Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
Q.PRO-G3 245-260
1 APT test conditions: Cells at -1000 V against grounded, with conductive metal foil covered module surface, 25 °C, 168 h
2 See data sheet on rear for further information.
Polycrystalline solar module
151 modules tested
Best polycrystallinesolar module 2013
Q.PRO-G2 235
MOD:27898 photon.info/laboratory
Quality Tested
ID. 40032587
high reliabilitylow degradationfrequentproduct surveillance
The new Q.PRO-G3 is the reliable evergreen for all applications. The third module generation from Q CELLS has been optimised across the board: improved output yield, higher operating reliability and durability, quicker installation and more intelligent design.
INNOVATIVE ALL-WEATHER TECHNOLOGY•Maximumyieldswithexcellentlow-lightandtemperaturebehaviour.
•Certifiedfullyresistanttolevel5saltfog
ENDURING HIGH PERFORMANCE•Long-termYieldSecurityduetoAntiPIDTechnology1,Hot-SpotProtect,andTraceableQualityTra.QTM.
•Long-termstabilityduetoVDEQualityTested–thestrictesttestprogram.
SAFE ELECTRONICS•Protectionagainstshortcircuitsandthermallyinducedpowerlossesduetobreathablejunctionboxandweldedcables.
•IncreasedflexibilityduetoMC4-inter-mateableconnectors.theentireproduc-tionprocessfromcellstomoduleswhilemakingQCELLSsolarmodulesforgeryproof.
ProFit-increasinG Glass tecHnoloGy•Reductionoflightreflectionby50%,pluslong-termcorrosionresistanceduetohigh-quality
•Sol-Gelrollercoatingprocessing.
liGHtWeiGHt Quality Frame•Stabilityatwindloadsofupto5400 Pawithamoduleweightofjust19kgduetoslimframedesignwithhigh-tech alloy.
maXimum cost reductions•Upto31%lowerlogisticscostsduetohighermodulecapacityperbox.
eXtended Warranties•Investmentsecuritydueto12-yearproductwarrantyand25-yearlinearperformancewarranty2.
THE IDEAL SOLUTION FOR:Rooftoparraysoncommercial/industrialbuildings
Ground-mountedsolarpowerplants
Rooftoparraysonresidentialbuildings
MECHANICAL SPECIFICATION
PROPERTIES FOR SYSTEM DESIGNMaximum System Voltage VSYS [V] 1000 Safety Class II
Maximum Reverse Current IR [A] 20 Fire Rating C
Wind / Snow Load(in accordance with IEC 61215)
[Pa] 5400 Permitted module temperatureon continuous duty
-40 °C up to +85 °C
QUALIFICATIONS AND CERTIFICATES partner
Q CELLS PERFORMANCE WARRANTY PERFORMANCE AT LOW IRRADIANCE
TEMPERATURE COEFFICIENTS (AT 1000 W/M2, 25 °C, AM 1.5 G SPECTRUM)
Temperature Coefficient of ISC α [% / K] + 0.04 Temperature Coefficient of VOC β [% / K] − 0.30
Temperature Coefficient of PMPP γ [% / K] − 0.42
NOTE: Installation instructions must be followed. See the installation and operating manual or contact our technical service department for further information on approved installation and use of this product.
irradiaNcE [W/m²]
rEla
TivE
Eff
iciE
Ncy
[%
]
Effi
ciEN
cy r
ElaT
ivE
TO
NOm
iNal
pOW
Er [
%] 100
97
95
90
85
80
75
yEars0 5 10 15 20 25
ElEcTrical cHaracTErisTicspErfOrmaNcE aT sTaNdard TEsT cONdiTiONs (sTc: 1000 W/m², 25 ̊c, am 1.5 G spEcTrUm)1
NOmiNal pOWEr (+5 W / -0 W) [W] 245 250 255 260
average power pmpp [W] 247.5 252.5 257.5 262.5
short circuit current isc [a] 8.52 8.71 8.90 9.09
Open circuit voltage vOc [v] 37.15 37.49 37.83 38.18
current at pmpp impp [a] 8.05 8.21 8.37 8.53
voltage at pmpp vmpp [v] 30.75 30.76 30.77 30.78
Efficiency (Nominal power) η [%] ≥ 14.7 ≥ 15.0 ≥ 15.3 ≥ 15.6
pErfOrmaNcE aT NOrmal OpEraTiNG cEll TEmpEraTUrE (NOcT: 800 W/m², 45 ± 3 ̊c. am 1.5 G spEcTrUm)2
NOmiNal pOWEr (+5 W / -0 W) [W] 245 250 255 260
average power pmpp [W] 182.4 186.0 189.7 193.4
short circuit current isc [a] 6.87 7.03 7.18 7.33
Open circuit voltage vOc [v] 34.58 34.90 35.22 35.54
current at pmpp impp [a] 6.32 6.44 6.56 6.68
voltage at pmpp vmpp [v] 28.86 28.89 28.92 28.941 Measurement tolerances STC: ± 3 % (Pmpp); ± 10 % (Isc, Voc, Impp, Vmpp)
100 200 300 400 500 600 700 800 900 1000
105
100
95
90
85
80
Irradiance [W/m²]
Rela
tive
effic
ienc
y [%
]100
95
90
85
80
75
155 25200 10
97
RELA
TIVE
MOD
ULE
EFF
ICIE
NCY
COM
PARE
D TO
NOM
INAL
POW
ER [
%]
YEARS
Q CELLS
Industry standard
Best competitor
Format 65.7 in × 39.4 in x 1.38 in (including frame)(1670 mm × 1000 mm × 35 mm)
Weight 41.89 lb (19.0 kg)
Front Cover 0.13 in (3.2 mm) thermally pre-stressed glasswith anti-reflection technology
Back Cover Composite film
Frame Anodized aluminum
Cell 6 × 10 polycrystalline solar cells
Junction box Protection class IP67, with bypass diodes
Cable 4 mm² Solar cable; (+) ≥ 45.67 in (1160 mm), (-) ≥ 45.67 in (1160 mm)
Connector SOLARLOK PV4, IP68
Product label
≥ 45.67" (≥ 1160 mm)
38.6" (980 mm)
5.91" (150 mm)
37
.76
" (9
59
mm
)
mou
ntin
g sl
ots
and
grou
ndin
g ho
les
1.38" (35 mm)
6 × grounding holesØ 0.177" (4.5 mm)
65.7" (1670 mm)
39
.4"
(10
00
mm
)
Junction bo×
4 × mounting slotsDETAIL A
8 × Drainage holes
Cable withconnectors
Frame
DETAIL A0.630" (16 mm)
0.315" (8 mm)0.799" (20.3 mm)
NA
CertifiedUL 1703(254141)
UL1703;VDEQualityTested;CE-compliant;IEC61215(Ed.2);IEC61730(Ed.1)applicationclassA
Spe
cific
ationssub
jecttotech
nicalc
hang
es©
Han
wha
Q C
ELLS
Gm
bHQ.PRO-G3_2
014-07_R
ev04_N
A
Atleast97%ofnominalpowerduringfirstyear.Thereaftermax.0.6%degra-dationperyear.Atleast92%ofnominalpowerafter10 years.Atleast83%ofnominalpowerafter25 years.
Alldatawithinmeasurementtolerances.FullwarrantiesinaccordancewiththewarrantytermsoftheQCELLSsalesorganisationofyourrespectivecountry.
Thetypicalchangeinmoduleefficiencyatanirradianceof200W/m²inrelationto1000W/m²(bothat25°CandAM1.5Gspectrum)is-2%(relative).
Hanwha Q CELLS USA Corp.8001IrvineCenterDrive,suite1250,IrvineCA92618,USA|TEL +18487485996|FAX +19497485984|EMAIL [email protected]|WEB www.q-cells.us
CertifiedUL 1703(254141)