Upload
lydieu
View
243
Download
0
Embed Size (px)
Citation preview
E3™ SYSTEMHardware, Track, Sill System & Weathersealing for Exterior Folding Doors & Windows
Exterior Folding Door Systems
E3™ Specification & Fabrication Catalogue • Revision (17) March 15, 2018
PRINTED CATALOGUE MAY NOT BE UP TO DATE, ALWAYS REFER TO PRODUCT WEBSITE FOR MOST UP TO DATE CONTENT.
© Copyright 2018 • Eclipse Architectural®2 ALL DRAWINGS NO SCALE
E3 HARDWARE, TRACK, SILL SYSTEM & WEATHERSEALING FOR EXTERIOR FOLDING DOORS & WINDOWS
maximum panel weight: 250lbs (115kg) each panelmaximum panel width: 47-1/4” (1200mm)maximum panel height: 141-47/64” (3600mm)maximum number of panels: 8 each way
In a single direction
Parts Selection
Top Track With flushbolt pin channel
Weatherseals & Astragal
Sill System Floor Channel
Flushbolts or Twinpoint
• panel thickness: 1-3/4” (44.5mm) or 2-1/4” (57mm) when using E3™ sill system• panel thickness: 1-3/8” (34.9mm) to 3” (76.2mm) when using floor channelNOTE: When using maximum panel width & height 47-1/4” (1200mm) x 141-47/64” (3600mm) panel may exceed maximum panel weight of 250 lbs (115 kg). Calculated weight check should be done.
Eclipse E3 is specified with 5 separate groups: track, sill, weathersealing, flushbolts and hardware. Components are required from all 5 groups to build an Eclipse folding door system.
KTE3DJEclipse E3 Drilling JigSee E3 Drilling Jig instruction sheet on www.eclipsearchitectural.com (under Products > E3 folding door systems)
DS434 Weatherseal for sill, jamb and header. Black, brown or white
KT190 Fir astragal, may be stained or painted
DSP108-35BL Pile weatherseal for door with astragal, 5/16” (8mm) pile height, black
DS7145-270BL Pile weatherseal for KT70 & KT75 top track, black
DS434 Kerf seal
DS416 Weatherseal for between doors. Black, brown or white
DS369A7145BL Aluminum T-slot extrusion with black pile insert, for bottom of doors
DS415BL black DS415W white DS415B brown weatherseal for between doors, use on clad doors where kerf slot is not possible
KT75C clear anodizedKT75D bronze anodizedLengths available: 111”, 147”, 183”, 222”, 294” (2.81m, 3.73m, 4.64m, 5.63m, 7.46m)
Top Track, extruded aluminum (OPTIONAL)
KT70D bronze anodized. Lengths available: 111”, 147”, 183”, 222”, 294” (2819mm, 3754mm, 4648mm, 5639mm, 7468mm)
2-7/16” (62mm)
2” (50.2mm)
4 lengths available:
DBOT & DBSY Style 1” (25.4mm) throw length regardless of bolt length. Finishes available: brushed aluminum or bronze powder coat.
KT23DV floor channel, bronze anodized with PVC insert, black.Lengths available: 111”, 147”, 183”, 222”, 294” (2.81m, 3.73m, 4.64m, 5.63m, 7.46m)
KT23BLVE Replacement PVC insert (only)
KT795 8” wide (203mm) for 1-3/4” (44.5mm) door.KT797 8” wide (203mm) for 2-1/4” (57mm) door. KT775 6-9/16” wide (167mm) for 1-3/4” (44.5mm) door. KT777 6-9/16” wide (167mm) for 2-1/4” (57mm) door.
KT749 Flushbolt cup, satin or bronze
KT750GASKET included with KT749, fits under rim of cup
Hardware
2 stock finishes available: Stainless steel & pvd bronze
1-31/32” (50mm)
3-37/64” (90.9mm)
NEWPRODUCT
NEWPRODUCT
7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)
1" (25.4mm)
NEWPRODUCT
KT768GASKET sill to jamb assembly gasket
Fir top water return sill, extruded aluminum clear or bronze anodized.
KT795COVERBLVEPVC insert, black. Snap in cover for flushbolt channels for the new Eclipse sill & top track. Fits into sills above.
PVD brass (TG) finish is custom order, call for manufacturing time.
FOR OUTSWING & INSWING DOORS
Flushbolt cup used with floor channel and ADA sill
Lengths available: 111”, 147”, 183”, 222”, 294” (2819mm, 3754mm, 4648mm, 5639mm, 7468mm). Order flushbolt cups and sill assembly end gaskets separately.
© Copyright 2018 • Eclipse Architectural® 3
INDEXKT190C84B 2, 33KT190C84BL 2, 33KT190C84W 2, 33KT190C96B 2, 33KT190C96BL 2, 33KT190C96W 2, 33KT190C108B 2, 33KT190C108BL 2, 33KT190C108W 2, 33KT190C120B 2, 33KT190C120BL 2, 33KT190C120W 2, 33KT23BLVE 2, 32KT23DV 2, 32KT23D-RADIUS 19, 32DS369A7145BL 2, 8, 9, 10, 11DS416B 2, 5, 9, 12DS416BL 2, 5, 9, 12DS416W 2, 5, 9, 12DS434B 2, 15, 16DS434B81 2, 15, 16DS434B96 2, 15, 16DS434BL 2, 15, 16DS434BL81 2, 15, 16DS434BL96 2, 15, 16DS434W 2, 15, 16DS434W81 2, 15, 16DS434W96 2, 15, 16DS415B96 2DS415B144 2DS415W96 2DS415W144 2DS415BL144 2KT769D 21KT779D 20KT70D 17KT70D-RADIUS 17KT75C 2, 14, 15, 16KT75D 2, 14, 15, 16KT749BRONZE 2, 23, 24KT749DCH 2, 23, 24KT750SPC 2, 8, 10KT760SPC 10, 11, 16KT770SPC 9, 11KT780SPC 8, 9KT752E3FIRD 16KT788E3D 16KT841REDUCER 9, 11KTDBSY 24KTDBOC200NRTG 22KTDBOC200NRQ 22KTDBOC200NRX 22KTDBOC400NRTG 22KTDBOC400NRQ 22
KTDBOC400NRX 22KTDBOE200NRTG 22KTDBOE200NRQ 22KTDBOE200NRX 22KTDBOE400NRTG 22KTDBOE400NRQ 22KTDBOE400NRX 22KTDBOE600NRTG 22KTDBOE600NRQ 22KTDBOE600NRX 22KTDBOE1000NRTG 22KTDBOE1000NRQ 22KTDBOE1000NRX 22KTDBOT200NRTG 23KTDBOT200NRQ 23KTDBOT200NRX 23KTDBOT400NRTG 23KTDBOT400NRQ 23KTDBOT400NRX 23KTDBOT600NRTG 23KTDBOT600NRQ 23KTDBOT600NRX 23KTDBOT1000NRTG 23KTDBOT1000NRQ 23KTDBOT1000NRX 23KTE3CICSTG 36, 37KTE3CICSOL 36, 37KTE3CICSS 36, 37KTE3CLCSTG 36, 37KTE3CLCSOL 36, 37KTE3CLCSS 36, 37KTE3CPSTG 36, 37KTE3CPSOL 36, 37KTE3CPSS 36, 37KTE3CRCSTG 36, 37KTE3CRCSOL 36, 37KTE3CRCSS 36, 37KTE3EHTG 36, 37KTE3EHOL 36, 37KTE3EHS 36, 37KTE3HTG 36, 37KTE3HOL 36, 37KTE3HS 36, 37KTE3HHTG 36, 37KTE3HHOL 36, 37KTE3HHS 36, 37KTE3HHNHTG 36, 37KTE3HHNHOL 36, 37KTE3HHNHS 36, 37KTE3HNHTG 36, 37KTE3HNHOL 36, 37KTE3HNHS 36, 37KTE3HHNHSTG 36, 37KTE3HHNHSOL 36, 37
KTE3HHNHSS 36, 37KTE3HHTG 36, 37KTE3HHSOL 36, 37KTE3HHSS 36, 37KTE3HNHSTG 36, 37KTE3HNHSOL 36, 37KTE3HNHSS 36, 37KTE3HSTG 36, 37KTE3HSOL 36, 37KTE3HSS 36, 37KTE3WPSTG 36, 37KTE3WPSOL 36, 37KTE3WPSS 36, 37DSP108-35BL 2, 5, 12, 13DS7145-270BL 14,20, 21, 22
Misc / Spare & Replacement PartsKT750GASKET 2KT768GASKET 2, 32KTDBPCS 22KTDBSPQ 22, 23, 24KTDBSPS 22, 23, 24KTE2DBFORB 22, 23, 24KTE3CBPIVOTH 36KTE3DJ 2KTE3HGASKET 4KTE3SCREWTG 37KTE3SCREWOL 37KTE3SCREWSS 37KTE3WPCUPQ 36KTE3WPCUPS 36KTEMAG 35KTDBSPOCX or Q 22KT740DHC 33KT740DHD 33KT745ESPX 5, 7KT745ESPQ 5, 7KTDCAS 34KTDCAOL 34
TwinpointECLT2TRSN0924 27, 28,29,30ECLT2TRSN0930 27, 28,29,30ECLT2NS 27ECDF3SHN 27ECDF4SHNS 27ECLTBC8S 27, 30ECLT2RB 27, 29ECLTSP8SS 27, 30ECLTSP8OL 27, 30
LegendX Satin aluminumTG PVD brass (custom order)OL PVD bronzeQ Powder coat bronzeSS Stainless steelC Clear anodizedD Bronze anodizedB BrownBVE Black vinyl extrusionBL BlackDHC Satin / clearDHD Bronze anodizedDHBL Black powder coatDHW White powder coatBL Black pile
SwingIS InswingOS Outswing
MiscSPC Sill protective coverGASKET A/B gasketFORB Router bitFIR Fir top mouldDJ Drill jig for hinges
Lengths For Flushbolts7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)
HardwareICS Intermediate carrier 3 piece setLCS Left carrier 2 piece setRCS Right corner 2 piece setPS Pivot top & bottom 2 piece setEH “D” pull handle 1 pieceH Hinge flat with handle 1 pieceHH Hinge offset with handle 1 pieceHNH Hinge flat no handle 1 pieceHHNH Hinge offset no handle 1 pieceHS Hinge flat with handle 3 piece set HHS Hinge offset with handle 3 piece setHNHS Hinge flat no handle 3 piece setHHNHS Hinge offset no handle 3 piece setWP Wall pivot
Misc / Spare Hardware ComponentsPCS End cap for OC flushbolts pinSP Striker plateCBP Bottom pivot housingPCP Pivot capSCREW Screws for hinge flapsSPOC Striker plate OC flushboltTPPLATE Top pivot mounting plateDH Door hold
Flushbolts
KTDBOT For outswing applicationKTDBOC For inswing application installed at
bottom of panelsKTDBOE For inswing application installed at top
of panelsKTDBSY For outswing application
© Copyright 2018 • Eclipse Architectural®4 ALL DRAWINGS NO SCALE
2-7/16” (62mm)
2” (50.2mm)
neopreneblackgasket
1-17/32” (39mm)to face of door
5/16” (8mm)from center of
top track to face of door
centre of track tocentre of channel23/32” (18.5mm)
3/8” (9.5mm) panelclearance to sill
7/8” (22mm)
15/16”(24mm)
19/32” (15mm)
3/16” (5mm)panel clearance
to head
EXTERIOR INTERIOR
KTE3HGASKETAdhesive blackgasket for optimum sealing performance around all hinge flaps.
2-3/8” (60mm) bottom of door to bottom of hinge flap when using flush bolts.
5-29/32” (150mm) when using twinpoint lock.
top of doorto top of hinge
flap 19/32” (15mm)
2-3/8” (60mm) top of door to top of hinge flap when using flush bolts.
5-29/32” (150mm) when using twinpoint lock.
E3™ ARCHITECTURAL DETAIL
R.O.
panel width
panel thickness
half offsethinges
outswingpanels
5/8” (16mm)
4 one way configuration
19/32” (15mm)hinge offset
panel offset19/32” (15mm)
5-1/2” (139.7mm)
1-5/16” (33.5mm)
Centre of top track to centre of bottom channel 23/32” (18.5mm)
EXTERIOR INTERIOR
KT795 sill
KT75 top track
KT70 top track
© Copyright 2018 • Eclipse Architectural® 5ALL DRAWINGS NO SCALE
E3™ ARCHITECTURAL DETAIL
9/32” (7mm) jamb clearance 5/32” (4mm) panel to panel gap
5/32” (4mm) panel to panel gap11/16” (17.5mm) jamb thickness
5/32” (4mm) panel to panel gap
9/32” (7mm) jamb clearance
Outswing Application
DS416 & DSP108-35BL Weatherseal Detail for 1-3/4” (44.5mm) Door
flushbolt machiningcentered at stile width
RO.5 (R1/64)
pivot doorweathersealapplication
11/16”(17.5mm)
11/16”(17.5mm)
1/8”(3.2mm)
3/8”(9.5mm)
1/8” (2.5mm) 9/16” (14mm)
5/32” (4mm)
DSP10835BL
DS416
3/8”(9.5mm)
1/8”(3.5mm)
6-9/16”(166.7mm)
5/16”(7.4mm)
9/32”(7mm)
3/4” (18.5mm)
5/16” (7.4mm)5/16” (7.4mm)
5/16”(7.4mm)
1/8” (2.8mm)
1-3/4”(44.5mm)
1-7/16” (36mm)9/16” (14mm)
4-3/8”(110.6mm)
39/64”(15.4mm)
1-5/8”(41mm)
CL
CL
CLREF
REF
latching door to jamb, weatherseal & strike plate application for 3L, 3R, 5L, 5R, 7L or 7R.
KT745extended strike plate for 1-3/4” (44.45mm) door thickness only. Used with standard style lock set.
DS434
4-5/16”(107mm)
top pivot
wall pivot
bottom pivot
jamb or pivot door basic door basic door leading door
bottom guide
right hand carrierintermediate
carrier sethinge setfacing inside
hingesetfacinginside
EXTERIOR
INTERIOR
9/32
” (7m
m)
jamb
clear
ance
9/32
” (7m
m)
jamb
clear
ance
4L (4 doors folding left) Exterior View (all doors are same width)
NOTE: when using 2-1/4” (57mm) panel thickness on 2L2R and 4L4R configurations, the gapping between the 2 meeting panels should be 1/2” (12.7mm). Hinge flaps on the meeting stiles should be machined into the edge of the door.
4-5/16”(110mm)
4”(107mm)
Extended Strike Plate for 1-3/4” Door Only.Used with standardstyle lock set.
KT745ESPXSatin finish
KT745ESPQBronze powder coat
LHDSSPLK73160LH
Used only with MultiPoint lock setExtended Jamb Strike
RHDSSPLK73260RH
© Copyright 2018 • Eclipse Architectural®6 ALL DRAWINGS NO SCALE
2L
2L1R
3L
3L1R
4L
4L1R
3L2R
5L
3L3R
7L
4L3R
5L2R
5L3R
6L
1x KTE3CPS pivot set1x KTE3CRCS right carrier set1x KTE3HS hinge set2x KTDB non-keyed flushbolt
RCS
HS
PSWPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPS
WPSPS PS
PS
PS PS
PS
PSPS
PS PS
PS
PS PS
PS PS
PS
PS
PS
PS
HS
HHS
HHS
HHS HHS
HHS HHS
HHS HS
HS
HS
HS
HS
HHS
HHS
HHS HHS
HHS
HHS
RCS
ICS
ICS
ICS
ICS
ICS
ICS ICS
ICS ICS
ICS
HHS
ICS
ICS ICS
ICS
HHS
ICSICS
RCS
RCS
LCS
LCS
RCS
2x KTE3CPS pivot set1x KTE3CRCS right carrier set1x KTE3HS hinge set2x KTDB non-keyed flushbolt
1x KTE3CPS pivot set1x KTE3CICS intermediate carrier set1x KTE3HHS half offset hinge set2x KTDB non-keyed flushbolt
2x KTE3CPS pivot set1x KTE3CICS intermediate carrier set1x KTE3HHS half offset hinge set4x KTDB non-keyed flushbolt
1x KTE3CPS pivot set1x KTE3CICS intermediate carrier set1x KTE3CRCS right carrier set2x KTE3HHS half offset hinge set4x KTDB non-keyed flushbolt
2x KTE3CPS pivot set1x KTE3CICS intermediate carrier set1x KTE3CRCS right carrier set2x KTE3HHS half offset hinge set4x KTDB non-keyed flushbolt
2x KTE3CPS pivot set1x KTE3CICS intermediate carrier set1x KTE3CLCS left carrier set1x KTE3HS hinge set1x KTE3HHS half offset hinge set4x KTDB non-keyed flushbolt
1x KTE3CPS pivot set2x KTE3CICS intermediate carrier set1x KTE3HS hinge set1x KTE3HHS half offset hinge set4x KTDBnon-keyed flushbolt
2x KTE3CPS pivot set2x KTE3CICS intermediate carrier set2x KTE3HHS half offset hinge set6x KTDB non-keyed flushbolt
2x KTE3CPS pivot set2x KTE3CICS intermediate carrier set1x KTE3CRCS right carrier set3x KTE3HHS half offset hinge set6x KTDB non-keyed flushbolt
2x KTE3CPS pivot set2x KTE3CICS intermediate carrier set1x KTE3CLCS left carrier set2x KTE3HS hinge set1x KTE3HHS half offset hinge set6x KTDB non-keyed flushbolt
2x KTE3CPS pivot set3x KTE3CICS intermediate carrier set1x KTE3HS hinge set2x KTE3HHS half offset hinge set8x KTDB non-keyed flushbolt
WPSPS
HS HS
HHS
HHS
ICS ICS ICS 1x KTE3CPS pivot set3x KTE3CICS intermediate carrier set2x KTE3HS hinge set1x KTE3HHS half offset hinge set6x KTDB non-keyed flushbolt
FB
WPSPS
HHS
ICS ICS RCS 1x KTE3CPS pivot set2x KTE3CICS intermediate carrier set1x KTE3CRCS right carrier set1x KTE3HS hinge set2xKTE3HHS half offset hinge set6x KTDB non-keyed flushbolt
DH
ESP
DH
DH
DH
ESP
DH DH
DH
ESP
DH
DH
DH DH
DH
HS HHS
FB
FB
FB
FB FB
FB FB
FB FB
FB FB
FB FB FB
FB FB FB
FB FB FB
FB FB FB
FB FB FB
FB FB
1x KTE3WPS middle wall pivot
2x KTE3WPS middle wall pivot
1x KTE3WPS middle wall pivot
2x KTE3WPS middle wall pivot
1x KTE3WPS middle wall pivot
2x KTE3WPS middle wall pivot
2x KTE3WPS middle wall pivot
1x KTE3WPS middle wall pivot
2x KTE3WPS middle wall pivot
1x KTE3WPS middle wall pivot
2x KTE3WPS middle wall pivot
2x KTE3WPS middle wall pivot
2x KTE3WPS middle wall pivot
1x KTE3WPS middle wall pivot
FB
FB
FB
FB
Passage Set Lock by Other
Flushbolts Top & Bottom
Twinpoint Option to FB
Astragal
Door Hold
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
LEGEND
4-5/16”
4”
Extended strike plate for 1-3/4” door only
KT745ESPXSatin finish
KT745ESPQBronze powder coat
this configurationnot accessible from exterior
this configurationnot accessible from exterior
this configurationnot accessible from exterior
1x KTE3CLCSleft carrier setPer pair of doors:
1x KTE3CRCSright carrier set1x KTE3HShinge set2x KTDBnon-keyed flushbolt
Hardware LegendPS Pivot setWPS Wall pivot setICS Intermediate carrier setLCS Left carrier setRCS Right carrier setHHS Half offset hinge setHS Hinge set (flat)FB FlushboltESP Extended strike plateDH Door holdMAG MagnetTP Twinpoint
Floating Door PairsINTERIOR
EXTERIOR
may be reversed
HARDWARE LIST FOR DOOR CONFIGURATIONS Passage Set/Lock, Flushbolt, Astragal & Hardware Placement For Outswing ApplicationsFrom Left To Right
Configuration is always determined when viewing system from exterior side, going from left to right.
Use “D” pull handle on exit door (outswing system) where passage set / lock not required. Use flushbolts top and bottom to lock door from the inside only. NOTE: exit door not accessible from exterior.
INTERIOR
EXTERIOR
OUTSWING
INSWING
INTERIOR
EXTERIOR
3L
3LI
How To Determine Swing Of Systems
FB FB3L INTERIOR
EXTERIOR
outswing application “D” pull handle option
Use one “D” pull handle on each pair of inswing doors to pull open and close doors.Inswing application “D” pull handle option
FB FB5RI
INTERIOR
EXTERIOR
© Copyright 2018 • Eclipse Architectural® 7ALL DRAWINGS NO SCALE
1x KTE3CPSpivot set2x KTE3CICSintermediate carrier set1x KTE3HShinge set1x KTE3HHShalf offset hinge set4x KTDBnon-keyed flushbolt
2x KTE3CPSpivot set2x KTE3CICSintermediate carrier set1x KTE3CLCSleft carrier set3x KTE3HHShalf offset hinge set6x KTDBnon-keyed flushbolt
1x KTE3CPSpivot set3x KTE3CICSintermediate carrier set2x KTE3HShinge set1x KTE3HHShalf offset hinge set6x KTDBnon-keyed flushbolt
2x KTE3CPSpivot set2x KTE3CICSintermediate carrier set1x KTE3CRCSright carrier set2x KTE3HShinge set1x KTE3HHShalf offset hinge set6x KTDBnon-keyed flushbolt
1x KTE3CPSpivot set3x KTE3CICSintermediate carrier set1x KTE3CLCSleft carrier set2x KTE3HShinge set2x KTE3HHShalf offset hinge set8x KTDBnon-keyed flushbolt
1x KTE3CPSpivot set1x KTE3CLCSleft carrier set1x KTE3HShinge set2x KTDBnon-keyed flushbolt
2x KTE3CPSpivot set1x KTE3CLCSleft carrier set1x KTE3HShinge set2x KTDBnon-keyed flushbolt
1x KTE3CPSpivot set1x KTE3CICSintermediate carrier set1x KTE3HHShalf offset hinge set2x KTDBnon-keyed flushbolt
2x KTE3CPSpivot set1x KTE3CICSintermediate carrier set1x KTE3HHShalf offset hinge set4x KTDBnon-keyed flushbolt
2x KTE3CPSpivot set1x KTE3CLCSleft carrier set1x KTE3CRCSright carrier set2x KTE3HShinge set4x KTDBnon-keyed flushbolt
2x KTE3CPSpivot set1x KTE3CICSintermediate carrier set1x KTE3CLCSleft carrier set2x KTE3HHShalf offset hinge set4x KTDBnon-keyed flushbolt
1x KTE3CPSpivot set1x KTE3CICSintermediate carrier set1x KTE3CLCSleft carrier set2x KTE3HHShalf offset hinge set4x KTDBnon-keyed flushbolt
2x KTE3CPSpivot set1x KTE3CICSintermediate carrier set1x KTE3CRCSright carrier set1x KTE3HShinge set1x KTE3HHShalf offset hinge set4x KTDBnon-keyed flushbolt
RCS
RCS
RCS
LCS
LCS
LCS
LCS
LCS
LCS
LCS
HS
HS
HS
HS
HS
HS
HS
HS
HSHS
HS
PS
PS
PS
PS
PSPS
PS
PSPS
PS
PS PS
PS
PS PS
PS
PS
PS
PS
PS
HHS
HHS
HHS
HHS HHS
HHS
HHS
HHS
HS
HHS
HHS HHS
HHS
HHSHHS
HHS
ICS
ICS
ICS
ICS
ICS
ICS
ICS
ICS ICS
ICS
ICS ICS ICS
ICS
ICS
ICS
ICS
WPS
WPS
WPSWPS
WPS
WPS
WPS
WPS
WPS
WPSWPS
WPS
WPS
WPS
WPS WPS
WPS
WPS
WPS
WPS
DHESP
DH
DHESP
DH
DH
DH
DH
FB
FB
FB
FBFB
FB FB
FB FB
FB FB
FB FB
FB FB
FB FBFB
FB FBFB
FB FBFB
FB FBFB FB
1x KTE3WPSmiddle wall pivot
2x KTE3WPSmiddle wall pivot
1x KTE3WPSmiddle wall pivot
2x KTE3WPSmiddle wall pivot
2x KTE3WPSmiddle wall pivot
2x KTE3WPSmiddle wall pivot
1x KTE3WPSmiddle wall pivot
2x KTE3WPSmiddle wall pivot
1x KTE3WPSmiddle wall pivot
2x KTE3WPSmiddle wall pivot
1x KTE3WPSmiddle wall pivot
2x KTE3WPSmiddle wall pivot
1x KTE3WPSmiddle wall pivot
Hardware LegendPS Pivot setWPS Wall pivot setICS Intermediate carrier setLCS Left carrier setRCS Right carrier setHHS Half offset hinge setHS Hinge set (flat)FB FlushboltESP Extended strike plateDH Door holdMAG MagnetTP Twinpoint
FB
DH
Passage Set Lock by Other
Flushbolts Top & Bottom
Twinpoint Option to FB
Astragal
Door Hold
Legend
Extended Strike Plate for 1-3/4” Door Only.Used with standardstyle lock set.
KT745ESPXSatin finish
KT745ESPQBronze powder coat
panel width
panel thickness
half offsethinges
outswingpanels
5/8” (16mm)
4 one way configuration
19/32” (15mm)hinge offset
pane
l offs
et19
/32”
(15m
m)
This configuration not accessible from exterior
This configuration not accessible from exterior
This configuration not accessible from exterior
This configuration not accessible from exterior
1L2R
3R
1L3R
2L2R
1L4R
4R
2L3R
5R
3L4R
7R
2L5R
8R
2R
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
may be reversed
LHDSSPLK73160LH
Used only with MultiPoint lock set
Extended Jamb Strike
RHDSSPLK73260RH
4-5/16”
4”
HARDWARE LIST FOR DOOR CONFIGURATIONS Passage Set/Lock, Flushbolt, Astragal & Hardware Placement For Outswing ApplicationsFrom Left To Right
intermediate carrier & guide set left carrier & guide setINTERIOR
EXTERIOR
pivot set
flushbolts flushbolts
half offset hinge set flat hinge setpassage set
pivot set
jamb doorjamb doorbasic door
leading door
service door
door hold
Hardware Application 3L2R
© Copyright 2018 • Eclipse Architectural®FULL SCALE EXCEPT AS NOTED8
19/3
2”
(15m
m)
viny
l cha
nnel
inse
rt1-
3/16
”(3
0mm
)
wee
p ho
le
wee
p ho
les
2-5/
32”
(54m
m)
1-23
/32”
(44m
m)
FIR
OR O
AK
TOP
WOO
D SU
BSTR
ATE
13/3
2” (1
0mm
)
6-9/
16”
(166
.7m
m)
jam
b lin
e
8” (2
03m
m)
1/4”
(6m
m)E3
bot
tom
hi
nge
& g
uide
6-9/
16”
(166
.7m
m)
jam
b lin
e
KT795COVERBLVE
PVC
inse
rt, b
lack
2-1
/4”
(57m
m)
KT797S
ill
3/8”
(9
.5m
m)
DS434
Kerf
seal
DS369A7145BL
Alum
inum
T-s
lot
extru
sion
with
gra
ypi
le in
sert
cent
re o
f top
trac
k to
cen
tre o
f bo
ttom
cha
nnel
=
23/3
2” (1
8.5m
m)
ECLIPSE, KT797 (8") OUTSWING SILL SYSTEM FOR 2-1/4" (57MM) DOOR THICKNESS
New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural.Extrusion Alloy 6063 T5. Actual Full Sill Width: 8" (203mm) Channel Sill for Flushbolt or Twinpoint.
KT797E3FIRC Clear anodizedKT797E3FIRD Bronze anodized
KT7
80
SP
CPr
otec
tive
vinyl
sill c
over
for s
ill no
se
KT7
50
SP
CPr
otec
tive
vinyl
sill c
over
for i
nter
ior f
ir to
p
EXTE
RIOR
DBOT
Flu
shbo
lt
Two
lock
ing
optio
ns: Tw
inpo
int
© Copyright 2018 • Eclipse Architectural® FULL SCALE EXCEPT AS NOTED 9
ECLIPSE KT795 (8”) OUTSWING SILL SYSTEM FOR 1-3/4” (44.5MM) DOOR THICKNESS
New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural.
Extrusion Alloy 6063 T5. Actual Full Sill Width: 8” (203mm) Channel Sill for Flushbolt or Twinpoint.
19/3
2”
(15m
m)
viny
l cha
nnel
inse
rt1-
3/16
”(3
0mm
)
wee
p ho
le
wee
p ho
les
2-5/
32”
(54m
m)
2-7/
32”
(57m
m)
WOO
D SU
BSTR
ATE
3/8”
(9
.5m
m)
1-3
/4”
(44.
5mm
)
13/3
2” (1
0mm
)
8” (2
03m
m)
1/4”
(6m
m)E3
bot
tom
hi
nge
& g
uide
6-9/
16”
(166
.7m
m)
jam
b lin
e
DS434
Kerf
seal
KT841
Redu
cer
KT795S
ill
KT795COVERBLVE
PVC
inse
rt, b
lack
6-9/
16”
(166
.7m
m)
jam
b lin
e
cent
re o
f top
trac
k to
cen
tre o
f bo
ttom
cha
nnel
=
23/3
2” (1
8.5m
m)
DS369A7145BL
Alum
inum
T-s
lot
extru
sion
with
gra
ypi
le in
sert
FIR
OR O
AK
TOP
KT795E3FIRC Clear anodizedKT795E3FIRD Bronze anodized
KT7
80
SP
CPr
otec
tive
vinyl
sill c
over
for s
ill no
seK
T77
0S
PC
Prot
ectiv
e vin
yl sil
l cov
er fo
r int
erio
r fir
top
EXTE
RIOR
DBOT
Flu
shbo
lt
Two
lock
ing
optio
ns: Tw
inpo
int
© Copyright 2018 • Eclipse Architectural®FULL SCALE EXCEPT AS NOTED10
1-3/
16”
(30m
m)
6-9/
16”
(167
mm
)
6-9/
16”
(166
.7m
m)
jam
b lin
e
19/3
2”
(15m
m)
13/3
2”(1
0mm
)1/
4” (6
mm
)
viny
l cha
nnel
inse
rt
wee
p ho
les
wee
p ho
le
2-1
/4”
(57m
m)
1-23
/32”
(44m
m)
2-5/
32”
(54m
m)
WOO
D SU
BSTR
ATE
KT777S
ill
3/8”
(9
.5m
m)
DS434
Kerf
seal
KT795COVERBLVE
PVC
inse
rt, b
lack
6-9/
16”
(166
.7m
m)
jam
b lin
e
E3 b
otto
m
hing
e &
gui
de
cent
re o
f top
trac
k to
cen
tre o
f bo
ttom
cha
nnel
=
23/3
2” (1
8.5m
m)
DS369A7145BL
Alum
inum
T-s
lot
extru
sion
with
gra
ypi
le in
sert
FIR
OR O
AK
TOP
New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural.
Extrusion Alloy 6063 T5. Actual Full Sill Width: 6-9/16” (166.7mm) Channel Sill for Flushbolt or Twinpoint.
ECLIPSE KT777 (6-9/16”) OUTSWING SILL SYSTEM FOR 2-1/4” (57MM) DOOR THICKNESS
KT777E3FIRC Clear anodizedKT777E3FIRD Bronze anodized
KT7
50
SP
CPr
otec
tive
vinyl
sill c
over
for i
nter
ior f
ir to
pK
T76
0S
PC
Prot
ectiv
e vin
yl sil
l cov
er fo
r sill
nose
EXTE
RIOR
DBOT
Flu
shbo
lt
Two
lock
ing
optio
ns: Tw
inpo
int
© Copyright 2018 • Eclipse Architectural® FULL SCALE EXCEPT AS NOTED 11
1-3/
16”
(30m
m)
6-9/
16”
(167
mm
)
6-9/
16”
(166
.7m
m)
jam
b lin
e
19/3
2”
(15m
m)
13/3
2” (1
0mm
)1/
4” (6
mm
)
viny
l cha
nnel
inse
rt
wee
p ho
les
2-5/
32”
(54m
m)
WOO
D SU
BSTR
ATE
1-3
/4”
(44.
5mm
)
2-7/
32”
(57m
m)
KT775S
ill
KT841
Redu
cer
3/8”
(9
.5m
m)
DS434
Kerf
seal
KT795COVERBLVE
PVC
inse
rt, b
lack
6-9/
16”
(166
.7m
m)
jam
b lin
e
wee
p ho
le
E3 b
otto
m
hing
e &
gui
de
cent
re o
f top
trac
k to
cen
tre o
f bo
ttom
cha
nnel
=
23/3
2” (1
8.5m
m)
DS369A7145BL
Alum
inum
T-s
lot
extru
sion
with
gra
ypi
le in
sert
FIR
OR O
AK
TOP
New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural.
Extrusion Alloy 6063 T5. Actual Full Sill Width: 6-9/16” (166.7mm) Channel Sill for Flushbolt or Twinpoint.
ECLIPSE KT775 (6-9/16”) OUTSWING SILL SYSTEM FOR 1-3/4” (44.5MM) DOOR THICKNESS
KT775E3FIRC Clear anodizedKT775E3FIRD Bronze anodized
KT7
70
SP
CPr
otec
tive
vinyl
sill c
over
for i
nter
ior f
ir to
pK
T76
0S
PC
Prot
ectiv
e vin
yl sil
l cov
er fo
r sill
nose
EXTE
RIOR
DBOT
Flu
shbo
lt
Two
lock
ing
optio
ns: Tw
inpo
int
© Copyright 2018 • Eclipse Architectural®FULL SCALE EXCEPT AS NOTED12
5/16
”(8
mm
)
19/6
4”(7
.5m
m)
11/1
6”(1
7.5m
m)
1/8”
(3m
m)
1/8”
(3m
m)
11/1
6”(1
7.5m
m)
9/16
”(1
5mm
)
1-3/
32”
(28m
m)
3/8”
(9.5
mm
)
4-27
/32”
(123
mm
)
6-9/
16”
(167
mm
)
CL
9/32
”(7
mm
)
7/64
”(2
.5m
m)
7/64
” (2
.8m
m)
DS416ke
rf se
al in
sert
9/16
”(1
4mm
)
1-7/
16”
(36m
m)
Flus
hbol
t mac
hini
ng d
epth
:1)
KTDBSY9
/16”
(14m
m)
2) KTDBOC
43/6
4” (1
7mm
)3)
KTDBOE4
3/64
” (1
7mm
)4)
KTDBOT3
/4”
(19m
m)
5/16
” (8
mm
)
2-1/
4”(5
7mm
)
DS43
4ke
rf se
alin
sert
R =
1/64
” (0
.5m
m)
Drop
bolt
mac
hini
ng
cent
ered
at s
tile
wid
th w
ith
dedi
cate
d ro
uter
bits
.
NOSCALE
9/32
”(7
mm
)
Mul
tipoi
ntla
tch
Mul
tipoi
ntfa
ce p
late
notc
hre
quire
din
jam
b
DSP10835BL
pile
wea
ther
sesa
l
5/32
”(4
mm
)
DS43
4ke
rf se
alin
sert
REF
EXTERIOR
LH DSSPLK73160LH
Used
onl
y w
ithM
ultiP
oint
lo
ck s
et
NOSCALE
Exte
nded
Jam
b St
rike
RHDSSPLK73260RH
E3™ JAMB FOR 2-1/4” (57MM) DOOR THICKNESSExterior E3 Folding Door, Outswing Application
Actual machining for flushbolts (face plate)1-27/64” x 7-7/8” (36mm x 200mm)1-27/64” x 15-3/4” (36mm x 400mm)1-27/64” x 23-5/8” (36mm x 600mm)1-27/64” x 39-3/8” (36mm x 1000mm)
DBOT FlushboltTwo locking options:
TwinpointKT
E2DB
FORB
Flus
hbol
t ro
uter
bit
is av
ailab
le
© Copyright 2018 • Eclipse Architectural® FULL SCALE EXCEPT AS NOTED 13
11/1
6”(1
7.5m
m)
1/8”
(3m
m)
1/8”
(3m
m)
11/1
6”(1
7.5m
m)
9/16
”(1
5mm
)
1-5/
8”(4
1mm
)
3/8”
(9.5
mm
)
4-3/
8”(1
10.6
mm
)
6-9/
16”
(167
mm
)
DS434
kerf
seal
inse
rt
CL
CL
CL
REF
EXTERIOR
9/32
”(7
mm
)
9/32
”(7
mm
)
Drop
bolt
mac
hini
ng
cent
ered
at s
tile
wid
th
with
ded
icat
ed ro
uter
bits
. 7/64
”(2
.5m
m)
R =
1/64
” (0
.5m
m)
7/64
” (2
.8m
m)DS416
kerf
seal
inse
rt
9/16
”(1
4mm
)
1-7/
16”
(36m
m)
23/3
2” (1
8.5m
m)
Flus
hbol
t mac
hini
ng d
epth
:1)
KTDBSY9
/16”
(14m
m)
2) KTDBOC
43/6
4” (1
7mm
)3)
KTDBOE4
3/64
” (1
7mm
)4)
KTDBOT3
/4”
(19m
m)
5/16
” (8
mm
)
5/16
”(8
mm
)
19/6
4”(7
.5m
m)
1-3/
4”(4
4.5m
m)
notc
hre
quire
din
jam
b
5/32
”(4
mm
)
DS434
kerf
seal
inse
rt DSP10835BL
pile
wea
ther
sesa
l
Mul
tipoi
ntla
tch
Mul
tipoi
ntfa
ce p
late
LH DSSPLK73160LH
Used
onl
y w
ithM
ultiP
oint
lo
ck s
et
NO
SCA
LE
Exte
nded
Jam
b St
rike
RHDSSPLK73260RH
NO
SCA
LE
4-5/
16”
(110
mm
)
4”(1
07m
m)Ex
tend
ed S
trik
e Pl
ate
KT745ESPX
Satin
fini
shKT745ESPQ
Bron
ze p
owde
r coa
t
for 1
-3/4
” do
or o
nly.
Used
with
sta
ndar
dst
yle
lock
set
.NOSCALE
E3™ JAMB FOR 1-3/4” (44.5MM) DOOR THICKNESSExterior E3 Folding Door, Outswing Application.
Actual machining for flushbolts (face plate)1-27/64” x 7-7/8” (36mm x 200mm)1-27/64” x 15-3/4” (36mm x 400mm)1-27/64” x 23-5/8” (36mm x 600mm)1-27/64” x 39-3/8” (36mm x 1000mm)
DBOT FlushboltTwo locking options:
Twinpoint
KTE2
DBFO
RB Fl
ushb
olt
rout
er b
it is
avail
able
© Copyright 2018 • Eclipse Architectural®FULL SCALE EXCEPT AS NOTED14
KT75 TOP TRACK FOR 2-1/4” (57MM) DOOR THICKNESS E3™ HEADERExterior E3 Folding Door, KT75 Outswing Application Only. Channel Top Track for Flushbolt or Twinpoint.
New Generation Top Track with Flushbolt Pin Channel.
6-9/
16”
(167
mm
)
5-7/
8” (1
50m
m)
11/1
6”
(17m
m)
2-21
/32”
(6
8mm
)
3/16
” (5
mm
)
19/3
2”
(15m
m)
E3 b
otto
m
hing
e &
gui
de
6-9/
16”
(166
.7m
m)
jam
b lin
e
11/1
6”
(18m
m)
1-31
/32”
(5
0mm
)
11/3
2”
(9m
m)
1/8”
(3m
m)
3/16
” (5
mm
)11
/16”
(18m
m)
19/3
2”
(15m
m)
6-9/
16”
(166
.7m
m)
jam
b lin
e
3/8”
(9.5
mm
)
19/3
2”
(15m
m)
1-1/
8” (2
8mm
)
DS434
Kerf
seal
KT795COVERBLVE
PVC
inse
rt, b
lack
DS7145270BL
Pile
wea
ther
seal
, bla
ck
KT75C ClearKT75D Bronze anodized
EXTE
RIOR
DBOT
Flu
shbo
ltTw
o lo
ckin
g op
tions
:Tw
inpo
int
© Copyright 2018 • Eclipse Architectural® FULL SCALE EXCEPT AS NOTED 15
KT75 TOP TRACK FOR 1-3/4” (44.5MM) DOOR THICKNESS E3™ HEADERExterior E3 Folding Door, KT75 Outswing Application Only. Channel Top Track for Flushbolt or Twinpoint.
New Generation Top Track with Flushbolt Pin Channel.
6-9/
16”
(167
mm
)
5-7/
8” (1
50m
m)
11/1
6”
(18m
m)
1-31
/32”
(5
0mm
)
1/8”
(3m
m)
1/8”
(3m
m)
3/8”
(9.5
mm
)11/3
2” (9
mm
)
1-5/
8” (4
1mm
)
3/16
” (5
mm
)11
/16”
(18m
m)
11/3
2”
(9m
m)
11/1
6”
(17m
m)
2-21
/32”
(6
8mm
)
3/16
” (5
mm
)
19/3
2”
(15m
m)
6-9/
16”
(166
.7m
m)
jam
b lin
e
19/3
2”(1
5mm
)
6-9/
16”
(166
.7m
m)
jam
b lin
e
E3 b
otto
m
hing
e &
gui
de
DS
434
Kerf
seal
KT7
95C
OV
ERB
LVE
PVC
inse
rt, b
lack
DS
7145
-270
BL
Pile
wea
ther
seal
, bl
ack
KT75C Clear anodizedKT75D Bronze anodized
EXTE
RIOR
DBOT
Flu
shbo
ltTw
o lo
ckin
g op
tions
:Tw
inpo
int
© Copyright 2018 • Eclipse Architectural®FULL SCALE EXCEPT AS NOTED16
KT752 SERIES E3™ 5-1/2” (139.7MM) OUTSWING SILL SYSTEMONLY FOR 1-3/4” (44.5mm) Door Thickness & 4-9/16” (115.8 mm) Wall Thickness
NOTE: Door height plus 4-1/4”: (107.9mm) = R.O. (from finished floor line to R.O. header) when using Eclipse frame specs.
2-1/8” (54mm)
INTERIOR
substrate
1-3/16” (30mm)
interior fir topmouldDS434sill weatherseal
white, brown or black
5-1/2” (140 mm)
KT752E3 aluminum sill, clear or bronze anodized
EXTERIOR
weep hole
weep holes
bottom rollerguide channel
vinyl channel insert
channel for flushbolt pin
1-1/16”(27mm)
KT788 E3 ADA LOWRISE ALUMINUM SILL FOR INSWING & OUTSWING DOORS
KT788E3D Bronze anodized only
KT752E3FIRD Outswing sill with fir top, bronze anodized
ADA Compliant
KT760SPCProtective vinyl sill cover for sill nose
BRONZE ANODIZED ONLY
EXTERIOR
NO SCALEUse KTDBSY series flush bolt
23/32”(18.5mm)
6-9/16” (166.7mm)
1/2”(12.7mm)
15/16”(23.6mm)
19/32”(15mm)
1-3/4”(44.45mm)
NO SCALE
drill round hole for pin
no flush bolt cup used
23/32”(18.5mm)
6-9/16” (166.7mm)
1/2”(12.7mm)15/16” (23.6mm)
finished floor line
19/32”(15mm)
KTDBSYFlush bolt
KT749flush bolt cup used,custom drilling required in sill
thermal break
1-3/4” (44.45mm) finished floor line
NO SCALE
Slopes of threshold may be ripped off to achieve flush sill application.
© Copyright 2018 • Eclipse Architectural® 17ALL DRAWINGS NO SCALE
E3™ CORNER UNIT APPLICATION
RADIUS APPLICATION (KT70 TRACK ONLY)
outside corner panel of 1L, 3L, 5L & 7L configurations
Mitre cut sill and head to suit length of openingoutside corner
panel of 4R, 6R & 8R configurations
Apply lock set and/or deadbolt to active door or use flushbolts top & bottom (shown). If using interior flushbolts access from exterior not possible.
door stop
E3 sillINTERIOR VIEW EXTERIOR VIEW
DS416 seal
KT190astragal
4R3L
OUTSIDECORNER
Center point
DOORS
DOORS
KT70D-RADIUS bronze anodized top track (CUSTOM ORDER)*KT23C-RADIUS clear anodized floor channel (CUSTOM ORDER)*KT23D-RADIUS bronze anodized floor channel (CUSTOM ORDER)**CUSTOM ORDER, CALL FOR MANUFACTURING TIME.All supplied as one length only 120” (3048mm)
Minimum Radius14’-7” / 175” (4445mm)to inside face of top track.(Warranty on hardware void if under minimum radius)
RC
X
CP
Arc Length (AL)
R = Radius (length from the C.P. to the edge of the circle)
C = chord lengthX = height of crownCP = center pointAL = arc length
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
© Copyright 2018 • Eclipse Architectural®FULL SCALE EXCEPT AS NOTED18
KT779D E3™ SILL SYSTEM FOR 2-1/4” (57MM) DOOR THICKNESSWater Return All Aluminum Sill System, Thermally Broken For Inswing Folding Doors (Only KT70 Top Track can only be used on inswing application)
10˚ slope
6-9/16” (166.7mm)
2-7/16” (62mm) 11/16”(17.5mm)
11/16”(17.5mm)
2-11/16”(67.7mm)
3/8”(9mm)
2”(50.2mm)
11/16”(17.5mm)
1/4”(6mm)
3/8”(9.5mm) striker plate
Use KTDBOESeries flush bolt
flushbolt pin
KT70E3aluminum top track
DS434kerf seal insert
3/8” (9.5mm)
4-7/8” (123.2mm)
7/16” (10.5mm)
23/32” (18.5mm) center line of top trackto center line of bottom sill channel
2-1/4” (57mm)3-15/16” (99.8mm)
5/16”(8mm)
3/16” (5mm)
1-1/8” (28mm)
DS369
3/8" (9.5mm)
11/16"(18mm)
2-1/16” (53.1mm)
1-11/16” (43.5mm)
7/16"(10.8mm)
3/16”(4mm)
1/4”(7mm)
2-1/8" (54mm)
6-9/16” (166.7mm)I-Strut Thermal break
PVC channel filler
1” (25.7mm)
DS434kerf seal insert
CL CL
1-29/32” (48.4mm)
EXTERIOR INTERIOR
WEEPHOLE
WEEPHOLE
WEEPHOLE
KT779DSill
WEEPHOLE
1/8”(3.17mm)
bronze anodized only
Use KTDBOCSeries flush bolt
KTDBSPOCProtective strike plate
DS7145270BLPile weatherseal, black
BRONZE ANODIZED ONLY
© Copyright 2018 • Eclipse Architectural® FULL SCALE EXCEPT AS NOTED 19
6-9/16” (166.7mm)
2-11/16”(67.7mm)
11/16”(17.5mm)
2”(50.2mm)
3/8”(9mm)
1/4”(6mm)
3/8”(9.5mm)
1/8” (3.17mm)11/16”
(17.5mm)
center lineCLof top track
CLCL
striker plate
flushbolt pin
KT70E3aluminum top track
2-7/16” (62mm) 11/16”(17.5mm)
3/16” (5mm)
1-29/32” (48.4mm)
5/16”(8mm)
4-3/8” (110.6mm)
3/8” (9.5mm)
1-5/8” (40.7mm)
7/16” (10.5mm)3-15/16” (99.8mm)
EXTERIOR INTERIOR
6-9/16” (166.7mm)I-Strut Thermal break
PVC channel filler
1” (25.7mm)KT769DSill
WEEPHOLE
WEEPHOLE
WEEPHOLE
WEEPHOLE
KTDBSPOCProtective strike plate
1/4”(7mm)
3/16”(4mm)
DS369
DS434kerf seal insert
9/16"(14.3mm)
7/16"(10.8mm)
10˚ slope
2-1/8" (54mm)
3/8" (9.5mm)
2-3/8 (56.2mm)
1-3/4” (44.5mm)2-9/16” (65mm)
23/32” (18.5mm) center line of top trackto center line of bottom sill channel
Bronze anodized only
Use KTDBOCSeries flush bolt
Use KTDBOESeries flush bolt
DS7145270BLpile weatherseal, black
DS434kerf seal insert
KT769D E3™ SILL SYSTEM FOR 1-3/4” (44.5MM) DOOR THICKNESSWater Return All Aluminum Sill System, Thermally Broken For Inswing Folding Doors (Only KT70 Top Track can only be used on inswing application)
BRONZE ANODIZED ONLY
© Copyright 2018 • Eclipse Architectural®20 ALL DRAWINGS NO SCALE
bronze powder coat finish over aluminum
KTDBOC200NRQ 8" (200mm) concealed 3/4” FB, throwKTDBOE200NRQ 8" (200mm) 1” throw, round endKTDBOE400NRQ 16" (400mm) 1” throw, round endKTDBOE600NRQ 24" (600mm) 1” throw, round endKTDBOE1000NRQ 39" (1000mm) 1” throw, round end
brushed metallic finish over aluminum to match stainless steel
KTDBOC200NRX 8" (200mm) concealed FB, 3/4” throwKTDBOE200NRX 8" (200mm) 1” throw, round endKTDBOE400NRX 16" (400mm) 1” throw, round endKTDBOE600NRX 24" (600mm) 1” throw, round endKTDBOE1000NRX 39" (1000mm) 1” throw, round end
bright gold finish over aluminum
KTDBOC200NRTG 8" (200mm) concealed FB, 3/4” throwKTDBOE200NRTG 8" (200mm) 1” throw, round endKTDBOE400NRTG 16" (400mm) 1” throw, round endKTDBOE600NRTG 24" (600mm) 1” throw, round endKTDBOE1000NRTG 39" (1000mm) 1” throw, round end
FLUSHBOLTS FOR E3 INSWING FOLDING DOORS: DBOE & DBOC SERIESSPECIFICATIONS Minimum door thickness: 1-3/4” (44.5mm)DBOC Throw length: 3/4” (20mm) • DBOE Throw length: 1” (25mm) Finishes: Bronze powder coat on aluminum to match pvd bronze finish on E3 hinges. Brushed metallic on aluminum to match stainless steel finish on E3 hinges. Bright gold (TG) finish on aluminum to match pvd brass finish on E3 hinges.
Actual machining for flushbolts (face plate)1-27/64” x 7-7/8” (36mm x 200mm)1-27/64” x 15-3/4” (36mm x 400mm)1-27/64” x 23-5/8” (36mm x 600mm)1-27/64” x 39-3/8” (36mm x 1000mm)
PLEASE NOTE: Flushbolt housing & slide bar are manufactured from aluminum components
1-5/16” (33.3mm) face of door to center of pin
1" (25mm)
further machining required for inswing flush bolts offset pins
Flushbolt pin drops into bottom channel or into E3 inswing sill channel.
E3 floor channel
3/4" (20mm)
further machining required for larger bottom pin
KTDBOETop flushbolt
EXTERIOR INTERIOR
1-3/4’’ (45mm) min thickness
KTDBOCBottom flushbolt
KT70Top track
4 lengths available:
KTE2DBFORB Router bit for flushbolts
fit striker to pin side of drop bolt (opposite the black plastic cap)
KTDBPCS Replacement end cap for OC flushbolt pin
Replacement strike plate for OC flushbolt KTDBSPOCX Brushed finishKTDBSPOCQ Bronze powder coat
fit centrally to the drop bolt when in the closed position
Bright gold (TG) finish is custom order, call for manufacturing time.
PRODUCT CODE DESCRIPTION
OC flushbolt for bottom of doors
OE flushbolt for top of doors
Strike plate for headerKTDBSPQ bronze powder coat KTDBSPS Satin chrome
Bright gold (TG) finish is custom order, call for manufacturing time.
Router bit for flushboltsKTE2DBFORB
7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)
STRIKER FOR INSWING DOORS
© Copyright 2018 • Eclipse Architectural® 21ALL DRAWINGS NO SCALE
FLUSHBOLTS FOR E3 OUTSWING FOLDING DOORS: DBOT SERIES
SELECT FINISH PRODUCT NUMBER DESCRIPTION
bronze powder coat finish on aluminum
KTDBOT200NRQ 8" (200mm) 1” throw, round endKTDBOT400NRQ 16" (400mm) 1” throw, round endKTDBOT600NRQ 24" (600mm) 1” throw, round endKTDBOT1000NRQ 39" (1000mm) 1” throw, round end
brushed metallic finish on aluminum to match stainless steel
KTDBOT200NRX 8" (200mm) 1” throw, round endKTDBOT400NRX 16" (400mm) 1” throw, round endKTDBOT600NRX 24" (600mm) 1” throw, round endKTDBOT1000NRX 39" (1000mm) 1” throw, round end
bright gold finishon aluminum
KTDBOT200NRTG 8" (200mm) 1” throw, round endKTDBOT400NRTG 16" (400mm) 1” throw, round endKTDBOT600NRTG 24" (600mm) 1” throw, round end
SPECIFICATIONSMax wind load: 450kg (990lb) forceMin door thickness: 1-3/4” (44.5mm)Throw length: 1” (25mm)Finishes: Bronze powder coat on aluminum to match pvd bronze finish on E3 hinges. Brushed metallic on aluminum to match stainless steel finish on E3 hinges. Bright gold (TG) finish on aluminum to match pvd brass finish on E3 hinges.
The flush-mounted flushbolts, rounded style and 1” (25mm) throw are designed for use with sliding and folding doors. This flushbolt will resist high winds and is rated to resist a 250kg load in Western Red Cedar and 450kg in Amoora. The bolts are easily installed with a dedicated router bit and are available in three finishes.
PLEASE NOTE: Flushbolt housing & slide bar are manufactured from aluminum components
1” (25mm) throw length regardless of bolt length
INTERIOR
Architectural Detail
2-7/16” (62mm)
13/16” (20.6mm)
7/8”(22mm)
KTE2DBFORB Router bit for flushbolts (dedicated router bits are available)
Bright gold (TG) finish is custom order, call for manufacturing time.
flushbolt machining centered at stile width
R = 1/64” (0.5mm)9/16” (14mm)
CL
1-27/64” (36mm)
1/8”(2.5mm)
3/4”(19mm)
KT749 Flushbolt cup used with floor channel and ADA sill
Flushbolt cup used with floor channel and ADA sillKT749BRONZE bronze powder coatKT749DCH Satin chrome
Bright gold (TG) finish is custom order, call for manufacturing time.
Strike plate for headerKTDBSPQ bronze powder coat KTDBSPS Satin chrome
7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)
1-27/64”(36mm)
43/64” (17mm)
35/64” (14mm)
47/64” (18.6mm)
pin diameter 25/64” (10mm)
35/64” (14mm)
1” (25mm)
Flushbolt Assembly
Actual machining for flushbolts (face plate)1-27/64” x 7-7/8” (36mm x 200mm) 1-27/64” x 23-5/8” (36mm x 600mm)1-27/64” x 15-3/4” (36mm x 400mm) 1-27/64” x 39-3/8” (36mm x 1000mm)
© Copyright 2018 • Eclipse Architectural®22 ALL DRAWINGS NO SCALE
SELECT FINISH PRODUCT NUMBER DESCRIPTION
bright gold finishover aluminum
KTDBSY200NRTG 8” (200mm), 1” throw, round endKTDBSY400NRTG 16” (400mm) 1” throw, round endKTDBSY600NRTG 24” (600mm) 1” throw, round end
powder coat finishbronze overaluminum
KTDBSY200NRQ 8” (200mm) 1” throw, round endKTDBSY400NRQ 16” (400mm) 1” throw, round endKTDBSY600NRQ 24” (600mm) 1” throw, round endKTDBSY1000NRQ 39” (1000mm) 1” throw, round end
brushed metallic finish over aluminum to match stainless steel
KTDBSY200NRX 8” (200mm) 1” throw, round endKTDBSY400NRX 16” (400mm) 1” throw, round endKTDBSY600NRX 24” (600mm) 1” throw, round endKTDBSY1000NRX 39” (1000mm) 1” throw, round end
SPECIFICATIONSMax wind load: 450kg (990lb) forceMin door thickness: 1-3/4” (44.5mm)Bolt lengths: 8”, 16”, 24”, 39” (200mm, 400mm, 600mm, 1000mm)Finishes: Bright gold to match pvd brass hardware bronze powder coat on aluminum to match the pvd bronze hardware & brushed metallic to match stainless steel hardware
INTERIOR
Architectural Detail Flushbolt Assembly (Machining Spec)
2-7/16” (62mm)
13/16” (20.6mm)
7/8”(22mm)
flushbolt machining centered at stile width
R = 1/64” (0.5mm)9/16” (14mm)
CL
1-27/64” (36mm)
1/8”(2.5mm)
3/4”(19mm)
KT749 Flushbolt cup used with floor channel and ADA sill
PLEASE NOTE: Flushbolt housing & slide bar are manufactured from aluminum components
KTE2DBFORB Router bit for flushbolts (dedicated router bits are available)
Flushbolt cup used with floor channel and ADA sillKT749BRONZE bronze powder coatKT749DCH Satin chrome
Strike plate for headerKTDBSPQ bronze powder coat KTDBSPS Satin chrome
7-7/8” (200mm)15-3/4” (400mm)23-5/8” (600mm)39-3/8” (1000mm)
1-31/32”(50mm)
1-27/64”(36mm)
17/32”(13mm)
pin diameter9/16 (14mm)
1” (25mm)
The flush-mounted flushbolts, rounded style and 1” (25mm) throw are designed for use with sliding and folding doors. Symphony™ will resist high winds and is rated to resist a 250kg load in Western Red Cedar and 450kg in Amoora. The bolts are easily installed with a dedicated router bit and are available in three finishes.
Symphony™
FLUSHBOLTS FOR OUTSWING FOLDING DOORS: DBSY SERIESUsed with KT788 ADA Sill and KT23 Floor Channel
Bright gold ( TG) finish is custom order, call for manufacturing time.
Actual machining for flushbolts (face plate)1-27/64” x 7-7/8” (36mm x 200mm) 1-27/64” x 23-5/8” (36mm x 600mm)1-27/64” x 15-3/4” (36mm x 400mm) 1-27/64” x 39-3/8” (36mm x 1000mm)
© Copyright 2018 • Eclipse Architectural® 23ALL DRAWINGS NO SCALE
ECLIPSE E3 DRILLING JIG INSTRUCTIONS3.57mm (9/64”) Drilling for 15mm (19/32”) Pivot / Intermediate / LH & RH Carrier Sets
Align the stiles from ajoining doors next to each other on the bench or similar. Push the 15mm (19/32”) buttons at the first end, then align them hard up to the bottom of the buttons while holding the stiles tight up to each other, then drill holes to depth of screw.
Push all buttons up so the jig can slide to the center where a mark should be added to the stiles. Align the ‘V’ in the side of the jig with the mark on the stile, then drill holes to the depth of screw.
Push all buttons up and slide the jig down the opposite end. Push the 15mm (19/32”) buttons at the other end, then align them hard up to the bottom of the buttons while holding the stiles tight to each other, then drill holes to depth of screw.
Drill all holes using a 3.57mm (9/64”) drill for use with the 10 gauge screws supplied in all Centor sets. Alternatively you can drill the 3.57mm (9/64”) holes for use with 8 gauge screws into aluminum.
Carry out the same steps ( 1, 2 & 3 above) the same as 15mm (19/32”) except using the 60mm (2-3/8”) buttons.
1
1
2
2
3
3
KTE3DJ
SPECIAL ORDER ONLY
© Copyright 2018 • Eclipse Architectural®24 ALL DRAWINGS NO SCALE
ECLIPSE TWINPOINT LOCK & SWING HANDLE
NEW E3 SILLS WITH TWO LOCKING OPTIONS
Flushbolt
Specifications
Function
Style
Testing
The LT2 operates easily with a simple handle rotation, driving a 1” (25mm) throw into the head and sill. This makes it one of the most secure bolt locks on the market. An installed Twinpoint system is completely accessible and serviceable.For people with mobility impairments, the Twinpoint offers the security of two flushbolts, but without the access problems associated with flushbolts being too high or low to reach, and hard-to-grip door handles.
LT2 has the sleek and clean styling synonymous with all Eclipse products. Their low profile allows any folding system, such as F3, E2, E3 or E4 to stack neatly, without intrusive door furniture getting in the way. Eclipse Twinpoint locks are fully concealed within the door stile, avoiding long or hard-to-reach dropbolts fixed to the door face, particularly on tall doors. The Eclipse Twinpoint is an unobtrusive, functional and sleek locking solution.
The Centor LT2 has been tested to 100,000 cycles at maximum configuration to ensure smooth working order beyond their 10 year warranty period. The LT2 Twinpoint locking system has also been exposed to dust, mud, sand and corrosive atmospheres to ensure they stand up to real life use. This includes exposure to salt spray for seaside installations.
Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel.
Minimum door thickness: 1-3/8” (35 mm) / Minimum rod length: 15” (381 mm) / Throw length: 1” (25 mm) / Uses: folding, french & sliding
twinpoint & swing handle
twinpoint & swing handle
twinpoint & swing handle
multipoint &lever lock set
4L 3L
For 1-3/4” (44.5mm) or 2-1/4” (57mm) Door Thickness
The new DBOT flushbolt & Twinpoint lock were designed to utilize the same channel in any of our four new E3 sills, thus giving you the option to now offer your customer the original flushbolt design or the simple hand rotation of the single handle, driving a 1” throw into the head and sill.
KT795 Sill
Channel for 1-3/4” (44.5mm) doorChannel for 2-1/4” (57mm) door
snap in covers for channels
NO SCALENO SCALE
Twinpoint
KT775 Sill
DBOT Series Flushbolt
Twinpoint
© Copyright 2018 • Eclipse Architectural® 25ALL DRAWINGS NO SCALE
LT2 TWINPOINT LOCK & DF3 (ALUMINUM) OR DF4 (STAINLESS STEEL) SWING HANDLESKit Components For Twinpoint Assembly
transmission rod
PLEASE NOTE: When ordering complete TwinPoint Assembly, you are required to order: transmission rod & cover plate, lock/gear box, swing handle & cups.
Twinpoint Lock assembly not available in PVD Brass (TG)
transmission rod
swing handle assembly(6 finishes)
lock/gear box
two finishes available on outer housing cover plate
PRODUCT # DESCRIPTION
EC TwinPoint Lock (LT2 Model) for use with DF3 (Aluminum) & DF4 (Stainless Steel) ModelsECLT2TRSN0924X TwinPoint transmission rod, cover plate and strike plate for 96” (2438mm) door height / brushed metallic aluminum finishECLT2TRSN0924Y TwinPoint transmission rod, cover plate and strike plate for 96” (2438mm) door height / black anodized finishECLT2TRSN0930X TwinPoint transmission rod, cover plate and strike plate for 120” (3048mm) door height / brushed metallic aluminum finishECLT2TRSN0930Y TwinPoint transmission rod, cover plate and strike plate for 120” (3048mm) door height / black anodized finishEC Lock Gear Box for EC TwinPoint (LT2 Model)ECLT2NS Lock/gear box for EC TwinPoint transmission rod, cover plate & handleEC Swing Handle DF3 (Aluminum) Model For EC TwinPoint (LT2 Model)ECDF3SHNAL DF3 swing handle aluminum, black powder coatECDF3SHNAPCN DF3 swing handle aluminum, satin aluminum powder coatECDF3SHNAQ DF3 swing handle aluminum, bronze powder coatEC Swing Handle DF4 (Stainless Steel) Model For EC TwinPoint (LT2 Model)ECDF4SHNSOL DF4 swing handle stainless steel, PVD bronze finishECDF4SHNSS DF4 swing handle stainless steel, brushed finishCup for Sill or Head (Mandatory for Sill, Optional for Head)ECLTBC8SS Brushed S.S. FinishECLTBC8SOL PVD Bronze FinishTL2 Router BitECLT2RB Router bit for LT2 TwinPoint Lock AssemblyEclipse E3 Drilling Jig for E3 Hinge placement on doorKTE3DJ Eclipse E3 drilling jig for wood doorsStrike Plate for Head (For replacement purposes only) One strike supplied with Twinpoint (Standard)ECLTSP8SS Brushed S.S. FinishECLTSP8OL PVD Bronze Finish
© Copyright 2018 • Eclipse Architectural®26 ALL DRAWINGS NO SCALE
LT2 TWINPOINT1-1/16”(27mm)
4-23/32”(120mm)
15-3/4”(400mm)
1-3/4”(44.50mm)
4-23/32”(120mm)
1” (25mm)
Standard = 36” (914mm)Minimum = 15” (381mm)
LT2 Model TwinPoint Lock
DF3 Model TwinPoint Swing Handle (Aluminum)orDF4 Model Twinpoint Swing Handle (Stainless Steel)
E3 Top Track
E3 Floor Channel used in conjunction with Twinpoint
New E3 Sill used in conjuction with Twinpoint
Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel.
Twinpoint & Swing Handle
Twinpoint & Swing Handle
Twinpoint & Swing Handle
Multipoint &Lever Lock Set
4L 3L
© Copyright 2018 • Eclipse Architectural® 27ALL DRAWINGS NO SCALE
WOOD STILE ROUTE PROFILE (OUTSWING APPLICATION) FOR LT2 MODEL
60.0°
9/32” (7.1mm)
5/64” (1.8mm)
Detail A
ECLT2RB Route stile
1-3/4” (44.5mm)
1-3/32”(27.80mm)
32/23”(18.4mm)
1/2”(12.7mm)
5/32”(4mm)
3/32”(2.5mm)
9/16”(14.4mm)
2-1/8”(54mm)
14-11/64”(360mm)
9-1/16” (230.2mm)
R 1/2”(12.7mm)
2-5/64” (53mm)
11/16” (18mm)
standard height9/14”
(36mm)
B
A
A
1-7/64” (28mm)
15/32” (12mm)
1-1/32”(26mm)
R7 9/32”(7.2mm)
3-3/16”(81mm)
4-61/64”(126mm)
13/64”(5mm)
Detail A
Back Set
min 1-3/8” (35mm)
© Copyright 2018 • Eclipse Architectural®28 ALL DRAWINGS NO SCALE
1-11/16”(43mm)
R 13/32”(10.5mm)
13/16”(21mm)
11/64” (4.2mm)
21/64” (8.4mm)
1-3/4” (44.5mm)
19/64” (7.6mm)
E2 / E3 HINGE PLACEMENT OVER TWINPOINT
A A
5/32" (4mm)1-3/32" (27.8mm)
9/16"(14.4mm)
1-3/4" (44.5mm)
SECTION A-A
E2 Hinge
E3 hinge
Strike plate for head
Flushbolt metal cup used with floor channel
ECLTSP8SS Brushed s.s. finishECLTSP8OL PVD bronze finish
ECLTBC8SS Brushed s.s. finishECLTBC8SOL PVD bronze finish
2-13/32”(61mm)
© Copyright 2018 • Eclipse Architectural® 29ALL DRAWINGS NO SCALE
DF3 TwinPoint Swing Handle, Choice of 4 Finishes Over Cast Aluminum
LT2 TwinPoint Housing Cover Plate Finishes
LT2 Transmission HousingBrushed Metallic Aluminum or
Black Anodized finish
Swing HandleDF3: Aluminum handle (4 finishes)DF4: Stainless Steel Handle (2 finishes)
Finishes & MaterialsThe Twinpoint door furniture is available in a range of finishes to suit any door or décor.
Brushed Metallic Aluminum Black Anodized Aluminum
Satin Aluminum Powder Coat Black Powder Coat Bronze Powder Coat
DF4 Twinpoint Swing Handle (SS) Choice of 2 Finishes
PVD bronze over stainless steel
Brushed stainless steel
PLEASE NOTE: For technical reasons associated with color reproduction, the colors shown on this brochure give only an indication of color & finish. No warranty or guarantee can be given that they will exactly match the product as supplied.
Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel.
twinpoint & swing handle
twinpoint & swing handle
twinpoint & swing handle
multipoint &lever lock set
4L
3L
Twinpoint Lock assembly not available in PVD Brass (TG)
LT2 Model Twinpoint
© Copyright 2018 • Eclipse Architectural®FULL SCALE EXCEPT AS NOTED30 FULL SCALE EXCEPT AS NOTED
JAMB TO SILL ASSEMBLY
KT23 OPTIONAL FLOOR CHANNEL APPLICATION FOR OUTSWING OR INSWING DOORSThis application is recommended for interior application, exterior non-rainfall weather conditions or undercover well protected doors. 2-1/4” (57mm) door, outswing application shown. Other door thickness may be used.
screws
jamb
fir top moulding
inserts snap into channel
E3 sill extruded aluminum clear or bronze anodized, with wood substrate and interior top moulding (fir)
DS434 kerf seal
DS434kerf seal
KT768GASKET sill to jamb assembly gasket
KT23BLVEPVC insert, black
KT795COVERBLVEPVC insert, black
KT23DV Floor channel, bronze anodized with PVC insert, blackKT23BLVE PVC insert only, black (replacement part)Lengths available: 111”, 147”, 183”, 222”, 294” (2.81m, 3.73m, 4.64m, 5.63m, 7.46m)
EXTERIOR INTERIOREXTERIOR INTERIOR
DS369A7145BLdual door
bottom pile seals
15/16”(24mm)
KT23CVor KT23DVfloor channel with PVC insert
min door thickness when usingfloor channel is 1-3/8” (35mm)
2-1/4” (57mm)
KT749Flush bolt cup
KT749Flush bolt cup
7/8"(22mm)
7/8"(22mm)
15/16”(24mm)
13/32”(10mm)
13/32”(10mm)
3/16”(4.6mm)
7/8”(22mm)
7/16”(11mm)
1-3/4” (44.5mm)
finished floor line
finished floor line
1/2”(12.7mm)
7/8”(22mm)
7/16”(11mm)
Door height plus 3-3/4” (95.3mm) = R.O. (from finished floor line)door height plus 3-1/4” (82.55mm) = full jamb height
NO SCALE
© Copyright 2018 • Eclipse Architectural® FULL SCALE EXCEPT AS NOTED 31
1-5/16” (33.34mm)KT190Castragalsupplied by Eclipse Architectural
2134mm (84”)2438mm (96”)2743mm (108”)3048mm (120”)clear fir astragal 1-1/8”
(28.5mm)
DSP10835BLKerf inserted fin pile
9/32”(7.14mm)
9/32”(7.14mm)
1/8” (3.23mm)
1-3/4”(44.5mm)
door
kerf slot1/8” x 3/8”(3.18mm x 9.5mm)
DS434inserted weatherseal, brown, white or black
3/8” (9.5mm)
5/16” (7.94mm)
INTERIOR3º bevel on active door ie: 35-7/8” (911mm) inside measurementwidth of door.
36” (914.4mm) outsidemeasurement of door
5/32” (4mm)
INTERIOR
DSP10835BLKerf inserted fin pile
door with astragal
NOSCALE
1/8” (3.23mm)
KT190C WOOD ASTRAGAL DETAIL FOR ECLIPSE E3 INTERIOR FOLDING SYSTEMTriple Seal For Superior Sealing Performance
LATCHING DOOR HOLD (DH)
KT740DHC Clear anodizedKT740DHD Bronze anodized
T-Unit
set screenadjustment screw
main unit
NOTE: For ease of mounting all hardware, it is recommended to use square edge doors.
NO SCALE
NO SCALE
© Copyright 2018 • Eclipse Architectural®32 ALL DRAWINGS NO SCALE
E3 HARDWARE PLACEMENT (4L) Outswing Application
C3 DOOR HOLD MAGNETS(OPTIONAL)
INTERIOR APPLICATIONS: HOW TO DETERMINE SWING OF SYSTEMSThe following is a guideline when determining outswing or inswing applications for the purpose of choosing correct hardware and flushbolts. NOTE: The interior/exterior designation (i.e. 3L) is still used for interior application because it just makes it easier to understand.
FOR EXAMPLE:
Hall Or Living RoomThe above example (3LI) shows the system swinging into the bedroom and flushbolts on the same side. This would be an inswing system and the bedroom side is considered the interior side. Passage set only recommended for the swing door.
Another RoomThe above example (3L) shows the system swinging into another room and flushbolts on the bedroom side. This would be an outswing system and the bedroom side is considered the interior side. Passage set only recommended for the swing door.
The above example (2L2R) is not recommended for interior applications because of the potential of getting locked in a room without any exit. Other configurations not recommended. 2L, 2R, 4L, 4R, 6L, 6R, 8L, 8R; basically pairs or even number or door panels.
INSWING
INTERIOR
EXTERIOR3LI
INTERIOR
EXTERIOR
OUTSWING3L
EXTERIOR
Notaccessible
2L2R
(FLUSHBOLT) BEDROOM SIDE (FLUSHBOLT) BEDROOM SIDEINTERIOR
top pivot
bottom pivot
wall pivot
hingeconcealed intermediate guide
hinge with handle
concealed end guide
weatherseals
intermediate carrier
end carrier
KTE3TPPLATEmounting plate for E3 top pivot assembly
KTDCAS Satin aluminum finishKTDCAOL Black finish KTDCATG Brass finish (custom order, call for manufacturing time)
© Copyright 2018 • Eclipse Architectural® 33ALL DRAWINGS NO SCALE
FLUSHBOLT PLACEMENT
up to 84”(2134mm)
84-1/16”to 96”(2159mmto 2438mm)
96-1/2” to 108” (2403mmto 2743mm)
108-1/16”to 118”(2768mm to2997mm)
8” (200mm)flushbolt
16” (400mm)flushbolt
24” (600mm)flushbolt
39” (1000mm)flushbolt
8” (200mm)flushbolt
8” (200mm)flushbolt
8” (200mm)flushbolt
8” (200mm)flushbolt
Suggested flushbolt lengths for door heights 80” to 118” (2032mm to 2997mm)
NOTE: End user may require longer flushbolts for top of doors for easier reach. When using E2 hardware for folding windows, top flushbolt length must be specified.
Scale: 1/4” = 1ft.
WIDTH1) Jamb to Stud - typical 1/4” (6mm) shimming x 2 = .5” (12mm)2) Jamb thickness 11/16” (17.5mm) x 2 = 1.375” (34.9mm)3) Panel to Jamb - Clearance 9/32” (7mm) x 2 = .5624” (14mm)4) Panel to Panel - Gap 5/32” (4mm) x 3 = .4686” (12mm)5) Panel width 36” (914”) x 4 = 144” (3656mm
HEIGHT6) Frame header to R.O. header. Typical 1/2” (12mm) shimming x 1 = .5” (12mm)7) Frame header 2-21/32” (68mm) x 1 = 2.677” (68mm)8) Top of door panel to frame header 3/16” (5mm) x 1 = .1875” (5mm)9) Door panel height 84” (2134mm) x 1 = 84” (2134mm)10) Bottom of door panel to top of sill 13/32” (10mm) x 1 = .3937” (10mm)11) Sill height 1-3/16” (30.16mm) x 1 = 1.1875 (30.16mm)
Clearances Rough opening specs for E3
Pivot door to jamb 9/32” (7mm)Swing door to jamb 9/32” (7mm)Panel to panel gap 5/32” (4mm)Bottom of door panel to sill 3/8” (9.5mm)Top of door panel to header 3/16” (5mm)Inside face of door panel to stop 3/8” (9.5 mm)
1. Door Height plus 5” (127mm) = R.O. when using inswing or outswing E3 Sills and Frame specs.
2. Door Height plus 4-1/4” (107.9mm) = R.O. when using KT788E3 ADA Sill. 3. Door Height plus 3-3/4” (95.25mm) = R.O. when using E3 floor channel.
Manual calculation for determining R.O. (i.e. configuration 1L3 R, i.e. door panel size 36” x 84” [914mm x 2134mm])
R.O. (width) 146-29/32” or 146.906” or (3731mm) or (3.73m)
R.O. Height 88 15/16” or 88.95” or (2259 mm) or (2.25m)
For O.S.M. width of unit take R.O. minus 1/2” (12mm) i.e. 146-29/32” (3731mm) - 1/2” (12mm) = 146-13/32” (3718mm).
For O.S.M. height of unit take R.O. minus 1/2” (12mm). i.e. 88-15/16” (2259mm) minus 1/2” (12mm) = 88-7/16” (2246mm).
MANUAL DOOR CALC
MAGNETSKTEMAG Magnets for holdingthe door panels in the open position
KTEMAG(sold as pairs)
13/16”(20.6mm)2-3/8”
(60.3mm)
I.E. 5L
door hold
magnets
3L
R.O.
INTERIOR
EXTERIOR
1 1
22
35
4 4 45 5 5
3
R.O. INT.EXT.
1110
9
87
6
© Copyright 2018 • Eclipse Architectural®34 ALL DRAWINGS NO SCALE
E3 PARTS SELECTIONWhen ordering, add color designation (letters) to end of product number: OL: pvd bronze | S: stainless steel | TG: pvd brass
KTE3CPS Pivot sets2 pieces
KTE3EH Interior D pull handlefor inswing doors1 piece
Intermediate carrier sets with additional hinge
KTE3CLCS Left carrier sets2 pieces
KTE3HNHS Hinge sets (FLAT) without middle handle for inswing doors3 pieces
Hinge sets no handle for inswing doors
KTE3CRCS Right carrier sets2 pieces
KTE3HHS Half OFFSET hinge sets with middle handle for outswing doors3 pieces
Half offset hinge sets with handle for outswing doors
KTE3CICS Intermediate carrier sets, 3 pieces
KTE3HHNHS Half offset hinge sets without middle handle for inswing doors 3 pieces
Half offset hinge sets no handle for inswing doors
KTE3WPS Wall pivot set, jamb mounted middle pivot for doors over 88” (2235mm)1 piece
KTE3HS Hinge sets (FLAT) with middle handle for outswing doors3 pieces
Hinge sets with handle for outswing doors
KTE3CBPIVOTH bottom pivot housing only (replacement part)
concealed bottom guide
concealed bottom guide
concealed bottom guide
concealed bottom guide
KTE3HNHSingle hinge, order separately
KTE3HNHSingle hinge, order separately
KTE3HHNHSingle hinge, order separately
KTE3HNHSingle hinge, order separately
KTE3HHNHSingle hinge, order separately
mounted betweentop & bottompivot
PVD brass (TG) finish is custom order, call for manufacturing time.
© Copyright 2018 • Eclipse Architectural® 35ALL DRAWINGS NO SCALE
Number of Hinges for Panel Heights of 80” to 118” (2032mm to 2997mm)
Intermediatecarrier sets
Hinge set or half offset hinge set
Pivot set top & bottom
Up to 96” (2438mm)door height use1, 3, 5
Up to 96” (2438mm)door height use1, 3, 5
Up to 87-15/16” (2234mm)door height use 1 & 5
108-1/16 ” to 118” (2745 to 2997mm)door height use 1, 2, 3, 4, 5
#1 #1
#2 #2
#3 #3
#4 #4
#5 #5
#1
#2
#3
#4
#5
96-1/16” to 108”(2440 to 2743mm)use 1, 2, 3, 5
96-1/16” to 108”(2440 to 2743mm)use 1, 2, 3, 5
88” to 96” (2235 to 2438mm)door height use 1, 3, 5
108-1/16 ” to 118”(2745 to 2997mm)use 1, 2, 3, 4, 5
108-1/16 ” to 118”(2745 to 2997mm)use 1, 2, 3, 4, 5
96-1/16” to 108” (2440 to 2743mm)door height use 1, 2, 3, 5
Pivot Set
Wall Pivot Set Use with above pivot set on doors over 8ft (2438mm) in height
Half Offset Hinge SetMiddle hinge with handle for outswing doors
Hinge Set (Flat)Middle hinge with handle for outswing doors
Intermediate Carrier Set
Right Carrier Set
Left Carrier Set
Single Hinge Half OffsetNo handle for inswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height.
Single Hinge (Flat) No handle for inswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height.
Half Offset Hinge SetNo middle handle for inswing doors
Hinge Set (Flat)No middle handle for inswing doors
Single Hinge Half OffsetWith handle for outswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height
Single Hinge (Flat)With handle for outswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height
2 pieces
1 piece
3 pieces
3 pieces
3 pieces
2 pieces
2 pieces
1 piece
1 piece
3 pieces
3 pieces
1 piece
1 piece
KTE3CPSTG PVD brass KTE3CPSOL PVD bronzeKTE3CPSS stainless steel
KTE3SCREWTG PVD brass KTE3SCREWOL PVD bronzeKTSCREWSS stainless steel
KTE3WPSTG PVD brass KTE3WPSOL PVD bronzeKTE3WPSS stainless steel
KTE3HHSTG PVD brass KTE3HHSOL PVD bronzeKTE3HHSS stainless steel
KTE3HSTG PVD brass KTE3HSOL PVD bronzeKTE3HSS stainless steel
KTE3CICSTG PVD brass KTE3CICSOL PVD bronzeKTE3CICSS stainless steel
KTE3CRCSTG PVD brass KTE3CRCSOL PVD bronzeKTE3CRCSS stainless steel
KTE3CLCSTG PVD brass KTE3CLCSOL PVD bronzeKTE3CLCSS stainless steel
KTE3HHNHTG PVD brass KTE3HHNHOL PVD bronzeKTE3HHNHS stainless steel
KTE3HNHTG PVD brass KTE3HNHOL PVD bronzeKTE3HNHS stainless steel
KTE3HHNHSTG PVD brass KTE3HHNHSOL PVD bronzeKTE3HHNHSS stainless steel
KTE3HNHSTG PVD brass KTE3HNHSOL PVD bronzeKTE3HNHSS stainless steel
KTE3HHTG PVD brass KTE3HHOL PVD bronzeKTE3HHS stainless steel
KTE3HTG PVD brass KTE3HOL PVD bronzeKTE3HS stainless steel
E3 PARTS SELECTION
Replacement Screws for all hinges
PVD brass (TG) finish is custom order, call for manufacturing time.
Head Office & Manufacturing Centre, Vancouver, Canada7470 Buller Avenue, Burnaby, B.C. V5J 4S5 CanadaPhone: (604) 451-1080 • Fax: (604) 451-1140 • [email protected] Vancouver, B.C., please use our toll free numbers: Phone: 1-888-520-9009 Fax: 1-800-567-2887
Branch Office & Distribution Centre, Toronto, CanadaPhone head office toll free 1-888-520-9009 for branch address
Branch Office & Distribution Centre, Los Angeles, CaliforniaPhone head office toll free 1-888-520-9009 for branch address
Eclipse Architectural® Corporate ShowroomsVancouver & Toronto, Canada • Los Angeles, California, USA
Exterior Folding Door Systems