE-TLINVERTER

VMUTE

VIDEO _SW

BUS 5

ANALOG BUS

SPC970_BUS

DSP BUS

ZIVA_CTRL_BUS

D3V

DGND

768FS

A0A1A2A3A4A5A6A7

XINIT0

XINIT1

D0

D1

D2

D3

D4

D5

D6

D7

XCS1882

XHRD

XHW

R

CLK_

RF

DATA

_RF

SENS

XLAT

TXD

RXD

MD2

PI

JIT

TE

SLED

A

SLED

B

LOCK

FOK

SCLK

GFS_CD

SP_ON

SPFG

SLED

MUTE_2D

MUTE_CD

GFS_DVD

TSD-M

LDON

RST_SPC

I2C_

SIO

I2C_

SCL

SDEN

FE

SCOR

DRVR

X

DRVT

X

DRVC

LK

DRVI

RQ

DATA

CLOK

SQSO

SQCK

XRST

_CD

COUT

MIR

R

INLI

M

JITO

FF

DSAV

E

27M

SYS_

RST

DRVR

DY

DRVC

LK

CS_S

PC

CS_S

PC

WP

SCL

SCL

WP

SDA

SDA

MNT1

RXD

TXD

RF_AC

RFMON

I2C_

SIO

CDSP2

MRE

Q

JIG_MOD

XRSTI2

C_SC

L

LDSEL

FJMP1

FJMP2

768F

S

MECHANISM

CONTROLLER

SWITCHING

FLIP FLOP

CLICK

GENERATOR

SWITCHING

(FOR CHECK)

BOARD BOARD(1/6) (2/6)

BOARD BOARD

BOARD BOARD

(1/6) (2/6)

(6/6)(5/6)

BOARD BOARD

BOARD BOARD

(1/6) (2/6)

(5/6)(4/6)

BOARD(2/6)

BOARD(4/6)

DMB07BOARD(5/6)

DMB07DMB07

DMB07DMB07

DMB07

DMB07DMB07

DMB07DMB07

DMB07DMB07

DMB07

BOARD

MAIN

(1/3)

(Page42)

(Page42)

(Page42) (Page43)

(Page43)

(Page43)

(Page43)

(Page45)

(Page45)

(Page46)

(Page46)

(Page46)

(Page47)

(Page51)

HCD-NXM4D

4545HCD-NXM4D

7-16. SCHEMATIC DIAGRAM – DMB07 (4/6) BOARD – • See page 67 for IC Pin Function Description. • See page 62 for Waveforms.

FL205

R232

R240

Q202

R251

R10

R11

R244

IC207

R284

C229

C244

R268

R269

R217

R220

R219

R222 R221R225

R226

R228

R272

R271

R290

IC204

C241

C279

C242

R15

C248

R14

C252

R13

C278

C261

R12

R213

C263

C277

C265 C266 C283 C282 C267 C268 C269R257 R245

C272 C281

C270 C280 C271

R248

R234

R291 R292

R299

R246

C216R255

C247

R227

R247

C256

R230

R231

C290

C260

C262

C234C233C232C231C230C226

R259 R260

R254

R253

C236 C274 C276 C238

R805

R283

R261 R1000

C289

CN202

C253

C257

C204

C251

C237

CL255

0UH

331/10W

47k1/10W

DTC114TE-TL

0

221/

10W

221/

10W

1k1/10W

ZIVA5X-C2F

1801/10W0.5%

0.01

0.01

00 00 0

0 0 0

0

0

1001/10W

1001/10W

100

BR9040F-WE2EEPROM

0.01

100p

0.01

221/10W

0.01

221/10W

0.01

221/10W

100p

0.01

221/10W

68

0.01

100p

10 0.01 100p 100p 0.01 0.01 0.014.7k

1/10W4.7k

1/10W

0.01 100p

0.01 100p 0.01

4.7k 1/10W

10k 1/10W

100 100

8201/10W

10k1/10W

0.010

0.01

4.7k1/10W

1k 1/10W

0.01

331/10W

331/10W

100p

0.01

0.01

0.010.010.010.010.010.1

4.7k1/10W

4.7k1/10W

4.7k1/10W

4.7k1/10W

0.01 0.01 0.01 0.01

0

1k1/10W0.5%

4.7k1/10W

4.7k1/10W

0.01

4P

0.01

0.01

0.01

0.01

0.01

ZIVA_CTRL_BUS

DAC_CTRL_BUS

A3V-2

D5V

D3V

GND

CN105

EXT_SIGNAL_BUS

SAMBA_SIGNAL_BUS

PCM_5.1CH_BUS_A

VDD 4-5

B 4-5

HAD0

HAD1

HAD2

HAD3

HAD4

HAD5

HAD6

HAD7

HAD8

HAD9

HAD1

0

HAD1

1

HAD1

2

HAD1

3

HAD1

4

HAD1

5

DRVCLK

DRVIRQ

RST_SPC

I2C_SIO

I2C_SCL

HA1

SYS_RST

JIG_

MOD

CS_S

PC

AV7

AV6

AV5

AV4

AV3

AV2

AV1

AV0

XSRQ_ZIVA

XSAK#

SDEF#

XDCK#

ML

MC

MDI

MRE

Q

MRE

QM

REQ

27M

BCK

LRCK

XCK

I/P S

W

WID

E

WE

INT/EXT

DRVCLK

DRVTX

DRVRX

DRVRX

DRVTX

DRVRDY

119

122

125

128

131

MD31

MD30

MD29

MD28

MDQM3

MD27

MD26

MD25

MD24

MD23

MD22

MD21

MD20

MD19

MD18

MD17

MD16

MD15

MD14

MD13

MD12

MD11

MD10

MD9

MD8

MD7

MD6

MD5

MD4

MD3

MD2

MD1

MD0

MDQM2

MDQM1

MDQM0

MCLK

MWE

MA0

MA1

MA2

MA3

MA4

MA5

MA6

MA7

MA8

MA9

MCA

S

MRA

S

MA1

1

MA1

0

MCS

O

BA1

BA0

DATA

1

DATA

2

XCK1

BCK1

LRCK

1

DATA

3

DATA

0

HA3

HA2

ALE

CE

SYS_RST

DVD SYSTEM PROCESSOR

BOARD(1/6)

BOARD BOARD

BOARD BOARD

(1/6) (2/6)

(3/6) (5/6)

BOARD(3/6)

BOARD

(5/6)

BOARD(6/6)

BOARD BOARD

(5/6) (6/6)

DMB07

DMB07DMB07

DMB07DMB07

DMB07

(Page42)

(Page42)

(Page43)

(Page44)

(Page44)

(Page46)

(Page46)

(Page46)

(Page47)

(Page47)

HCD-NXM4D

4646HCD-NXM4D

7-17. SCHEMATIC DIAGRAM – DMB07 (5/6) BOARD –

FL203 FL204

R215

R250

R9980

R9981

R9982

R9983

R9984

R9985

R9998

R9999

C218

C220

C235

C240

C243

C246

C250

C258 C259

C264

C227

C239

C245

C249

C254

C255

R270

R274

R275

R276

R277

R273

CN105

IC206

R198

C287

C286

C205

C284

R197

R202

C203

C275

R282

R267

R281

R266

R280

R265

R264

R279

R263

R278

C291C215C214

D202

FL206

R301

IC203

IC232

IC233

C202

IC231

C201

R294

R296

R293

IC211

C213

IC259

IC258

IC256

Q201

0UH 0UH

0

0

0

0

0

0

0

0

0

0

0.01

0.01

0.01

0.01

0.01

0.01

0.01

10 0.01

0.01

0.01

0.01

0.01

0.01

0.01

10

0

0 0 0 00

17P

MBM29PL32BM90TN

4.7k1/10W

0.01

0.01

0.01

0.01

4.7k1/10W

47k1/10W

0.01

0.01

751/

10W

751/

10W

751/

10W

751/

10W

751/

10W

751/

10W

751/

10W

751/

10W

751/

10W

751/

10W

100p0.010.01

1SS355TE-17

0UH

1k

HY57V283220T6

SN74LV573APWR

SN74LV573APWR

0.01

SN74LV573APWR

0.01

0

0

0

1004V

SN74LV573ALATCH

SN74LV573ALATCH

SN74LV573APWR

DTC114TE-TLINVERTER

SIGNAL_BUS

EXT_SIGNAL_BUS

DGND

D3V

VMUT

E

VIDE

O_SW

VGND

V5VCN

105

GND

SAM

BA_S

IGNA

L_BU

S

VDD

4-5

B 4-

5

HA5

HA6

HA7

HA8

HA9

HA10

HA11

HA12

HA13

HA14

HA15

HA16

HA17

HA18

HA19

HA20

HA2

HA3

HAD0

HAD1

HAD2

HAD3

HAD4

HAD5

HAD6

HAD7

HAD9

HAD10

HAD11

HAD12

HAD13

HAD14

HAD15

HA21

MA0

MA1

MA2 MA3

MA4

MA5

MA6

MA7

MA8

MA9

MA10

HA1

HA4

MCAS

MRAS

MCSO

MA11

HA22

SD7

SD6

SD5

SD4

SD3

SD2

SD1

SD0

XSAK

SDEF

XDCK

XSHD

ADC_DATA

XSRQ

SYS_RST

HAD0

HAD1

HAD2

HAD3

HAD4

HAD5

HAD6

HAD7

HAD8

HAD9

HAD1

0

HAD1

1

HAD1

2

HAD1

3

HAD1

4

HAD1

5 HA1

HA2

HA2

HA11

HA10

HA9

HA8

HA7

HA6

HA5

HA4

HA19

HA18

HA17

HA16

HA15

HA14

HA13

HA12

HA22

HA21

HA20

ALE

119

122

125

128

131

I/P S

W

WID

E

CE

WE

BCK

LRCK

HAD8

INT/EXT

AV7

AV6

AV5

AV4

AV3

AV2

AV1

AV0

XSRQ_ZIVA

SDEF#

XDCK#

XSAK#

MD2

MD3

MD4

MD5

MD7

MD0

MD1

MD6

MDQM0

MWE

BA1

BA0

MDQM2

MD16

MD19

MD20

MD23

MD17

MD18

MD21

MD22

MD30

MD24

MD26

MD29

MD25

MD27

MD28

MD31

MDQM3

MCLK

MD14

MD9

MD10

MD13

MD8

MD11

MD12

MD15

MDQM1

LATCH

+1.8V REG

LATCH

LATCH

BOARDVIDEO

BOARD(1/6)

BOARD BOARD

BOARD BOARD

(1/6) (2/6)

(3/6) (6/6)

BOARD BOARD BOARD

BOARD

(1/6) (2/6) (3/6)

(4/6)

BOARD(2/6)

BOARD(3/6)

BOARD(4/6)

BOARD(4/6)

BOARD

(6/6)

DMB07

DMB07

DMB07 DMB07

DMB07 DMB07

DMB07 DMB07

DMB07

DMB07

DMB07

DMB07DMB07

DMB07

DATA LATCH

DATA LATCH

DATA LATCH

SDRAM

RAM

(Page42)

(Page42)

(Page42)

(Page43)

(Page43)

(Page43)

(Page44)

(Page44)

(Page44)

(Page45)

(Page45)

(Page45)

(Page47)

(Page47)

(Page49)

HCD-NXM4D

4747HCD-NXM4D

7-18. SCHEMATIC DIAGRAM – DMB07 (6/6) BOARD – • See page 66 for IC Block Diagram.

C392

C394 FL302JW392

C325

R313

R312

R311

R310

R306

R309

R305

R304

R303

R308

C321

R302

FL352

R362R328

R329

R335

R327

C302

C303

C304

C305

C306

C307

C308

C309

C323

C324

C322

FL303

C393

C367

C368

IC302

IC352

C363C364

C365C366

C352

C355

R353

R352C356

C357

IC392

R307

C326

R392 D394D393

D392

JW802

JW804

JW805

JW806

JW801

JW803

R314

D1303 D1304

C1302

R1302

2216V

2204V 0UH

01004V

10k1/10W

100 1/10W

100 1/10W

100 1/10W

2201/10W

2201/10W

2201/10W

2201/10W

2201/10W

2201/10W

1006.3V

2201/10W

0UH

10k1/10W

0

0

0

0

0.01

0.01

0.01

0.01

0.01

0.01

100p

100p

0.1

0.1

0.1

0UH

0.01

470p

470p

PCM1609KPTRD/A CONVERTER

PCM1800E/2KA/D CONVERTER

0.11006.3V

0.11006.3V

1006.3V

1006.3V

0

01

50V

150V

3.3V REGULATOR

2201/10W

0.01

101/10W

1SS355TE-17

1SS355TE-17

1SS355TE-17

0

0

0

0

0

0

221/10W

1SS355TE-17 1SS355TE-17

0.1

0

DAC_CTRL_BUS

EXT_SIGNAL_BUS

DGND

AUDIO_5V

AUDIO_AGND

PCM_5.1CH_BUS_A

MDI

MC

ML

ADC_

DATA

LRCKBC

K

XCK

DMX-

A

MCK-A

DATA1

XCK1

BCK1

LRCK1

DATA3

DATA2

DMX-A

MCK-A

BCK-A

LRCK-A

CSW-A

SLR-A

FLR-A

DATA0

FLR-A

SLR-A

CSW-A

BCK-A

LRCK-A

BOARD(1/6)

BOARD

BOARD

BOARD

BOARD

(1/6)

(2/6)

(3/6)

(5/6)

BOARD

(4/6)

BOARD

BOARD(5/6)

(4/6)

DMB07

DMB07

DMB07

DMB07

DMB07

DMB07

DMB07

DMB07

1

5

10

15

20

21

BOARDMAIN

(1/3)

(Page42)

(Page42)

(Page43)

(Page44)

(Page45)

(Page45)

(Page46)

(Page46)

(Page51)

HCD-NXM4D

4848HCD-NXM4D

7-19. PRINTED WIRING BOARD – VIDEO BOARD – • See page 29 for Circuit Boards Location.

P

CHASSIS

C

G

Y

G

COMPONENT OUT

114

2815

C1124FB1106

R1111

C112

5

C1123FB1104

R1107

R1110C1116

C110

9IC1101

R1108

FB11

05

C1121

C1122

R110

4

C111

7

FB1101

C1104

R1103

R110

2

R110

1

L1101

R110

9

R1105FB1102

C112

0

C1118

R1106

FB1103C1119

R111

2Q1

101 E

EP1102 CHASSIS

J1101

J1101

J1102

J1102

J1103

J1103

JW11

08

C111

0

EP11

01

JW11

07

JW11

02

C1105

JW1103

C110

6

C110

3

C110

8

C110

1

C110

2

C110

7

CN11

01

JW11

04

C111

5

C111

4

C111

1

C111

2

C111

3

LP11

02

LP1101

JW11

05

JW11

09

171

S VIDEO OUTVIDEO OUTPR/CRPB/CBY

11(11)1-862-076-

VIDEO BOARD

DMB07BOARD

(Page40)

2 3 4 5 6 7

A

1

B

C

D

E

HCD-NXM4D

4949HCD-NXM4D

7-20. SCHEMATIC DIAGRAM – VIDEO BOARD – • See page 62 for Waveforms.

R1101

C1120

R1104

R1106

R1105

R1107

R1108

R1110

R1112

R1102

J1103

C1108

C1102

C1101

C1103

C1106C1105

C1111

C1112

C1113

C1114

C1115C1107

FB1101

FB1102

FB1103

FB1104

FB1105

EP1102 EP1101

C1116

C1104

R1103

L110110uH

C1109

C1110

R1109

C1117 C1118 C1119

C1123C1124

C1121

J1102

J1101

C1125

Q1101

FB1106R1111

IC1101

C1122

CN1101

10k

0

75

75

75

75

75

10k

10k

100

3PJALCO

1 50V

1 50V

1 50V

1 50V

1 50V22 50V

1000 6.3V

1000 6.3V

1000 6.3V

1000 6.3V

1000 6.3V1 50V

0

0

0

0

0

0.1

0.1

10k

0.1

0

0

10010V

100

22p 22p 22p

22p22p

22p

0

DTC114EKASWITCH

075

MM1623BFBE

0

17P

BUFFERVIDEO AMP

(CHASSIS)(CHASSIS)

BOARDDMB07

(5/6)(Page46)

HCD-NXM4D

5050HCD-NXM4D

7-21. PRINTED WIRING BOARD – MAIN BOARD – • See page 29 for Circuit Boards Location.

11(11)1-861-417-

MAIN BOARD

R339

R338

R337

R340R333R330R336R332R335

R331R334

R201

R15

R213

R212

R262

R263

Q4R1

4R1

3

R12Q5

R10

R11

R9

Q3R7R8

R18

Q6

E

E

EE

E

E

R16

R17

R224R225

IC201R115R117

R167

R165

Q152

Q102EE

R166R116

R261

R211

R251

C253

C252

R210

R259

C260

R260

C259

C209

C210

R209

R252

R253

C203

R203

C202

R202

R208

C205

C255C2

21

C208

R207

R205

R204

R206

C206

C258

R258

R257

R255

R254

R256

R220

R221

C256

C223

R222

R223

R231

R232

Q270

E E E E E E E E

R271

R272 R270

R274

R273

R275

Q271

JR115

R325

R326

R324

Q323

C324

D322

Q321

E

E

E

E

E

E

R321

R322R323C322

D321

Q326

R327

R329

R328

R291

R292

R293

Q277

R288

R289

Q276

R290

R285

R286

Q275

R287

R282

R283

Q274

R284

R279

R280

Q273

R281

R276

R277

Q272

R278

JR108

Q23

Q26

R25

Q24

R26

R29 R28

R27

Q25 JR

107

JR10

9

JR106 1 6

R123

Q153

R159

R161R180 R160

E

E

Q140

R133

C351

C301

R162

C196

R129

R122

C131

R121

R132

R131

R151

C303

C353

R164

R163

C157

C160

R153

C158R154

R155

C161

IC101

R157

R156

R128

R158 Q1

51E

R124

C123

R125

R127

C174

C173

C110R105

C108

C107

R104R1

06R1

07

R189

R101

C111

R120

R188

R341

R342Q341

R343

R345

R344

Q342

Q343

JR11

7

R126

R108

Q101

R3 R1

R103

R2

Q1

JR118

R42

JR119

R5

R6

Q2R4

R45

Q29

Q30 R3

3

R35

Q32

Q31

R36

R34 R38

R37

Q33

Q34

C146R110 R1

30

Q103

R109

Q316

R314

R315

R317

R318

R320

R316

R319

Q314

R303R353

Q353 Q303

Q315

R113

R112

R114R111

R352

Q352

R302

Q302

Q301

Q311

R312

Q312

Q313

R311

R313

R351

Q351

R301

R79

R89

178

R98

Q22

Q21

E

E

E

E

E

E

E

EE

E

E

E

E

E

EE

E

E E

E

E

E

E

E

E

E

R22

R21 R23

JR26

1JR

120

L903

L902

R906

R905

R908

R907

R909

Q903

Q904R9

14Q9

06

R904

R903

R902

R901

Q902 E

E

E

E

L951C952

R959

R958

R957

JR12

1

IC951

1142815

R955

R969JR

7

JR112

JR111

R970

R956 C9

53

R952

JR10

4

R450

R242

R244

R243 R241

Q27

Q28

R145R142

R192

C191

R191

C193

C100 R194

R193

R195

C141

R141

R144C143 R1

43

R30

R31

R32Q141

R146

Q191

E EE

E

R196

R247R246

R451R452

111

R448

C383

R387

R385

JR11

0 R383

R381

R379

R377

R433

121

R378

R384

R386

R388

R440

R439

R438

R382

R380

R434

R435

R436

R437

R441R443R445

R455

R442R444R446

R447

JR44

9

R453R454

R416 R430

R429R415 R424

R427

R419

JR418

R423R425

R426

R420

R417

C416

R413

R411

JR105

C412

JR10

1R3

91Q3

91

E

E

R393 D3

92

13

R394

C411C410

R409

R406

JR1031

3031

50

51

100

80 81

R407

D391

R392

R396R405R403R402R401

R404

R395

D393

D394

R475

JR114

D202D201JR113

Q401

R187

D181

D183

R498

R186

R499

D182

R495

R494

D397

D395

D396

R412

R465 C4

63C475 R4

70

C476

R472

R474

R477

R476R473

R471

R414

R408

R410 R493

R479

R478

R466

R467R4

82R4

83R4

68

R469

R484 R4

86

JR10

2R4

90

R489

R485

R496

R492

C494

C495

R400

R497

C499

C497

D905

Q19E

E

Q20R19

R20R24

Q40

R40

JR123

JR122

JR124

JR125

D904

JR12

6

C148

C198

1

2425

4041

64 65

80

JR12

7

JR128

R347

IC401

C197

C147R3

04R3

54

C305

C355

R305

R355

C306

C356

C357

C307

R306

R356

R357

R307

R309

R359

C308

C358

Q104 E

E

Q154

R102

R152

R118

R168

R119

R169

R915JR

203

JR204

JR20

5

JR206

C150

JR131

JR13

2

C368

C369

C39

C36

FB50C3

8FB

80

FB34

FB54

FB84

C35

C40

C37

JR13

0

C366

C31

JR133

JW17

1

JW17

2

JW10

3

JW10

2

JW10

6

CN10

9

12

1213

JW108

JW12

9

JW13

0

JW12

5

JW15

8

JW16

6

JW16

5

Q324

JW110

JW274

JW10

9

JW11

3

JW11

4JW11

6

JW11

8

JW11

9

JW12

0

JW476

JW159

JW160

JW23

6

JW15

0JW

149

JW17

4

JW17

3

CN202

1 7 JW151

JW143

JW140

JW141

JW142

JW131

C277

C276

C275

C274

C273

C272

C270

JW13

8

JW137

JW15

4

JW12

6

JW12

7

JW12

8JW41

8

JW17

5

JW17

6

JW136JW13

3

JW13

2

JW13

4

JW14

4

JW14

5

JW14

6

JW14

8

Q322

JW27

6JW27

5

JW10

7

Q327

JW27

1

JW411

JW412

JW413

JW105

JW111

JW112

JW115JW117JW122JW123JW155

JW156

C239

JW279

C213

C263JW474

JW480

CN104

JW27

8

JW468JW281

JW284

JW420

C135C156

C134

C154

C163

C122

C159

C133

C132

C152

JW28

6

C151

JW28

7

C166

C167 CN

108

11

13

84

CN30

1

C352

C302

JW289

JW288

C121

C155

C162

C168

C165

C304

C354

C119

JW41

9

JW29

3

JW29

4

CN30

2

C117

C118C1

15

C129

C116

JW26

1

JW30

1C3

14

C315

JW30

2

T301

C313C3

11

C312

Q318

L311

Q317

JW304

JW34

0

JW45

4

C101

C102

C128

C106

C130

JW31

2

JW37

8

JW37

9

JW38

0

JW38

1

C103

C109

C112

JW33

3

C105

C104

JW33

2

JW331

C114 C1

13

JW36

7

JW36

8

JW36

9JW

360

JW35

9

JW35

8

JW36

4

JW36

1JW

370

C1

C124

C139

JW33

0

C390

JW32

8

C138

C137

JW314

JW31

3

C164

C136

JW31

1

JW31

5

C140

E

E

E

JW32

7

JW31

6

JW32

6JW32

4

JW42

8

JW34

1

CN102

JW393

JW47

2

JW47

1

JW31

0

JW27

0

JW26

9

JW26

8

JW26

7

JW26

6

JW24

6

JW179

JW170

C229

C228

CN11

0

115

214

JW163

JW164

JW162

JW167

JW168

JW169

JW177

JW178

JW22

5

JW18

0

JW18

1

JW18

2

JW18

3

JW18

4JW

188

JW18

7

JW18

6

JW18

5JW

196

C183

JW31

7

JW26

0 JW19

0

JW22

8

C498

JW392JW397

JW396

JW388

JW389

JW38

5

C2

JW395

JW362

JW39

4JW482

JW481

JW354

JW429

CN103

110

C22

C21

JW382

JW384

JW490

C916

JW90

4

JW500

JW90

3

C912JW375

JW374

JW365

JW373

JW371JW376

JW349

JW322

JW323

JW351

JW347

JW346

JW348

JW377

JW8

CN20313 1

CN30

4

JW475JW421

JW297

JW42

2

JW42

3

JW467

JW31

8

JW31

9

JW262

JW263JW264

JW265JW259

JW255 JW256

JW257

JW258

JW22

6

JW22

7

IC391

C393

C391

C392

X402

JW20

9

JW210

JW211

C417

JW212

JW208

JW18

9

JW206

JW101JW124

CN372

JW207

CN401(CHECK)

JW224

C384

JW19

2

JW19

1

JW46

6

JW25

4

JW25

3

JW25

1

JW25

2

C462

JW40

2

JW40

5

JW355JW356

JW357

JW6JW248

JW241

JW244

JW242

JW48

5

JW42

4

JW404

JW40

9

JW41

0

JW24

5

JW461

JW460JW459

JW458

JW457

JW494

JW24

7

JW21

7

JW21

8JW215

JW213

JW23

8

JW19

4

JW41

6JW19

5JW198

JW199

JW200

JW197

CN204

JW202

JW201

JW239C144

C142

C194

JW221

JW220

JW38

3

JW49

9

JW45

5

JW48

3

C192

JW229

JW230

JW231

JW232

JW233

JW234

JW235

JW426

JW43

5

JW243

JW9

JW7

JW425

CN11

2

15

JW41

4

JW46

4

C901

C902

JW49

2

JW43

3

IC901

JW448

C905C906

IC903

131313

JW43

4

C904

C903

JW436

JW489

IC902

Q901

E C B

JW432

C920

C919

JW431

JW447

JW496

JW450JW438

JW452

CN1017 1

JW44

3

JW44

4

JW49

8

JW44

9

C930

D901

C907 JW

440

14

JW46

5

IC90

4

JW90

1

L901

IC90

5IC

906

L904

JW44

1

D902

JW320

C900

JW49

7

JW902

JW45

3

JW445

JW493

JW161

JW442

LP101

JW900

EP90

1

JW463

CN30

3

JW27

7

12

1213

C127

C911

C915

C914

C910

C908

JW48

8

JW237

JW5

JW13

9

JW14

7

JW386

JW387

JW495

JW10

JW280

JW344

JW343

JW21

9

JW283

JW193

JW222

JW32

1

C125

C126

JW391

JW33

6

JW33

7

JW456

JW25

0

JW240

JW216

JW446

JW46

2

JW4

JW50

1

JW491

JW214

JW41

5

JW223

JW249

JW205

JW20

3

JW930

JW407

JW35

3

JW20

4

JW329

JW350

C271

CN201

11121

JW3

JW295JW

291

JW29

8

L301

L351

D903

JW33

8

JW334

JW33

5

JW325

JW306

JW417JW296

JW363

JW28

5

JW366

JW372

JW29

9

JW398

JW290

JW29

2

JW39

9

JW300

JW303

C169

C43

C224

C220

C254

C204

C207

C257C222 C251

C211

C261

C120

C170

C233

121

22 42

C6 C3E E EC5 C4 C238

C201

C212

C262

C19

C20

C226

JW27

2

JW911

JW961

JW40

8

JW406

JW308

X401

JW43

9

JW42

7

JW273

JW390

LP104

FB90

3

JW504

JW50

2JW

430

JW50

3

JW47

0

JW157

JW477

JW30

9

JW40

1JW

282

JW152

JW50

5

JW30

5

JW35

2

JW46

9

JW506

JW121

LP105

TM502

VIDEO(MD)

TUNER

OUT

IN

OUT

IN

L

R

(CHASSIS)

E2

B RELAY BOARD(Page38) N DMBO7 BOARD

(page40)

DVOL BOARD

(page56)

KDMBO7 BOARD

(page40)

HFRONT AMP BOARD

(Page58)

SWITCHINGREGURATORAC IN

JFRONT AMP

BOARD(pge58)

(CHASSIS)

IFRONT AMP BOARD

(pge58)

C VOL BOARD(Page56) O DMBO7 BOARD

(Page40)

E PANEL BOARD(Page54)

L SUR AMP BOARD(page60)

G HP BOARD(Page56)

TAPEMECHANISMDECK

L-CH

R-CH

L-CH

R-CH

HP901PB HEAD

HPR901REC/PB HEAD

HE901ERASE HEAD

15

15

2 3 4 5 6 7 8 9 10 11 12 13 14

A

1

B

C

D

E

F

G

H

J

I

Ref. No. Location

D181 D-7D182 D-6D183 D-7D201 C-7D202 C-7D321 C-11D322 C-11D391 C-6D392 C-7D393 C-7D394 C-7D395 D-5D396 E-5D397 D-5D901 H-3D902 H-3D903 A-10D904 F-2D905 G-4

IC101 G-8IC201 D-9IC391 C-6IC401 D-5IC901 F-3IC902 F-2IC903 F-3IC904 H-4IC905 H-4IC906 I-4IC951 D-3

Q1 H-7Q2 H-6Q3 E-9Q4 E-9Q5 E-9Q6 E-8Q19 F-10Q20 F-10Q21 I-5Q22 I-5Q23 E-8Q24 E-8Q25 E-8Q26 E-8Q27 B-3Q28 B-3Q29 I-6Q30 H-6Q31 I-6Q32 I-7

• Semiconductor Location

Ref. No. Location

Q33 I-7Q34 I-7Q40 E-8Q101 G-7Q102 D-8Q103 I-8Q104 I-8Q140 G-9Q141 B-2Q151 F-7Q152 D-8Q153 F-9Q154 I-8Q191 B-2Q270 B-8Q271 B-9Q272 B-9Q273 B-9Q274 B-9Q275 B-10Q276 B-10Q277 B-10Q301 H-9Q302 H-9Q303 I-9Q311 H-8Q312 H-8Q313 I-8Q314 I-9Q315 I-9Q316 I-7Q317 J-8Q318 I-8Q321 C-11Q322 C-11Q323 B-11Q324 C-11Q326 D-11Q327 D-11Q341 F-7Q342 F-7Q343 F-7Q351 H-9Q352 H-8Q353 I-9Q391 C-6Q401 D-7Q901 G-3Q902 F-3Q903 G-4Q904 G-4Q906 G-4

HCD-NXM4D

5151HCD-NXM4D

7-22. SCHEMATIC DIAGRAM – MAIN BOARD (1/3) –

C903

C902

C904

C901

R377

R378

R379

R380

R381

R382

R383

R384

R385

R386

R387

R388

C930

CN101

C912

L904100uH

100uH10uH

10uH

C915

FB903

R909

C905C906

R902

R903

R904

R25R26

R40

D201

CN202

D202

R275

R279

R281

R276

R278

R272

R282

R284

R285

R287

R288

R290

R291

R293

R201

R261

R259

R260

R210

R209

R211

R212

R262

R252

R257

R220

R258

JW900

EP901

Q270

Q271

Q272

Q273

Q275

Q276

Q277

Q24

Q23

Q40

Q26

Q25Q904

Q903

Q902 Q901

IC902

IC901

IC903

IC904

IC905

IC906

Q274

R225

R224

R203

R202

R213

R263

C262

C261

C212

C211

C213

C263

C201

C203

C259

C209

C238

C228

C229

C223

C207 C257

C255

C256

C222

C202

C260

C210

C252

C205

R253

R251

C253

R208

R207

R204

R205

R206

C206R254

R255

R256

R221

R222

C226

C224C220C254C258

C204C208

C251

C221

R223

R167

R117

Q102

Q152

R27

R29R28

R166R116

R165R115

C170C120

R274

C271

R280

R283C274

R286C275

R289C276

R292C277

R277C272

C273

C270

R270

R271

R273

C199

C149

C908

R901C233

C907

L901

C910C911

D902C916

C914

D901

D904R247

R246

CN204

CN372

C383

C384

L902

L903

JW901

JW904

JW902

R908

R906

R905

R907

CN201

IC201

R242

R244

R243

R241

CN203

C239

R231 R232

C900

1050V

10010V

10010V

0.150V

10k

10k

10k

10k

10k

10k

10k

10k

10k

10k

10k

10k

220016V

7PEH-S(2X)

10006.3V

33006.3V

LOW IMP

1.1UH

10k

0.150V

10010V

2.2k

2.2k

2.2k

22k100k

10k

1SS355

7P1MMFFC-S

1SS355

1k

2.2k

1k

2.2k

1k

1k

2.2k

1k

2.2k

1k

2.2k

1k

2.2k

1k

47k

47k

2.2k

2.2k

2.2k

2.2k

47k

1M 1M

470

47k

1k47k

2SC5938MUTE

2SC5938MUTE

2SC5938MUTE

2SC5938MUTE

2SC5938MUTE

2SC5938MUTE

2SC5938MUTE

DTA114EKAMUTE SWITCH

DTC114EKAMUTE SWITCH


DTA114EKAMUTE SWITCH





2SB1640LINE BUFFER

TA7809S

TA7809S

TA7805S

PQ12RD21

SI-8050JF

SI-8033JF

2SC5938MUTE

2.2k

1k

10k

470

0

0

1050

V10

50V

1050

V10

50V

1050

V

1050

V

1050

V

220p

0.00

1

0.00

110

016

V

0.22

0.1

0.00

1

1050V

1050V

0.00

1

0.00

1

1050V

220p

0.00

22

0.00

22

220p

0.00

110k

47k

220p

47k

47k

1k

10k

4.7k

0.0011k

10k

4.7k

10k

4.7k

150V

1050V

1050V

1050V0.022

1050V0.022

1050V

0.001

47k

10k

10k

2SC5938MUTE

2SC5938MUTE

6.8k

100k6.8k

47k47k

1k1k

1050V

1050V

10k

1050V

10k

10k1050V

10k1050V

10k10

50V

10k10

50V

10k1050V

1050V

1050V

2.2k

10k

2.2k

1050V

1050V

100016V

10k10016V

1050V

100016V

33006.3V

LOW IMP

RK36LF10006.3V

100016V

RK36LF

1SS35510k

10k

11P

21P

0.1

4706.3V

100

100

4.7k

22k

21P

M61530FP

100k

100k

13PPH-S

470

10V

10k 10k

680016V

M+9

V

D+3.

3V

M-G

ND

AUDI

O+9V

EVER

+4V

UNRE

G+5V

UNRE

G+12

V

BUS

ANAL

OG-IN

-R

ANAL

OG-IN

-L

MUT

ERL

GND

+3.3

V

MUT

E

AUDI

O+9V

M+9

V

BUS

M-G

NDGND

C-OU

T

SL-O

UT

SR-O

UT

DM-L

FL-IN DM

-R

FR-IN

SL-IN

SR-IN

C-IN

LFE-

IN

DM-L

DM-R

FR-IN

C-IN

SL-IN

SR-IN

LFE-IN LFE-IN

SR-IN

SL-IN

C-IN

FR-IN

FL-IN

DM-R

DM-L

DM-R

FR-IN

C-IN

SL-IN

SR-IN

LFE-

IN

DM-L

SWSURR

-R

SURR

-L

50

43

27

28

12

28

51

52 53 54 55

A5

SW-O

UTR-OU

T

L-OU

T

FL-O

UT

FR-O

UT

65

4833473446454442 35363741 38394075

FL-IN

FL-IN

302926252423

*

*

+9V REGULATOR

+9V REGULATOR

+5V REGULATOR

+12V REGULATOR

+5V REGULATOR

+3.3V REGULATOR

BASS BOOST

LPF,AGC

INPUT ATTENUATOR

BOARDMAIN

(3/3)BOARDMAIN

(2/3)

SWITCHING

REGULATOR

BOARD

BOARD

AC IN

FRONT AMP

BOARD

BOARDBOARD

DMB07

DMB07DMB07

TUNER

RELAY

(CHASSIS)

E2*241,243

10k E2

0 EXCEPT E2

(3/6) (6/6)

(1/6)

(Page39)

(Page52)

(Page59)

(Page53)

(Page42)

(Page47)(Page44)

HCD-NXM4D

5252HCD-NXM4D

7-23. SCHEMATIC DIAGRAM – MAIN BOARD (2/3) –

R110

Q351

Q352Q302

Q301

C313

Q317

R315

R320

Q318

Q315

Q311

L311100uH

L301

L351

CN301

R341

Q341

R342

R343Q342

R345

R323R326

Q322

Q327

R329

R336

R333

Q353Q303

R169

R119

Q104

Q154

Q32

Q31

Q30

Q29

R359

R309

R338

R339

R337

R132

R131

C122

Q34

CN304

R307

R357

R102

R152

R118

R157

R156

R158

C139

R107

R106

R108

R196

R146

Q141

R195

R145

Q28

R31

Q27R30

Q191

R155

C126

C127

C125

R301

R302

R351

R352

R316

R318

R355R305

R319

Q316

R314

T301

Q314

Q312

R311

Q313

R313

R312

Q321

Q326

CN302

C140

C303

C353

C35

C150

C356

C306

C355

C357

C308

C358

C307

C305

C315

C314

C312

C311

C322C324

C369

C123

C368

C40

Q323

Q324

D322

Q343

Q33

R304 R354

C137

C164

C163

C113

C114

C115

R112C117

R113

C147

C197

R163

C167

C148

C198

C118R114

C119

C166 R161 R180

C196

R159

R160

C168

R164C169R162

C102 C128

C101 C129

C130 R1

20

C103

C104

C105

R101

C106 C1

07

C108

C110

R104C109

C111

C112

R103

R105

IC101

R109 C146

R130

C161C159R154R153

R129

C134

C152 C151

C165

C135

R123

C162C160

C158

C157

C155

R151

R121

C121

C131

C138

C124

R143

R193 C193

C143C191

C141 R142

R192R144

R194 C194

C144C192

C142

R125R124

C154

R133

C136

R128

R344C390R37R38

R347

C156

R331

R334

R340

R335

R332

R330R324R325R327R328

C133

R122C132

R356

R306

C354

C304C352

C302

C351

C301FB30 FB50

FB80

FB34

FB54

FB840uH

0uH

0uH

0uH 0uH

0uH

R34C43

R33

R43

R35R36

D321

R321R322

CN303

R32

R126

C173

C174

Q101

Q151

Q140

Q153

Q103

J101

C38

R303R353

R317 R168

R111

C116

R127

R141

R191

1k

2SC3624A

2SC3624A2SC3624A

2SC3624A

4710V

RT1P137LBIAS SWITCH

4.7k

33

2SC2001BIAS SWITCH

DTC114EKA

2SA812

27mH

27mH

3PPH-L

10k

2SC1623AMS BUFFER

4.7k

22kDTC114EKA

AMS BUFFER

10k

1k1k

2SB1116

2SB1116

47k

47k

47k

2SC3624A2SC3624A

10k

10k

2SC5938TC REC MUTE

2SC5938TC REC MUTE

DTA114EKATC REC MUTE

DTC114EKATC REC MUTE

DTA114EKATC PB MUTE

DTC114EKATC PB MUTE

2.2k

2.2k

10k

47k

22k

27k

2.2k

4.750V

DTA114EKAAMS MUTE

3P MOLEX

10k

10k47k

47k

100

330

10k

47k

1 50V

330

10k

47k

1k

1k

2SC5938MUTE

1k

1k

DTA114EKAREC OUTMUTE SW

22k

DTC114EKAREC OUTMUTE SW

0

2SC5938MUTE

10k

100 10V

100 10V

100 10V

4.7k

4.7k

4.7k

4.7k

10

47

4.7k4.7k

3.3k

DTC114EKABIAS SWITCH

47k

SUMIDA

DTA114EKA

DTC114EKA

10k

DTC114EKA

10k

10k

DTC114EKA

DTC114EKA

8PPH-L

150V

330p

330p

0.1

0.1

100p

100p

0.001

330p

0.01

0.01

330p

0.001

0.0047

0.01

0.01

0.0068

0.00470.0047

0.1

0.1

0.1

0.1

DTC114EKA

2SB1116

1SS355

DTC114EKAAMS BUFFER

DTC114EKAAMS MUTE

15k 15k

0.47

0.47

0.47

0.47

0.47

1050V

12k 1 50V

330k

100p

100p

330k

1 50V

100p

100p

0.01180

4716V

1050V

1k 100

0.0068

47k

1k

0.01

1804716V 12k

1050V

1050V

1050V

0.47

0.04

7 10k

1050

V

1050

V

0.1

15k

1050

V

0.02

2

0.02

2

0.04

7

2.2k1050V 0.0056

1050V

2.2k

10k

M61537FP

47k 0.0068

100

0.00561050V

2.2k2.2k

15k

1050V

1050V

1050V

1050V

150V

1M

1050V

0.04

7

0.02

2

0.02

2

0.115

k

2.2M

1

22p

0.22

10010V

1k

1k 220p

220p220p

220p 100k

100k100k

100k 1050V

1050V 10

50V

1050V

4.7k4.7k

1050V

10k

1050V

1M

10k2250V100k22k

2.2k

1050V

47k

47k

4.7k

47k

4.7k

4.7k2.2k2.2k2.2k2.2k

0.01

15k

0.01

8.2k

8.2k

1050V

1050V

1050V

1050V

330p

330p

22k2.250V

BIPOLAR 100k

4.7k

100k22k

1SS355

2.2k2.2k

13P

100k

10k

100p

100p

2SC1623BUFFER

2SC1623BUFFER

2SC5938AMS MUTE

2SC5938PB MUTE

2SC5938PB MUTE

4P

0.1

1k1k

10k

100

1k

1050V

10k

10k

10k

BUS

ANALOG-IN-L

ANALOG-IN-R

L

R

GND

TC D+3.3V

M-GND

AUDIO+9V

MIC SIG

IC101

DBFB

M+9V

MUTE

MUTE

GND

M-GND

M+9V

AUDIO+9V

BUS

FR

FL

89

A12

90

A11

91

A10

88

100

86

FL-O

UT

FR-O

UT

R-OU

T

L-OU

T

SW

SURR-L

SURR-R

87

B18

B19

C32

80

81

63 B17

A18

INPUT SELECT SWITCH

Q351-353

REC/PB SWITCH

REC/PB SWITCH

Q311-315

Q301-303,

BOARDMAIN

(1/3)

BOARDMAIN

(3/3)

TAPE MECHANISM

DECK

HEAD

HP901PLAYBACK

R-CH

L-CH

L-CH

R-CH

HEAD

ERASEHE901

HEAD

PLAYBACK

HRP901

RECORD

DECK B

DECK A

R

L

OUT

IN

R

L

VIDEO(MD)

(CHASSIS)

(FOR CHECK)

ELECTRICAL VOLUME

(Page51)

(Page53)

Q321-324,326,327TC MOTOR SWITCH

HCD-NXM4D

5353HCD-NXM4D

7-24. SCHEMATIC DIAGRAM – MAIN BOARD (3/3)– • See page 76 for IC Pin Function Description. • See page 62 for Waveforms.

R407

R423

R424

R426

R425

R483

R411

R413

R409

R417

Q391

D391

R393 D394

R498

R499

R494

R495

D396D395

R453

R454

R455

R465

R1R439

R438R437

R436R435

R434R433

R443

R442R441

R440

CN401

R486

R489R490

R956

R957

R958

R959

R450

R451

R452

R446

R447

R955

R485

R484R448

R445

R444

R952

Q906

C919C920

R482

CN112

W606

R15

R10

R12

R7

R9

R16Q6

R17

R18

R4

R42

R45

Q22

R22

R21

C22

Q20

Q19

R19

R20

R24

C20Q21

CN103R4

19

R420

R427

R406

R404

JW46

0

JW45

9JW

458

JW45

7JW

456

JW46

1

R970

R969

JW5

IC401

X401

IC391

R395

D393

R914

D905

CN110 CN109

R915

CN108

CN102

L951

C497

C412

C37

C31

C39

C391

C952

R400

R475

Q401

R416R415

R430

R429

JR418

IC951

JR449

R478

R477

R476

R479

R493

R474

R473

R472

R471

R470

R469

R468

R467

R466

R410

R408

R414

R412

C476

C475

X402C411C410

Q2

Q1

JW961

R89

JW911

R79

D182

R187

R186

D183

D181R188

R189

C463C462

JW3

C3

R8

Q3

Q5

C5

R14C4 R13

Q4

R11

C6

R5

C2

R2R3

R6

C1

C19C21

R23

C417

C416

R394D392

R396C393

R392 C392

R391

C183

JR7

R497

C499

R496R492C953

D903

D397

C498

CN104

100

100

100

100

100

100

330k

0

10k

10k

2SC1623RESET

1SS355

22k 1SS355

10

10

3.3k

3.3k

1SS3551SS35510

010

0

100

100

2.2k100

100100

100100

100100

100

100100

100

4PAMP-S

100

100100

100

100

100

100

100

100

100

100

100

100

100

100100

100

100

100

2SC1623+3.3V REGULATOR

1050V

1050V

100

5P1.25MMFFC-S

WIRE

1k

2.2k

1k

2.2k

1k

2.2k2SC5938

MUTE

10k

1k

2.2k

100k

100k

DTA114EKATA MUTE

22k

4.7k

2250V

DTA114EKASW MUTE

DTC114EKASW MUTE

15k

22k

100k

4.750V5L

DTC114EKATA MUTE

10PB-TO-B

0 4.7k

10k

100

100

10k

10k

M3062CMEN-A01FP

32.7

68kH

z

M62703

220

1SS355

1k

UDZS-TE-17-3.9B

15P1.25MMFFC-S

13P1.25MMFFC-S

1k

4PAMP-L

8PB-TO-B

0

0.1

0.1

0.1

0.1

0.1

0.1

0.1

10k

100

DTC114EKAMIC SWITCH

10k10k

100

100

0

PT8300R

0

100

100

100

100

100

100

100

100

100

100

10k

10k

10k

10k

10k

10k

10k

10k

0.01

0.01

16MHz18p18p

2SC5938MUTE

2SC5938MUTE

0

0

1SS355

470k

0

1SS355

1SS355470

47k

0.110010V

1050V5L

10k

2SC5938MUTE

2SC5938MUTE

1050V5L

10k10

50V5L

2.2k

2SC5938MUTE

10k

1050V5L

10k

1050V

10k1k

1k

1050V

4.750V5L

2250V 100k

22006.3V

0.1

4.7k1SS355

10k10

50V22k 0.1

10k

2.250V

0

10k

0.1

0.1

10EDB40

1SS355

1050V

6PAMP-S

BUS

M+9V

D+3.3VAUDIO+9V

EVER+4V

UNREG+5V

UNREG+12V

GND

M-GND

TC D+3.3V

MIC SIG

IC101

DBFB

MUTE

+3.3V

GND

M-GND

MUTEM+9V

AUDIO+9V

BUS

23 24 25 26 27 28

4

69 686766

A19

A20

A21

A22

A23

FL

FR

SR-OUT

SL-OUT

C-OUT

SW-OUT

71727476777879

4

94 70

A23

A22

A21 73

86

8788

8990

91

A10

A11

82838485

100

A8

A9

B21A8

C7

B20

A17

50

3334

3536

3738

3940

4142

4344

4546

4748

A12

A17

A9

1 2

A20

A19

A5

C6

A24

3

3

29 30

C6 C7

B22

95

A18

C32

C19

C19

A24

94

95

8384

85

82

80

81

66676869 657374777879 76 717275 70 63

B22

B21

B20

B19

B18

B17 5152535455

**

I/O EXPANDER

SYSTEM CONTROL

LEVEL DETECT

BOARDMAIN

BOARDMAIN

(2/3)

(1/3)

BOARDVOL

BOARDVOL

BOARDPANEL

(FOR CHECK)

BOARDHP

BOARD

BOARD

BOARDFRONT AMP

FRONT AMP

SUR AMP

*R492

1k E24.7k EXCEPT E2

4.7k

*R496

3301k

1.5k

0

E3,E15EA

AUSE2

TH,SP,MY

(Page51)

(Page52)

(Page57)

(Page57)

(Page55)

(Page57)

(Page61)

(Page59)

(Page59)

HCD-NXM4D

5454HCD-NXM4D

7-25. PRINTED WIRING BOARD – PANEL BOARD – • See page 29 for Circuit Boards Location.

R1096

R102

0

IC1020

Q102

6R1

037

R103

6

R1034

R1024

R1023

R1021

C102

5

R1025

C1021C1022C1023C1024

C104

8

R102

7R1

028

R103

2R1

029

R103

0R1

031

C102

9

R104

5

R105

1C1052

C1050 R1052

R104

6D1022

Q1024

Q1022

Q1023

R104

1

R1042

R110

2

R110

1

R104

3Q1021 R1100

D1023

R103

3

R103

5R1

040

D102

4

D102

5

D102

6

C1054

R1038

R103

9

R1022

R102

6

C1006

JW1020

JW1022

JW1032

JW1033

JW1034

JW1035

JW1037 JW10

23

JW1021

JW1050

JW10

39

JW10

49

JW1071

JW1043

JW10

40 JW1081

C1053

CN1021

T801

C1051

S1036

S1030

S1032

S1034 +

–

S1035

S1031

S1029 b B

z START

CD

TAPE A/B

CD SYNC

TUNING

ALBUM

DIMMER

DISPLAY

TUNER/BAND

VIDEO(MD)

X

x

CD Z

M>

.m

D1021

S1021

S1022

S1023

S1024

S1028

S1025

S1026

S1027

C102

8

C102

6

JW10

25

JW10

48JW10

24

JW1026

JW1027

FL1020FLOURESCENT INDICATOR TUBE

JW10

36

JW10

45JW

1046

JW1029JW1030

JW1031

1

5 4

1E 3

510

1520

2530

3540

4550

5556

60

JW1038

JW10

47

JW10284849

1716

33 32

64 1

JW10

41

JW10

42

S1033

L1021

LP1001

PANEL BOARD

11(11)1-861-474-

MAIN BOARD

(Page 50)

E

E

E

E

2 3 4 5 6 7 8 9 10

A

1

B

C

D

E

F

G

Ref. No. Location

D1021 B-1D1022 B-2D1023 B-3D1024 B-2D1025 B-2D1026 B-2

IC1020 B-6

Q1021 B-4Q1022 B-5Q1023 A-5Q1024 A-2Q1026 B-1


HCD-NXM4D

5555HCD-NXM4D

7-26. SCHEMATIC DIAGRAM – PANEL BOARD –

R1046

R1052

C1048

L1021

Q1024SWICHING

REGULATOR

R1045

C1053

C1050

R1020

C1028

R1039 R1040R1038R1036 R1037

R1034 R1035R1033

R1025C1025

R1023R1022

C1021

R1021

R1024

R1043 R1042 R1041

R1102R1101R1100

C1029

R1027R1026 R1028 R1030R1029 R1031R1032

S1021 S1022 S1023 S1024 S1025 S1026 S1027S1028 S1029 S1030 S1031

S1032 S1033 S1034 S1035 S1036

FL1020

CN1021

R1051

C1051

C1052

C1006C1026

IC1020

Q1024(1/2)

Q1024(2/2)

Q1021 Q1022 Q1023

Q1026

D1022 D1023

D1025

D1024

D1026

D1021

T801

C1054

10k

100

R10962.2k

0.135V

3.3k

2250V

0.01

100

1050V

10k 33k4.7k1.5k 2.2k

4.7k 10k2.2k

10k220p

100100

0.001

C1022100P

C1024

100P

C102

3

100P

1k

1k

100k 100k 100k

10k10k10k

0.1

330220 470 1k680 1.5k2.2k

13P

10022050V

0.01

0.110

50V

M66005-0131AHPRBOT

CPH5504-TL-E

CPH5504-TL-E

2SC1623 2SC1623 2SC1623

DTC114EKALED SWITCH

RD6.2FM 1SS355

1SS355

1SS355

1SS355

SEL5423

DC-DC CONVERTER

22000p

36 35

343332313029

2726252423222120

19181716151413121110987654321

50494847464544434241

39 38

28

40

37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3536

37 51 52

/START(MD)

VIDEODISPLAY TAPE A/BTUNER/BANDCD DIMMER CD SYNC

/KEY CONTROLDISPLAY CONTROL

DRIVEGRID

Q1021-1023

LIQUID CRYSTAL DISPLAY

(3/3)(Page 53)

HCD-NXM4D

5656HCD-NXM4D

7-27. PRINTED WIRING BOARD – DISC SW, VOL, HP BOARD – • See page 29 for Circuit Boards Location.

g

R1049

R1094

C1001R100

1R1

002

Q1001

C1002

R100

3R1

004

R1011

Q1002

R1012

C1003

R1005R1006

Q1003

R1013R1014

C1004

R100

7R1

008

Q1004

C1005

R101

0

R100

9

R1095

C1016

D1051

R1059 Q1041

R1048R1050

R1093

R1092

R1054

R1091R1090

Q1005E

E

E E

E

C1008

C1007

1

10

C1009

JW10

51

JW10

52

JW10

53

JW1002JW1003 JW1004

W1001

NO1001

JW1076

D1001D1002D1003D1005 D1004

CN1051

S1043

D1050

CN1050

S1004S1005DISC 5

VOLUMEDSGX

S1052

SOUND SELECTS1051

SOUND MODES1050

DISC 4 DISC 3 DISC 2 DISC 1

S1003 S1002 S1001

JW10

56

JW10

55JW

1054

JW1057

C1013

IC1050 S1042

JW10

58JW

1059JW

1078

JW1073

JW10

69

JW10

77

NO1052

JW10

01

DISC SW BOARD

VOL BOARD

11(11)1-861-475-

11(11)1-861-476-

MAIN BOARD

(Page 50)C

MAIN BOARD(Page50)

D

1

10

1 2 3

E

HP BOARD

IC1061

C1061

R1061

R106

2

C106

6

R106

0R106

4

R1063

C1063

C106

4

R106

6C1

067

R106

5

C107

0

R106

9C1

071

R107

0

R1068

IC1060

R107

3

R1071

R1074

R107

5

R1072

D106

1

R107

9

R1077

R108

0

C108

6

C1084

R108

1

R1082

R1083C108

5

C1091

C108

8 C109

0

C1079 R1076

R108

6R1

085

R107

8

C109

2

C1087R1084

R1067

R108

8

JR10

81

JR1080

C109

4

C1093

C1095

C1089

C1096FB1001

FB1003FB1004

FB10

02

FB10

10FB

1011

EP10

60

CHASSIS

EP10

61

CN10

60

CN10

62

J1063

JW10

97

JW1099

JW10

75

JW10

72

JW10

98

JW10

83

JW10

70

JW1079

C107

7

C106

8

C107

8

C106

0

C106

2

C106

9C1

073

C108

3

C108

2C1

076

C107

2C107

4

JW10

06

JW1066JW1068

JW10

80

JW10

61

JW1060

C108

0

JW1063

JW1067JW10

62

JW10

85

JW1082

JW1086

JW1088

JW10

64

JW1084

JW1074

GMAIN

BOARD

FFRONT AMP

BOARD

PHONES

J1060MIC1

J1061MIC2

RV1060MIC LEVEL

RV1061ECHO LEVEL

(Page 50)

(Page 58)

11(11)

1-861-477-

116

89

1

45

8

\/1

2 3 4 5 6 7 8 9 10 11

A

1

B

C

D

E

F Ref. No. Location

D1001 B-6D1002 B-5D1003 B-4D1004 B-3D1005 B-2D1050 D-6D1051 D-5D1061 C-9

IC1050 D-5IC1060 D-9IC1061 C-9

Q1001 B-5Q1002 B-5Q1003 B-4Q1004 B-3Q1005 B-2Q1041 D-6


HCD-NXM4D

5757HCD-NXM4D

7-28. SCHEMATIC DIAGRAM – DISC SW, VOL, HP BOARD – • See page 66 for IC Block Diagram.

R1012R1011 R1013 R1014

R1049

R1050

D1050

C1013R1059R1090

R1091

R1092

R1093

R1094R1095

R1048

S1050

S1042

CN1051

CN1050

D1051

NO1052

Q1001 Q1002 Q1003 Q1004 Q1005

Q1041

S1001 S1002 S1003 S1004 S1005

IC1050

S1043

R1062C1066

R1065

R1066

C1067

R1064C1064R1063C1071

R1067

C1070

IC1060(1/2)

IC1060(2/2)

C1063

C1088

C1086

C1085

D1061

R1069

R1070

RV1060

R1068

C1079

R1082

R1083

R1084

R1078

C1087

C1092

R1086R1085

R1073

R1071

R1072

R1074

R1061

R1060

R1075

EP1060

C1090 C1091

JW1006

C1095

C1062 C1068

C1077

C1069

C1073

JW1099 JW1098C1096

CN1062

R1081R1080

C1082

R1079

C1072

RV1061

C1083

C1089

C1084

C1076J1061

C1074

J1060

CN1060

R1088 JR1081

JR1080

J1063

C1093

C1094

FB1001

FB1002

IC1061

FB1010

FB1011

C1060

EP1061

C1061

R1077

C1080

C1078

R1076

R1001

R1002 R1003

R1004

R1005

R1006

R1007

R1008

R1009

R1010

D1001 D1002 D1003 D1004 D1005

C1001 C1002 C1003 C1004 C1005

NO1001

S1051 S1052

330220 470 680

1k

220

SEL5223S

4716V

471k

1k

1k

1k

1k1k

2.2k

5P

15P

1SS355

10P

DTC114EKALED DRIVE

DTC114EKALED DRIVE

DTC114EKALED DRIVE

DTC114EKALED DRIVE

DTC114EKALED DRIVE

DTC114EKA

NJM24M400A

1k 47p

1k

47k

220p

100k0.00110k47p

100

100p

NJM4565M

NJM4565M

0.01

0.001

0.001

0.0068

UDZSTE-175.1B

150k

100

50k

10k

0.022

22k

22k

47k

22k

0.1

0.0068

22k22k

100k

10k

10k

0

10k

1k

10k

0.47 0.47

0.1

0.2250V

0.2250V

1.050V

2.250V

2.250V

1000p

3PAMP-L

22k120k

4716V

220

1035V

50k

4716V

0.068

0.068

1035V

22010V

4PAMP-L

0 0

0

0.001

0.001

FB

FB1003FB

FB1004FB

FB

M65850FP-E

FB

FB

0.2250V

0.01

15k

150V

2.250V

15k

1k

1k 1k

1k

1k

1k

1k

1k

1k

1k

SEL5823A SEL5E23C SEL5E23C SEL5E23C SEL5E23C

0.1 0.01 0.01 0.01 0.01

10P

1 2 3 4 5 5

43

21

7

12

34

56

7

8

910

1112

89

1011

12

1234 56

I/ REMOTE

CONTROLRECEIVER

SWITCH

Q1001-1005LED

SWITCHLED

(CHASSIS)

(CHASSIS)

(CHASSIS)

DIGITAL

ECHO

MIC AMP

MICVOL

ECHO

LEVEL

MIC 1

MIC 2

BOARD

BOARDMAIN

FRONT AMP

(3/3)(Page53)

(3/3)BOARDMAIN

(3/3)BOARDMAIN

SOUND SOUND

SELECT MODE

1

2

3

4 5

6

7

8

(Page53)

(Page53)

(Page59)

HCD-NXM4D

5858HCD-NXM4D

7-29. PRINTED WIRING BOARD – FRONT AMP BOARD – • See page 29 for Circuit Boards Location.

2 3 4 5 6 7 8 9 10

A

1

B

C

D

E

F

G

H

11(11)1-861-478-

FRONT AMP BOARD

C537 C538

C540C539

R577

C546D510

R554

D508

R555

R556

R557

D850

D851C858

R862

R863

R864Q8

61

R866

R867

R865

C857

R502

R503

C502

R510

R511

R512

R527

22 1

R517

R518

R519

Q501

Q859

Q860

Q502E

E

E

D506

C545

D502 D503

D852

R582

R586

R589

Q510

R574

R575

C557

C513

R559

R522

R523

Q503

D501

R560

Q509

E

E

D507

Q851E

E

D505

Q852

Q850 E

R851

R850

IC850

R506

R509

D504

R505

C503

R507

C504

R871

R872

Q868

E

E E

E

E E

Q869

R564

R565

R860

D509

R890

Q890

R538

R540 R5

30

R535

R513

C507

R516 R515

C508 C511

R539

R534R5

31

R533R532

R567

R568R569

C541

C543C544

C529

C542

C547C548

Q507

R547

R545

R548

Q508

R546

R549

R550

R876

R875

Q853

1

13

4

Q854

EE R854

R857

R870

D853

R880

R562

JW504

R561

R566R563

JW505

R578

JW507

R576

R584

L504

JW509

R583

L505JW514

R591

R590

EXCEPTEA

EXCEPTEA

EXCEPTEA

EXCEPTEA

EXCEPTEA

EXCEPTEA

EA

EA

EA

EA

EA

EA

EAEA

EA

JW511

R585

TH53

1

C534

C535

L501

L502

L503

EP502

R587

TM40

2

L506

C531

C530

RY50

2

JW562

C526

C527

JW608JW

673

CN508CN501

C501

IC501

JW653

C506 C509 C510

C860

C859

JW654

TM50

2

TM502

R525

R526

R541

JW601

R580

JW678

JW61

0

LP502

LP503

LP504

RY50

1

C853

1 3

6 4

C525

C524

C852

C851

C861

C854

C856

C523

R524

C522

C855

C862

R542

R543

JW680

JW681

JW682

JW621

JW688

JW61

8

JW61

7

JW57

4

JW616

JW615

JW614

JW612

JW613

JW689

JW61

9JW62

3

JW549

JW632 C528

Q505E

E

E

E

C560

C505

JW583

JW66

4

C850

JW605

JW607

JW627

JW606

JW683

JW684

JW603

1

11

JW675

JW593 JW674

JW597

JW651 JW591JW521

JW638JW635

JW634

JW63

6

JW59

4JW

637

JW553

CN50211 1JW691

JW584Q858

EJW640

JW609

JW56

7

JW67

1

JW67

2

JW66

1

JW60

4 JW600

JW66

6

JW64

5

JW64

6

JW64

8

JW65

8

JW652

JW64

9

JW65

0

R520

JW668

JW669

E

JW692

JW58

1

JW580

R544JW579

C516

JW65

7

R521

JW687

JW58

2

JW63

0

JW62

9

JW62

8

JW693

JW663

JW58

5

JW68

6

R581

JW626

JW670

Q504

Q506

C515

JW58

8JW

590

R529

R536

R855

R858

CN505

JW639

JW665

JW56

4

JW56

5

JW69

5

JW561

JW56

3

JW66

0

JW690JW

696

JW69

7

JW69

8

CN50

7

CN50

3

JW57

8

JW57

7

JW685 JW676

JW625

CN50

6

31

C518

C865 R570

R571

R572

R573

JW520

JW595

JW596

R595

R599

R598

JW655

FHP BOARD(Page56)

M962DC FAN

IMAIN BOARD

(Page50)

JMAIN BOARD

(Page50)

MSUR AMP BOARD

(Page60)

H MAIN BOARD(Page50)

M961DC FAN

+

+-

-

+

+-

-

+

+-

-

SPEAKER

S.WOOFER

CENTER

FRONT R

SURR R

FRONT L

SURR L

Ref. No. Location

D501 F-2D502 C-4D503 C-4D504 E-3D505 E-3D506 E-2D507 D-2D508 G-5D509 G-5D510 F-4D850 B-4D851 A-5D852 B-5D853 C-4

IC501 C-4IC850 F-2

Q501 E-2Q502 E-2


Ref. No. Location

Q503 E-2Q504 E-3Q505 E-3Q506 E-2Q507 E-4Q508 D-4Q509 G-4Q510 G-4Q850 F-3Q851 F-3Q852 F-3Q853 B-2Q854 B-2Q858 B-2Q859 B-5Q860 B-5Q861 B-4Q868 B-4Q869 B-4Q890 B-4

HCD-NXM4D

5959HCD-NXM4D

7-30. SCHEMATIC DIAGRAM – FRONT AMP BOARD –

C503

R507 C504

Q851

Q852

R505

R506

R530

R531

D504

R535

R534

D505

R545

R546

R550

R547

R851

R850

R559

R564

R565

D509

C850

C513

C852

C853C851C854

C855

C856

R855

R858R875

R876

R509

R860

Q850

R890

R536

R542

R543

CN505

R532

R533

R870

R871C861

C862

C530

C531

C534

C535

R555 R556R554 D508

R571

R572 R573

R598

R599 R596

R595

C529

R562

R566

R578

C537 C538

C539 C540

C541 C542R577

R581

R587

R584

R586

C545 C546

C543 C544

C547 C548

R589

R539

R538

R540 R544D506

D507C526

C527R541

R516

C509

R511 R518R519

Q501

Q502

TH531

C516

R515

R512

C515

D503

D502

D501

C510

C501

R502

C508C507 C511

C502R503

C560

C505

CN501

CN508

R527

C860

R862

R867

R866C859

R863

R865

D852

R864

Q859

CN506

CN507

R880

D853

C865

CN502

CN503

R591

Q853

Q854

R520

R526R525

R524

R521

JW520

R528

R513

R560

R580

C557

R872

IC501

Q505

Q506

Q504

R529

C522

C523

C524

C525

R549

Q507

Q508

Q510

Q509

Q890

Q869

Q868

R510

C506

R537

Q503

C528

C857

C870

D851

C858

D850

Q861

Q860

IC850

R568 R569R567

Q858

L504

L505

R585

L506

JW511

R590

JW509

JW514

R583

R582

JW507

R576

L503

R563

L502

R561

L501

JW504

JW505

R570

EP502

R574

R575

D510

RY502

R517

R523

R522

C518

R548

RY501

R557

R854

R857

470p

47k 470p

2SC1623

2SC1623

1k

47k

1k

15k

1SS355

1k

15k

1SS355

2.2k

47k

2.2k

68k

4.7k

2.2k

2.2k

47k

47k

1SS355

1050V

0.001

2.250V

22010V100

10V10

50V

4.7100V

4.7100V

6802W

6802W

220

220

1k

4.7k

2SC1623

10k

0.22 2W

101/2W

101/2W

4PAMP-L

100k

100k

4.7k

22k10010V

10010V

220050V

220050V

220035V

220035V

22k 22k22k ISS355

1.8k2W

1.8k2W

1.8k2W

4.7k1/2W

4.7k1/2W

4.7k1/2W

4.7k1/2W

0.01

10

1/2W

101/2W

101/2W

100000p 100000p

100000p100000p

100000p 100000p47k

1001W

10

1/2W

101/2W

47k

100000p 100000p

100000p 100000p

100000p100000p

47k

1k

15k

100k 101/2W

1SS355

1SS3550.150V

0.150V

0.225W

47k

4716V

150 100k

100k

2SC1623

2SC1623

MT

4750V

33k

150

4750V

UDZS

-TE-

17-1

5B

UDZS

-TE-

17-1

5B

1SS355

4716V

1050V

1k

220p220p 220p

470p47k

10 50V

10 50V

8PB-TO-B

10PB-TO-B

47k

4.750V

22k

4.7k

47k47

16V

22k

100

1SS355

220k

2SC1623

3PEH-L

3PEH-S

22k

1SS355

2250V

11PSCN-L

11P

101/2W

2SC3624AMUTE

2SC3624AMUTE

1001/4WFR

1.5k1/2W

1.5k1/2W

11/4W

RF

1001/4WFR

47k

10k

1001W

0.001

100k

STK413-420

2SC1841OVER LOAD

DETECT

2SC1841OVER LOAD

DETECT

2SC1841OVER LOAD

DETECT

0.222W

0.1100V

0.1100V

0.1100V

0.1100V

2.2k

2SA1163G-TE85LSTK MUTE SW

2SC1623STK MUTE SW

2SC1623RELAY SWITCH

2SC1623RELAY SWITCH

DTC114EKA

DTC114EKA

DTA114EKA

330

4716V

2SC2713G-TE85L-VH SUPP

47100V

0.01

0.01

UDZS-TE-17-6.8B

0.01

UDZS-TE-17-6.2B

DTC114EKA

2SC1623

RT8H015C

68k 47k68k

2SD2525

101/2W

101/2W

101/2W

47k

101/2W

101/2W

101/2W

1.8k2W

2.2k

10k

1SS355

12V

47k

33k15k

100100V

5.6k

12V

4.7k

1k

1k

-

+

-

+

-

+

-

+

-

+

-

+

RELAY DRIVEPROTECT

Q850-852

(SPEAKER)

POWER AMP

PROTECTEROVER CURRENT

Q501,502OVER HEAT

DETECT

Q868,869,890MUTE

CONTROL

Q858-861

FAN MOTOR DRIVE

M961

FAN

FAN

TM502

M962

SPEAKER

EA

EXCEPT EA

EA

EA

EA

EA

EA

EA

EXCEPT EA

EXCEPT EA

EXCEPT EA

EA

EA

EA

BOARDMAIN

BOARDMAIN

BOARD

BOARDMAIN

BOARDSURR AMP

HP

(CHASSIS)

(3/3)

(3/3)

(1/3)

(Page53)

(Page53)

(Page57)

(Page61)

(Page51)

HCD-NXM4D

6060HCD-NXM4D

7-31. PRINTED WIRING BOARD – SUR AMP BOARD – • See page 29 for Circuit Boards Location.

11(11)1-867-087-

SUR AMP BOARD

C650

R661

R662

R663

C603

R616

R626

C607

R604

R602

R607

R621

R635

C611

R612

D511

D512

R603C602

R608

C606R613C610

Q610

E

E

EE

R652

R653

R609

R614

C622

R627R628

D603

R629

R622

R623

R658

D602

D604

R617

R618

R657

D601

C623

JW602

JW605

JW607

JW608

JW609JW610

JW61

1

JW614JW615JW616

EP602

JW620

JW621

JW61

2

JW606

JW603JW604

JW613JW60

1

JW62

3

JW62

2

NO60

31

11

JW624

LP601

R605

R610R615

C604

C601

C605

R656

R670

C609

R620

C617

C624

Q602

C608

C612

Q601

Q603

C620

IC601 1 15

C621

R681

R630

C614

C618

R680

R625

CN60

11

6

RY602

RY601

EP601LP602

C615

JW619

LMAIN

BOARD(Page50)

M FRONT AMP BOARD(Page58)

2 3 4 5 6

A

1

B

C

D

E

Ref. No. Location

D511 B-3D512 B-3D601 C-3D602 B-3D603 B-3D604 C-3

IC601 D-3

Q601 C-3Q602 C-2Q603 B-2Q610 B-3


HCD-NXM4D

6161HCD-NXM4D

7-32. SCHEMATIC DIAGRAM – SUP AMP BOARD –

C601R602

C605R607

R612

C623

CN601

R616

R670

R621

R626

R604 R609

C622

C604 C608

C650

R658

R629

R622

R623

R627

R628

R625

R630

R610

R657

R617

R618

R620

D604

RY601

RY602

R652

D512

D511

R680

R681

R662

R661

R663D602

D603

D601 R653

R635

R615

C621

C620

C618

C617

NO603Q610

Q601

Q602

Q603

EP602

EP601

C612

R614

R613

R608

C602 R603

IC601

C624

R656

C614

C615

C606

C610

C607C603 C611

R605

C609

2.250V 1k

2.250V 1k

1k

0.01

6PCT-L

47k

11/4WRF

47k

47k

560 430

0.001

4710V

4710V

0.01

100k

100k

1k

15k

1k

15k

101/2W

101/2W

0.222W

100k

1k

15k

101/2W

1SS355

12V

12V

10k

1S355

1SS355

1001W

1001W

47k

68k

68k

1SS355

1SS355

1SS355 2.2k

10k

0.222W

0.1

0.1

0.1

0.1

11P

2SC3624ARELAY

SWITCH

2SC1841PROTECT

2SC1841PROTECT

2SC1841PROTECT

4710V

430

47k

47k

470p 47k

STK403-240ASURROUND AMP

2250V

1001/4W

FR

0.1

0.1

470p

470p

100p100p 100p

0.222W

2.250V

(CHASSIS)

(CHASSIS)

BOARD

BOARDMAIN

FRONT AMP(3/3)

(Page53)

(Page59)

HCD-NXM4D

6262HCD-NXM4D

• WAVEFORMS

– MAIN BOARD –

IC401 0 XC-IN

VOL/DIV : 0.5 V ACTIME/DIV : 2.0 µsec

2 IC401 qd X-OUT

VOL/DIV : 0.5 V ACTIME/DIV : 50 nsec

1

1.5Vp-p

32.768KHz

1.5Vp-p

16MHz

– DMB07 BOARD –

IC701 170 XTL1

VOL/DIV : 2 V ACTIME/DIV : 20 nsec

2 IC901 r; XTAL


7 IC207 119 VDAC_4

VOL/DIV : 0.5 V ACTIME/DIV : 20 µsec

1

5.2Vp-p

33MHz

3.2Vp-p

20 MHz

0.7Vp-p

H

3 IC906 8 XTO


3.4Vp-p

27 MHz

4 IC509 el FE

VOL/DIV : 0.1 V ACTIME/DIV : 2 msec

0.1Vp-p

5 IC509 ra TE


0.1Vp-p

6 IC509 t; RFAC

VOL/DIV : 0.5 V ACTIME/DIV : 0.1 µsec

1.1 Vp-p

8 IC207 122 VDAC_3


9 IC207 125 VDAC_2


1.1 Vp-p

1H

0 IC207 128 VDAC_1

VOL/DIV : 1 V ACTIME/DIV : 20 µsec

0.8 Vp-p

qa IC207 131 VDAC_0


1.2 Vp-p

qs IC207 139 X IN


4Vp-p

15.3 MHz

0.7 Vp-p

H

qd IC207 148 LRCK


3.3Vp-p

47 KHz

qf IC207 149 BCK

VOL/DIV : 1 V ACTIME/DIV : 0.2 µsec

3.2 Vp-p

1.5MHz

– RF BOARD –

IC001 1 DVD RFP


2 IC001 el TE


1

0.7Vp-p

1.8Vp-p

3 IC001 r; FE


0.3Vp-p

4 IC001 tj RFAC


1.2Vp-p

– VIDEO BOARD –

IC1101 0 CY IN


2 IC1101 qs CB IN


7 IC1101 wa Y OUT


1

2Vp-p

H

3 IC1101 qf CR IN


4 IC1101 qh CR OUT


5 IC1101 qk CB OUT


6 IC1101 w; CY OUT


8 IC1101 wd CVBS OUT


9 IC1101 wh C OUT


0 IC1101 2 C IN


qa IC1101 6 Y IN


1Vp-p

H

0.7Vp-p

H

0.7Vp-p

H

1.5Vp-p

H

1.5Vp-p

H

2Vp-p

H

2.6Vp-p

1.8Vp-p

1Vp-p

1Vp-p

H

63

HCD-NXM4D

7-33. IC Block Diagram

– RF Board –

IC001 SP3723CAFOPM

MUX ATT INPUTBIAS AGC

GCA

PROGRAMMABLEEQUALIZER

FILTERDIFFERENTIATOR

64 63 62 61 60 59 58 57 5156

12

FULL WAVERECTIFER

AGC CHARGEPUMP

+–

+–

++

+++

+

++

++

––

+–

+–

INPUTSEL ATT

2

4

2

2

INPUTIMPEDANCE

SEL

OFFSETCANSEL

MNTRCONTROL

SERIALPORT

REGISTER

4FROM

S-PORT

4FROM

S-PORT

INPUTIMPEDANCE

SEL

3FROM

S-PORT

CLAMP &ENVELOPE

LEVELDACSIGDET

AGCO

BUFFER

55 54 53 52 50 49

OUTPUTINHIBIT

FROM S-PORT

3

4

5

6

78

9

10

11

12

13

14

15

16

17

GCA

CD/DVD

4FROM

S-PORT

3FROM

S-PORT

MUX

3FROM

S-PORT

GCA

3FROM

S-PORT

3FROM

S-PORT

EQ

VC

COMPARATOR

PHASEDETECTOR

PHASEDETECTOR

A+D

B+D

++

A+C

B+C

GCAW/LPF

SUMAMP

18 19 20 21 22 24 2523 26 27 28 29 31 3230

GCAGCA

VCI FOR SERVO INPUT

VC = VPB/2

DUAL APC

LD H/LFROM S-PORT

APC SELDVD/CD

TOPHOLDGCA

TOPHOLD

GCA

41

48474645

GCAOFFSETCANSEL

5FROM

S-PORT

GCA 40

GCAOFFSETCANSEL

6FROM

S-PORT

3FROM

S-PORT

GCAGCA

CEFDBCP/CNLOW

IMPEDANCE

CD/DVD

SUBGCAMUX GCALPF

GCALPF

39

38

3736

OFFSETCANSEL

PEAK/BOTTOMHOLD

BOTTOMENVELOPE

INPUTBUFFER

5FROM

S-PORT

GCALPF

V25/2

TERST

35

34

33

FOR SERVOOUTPUT

PH

TOPHOLD

GCASEL

LINKEN

MUX

HOLDEN

+–

+–

COMPA-RATOR

INTERNALFDGHG

HYSTERESISTER& OFFSET

FROM S-PORT

MIRRCOMPARATOR

INPUT GAINFROM S-PORT

SEL

DAC

SINK CURRENTFROM S-PORT

2

AGCO

FAST ATTACK

AGCHOLD

BCADET

2FROMS-PORT

PH

2

2

INPUTIMPEDANCE

FROM S-PORT

4443

42

V33 FOROUTPUTBUFFER

PIFETECE

V25V125

V25/3

LPF ATTPOL SELBUFFER

CONTROLSIGNALSTO EACHBLOCK

3CE ATTCEPOL

D

C

B

A

CD F

CD E

VPB VC

DVDL

DCD

LD

CDPD

DVDP

D

LDONVN

B

MIR

R

MP

MB

MIN

MEV

O

MLP

F

CE

SDENSDATASCLKV33

FE

TE

PI

V25V125

TPH

DFT

LINK

LCPLCN

MNTR

DVDRFPDVDRFN

A2

B2

C2

D2

CPCN

D

C

B

A

CD D

CD C

CD B

CD A

RFDC

RFSI

N

ATOP

ATON

AIN

AIP

VPA

RFAC

VNA

BYP

DIN

DIP

FNP

FNN

MEV

RX

64

HCD-NXM4D

– DMB07 Board –

IC509 CXD3068Q

DOUT

LRCKPCMD

BCK

DVDD2ASYEMD2

EMPHXTSL

DVSS2XTAI

XTAO

SQSOSQCKSCSYSBSOEXCK

SOUTSOCKXOLT

SETEVCTES1TEST1DVSS1FRDR

FFDR

TRDR

TFDR

SRDR

SFDR

DVDD1FSTOSSTP

MDPLOCKPWMI

FOKDFCT

DIGITALCLV

PROCESSOR

OSC

DIGITALOUT

EFMDEMODULATOR

32KRAM

ERRORCORRECTOR

D/A DIGITALINTERFACE

MIRR, DFCT,FOK

DETECTORCPU

INTERFACE

SUBCODEPROCESSOR

SERVOAUTO

SEQUENCER

SERVO INTERFACE

DVDD

0

XRST

MUT

E

DATA

XLAT

CLOK

SENS

SCLK

ATSK

WFC

KXU

GFXP

CK GFS

C2PO

SCOR C4M

WDC

KDV

SS0

COUT

MIR

R

AVDD

0IG

ENAV

SS0

ADIO

RFDC

CE TEAVSS

1RF

ACAS

YIAS

YO

BIAS

AVDD

1PC

OFI

LIFI

LOCL

TV

V16M

VCTL

VPCO

59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

2122

232425

262728

29

30

31

32

33

34353637383940

8079787776

757473

7271706968

676665

64

636261

OPER

ATIO

NAL

AMPL

IFIE

R &

ANAL

OG S

WIT

CH

A/D

CONV

ERTE

R

FOCUSPWM

GENERATORTRACKING

PWMGENERATOR

SLEDPWM

GENERATOR

FOCUSSERVO

DSPTRACKING

SERVODSPSLED

SERVODSP

ASYMMETRYCORRECTOR

DIGITALPLL

CLOCKGENERATOR

60

– DMB07 Board –

IC706 MSM51V18165B-60TSKR1

NC

A9 A8 A7 A6 A5 A4 VSS

A11

A10 A0 A1 A2 A3

VDD

VDD

DQ0

DQ1

DQ2

DQ3

VCC

DQ4

DQ5

DQ6

DQ7

WE

RAS

3132 2930 262728

2019 2221 24 25232

VDD

1 43 65 87 109

VSS

DQ15

DQ14

DQ13

DQ12

VSS

DQ11

DQ10

DQ9

DQ8

4950 4748 4546 4344 4142 35

I/OSE

LECT

OR

OUTPUTBUFFER

INPUTBUFFER

OUTPUTBUFFER

INPUTBUFFER

SENSEAMPLIFIER

COLUMNDECODERS

MEMORYCELLS

WORDDRIVERS

ROWDECODERS

ON CHIPVBB GENERATOR

ON CHIPIVCC GENERATOR

COLUMNADDRESSBUFFERS

LCAS

34

UCAS

33

OE

I/OCONTROLLER

I/OCONTROLLER

17 1811 – 16

NC

40 – 36

ROWADDRESSBUFFERS

INTERNALADDRESSCOUNTER

REFRESHCONTROL

CLOCK

TIMINGGENERATOR

VCC VDD

VDD

VDD

65

HCD-NXM4D

– DMB07 Board –

IC903 BR24C16F-WE2

8VCC

7WP

6SCL

5SDA

1 A0

2 A1

3 A2

4 GND

ADDRESSDECODER

SLAVE WORDADDRESS REGISTER

DATAREGISTER

16 K bit EEPROM ARRAY

CONTROL CIRCUIT

POWER SUPPLYVOLTAGE DETECTION

HIGHT VOLTAGEGENERATOR

11 bit 8 bit

11 bit

STOPSTART

ACK

– DMB07 Board –

IC906 SM8707GV-G-E2

VDD1

VSS1

MO1

NC

REFDiv.1

PHASEDETECTOR1

PHASEPUMP1

LPF

LOOPDiv.1

X'talOSC

CONTROLLOGIC

NC16

NC15

NC14

SO313

VDD312

VSS311

SO210SO19

4

3

VDD2

VSS2 6

XTI 7

XTO 8

5

1

2

VCO

66

HCD-NXM4D

– DMB07 Board –

IC302 PCM1609KPTR

SYSTEMCLOCK

MANAGER

FUNCTIONCONTROL

INTERFACE

SERIALINPUT

INTERFACE

4X/8XOVER SAMPLING

DIGITALFILTERWITH

FUNCTIONCONTROLLER

ENHANCEDMULTI-LEVELDELTA-SIGMA

MOJULE

ZERO DETECT

DAC LPF

DAC LPF

DAC LPF

DAC LPF

DAC LPF

DAC LPF

DAC LPF

DAC LPF

RST

SCKISCKO

BCK

TEST

VDD

DGND

DATA1DATA2DATA3

ZEROA

LRCK

37

3839

40

42

43

44

454647

48

41

ZERO

1/GP

O1

ZERO

2/GP

O2

ZERO

3/GP

O3

ZERO

4/GP

O4

ZERO

5/GP

O5

ZERO

6/GP

O6 NC NC

VOUT

6

VOUT

5

VOUT

4

VOUT

3

1 2 3 4 5 6 7 8 9 10 11 12

VOUT2

VOUT1

VCOM

VOUT7

AGND5VCC5AGND6

VOUT8

AGND4VCC4AGND3VCC3

13

14

15

16

171819

20

21222324

ML

MC

MDI

MDO

ZERO

8DA

TA4

ZERO

7

NC VCC1

AGND

1

VCC2

AGND

2

36 35 34 33 32 31 30 29 28 27 26 25

– RELAY Board –

IC701, 711 BA6956AN

1 2 3 4 5 6 7 8 9

CONTROL LOGIC

TSD

VREF

OUT2

OUT1

RNF

VM VCC

FIN

GND

RIN

– HP Board –

IC1061 M65850FP-E1

OSCILLATOR

1/2 VCC

AUTORESET

LPF1

MAINCONTROL

A/D

20KBITSRAM

LPF2D/A

1 2 3 4 5 6 7

891014 13 12 11

CLOCK

RESETMO

MID1 DO0

DO1

VCC

CLOC

K

REF

OP2I

N

OP2O

UT

LPF2

IN

LPF2

OUT

LPF1

IN

LPF1

OUT

OP1O

UT

OP1I

N

CC1

CC2

GND

67

HCD-NXM4D

• IC Pin Function Descriptions• IC207 ZIVA5X-C2F (DVD SYSTEM PROCESSOR) (DMB07 BOARD)

Pin No. Pin Name I/O Description

1 VDDP — Power supply terminal (+3.3V) (I/O signal)

2 HA1 I/O Address bus

3 to 11 HD15 to HD7 I/O Data bus (address signal multiplexed)


13 GNDP — Ground terminal (I/O signal)

14 to 19 HD6 to HD1 I/O Data bus (address signal multiplexed)



22 HD0 I/O Data bus (address signal multiplexed)

23 HDTACK I/O Acknowledge signal input/output for host data transfer (not used)

24 HIRQ0 I Interrupt signal input for Medusa (not used)

25 WEH.UDS I/O Host upper data strobe signal output (not used)

26 WEL.LDS I/O Host lower data strobe signal output (not used)

27 HREAD I/O Read/write strobe signal output (not used)

28 GPIO0 I/O Jig detection port (pull-up)

29 GND — Ground terminal (inside core)

30 VDD — Power supply terminal (+1.8V) (inside core)

31 GND25 — Ground terminal (SDRAM I/O signal)

32 VDD25 — Power supply terminal (+3.3V) (SDRAM I/O signal)

33 to 42 MA9 to MA0 O SDRAM address bus



45, 46 MA10,MA11 O SDRAM address bus

47 BA1 O SDRAM bank select 1 signal output

48 BA0 O SDRAM bank select 0 signal output

49 MCS0 O SDRAM chip select 0 signal output

50 MCS1 O Not used

51 MRAS O SDRAM row address strobe signal output

52 MCAS O SDRAM column address strobe signal output

53 MWE O SDRAM write enable signal output (“H” : read, “L” : write)



56 MCLK O SDRAM Clock output

57 to 60 MD0 to MD3 I/O SDRAM data


62 MDQM0 O Byte read /write mask signal 0 output













68

HCD-NXM4D








105 VCLK I/O System clock (not used)

106 XCK_I/O_SEL I/O 5.1ch/downmix switch signal output (not used)

107 VS O S1 signal output

108 I/P SW O Progressive/interlace switch signal output

109 CDSEL O CD-DA selection signal output

110 MREQ O Audio muting request signal output



113 MDI O Serial data output to the D/A converter

114 MC O Serial data clock output to the D/A converter

115 ML O Latch enable signal output to the D/A converter

116 HIRQ2_ I Busy signal input from the EEPROM

117 VDAC_4B — Video DAC bias bit 4 (connected to the ground)

118 VDAC_VDD4 — Power supply terminal (+3.3V) (Video DAC 4)

119 VDAC_4 O VDAC output 4













132 VDAC_DVSS — Ground terminal (Video DAC digital system)

133 VDAC_DVDD — Power supply terminal (+3.3V) (Video DAC digital system)

134 VDAC_REFVDD — Power supply terminal (Video DAC reference)

135 VDAC_REF I Reference voltage input terminal(for Video DAC)

136 VDAC_REFVSS — Ground terminal (Video DAC reference)

137 XVSS — Ground terminal (crystal oscillator)

138 XOUT O Crystal oscillation signal output

139 XIN I Crystal oscillation signal input

140 XVDD — Power supply terminal (crystal oscillator)

141 AVSS2 — Ground terminal (analog PLL)

142 AVDD2 — Power supply terminal (+3.3V) (analog PLL)

143 AVDD1 — Power supply terminal (+3.3V) (analog PLL)

144 AVSS1 — Ground terminal (analog PLL)



147 XCK O Audio system clock output


69

HCD-NXM4D


148 LRCK O LRCK signal output for audio

149 BCK O BCK signal output for audio

150 DATA0(DM) O Audio data(Down Mix signal) output

151 DATA1(FLR) O Audio data(Front L/R signal) output



154 DATA2(SLR) O Audio data(Rear L/R signal) output

155 DATA3(CSW) O Audio data(Center/Subwoofer signal) output

156 IEC958 O S/PDIF signal (not used)

157 DAI_DATA I Data input from ADC (not used)

158 DAI_BCK I BCK signal input from ADC (not used)

159 DAI_LRCK I LRCK signal input from ADC (not used)

160 I2C_CL I/O I2C clock bus

161 I2C_DA I/O I2C data bus

162 CS(ZIVA_E2P) O Chip select signal output to the EEPROM

163 RXD1 I Serial data input for check jig

164 TXD1 O Serial data output for check jig

165 WRITE_CTRL(ZIVA_E2P) O Write control signal output to the EEPROM



168 SDDATA7 I SDBus data7 input










178 SDREQ O SDBus data request signal output

179 SDEN I SDBus data enable signal input



182 SDERROR I SDBus data error signal input

183 SDCLK I SDBus data clock input

184 HIRQ1 I Interrupt signal input from the mechanism controller

185 DRVCLK I Serial data clock input from the mechanism controller

186 DRVTX I Serial data input from the mechanism controller and the EEPROM

187 DRVRX I Serial data output to the mechanism controller and the EEPROM

188 DRVRDY O Ready signal input from the mechanism controller

189 VNW — Power supply for 5V tolerance voltage input

190 ALE O Latch enable signal output for address data demux

191 RST_SPC O Reset signal output to the mechanism controller

192 INT/EXT O Input selection signal output for SDBus or ADC (not used)

193 HCS2 O Chip select signal output for Medusa (not used)

194 HCS1 I/O Not used

195 HCS0 O Chip select signal output to the external ROM


197 TRST I Reset signal input

70

HCD-NXM4D


198 TDO O Data output

199 TDI I Data input

200 TMS I TMS signal input

201 TCK I TCK signal input

202 RESET I ZIVA reset input

203 BUS CLK I/O Not used



206 HA3 I/O Address bus 3

207 HA2 I/O Address bus 2


71

HCD-NXM4D

1, 2 D5, D6 I/O Two-way data bus with CXP973064-245R

3 VSS — Ground

4 D7 I/O Two-way data bus with CXP973064-245R

5 A0 I Address signal input from CXP973064-245R

6 VDD — Power supply (+3.3V)

7 A1 I Address signal input from CXP973064-245R

8 VDD5V — Power supply (+5V)

9 to 14 A2 to A7 I Address signal input from CXP973064-245R

15 VSS — Ground

16 XWAIT O Not used

17 XRD I Read strobe signal input from CXP973064-245R

18 XWR I Write strobe signal input from CXP973064-245R

19 XCS I Chip select signal input from CXP973064-245R

20, 21 XINT0, XINT1 O Interrupt signal output to CXP973064-245R


23 XHRS I Not used

24 HDB7 O Stream data signal output to ZIVA5X-C2F

25 VSS — Ground

26 HDB8 O Error flag signal output to ZIVA5X-C2F


28 VDDS — Power supply (+5V)

29 HDB9 O Not used


31 HDBA O Not used


33 VSS — Ground

34 HDBB O Not used



37 HDBC O Not used



40 HDBD O Not used


42 VSS — Ground

43 HDBE O Not used


45 HDBF O Not used

46 XSAK O Serial data effect flag signal output to ZIVA5X-C2F

47 VDDS — Power supply terminal (+5V) (digital system)

48 XDCK O Serial data transfer clock signal output to ZIVA5X-C2F

49 XSHD O Header flag signal (Not used)


51 REDY O Not used

52 VSS — Ground

53 XHAC I DVD mode: Serial data request signal input from ZIVA5X-C2F

54 HINT O Not used (Pull up)

55 XS16 O Not used (Pull up)

56 HA1 I Not used (Pull up)

57 XPDI I/O Not used (Pull up)


• IC701 TMC57929PGF-RDP (DVD DECODER) (DBM07 Board)

72

HCD-NXM4D



59, 60 HA0, HA2 I Not used (Pull up)

61 VSS — Ground (open)

62, 63 HCS0, HCS1 I Not used


65 DASP I/O Not used

66 to 69 MDB0 to MDB3 I/O Two-way data bus with the D-RAM

70 VSS — Ground

71 MDB4 I/O Two-way data bus with the D-RAM


73 to 75 MDB5 to MDB7 I/O Two-way data bus with the D-RAM

76 XMWR O Write enable signal output to the D-RAM


78 XRAS O Row address strobe signal output to the D-RAM

79, 80 MA0, MA1 O Address signal output to the D-RAM

81 VSS — Ground

82 to 87 MA2 to MA7 O Address signal output to the D-RAM


89 MA8 O Address signal output to the D-RAM

90 VSS — Ground

91 MA9/MNT0 O Address signal output to the D-RAM

92 MNT1/MNT1 O EEPROM ready signal output to CXP973064-245R

93 MNT2/MNT2 O Address signal output to the D-RAM

94 XMOE O Output enable signal output to the D-RAM

95 XCAS O Column address strobe signal output to the D-RAM

96, 97 MDB8, MDB9 I/O Two-way data bus with the D-RAM

98 VSS — Ground

99 MDBA I/O Two-way data bus with the D-RAM


101, 102 MDBB, MDBC I/O Two-way data bus with the D-RAM


104 to 106 MDBD to MDBF I/O Two-way data bus with the D-RAM

107 GFS O Guard frame sync signal output to CXP973064-245R

108 VSS — Ground

109 APEO O Absolute phase error signal output


111 DASYO O RF binary signal output

112 GNDA5 — Ground

113, 114 ASF1, AFS2 — Filter connected terminal for selection the constant asymmetry compensation

115 DASYI I Analog signal input after integrated from the RF binary signal

116 RFDCC I Input terminal for adjusting DC cut high-pass filter for RF signal

117 RFIN I RF signal input from the DVD/CD RF amplifier

118, 119 VCCA5, VCCA4 — Power supply (+3.3V)

120 VCOR1 — VCO oscillating range setting resistor connected

121 VCOIN I VCO input

122, 123 GNDA4, GNDA3 — Ground

124 LPF5 O Signal output from the operation amplifier from PLL loop filter

125 VC1 I Middle point voltage (+1.65V) input

126, 127 LPF2, LPF1 I Inverted signal input to the operation amplifier from PLL loop filter

73

HCD-NXM4D


128, 129 VCCA3, VCCA2 — Power supply (+3.3V)

130 PDO O Signal output from the charge pump for phase comparator

131 PDHVCC I Middle point voltage input terminal for RF PLL

132 FDO O Signal output from the charge pump for frequency comparator

133, 134 GNDA2, GNDA1 — Ground

135 SPO O Spindle motor control signal output to FAN8035L

136 VC2 I Middle point voltage (+1.65V) input

137 MDIN2 I Spindle motor servo drive signal input

138 MDIN1 I MDP input

139 VCCA1 — Power supply (+3.3V)

140 CLVS O Control signal output for selection the spindle control filter constant at CLVS

141 VSS — Ground

142 MDSOUT O Frequency error output terminal of internal CLV circuit


144 MDPOUT O Phase error output of internal CLV circuit

145 DEFECT I Defect signal input (Not used)

146 GSCOR I Guard subcode sync (S0+S1) detection signal input from CXD3068Q

147 EXCK O Subcode serial data reading clock signal output to CXD3068Q

148 SBIN I Subcode serial data input from CXD3068Q

149 VSS — Ground

150 SCOR I Subcode sync (S0+S1) detection signal input from CXD3068Q

151 WFCK I Write frame clock signal input from CXD3068Q


153 XRCI I Not used (Pull down)


155 C2PO I C2 pointer signal input from CXD3068Q


157 DBCK O Bit clock signal (2.8224 MHz) output (Not used)

158 BCLK I Bit clock signal (2.8224 MHz) input from CXD3068Q

159 DDAT O PCM data (Not used)

160 MDAT I Serial data input from CXD3068Q

161 VSS — Ground

162 DLRC O L/R sampling clock signal (Not used)

163 LRCK I L/R sampling clock signal (44.1 kHz) input from CXD3068Q

164 XRST I Reset signal input from CXP973064-245R “L”: reset

165 IFS0 I Not used (connected to ground)

166 IFS1 I Not used (connected to VDD)

167 XTAL I 33.8688 MHz clock signal input from SM8707GV

168 VSS — Ground

169 XTA2 O System clock output (33.8688 MHz)

170 XTA1 I System clock input (33.8688 MHz)


172 to 176 D0 to D4 I/O Two-way data bus with the CXP973064-245R

74

HCD-NXM4D


• IC901 CXP973064-245R (MECHANISM CONTROLLER) (DBM07 Board)

1 NO_USE O Not used (open)

2 SDEN O Serial data enable signal output to SP3723CAFOPM

3DOCTRL/

O Digital out on/off control signal output to CXD3068QISBTEST

4 XRST_2753 O Not used

5 SDA_EEP I/O Data bus with the EEPROM

6 MNT1 I EEPROM ready signal input from TMC57929PGF-RDP

7 FCS_JMP_1 O Focus jump 1 signal output to the FAN8035L

8 FCS_JMP_2 O Focus jump 2 signal output to the FAN8035L

9 SENS_CD I Internal status (SENSE) signal input from CXD3068Q

10 CDSP2 O Not used

11 CDSP4 O Not used

12 XCS_DVD O Chip select signal output to TMC57929PGF-RDP

13 VSS — Ground

14 to 21 D0 to D7 I/O Two-way data bus with TMC57929PGF-RDP

22 INIT0_DVD I Interrupt signal input from TMC57929PGF-RDP

23 INIT1_DVD I Interrupt signal input from TMC57929PGF-RDP

24 MSCK_SAMBA O Not used

25 XRST_1882 O Reset signal output to TMC57929PGF-RDP

26 SCOR I Subcode sync (S0+S1) detection signal input from CXD3068Q

27 LAT_CD O Serial data latch pulse signal output to CXD3068Q

28 LD ON O Laser diode on/off control signal output to SP3723CAFOPM

29 MIRR I Mirror signal input from SP3723CAFOPM

30 COUT_CD I Numbers of track counted signal input from SP3723CAFOPM

31 INLIM I Detection signal input from limit in switch The optical pick-up is inner position when “H”

32 CS_ZIVA O Chip select signal output to ZIVA5X-C1F

33 SI_ZIVA I Serial data input from ZIVA5X-C1F

34 SO_ZIVA O Serial data output to ZIVA5X-C1F

35 SCK_ZIVA O Serial data transfer clock signal output to ZIVA5X-C1F

36 DRVIRQ O Interrupt request signal output to ZIVA5X-C1F

37 DRVRDY O Ready signal output to ZIVA5X-C1F

38 RST I System reset signal input from ZIVA5X-C1F

39 VSS — Ground

40 XTAL I System clock input terminal (20 MHz)

41 EXTAL O System clock output terminal (20 MHz)


43, 44 SLED_A, SLED_B O Sled motor drive signal output to FAN8035L

45 SCK_DSD O Clock output to TMC57929PGF-RDP

46 SDOUT_DSD O Serial data output (Not used)

47 SDIN_DSD I Serial data input (Not used)

48 READY_DSD I Ready signal input (Not used)

49 DATA_CD O Serial data output to CXD3068Q

50 CLOK_CD O Serial data transfer clock signal output to CXD3068Q

51 XMSLAT O Serial data latch pulse signal (Not used)

52 SQSO I Subcode Q data input from TMC57929PGF-RDP

53 MUTE_DSD O Muting on/off control signal (Not used)

54 SQCK O Subcode Q data reading clock signal output to TMC57929PGF-RDP

55 VSS — Ground

56 CONTROL_2 I Not used

75

HCD-NXM4D


57 CONTROL_1 I Not used (open)

58 GFS_DVD I Guard frame sync signal input from TMC57929PGF-RDP

59 MUTE_CD O Muting on/off control signal output to CXD3068Q

60 MUTE_2D O Muting on/off control signal output to FAN8035L

61 SLED I Sled motor servo drive PWM signal input from CXD3068Q

62 FG I Spindle motor control signal input from SP3723CAFOPM

63 SP_ON O Muting on/off control signal output to FAN 8035L

64 JIT I Jitter signal input

65 TE I Tracking error signal input from SP3723CAFOPM

66 PI I Pull in signal input from SP3723CAFOPM

67 FE I Focus error signal input from SP3723CAFOPM

68 AVSS — Ground

69 AVREF I Reference voltage input (for A/D converter)

70 AVDD — Power supply (+3.3V) (for A/D converter)

71 GFS_CD I Guard frame sync signal input from CXD3068Q

72 SCLK_CD O SENSE serial data reading clock signal output to CXD3068Q

73 TSD-M O Thermal shut down signal output to FAN8035L

74 FOK_CD I Focus OK signal input from CXD3068Q

75 LOCK_CD I GFS is sampled by 460 Hz “H” input when GFS is “H”

76 LDSEL O Laser diode selection signal output

77 SACD/DVD O SACD/DVD selection signal output

78 I2C_SIO I/O Communication data bus input/output

79 I2C-SCL I/O Communication data reading clock signal input/output

80 RXD I Serial data input from the RS-232C (for check)

81 TXD O Serial data output to the RS-232C (for check)

82 SDCLK_RF O Serial data transfer clock signal output to SP3723CAFOPM

83 SDATA_RF I/O Two-way data bus with SP3723CAFOPM

84 XWR O Write strobe signal output to TMC57929PGF-RDP

85 XRD O Read strobe signal output to TMC57929PGF-RDP

86 (PWE) — Not used


88 VSS — Ground

89 to 96 A0 to A7 O Address signal output to TMC57929PGF-RDP

97 A8 O Motor/coil driver power save control signal (Not used)

98 XDRST O Reset signal output

99 WP_EEP O Write protect signal output to the EEPROM

100 CLK_EEP O Clock signal output to the EEPROM

76

HCD-NXM4D

• IC401 M3062CMEN-A01FPUO (SYSTEM CONTROL) (MAIN Board)


1 M61530 CLK O Serial clock output to M61530RP

2 M61530 DATA O Serial data output to M61530RP

3 MIC IN I MIC detect signal input

4 SIRCS I Remote commander signal input

5 NO USE – Not used

6 REAR RELAY O Surround relay drive signal output

7 SW RELAY O Super woofer relay drive signal output

8 BYTE I External data bus width select input (connected to ground)

9 CN VSS I Processor modes switch

10 XC-IN I Sub clock input (32.768kHz)

11 XC-OUT O Sub clock output (32.768kHz)

12 RESET I System reset input

13 X-OUT O Main system clock output (16MHz)

14 VSS – Ground

15 X-IN I Main system clock input (16MHz)

16 VCC – Power supply

17 NMI I Non-maskable interrupt input

18 RDS-INT I RDS signal input Clock signal output to the EEPROM

19 SW MUTE O Super woofer mute signal output

20 AC-CUT I AC cut-off detection signal input

21 NO USE – Not used

22 MODEL I Setting terminal for the model

23 DVD VIDEO MUTE O Video out mute signal output

24 DVD VIDEO SW O Video out mute signal output

25 DVD SYS RESET O System reset signal output

26 DVD MUTE REQ O Audio muting request signal output

27 DVD A-MUTE O Audio muting on/off control signal output

28 DVD POWER O DVD power ON/OFF signal output

29 IIC-CLK I/O Communication data reading clock signal input or transfer clock signal output

30 IIC-DATA I/O Communication data bus with CD mechanism and Fluorescent indicater

31 MP3 REQ I REQ signal input from MP3 circuit (not used)

32 REC OUT-MUTE O REC OUT mute signal output

33 CDM-MOT-POS-1 O Motor drive signal output (L/D)

34 CDM-MOT-POS-2 O Motor drive signal output (U/D)

35 CDM-MAIN-SW-CLS I Detection signal input from disc tray close detect main switch

36 CDM-SUB-SW-OPN I Detection signal input from disc tray open detect sub switch

37 CDM-ENC-A-1 I Detection signal input from the disc tray address detect rotary encoder


39 CDM-ENC-B-1 I Detection signal input from the disc tray address detect rotary encoder






45 CDM-SUB-SW-CLS I Detection signal input from disc tray close detect sub switch

46 CDM-MAIN-SW-OPN I Detection signal input from disc tray open detect main switch

47 CDM-MOT-NEG-2 O Motor drive signal output (U/D)

48 CDM-MOT-NEG-1 O Motor drive signal output (L/D)

49 RDS-DATA I RDS data input (connected to ground)

50 ST-MUTE O Tuner muting control signal output to tuner unit

77

HCD-NXM4D


51 TUNED IN I Tuning detecton signal input from tuner unit

52 ST-CE O PLL chip enable signal output to tuner unit

53 ST-DOUT O PLL serial data output to tuner unit

54 ST-DIN I PLL serial data input from tuner unit

55 ST-CLK O PLL serial transfer clock signal output to tuner unit

56 TA-MUTE O Tuner line mute signal output (H:mute on)

57 STK-MUTE O Power amplifier muting on/off selection signal output

58 FRONT-RELAY O Relay drive signal output for speaker protect

59 BIAS O Recording bias on/off selection signal output

60 REC/PB O Recording/playback selection signal output

61 TC-LINE-MUTE O Line mute on/off selection signal output

62 VCC – Power supply

63 TC-REC-MUTE O Recording muting on/off selection signal output

64 VSS – Ground

65 STBY-RELAY O Main power on/off control signal output

66 IO-EXP:CLK O Serial data transfer output to PT8300R

67 IO-EXP:LAT O Serial data latch pulse output to PT8300R

68 IO-EXP DATA IN I Serial data input from PT8300R

69 IO-EXP DATA OUT O Serial data output to PT8300R

70 VOL-A I Jog dial pulse input from the rotary encoder (Volume)

71 VOL-B I Jog dial pulse input from the rotary encoder (Volume)

72 LED-STANDBY O Standby signal output to the LED driver

73 DISPLAY KEY I Display key input signal

74 POWER KEY I Power key input sigal

75 DISC-SENS I Disc status detection signal input

76 JOG 1-A I Jog dial pulse input from the rotary encoder (Bass)

77 JOG 1-B I Jog dial pulse input from the rotary encoder (Bass)

78 JOG 2-A I Jog dial pulse input from the rotary encoder (Treble)

79 JOG 2-B I Jog dial pulse input from the rotary encoder (Treble)

80 AMP-DATA O Serial data output to M61537FP

81 AMP-CLK O Serial clock output to M61537FP

82 FL-RESET O Reset signal output to M66005-0131AHPROT

83 FL-CS O Chip select signal output to M66005-0131AHPROT

84 FL-CLK O Serial clock output to M66005-0131AHPROT

85 FL-DATA O Serial data output to M66005-0131AHPROT

86 CAMP-CNT1 O Capstan motor drive signal output

87 A TRG O Deck-A side trigger plunger drive signal output

88 B TRG O Deck-B side trigger plunger drive signal output

89 A SHUT I Shut off detection signal input from the deck-A side reel pulse detector

90 B SHUT I Shut off detection signal input from the deck-B side reel pulse detector

91 B HALF I Detection input from the deck-B half detect switch

92 SPEC-IN I Setting terminal for the version

93 MAIN-TRANS-CUT I Main transformer cut detect signal input

94 AD-KEY 2 I AD key 2 signal input

95 AD-KEY 1 I AD key 1 signal input

96 AVSS – Ground

97 VACS IN I VACS signal input

98 VREF I Reference voltage input

99 AVCC – Analog power supply

100 AMS-IN I Automatic music sensor signal input

78

HCD-NXM4D

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

SECTION 8EXPLODED VIEWS

8-1. CASE, REAR PANEL SECTION

NOTE:• -XX, -X mean standardized parts, so they may

have some differences from the original one.• Items marked “*” are not stocked since they

are seldom required for routine service. Somedelay should be anticipated when ordering theseitems.

• The mechanical parts with no reference numberin the exploded views are not supplied.


The components identified by mark 0 ordotted line with mark 0 are critical forsafety.Replace only with part number specified.

1

2

3 4

5

6

7

7

7

7

2

2

2

9

10

11

11

12

#1

#1#1

#1

#1

#1

#1#1

#1

#1

#1

not supplied

M961

not supplied

#2

1 A-1063-570-A MAIN BOARD, COMPLETE (TH)1 A-1063-678-A MAIN BOARD, COMPLETE (E3)1 A-1063-681-A MAIN BOARD, COMPLETE (E15)1 A-4752-308-A MAIN BOARD, COMPLETE (SP, MY)1 A-4752-374-A MAIN BOARD, COMPLETE (EA)

1 A-4752-526-A MAIN BOARD, COMPLETE (AUS)1 A-4752-532-A MAIN BOARD, COMPLETE (E2)2 3-970-608-01 SUMITITE (B3), +BV3 1-769-984-11 WIRE (FLAT TYPE) (13 CORE) (EXCEPT TH)4 1-765-333-11 WIRE (FLAT TYPE) (15 CORE) (EXCEPT TH)

5 1-769-872-11 WIRE (FLAT TYPE) (5 CORE) (EXCEPT TH)6 1-769-939-11 WIRE (FLAT TYPE) (11 CORE) (EXCEPT TH)7 3-363-099-22 SCREW (CASE 3 TP2)9 4-252-541-31 CASE10 4-252-538-11 PANEL, TOP

11 4-232-226-01 SCREW, HEXAGON SOCKET TAPPING12 1-693-603-31 TUNER (FM/AM)M961 1-787-099-11 FAN, DC#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3

Ver. 1.2

79

HCD-NXM4D

8-2. FRONT PANEL SECTION


not suppliednot supplied

51

52

53

54

54

56

57 57

57

not supplied

57

57

57

57

57

57

not supplied

57

58

57

59

60

61

57

57

55

55

not supplied

#1

#2

#2

not supplied6362

64

51 4-252-535-11 KNOB (VOL)52 4-252-536-01 KNOB (B/T)53 X-4956-321-1 PANEL ASSY, FRONT54 4-215-062-01 DAMPER55 4-240-965-01 SCREW 2.6X3 +P, S-TITE

56 A-1063-580-A VOL BOARD, COMPLETE (TH)56 A-4752-315-A VOL BOARD, COMPLETE (EXCEPT TH)57 4-951-620-01 SCREW (2.6X8), +BVTP58 A-1063-578-A FL BOARD, COMPLETE (TH)

58 A-4752-675-A FL BOARD, COMPLETE (EXCEPT TH)

59 1-796-880-11 DECK, MECHANISM (W)60 X-4956-197-1 HOLDER (A) (TC) ASSY61 X-4956-198-1 HOLDER (B) (TC) ASSY62 4-252-529-01 SPRING (HA)63 4-252-530-01 SPRING (HB)

64 4-238-628-21 MIC KNOB#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3#2 7-685-853-04 SCREW +BVTT 2X6 (S)

Ver. 1.2

80

HCD-NXM4D

8-3. CHASSIS SECTION


not supplied

not supplied

not supplied

not supplied

not supplied

101108

102

110

103

104

108

108

109

105

108

106111

CDM81A-DVBU60

not supplied

#1

#1#1

#1

#1 #1#1

#1

#9

#1

M962

#1

#1

#1

#1

#1

#1

#1

#1 107

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

101 A-1063-581-A FRONT AMP BOARD, COMPLETE (TH)101 A-4752-316-A FRONT AMP BOARD, COMPLETE

(E3, E15, SP, MY)101 A-4752-377-A FRONT AMP BOARD, COMPLETE (EA)101 A-4752-529-A FRONT AMP BOARD, COMPLETE (AUS)101 A-4752-535-A FRONT AMP BOARD, COMPLETE (E2)

0102 1-468-817-11 REGULATOR, SWITCHING0103 1-775-786-21 CORD, POWER (EA)0103 1-775-790-22 CORD, POWER (AUS)0103 1-777-071-53 CORD, POWER (SP, MY)0103 1-824-818-11 CORD, POWER (WITH CONNECTOR) (TH)

0103 1-827-226-11 CORD, POWER (E2, E3, E15)* 104 3-703-244-00 BUSHING (2104), CORD (EA, TH, AUS, SP, MY)

104 3-703-571-11 BUSHING (S) (4516), CORD (E2, E3, E15)

105 A-1063-595-A DMB07 BOARD, COMPLETE (TH)105 A-4752-324-A DMB07 BOARD, COMPLETE (EXCEPT TH)

106 A-1063-575-A VIDEO BOARD, COMPLETE (TH)106 A-4752-312-A VIDEO BOARD, COMPLETE (EXCEPT TH)107 A-1063-586-A SUR AMP BOARD, COMPLETE (TH)107 A-4752-320-A SUR AMP BOARD, COMPLETE (EXCEPT TH)108 3-970-608-01 SUMITITE (B3), +BV

109 1-500-497-11 FILTER, CLAMP (FERRITE CORE)110 1-543-830-11 CLAMP, SLEEVE FERRITE111 1-500-657-11 CORE, FERRITEM962 1-787-021-11 FAN, DC#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3

#9 7-685-647-79 SCREW +BVTP 3X10 TYPE2

81

HCD-NXM4D

8-4. DVD MECHANISM DECK SECTION-1(CDM81A-DVBU60)


151

152

155

153154

156

157

158

159

160

161

162

163

164

165

166

167

#3

#3

#5

#5

#5

#3

#3

151 4-251-849-01 LEVER (SW2)152 4-251-991-01 SPRING (SW2), TORSION153 4-251-860-01 LEVER (LOCK)154 4-251-867-01 SPRING (LOCK), TORSION155 4-251-828-01 TRAY (MAIN)

156 4-252-533-11 PANEL, LOADING157 4-251-857-01 COVER (R)158 4-251-830-01 SLIDER (ST)159 4-251-858-01 COVER (L)160 4-251-829-02 TRAY (SUB)

161 X-4954-450-1 PULLEY (240) ASSY162 3-053-844-01 YOKE163 4-251-821-02 BRACKET (TOP)164 4-233-594-01 PULLEY (B) (DVD), CHUCKING165 4-251-824-01 LIFTER

166 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING167 4-251-822-01 JOINT (LIFTER)#3 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S#5 7-685-102-19 SCREW +P 2X4 NON-SLIT TYPE 2

82

HCD-NXM4D



not supplied

not supplied

not supplied

not supplied

201202

203203 204

209 214

215

203

214

210

206

207

208

208

208

212213 211

205

#3#3

#3

#4

#4#4

#4

#4

#4

#4

M761

M762

#3

#3

#4

#4

#4

#4#4

#4

S771

201 4-251-870-01 BELT (BU)202 4-251-869-01 BELT (MAIN TRAY)203 4-251-841-01 GEAR (SUB TRAY 1)204 4-251-873-01 SPRING (MODE), COMPRESSION205 4-239-618-02 SCREW (+PWH, 2X6), STEP TAPPING

206 4-251-872-01 SPRING (LEVER), TORSION207 4-251-868-01 BELT (SUB TRAY)208 4-251-853-01 PULLEY (BU)209 4-251-834-01 LEVER (MAIN TRAY)210 4-251-852-01 GEAR (MAIN TRAY 3)

211 4-251-854-01 GEAR (BU1)212 4-251-850-01 GEAR (MAIN TRAY 1)213 4-251-856-01 GEAR (BU2)214 4-251-842-01 GEAR (SUB TRAY 2)215 4-251-851-01 GEAR (MAIN TRAY 2)

M761 A-4713-174-A MOTOR (81) ASSY (LD/ST MOTOR)M762 A-4713-174-A MOTOR (81) ASSY (BU U/D MOTOR)S771 1-478-552-11 ENCODER, ROTARY#3 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S#4 7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)

83

HCD-NXM4D


not supplied

not supplied

not supplied

251

269

268

251258

257

270273 252

272

256

251

261

253262

262

263263

259264

265

262

263

S781

266

267

255271

260254272

252

#3#4

#4#4

#4#3

#3

#3

#3

#4 #4 #4

#4 #4

#4

not supplied

DVBU60

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks251 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING252 4-251-873-01 SPRING (MODE), COMPRESSION253 4-251-874-02 SPRING (SW), TENSION254 4-251-844-01 GEAR (SS2)255 4-251-835-01 GEAR (STOCKER 1)

256 4-251-833-01 LEVER (SUB TRAY)257 4-251-843-01 LEVER (RELEASE)258 4-251-831-02 LEVER (MODE)259 4-251-862-01 SHUTTER (TRAY)260 4-251-845-01 GEAR (SS3)

261 4-251-829-02 TRAY (SUB)262 4-251-827-01 CAM (STOCKER)263 4-251-836-01 GEAR (STOCKER 2)264 4-251-838-01 GEAR (STOCKER 3)

265 4-251-823-01 CHASSIS (CDM81)

266 A-4750-232-A RELAY BOARD, COMPLETE267 4-239-618-02 SCREW (+PWH, 2X6), STEP TAPPING268 4-251-825-01 CAM (BU)269 4-251-832-01 LEVER (STOCKER)270 4-251-861-01 LEVER (SW)

271 4-251-839-01 GEAR (STOCKER 4)272 4-251-840-01 GEAR (SUB TRAY)273 4-251-847-01 GEAR (SS4)S781 1-478-551-11 ENCODER, ROTARY#3 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S

#4 7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)

84

HCD-NXM4D

8-7. BASE UNIT (DVBU60)


301 302

303

303

303

304

304

304

305

306

#3

#3

#8#8


301 X-4956-103-1 HOLDER (DBU1) ASSY0302 A-1067-676-A OPTICAL PICK-UP SERVICE ASSY, DBU-3

303 3-057-023-11 INSULATOR (RB)304 4-981-923-01 SCREW (M), STEP305 1-824-106-12 CABLE, FLEXIBLE FLAT (24 CORE)

306 A-4728-690-A RF BOARD, COMPLETE#3 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S#8 7-685-533-19 SCREW +BTP 2.6X6 TYPE2 N-S

85

HCD-NXM4DSECTION 9

ELECTRICAL PARTS LIST


NOTE:• Due to standardization, replacements in the

parts list may be different from the partsspecified in the diagrams or the componentsused on the set.

• -XX, -X mean standardized parts, so theymay have some difference from the originalone.

• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated whenordering these items.

• CAPACITORS:uF: µF

• RESISTORSAll resistors are in ohms.METAL: metal-film resistorMETAL OXIDE: Metal Oxide-film resistorF: nonflammable

• COILSuH: µH

• SEMICONDUCTORSIn each case, u: µ, for example:uA...: µA... , uPA... , µPA... ,uPB... , µPB... , uPC... , µPC... ,uPD..., µPD...


The components identified by mark 0or dotted line with mark 0 are criticalfor safety.Replace only with part number specified.

When indicating parts by referencenumber, please include the board.

DISC SW BOARD************

< CAPACITOR >

C1001 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16VC1002 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16VC1003 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16VC1004 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16VC1005 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V

C1009 1-164-156-11 CERAMIC CHIP 0.1uF 25V

< DIODE >

D1001 6-500-327-01 DIODE SEL5E23C-STP15 (DISC 1)D1002 6-500-327-01 DIODE SEL5E23C-STP15 (DISC 2)D1003 6-500-327-01 DIODE SEL5E23C-STP15 (DISC 3)D1004 6-500-327-01 DIODE SEL5E23C-STP15 (DISC 4)D1005 6-500-327-01 DIODE SEL5E23C-STP15 (DISC 5)

< TRANSISTOR >

Q1001 8-729-027-43 TRANSISTOR DTC114EKA-T146Q1002 8-729-027-43 TRANSISTOR DTC114EKA-T146Q1003 8-729-027-43 TRANSISTOR DTC114EKA-T146Q1004 8-729-027-43 TRANSISTOR DTC114EKA-T146Q1005 8-729-027-43 TRANSISTOR DTC114EKA-T146

< RESISTOR >

R1001 1-216-821-11 METAL CHIP 1K 5% 1/10WR1002 1-216-821-11 METAL CHIP 1K 5% 1/10WR1003 1-216-821-11 METAL CHIP 1K 5% 1/10WR1004 1-216-821-11 METAL CHIP 1K 5% 1/10WR1005 1-216-821-11 METAL CHIP 1K 5% 1/10W


R1011 1-216-813-11 METAL CHIP 220 5% 1/10WR1012 1-216-815-11 METAL CHIP 330 5% 1/10WR1013 1-216-817-11 METAL CHIP 470 5% 1/10WR1014 1-216-819-11 METAL CHIP 680 5% 1/10W

< SWITCH >

S1001 1-762-875-21 SWITCH, KEYBOARD (DISC 1)S1002 1-762-875-21 SWITCH, KEYBOARD (DISC 2)S1003 1-762-875-21 SWITCH, KEYBOARD (DISC 3)S1004 1-762-875-21 SWITCH, KEYBOARD (DISC 4)S1005 1-762-875-21 SWITCH, KEYBOARD (DISC 5)

******************************************************

A-1063-595-A DMB07 BOARD, COMPLETE (TH)A-4752-324-A DMB07 BOARD, COMPLETE (EXCEPT TH)

********************

< CAPACITOR >

C101 1-126-246-11 ELECT CHIP 220uF 20% 4VC151 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC201 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC202 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC203 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C204 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC205 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC213 1-126-209-11 ELECT CHIP 100uF 20% 4VC214 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC215 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C216 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC218 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC220 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC226 1-107-820-11 CERAMIC CHIP 0.1uF 16VC227 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V



C239 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC240 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC241 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC242 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

DMB07DISC SW

86

HCD-NXM4D


C243 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V



C254 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC255 1-117-370-11 CERAMIC CHIP 10uF 10VC256 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC257 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC258 1-117-370-11 CERAMIC CHIP 10uF 10V


C264 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC265 1-117-370-11 CERAMIC CHIP 10uF 10VC266 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC267 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC268 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V


C275 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC276 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC277 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC278 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC279 1-164-874-11 CERAMIC CHIP 100PF 5% 50V

C280 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC281 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC282 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC283 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC284 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C286 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC287 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC289 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC290 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC291 1-164-874-11 CERAMIC CHIP 100PF 5% 50V


C307 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC308 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC309 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC321 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC322 1-107-820-11 CERAMIC CHIP 0.1uF 16V

C323 1-107-820-11 CERAMIC CHIP 0.1uF 16VC324 1-107-820-11 CERAMIC CHIP 0.1uF 16VC325 1-126-209-11 ELECT CHIP 100uF 20% 4VC326 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC352 1-126-206-11 ELECT CHIP 100uF 20% 6.3V

C355 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC356 1-126-193-11 ELECT CHIP 1uF 20% 50VC357 1-126-193-11 ELECT CHIP 1uF 20% 50VC363 1-107-820-11 CERAMIC CHIP 0.1uF 16VC364 1-126-206-11 ELECT CHIP 100uF 20% 6.3V

C365 1-107-820-11 CERAMIC CHIP 0.1uF 16VC366 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC367 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC368 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC392 1-126-395-11 ELECT CHIP 22uF 20% 16V

C393 1-164-947-11 CERAMIC CHIP 0.01uF 50VC394 1-126-246-11 ELECT CHIP 220uF 20% 4VC501 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC502 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC503 1-127-772-81 CERAMIC CHIP 33000PF 10% 10V

C504 1-127-772-81 CERAMIC CHIP 33000PF 10% 10VC506 1-164-934-11 CERAMIC CHIP 330PF 10% 50VC507 1-117-370-11 CERAMIC CHIP 10uF 10VC508 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC509 1-164-934-11 CERAMIC CHIP 330PF 10% 50V

C510 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC511 1-164-933-11 CERAMIC CHIP 220PF 10% 50VC512 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC513 1-117-370-11 CERAMIC CHIP 10uF 10VC514 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C515 1-164-933-11 CERAMIC CHIP 220PF 10% 50VC516 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC517 1-117-370-11 CERAMIC CHIP 10uF 10VC518 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC519 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C521 1-107-820-11 CERAMIC CHIP 0.1uF 16VC522 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC523 1-107-820-11 CERAMIC CHIP 0.1uF 16VC524 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC525 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C526 1-126-395-11 ELECT CHIP 22uF 20% 16VC527 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC528 1-126-395-11 ELECT CHIP 22uF 20% 16VC529 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC530 1-117-370-11 CERAMIC CHIP 10uF 10V

C531 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10VC532 1-117-370-11 CERAMIC CHIP 10uF 10VC533 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC534 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC535 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V

C540 1-117-370-11 CERAMIC CHIP 10uF 10VC543 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC544 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC545 1-117-370-11 CERAMIC CHIP 10uF 10VC547 1-107-725-11 CERAMIC CHIP 0.1uF 10% 16V

C548 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC551 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V

DMB07

87

HCD-NXM4D


C552 1-216-295-91 SHORT CHIP 0C553 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16VC556 1-117-370-11 CERAMIC CHIP 10uF 10V

C558 1-126-209-11 ELECT CHIP 100uF 20% 4VC559 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC560 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50VC561 1-107-820-11 CERAMIC CHIP 0.1uF 16VC563 1-164-874-11 CERAMIC CHIP 100PF 5% 50V

C565 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC567 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC568 1-117-370-11 CERAMIC CHIP 10uF 10VC569 1-107-820-11 CERAMIC CHIP 0.1uF 16VC570 1-117-370-11 CERAMIC CHIP 10uF 10V

C573 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC588 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC589 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC590 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC592 1-124-779-00 ELECT CHIP 10uF 20% 16V

C701 1-165-643-21 ELECT CHIP 150uF 20% 4VC702 1-117-370-11 CERAMIC CHIP 10uF 10VC703 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC705 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC706 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C708 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC709 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC711 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10VC712 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC713 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V


C720 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC721 1-107-820-11 CERAMIC CHIP 0.1uF 16VC722 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC723 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC724 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C725 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC726 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC727 1-117-370-11 CERAMIC CHIP 10uF 10VC728 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC729 1-117-370-11 CERAMIC CHIP 10uF 10V

C730 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC733 1-117-370-11 CERAMIC CHIP 10uF 10VC734 1-117-370-11 CERAMIC CHIP 10uF 10VC740 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC741 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V




C765 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC766 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC767 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC768 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC769 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V


C775 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC776 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC777 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC778 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC779 1-117-370-11 CERAMIC CHIP 10uF 10V

C780 1-117-370-11 CERAMIC CHIP 10uF 10VC781 1-165-643-21 ELECT CHIP 150uF 20% 4VC782 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50VC783 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50VC901 1-126-209-11 ELECT CHIP 100uF 20% 4V

C902 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC903 1-126-209-11 ELECT CHIP 100uF 20% 4VC904 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC905 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC906 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C907 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC908 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC909 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC910 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC913 1-127-772-81 CERAMIC CHIP 33000PF 10% 10V

C914 1-164-849-11 CERAMIC CHIP 9PF 0.5PF 50VC915 1-164-847-11 CERAMIC CHIP 7PF 0.5PF 50VC916 1-126-209-11 ELECT CHIP 100uF 20% 4VC917 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC918 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C924 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC925 1-126-395-11 ELECT CHIP 22uF 20% 16VC926 1-126-246-11 ELECT CHIP 220uF 20% 4VC927 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC928 1-117-370-11 CERAMIC CHIP 10uF 10V


< CONNECTOR >

CN101 1-784-366-21 CONNECTOR, FFC/FPC 7PCN102 1-815-954-21 PIN, CONNECTOR (PC BOARD) 13PCN105 1-784-376-11 CONNECTOR, FFC/FPC 17PCN107 1-778-692-11 CONNECTOR, FFC/FPC 21PCN202 1-784-364-21 CONNECTOR, FFC/FPC 4P

CN501 1-778-957-11 CONNECTOR, FFC/FPC 29PCN901 1-764-177-11 PIN, CONNECTOR (SMD) (1.5MM) 7P

< DIODE >

D202 8-719-988-61 DIODE 1SS355TE-17D392 8-719-988-61 DIODE 1SS355TE-17D393 8-719-988-61 DIODE 1SS355TE-17

DMB07

88

HCD-NXM4D

Ref. No. Part No. Description Remarks Ref. No. Part No. Description RemarksRef. No. Part No. Description Remarks

D394 8-719-988-61 DIODE 1SS355TE-17D500 8-719-988-61 DIODE 1SS355TE-17

D901 8-719-988-61 DIODE 1SS355TE-17D1303 8-719-988-61 DIODE 1SS355TE-17D1304 8-719-988-61 DIODE 1SS355TE-17

< FERRITE BEAD >

FB105 1-469-324-21 FERRITE, EMIFB902 1-500-284-21 INDUCTOR, FERRITE BEADFB903 1-500-284-21 INDUCTOR, FERRITE BEAD

< FILTER >

FL101 1-234-177-21 FILTER, CHIP EMIFL203 1-234-177-21 FILTER, CHIP EMIFL204 1-234-177-21 FILTER, CHIP EMIFL205 1-234-177-21 FILTER, CHIP EMIFL206 1-234-177-21 FILTER, CHIP EMI



FL901 1-234-177-21 FILTER, CHIP EMIFL903 1-234-177-21 FILTER, CHIP EMIFL908 1-234-177-21 FILTER, CHIP EMI

< IC >

IC111 6-550-554-01 TRANSISTOR UM6K1NL02TNIC203 6-704-069-01 IC MT48LC4M32B2P-6-Y15W

* IC204 6-703-671-01 IC BR9040F-WE2IC206 6-804-579-01 IC MBM29PL32BM90TN-NXM0401IC207 6-704-630-01 IC ZIVA5X-C2F

IC211 6-700-398-01 IC uPC2918T-E1IC231 8-759-549-21 IC SN74LV573APWRIC232 8-759-549-21 IC SN74LV573APWRIC233 8-759-549-21 IC SN74LV573APWRIC256 8-759-549-21 IC SN74LV573APWR

IC258 8-759-549-21 IC SN74LV573APWRIC259 8-759-549-21 IC SN74LV573APWRIC302 6-703-787-01 IC PCM1609KPTRIC352 8-759-560-56 IC PCM1800E/2KIC392 8-759-583-47 IC uPC2933T-E2

IC501 6-702-157-01 IC FAN8035LIC502 8-759-583-47 IC uPC2933T-E2IC503 8-759-058-43 IC NJM3404AVIC509 8-752-408-73 IC CXD3068QIC701 6-703-552-01 IC TMC57929PGF-RDP

IC703 8-759-058-43 IC NJM3404AVIC706 8-759-564-30 IC MSM51V18165B-60TSKR1IC901 8-753-228-87 IC CXP973064-245RIC902 8-759-649-48 IC SN74AHC1G32DCKRIC903 6-704-004-01 IC BR24L16F-WE2

IC904 6-704-753-01 IC SN74AHC2G74HDCURIC906 6-700-407-01 IC SM8707GV-G-E2IC907 8-759-583-47 IC uPC2933T-E2

< JUMPER RESISTOR >

JW392 1-216-864-11 SHORT CHIP 0JW801 1-218-990-11 SHORT CHIP 0JW802 1-218-990-11 SHORT CHIP 0JW803 1-218-990-11 SHORT CHIP 0JW804 1-218-990-11 SHORT CHIP 0

JW805 1-218-990-11 SHORT CHIP 0JW806 1-218-990-11 SHORT CHIP 0

< COIL >

L103 1-216-296-11 SHORT CHIP 0L501 1-216-296-11 SHORT CHIP 0L704 1-412-031-11 INDUCTOR 47uHL901 1-412-031-11 INDUCTOR 47uH

< TRANSISTOR >

Q201 8-729-929-26 TRANSISTOR DTC114TEQ202 8-729-929-26 TRANSISTOR DTC114TEQ901 8-729-929-26 TRANSISTOR DTC114TE

< RESISTOR >

R10 1-216-801-11 METAL CHIP 22 5% 1/10WR11 1-216-801-11 METAL CHIP 22 5% 1/10WR12 1-216-801-11 METAL CHIP 22 5% 1/10WR13 1-216-801-11 METAL CHIP 22 5% 1/10WR14 1-216-801-11 METAL CHIP 22 5% 1/10W

R15 1-216-801-11 METAL CHIP 22 5% 1/10WR197 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR198 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR202 1-216-841-11 METAL CHIP 47K 5% 1/10WR213 1-218-939-11 RES-CHIP 68 5% 1/16W

R215 1-216-864-11 SHORT CHIP 0R217 1-216-864-11 SHORT CHIP 0R219 1-216-864-11 SHORT CHIP 0R220 1-216-864-11 SHORT CHIP 0R221 1-216-864-11 SHORT CHIP 0

R222 1-216-864-11 SHORT CHIP 0R225 1-216-864-11 SHORT CHIP 0R226 1-216-864-11 SHORT CHIP 0R227 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR228 1-216-864-11 SHORT CHIP 0

R230 1-216-803-11 METAL CHIP 33 5% 1/10WR231 1-216-803-11 METAL CHIP 33 5% 1/10WR232 1-216-803-11 METAL CHIP 33 5% 1/10WR234 1-216-833-11 METAL CHIP 10K 5% 1/10WR239 1-216-809-11 METAL CHIP 100 5% 1/10W

R240 1-216-841-11 METAL CHIP 47K 5% 1/10WR241 1-216-864-11 SHORT CHIP 0R244 1-216-821-11 METAL CHIP 1K 5% 1/10WR245 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR246 1-216-833-11 METAL CHIP 10K 5% 1/10W

R247 1-216-821-11 METAL CHIP 1K 5% 1/10WR248 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

DMB07

89

HCD-NXM4D


R250 1-216-864-11 SHORT CHIP 0R251 1-216-864-11 SHORT CHIP 0R253 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R254 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR255 1-216-864-11 SHORT CHIP 0R257 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR259 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR260 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R261 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR263 1-218-285-11 METAL CHIP 75 5% 1/10WR264 1-218-285-11 METAL CHIP 75 5% 1/10WR265 1-218-285-11 METAL CHIP 75 5% 1/10WR266 1-218-285-11 METAL CHIP 75 5% 1/10W

R267 1-218-285-11 METAL CHIP 75 5% 1/10WR268 1-216-864-11 SHORT CHIP 0R269 1-216-864-11 SHORT CHIP 0R270 1-216-864-11 SHORT CHIP 0R271 1-216-809-11 METAL CHIP 100 5% 1/10W

R272 1-216-809-11 METAL CHIP 100 5% 1/10WR273 1-216-864-11 SHORT CHIP 0R274 1-216-864-11 SHORT CHIP 0R275 1-216-864-11 SHORT CHIP 0R276 1-216-864-11 SHORT CHIP 0

R277 1-216-864-11 SHORT CHIP 0R278 1-218-285-11 METAL CHIP 75 5% 1/10WR279 1-218-285-11 METAL CHIP 75 5% 1/10WR280 1-218-285-11 METAL CHIP 75 5% 1/10WR281 1-218-285-11 METAL CHIP 75 5% 1/10W

R282 1-218-285-11 METAL CHIP 75 5% 1/10WR283 1-218-847-11 METAL CHIP 1K 0.5% 1/10WR284 1-218-829-11 METAL CHIP 180 0.5% 1/10WR288 1-216-864-11 SHORT CHIP 0R290 1-216-809-11 METAL CHIP 100 5% 1/10W

R291 1-216-809-11 METAL CHIP 100 5% 1/10WR292 1-216-809-11 METAL CHIP 100 5% 1/10WR293 1-216-864-11 SHORT CHIP 0R294 1-216-864-11 SHORT CHIP 0R296 1-216-864-11 SHORT CHIP 0

R299 1-216-820-11 METAL CHIP 820 5% 1/10WR301 1-216-821-11 METAL CHIP 1K 5% 1/10WR302 1-216-813-11 METAL CHIP 220 5% 1/10WR303 1-216-813-11 METAL CHIP 220 5% 1/10WR304 1-216-813-11 METAL CHIP 220 5% 1/10W


R310 1-216-809-11 METAL CHIP 100 5% 1/10WR311 1-216-809-11 METAL CHIP 100 5% 1/10WR312 1-216-809-11 METAL CHIP 100 5% 1/10WR313 1-216-833-11 METAL CHIP 10K 5% 1/10WR314 1-216-801-11 METAL CHIP 22 5% 1/10W


R353 1-216-864-11 SHORT CHIP 0R362 1-216-833-11 METAL CHIP 10K 5% 1/10WR367 1-216-864-11 SHORT CHIP 0R368 1-216-864-11 SHORT CHIP 0R369 1-216-864-11 SHORT CHIP 0

R392 1-216-797-11 METAL CHIP 10 5% 1/10WR503 1-216-841-11 METAL CHIP 47K 5% 1/10WR504 1-216-841-11 METAL CHIP 47K 5% 1/10WR505 1-216-841-11 METAL CHIP 47K 5% 1/10WR506 1-216-841-11 METAL CHIP 47K 5% 1/10W


R515 1-216-833-11 METAL CHIP 10K 5% 1/10WR516 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR517 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR519 1-216-845-11 METAL CHIP 100K 5% 1/10WR520 1-216-833-11 METAL CHIP 10K 5% 1/10W

R521 1-216-845-11 METAL CHIP 100K 5% 1/10WR522 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR523 1-216-833-11 METAL CHIP 10K 5% 1/10WR524 1-216-833-11 METAL CHIP 10K 5% 1/10WR525 1-216-833-11 METAL CHIP 10K 5% 1/10W

R527 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR529 1-216-839-11 METAL CHIP 33K 5% 1/10WR530 1-216-842-11 METAL CHIP 56K 5% 1/10WR533 1-216-839-11 METAL CHIP 33K 5% 1/10WR534 1-216-842-11 METAL CHIP 56K 5% 1/10W


R551 1-216-821-11 METAL CHIP 1K 5% 1/10WR552 1-216-821-11 METAL CHIP 1K 5% 1/10WR555 1-216-864-11 SHORT CHIP 0R558 1-216-841-11 METAL CHIP 47K 5% 1/10WR559 1-216-821-11 METAL CHIP 1K 5% 1/10W


R565 1-216-821-11 METAL CHIP 1K 5% 1/10WR566 1-216-833-11 METAL CHIP 10K 5% 1/10WR567 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR568 1-216-857-11 METAL CHIP 1M 5% 1/10WR571 1-216-857-11 METAL CHIP 1M 5% 1/10W

R572 1-216-853-11 METAL CHIP 470K 5% 1/10WR573 1-216-833-11 METAL CHIP 10K 5% 1/10WR576 1-216-864-11 SHORT CHIP 0R579 1-216-832-11 METAL CHIP 8.2K 5% 1/10WR580 1-216-839-11 METAL CHIP 33K 5% 1/10W

R581 1-216-834-11 METAL CHIP 12K 5% 1/10WR583 1-216-864-11 SHORT CHIP 0R584 1-216-839-11 METAL CHIP 33K 5% 1/10W

DMB07

90

HCD-NXM4D


R586 1-218-747-11 METAL CHIP 200K 0.5% 1/10WR587 1-216-864-11 SHORT CHIP 0

R588 1-216-833-11 METAL CHIP 10K 5% 1/10WR589 1-216-833-11 METAL CHIP 10K 5% 1/10WR591 1-216-864-11 SHORT CHIP 0R593 1-216-845-11 METAL CHIP 100K 5% 1/10WR599 1-216-821-11 METAL CHIP 1K 5% 1/10W

R601 1-216-864-11 SHORT CHIP 0R629 1-216-864-11 SHORT CHIP 0R694 1-216-833-11 METAL CHIP 10K 5% 1/10WR698 1-216-864-11 SHORT CHIP 0R699 1-216-864-11 SHORT CHIP 0

R700 1-216-832-11 METAL CHIP 8.2K 5% 1/10WR707 1-216-809-11 METAL CHIP 100 5% 1/10WR708 1-216-853-11 METAL CHIP 470K 5% 1/10WR709 1-216-847-11 METAL CHIP 150K 5% 1/10WR710 1-216-833-11 METAL CHIP 10K 5% 1/10W



R721 1-216-839-11 METAL CHIP 33K 5% 1/10WR724 1-216-821-11 METAL CHIP 1K 5% 1/10WR725 1-216-824-11 METAL CHIP 1.8K 5% 1/10WR726 1-216-845-11 METAL CHIP 100K 5% 1/10WR727 1-216-827-11 METAL CHIP 3.3K 5% 1/10W

R728 1-216-833-11 METAL CHIP 10K 5% 1/10WR730 1-216-801-11 METAL CHIP 22 5% 1/10WR731 1-216-801-11 METAL CHIP 22 5% 1/10WR732 1-216-833-11 METAL CHIP 10K 5% 1/10WR733 1-216-833-11 METAL CHIP 10K 5% 1/10W


R741 1-216-801-11 METAL CHIP 22 5% 1/10WR742 1-216-801-11 METAL CHIP 22 5% 1/10WR743 1-216-801-11 METAL CHIP 22 5% 1/10WR744 1-216-801-11 METAL CHIP 22 5% 1/10WR745 1-216-841-11 METAL CHIP 47K 5% 1/10W

R746 1-216-841-11 METAL CHIP 47K 5% 1/10WR747 1-216-839-11 METAL CHIP 33K 5% 1/10WR748 1-216-839-11 METAL CHIP 33K 5% 1/10WR750 1-216-833-11 METAL CHIP 10K 5% 1/10WR751 1-216-864-11 SHORT CHIP 0

R758 1-216-864-11 SHORT CHIP 0R760 1-216-864-11 SHORT CHIP 0R762 1-216-837-11 METAL CHIP 22K 5% 1/10WR763 1-216-832-11 METAL CHIP 8.2K 5% 1/10WR764 1-216-857-11 METAL CHIP 1M 5% 1/10W

R765 1-216-837-11 METAL CHIP 22K 5% 1/10WR767 1-216-841-11 METAL CHIP 47K 5% 1/10WR769 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR776 1-216-864-11 SHORT CHIP 0R777 1-216-864-11 SHORT CHIP 0


R789 1-216-845-11 METAL CHIP 100K 5% 1/10WR799 1-216-864-11 SHORT CHIP 0R805 1-216-864-11 SHORT CHIP 0R901 1-216-801-11 METAL CHIP 22 5% 1/10WR902 1-216-801-11 METAL CHIP 22 5% 1/10W

R904 1-216-833-11 METAL CHIP 10K 5% 1/10WR905 1-216-801-11 METAL CHIP 22 5% 1/10WR906 1-216-801-11 METAL CHIP 22 5% 1/10WR907 1-216-801-11 METAL CHIP 22 5% 1/10WR908 1-216-833-11 METAL CHIP 10K 5% 1/10W

R911 1-216-833-11 METAL CHIP 10K 5% 1/10WR912 1-216-833-11 METAL CHIP 10K 5% 1/10WR913 1-216-833-11 METAL CHIP 10K 5% 1/10WR915 1-216-809-11 METAL CHIP 100 5% 1/10WR916 1-216-821-11 METAL CHIP 1K 5% 1/10W

R917 1-216-821-11 METAL CHIP 1K 5% 1/10WR918 1-216-801-11 METAL CHIP 22 5% 1/10WR920 1-216-809-11 METAL CHIP 100 5% 1/10WR921 1-216-809-11 METAL CHIP 100 5% 1/10WR922 1-216-801-11 METAL CHIP 22 5% 1/10W

R923 1-216-813-11 METAL CHIP 220 5% 1/10WR925 1-216-809-11 METAL CHIP 100 5% 1/10WR926 1-216-809-11 METAL CHIP 100 5% 1/10WR927 1-216-857-11 METAL CHIP 1M 5% 1/10WR928 1-216-809-11 METAL CHIP 100 5% 1/10W


R935 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR936 1-216-809-11 METAL CHIP 100 5% 1/10WR938 1-216-833-11 METAL CHIP 10K 5% 1/10WR940 1-216-809-11 METAL CHIP 100 5% 1/10WR942 1-216-809-11 METAL CHIP 100 5% 1/10W

R943 1-216-809-11 METAL CHIP 100 5% 1/10WR958 1-216-801-11 METAL CHIP 22 5% 1/10WR962 1-216-833-11 METAL CHIP 10K 5% 1/10WR964 1-216-833-11 METAL CHIP 10K 5% 1/10WR970 1-216-864-11 SHORT CHIP 0

R974 1-216-864-11 SHORT CHIP 0R975 1-216-833-11 METAL CHIP 10K 5% 1/10WR978 1-216-833-11 METAL CHIP 10K 5% 1/10WR984 1-216-833-11 METAL CHIP 10K 5% 1/10WR988 1-216-864-11 SHORT CHIP 0

R990 1-216-864-11 SHORT CHIP 0R994 1-216-864-11 SHORT CHIP 0R995 1-216-864-11 SHORT CHIP 0

DMB07

91

HCD-NXM4D


R996 1-216-864-11 SHORT CHIP 0R997 1-216-864-11 SHORT CHIP 0

R998 1-216-864-11 SHORT CHIP 0R1000 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1001 1-216-864-11 SHORT CHIP 0R1302 1-216-864-11 SHORT CHIP 0R9980 1-216-864-11 SHORT CHIP 0


R9998 1-216-864-11 SHORT CHIP 0R9999 1-216-864-11 SHORT CHIP 0

< VIBRATOR >

X901 1-781-945-21 VIBRATOR, CERAMIC (20MHz) (TH)X901 1-795-375-11 VIBRATOR, CERAMIC (20MHz) (EXCEPT TH)X902 1-795-630-11 VIBRATOR, CRYSTAL (27MHz)

******************************************************

A-1063-581-A FRONT AMP BOARD, COMPLETE (TH)A-4752-316-A FRONT AMP BOARD, COMPLETE

(E3, E15, SP, MY)A-4752-377-A FRONT AMP BOARD, COMPLETE (EA)A-4752-529-A FRONT AMP BOARD, COMPLETE (AUS)A-4752-535-A FRONT AMP BOARD, COMPLETE (E2)

***********************

< CAPACITOR >

C501 1-126-964-11 ELECT 10uF 20% 50VC502 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC503 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC504 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC505 1-126-964-11 ELECT 10uF 20% 50V

C506 1-126-947-11 ELECT 47uF 20% 35VC507 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC508 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC509 1-126-947-11 ELECT 47uF 20% 35VC510 1-126-947-11 ELECT 47uF 20% 35V

C511 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC513 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC515 1-126-967-11 ELECT 47uF 20% 50VC516 1-126-967-11 ELECT 47uF 20% 50VC518 1-128-563-11 ELECT 100uF 20% 100V

C522 1-137-749-11 MYLAR 0.1uF 100VC523 1-137-749-11 MYLAR 0.1uF 100VC524 1-137-749-11 MYLAR 0.1uF 100VC525 1-137-749-11 MYLAR 0.1uF 100VC526 1-136-497-81 FILM 0.1uF 5% 50V

C527 1-136-497-81 FILM 0.1uF 5% 50VC528 1-128-562-11 ELECT 47uF 20% 100VC529 1-162-974-11 CERAMIC CHIP 0.01uF 50VC530 1-128-550-11 ELECT 2200uF 20% 50VC531 1-128-550-11 ELECT 2200uF 20% 50V

C534 1-126-953-11 ELECT 2200uF 20% 35VC535 1-126-953-11 ELECT 2200uF 20% 35VC537 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)

C538 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C539 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)

C540 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C541 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C542 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C543 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C544 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)

C545 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C546 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C547 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C548 1-131-992-91 CERAMIC CHIP 100000PF 35V (EA)C557 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C560 1-126-964-11 ELECT 10uF 20% 50VC850 1-126-964-11 ELECT 10uF 20% 50VC851 1-104-658-91 ELECT 100uF 20% 10VC852 1-126-961-11 ELECT 2.2uF 20% 50VC853 1-126-923-91 ELECT 220uF 20% 10V

C854 1-126-964-11 ELECT 10uF 20% 50VC855 1-107-721-11 ELECT 4.7uF 20% 100VC856 1-107-721-11 ELECT 4.7uF 20% 100VC857 1-162-974-11 CERAMIC CHIP 0.01uF 50VC858 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C859 1-126-947-11 ELECT 47uF 20% 35VC860 1-126-963-11 ELECT 4.7uF 20% 50VC861 1-104-658-91 ELECT 100uF 20% 10VC862 1-104-658-91 ELECT 100uF 20% 10VC865 1-126-965-11 ELECT 22uF 20% 50V

< CONNECTOR >

CN501 1-784-031-41 CONNECTOR, BOARD TO BOARD 8P* CN502 1-564-526-11 PLUG, CONNECTOR 11P

CN503 1-691-773-11 PLUG (MICRO CONNECTOR) 11PCN505 1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P

* CN506 1-564-518-11 PLUG, CONNECTOR 3P

CN507 1-564-506-11 PLUG, CONNECTOR 3PCN508 1-766-719-41 CONNECTOR, BOARD TO BOARD 10P

< DIODE >

D501 8-719-988-61 DIODE 1SS355TE-17D502 8-719-083-83 DIODE UDZS-TE17-15BD503 8-719-083-83 DIODE UDZS-TE17-15BD504 8-719-988-61 DIODE 1SS355TE-17D505 8-719-988-61 DIODE 1SS355TE-17

D506 8-719-988-61 DIODE 1SS355TE-17D507 8-719-988-61 DIODE 1SS355TE-17D508 8-719-988-61 DIODE 1SS355TE-17D509 8-719-988-61 DIODE 1SS355TE-17D510 8-719-988-61 DIODE 1SS355TE-17

D850 8-719-069-56 DIODE UDZSTE-176.2BD851 8-719-978-33 DIODE DTZ-TT11-6.8BD852 8-719-988-61 DIODE 1SS355TE-17D853 8-719-988-61 DIODE 1SS355TE-17

< EARTH TERMINAL >

* EP502 1-537-738-21 TERMINAL, EARTH

DMB07 FRONT AMP

92

HCD-NXM4D


< IC >

IC501 6-706-124-01 IC STK413-420IC850 6-703-610-01 IC RT8H015C-T112-1

< COIL >

L501 1-420-872-52 COIL, AIR-CORE (EA)L502 1-420-872-52 COIL, AIR-CORE (EA)L503 1-420-872-52 COIL, AIR-CORE (EA)L504 1-420-872-52 COIL, AIR-CORE (EA)L505 1-420-872-52 COIL, AIR-CORE (EA)

L506 1-420-872-52 COIL, AIR-CORE (EA)

< TRANSISTOR >

Q501 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q502 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q503 8-729-271-31 TRANSISTOR 2SC2713-GQ504 8-729-140-84 TRANSISTOR 2SC1841-PAFAEAQ505 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA

Q506 8-729-140-84 TRANSISTOR 2SC1841-PAFAEAQ507 8-729-216-31 TRANSISTOR 2SA1163-GQ508 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q509 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q510 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Q850 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q851 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q852 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q853 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q854 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16

Q858 8-729-026-68 TRANSISTOR 2SD2525 (TP)Q859 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q860 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q861 8-729-027-43 TRANSISTOR DTC114EKA-T146Q868 8-729-027-23 TRANSISTOR DTA114EKA-T146

Q869 8-729-027-43 TRANSISTOR DTC114EKA-T146Q890 8-729-027-43 TRANSISTOR DTC114EKA-T146

< RESISTOR >


R509 1-216-821-11 METAL CHIP 1K 5% 1/10WR510 1-216-815-11 METAL CHIP 330 5% 1/10WR511 1-216-811-11 METAL CHIP 150 5% 1/10WR512 1-216-811-11 METAL CHIP 150 5% 1/10WR513 1-216-841-11 METAL CHIP 47K 5% 1/10W


0R520 1-245-605-51 FUSIBLE 100 5% 1/4W0R521 1-245-605-51 FUSIBLE 100 5% 1/4W

R522 1-216-835-11 METAL CHIP 15K 5% 1/10WR523 1-216-839-11 METAL CHIP 33K 5% 1/10W

0R524 1-217-637-00 FUSIBLE 1 5% 1/4W

R525 1-249-677-31 CARBON 1.5K 5% 1/2WR526 1-249-677-31 CARBON 1.5K 5% 1/2WR527 1-216-841-11 METAL CHIP 47K 5% 1/10W

0R529 1-220-755-11 METAL 0.22 10% 2WR530 1-216-821-11 METAL CHIP 1K 5% 1/10W


0R536 1-220-755-11 METAL 0.22 10% 2WR538 1-216-835-11 METAL CHIP 15K 5% 1/10WR539 1-216-821-11 METAL CHIP 1K 5% 1/10WR540 1-216-845-11 METAL CHIP 100K 5% 1/10W

0R541 1-220-894-11 METAL 0.22 10% 5W

R542 1-249-625-31 CARBON 10 5% 1/2WR543 1-249-625-31 CARBON 10 5% 1/2WR544 1-249-625-31 CARBON 10 5% 1/2WR545 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR546 1-216-841-11 METAL CHIP 47K 5% 1/10W

R547 1-216-843-11 METAL CHIP 68K 5% 1/10WR548 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR549 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR550 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR554 1-216-837-11 METAL CHIP 22K 5% 1/10W

R555 1-216-837-11 METAL CHIP 22K 5% 1/10WR556 1-216-837-11 METAL CHIP 22K 5% 1/10WR557 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR559 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR560 1-216-833-11 METAL CHIP 10K 5% 1/10W

R561 1-249-625-31 CARBON 10 5% 1/2W(EA)

R562 1-249-625-31 CARBON 10 5% 1/2W(EA)

R563 1-249-625-31 CARBON 10 5% 1/2W(EA)


R566 1-249-625-31 CARBON 10 5% 1/2W(EA)

R567 1-216-843-11 METAL CHIP 68K 5% 1/10WR568 1-216-843-11 METAL CHIP 68K 5% 1/10WR569 1-216-841-11 METAL CHIP 47K 5% 1/10W

0R570 1-216-458-11 METAL OXIDE 1.8K 5% 2W

0R571 1-216-458-11 METAL OXIDE 1.8K 5% 2W0R572 1-216-458-11 METAL OXIDE 1.8K 5% 2W0R573 1-216-458-11 METAL OXIDE 1.8K 5% 2W

R574 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR575 1-216-833-11 METAL CHIP 10K 5% 1/10W

R576 1-249-625-31 CARBON 10 5% 1/2W(EA)

R577 1-216-841-11 METAL CHIP 47K 5% 1/10WR578 1-249-625-31 CARBON 10 5% 1/2W

(EA)0R580 1-215-863-11 METAL OXIDE 100 5% 1W0R581 1-215-863-11 METAL OXIDE 100 5% 1W


FRONT AMP

93

HCD-NXM4D



(EA)R584 1-249-625-31 CARBON 10 5% 1/2W

(EA)R585 1-249-625-31 CARBON 10 5% 1/2W

(EA)R586 1-216-841-11 METAL CHIP 47K 5% 1/10W

R587 1-249-625-31 CARBON 10 5% 1/2W(EA)


(EA)R591 1-249-625-31 CARBON 10 5% 1/2W

(EA)R595 1-249-689-31 CARBON 4.7K 5% 1/2W

R596 1-249-689-31 CARBON 4.7K 5% 1/2WR598 1-249-689-31 CARBON 4.7K 5% 1/2WR599 1-249-689-31 CARBON 4.7K 5% 1/2WR850 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR851 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R854 1-216-821-11 METAL CHIP 1K 5% 1/10WR855 1-215-891-11 METAL OXIDE 680 5% 2WR857 1-216-821-11 METAL CHIP 1K 5% 1/10WR858 1-215-891-11 METAL OXIDE 680 5% 2WR860 1-216-829-11 METAL CHIP 4.7K 5% 1/10W


R867 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR870 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR871 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR872 1-216-845-11 METAL CHIP 100K 5% 1/10WR875 1-216-813-11 METAL CHIP 220 5% 1/10W

R876 1-216-813-11 METAL CHIP 220 5% 1/10WR880 1-216-837-11 METAL CHIP 22K 5% 1/10WR890 1-216-833-11 METAL CHIP 10K 5% 1/10W

< RELAY >

RY501 1-755-373-11 RELAYRY502 1-755-373-11 RELAY

< THERMISTOR >

TH531 1-807-796-11 THERMISTOR

< TERMINAL >

TM502 1-694-656-21 TERMINAL BOARD (6CH SPEAKER) (SPEAKER)******************************************************

HP BOARD********

< CAPACITOR >

C1060 1-124-464-11 ELECT 0.22uF 20% 50VC1061 1-162-974-11 CERAMIC CHIP 0.01uF 50VC1062 1-124-464-11 ELECT 0.22uF 20% 50VC1063 1-162-974-11 CERAMIC CHIP 0.01uF 50V


C1066 1-162-949-11 CERAMIC CHIP 47PF 5% 50VC1067 1-162-957-11 CERAMIC CHIP 220PF 5% 50VC1068 1-124-464-11 ELECT 0.22uF 20% 50VC1069 1-124-257-00 ELECT 2.2uF 20% 50VC1070 1-162-953-11 CERAMIC CHIP 100PF 5% 50V

C1071 1-162-949-11 CERAMIC CHIP 47PF 5% 50VC1072 1-124-247-91 ELECT 10uF 20% 35VC1073 1-124-257-00 ELECT 2.2uF 20% 50VC1074 1-126-176-11 ELECT 220uF 20% 10VC1076 1-124-247-91 ELECT 10uF 20% 35V

C1077 1-126-160-11 ELECT 1uF 20% 50VC1078 1-124-257-00 ELECT 2.2uF 20% 50VC1079 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC1080 1-126-160-11 ELECT 1uF 20% 50VC1082 1-124-589-11 ELECT 47uF 20% 16V

C1083 1-124-589-11 ELECT 47uF 20% 16VC1084 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16VC1085 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC1086 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC1087 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V


C1093 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50VC1094 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50VC1095 1-162-974-11 CERAMIC CHIP 0.01uF 50VC1096 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

< CONNECTOR >

CN1060 1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4PCN1062 1-785-329-11 PIN, CONNECTOR (LIGHT ANGLE) 3P

< DIODE >

D1061 8-719-069-54 DIODE UDZSTE-175.1B

< EARTH TERMINAL >

* EP1060 1-537-738-21 TERMINAL, EARTH* EP1061 1-537-738-21 TERMINAL, EARTH

< FERRITE BEAD >

FB1001 1-414-671-11 INDUCTOR, FERRITE BEADFB1002 1-414-671-11 INDUCTOR, FERRITE BEADFB1010 1-469-125-11 FERRITE EMIFB1011 1-469-125-11 FERRITE EMIFB1003 1-414-671-11 INDUCTOR, FERRITE BEAD

FB1004 1-414-671-11 INDUCTOR, FERRITE BEAD

< IC >

IC1060 8-759-710-97 IC NJM4565M-DIC1061 8-759-496-41 IC M65850FP-E1

< JACK >

J1060 1-770-226-11 JACK (LARGE TYPE) (MIC 1)

HPFRONT AMP

94

HCD-NXM4D


J1061 1-770-226-11 JACK (LARGE TYPE) (MIC 2)J1063 1-750-032-11 JACK (DIA. 3.5) (PHONES)

< SHORT >

JR1080 1-216-864-11 SHORT CHIP 0JR1081 1-216-864-11 SHORT CHIP 0

< RESISTOR >


R1065 1-216-821-11 METAL CHIP 1K 5% 1/10WR1066 1-216-841-11 METAL CHIP 47K 5% 1/10WR1067 1-216-809-11 METAL CHIP 100 5% 1/10WR1068 1-216-833-11 METAL CHIP 10K 5% 1/10WR1069 1-216-847-11 METAL CHIP 150K 5% 1/10W

R1070 1-216-809-11 METAL CHIP 100 5% 1/10WR1071 1-216-833-11 METAL CHIP 10K 5% 1/10WR1072 1-216-833-11 METAL CHIP 10K 5% 1/10WR1073 1-216-845-11 METAL CHIP 100K 5% 1/10WR1074 1-216-864-11 SHORT CHIP 0

R1075 1-216-833-11 METAL CHIP 10K 5% 1/10WR1076 1-216-835-11 METAL CHIP 15K 5% 1/10WR1077 1-216-835-11 METAL CHIP 15K 5% 1/10WR1078 1-216-837-11 METAL CHIP 22K 5% 1/10WR1079 1-216-813-11 METAL CHIP 220 5% 1/10W


R1085 1-216-837-11 METAL CHIP 22K 5% 1/10WR1086 1-216-837-11 METAL CHIP 22K 5% 1/10WR1088 1-216-864-11 SHORT CHIP 0

< VARIABLE RESISTOR >

RV1060 1-223-983-11 RES, VAR, CARBON 50K (MIC LEVEL)RV1061 1-223-983-11 RES, VAR, CARBON 50K

(ECHO LEVEL)******************************************************

A-1063-570-A MAIN BOARD, COMPLETE (TH)A-1063-678-A MAIN BOARD, COMPLETE (E3)A-1063-681-A MAIN BOARD, COMPLETE (E15)A-4752-308-A MAIN BOARD, COMPLETE (SP, MY)A-4752-374-A MAIN BOARD, COMPLETE (EA)A-4752-526-A MAIN BOARD, COMPLETE (AUS)A-4752-532-A MAIN BOARD, COMPLETE (E2)

******************

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

< CAPACITOR >

C1 1-126-964-11 ELECT 10uF 20% 50VC2 1-126-964-11 ELECT 10uF 20% 50VC3 1-124-261-00 ELECT 10uF 20% 50VC4 1-124-261-00 ELECT 10uF 20% 50V

C5 1-124-261-00 ELECT 10uF 20% 50V

C6 1-124-261-00 ELECT 10uF 20% 50VC19 1-124-259-11 ELECT 4.7uF 20% 50VC20 1-124-259-11 ELECT 4.7uF 20% 50VC21 1-126-965-91 ELECT 22uF 20% 50VC22 1-126-965-91 ELECT 22uF 20% 50V

C31 1-164-156-11 CERAMIC CHIP 0.1uF 25VC35 1-164-156-11 CERAMIC CHIP 0.1uF 25VC37 1-164-156-11 CERAMIC CHIP 0.1uF 25VC38 1-164-156-11 CERAMIC CHIP 0.1uF 25VC39 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C40 1-164-156-11 CERAMIC CHIP 0.1uF 25VC43 1-109-953-11 ELECT 2.2uF 20% 50VC101 1-126-964-11 ELECT 10uF 20% 50VC102 1-126-964-11 ELECT 10uF 20% 50VC103 1-126-964-11 ELECT 10uF 20% 50V

C104 1-126-964-11 ELECT 10uF 20% 50VC105 1-136-497-81 FILM 0.1uF 5% 50VC106 1-126-964-11 ELECT 10uF 20% 50VC107 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC108 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V

C109 1-126-964-11 ELECT 10uF 20% 50VC110 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC111 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25VC112 1-126-964-11 ELECT 10uF 20% 50VC113 1-137-194-81 FILM 0.47uF 5% 50V

C114 1-137-194-81 FILM 0.47uF 5% 50VC115 1-126-964-11 ELECT 10uF 20% 50VC116 1-126-964-11 ELECT 10uF 20% 50VC117 1-126-960-11 ELECT 1uF 20% 50VC118 1-130-483-00 MYLAR 0.01uF 5% 50V

C119 1-126-947-11 ELECT 47uF 20% 35VC120 1-124-261-00 ELECT 10uF 20% 50VC121 1-136-177-00 FILM 1uF 5% 50VC122 1-126-963-11 ELECT 4.7uF 20% 50VC123 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C124 1-104-658-91 ELECT 100uF 20% 10VC125 1-104-658-91 ELECT 100uF 20% 10VC126 1-104-658-91 ELECT 100uF 20% 10VC127 1-104-658-91 ELECT 100uF 20% 10VC128 1-126-964-11 ELECT 10uF 20% 50V

C129 1-137-194-81 FILM 0.47uF 5% 50VC130 1-130-491-00 MYLAR 0.047uF 5% 50VC131 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC132 1-130-483-00 MYLAR 0.01uF 5% 50VC133 1-130-483-00 MYLAR 0.01uF 5% 50V

C134 1-126-964-11 ELECT 10uF 20% 50VC135 1-126-960-11 ELECT 1uF 20% 50VC136 1-126-964-11 ELECT 10uF 20% 50VC137 1-137-194-81 FILM 0.47uF 5% 50VC138 1-137-190-91 FILM 0.22uF 5% 50V

C139 1-126-960-11 ELECT 1uF 20% 50VC140 1-126-960-11 ELECT 1uF 20% 50VC141 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC142 1-126-964-11 ELECT 10uF 20% 50VC143 1-162-960-11 CERAMIC CHIP 220PF 10% 50V

C144 1-126-964-11 ELECT 10uF 20% 50V

MAINHP

95

HCD-NXM4D


C146 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC147 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC148 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC149 1-126-964-11 ELECT 10uF 20% 50V

C150 1-163-077-00 CERAMIC CHIP 0.1uF 50VC151 1-126-964-11 ELECT 10uF 20% 50VC152 1-126-964-11 ELECT 10uF 20% 50VC154 1-126-964-11 ELECT 10uF 20% 50VC155 1-136-497-81 FILM 0.1uF 5% 50V

C156 1-126-964-11 ELECT 10uF 20% 50VC157 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC158 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC159 1-126-964-11 ELECT 10uF 20% 50VC160 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V

C161 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25VC162 1-126-964-11 ELECT 10uF 20% 50VC163 1-137-194-81 FILM 0.47uF 5% 50VC164 1-137-194-81 FILM 0.47uF 5% 50VC165 1-126-964-11 ELECT 10uF 20% 50V

C166 1-126-964-11 ELECT 10uF 20% 50VC167 1-126-960-11 ELECT 1uF 20% 50VC168 1-130-483-00 MYLAR 0.01uF 5% 50VC169 1-126-947-11 ELECT 47uF 20% 35VC170 1-124-261-00 ELECT 10uF 20% 50V

C173 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC174 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC183 1-126-961-11 ELECT 2.2uF 20% 50VC191 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC192 1-126-964-11 ELECT 10uF 20% 50V

C193 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC194 1-126-964-11 ELECT 10uF 20% 50VC196 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC197 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC198 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C199 1-126-964-11 ELECT 10uF 20% 50VC201 1-124-261-00 ELECT 10uF 20% 50VC202 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC203 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC204 1-124-261-00 ELECT 10uF 20% 50V

C205 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC206 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC207 1-124-261-00 ELECT 10uF 20% 50VC208 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC209 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C210 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC211 1-124-261-00 ELECT 10uF 20% 50VC212 1-124-261-00 ELECT 10uF 20% 50VC213 1-124-261-00 ELECT 10uF 20% 50VC220 1-124-261-00 ELECT 10uF 20% 50V

C221 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC222 1-124-261-00 ELECT 10uF 20% 50VC223 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC224 1-124-261-00 ELECT 10uF 20% 50VC226 1-126-160-11 ELECT 1uF 20% 50V

C228 1-137-190-91 FILM 0.22uF 5% 50VC229 1-136-497-81 FILM 0.1uF 5% 50VC233 1-125-972-91 ELECT 100uF 20% 16VC238 1-125-972-91 ELECT 100uF 20% 16V

C239 1-126-925-11 ELECT 470uF 20% 10V

C251 1-124-261-00 ELECT 10uF 20% 50VC252 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC253 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC254 1-124-261-00 ELECT 10uF 20% 50VC255 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C256 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC257 1-124-261-00 ELECT 10uF 20% 50VC258 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC259 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC260 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V



C277 1-124-261-00 ELECT 10uF 20% 50VC301 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC302 1-126-964-11 ELECT 10uF 20% 50VC303 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC304 1-126-964-11 ELECT 10uF 20% 50V

C305 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC306 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC307 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC308 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC311 1-130-481-00 MYLAR 0.0068uF 5% 50V

C312 1-130-483-00 MYLAR 0.01uF 5% 50VC313 1-126-947-11 ELECT 47uF 20% 35VC314 1-137-150-11 FILM 0.01uF 5% 100VC315 1-130-479-00 MYLAR 0.0047uF 5% 50VC322 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V

C324 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC351 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC352 1-126-964-11 ELECT 10uF 20% 50VC353 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC354 1-126-964-11 ELECT 10uF 20% 50V

C355 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC356 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC357 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC358 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC368 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C369 1-164-156-11 CERAMIC CHIP 0.1uF 25VC383 1-164-156-11 CERAMIC CHIP 0.1uF 25VC384 1-104-655-91 ELECT 470uF 20% 6.3VC390 1-126-965-91 ELECT 22uF 20% 50VC391 1-136-497-81 FILM 0.1uF 5% 50V

C392 1-136-497-81 FILM 0.1uF 5% 50VC393 1-126-964-11 ELECT 10uF 20% 50VC410 1-162-918-11 CERAMIC CHIP 18PF 5% 50VC411 1-162-918-11 CERAMIC CHIP 18PF 5% 50VC412 1-164-156-11 CERAMIC CHIP 0.1uF 25V


MAIN

96

HCD-NXM4D


C417 1-104-656-11 ELECT 2200uF 20% 6.3VC462 1-104-658-91 ELECT 100uF 20% 10VC463 1-164-156-11 CERAMIC CHIP 0.1uF 25VC475 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C476 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC497 1-164-156-11 CERAMIC CHIP 0.1uF 25VC498 1-126-964-11 ELECT 10uF 20% 50VC499 1-164-156-11 CERAMIC CHIP 0.1uF 25VC900 1-128-547-11 ELECT 6800 20% 16V

C901 1-126-956-91 ELECT 0.1uF 20% 50VC902 1-104-658-91 ELECT 100uF 20% 10VC903 1-126-964-11 ELECT 10uF 20% 50VC904 1-104-658-91 ELECT 100uF 20% 10VC905 1-126-956-91 ELECT 0.1uF 20% 50V

C906 1-104-658-91 ELECT 100uF 20% 10VC907 1-126-964-11 ELECT 10uF 20% 50VC908 1-126-767-11 ELECT 1000uF 20% 16VC910 1-126-767-11 ELECT 1000uF 20% 16VC911 1-165-718-21 ELECT 3300uF 20% 6.3V

C912 1-126-916-11 ELECT 1000uF 20% 6.3VC914 1-126-767-11 ELECT 1000uF 20% 16VC915 1-165-718-21 ELECT 3300uF 20% 6.3VC916 1-126-916-11 ELECT 1000uF 20% 6.3VC919 1-126-964-11 ELECT 10uF 20% 50V

C920 1-126-964-11 ELECT 10uF 20% 50VC930 1-126-768-11 ELECT 2200uF 20% 16VC952 1-164-156-11 CERAMIC CHIP 0.1uF 25VC953 1-164-156-11 CERAMIC CHIP 0.1uF 25V

< CONNECTOR >

CN101 1-691-769-11 PLUG (MICRO CONNECTOR) 7P* CN102 1-774-876-21 CONNECTOR, BOARD TO BOARD 8P

CN103 1-766-715-21 CONNECTOR, BOARD TO BOARD 10PCN104 1-785-318-11 PIN, CONNECTOR (STRAIGHT) 6PCN108 1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P

CN109 1-784-774-11 CONNECTOR, FFC 13PCN110 1-784-776-11 CONNECTOR, FFC 15PCN112 1-784-766-11 CONNECTOR, FFC 5PCN201 1-784-418-11 CONNECTOR, FFC (LIF (NON-ZIF) 21PCN202 1-779-275-11 CONNECTOR, FFC (LIF (NON-ZIF)) 7P

CN204 1-568-830-11 CONNECTOR, FFC 11P* CN301 1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P* CN302 1-564-724-11 PIN, CONNECTOR (SMALL TYPE) 8P

CN303 1-784-774-11 CONNECTOR, FFC 13PCN372 1-779-289-11 CONNECTOR, FFC (LIF (NON-ZIF)) 21P

< DIODE >



D394 8-719-988-61 DIODE 1SS355TE-17

D395 8-719-988-61 DIODE 1SS355TE-17D396 8-719-988-61 DIODE 1SS355TE-17D397 8-719-988-61 DIODE 1SS355TE-17D901 8-719-080-53 DIODE RK36LF-B3

D902 8-719-080-53 DIODE RK36LF-B3D903 6-500-522-31 DIODE 10EDB40-TB5D904 8-719-988-61 DIODE 1SS355TE-17D905 8-719-083-58 DIODE UDZSTE-173.9B

< EARTH TERMINAL >

EP901 1-537-738-21 TERMINAL, GROUND

< FERRITE BEAD >

FB30 1-469-125-21 FERRITE, EMI (SMD) (1608)FB34 1-469-125-21 FERRITE, EMI (SMD) (1608)FB50 1-469-125-21 FERRITE, EMI (SMD) (1608)FB54 1-469-125-21 FERRITE, EMI (SMD) (1608)FB80 1-469-125-21 FERRITE, EMI (SMD) (1608)

FB84 1-469-125-21 FERRITE, EMI (SMD) (1608)FB903 1-410-397-21 FERRITE 1.1uH

< IC >

IC101 6-705-667-01 IC M61537FP-RF0GIC201 6-703-651-11 IC M61530FP-D60GIC391 8-759-532-64 IC M62703SL-TPIC401 6-803-927-01 IC M3062CMEN-A01FPU0IC901 8-759-701-59 IC NJM78M09FA

IC902 8-759-701-59 IC NJM78M09FAIC903 8-759-231-53 IC TA7805SIC904 6-700-897-01 IC PQ12RD21IC905 6-700-812-01 IC SI-8050JFIC906 6-700-813-01 IC SI-8033JF

IC951 6-703-679-11 IC PT8300R-TP

< JACK >

J101 1-793-526-21 JACK, PIN 4P (VIDEO/SAT)

< SHORT >

JR7 1-216-864-11 SHORT CHIP 0JR101 1-216-864-11 SHORT CHIP 0JR102 1-216-864-11 SHORT CHIP 0JR103 1-216-296-11 SHORT CHIP 0JR104 1-216-296-11 SHORT CHIP 0



JR115 1-216-296-11 SHORT CHIP 0JR116 1-216-864-11 SHORT CHIP 0JR117 1-216-296-11 SHORT CHIP 0JR118 1-216-864-11 SHORT CHIP 0

MAIN

97

HCD-NXM4D


JR119 1-216-864-11 SHORT CHIP 0





JR449 1-216-864-11 SHORT CHIP 0

< COIL >

L301 1-410-780-11 INDUCTOR 27mHL311 1-414-189-31 INDUCTOR 100uHL351 1-410-780-11 INDUCTOR 27mHL901 1-456-468-11 INDUCTOR 100uHL902 1-414-398-11 INDUCTOR 10uH

L903 1-414-398-11 INDUCTOR 10uHL904 1-456-467-11 INDUCTOR 100uHL951 1-216-296-11 SHORT CHIP 0

< TRANSISTOR >

Q1 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ2 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ3 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ4 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ5 6-550-889-01 TRANSISTOR 2SC5938-T112-1B

Q6 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ19 8-729-027-43 TRANSISTOR DTC114EKA-T146Q20 8-729-027-23 TRANSISTOR DTA114EKA-T146Q21 8-729-027-43 TRANSISTOR DTC114EKA-T146Q22 8-729-027-23 TRANSISTOR DTA114EKA-T146

Q23 8-729-027-43 TRANSISTOR DTC114EKA-T146Q24 8-729-027-23 TRANSISTOR DTA114EKA-T146Q25 8-729-027-43 TRANSISTOR DTC114EKA-T146Q26 8-729-027-23 TRANSISTOR DTA114EKA-T146Q27 8-729-027-43 TRANSISTOR DTC114EKA-T146

Q28 8-729-027-23 TRANSISTOR DTA114EKA-T146Q29 8-729-027-43 TRANSISTOR DTC114EKA-T146Q30 8-729-027-23 TRANSISTOR DTA114EKA-T146Q31 8-729-027-43 TRANSISTOR DTC114EKA-T146Q32 8-729-027-23 TRANSISTOR DTA114EKA-T146

Q33 8-729-027-43 TRANSISTOR DTC114EKA-T146Q34 8-729-027-23 TRANSISTOR DTA114EKA-T146Q40 8-729-027-43 TRANSISTOR DTC114EKA-T146

Q101 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q102 6-550-889-01 TRANSISTOR 2SC5938-T112-1B

Q103 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ104 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ140 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ141 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ151 8-729-120-28 TRANSISTOR 2SC1623-L5L6



Q276 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ277 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ301 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q302 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q303 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16

Q311 8-729-216-22 TRANSISTOR 2SA1162-GQ312 8-729-027-43 TRANSISTOR DTC114EKA-T146Q313 8-729-027-43 TRANSISTOR DTC114EKA-T146Q314 8-729-027-23 TRANSISTOR DTA114EKA-T146Q315 8-729-027-43 TRANSISTOR DTC114EKA-T146

Q316 8-729-027-43 TRANSISTOR DTC114EKA-T146Q317 8-729-040-20 TRANSISTOR RT1P137L-TPQ318 8-729-142-46 TRANSISTOR 2SC2001-LKQ321 8-729-027-43 TRANSISTOR DTC114EKA-T146Q322 8-729-140-04 TRANSISTOR 2SB1116A-L

Q323 8-729-027-43 TRANSISTOR DTC114EKA-T146Q324 8-729-140-04 TRANSISTOR 2SB1116A-LQ326 8-729-027-43 TRANSISTOR DTC114EKA-T146Q327 8-729-140-04 TRANSISTOR 2SB1116A-LQ341 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Q342 8-729-027-43 TRANSISTOR DTC114EKA-T146Q343 8-729-027-43 TRANSISTOR DTC114EKA-T146Q351 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q352 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q353 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16

Q391 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q401 8-729-027-43 TRANSISTOR DTC114EKA-T146Q901 8-729-030-19 TRANSISTOR 2SB1640Q902 8-729-027-43 TRANSISTOR DTC114EKA-T146Q903 8-729-027-43 TRANSISTOR DTC114EKA-T146

Q904 8-729-027-43 TRANSISTOR DTC114EKA-T146Q906 8-729-120-28 TRANSISTOR 2SC1623-L5L6

< RESISTOR >

R1 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR2 1-216-833-11 METAL CHIP 10K 5% 1/10WR3 1-216-821-11 METAL CHIP 1K 5% 1/10WR4 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR5 1-216-833-11 METAL CHIP 10K 5% 1/10W

R6 1-216-821-11 METAL CHIP 1K 5% 1/10W

MAIN

98

HCD-NXM4D


R7 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR8 1-216-833-11 METAL CHIP 10K 5% 1/10WR9 1-216-821-11 METAL CHIP 1K 5% 1/10WR10 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R11 1-216-833-11 METAL CHIP 10K 5% 1/10WR12 1-216-821-11 METAL CHIP 1K 5% 1/10WR13 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR14 1-216-833-11 METAL CHIP 10K 5% 1/10WR15 1-216-821-11 METAL CHIP 1K 5% 1/10W



R26 1-216-845-11 METAL CHIP 100K 5% 1/10WR27 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10WR28 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10WR29 1-216-845-11 METAL CHIP 100K 5% 1/10WR30 1-216-864-11 SHORT CHIP 0



R43 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR45 1-216-845-11 METAL CHIP 100K 5% 1/10WR79 1-216-864-11 SHORT CHIP 0R89 1-216-864-11 SHORT CHIP 0R101 1-216-835-11 METAL CHIP 15K 5% 1/10W

R102 1-216-841-11 METAL CHIP 47K 5% 1/10WR103 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR104 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR105 1-216-833-11 METAL CHIP 10K 5% 1/10WR106 1-216-833-11 METAL CHIP 10K 5% 1/10W


R112 1-216-834-11 METAL CHIP 12K 5% 1/10WR113 1-216-851-11 METAL CHIP 330K 5% 1/10WR114 1-216-812-11 METAL CHIP 180 5% 1/10WR115 1-216-821-11 METAL CHIP 1K 5% 1/10WR116 1-216-841-11 METAL CHIP 47K 5% 1/10W

R117 1-216-833-11 METAL CHIP 10K 5% 1/10WR118 1-216-809-11 METAL CHIP 100 5% 1/10WR119 1-216-833-11 METAL CHIP 10K 5% 1/10WR120 1-216-833-11 METAL CHIP 10K 5% 1/10W

R121 1-216-861-11 METAL CHIP 2.2M 5% 1/10W

R122 1-216-835-11 METAL CHIP 15K 5% 1/10WR123 1-216-857-11 METAL CHIP 1M 5% 1/10WR124 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR125 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR126 1-216-833-11 METAL CHIP 10K 5% 1/10W

R127 1-216-833-11 METAL CHIP 10K 5% 1/10WR128 1-216-857-11 METAL CHIP 1M 5% 1/10WR129 1-216-835-11 METAL CHIP 15K 5% 1/10WR130 1-216-809-11 METAL CHIP 100 5% 1/10WR131 1-216-825-11 METAL CHIP 2.2K 5% 1/10W



R153 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR154 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR155 1-216-833-11 METAL CHIP 10K 5% 1/10WR156 1-216-833-11 METAL CHIP 10K 5% 1/10WR157 1-216-815-11 METAL CHIP 330 5% 1/10W


R163 1-216-851-11 METAL CHIP 330K 5% 1/10WR164 1-216-812-11 METAL CHIP 180 5% 1/10WR165 1-216-821-11 METAL CHIP 1K 5% 1/10WR166 1-216-841-11 METAL CHIP 47K 5% 1/10WR167 1-216-833-11 METAL CHIP 10K 5% 1/10W

R168 1-216-809-11 METAL CHIP 100 5% 1/10WR169 1-216-833-11 METAL CHIP 10K 5% 1/10WR180 1-216-809-11 METAL CHIP 100 5% 1/10WR186 1-216-864-11 SHORT CHIP 0R187 1-216-853-11 METAL CHIP 470K 5% 1/10W



R203 1-216-833-11 METAL CHIP 10K 5% 1/10WR204 1-216-821-11 METAL CHIP 1K 5% 1/10WR205 1-216-833-11 METAL CHIP 10K 5% 1/10WR206 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR207 1-216-841-11 METAL CHIP 47K 5% 1/10W

R208 1-216-841-11 METAL CHIP 47K 5% 1/10W

MAIN

99

HCD-NXM4D


R209 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR210 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR211 1-216-841-11 METAL CHIP 47K 5% 1/10WR212 1-216-857-11 METAL CHIP 1M 5% 1/10W

R213 1-216-864-11 SHORT CHIP 0R220 1-216-821-11 METAL CHIP 1K 5% 1/10WR221 1-216-833-11 METAL CHIP 10K 5% 1/10WR222 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR223 1-216-841-11 METAL CHIP 47K 5% 1/10W


(E2)

R241 1-216-864-11 SHORT CHIP 0 (EXCEPT E2)R242 1-216-845-11 METAL CHIP 100K 5% 1/10W

(E2)R243 1-216-833-11 METAL CHIP 10K 5% 1/10W

(E2)R243 1-216-864-11 SHORT CHIP 0 (EXCEPT E2)R244 1-216-845-11 METAL CHIP 100K 5% 1/10W

(E2)



R259 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR260 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR261 1-216-841-11 METAL CHIP 47K 5% 1/10WR262 1-216-857-11 METAL CHIP 1M 5% 1/10WR263 1-216-864-11 SHORT CHIP 0


R275 1-216-821-11 METAL CHIP 1K 5% 1/10WR276 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR277 1-216-833-11 METAL CHIP 10K 5% 1/10WR278 1-216-821-11 METAL CHIP 1K 5% 1/10WR279 1-216-825-11 METAL CHIP 2.2K 5% 1/10W



R290 1-216-821-11 METAL CHIP 1K 5% 1/10WR291 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR292 1-216-833-11 METAL CHIP 10K 5% 1/10WR293 1-216-821-11 METAL CHIP 1K 5% 1/10WR301 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R302 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR303 1-216-821-11 METAL CHIP 1K 5% 1/10WR304 1-216-835-11 METAL CHIP 15K 5% 1/10WR305 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR306 1-216-832-11 METAL CHIP 8.2K 5% 1/10W


R314 1-216-841-11 METAL CHIP 47K 5% 1/10WR315 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR316 1-216-797-11 METAL CHIP 10 5% 1/10WR317 1-216-833-11 METAL CHIP 10K 5% 1/10WR318 1-216-805-11 METAL CHIP 47 5% 1/10W

R319 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR320 1-216-803-11 METAL CHIP 33 5% 1/10WR321 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR322 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR323 1-216-821-11 METAL CHIP 1K 5% 1/10W

R324 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR325 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR326 1-216-821-11 METAL CHIP 1K 5% 1/10WR327 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR328 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R329 1-216-841-11 METAL CHIP 47K 5% 1/10WR330 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR331 1-216-841-11 METAL CHIP 47K 5% 1/10WR332 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR333 1-216-841-11 METAL CHIP 47K 5% 1/10W


R339 1-216-841-11 METAL CHIP 47K 5% 1/10WR340 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR341 1-216-833-11 METAL CHIP 10K 5% 1/10WR342 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR343 1-216-837-11 METAL CHIP 22K 5% 1/10W

R344 1-216-833-11 METAL CHIP 10K 5% 1/10WR345 1-216-833-11 METAL CHIP 10K 5% 1/10WR347 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR351 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR352 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R353 1-216-821-11 METAL CHIP 1K 5% 1/10WR354 1-216-835-11 METAL CHIP 15K 5% 1/10WR355 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR356 1-216-832-11 METAL CHIP 8.2K 5% 1/10WR357 1-216-833-11 METAL CHIP 10K 5% 1/10W

R359 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR377 1-216-833-11 METAL CHIP 10K 5% 1/10WR378 1-216-833-11 METAL CHIP 10K 5% 1/10W

MAIN

100

HCD-NXM4D





R393 1-216-837-11 METAL CHIP 22K 5% 1/10WR394 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR395 1-216-813-11 METAL CHIP 220 5% 1/10WR396 1-216-833-11 METAL CHIP 10K 5% 1/10WR400 1-216-833-11 METAL CHIP 10K 5% 1/10W

R404 1-216-809-11 METAL CHIP 100 5% 1/10WR406 1-216-809-11 METAL CHIP 100 5% 1/10WR407 1-216-809-11 METAL CHIP 100 5% 1/10WR408 1-216-833-11 METAL CHIP 10K 5% 1/10WR409 1-216-833-11 METAL CHIP 10K 5% 1/10W

R410 1-216-833-11 METAL CHIP 10K 5% 1/10WR411 1-216-851-11 METAL CHIP 330K 5% 1/10WR412 1-216-833-11 METAL CHIP 10K 5% 1/10WR413 1-216-864-11 SHORT CHIP 0R414 1-216-833-11 METAL CHIP 10K 5% 1/10W

R415 1-216-833-11 METAL CHIP 10K 5% 1/10WR416 1-216-833-11 METAL CHIP 10K 5% 1/10WR417 1-216-833-11 METAL CHIP 10K 5% 1/10WR419 1-216-864-11 SHORT CHIP 0R420 1-216-829-11 METAL CHIP 4.7K 5% 1/10W











R490 1-216-809-11 METAL CHIP 100 5% 1/10WR492 1-216-821-11 METAL CHIP 1K 5% 1/10W

(E2)R492 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

(EXCEPT E2)R493 1-216-809-11 METAL CHIP 100 5% 1/10WR494 1-216-827-11 METAL CHIP 3.3K 5% 1/10W

R495 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR496 1-216-815-11 METAL CHIP 330 5% 1/10W

(E3, E15)R496 1-216-821-11 METAL CHIP 1K 5% 1/10W

(EA)R496 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

(AUS)R496 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

(E2)

R496 1-216-864-11 SHORT CHIP 0 (SP, MY, TH)R497 1-216-833-11 METAL CHIP 10K 5% 1/10WR498 1-216-797-11 METAL CHIP 10 5% 1/10WR499 1-216-797-11 METAL CHIP 10 5% 1/10WR901 1-216-833-11 METAL CHIP 10K 5% 1/10W

R902 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR903 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR904 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR905 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR906 1-216-809-11 METAL CHIP 100 5% 1/10W

R907 1-216-837-11 METAL CHIP 22K 5% 1/10WR908 1-216-809-11 METAL CHIP 100 5% 1/10WR909 1-216-833-11 METAL CHIP 10K 5% 1/10WR914 1-216-821-11 METAL CHIP 1K 5% 1/10WR915 1-216-821-11 METAL CHIP 1K 5% 1/10W

R952 1-216-809-11 METAL CHIP 100 5% 1/10WR955 1-216-809-11 METAL CHIP 100 5% 1/10WR956 1-216-809-11 METAL CHIP 100 5% 1/10WR957 1-216-809-11 METAL CHIP 100 5% 1/10W

MAIN

101

HCD-NXM4D


R958 1-216-809-11 METAL CHIP 100 5% 1/10W

R959 1-216-809-11 METAL CHIP 100 5% 1/10WR969 1-216-833-11 METAL CHIP 10K 5% 1/10WR970 1-216-833-11 METAL CHIP 10K 5% 1/10W

< TRANSFORMER >

T301 1-433-372-11 TRANSFORMER, BIAS OSCILLATION

< VIBRATOR >

X401 1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)X402 1-795-482-11 VIBRATOR, CERAMIC (16MHz)

******************************************************

MOTOR BOARD***********

< SWITCH >

S761 1-786-704-11 SWITCH, LEVER (SUB TRY OUT)*******************************************************

A-1063-578-A PANEL BOARD, COMPLETE (TH)A-4752-675-A PANEL BOARD, COMPLETE (EXCEPT TH)

*******************

< CAPACITOR >

C1006 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1021 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC1022 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC1023 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC1024 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C1025 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC1026 1-126-964-11 ELECT 10uF 20% 50VC1028 1-126-964-11 ELECT 10uF 20% 50VC1029 1-131-992-91 CERAMIC CHIP 100000PF 35VC1048 1-131-992-91 CERAMIC CHIP 100000PF 35V

C1050 1-162-974-11 CERAMIC CHIP 0.01uF 50VC1051 1-126-969-11 ELECT 220uF 20% 50VC1052 1-162-974-11 CERAMIC CHIP 0.01uF 50VC1053 1-126-965-91 ELECT 22uF 20% 50VC1054 1-162-995-11 CERAMIC CHIP 0.022uF 50V

< CONNECTOR >

CN1021 1-784-774-11 CONNECTOR, FFC 13P

< DIODE >

D1021 8-719-058-03 DIODE SEL5423E-TP15 (bB)D1022 8-719-059-18 DIODE RD6.2FM-T1D1023 8-719-988-61 DIODE 1SS355TE-17D1024 8-719-988-61 DIODE 1SS355TE-17D1025 8-719-988-61 DIODE 1SS355TE-17

D1026 8-719-988-61 DIODE 1SS355TE-17

< FLUORESCENT INDICATOR >

FL1020 1-518-979-11 INDICATOR TUBE, FLUORESCENT

< IC >

IC1020 6-705-745-01 IC M66005-0131AHPRB0T

< COIL >

L1021 1-410-671-31 INDUCTOR 47uH

< TRANSISTOR >

Q1021 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q1022 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q1023 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q1024 6-550-065-01 TRANSISTOR CPH5504-TL-EQ1026 8-729-027-43 TRANSISTOR DTC114EKA-T146

< RESISTOR >

R1020 1-216-809-11 METAL CHIP 100 5% 1/10WR1021 1-216-821-11 METAL CHIP 1K 5% 1/10WR1022 1-216-809-11 METAL CHIP 100 5% 1/10WR1023 1-216-809-11 METAL CHIP 100 5% 1/10WR1024 1-216-821-11 METAL CHIP 1K 5% 1/10W

R1025 1-216-833-11 METAL CHIP 10K 5% 1/10WR1026 1-216-813-11 METAL CHIP 220 5% 1/10WR1027 1-216-815-11 METAL CHIP 330 5% 1/10WR1028 1-216-817-11 METAL CHIP 470 5% 1/10WR1029 1-216-819-11 METAL CHIP 680 5% 1/10W

R1030 1-216-821-11 METAL CHIP 1K 5% 1/10WR1031 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR1032 1-216-864-11 SHORT CHIP 0R1033 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR1034 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R1035 1-216-833-11 METAL CHIP 10K 5% 1/10WR1036 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR1037 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR1038 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1039 1-216-833-11 METAL CHIP 10K 5% 1/10W

R1040 1-216-839-11 METAL CHIP 33K 5% 1/10WR1041 1-216-845-11 METAL CHIP 100K 5% 1/10WR1042 1-216-845-11 METAL CHIP 100K 5% 1/10WR1043 1-216-845-11 METAL CHIP 100K 5% 1/10WR1045 1-216-827-11 METAL CHIP 3.3K 5% 1/10W

R1046 1-216-833-11 METAL CHIP 10K 5% 1/10WR1051 1-216-809-11 METAL CHIP 100 5% 1/10WR1052 1-216-809-11 METAL CHIP 100 5% 1/10WR1096 1-215-871-11 METAL OXIDE 2.2K 5% 1WR1100 1-216-833-11 METAL CHIP 10K 5% 1/10W


< SWITCH >

S1021 1-762-875-21 SWITCH, KEYBOARD (DVD)S1022 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)S1023 1-762-875-21 SWITCH, KEYBOARD (TAPE A/B)S1024 1-762-875-21 SWITCH, KEYBOARD (VIDEO (MD))S1025 1-762-875-21 SWITCH, KEYBOARD (DIMMER)

S1026 1-762-875-21 SWITCH, KEYBOARD (CD SYNC)S1027 1-762-875-21 SWITCH, KEYBOARD (z /START)S1028 1-762-875-21 SWITCH, KEYBOARD (DISPLAY)S1029 1-762-875-21 SWITCH, KEYBOARD (bB)

MAIN PANELMOTOR

102

HCD-NXM4D


S1030 1-762-875-21 SWITCH, KEYBOARD (DVD Z)

S1031 1-762-875-21 SWITCH, KEYBOARD (X)S1032 1-762-875-21 SWITCH, KEYBOARD (M> TUNING +)S1033 1-762-875-21 SWITCH, KEYBOARD (.mTUNING -)S1034 1-762-875-21 SWITCH, KEYBOARD (ALBUM +)S1035 1-762-875-21 SWITCH, KEYBOARD (ALBUM -)

S1036 1-762-875-21 SWITCH, KEYBOARD (x)

< TRANSFORMER >

T801 1-443-285-11 TRANSFORMER, DC-DC CONVERTER*******************************************************

A-4750-232-A RELAY BOARD, COMPLETE*******************

< CAPACITOR >

C701 1-126-786-11 ELECT 47uF 20% 16VC702 1-126-791-11 ELECT 10uF 20% 35VC761 1-162-306-11 CERAMIC 0.01uF 20% 16VC762 1-162-306-11 CERAMIC 0.01uF 20% 16V

< CONNECTOR >

CN701 1-779-558-21 CONNECTOR, FFC (LIF (NON-ZIF)) 21P

< DIODE >

D701 8-719-921-40 DIODE MTZJ-4.7CD711 8-719-982-10 DIODE MTZJ-4.3A

< IC >

IC701 8-759-598-69 IC BA6956ANIC711 8-759-598-69 IC BA6956AN

< TRANSISTOR >

Q751 8-729-119-78 TRANSISTOR 2SC2785-HFE

< RESISTOR >

R701 1-249-415-11 CARBON 680 5% 1/4WR702 1-247-807-31 CARBON 100 5% 1/4WR711 1-249-415-11 CARBON 680 5% 1/4WR712 1-247-807-31 CARBON 100 5% 1/4WR751 1-247-806-11 CARBON 91 5% 1/4W

R752 1-249-429-11 CARBON 10K 5% 1/4WR753 1-249-429-11 CARBON 10K 5% 1/4WR754 1-249-430-11 CARBON 12K 5% 1/4WR755 1-249-429-11 CARBON 10K 5% 1/4W

******************************************************

A-4728-690-A RF BOARD, COMPLETE****************

< CAPACITOR >

C001 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC002 1-124-779-00 ELECT CHIP 10uF 20% 16VC003 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC004 1-124-779-00 ELECT CHIP 10uF 20% 16VC005 1-128-993-21 ELECT CHIP 22uF 20% 10V

C006 1-128-993-21 ELECT CHIP 22uF 20% 10V



C017 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC018 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25VC019 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25VC020 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC021 1-162-919-11 CERAMIC CHIP 22PF 5% 50V

C022 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC023 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC024 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC025 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC026 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V



C037 1-115-412-11 CERAMIC CHIP 680PF 5% 25VC038 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC039 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC040 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC041 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C042 1-164-218-11 CERAMIC CHIP 180PF 5% 50VC049 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC050 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC051 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC052 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< CONNECTOR >

CN001 1-815-031-11 CONNECTOR, FFC/FPC (ZIF) 24PCN002 1-784-836-21 CONNECTOR, FFC (LIF (NON-ZIF)) 29PCN003 1-784-861-21 CONNECTOR, FFC (LIF (NON-ZIF)) 9P

< DIODE >

D001 8-719-988-61 DIODE 1SS355TE-17D002 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC001 6-703-922-01 IC SP3723CAF0PMIC003 6-703-921-01 IC TL343IDBVR

< COIL >

L001 1-412-031-11 INDUCTOR 47uHL002 1-412-031-11 INDUCTOR 47uH

RELAYPANEL RF

103

HCD-NXM4D


< TRANSISTOR >

Q001 8-729-903-46 TRANSISTOR 2SB1132-PQ002 8-729-903-46 TRANSISTOR 2SB1132-P

< RESISTOR >

R001 1-218-668-11 METAL CHIP 100 0.5% 1/10WR003 1-216-803-11 METAL CHIP 33 5% 1/10WR004 1-216-803-11 METAL CHIP 33 5% 1/10WR005 1-216-841-11 METAL CHIP 47K 5% 1/10WR006 1-216-817-11 METAL CHIP 470 5% 1/10W

R007 1-216-803-11 METAL CHIP 33 5% 1/10WR008 1-216-803-11 METAL CHIP 33 5% 1/10WR009 1-216-841-11 METAL CHIP 47K 5% 1/10WR010 1-216-817-11 METAL CHIP 470 5% 1/10WR011 1-216-864-11 SHORT CHIP 0



R022 1-216-813-11 METAL CHIP 220 5% 1/10WR023 1-216-820-11 METAL CHIP 820 5% 1/10WR024 1-216-864-11 SHORT CHIP 0R025 1-216-809-11 METAL CHIP 100 5% 1/10WR026 1-218-718-11 METAL CHIP 12K 0.5% 1/10W

R027 1-216-864-11 SHORT CHIP 0R028 1-216-864-11 SHORT CHIP 0R029 1-216-864-11 SHORT CHIP 0R031 1-216-809-11 METAL CHIP 100 5% 1/10WR033 1-216-845-11 METAL CHIP 100K 5% 1/10W

R034 1-216-817-11 METAL CHIP 470 5% 1/10WR035 1-216-864-11 SHORT CHIP 0R041 1-216-821-11 METAL CHIP 1K 5% 1/10WR046 1-216-833-11 METAL CHIP 10K 5% 1/10WR047 1-216-839-11 METAL CHIP 33K 5% 1/10W

R091 1-218-913-91 METAL CHIP 560K 0.5% 1/10W******************************************************

SENSOR BOARD************

< IC >

IC751 8-759-989-76 IC RPR-359F************************************************************

A-1063-586-A SUR AMP BOARD, COMPLETE (TH)A-4752-320-A SUR AMP BOARD, COMPLETE (EXCEPT TH)

**********************

< CAPACITOR >

C601 1-126-961-11 ELECT 2.2uF 20% 50VC602 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC603 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C604 1-126-947-11 ELECT 47uF 20% 35VC605 1-126-961-11 ELECT 2.2uF 20% 50V

C606 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC607 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC608 1-126-947-11 ELECT 47uF 20% 35VC609 1-126-961-11 ELECT 2.2uF 20% 50VC610 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C611 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC612 1-126-947-11 ELECT 47uF 20% 35VC614 1-130-777-00 MYLAR 0.1uF 10% 100VC615 1-130-777-00 MYLAR 0.1uF 10% 100VC617 1-130-777-00 MYLAR 0.1uF 10% 100V

C618 1-130-777-00 MYLAR 0.1uF 10% 100VC620 1-130-777-00 MYLAR 0.1uF 10% 100VC621 1-130-777-00 MYLAR 0.1uF 10% 100VC622 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC623 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C624 1-126-965-91 ELECT 22uF 20% 50VC650 1-162-974-11 CERAMIC CHIP 0.01uF 50V

< CONNECTOR >

CN601 1-785-332-11 PIN, CONNECTOR (LIGHT ANGLE) 6P

< DIODE >


D604 8-719-988-61 DIODE 1SS355TE-17

< EARTH TERMINAL >

* EP601 1-537-738-21 TERMINAL, EARTH* EP602 1-537-738-21 TERMINAL, EARTH

< IC >

IC601 6-600-173-01 IC STK403-240A

< TRANSISTOR >

Q601 8-729-140-84 TRANSISTOR 2SC1841-PAFAEAQ602 8-729-140-84 TRANSISTOR 2SC1841-PAFAEAQ603 8-729-140-84 TRANSISTOR 2SC1841-PAFAEAQ610 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16

< RESISTOR >

R602 1-216-821-11 METAL CHIP 1K 5% 1/10WR603 1-216-841-11 METAL CHIP 47K 5% 1/10WR604 1-216-818-11 METAL CHIP 560 5% 1/10W


R608 1-216-841-11 METAL CHIP 47K 5% 1/10WR609 1-218-482-11 METAL CHIP 430 5% 1/10W



SENSORRF SUR AMP

104

HCD-NXM4D


R613 1-216-841-11 METAL CHIP 47K 5% 1/10W

R614 1-218-482-11 METAL CHIP 430 5% 1/10W0R615 1-220-755-11 METAL 0.22 10% 2W

R616 1-216-841-11 METAL CHIP 47K 5% 1/10WR617 1-216-821-11 METAL CHIP 1K 5% 1/10WR618 1-216-835-11 METAL CHIP 15K 5% 1/10W

R620 1-249-625-31 CARBON 10 5% 1/2WR621 1-216-841-11 METAL CHIP 47K 5% 1/10WR622 1-216-821-11 METAL CHIP 1K 5% 1/10WR623 1-216-835-11 METAL CHIP 15K 5% 1/10WR625 1-249-625-31 CARBON 10 5% 1/2W

R626 1-216-841-11 METAL CHIP 47K 5% 1/10WR627 1-216-821-11 METAL CHIP 1K 5% 1/10WR628 1-216-835-11 METAL CHIP 15K 5% 1/10WR629 1-216-845-11 METAL CHIP 100K 5% 1/10WR630 1-249-625-31 CARBON 10 5% 1/2W

R635 1-216-833-11 METAL CHIP 10K 5% 1/10WR652 1-216-833-11 METAL CHIP 10K 5% 1/10WR653 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

0R656 1-245-605-51 FUSIBLE 100 5% 1/4WR657 1-216-845-11 METAL CHIP 100K 5% 1/10W

R658 1-216-845-11 METAL CHIP 100K 5% 1/10WR661 1-216-843-11 METAL CHIP 68K 5% 1/10WR662 1-216-841-11 METAL CHIP 47K 5% 1/10WR663 1-216-843-11 METAL CHIP 68K 5% 1/10W

0R670 1-217-637-00 FUSIBLE 1 5% 1/4W

0R680 1-215-863-11 METAL OXIDE 100 5% 1W0R681 1-215-863-11 METAL OXIDE 100 5% 1W

< RELAY >

RY601 1-755-421-11 RELAYRY602 1-755-421-11 RELAY

******************************************************

SW (1) BOARD***********

< SWITCH >

S721 1-786-084-11 SWITCH, DETECTION (MAIN TRY IN/OUT)******************************************************

SW (2) BOARD***********

< SWITCH >

S731 1-786-382-11 SWITCH, PUSH (1 KEY) (SUB RTY IN)******************************************************

A-1063-575-A VIDEO BOARD, COMPLETE (TH)A-4752-312-A VIDEO BOARD, COMPLETE (EXCEPT TH)

*******************

< CAPACITOR >

C1101 1-126-960-11 ELECT 1uF 20% 50VC1102 1-126-960-11 ELECT 1uF 20% 50VC1103 1-126-960-11 ELECT 1uF 20% 50VC1104 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1105 1-126-965-91 ELECT 22uF 20% 50V

C1106 1-126-960-11 ELECT 1uF 20% 50VC1107 1-126-960-11 ELECT 1uF 20% 50VC1108 1-126-960-11 ELECT 1uF 20% 50VC1109 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1110 1-104-658-91 ELECT 100uF 20% 10V

C1111 1-126-916-11 ELECT 1000uF 20% 6.3VC1112 1-126-916-11 ELECT 1000uF 20% 6.3VC1113 1-126-916-11 ELECT 1000uF 20% 6.3VC1114 1-126-916-11 ELECT 1000uF 20% 6.3VC1115 1-126-916-11 ELECT 1000uF 20% 6.3V

C1116 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1117 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC1118 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC1119 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC1120 1-216-864-11 SHORT CHIP 0

C1121 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC1122 1-216-864-11 SHORT CHIP 0C1123 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC1124 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC1125 1-216-864-11 SHORT CHIP 0

< CONNECTOR >

CN1101 1-779-285-11 CONNECTOR, FFC (LIF (NON-ZIF)) 17P

< EARTH TERMINAL >

EP1101 1-537-738-21 TERMINAL, GROUNDEP1102 1-537-738-21 TERMINAL, GROUND

< FERRITE BEAD >

FB1101 1-216-864-11 SHORT CHIP 0FB1102 1-216-864-11 SHORT CHIP 0FB1103 1-216-864-11 SHORT CHIP 0FB1104 1-216-864-11 SHORT CHIP 0FB1105 1-216-864-11 SHORT CHIP 0

FB1106 1-216-864-11 SHORT CHIP 0

< IC >

IC1101 6-705-602-01 IC MM1623BFBE

< JACK >

J1101 1-537-943-11 TERMINAL, S (S VIDEO OUT)J1102 1-785-867-11 JACK, PIN 1P (VIDEO OUT)J1103 1-793-483-11 PHONO JACK 3P (COMPONENT VIDEO OUT)

< COIL >

L1101 1-412-058-11 INDUCTOR 10uH

< TRANSISTOR >

Q1101 8-729-027-43 TRANSISTOR DTC114EKA-T146

< RESISTOR >

R1101 1-216-833-11 METAL CHIP 10K 5% 1/10W


SW (1) SW (2)SUR AMP VIDEO

105

HCD-NXM4D


R1102 1-216-809-11 METAL CHIP 100 5% 1/10WR1103 1-216-833-11 METAL CHIP 10K 5% 1/10WR1104 1-218-285-11 METAL CHIP 75 5% 1/10WR1105 1-218-285-11 METAL CHIP 75 5% 1/10W


R1111 1-218-285-11 METAL CHIP 75 5% 1/10WR1112 1-216-833-11 METAL CHIP 10K 5% 1/10W

************************************************************

A-1063-580-A VOL BOARD, COMPLETE (TH)A-4752-315-A VOL BOARD, COMPLETE (EXCEPT TH)

******************

< CAPACITOR >

C1007 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1008 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1013 1-126-947-11 ELECT 47uF 20% 35V

< CONNECTOR >

CN1050 1-784-776-11 CONNECTOR, FFC 15PCN1051 1-784-766-11 CONNECTOR, FFC 5P

< DIODE >

D1050 8-719-071-44 DIODE SELS5223C-TP15D1051 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC1050 6-600-349-31 IC NJL24H400A

< TRANSISTOR >

Q1041 8-729-027-43 TRANSISTOR DTC114EKA-T146

< RESISTOR >

R1048 1-216-864-11 SHORT CHIP 0R1049 1-216-821-11 METAL CHIP 1K 5% 1/10WR1050 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR1059 1-216-805-11 METAL CHIP 47 5% 1/10WR1090 1-216-821-11 METAL CHIP 1K 5% 1/10W


< SWITCH >

S1042 1-762-875-21 SWITCH, KEYBOARD (\/1)S1043 1-762-875-21 SWITCH, KEYBOARD (DSGX)S1050 1-786-418-11 SWITCH, ROTARY (ENCODER) (SOUND MODE)S1051 1-786-418-11 SWITCH, ROTARY (ENCODER) (SOUND SELECT)S1052 1-418-725-51 ENCODER, ROTARY (12 TYPE) (VOLUME)

******************************************************

MISCELLANEOUS*************

3 1-769-984-11 WIRE (FLAT TYPE) (13 CORE) (EXCEPT TH)4 1-765-333-11 WIRE (FLAT TYPE) (15 CORE) (EXCEPT TH)5 1-769-872-11 WIRE (FLAT TYPE) (5 CORE) (EXCEPT TH)6 1-769-939-11 WIRE (FLAT TYPE) (11 CORE) (EXCEPT TH)59 1-796-880-11 DECK, MECHANISM (W)

0102 1-468-817-11 REGULATOR, SWITCHING0103 1-775-786-21 CORD, POWER (EA)0103 1-775-790-22 CORD, POWER (AUS)0103 1-777-071-53 CORD, POWER (SP, MY)0103 1-824-818-11 CORD, POWER (WITH CONNECTOR) (TH)

0103 1-827-226-11 CORD, POWER (E2, E3, E15)109 1-500-497-11 FILTER, CLAMP (FERRITE CORE)110 1-543-830-11 CLAMP, SLEEVE FERRITE111 1-500-657-11 CORE, FERRITE

0302 A-1067-676-A OPTICAL PICK-UP SERVICE ASSY, DBU-3

305 1-824-106-12 CABLE, FLEXIBLE FLAT (24 CORE)M761 A-4713-174-A MOTOR (81) ASSY (LD/ST MOTOR)M762 A-4713-174-A MOTOR (81) ASSY (BU U/D MOTOR)M961 1-787-099-11 FAN, DCM962 1-787-021-11 FAN, DC

S771 1-478-552-11 ENCODER, ROTARYS781 1-478-551-11 ENCODER, ROTARY


VOLVIDEOVer. 1.2

106

HCD-NXM4D

MEMO

SERVICE MANUALE Model

Australian Model

9-877-971-81

Ver. 1.1

HCD-NXM4D

SUPPLEMENT-1

Subject: CDM81 DISASSEMBLY

2

HCD-NXM4D

1-1. DISASSEMBLY FLOW

3-14.BASE UNIT (DVBU60)(See page 15 of Service Manual)

1-2.GEAR (SUB TRAY 1), GEAR (SUB TRAY 2)

(Page 3)

1-3.LEVER ASSY(Page 3)

1-4.STOCKER SECTION(Page 4)

1-7.ROTARY ENCODER (MD)(Page 5)

1-5.CAM (STOCKER)(Page 4)

1-8.GEAR (BU1)(Page 6)

1-6.GEAR (STOCKER 3)(Page 5)

• This set can be disassembled in the order shown below.• The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square

( ) are completed.

SECTION 1CDM81 DISASSEMBLY

3

HCD-NXM4D

1-2. GEAR (SUB TRAY 1), GEAR (SUB TRAY 2)

1-3. LEVER ASSY

1 five screws (+PTPWH 2.6 × 8)

2 gear (sub tray 2)

3 gear (sub tray 2)

4 three gears (sub tray 1)

gear (sub tray 2)

gear (sub tray 2)

gear (sub tray 1)

PRECAUTION DURING GEAR (SUB TRAY 1/2) INSTALLATION

Align the marks of the gears as shown in the illustration.

1 screw (+PTPWH 2.6 × 8)

3 floating screw (+PTPWH M2.6)

5 lever (sub tray)

lever (sub tray)

6 lever (release)

lever (release)

7 lever (mode)

cam (BU)

lever (mode)

2 shutter (tray)

4

lever (sub tray)shutter (tray)

When re-assembling, insert the lever (sub tray)between the bosses of the shutter (tray).

boss

boss

Before re-assembling, slide the cam (BU) in the direction of the arrow.

Before re-assembling, align the lever (release) and the lever (sub tray) with the lever (mode) as shown in the illustration.

dowel dowel

4

HCD-NXM4D

1-4. STOCKER SECTION

1-5. CAM (STOCKER)

2 stocker section

1 Rotate the gear (SS3) in the direction of the arrow.

5 two screws (+PTPWH 2.6 × 8)

6 two cams (stocker)

8 cam (stocker)

cam (stocker)cam (stocker)

cam (stocker)

holegear (stocker 2)

gear (stocker 2)

gear (stocker 2)

gear (stocker 3)

2 tension spring (SW)

4 lever (SW)1 screw (+PTPWH 2.6 × 8)


3 hook

PRECAUTION DURING CAM (STOCKER) INSTALLATION

Before installing the cams (stocker), fix the gear (stocker 3) inthe manner so that the hole of the gear (stocker 3) should bealigned with the hole of the chassis located beneath the gear (stocker 3). Be sure to install the cams (stocker) in such a way that the grooves of the cams (stocker) face the direction of the arrows.

5

HCD-NXM4D

1-6. GEAR (STOCKER 3)

1-7. ROTARY ENCODER (MD)


2 gear (stocker 3)

gear (stocker 3)(reverse-side)

rotary encoder (ST U/D encoder)

PRECAUTION DURING GEAR (STOCKER 3) INSTALLATION

Be sure to align the rib of the gear (stocker 3) with the grooveof the rotary encoder.

groove

rib

1 three screws (+BTP 2.6 × 8)

2 rotary encoder (MD)

rotary encoder (MD)

gear (BU1)

PRECAUTION DURING ROTARY ENCODER (MD) INSTALLATION

cam (BU)

Slide the cam (BU) in the direction of the arrow so that the markof the gear (BU1) can be seen. Engage the gears while aligning the mark of the gear (BU1) with the protruding part of the rotary encoder.

protruding part

mark

6

HCD-NXM4D

1-8. GEAR (BU1)




3 pulley (BU)

5 gear (BU2)

7 gear (BU1)

1 belt (sub tray)

gear (BU1)

cam (BU)

PRECAUTION DURING GEAR (BU1) INSTALLATION

Before re-assembling, slide the cam (BU) in the direction of the arrow. Assemble the gear (BU1) in such a manner that the grooveof the cam (BU) is aligned with the rib of the gear (BU1).

rib groove

7

HCD-NXM4D

MEMO

HCD-NXM4D

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.

Ver. Date Description of Revision

1.0 2004.06 New

1.1 2005.03 SUPPLEMENT-1 : CDM81 DISASSEMBLY (SPM-05019)

1.2 2005.05 Part No. change of the Ref. No. 3. (SPM-05029)

Illustration correction of the Ref. No. 53. (SPM-05031)

Part No. change of the Ref. No. 52. (SPM-05032)

Documents

HCD-NXM4D