Hand tools - katalog.hhw.dekatalog.hhw.de/EN/50_HHW_Katalog_2010_eng.pdf · ß Hand tools eng/OP 50.3 5 The new generation of wrenches Adjustable wrenches DIN 3117 Open-end, ring

5

Hand tools

• Open-end wrenches and ring wrenches

• Ratchet wrenches• Hook wrenches• Socket wrenches

• Insert tools and socket accessories

• Servo screwdriver insert tools and socket accessories

• Wrenches• Screw extractors

• Screwdrivers• Bits and bit tools• Impact screwdrivers

• Bar clamps• Hand vices• Bench vices• Vice height adjustment

units• Jaw caps

• Hammers • Double face blacksmith's hammer

• Centre punches • Drift punches • Drive pin punches • Chisels • Blind riveting tools

• Torque screwdrivers• Torque wrenches• Torque multipliers• Torque insert tools• Torque testing instruments• Torque calibration systems

• Holding tongs• Snap ring (circlip) pliers• Waterpump pliers• Pipe wrenches• Welder's gripping pliers• Self-locking multi-purpose

pliers

• Carpenter's pincers• Rabitz pincers• End cutters• Centre cutting nippers• Diagonal cutting pliers• Bolt cutters

• Safety programmeNon-sparking tools

• Tool sets

50

51

52

53

54

55

56

57

58

59

50.3 – 50.34

51.1 – 51.80

52.1 – 52.50

53.1 – 53.12

54.1 – 54.22

55.1 – 55.30

56.1 – 56.28

57.1 – 57.10

58.1 – 58.4

59.1 – 59.24

eng/OP

Our suppliers for catalogue group 5:

0

ß

j

m

,

$O

K

P

u

J

B

N

O

R

VÄ

:LEINEN

METRINCH®

b

j K

Z

Schlegel/EMF

&

X

s

+

ß Hand tools

eng/OP www.hhw.de 50.3

5

The new generation of wrenches

Adjustable wrenches DIN 3117

Open-end, ring and socket wrenches aremanufactured with a profile, providinglarger contact surfaces with the screwheads. The forces are transmitted intangential direction onto the flanks of thescrew heads and nuts. A maximum ofload distribution is ensured and dama-ges on tools and workpieces are mostlyavoided. Even older and weak screwscan be fastened by using these newprofiles.

. Also fits screws outside of thetolerance range

. Preserves screw heads – no edgedeformation thanks to theapplication of force on thesurface

. Highest force transmissionthanks to larger contact surface

. Even loosens damaged screwheads

0 Energy-Profil

, Dynamic-Drive Profil

J OGV®-Profil

N UnitDrive-Profil

V Tractionsprofil

Anti-Slip-Drive-Profil

Metrinch® Metrinch-Wellenprofil

50004

0TypeVery low weight and ergonomical design. Reducesthe pressure on the palm. Extremely large clam-ping width and 45 % more torque. With measuringscale.QualityChrome-vanadium steel, drop-forged.

50005

0TypeAngled head 22°, clockwise operation. Nickel andchrome-plated, mirror finish.QualityChrome-alloy steel.

50006ßTypeAngled head 22°, clockwise operation, withmeasuring scale and plastic handle. Nickel-platedand chrome-plated, highly polished.

QualityChrome-vanadium steel.

50008 101-104,TypeAngled head 15°. Double as pipe wrench by meansof moving the mobile, serrated jaw towards theinside. With measuring scale in mm and ergonomi-cally shaped handle made of thermoplastic elasto-mer. Chrome-plated, hardened, corrosion-proof.

50008 105-106,TypeAngled head 15°. 40% larger opening whencompared to standard adjustable wrenches of thesame size. Low weight, slim head and hardenedjaws. With measuring scale in mm and ergonomical-ly shaped handle made of thermoplastic elastomer.Chrome-plated, precision-hardened, corrosion-proof.

50004

50005

50006

0Length Size 50004 …

mm mm150 24,0 101200 28,7 102250 33,0 103300 38,5 104

0Length Size 50005 …

mm mm110 13,0 201162 20,0 202211 24,0 203260 29,0 204310 34,0 205

ßLength Size 50006 …

mm mm110 13,0 101150 19,5 102200 24,5 103250 29,0 104300 34,0 105

,Length Size 50008 …

mm mm158 21,0 101208 28,0 102257 33,0 103308 35,0 104170 32,0 105218 38,0 106

50004 - 50008

Single open-end wrenches DIN 894

TypeSectional shank, angled head 15°, burnished.

QualitySpecial steel.

50101

Size Length 50101 …mm approx. mm

6 75 3017 80 3028 95 3039 100 304

10 105 30511 115 30612 125 30713 135 30814 140 309


15 145 31016 145 31117 151 31218 151 31319 170 31421 195 31522 195 31624 215 31727 240 318


30 260 31932 275 32034 275 32136 305 32241 340 32346 380 32450 410 32555 440 32660 477 327


65 510 32870 575 32975 610 33080 650 33185 695 33290 695 33395 845 334

100 850 335

50101

50008 101-104

50008 105-106

eng/OP

• Double open end wrench

www.hhw.de50.4

5

Double open-end wrench DIN 895

TypeSectional shank, angled head 15°, burnished.

QualitySpecial steel.

50102


6 x 7 95 1017 x 8 110 1028 x 9 110 104

8 x 10 115 10510 x 11 125 10810 x 13 115 11012 x 13 140 11412 x 14 140 11513 x 14 145 116


13 x 15 150 11713 x 17 155 11914 x 17 160 12116 x 17 160 12216 x 18 160 12317 x 19 170 12418 x 19 170 12619 x 22 195 12819 x 24 215 129


20 x 22 195 13022 x 24 220 13324 x 27 245 13624 x 30 265 13727 x 32 270 14030 x 32 275 14130 x 36 305 14334 x 36 305 14536 x 41 345 146


41 x 46 390 14746 x 50 420 14850 x 55 440 14955 x 60 480 15065 x 70 580 15175 x 80 665 152

50102

Sets of double open-end wrenches DIN 3110, ISO 10102

TypeAngled head 15°, chrome-plated. In cardboard box.


50105

Set contents 50105 …Size mm

8-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 10110-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 10311-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 30 x 32 10412-part 6 x 7 / 8 x 9 / 10 x 11 / 10 x 13 / 12 x 13 / 14 x 15 / 16 x 17 / 17 x 19 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 10512-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 25 x 28 / 30 x 32 106

50105

Set of double open-end wrenches DIN 3110, ISO 10102

0TypeAngled head 15°, chrome-plated, with flat heads.


50106


8-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 09910-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 1007-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 1019-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 102

11-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x23 / 24 x 27 / 30 x 32 10312-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 25 x 28 / 30 x 32 10412-part 6 x 7 / 8 x 9 / 10 x 11 / 10 x 13 / 12 x 13 / 14 x 15 / 16 x 17 / 17 x 19 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 105

50106

Performance requires quality.www.atorn.com

Adjustable wrenches by ATORN:

ATORN‘s high-quality hand tools.

ß Hand tools


5


TypeJaw angle 15°, extreme load capacity thanks todouble-T profile. Chrome-plated on top of nickel.Anti-slip surface. In clip holder.

QualityChrome-alloy steel.

50109


11-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 21 / 19 x 22 / 24 x 27 / 30 x 32 / 34 x 36 105

50109


VTypeAngled head 15°, chrome-plated. In clip holder.QualityChrome-vanadium steel.

50110 101 50110 104 50110 106


8-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 21 x 22 101in drawer module made of plastics, 340 x 170 mm

11-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 21 x 22 / 24 x 27 / 30 x 32 / 34 x 36 104in drawer plastic fitting 340 x 340 mm

12-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 26 / 25 x 28 / 27 x 32 105in cardboard box

12-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 25 x 28 / 30 x 32 106in plastic holder

50110


,TypeAngled head 15°, polished, mirror-finished andnickel-polished, chrome-plated, very flat heads.

QualityVanadium extra.

50112

Set contents Packing 50112 …Size mm

8-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 in holder 10110-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 in holder 10212-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 25 x 28 / 30 x 32 in holder 103

50112


NTypeAngled head 15°, chrome-plated, with flat, finelyground heads.QualityVanadium 31 CrV3.

50108 101 50108 102

Set contents Packing 50108 …Size mm/inch

8-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 in cardboard box 1008-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 in holder 101

12-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 25 x 28 / 30 x 32 in cardboard box 10212-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 25 x 28 / 30 x 32 in cardboard box 103

inch/ 8-part 1/4 x 5/16 / 5/16 x 3/8 / 7/16 x 1/2 / 9/16 x 5/8 / 19/32 x 11/16 / 3/4 x 25/32 / 13/16 x 7/8 / 15/16 x 1 in cardboard box 104

50108

eng/OP

• Double open end wrench

www.hhw.de50.6

5

Double open-end wrench DIN 3110, ISO 10102

TypeAngled head 15°, chrome-plated, with flat heads,slim design.QualityChrome-vanadium steel.

50113

050114

50115NTypeFinely ground heads.

50116

TypeExtreme load capacity thanks to double-T profile.Chrome-plated on top of nickel. Anti-slip surface. QualityChrome-alloy steel.

50117VTypeSlim heads, shank with extra sturdy double T profile.

50118,TypePolished, mirror-finished and nickel-polished,chrome-plated.

50113

50115

50116

50117

50118

0 N VSize 50113 … 50114 … 50115 … 50116 … 50117 … 50118 …mm

4 x 5 101 101 401 4015 x 5,5 102 402 4035,5 x 7 103 103 404

6 x 7 204 104 104 104 404 4057 x 8 105 105 4068 x 9 206 106 106 106 406 407

8 x 10 207 107 107 107 407 40810 x 11 208 108 108 108 408 40910 x 13 209 109 109 109 409 41111 x 13 210 110 110 11012 x 13 211 111 111 111 411 41312 x 14 212 112 112 112 41413 x 14 213 113 113 41513 x 15 214 114 114 114 41613 x 16 11513 x 17 216 116 116 116 416 41814 x 15 217 117 117 117 417 41914 x 17 218 118 118 118 42016 x 17 219 119 119 119 419 42116 x 18 220 120 120 120 420 42217 x 19 221 121 121 121 421 42318 x 19 222 122 122 122 422 42418 x 21 123 12319 x 22 224 124 124 124 42619 x 24 225 125 125 42720 x 22 226 126 126 126 426 42821 x 22 42721 x 23 228 128 128 128 428 42921 x 24 12922 x 24 230 130 130 130 430 43124 x 26 231 131 131 131 43124 x 27 232 132 132 132 432 43324 x 30 133 43425 x 28 235 135 135 135 435 43527 x 30 236 136 136 136 43627 x 32 237 137 137 137 437 43730 x 32 238 138 138 138 438 43830 x 34 13930 x 36 241 14132 x 36 242 142 142 142 442 44134 x 36 143 143 44336 x 41 244 144 144 144 444 44341 x 46 245 145 145 145 445 44546 x 50 146 446 446

50113 - 50118

50114

ß Hand tools


5

Double open-end wrenches DIN 3110, ISO 10102 (inch)

NTypeImperial sizes, angled head 15°, chrome-plated,with flat, finely ground heads.

QualityVanadium 31CrV 3.

50119

Size Length 50119 …inch approx. mm

1/4 x 5/16 122 1015/16 x 3/8 140 1023/8 x 7/16 157 1037/16 x 1/2 172 1041/2 x 9/16 190 105


9/16 x 5/8 190 10619/32 x 11/16 205 107

5/8 x 11/16 205 1085/8 x 3/4 222 109

11/16 x 3/4 222 110


7/8 x 15/16 250 11215/16 x 1 266 1131 x 1.1/8 280 114

1.1/16 x 1.1/4 302 1151.5/16 x 1.1/2 328 116

50119

Double open-end wrenches DIN 3110, ISO 10102 (inch)

,TypeImperial sizes, angled head, nickel-plated andchrome-plated, highly polished, with extremely flatheads.QualityVanadium-extra.

50125 101TypeSet, 8-part, in plastic clip.

50125 201-217TypeSingle.

50125 101

50125 201-217

Set contents 50125 …Size inch

8-part 1/4 x 5/16 / 5/16 x 11/32 / 3/8 x 7/16 / 1/2 x 9/16 / 19/32 x 11/16 /5/8 x 3/4 / 13/16 x 7/8 / 15/16 x 1 101

Size Length Head thickness 50125 …inch mm mm

1/4 x 5/16 130 3,4 2015/16 x 11/32 140 3,7 202

3/8 x 7/16 157 4,0 2037/16 x 1/2 172 4,3 2041/2 x 9/16 180 4,5 205


9/16 x 5/8 190 5,0 20619/32 x 11/16 205 5,3 207

5/8 x 3/4 205 5,8 2083/4 x 7/8 236 6,3 210

25/32 x 13/16 236 6,3 211


7/8 x 15/16 266 7,4 21315/16 x 1 266 7,4 2141 x 1.1/8 280 8,0 215

1.1/16 x 1.1/4 300 8,6 2161.1/4 x 1.3/8 345 10,0 217

50125

Small double open-end wrenches

NTypeAngled head 15° and 75°, chrome-plated, with flat,finely ground heads. Set in plastic pouch.

QualityVanadium 34 CrMo 4.

50134


10-part 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 101

Size Length Head thickness 50135 …mm approx. mm mm

4 x 4 70 1,8 1014,5 x 4,5 70 1,8 102

5 x 5 78 1,8 1035,5 x 5,5 78 1,8 104

6 x 6 78 1,8 105


7 x 7 91 1,8 1068 x 8 96 2,8 1079 x 9 103 2,8 108

10 x 10 105 2,8 10911 x 11 116 2,8 110


12 x 12 116 2,8 11113 x 13 131 2,8 11214 x 14 131 2,8 113

50134 - 50135


Screwdrivers by ATORN:


eng/OP

• Claw wrenches • Striking-face (slogging) open end wrenches • Combination Wrenches

www.hhw.de50.8

5

Claw wrenches

NTypeOffset open-end wrench, chrome-plated.ApplicationFor working in hard-to-reach places.


Note:Straight shafts (tommy bars) see cat.-no. 50749 -50750.

50150

Size L a b d1 d2 Straight shaft (tommy bar) Ø 50150 …mm mm mm mm mm mm mm

13 160 5,5 28 8,5 14 8 10114 160 5,5 28 8,5 14 8 10217 200 6,0 33 10,5 17 10 10319 200 7,0 37 12,5 20 12 10422 200 8,0 42 12,5 20 12 10524 250 9,0 46 14,5 24 14 10627 250 10,0 52 14,5 24 14 10730 250 11,0 57 16,5 28 16 10832 250 12,0 61 16,5 28 16 10936 315 13,0 68 19,0 31 18 11041 315 14,0 76 19,0 31 18 111

b

d1

d2

L

a

50150

Striking-face (slogging) open-end wrenches DIN 133

NApplicationFor heavy-duty applications.

QualityTempering steel. 50170


27 180 16,5 20130 190 17,0 20232 195 17,5 20334 195 17,5 20436 210 18,5 20541 225 19,5 20646 255 20,0 20750 280 21,5 20855 315 24,5 20960 320 24,5 21065 350 28,0 21170 370 30,0 21275 400 31,5 21380 405 34,5 21485 405 34,5 215

50170

www.atorn.com

Performance requires quality.



ß Hand tools


5

Set of combination wrenches DIN 3113 A, ISO 7738 A

TypeRing end 15° offset, chrome-plated. In cardboardbox.

QualityChrome-vanadium steel. 50294


8-part 8 / 9 / 10 / 11 / 13 / 14 / 17 / 19 10112-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 17 / 19 / 22 10312-part 10 / 11 / 12 / 13 / 14 / 17 / 19 / 22 / 24 / 27 / 30 / 32 10417-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 10517-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 22 / 24 106

50294


0TypeRing end with Energy profile and 15° offsethead, slim, flat heads, chrome-plated, in cardboardbox.



8-part 8 / 9 / 10 / 11 / 13 / 14 / 17 / 19 10011-part 6 / 7 / 8 / 10 / 11 / 13 / 14 / 16 / 17 / 18 / 19 10117-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 10217-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 22 / 24 10312-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 17 / 19 / 22 10412-part 10 / 11 / 12 / 13 / 14 / 17 / 19 / 22 / 24 / 27 / 30 / 32 105

50295

Set of combination wrenches DIN 3113 B, ISO 7738 B

NTypeRing end with UD profile and 10° offset head,slim, flat heads, chrome-plated, rings polished, incardboard box.QualityVanadium 31CrV 3.

50297


8-part 8 / 9 / 10 / 11 / 13 / 14 / 17 / 19 1008-part 10 / 12 / 13 / 14 / 17 / 19 / 22 / 24 101

17-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 10226-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 / 111

23 / 24 / 25 / 26 / 27 / 28 / 29 / 30 / 32

50297


TypeRing end with AS-Drive profile and 15° offset,extreme load capacity thanks to double-T profile.Chrome-plated on top of nickel. Anti-slip surface.

QualityChrome-alloy steel. 50298


6-part 7 / 8 / 10 / 13 / 17 / 19 in clip holder 10113-part 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 17 / 19 / 22 / 24 in clip holder 10516-part 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / in cardboard box 107

21 / 22 / 24

50298

eng/OP

• Combination wrenches

www.hhw.de50.10

5

Set of combination wrenches DIN 3113 B, ISO 7738 B

VTypeDouble hexagonal ring end and 10° offset head,slim, flat heads, chrome-plated, rings polished. Indrawer plastic fitting 340 x 340 mm.QualityChrome-vanadium steel.

50299


18-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 / 24 / 27 101

50299


VTypeRing end 15° offset, with Tractions profile,chrome-plated, rings polished, slim, flat heads.Quality Chrome-vanadium steel.

50300 101 Type in drawer module made of plastics, 340 x 170 mm

50300 102-103TypeIn cardboard box.

50300 104TypeIn sturdy plastic holder with convenient carryinghandle. Suitable for wall mounting.

50300 102-103

50300 104


8-part 10 / 11 / 13 / 14 / 15 / 17 / 19 / 22 10112-part 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 10217-part 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 / 24 / 27 10312-part 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 104

50300


,TypeRing end with Dynamic-Drive profile and 15°offset head. Polished, mirror-finished and nickel-po-lished, chrome-plated.QualityVanadium-extra.

50302 197TypeIn convenient black plastic wall mount with carryinghandle and locking device.

50302 201-202TypeIn plastic pouch.

50302 201

50302 197


12-part 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 19717-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 20126-part 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 / 23 / 24 / 25 / 26 / 27 / 28 / 29 / 30 / 32 202

50302

50300 101

ß Hand tools


5

0 N V V ,Size 50304 … 50305 … 50307 … 50308 … 50309 … 50310 … 50311 …mm

5,5 x 5,5 100 1006 x 6 101 201 101 101 401 102 4027 x 7 102 202 102 102 402 103 4038 x 8 103 203 103 103 403 104 4049 x 9 104 204 104 104 404 105 405

10 x 10 105 205 105 105 405 106 40611 x 11 106 206 106 106 406 107 40712 x 12 107 207 107 107 407 108 40813 x 13 108 208 108 108 408 109 40914 x 14 109 209 109 109 409 110 41015 x 15 110 210 110 110 410 111 41116 x 16 111 211 111 111 411 112 41217 x 17 112 212 112 112 412 113 41318 x 18 113 213 113 113 413 114 41419 x 19 114 214 114 114 414 115 41520 x 20 115 215 115 115 116 41621 x 21 116 216 116 116 416 117 41722 x 22 117 217 117 117 417 118 41823 x 23 118 11924 x 24 118 218 118 119 418 120 41925 x 25 120 12126 x 26 12227 x 27 119 219 119 122 419 123 42028 x 28 12429 x 29 12530 x 30 120 220 120 125 420 126 42332 x 32 121 221 121 126 421 127 42434 x 34 122 128 128 42536 x 36 123 130 12941 x 41 124 132 13046 x 46 125 133

Combination wrenches DIN 3113 A/B, ISO 7738 A/B50304 - 50311

TypeDouble hexagonal ring end (size 5,5 - 9 mm withhexagonal ring end), chrome-plated, slim, flatheads.QualityChrome-vanadium steel.

50304TypeRing end 15° offset.

50305

0TypeRing end with Energy profile and 15° offsethead.

50307NTypeRing end with UD profile, 10° offset.QualityVanadium 31CrV 3.

50308

TypeRing end with AS-Drive profile and 15° offset,extreme load capacity thanks to double-T profile.Chrome-plated on top of nickel. Anti-slip surface. QualityChrome-alloy steel.

50309VTypeShort, ring end 10° offset.

50310VTypeLong, ring end 15° offset, slim, with Tractionsprofile. Shank with extra sturdy double T profile.

50311,TypeRing end with Dynamic-Drive profile, 15° offsethead. Polished, mirror-finished and nickel-polished,chrome-plated.

50304

50305

50307

50308

50309

50310

50311

eng/OP


www.hhw.de50.12

5


8 x 8 170 1039 x 9 180 104

10 x 10 190 10511 x 11 200 10612 x 12 210 10713 x 13 225 10814 x 14 235 109


15 x 15 250 11016 x 16 265 11117 x 17 280 11218 x 18 295 11319 x 19 310 11421 x 21 340 11622 x 22 350 117


24 x 24 400 11927 x 27 450 12230 x 30 480 12432 x 32 500 12534 x 34 520 12636 x 36 550 12741 x 41 600 128

Combination wrenches (long)

,TypeRing end with Dynamic-Drive profile, 15° offsethead. Extremely long lever arm. Polished, mirror-fi-nished and nickel-polished, chrome-plated. Set incardboard box.

QualityVanadium-extra.

50320

50321Set contents 50320 …Size mm

8-part 8 / 9 / 10 / 11 / 13 / 14 / 17 / 19 101


8 x 8 180 1019 x 9 180 102

10 x 10 200 10311 x 11 200 10412 x 12 225 10513 x 13 225 10614 x 14 250 107


15 x 15 250 10816 x 16 280 10917 x 17 280 11018 x 18 280 11119 x 19 310 11221 x 21 310 11322 x 22 350 114


24 x 24 400 11527 x 27 450 11630 x 30 500 11732 x 32 500 11836 x 36 550 11938 x 38 550 120

50320 - 50321

Combination wrenches

,TypeFlat shank, chrome-plated and nickel-plated.Special narrow dimensions. Hexagon ring end15° offset, highly polished. Angled head 22,5°.

ApplicationFor radio, telecommunication, electrics, precisionmechanics, carburettors, etc.QualityVanadium-extra steel.

50330

Size Overall length 50330 …mm approx. mm

3,2 x 3,2 70 2023,5 x 3,5 70 203


4,0 x 4,0 70 2044,5 x 4,5 80 205


5,0 x 5,0 80 2065,5 x 5,5 80 207

50330

Combination wrenches

JTypeRatchet wrench. On one side a 15° offset ring end,on the other side an open-end head. ApplicationThe quick-action open-end head is used as aratchet:

Tighten the nut without removing the wrench (1),automatic -grip- to the next edge for a new tighte-ning movement (2). The nut is not tightened asusual via the edge, but via the surface. The insidearea of the open-end wrench provides an additionalrest.

The OGV® profile of the ring end treats the screwgently and increases the service life of the tool.

50335


9-part 8 / 9 / 10 / 11 / 12 / 13 / 14 / 17 / 19 in roll bag 10217-part 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 / 23 / 24 103

50335 - 50340

Combination wrenches (long)

NTypeRing end with UD profile, 15° offset and polished.Extremely long lever arm, chrome-plated. Set incardboard box.

QualityVanadium 31CrV 3. 50314


12-part 10 / 11 / 12 / 13 / 14 / 17 / 19 / 22 / 24 / 27 / 30 / 32 101

50314 - 50315

ß Hand tools


5

,TypeImperial sizes, ring end with Dynamic-Driveprofile and 15° offset, angled head 15°. Nickeland chrome-plated, mirror finish.QualityVanadium-extra.

50345 101TypeSet, 8-part, in plastic pouch.

50345 102TypeSet, 11-part, in plastic pouch.

50345 201-217TypeSingle.

50345 101-102

50345 201-217

Set contents 50345 …Size inch

8-part 3/8 / 7/16 / 1/2 / 9/16 / 5/8 / 11/16 / 3/4 / 7/8 10111-part 3/8 / 7/16 / 1/2 / 9/16 / 5/8 / 11/16 / 3/4 / 13/16 / 7/8 / 15/16 / 1 102

Size Length 50345 …inch mm

1/4 95 2015/16 115 2023/8 125 203

7/16 145 2041/2 170 205

9/16 185 206


5/8 205 20711/16 220 208

3/4 245 20913/16 265 210

7/8 265 21115/16 300 212


1 330 2131.1/16 330 2141.1/8 370 2151.1/4 390 216

1.5/16 415 217

Set of METRINCH® socket and combination wrenches

Type76-part, with 6-point wave profile, mirror chromefinish, in plastic box made of impact- and break-pro-of PP.QualityChrome-vanadium steel, 46 CrV4.

Note:Technical information see cat.- no. 50355.

Set contents:x9 socket wrench bits short (mm + inch):5+3/16 / 6+1/4 / 7+9/32 / 8+5/16 / 9+11/32 / 10+3/8 / 11+7/16 / 12+15/32 / 13+1/2,8 socket wrench bits long (mm + inch):5+3/16 / 6+1/4 / 7+9/32 / 8+5/16 / 9+11/32 / 10+3/8 / 11+7/16 / 12+15/32,1 reversible ratchet,1 extension piece, 50 mm,1 Cardan joint,1 socket handle,1 adapter, 3/8 inch inner square, 1/4 inch outer square.

w11 socket wrench bits short (mm + inch):10+3/8 / 11+7/16 / 12+15/32 / 13+1/2 / 14+9/16 /15+19/32 / 16+5/8 / 17+11/16 / 19+3/4 / 20/21+3/16 /22/23+7/8,7 socket wrench bits long (mm + inch):10+3/8 / 11+7/16 / 13+1/2 / 14+9/16 / 17+11/16 /19+3/4 / 22/23+7/8,2 socket wrench bits for spark plugs (mm +inch): 16+5/8 / 20,8+13/16,1 reversible ratchet, 64 teeth,1 extension piece, 75 mm,1 Cardan joint.v17 socket wrench bits short (mm + inch):10+3/8 / 11+7/16 / 12+15/32 / 13+1/2 / 14+9/16 /15+19/32 / 16+5/8 / 17+11/16 / 18+23/32 / 19+3/4 /20/21+13/16 / 22/23+7/8 / 24+15/16 / 25+1 /26/27+1.1/16 / 29/30+1.3/16 / 31/32+1.1/4,11 combination wrenches (mm + inch):10+3/8 / 11+7/16 / 12+15/32 / 13+1/2 / 14+9/16 /15+19/32 / 16+5/8 / 17+11/16 / 18+23/32 / 19+3/4 /20/21+13/16,1 reversible ratchet, 22 teeth,1 extension piece, 255 mm,1 T-sliding piece.

50350

Set contents 50350 …

76-part 101

50350

Combination wrench DIN 3113 A, ISO 7738 A (inch)50345

50340

(1) (2)

Size Length 50340 …mm mm

8 130 1019 137 102

10 145 10311 153 10412 161 10513 170 10614 178 10715 185 10816 193 109


17 200 11018 208 11119 216 11220 224 11321 233 11422 248 11523 258 11624 268 117

eng/OP


www.hhw.de50.14

5

Set of METRINCH® socket wrenches

Type37-part, with 6-point wave profile, mirror chromefinish, in plastic box made of impact- and break-pro-of PP. QualityChrome-vanadium steel, 46 CrV 4.

Note:The METRINCH® wave profile allows a snug fit andfrictional connection of the wrench on the flanks andnot on the edges. This will have a positive effect onthe service life of the screw and allows for aconsiderably higher force transmission. The waveprofile protects against accidents, even underextreme working conditions. Edges might becomeround, flanks can not.

Set contents: 8 socket wrench bits short (mm+inch): 5+3/16 / 6+1/4 / 7+9/32 / 8+5/16 / 9+11/32 / 10+3/8 / 11+7/16 / 12+15/32,1 Reversible ratchet, 50 teeth, 1 Cardan joint, 1 Extension piece, 50 mm, 1 Adapter,1/4 inch inner square, 3/8 inch outer square. 1 Socket handle, 1 Extension, 100 mm Wobble, 1 T-sliding piece. 1 Bit holder, 4 Bits for slotted screws 4,0 / 4,5 / 5,5 / 6,5 mm, 4 Bits for Phillips recess head screws PH 0 / 1 / 2 / 3, 2 Bits for Phillips recess head screws PZ 1 / 2, 5 Bits for Allen screws size 2,5 / 3 / 4 / 5 / 6 mm, 6 Bits for Torx screws TX 10 / 15 / 20 / 25 / 27 / 30.

50355


37-part 101

50355

Sets of METRINCH® combination wrenches

TypeWith 6-point wave profile, mirror chrome finish, inplastic roll bag.QualityChrome-vanadium steel, 46 CrV4.

Note:Technical information see cat.-no. 50355.

50360Type10-part, contents (mm + inch):10+3/8 / 11+7/16 / 12+15/32 / 13+1/2 / 14+9/16 /15+19/32 / 16+5/8 / 17+11/16 / 18+23/32 / 19+3/4.

50365Type14-part, contents (mm + inch):Similar to cat.-no. 50360, but additionally with8+5/16 / 9+11/32 / 20/21+13/16 / 22/23+7/8.

50370Type15-part, contents (mm + inch):8+5/16 / 9+11/32 / 10+3/8 / 11+7/16 / 12+15/32 /13+1/2 / 14+9/16 / 15+19/32 / 17+11/16 / 19+3/4 /22/23+7/8 / 24+15/16 / 26/27+1.1/16 / 29/30+1.3/16 / 31/32+1.1/4.

50370

Set contents 50360 … 50365 … 50370 …

10-part 10114-part 10115-part 101

50360 - 50370

METRINCH® combination wrenches

TypeOpen-end with 4-point wave profile, ring endwith 6-point wave profile, angled head 15° andring end 15°, short type, both ends mirror chromefinish.

QualityChrome-vanadium steel, 46 CrV4.

Note:Technical information see cat.-no. 50355.

50380

Size Length 50380 …mm + inch approx. mm

8 + 5/16 104 1019 + 11/32 116 10210 + 3/8 124 103

11 + 7/16 132 10412 + 15/32 136 105

13 + 1/2 147 106


14 + 9/16 168 10715 + 19/32 188 108

16 + 5/8 195 10917 + 11/16 206 11018 + 23/32 220 111

19 + 3/4 230 112


20/21 + 13/16 242 11322/23 + 7/8 260 11424 + 15/16 280 115

26/27 + 1.1/16 317 11629/30 + 1.3/16 367 117

31/32 + 1.1/4 384 118

50380

50360

50365

ß Hand tools


5

Adapter sets for combination ratchet wrenches

Type 4-part, contents: 1 adapter for bits 1/4inch (for size 10 mm), 1 adapter for socket wrench bits 1/4inch (for size 10mm), 1 adapter for socket wrench bits 3/8inch (forsize 13), 1 adapter for socket wrench bits 1/2inch(for size 19 mm). Quick-release socket wrenchadapter.

Application Used in conjunction with combination ratchetwrench (cat.-no. 50395, 50390 + 50391) for moun-ting bits and socket wrench bits.QualityChrome-vanadium steel.

50394


4-part 201

50394

Combination ratchet wrenches

0Type Straight, slim heads, chrome-plated, doublehexagonal, robust ratchet mechanism (72 teeth,ratcheting angle 5°).

Quality Chrome-vanadium steel.

50395


5-part 8 / 10 / 13 / 17 / 19 in roll bag 100


8 140 1019 149 102

10 159 10311 165 10412 171 10513 178 106


14 190 10715 199 10816 208 10917 225 11018 236 11119 248 112


21 291 11322 291 11424 333 11527 357 11630 402 11732 426 118

50395


0Type Reversible, ring end 15° offset, slim heads,chrome-plated, double hexagonal, robust ratchetmechanism (72 teeth, ratcheting angle 5°).


50390


5-part 8 / 10 / 13 / 17 / 19 in roll bag 100


8 140 1019 149 102

10 159 10311 165 104


12 171 10513 178 10614 190 10715 199 108


16 208 10917 225 11018 236 11119 248 112

50390


0Type With moving joint head, slim heads, chrome-pla-ted, double hexagonal, robust ratchet mechanism(72 teeth, ratcheting angle 5°).


50391


5-part 8 / 10 / 13 / 17 / 19 in roll bag 100


8 140 1019 149 102

10 159 10311 165 104


12 171 10513 178 10614 190 10715 199 108


16 208 10917 225 11018 236 11119 248 112

50391

eng/OP

• Combination wrenches • Ring wrenches

www.hhw.de50.16

5

Adapters for combination ratchet wrenches

0 Application Suitable for combination ratchet wrench straight(cat.-no. 50395), offset (cat.-no. 50390) and withjoint head (cat.-no. 50391).

50392

Adapter suitable for Adapter suitable for 50392 …Size inch size mm

1/4 10 101Bit 1/4 10 102

3/8 13 1031/2 19 104

50392


,Type Double hexagonal, with reverse ring. Easy reversalthanks to handy reverse button. Reverse ring with72 teeth. Slim version with 15° offset head, foreasy access in hart-to-reach places. 5° ratchetingangle. Dynamic-Drive profile. Angled head 15°.Polished, mirror-finished and nickel-polished,chrome-plated. In compliance with DIN and ISO.Quality Chrome-vanadium.

50396 101 50396 102

50397Set contents Packing 50396 …Size mm

6-part 8 / 10 / 12 / 13 / 14 / 17 clip holder 10112-part 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 clip holder 102

Size 50397 …mm

6 0997 1008 1019 102

10 103

Size 50397 …mm

11 10412 10513 10614 10715 108

Size 50397 …mm

16 10917 11018 11119 11222 113

Size 50397 …mm

24 11427 11530 11632 117

50396 - 50397

Combination flex head socket wrenches

NTypeSlim, chrome-plated, heads finely ground. Flexiblesocket head with UD profile. Hole for straight shaft(tommy bar).


Note: Straight shafts (tommy bars) see cat.-no. 50749 - 50750.

50400

Size Length Outside head Ø Straight Shaft (tommy bar) 50400 …mm approx. mm mm Borehole mm

10 179 4,7 / 15,5 5 10111 189 5,0 / 16,7 5 10212 198 5,5 / 18,0 5 10313 208 6,0 / 19,2 5 10414 218 6,3 / 20,5 6 105


15 231 6,7 / 21,7 6 10616 244 7,0 / 22,8 6 10717 255 7,5 / 24,2 8 10818 269 7,7 / 25,5 8 11019 283 8,0 / 26,7 8 109

50400

Ring wrenches (long)

TypeDouble-end, with AS-Drive profile, 15° offset,chrome-plated.

ApplicationThanks to the extremely thin-walled ring endsespecially suited for hard-to-reach places.

QualityHPQ high-performance steel.

50500

Size Length Ring end Ø Ring Thickness Height 50500 …mm mm mm mm

5,5 x 7 185 8,8 x 11,0 5,3 x 5,8 1016 x 8 205 9,8 x 12,1 5,6 x 6,0 102

9 x 11 250 14,2 x 16,7 8,0 x 8,7 10310 x 11 250 15,5 x 16,7 8,0 x 8,7 104

Size Length Ring end Ø Ring Thickness Height 50500 …mm mm mm mm

12 x 14 290 18,3 x 20,7 9,5 x 9,5 10513 x 14 290 18,7 x 20,7 9,5 x 9,5 10617 x 19 365 25,0 x 27,5 11,0 x 12,0 10718 x 19 365 25,5 x 27,5 11,0 x 12,0 108

50500

ß Hand tools


5

Straight ring wrenches DIN 837, ISO 10103

TypeDouble-end, with AS-Drive profile, extreme loadcapacity thanks to double-T profile. Chrome-platedon top of nickel. Anti-slip surface. Sets in cardboardbox.QualityChrome-alloy steel.

50502


7-part 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 10110-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 102


6 x 7 100 1018 x 9 115 102

10 x 11 130 10412 x 13 150 10513 x 17 170 107


14 x 15 165 10816 x 17 170 10917 x 19 185 11118 x 19 185 11219 x 22 210 114


20 x 22 210 11524 x 27 290 11730 x 32 325 119

50502 - 50503


NTypeThin-walled, polishing rings with UD profile.Chrome-plated. Set in cardboard box.



8-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 11112-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 25 x 28 / 30 x 32 112


6 x 7 98 2038 x 9 113 204

8 x 10 115 20510 x 11 130 20712 x 13 148 21113 x 15 160 213


13 x 17 168 21414 x 15 160 21514 x 17 170 21616 x 17 170 21718 x 19 185 21920 x 22 208 221


21 x 23 233 22222 x 24 233 22324 x 27 260 22530 x 32 320 228

50504 - 50505

Straight ring wrenches (inch)

,TypeImperial sizes. Thin-walled heads with 15° angle.Nickel and chrome-plated, mirror finish.

QualityVanadium-extra. 50506


1/4 x 5/16 156 1013/8 x 7/16 193 1021/2 x 9/16 220 103


19/32 x 11/16 258 1045/8 x 3/4 268 105

25/32 x 13/16 300 106


7/8 x 15/16 334 10715/16 x 1 352 1081 x 1.1/8 404 109

50506

eng/OP

• Ring wrenches

www.hhw.de50.18

5


,TypePolished, mirror-finished and nickel-polished,chrome-plated. Heads thin-walled, chamfered onboth sides, with Dynamic-Drive profile. Set inplastic pouch.QualityVanadium-extra.

50507


10-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 102


6 x 7 100 1018 x 9 115 102

10 x 11 130 10312 x 13 143 104


14 x 15 157 10716 x 17 168 10817 x 19 185 10918 x 19 189 110


20 x 22 200 11124 x 27 255 11230 x 32 285 113

50507 - 50509

Sets of straight ring wrenches DIN 837, ISO 10103

VTypeNew design, ergonomically shaped. Polished heads,chrome-plated, double hexagonal, in plastic clipholder.QualityChrome-vanadium steel.

50511



50511

Sets of offset ring wrenches DIN 838, ISO 10104

TypeOn both sides deeply offset, double hexagonal, ringends thin-walled and polished, chrome-plated. Incardboard box.QualityChrome-vanadium steel.

50510


8-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 10110-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 10312-part 6 x 7 / 8 x 9 / 10 x 11 / 10 x 13 / 12 x 13 / 14 x 15 / 16 x 17 / 17 x 19 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 104

50510


0TypeDouble-sided deeply offset, with Energy profile,chrome-plated, in cardboard box.QualityChrome-vanadium steel.

50512


8-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 09910-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 1009-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 101

12-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 26 / 25 x 28 / 30 x 32 10212-part 6 x 7 / 8 x 9 / 10 x 11 / 10 x 13 / 12 x 13 / 14 x 15 / 16 x 17 / 17 x 19 / 18 x 19 / 20 x 22 / 24 x 27 / 30 x 32 103

50512

ß Hand tools


5


NTypeOn both sides deeply offset. Thin-walled, polishedring end with UD profile, chrome-plated. In cardboard box.QualityVanadium 31CrV 3.

50513

Set contents 50513 …Size mm/inch


inch/ 8-part1/4 x 5/16 / 5/16 x 3/8 / 7/16 x 1/2 / 9/16 x 5/8 / 19/32 x 11/16 / 3/4 x 25/32 / 13/16 x 7/8 / 15/16 x 1 103

50513


VTypeOn both sides deeply offset, double hexagonal, ringends thin-walled and polished, chrome-plated.QualityChrome-vanadium steel.

50514 101


9-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 101in drawer plastic fitting 340 x 340 mm

12-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 26 / 25 x 28 / 27 x 32 204in cardboard box

50514


,TypeDeeply offset. Dynamic-Drive profile. Polished,mirror-finished and nickel-polished, chrome-plated.QualityVanadium-extra.

50515



50515


TypeDouble-sided deeply offset, with AS-Drive profile,extreme load capacity thanks to double-T profile.Chrome-plated on top of nickel. Anti-slip surface. Incardboard box.

QualityChrome-alloy steel. 50516


7-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 2019-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 24 203

50516

eng/OP

• Ring wrenches

www.hhw.de50.20

5

Offset ring wrench DIN 838, ISO 10104

TypeOn both sides deeply offset, double hexagonal, ringends thin-walled and polished, chrome-plated.QualityChrome-vanadium steel.

50517

50518

0TypeWith Energy profile.

50520NTypeWith UD profile.

50521

TypeWith AS-Drive profile.QualityChrome-alloy steel.

50522V 50520

50521

50518

50522

0 N VSW 50517 … 50518 … 50520 … 50521 … 50522 …mm

6 x 7 101 202 202 101 4028 x 9 103 203 203 103 403

8 x 10 104 204 204 40410 x 11 105 205 205 105 40510 x 13 106 206 206 10712 x 13 107 207 207 108 40712 x 14 108 208 20813 x 14 109 209 20913 x 15 110 210 210 41013 x 17 112 212 212 113 41214 x 15 113 213 213 114 41314 x 17 114 214 21416 x 17 115 215 215 116 41516 x 18 116 216 216 41617 x 19 117 217 217 118 41718 x 19 118 218 218 119 41818 x 21 21919 x 22 120 220 220 12119 x 24 121 221 22120 x 22 122 222 222 123 42221 x 23 123 224 224 124 42422 x 24 124 226 226 126 42624 x 26 125 227 227 127 42724 x 27 126 228 228 128 42824 x 30 22925 x 28 128 231 23127 x 30 23227 x 32 130 233 233 131 43330 x 32 131 234 234 132 43430 x 34 23530 x 36 23632 x 36 134 238 238 43836 x 41 240 240 135 44041 x 46 24146 x 50 242

50517 - 50522

Offset ring wrench DIN 838, ISO 10104 (inch)

NTypeImperial sizes. On both sides deeply offset.Thin-walled, polished ring end with UD profile, chrome-plated.


50525


1/4 x 5/16 170 1013/8 x 7/16 195 1021/2 x 9/16 225 104

19/32 x 11/16 245 105


5/8 x 11/16 245 1065/8 x 3/4 265 107

25/32 x 13/16 285 1083/4 x 7/8 285 109


13/16 x 7/8 285 11015/16 x 1 325 1121 x 1.1/8 345 113

1 .1/16 x 1.1/4 370 114

50525

50517

ß Hand tools


5

TORX® ring wrenches

VTypeChrome-plated, polished.ApplicationFor outer Torx® screws.QualityChrome-vanadium steel.

50526TypeDeeply offset.

50527TypeStraight.

50526

50527

offsetSize d Length 50526 …

E mm approx. mm4 x 5 3,86 x 4,75 165 1016 x 7 5,74 x 6,22 165 102

8 x 10 7,52 x 9,42 170 10311 x 12 10,08 x 11,17 190 10414 x 16 12,90 x 14,76 220 10518 x 20 16,70 x 18,45 255 10622 x 24 20,31 x 22,16 285 107

straightSize d Length 50527 …

E mm approx. mm6 x 8 5,47 x 7,52 113 101

10 x 12 9,42 x 11,17 140 10214 x 18 12,90 x 16,70 180 10320 x 24 18,45 x 22,16 224 104

50526 - 50527

TORX® ring wrenches

NType Straight, chrome-plated, ring ends polished. Application For outer Torx® screws.

Quality Vanadium 31CrV 3. 50536

Size d Length 50536 …E mm mm

6 x 8 5,74 x 7,52 110 10110 x 12 9,42 x 11,17 140 10214 x 18 12,90 x 16,70 180 103

50536

Double hexagonal ratchet ring wrenches

VTypeDouble hexagonal, mirror-finished and chromepolished. With Tractions profile.QualitySpecial steel.

50528TypeFlat, for clockwise and counterclockwise operatio-nand by turning over the wrench.

50529Type25° offset, reversible for clockwise and counter-clockwise operation.

50528

50529

flat 25° offsetSize Length 50528 … 50529 …mm approx. mm

6 x 7 110 1018 x 9 140 102 102

10 x 11 175 103 10312 x 13 175 104 104

flat 25° offsetSize Length 50528 … 50529 …mm approx. mm

14 x 15 205 105 10516 x 18 205 106 10617 x 19 205 107 10721 x 22 235 108 108

50528 - 50529


Type Straight, slim heads, mirror-finished and chromepolished, double hexagonal, robust ratchet mecha-nism (72 teeth, ratcheting angle 5°).


50530 20050530 201-206


6-part 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 18 / 17 x 19 synthetic leather bag 200


8 x 9 130 20110 x 11 150 20212 x 13 170 203


14 x 15 190 20416 x 18 210 20517 x 19 230 206

50530

eng/OP

• Ring wrenches

www.hhw.de50.22

5


JTypeChrome-plated and polished, in cardboard box.Reversible ratchet with double hexagonal ring end,5° ratcheting angle, therefore low space needed.

ApplicationThis wrench allows quick working, even when spaceis limited and turn movements are very narrow. Thewrenches are made for extreme applications.

50532 301

50532 401-407


4-part 10 x 11 / 12 x 13 / 16 x 18 / 17 x 19 301

Size 50532 …mm

6 x 7 4018 x 9 402

10 x 11 40312 x 13 40414 x 15 40516 x 18 40617 x 19 407

50532

Set of multi-purpose ratchets

OTypeWith exchangeable square socket wrench bits.Ratchet reversible for clockwise and counterclockwi-se operation. Socket wrench bit is locked with leverarm in centre position. In sheet metal case.

ApplicationFor working in hard-to-reach places.

50534

Square socket wrench bits 50534 …mm2,1 / 2,7 / 3 / 3,4 / 4,9 / 5,5 / 6,2 / 7 / 8 1013,4 / 4,9 / 5,5 / 6,2 / 7 / 8 / 9 / 11 102

50534

Multi-purpose ratchets

OTypeReversible for clockwise and counterclockwiseoperation, socket wrench bit is locked with lever armin centre position. Socket wrench bits not inclu-ded.

ApplicationFor exchangeable square socket wrench bits (cat.-no. 50538). For working in hard-to-reach places.

Note:Hexagon socket wrench bits available on request.

50535

Ø of For square Lever arm length up to 50535 …Size sockets mm mm centre of the borehole mm

00 16 2,1 - 8,0 115 2010 22 3,4 - 11,0 155 2021 29 4,9 - 14,5 175 2032 36 10,0 - 18,0 220 2043 45 14,0 - 22,0 300 2054 60 18,0 - 30,0 380 206

50535

Square socket wrench bits for multi-purpose ratchets

OApplicationFor multi-purpose ratchets cat.-no.50535.

Note:Other socket wrench bits, hexagonal or specialshapes, available on request.

50538

for Square 50538 …Size mm

00 2,7 20300 3,4 20500 4,9 20900 6,2 21200 8,0 2140 4,9 2190 5,5 2210 6,2 2220 9,0 225


0 10,0 2261 5,5 2301 6,2 2311 7,0 2321 8,0 2331 9,0 2341 10,0 2351 11,0 2361 12,0 237


1 13,0 2381 14,0 2392 10,0 2402 11,0 2412 12,0 2422 13,0 2432 14,0 2442 14,5 2452 16,0 246


2 17,0 2473 16,0 2513 17,0 2523 18,0 2533 19,0 2543 22,0 2564 20,0 2594 24,0 261

50538

ß Hand tools


5

Set of ratchet ring wrenches

Type19-part, reversible ratchet ring wrenches. Thedifferent inserts can be taken up directly with theratchet wrench.


50540


19-part 101

50540

Set contentsA 1 reversible ratchet ring wrench, double hexagonal, size 14 / 19 mm,N 9 inserts hexagonal, size 8 / 9 / 10 / 11 / 12 / 13 / 15 / 16 / / 17 mm,4 9 inserts for outer Torx® screws, E 8 / 10 / 11 / 12 / 14 / 16 / 18 / 20 / 22.

4 in 1 reversible ratchet ring wrenches

TypeDouble hexagon, reversible.


50541

Size 50541 …mm

8 x 10 / 12 x 13 20110 x 13 / 17 x 19 20214 x 17 / 18 x 19 203

50541

Free wheel ratchets and socket wrenches

N50543Free wheel ratchetsTypeWith built-in ball catch for safe mounting of thesocket wrenches. Counterclockwise and clockwiseoperation by simply turning over the ratchet, the toolworks without teeth and free gear. Socket wrenchbits not included.QualityVanadium 31 CrV 3, burnished.

50545Socket wrenchesTypeExchangeable socket wrench bits with UD profileand groove for ball catch.QualityVanadium 31 CrV 3, ground.

50543

RatchetSize Length 50543 …mm approx. mm

14 - 17 205 10218 - 23 255 10324 - 28 305 10430 - 32 400 105

PointSize 50545 …mm

14 10715 10816 10917 11018 111

Size 50545 …mm

19 11221 11322 11423 11524 116

Size 50545 …mm

26 11727 11828 11930 12032 121

50543 - 50545


Digital slide callipers by ATORN:

ATORN‘s high-quality measuring tools.

eng/OP

• Ratchet wrenches • Joint Socket wrenches • Ring wrenches

www.hhw.de50.24

5

Double hexagonal flex-head socket wrenches

VTypeChrome-plated, rings polished, both sides swivel90°.


Note:Size 6 x 7 mm with hexagon heads.

50550


6 x 7 162,7 1018 x 9 179,4 102

10 x 11 198,5 10312 x 13 214,4 10514 x 15 232,0 109


16 x 17 243,2 11117 x 19 259,1 11318 x 19 260,0 11421 x 22 277,0 116

50550

Heavy-duty double hexagonal drive ring wrenches

NTypeDeeply offset, chrome-plated, rings polished,spring-loaded locking pin for extension bars (cat.-no.50566) at the end of the wrench.

ApplicationFor heavy-duty applications.QualityVanadium 31CrV 3.

50565

Size Length Head height Outer ring 50565 …mm approx. mm mm Ø mm

24 180 16,0 38 20127 190 17,0 42 20230 200 18,0 46 20332 235 19,0 52 20434 235 19,0 52 20536 245 20,0 58 20641 265 22,0 62 20846 280 24,0 69 20950 290 25,5 76 210

Size Length Head height Outer ring 50565 …mm approx. mm mm Ø mm

55 300 28,0 82 21160 345 30,5 90 21265 355 33,0 98 21370 365 35,5 106 21475 375 38,0 114 21580 385 40,0 122 21685 385 40,0 130 21790 410 45,0 142 21895 410 45,0 142 219

50565

Extension pipes for drive ring wrenches

NQualityTubular steel, chrome-plated.

50566

For size Length Inner pipe Ø 50566 …mm approx. mm mm

24 - 30 460 19 20132 - 41 610 22 202

For size Length Inner pipe Ø 50566 …mm approx. mm mm

46 - 55 760 25 20360 - 95 860 30 204

50566

Ratchet wrenches

ApplicationMainly for union nuts on piping. One wrench for bothmetric and imperial size nuts and bolts.Quality

Stainless, tempered steel. 50547 101

50547 102-111Set contents 50547 …Size mm

5-part 10 / 11 / 14 / 17 / 19 101

Size Size 50547 …mm inch

8 5/16 10210 3/8 10311 7/16 10412 15/32 10513 1/2 106

Size Size 50547 …mm inch

14 9/16 10716 5/8 10817 21/32 10918 11/16 11019 3/4 111

50547

ß Hand tools


5

Engine block wrenches

NTypeThin-walled, polished ring end with UD profile,chrome-plated.ApplicationFor work on engine blocks.


Size Length Head thickness Outer ring Ø 50568 …mm approx. mm mm mm

11 x 13 150 7,0/8,5 17,0/20,5 10114 x 16 185 8,7/10,3 21,5/24,5 10215 x 17 185 8,7/10,3 23,0/25,5 103

Size Length Head thickness Outer ring Ø 50568 …mm approx. mm mm mm

16 x 18 185 8,7/10,3 24,5/27,0 10419 x 22 230 10,0/11,5 28,0/32,5 105

50568

Striking-face ring wrenches DIN 7444

NTypeWith UD profile.ApplicationFor heavy-duty applications.

QualityTempering steel.

Note:Starting at size 65 mm as standard double hexago-nal.

50570

Size Length Head height Outer ring Ø 50570 …mm approx. mm mm mm

27 180 15,5 47 10130 190 16,5 52,5 10232 195 16,5 54 10334 195 16,5 54 10436 205 19,5 60 10541 225 20,5 66 10646 240 22,5 75 10750 250 23,5 80 109

Size Length Head height Outer ring Ø 50570 …mm approx. mm mm mm

55 270 25,0 87,5 11060 270 26,0 93,5 11165 290 29,0 101 11270 320 32,5 109,5 11375 325 34,0 115 11480 345 35,0 123 11585 360 37,0 130 116

50570

Striking-face (slogging) ring wrenches

TypeDouble hexagonal, forged, thin-walled, greenlacquered. Rings are thinner than standard rings,therefore the wrenches are suitable for work in hard-

to-reach places. Rings are higher than standard nut,therefore the wrenches do not seize.ApplicationFor heavy-duty applications.QualityChrome-alloy steel.

50574

Size Length Head height Outer ring Ø 50574 …mm mm mm mm

32 195 24 47 10136 195 26 52,4 10241 200 29 59 10346 250 32 65 10450 280 35 70 10555 300 38 76 10660 300 42 82,5 10865 325 45 90,5 10970 355 48 97 11075 360 51 103,5 111

Size Length Head height Outer ring Ø 50574 …mm mm mm mm

80 440 57 110 11285 440 57 117 11390 445 60 124 11495 450 67 131 115

100 455 72 137 116105 460 73 146 117110 500 82 156 118115 505 82 162 119120 510 82 174 120

50574

Union nut (split-ring) wrenches DIN 3118

NTypeOpen ring wrench with UD profile, chrome-plated.Heads offset 15°, with reinforced connectionbetween ring end and handle. Opening offset 15°.ApplicationFor union nuts on piping.


Note:50582 101 - 104 with hexagon. Opening offset 30°.

50582

Size Length Height of ring Outer ring Ø 50582 …mm approx. mm mm mm

8 x 10 140 6,5/8,0 18/20 10110 x 11 150 8,0/8,5 20/22 10211 x 13 160 8,5/10,5 22/26 10312 x 14 170 9,5/11,5 24/28 10413 x 15 180 10,5/11,8 26/29 10514 x 17 195 11,5/12,2 28/32 106

Size Length Height of ring Outer ring Ø 50582 …mm approx. mm mm mm

17 x 19 210 12,2/13,2 32/35 10719 x 22 230 13,2/15,2 35/41 10822 x 24 250 15,2/16,2 41/45 10924 x 27 270 16,2/17,2 45/48 11030 x 32 300 20,2/22,2 50/52 111

50582

eng/OP

• Hook wrenches • Face wrenches

www.hhw.de50.26

5

Hook wrench DIN 1810 A

mTypeWith hook.ApplicationFor slotted nuts DIN 1804 and roller bearing nutsDIN 981.

QualitySpecial steel, hardened, burnished. 50650

For nut Overall length Thickness of Material 50650 …outside Ø mm mm mm

12 - 14 110 3 10116 - 20 110 3 10225 - 28 136 4 10330 - 32 136 4 10434 - 36 170 5 10538 - 45 170 5 12740 - 42 170 5 10645 - 50 206 6 10752 - 55 206 6 10858 - 62 240 7 109

For nut Overall length Thickness of Material 50650 …outside Ø mm mm mm

65 - 70 240 7 12868 - 75 240 7 11080 - 90 280 8 11185 - 92 280 8 129

95 - 100 280 8 11298 - 105 290 8 130

110 - 115 335 10 113120 - 130 335 10 114135 - 145 385 10 115155 - 165 385 10 116

50650

Hook wrench DIN 1810 B

mTypeWith pilot. ApplicationFor capstan nuts DIN 1816.


For nuts Pilot Ø Overall Material 50653 …Outside Ø mm mm length mm thickness mm

12 - 14 2,0 110 3 10116 - 18 2,5 110 3 10220 - 22 2,5 110 3 10325 - 28 3,0 136 4 10430 - 32 4,0 136 4 10534 - 36 4,0 170 5 10640 - 42 4,0 170 5 10745 - 50 5,0 206 6 10852 - 55 5,0 206 6 109

For nuts Pilot Ø Overall Material 50653 …Outside Ø mm mm length mm thickness mm

58 - 62 5,0 240 7 11068 - 75 6,0 240 7 11180 - 90 6,0 280 8 112

95 - 100 8,0 280 8 113110 - 115 8,0 335 8 114120 - 130 8,0 335 8 115135 - 145 8,0 380 8 116155 - 165 8,0 380 8 117

50653

Adjustable hook wrench

mTypeWith hook and gear teeth.ApplicationFor slotted nuts DIN 1804 and roller bearing nutsDIN 981.

QualitySpecial steel, ground, hardened, burnished. 50656

For nut outside Ø Overall length Thickness of Material 50656 …mm mm mm

20 - 42 180 4 10145 - 90 240 6 102

95 - 165 335 10 103

50656

ß Hand tools


5

Hook wrench with joint

mTypeWith hook and attachment eye.ApplicationFor slotted nuts DIN 1804 and roller bearing nutsDIN 981.



20 - 35 165 4 10135 - 60 210 5 10260 - 90 280 6 103


90 - 155 335 7 104155 - 230 460 8 105

50659

Hook wrench with joint

mTypeWith fixed pilot and attachment eye. Hook and pilotmade of one piece.ApplicationFor capstan nuts DIN 1816.


For nut outside Ø Overall length Pilot nominal Ø 50662 …mm mm mm

22 - 35 165 3,0 10235 - 60 205 4,0 10460 - 90 280 5,5 106

For nut outside Ø Overall length Pilot nominal Ø 50662 …mm mm mm

95 - 155 335 6,0 108165 - 230 460 10,0 110

50662

Hinged face wrenches

mTypeWith electrically welded-on pilot and attachment eye.ApplicationFor two-hole nuts.

QualitySpecial steel, burnished. 50665

Pilot Nominal Length Material 50665 …spacing mm mm mm Thickness mm

18 - 40 3 150 5 10118 - 40 4 150 5 10240 - 80 4 220 6 10340 - 80 6 220 6 105

Pilot Nominal Length Material 50665 …spacing mm mm mm Thickness mm

80 - 125 6 295 8 10680 - 125 8 295 8 108

125 - 200 8 405 10 109125 - 200 10 405 10 110

50665

Adjustable face wrenches

mTypeWith riveted steel pilot, and, above size 11 - 60 mmwith electrically welded-on pilot.ApplicationFor two-hole nuts.

QualitySpecial steel, burnished. 50668

Pilot Overall length Pilot nominal Ø 50668 …spacing mm mm mm

7 - 40 115 1,5 1017 - 40 115 2,0 1027 - 40 115 2,5 103

11 - 60 160 3,0 10411 - 60 160 4,0 105

Pilot Overall length Pilot nominal Ø 50668 …spacing mm mm mm

11 - 60 160 5,0 10614 - 100 215 5,0 10714 - 100 215 6,0 10822 - 125 260 8,0 11022 - 125 260 10,0 111

50668

eng/OP

• Socket wrenches • Wrenches for switch cabinets

www.hhw.de50.28

5

Square wrench DIN 904/905

QualitySpecial steel, hardened and burnished.

50700

50701

7 Outer square wrench DIN 904Size Shank length x Ø 50700 …mm mm

4 50 x 8 2015 60 x 12 2026 80 x 12 2037 80 x 16 2048 80 x 16 2059 85 x 17 206

10 100 x 20 20712 100 x 24 20813 100 x 24 20914 120 x 28 21017 160 x 33 21119 200 x 35 21222 200 x 40 213

P Inner square wrench DIN 905Size Shank length x Ø 50701 …mm mm

4 55 x 8 2015 60 x 12 2026 80 x 12 2037 80 x 12 2048 80 x 16 2059 80 x 16 206

10 100 x 20 20711 100 x 20 20812 100 x 24 20913 100 x 24 21014 120 x 28 21117 160 x 34 21219 200 x 36 213

50700 - 50701

Inner triangular wrenches DIN 22417

TypeHot forged, tempered, galvanised, with sliding T-handle.ApplicationFor triangular screws DIN 22424 and triangular nutsDIN 22425.

QualitySeamless precision tubular steel.

50704

For triangular Wrench length Handle length x Ø 50704 …screws mm mm

M 4 90 50 x 4 101M 5 100 63 x 5 102M 6 112 80 x 6 103

For triangular Wrench length Handle length x Ø 50704 …screws mm mm

M 8 125 100 x 6 104M 10 140 125 x 8 105M 12 160 160 x 10 106

50704

Multi-purpose wrenches for electrical cabinets

62325 201 Type Functions: 1-2. inner square wrench 6, 7-8 mm, 3. inner triangular wrench 8 mm, 4. warded key 3-5 mm, 5. double bit on chain slotted screws 1 x 7 mm +

Phillips PH2, 6. plastic adapter 1/4 inch.

62325 202 Type Functions: 1. outer square 4-10 mm, 2-4. inner square wrench 5, 7, 8 mm,5. inner triangular wrench 8 mm, 6. double bit on chain slotted screws 1 x 7 mm +

Phillips PH2, 7. plastic adapter 1/4 inch.

62325 203 Type Functions: 1. inner square wrench 6, 7-8 mm, 3. inner triangular wrench 9 mm, 4. warded key 3-5 mm, 5. double bit on chain slotted screws 1 x 7 mm +

Phillips PH2, 6. plastic adapter 1/4inch.

62325 205Multi-purpose wrench for switch cabinets, screwdri-ver, and contactless, single-pole voltage tester. Forall standard switch cabinets. Thanks to the multi-purpose 1/4inch bit mount, all standard bits can beinserted. A neodymium permanent magnet securesthe bits. With shirt clip.Functions:1-2. inner square wrench 6, 7-8 mm,3. inner triangular wrench 9 mm,4. double-sided key 3-5 mm,5. bit Phillips PH2,6. plastic adapter for 1/4inch bits,7. bleeding wrench 5 mm.

62325 206For almost all locks in gas and water supply, aircondition and ventilation, inspection lids, streetlights, rubbish bins, rubbish containers, etc.Functions:1-4. inner square wrench 5, 6, 7-8, 9-10 mm,5-7. inner triangular wrench 7, 8-9, 10-11 mm,8. warded key 3-5 mm,9. half moon 6 mm.

62325 201 62325 202

62325 203

Size Weight 62325 …mm g

72 x 72 70,5 20190 x 60 79,0 20245 x 45 50,0 203

158 x 28 135,0 20596 x 92 204,0 206

62325

62325 205

62325 206

ß Hand tools


5

Hexagonal wrenches DIN 896 B

TypeDouble-end, tempered.QualityHardened, chrome-plated.

50707TypeSet with stepped straight shaft (tommy bar).



Size Length Straight Shaft (tommy bar) Borehole 50708 …mm approx. mm mm

6 x 7 110 5,3 3018 x 9 110 6,3 302

8 x 10 120 6,3 30310 x 11 120 6,3 30410 x 13 140 6,3 32812 x 13 140 8,5 30514 x 15 140 8,5 30614 x 17 150 10,5 30716 x 17 150 10,5 30817 x 19 160 12,5 31018 x 19 160 12,5 311

Size Length Straight Shaft (tommy bar) Borehole 50708 …mm approx. mm mm

19 x 22 170 12,5 31320 x 22 170 12,5 31421 x 23 170 14,5 31522 x 24 190 14,5 31724 x 26 190 14,5 31824 x 27 190 14,5 31925 x 28 200 16,5 32027 x 30 200 16,5 32130 x 32 200 16,5 32232 x 36 220 18,5 32436 x 41 220 18,5 325

50707 - 50708

Solid hexagonal wrenches DIN 896 A, ISO 2236/1085

TypeTitacrom chrome-plated, with hexagon shank forattaching open-end wrenches. Straight shaft (tommybar) borehole, through hole. QualityChrome-vanadium steel.

50738TypeSet with 1 ea. stepped straight shaft (tommy bar) forsize 6 - 15 mm and 16 - 32 mm. In cardboard box.

50739


12-part 6 x 7 / 8 x 9 / 10 x 11 / 12 x 13 / 14 x 15 / 16 x 17 / 18 x 19 / 20 x 22 / 21 x 23 / 24 x 27 / 25 x 28 / 30 x 32 115


6 x 7 105 10 / 11 4 2018 x 9 110 13 / 14 4 202

10 x 11 120 15 / 16 5 20312 x 13 140 18 / 19 5,5 20414 x 15 145 20 / 22 6 20716 x 17 155 23 / 24 7 209


18 x 19 165 25 / 26 8 21120 x 22 170 28 / 30 9 21321 x 23 185 29 / 31 10 21424 x 27 190 33 / 35 12 21725 x 28 205 34 / 37 12 21830 x 32 210 40 / 42 14 219

50738 - 50739

Straight shafts (tommy bars) for socket wrenches

TypeSolid, straight shaft.QualityHardened, galvanised.

50749

50750 101

not stepped DIN 900Ø Length 50749 …

mm approx. mm5 125 2016 160 2028 180 203

10 200 20412 250 20514 320 20616 400 20718 500 208

stepped steppedØ Length 50750 …

mm approx. mm5 / 6 / 8 / 10 / 12 180 101

5 / 6 / 8 / 10 / 12 / 14 / 16 245 102

50749 - 50750

50708

50707 101 50707 102

50750 102

eng/OP

• Socket wrenches • Cross wrenches • Tyre levers • Tyre levers

www.hhw.de50.30

5

Heavy-duty offset socket wrenches ISO 2236

TypeHexagon, special borehole allows plug-throughof bolts or straight shafts (tommy bars).Hollowbody and pre-drilled socket head for overlappingand also very long bolts. Chrome-plated, polished.QualityChrome-vanadium steel.

50760


6 102 1017 106 1028 114 1039 122 104

10 129 10511 136 10612 144 10713 152 108


14 160 10915 169 11016 178 11117 187 11218 195 11319 204 11421 221 11622 230 117


24 250 11927 280 12230 310 12532 330 12734 350 12936 370 131

50760

Heavy-duty offset socket wrenches

NTypeWith solid head and large head depth for protrudingbolts, chrome-plated.QualityVanadium 31CrV 3.

50761 50762

SquareSize Length 50761 …mm mm

8 150 10310 175 10512 215 10713 230 10814 240 10917 280 110

HexagonSize Length 50762 …mm mm

10 160 20113 200 20314 215 20416 240 20617 250 20718 265 20819 280 20921 305 211

HexagonSize Length 50762 …mm mm

22 315 21224 345 21427 380 21730 420 22032 450 22236 500 22641 560 231

50761 - 50762

Spider wrenches DIN 3119

50765 201NTypeWith reinforced centre section for protection, silver.ApplicationFor car wheel nuts in metric and imperial sizes.QualityVanadium 31CrV3.

50765 202NTypeWith 3/4 inch square, for socket wrench bits, silver.ApplicationFor trucks, agricultural equipment, tractors andindustrial applications.QualityVanadium 31CrV3.50766

VTypeWith 1/2 inch square, for socket wrench bits.Chrome-plated, ground heads, heads and centrepiece forged, heads and lever arms hardened (up to500 Nm), long lever arms.ApplicationFor cars, light-duty commercial vehicles andconstruction site equipment.QualityChrome-vanadium steel.

50766

50765

N VWrench size Length 50765 … 50766 …

mm mm17 x 19 (3/4inch) x 21 x 11/16inch 420 201

24 x 27 x 32 x 3/4inch 750 20217 x 19 x 22 x 1/2inch square 420 201

50765 - 50766

ß Hand tools


5

Tyre levers

50769 102-108VQuality Chrome-vanadium steel.

50769 102 Double T profile, chrome-plated. For cars and light-duty commercial vehicles.

50769 107 Silver-grey. Especially suitable for tubeless tyres.

50769 108 Silver-grey. Heavy-duty version for commercial vehicles.

50769 203-206Type Double-T profile, chrome-plated, profiled, drop-for-ged. QualityChrome-vanadium steel.

50769 102

50769 107

50769 108

VOverall length 50769 … 50769 …

approx. mm200 102300 203400 204460 107500 205600 108 206

50769

50769 203-206

Tyre levers

TypeDouble-T profile for good stability. With screwed-on,exchangeable plastic cover.

ApplicationFor mounting and removing of tyres from steel rimsand especially aluminium rims.QualityChrome-vanadium steel.

50770

Length 50770 …mm500 104

50770

Tyre levers

bType Chrome-plated. Application For removing the cylinder head, loosening of seized-up parts, ejecting and dejecting of bearings and

bearing seats, assembling and disassemblingsprings, bolts, gear wheels etc. QualityChrome-vanadium.

50772 201

50772 202

50772 203

Overall length 50772 …mm400 201400 202600 203

50772

Set of tyre levers

bType4-part, chrome-plated. 1 ea. 200/ 300/ 450/ 600mm. With strong 2-component handle for safe gripand comfort. With attachment eye.


50774

Set contents Length 50774 …mm

4-part 200 / 300 / 450 / 600 101

50774

Tyre levers

bTypeWith angled blade and handle.

50773

Length 50773 …mm400 101500 102600 103800 104

50773

eng/OP

• Socket wrenches

www.hhw.de50.32

5

Set of socket wrenches

BType20-part, in sheet steel box 230 x 130 x 56 mm. Theexchangeable blade system Smart-Griff doubles asscrewdriver and T-handle. Socket wrench with M-Tecfunction: a spring-loaded magnet secures the screwor nut and makes it possible to work even in hard-to-reach places. When the threads are long, themagnet retreats, so thateven long stud bolts can be accommodated in thelarge socket wrench tube.QualityChrome-vanadium steel.

50775


20-part 201

50775

Hexagonal socket wrenches DIN 3125

ßTypeLong, chrome-plated, inner hexagon, large socketdepth for projecting bolts, with impact-proof plastichandle. Blade length 125 mm.


Size 50787 …mm

3 1013,5 102

4 1034,5 104

5 1055,5 106

Size 50787 …mm

6 1077 1088 1099 110

10 11111 112

Size 50787 …mm

12 11313 11414 11515 11616 11717 118

50787

Hexagonal socket wrenches with flexible shank

ßTypeLong type, with flexible shaft, large socket depth.Shaft stands a torque value of 12 Nm in bothdirections. Shaft length 100 mm.

ApplicationFor worm threads, hose clamps and projecting bolts.QualityChrome-vanadium steel.

50788

Size Overall length 50788 …mm mm

6 255 1017 255 1028 255 103

50788

Set of hexagonal socket wrenches

sTypeRound blade with hollow shank, nicromatt Multi-component Kraftform handle with roll stop..ApplicationFor outer hexagon screws in accordance with DIN475/2. Suitable for all screw connections withthreaded bars thanks to the hollow shank.

50795


7-part 5 x 70 / 5,5 x 70 / 6 x 70 / 7 x 80 / 8 x 80 / 10 x 80 / 13 x 80 101

50795

Set contentsN 7 socket wrenches E 6,3 x 155 mm, size 5,5 / 6 / 7 / 8 / 10 / 13 / 17 mm,

1 bit holder 1/4 inch x 58 mm, 1 bit holder 1/4 inch x 155 mm,D 2 bits for Phillips recess head screws C 6,3 x 25 mm, PH 1 / 2,E 2 bits for Phillips recess head screws C 6,3 x 25 mm, PZ 1 / 2,Q 2 bits for slotted screws C 6,3 x 25 mm, 3,5 x 0,6 / 5,0 x 0,8 mm,M 4 bits for Torx® screws C 6,3 x 25 mm, TX 15 / 20 / 25 / 30,

1 handle 105 x 39 mm.

ß Hand tools


5

Hexagonal socket wrench

ApplicationEspecially suitable for hat nuts and nuts on longbolts or threaded bars as well as for working in hard-to-reach places.

50800ßTypeInner hole for projecting threaded shanks, redplastic handle made of PP.QualityBlade made of C 35.

50802

+TypeDIN 60900.VDE 0682/Part 201, IEC 900, routine-tested. Bladehardened throughout, burnished. Inner hole forprojecting thread bars. Blade insulation sprayeddirectly on the blade.QualityBlade chrome-vanadium steel.

50800

50802

ß +Size 50800 … 50802 …mm4,0 3034,5 2045,0 205 3055,5 206 3066,0 207 307

ß +Size 50800 … 50802 …mm7,0 209 3098,0 211 3119,0 212 312

10,0 213 31311,0 214 314

ß +Size 50800 … 50802 …mm12,0 215 31513,0 216 31614,0 217 31717,0 220 320

50800 - 50802

Hexagonal socket wrench

ßTypeWith T-handle made of impact-proof, black plastics.Hardened, nickel-plated, inner hole for projectingscrews.

QualityChrome-vanadium steel. 50807 203-212

50807 215-220

Size Blade length 50807 …mm mm

7 125 2038 125 204

10 125 20511 125 20612 125 20713 125 20814 125 20915 125 21016 125 21117 125 212

long typeSize Blade length 50807 …mm mmL 8 350 215

L 10 350 216L 11 350 217L 12 350 218L 13 350 219L 14 350 220

50807

www.atorn.com


Screwdrivers by ATORN:




www.atorn.com


Documents

Hand tools - katalog.hhw.dekatalog.hhw.de/EN/50_HHW_Katalog_2010_eng.pdf · ß Hand tools eng/OP 50.3 5 The new generation of wrenches Adjustable wrenches DIN 3117 Open-end, ring