Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
© 2018 Eaton. All Rights Reserved..
HALO COMMERCIAL HC4 Series Training Guide 4” LED Downlights
November 2018
2 © 2018 Eaton. All Rights Reserved..
3-PART ORDERING STRUCTURE
1. Housing Frame
a. Lumens (lumen selection specifies driver)
b. 1000-1500-2000-3000-4000 lm
2. LED Module – low or high lumen (per frame selected)
a. Low lumen 1000-1500-2000 lm
b. High lumen 3000-4000 lm
c. 80 or 90 CRI and 2700K, 3000K, 3500K, or 4000K
3. Reflector
a. Beam: Narrow – Medium – Wide, or Wall Wash
b. Finish: Specular Clear, Semi-Specular Haze, White, White Baffle, Black Baffle
2
Housing Frame Light module Reflector
Complete HC4
Halo Commercial HC4 – System View
4-inch LED Downlights
3 © 2018 Eaton. All Rights Reserved..
Halo Commercial HC4
4-inch LED Downlights
Nominal values for 15 - 20 footcandles at nadir
4 © 2018 Eaton. All Rights Reserved..
4
Halo Commercial HC4 – Feature Specs
4-inch LED Downlights – Housing Frame
1. Housing Frame
a. Boat-shaped galvanized steel
b. New construction or remodeling installation
c. Plaster lip pre-set 1/2“, adjusts for ceilings up to 1-1/2" thick
2. No Fuss Bar Hangers™
a. Pre-installed and centered mounting bars
b. Bars lock to tee grid with screwdriver or pliers
c. Centering marks on the bar bracket
3. Adjustable Mounting Brackets
a. Bar brackets adjust 2" vertically from above the ceiling or through the aperture
b. Brackets for use with the included “No Fuss” mounting bars or with 1/2" EMT
c. Brackets remove for remodel install from below the ceiling
4. Junction box
a. Listed for (8) #12 AWG 90° C conductors (4-in/4-out)
b. Listed for feed through branch wiring
c. (3) 1/2" and (2) 3/4" trade size pry-outs
d. Low voltage barrier section for 0-10V dimming wires
e. (3) 4-port push wire nuts (1-port is fixture connection)
1
2 3
4
HC4 Frame
1
2
5 © 2018 Eaton. All Rights Reserved..
5
Halo Commercial HC4 – Feature Specs
4-inch LED Downlights – LED Driver (Frame)
5. LED Driver – Pre-installed on housing frame
a. 120V-277V, Universal voltage, 50/60Hz
b. Dimmable 0-10V analog 1% dimming control standard
a. “D010” designates this standard driver
c. Fixed lumen output
i. Lumens are selected when ordering the frame
ii. 1000 lm and 1500 lm luminaires are IC and Non-IC
iii. 10 = 1000 lm (IC and Non-IC rated)
iv. 15 = 1500 lm (IC and Non-IC rated)
v. 20 = 2000 lm (Non-IC rated)
vi. 30 = 3000 lm (Non-IC rated)
vii. 40 = 4000 lm (Non-IC rated)
d. Example frame model number
i. HC415D010 =
i. 4-inch frame with 1500 lumen driver
HC4 Driver
5
6 © 2018 Eaton. All Rights Reserved..
6
Halo Commercial HC4 – Feature Specs
4-inch LED Downlights – LED Module
6. LED Module – HM4 ordered separately
a. Low or high lumen module
i. Select per the lumen value of the frame (driver)
ii. HM412 = Low lumen 1000-1500-2000 lm
iii. HM434 = High lumen 3000-4000 lm
b. Color Rendering Index
i. 8 = 80 CRI
ii. 9 = 90 CRI
c. Correlated Color Temperature
i. 27 = 2700K
ii. 30 = 3000K
iii. 35 = 3500K
iv. 40 = 4000K
d. Example LED module model number
i. HM412835 =
i. 4-inch LED module for 1000, 1500, or 2000 lm frame, 80 CRI, 3500K
6
HM4 High
Lumen LED
Module
HM4 Low
Lumen LED
Module
7 © 2018 Eaton. All Rights Reserved..
7
Halo Commercial HC4 – Feature Specs
4-inch LED Downlights - Reflectors
7. Reflectors – 41 series
a. Self-flanged, spun aluminum, downlight & wall wash
i. C = Specular Clear, polished flange
ii. H= Semi-Specular Haze, polished flange
iii. W = Matte White, white flange
iv. BB = Black Baffle, white flange
v. WB = White Baffle, white flange
vi. “WF” white flange option: Specular, Semi-Specular
b. Beam distribution
i. Reflector options: Narrow, Medium, Wide
ii. Rotatable lensed wall wash (RWW)
i. Exclusive rotatable insert w/ linear spread lens
c. Non-conductive matte white polymer reflector
i. May be used to meet codes and specifications for “dead front” trim
7
Beam Distribution*
Code Distribution Spacing
Criteria
Beam
Angle
ND Narrow 0.76 45°
MD Medium 1.0 55°
WD Wide 1.2 65°
x = ND, MD, WD beam distribution
41xBB
Black Baffle
41RWWH
Haze Wall Wash
41PSMDW
White Polymer
(Dead Front)
41xH
Semi-Specular
(Haze)
41xC
Specular Clear
41xWB
White Baffle
41xW
White
*Nominal Values
8 © 2018 Eaton. All Rights Reserved..
8. Emergency backup - factory installed
a. Use with standard “D010” 0-10V dimming driver
b. Remote emergency battery backup 7W or 14W, remote test switch
c. Integral emergency battery backup 7W or 14W, integral test switch
9. DLVP distributed low voltage power system – factory installed
a. “DLV” low voltage dimming driver (“DLV” replaces “D010” driver)
b. Remote & integral emergency options available in DLV
c. 300W or 600W low voltage power supply (order separately)
d. Low voltage plenum rated pre-terminated cables (order separately)
10. Connected lighting - factory installed
a. Use with standard “D010” 0-10V dimming driver
b. LumaWatt Pro: “LWPD1” controller, tile mount wireless sensor
c. WaveLinx: “SWPD1” relay w/ 0-10V dimming, tile mount wireless sensor
8
Halo Commercial HC4 – Factory Installed Options
4-inch LED Downlights – EM & Connected Lighting
10b
LumaWatt Pro
control & sensor WaveLinx relay &
sensor
10c
8
9
DLVP
Saves up to 40%
9 © 2018 Eaton. All Rights Reserved..
9
Halo Commercial HC4
4-inch LED Downlights – Dimensions
Reflector Max.
Height
Trim
Height
LED
Height
Narrow 3.97” 2.48” 3.48”
Medium 4.06” 2.57” 3.57”
Wide 3.87” 2.39” 3.39”
Baffle 3.87” 2.39” 3.39”
LOW LUMEN
1000lm, 1500, 2000lm
10 © 2018 Eaton. All Rights Reserved..
10
Halo Commercial HC4
4-inch LED Downlights – Dimensions
Reflector Max.
Height
Trim
Height
LED
Height
Narrow 6.27” 2.48” 3.48”
Medium 6.36” 2.57” 3.57”
Wide 6.17” 2.39” 3.39”
Baffle 6.17” 2.39” 3.39”
HIGH LUMEN
3000lm, 4000lm
11 © 2018 Eaton. All Rights Reserved..
Halo Commercial HC4
4-inch LED Downlights
12 © 2018 Eaton. All Rights Reserved..
12
Halo Commercial HCR4 – Feature Specs
4-inch LED Retrofit Downlights – Frame/Collar
1. Frame/collar HC4R
a. Galvanized steel
b. Retrofits existing open frame 4-3/4” to 4-7/8” apertures
c. Collar 2" thick
2. Butterfly spring clips - 2
a. Pre-installed
3. Junction box
a. Listed for (8) #12 AWG 90° C conductors (4-in/4-out)
b. Listed for through-branch wiring
c. (3) 1/2" and (2) 3/4" trade size pryouts
d. Low voltage barrier section for 0-10V dimming wires
e. (3) 4-port push wire nuts (1-port is fixture connection) 1
2
3
HC4R Frame/Collar
13 © 2018 Eaton. All Rights Reserved..
13
Halo Commercial HCR4 – Feature Specs
4-inch LED Retrofit Downlights – LED Driver
4. LED Driver – pre-installed on junction box with whip for LED module connection
a. 120V-277V, Universal voltage, 50/60Hz
b. Dimmable 0-10V analog 1% dimming control standard
a. “D010” designates this standard driver
c. Fixed lumen output
i. Lumens are selected when ordering the frame/collar
ii. 1000 lm and 1500 lm luminaires are IC and Non-IC
iii. 10 = 1000 lm (IC and Non-IC rated)
iv. 15 = 1500 lm (IC and Non-IC rated)
v. 20 = 2000 lm (Non-IC rated)
vi. 30 = 3000 lm (Non-IC rated)
vii. 40 = 4000 lm (Non-IC rated)
d. Example frame model number
i. HC4R15D010 =
i. 4-inch retrofit collar (frame) with 1500 lumen driver
HC4R Driver
4
14 © 2018 Eaton. All Rights Reserved..
14
Halo Commercial HCR4 – Feature Specs
4-inch LED Retrofit Downlights – LED Module
5. LED Module – HM4 ordered separately (same used on HC4 new construction)
a. Low or high lumen module
i. Selected per the lumen value of the frame/driver
ii. HM412 = Low lumen 1000-1500-2000 lm
iii. HM434 = High lumen 3000-4000 lm
b. Color Rendering Index
i. 8 = 80 CRI
ii. 9 = 90 CRI
c. Correlated Color Temperature
i. 27 = 2700K
ii. 30 = 3000K
iii. 35 = 3500K
iv. 40 = 4000K
d. Example LED model number
i. HM412835 =
i. 4-inch LED module for 1000, 1500, or 2000 lm frame, 80 CRI, 3500K
5
HM4 High
Lumen LED
Module
HM4 Low
Lumen LED
Module
15 © 2018 Eaton. All Rights Reserved..
15
Halo Commercial HCR4 – Feature Specs
4-inch LED Retrofit Downlights - Reflectors
7. Reflectors – 42R series
a. Self-flanged, downlight
b. Finishes
i. C = Specular Clear w/ polished flange
ii. H= Semi-Specular Haze - w/ polished flange
iii. W = Matte White – w/ white flange
iv. “WF” white flange option on Specular, Semi-Specular
c. Beam distribution
i. Medium
d. Non-conductive polymer reflector
i. May be used to meet codes and specifications for “dead front” trim
7
Beam Distribution*
4 Inch Medium
SC 1.0
Beam
Angle 55°
42RPSMDW
White Polymer
(Dead Front)
42RMDH
Semi-Specular
(Haze)
42RMDC
Specular Clear
42RMDW
White
*Nominal values
SC = Spacing Criteria
16 © 2018 Eaton. All Rights Reserved..
8. Emergency backup - factory installed
a. Use with standard “D010” 0-10V dimming driver
b. Remote emergency battery backup 7W or 14W, remote test switch
9. Connected lighting - factory installed
a. Use with standard “D010” 0-10V dimming driver
b. LumaWatt Pro: “LWPD1” controller, tile mount wireless sensor
c. WaveLinx: “SWPD1” relay w/ 0-10V dimming, tile mount wireless sensor
16
Halo Commercial HCR4 – Factory Installed Options
4-inch LED Retrofit Downlights - EM & Connected Lighting
9b
LumaWatt Pro
control & sensor WaveLinx relay &
sensor
9c 8
Remote Emergency
Battery Backup
17 © 2018 Eaton. All Rights Reserved..
17
Halo Commercial HC4
4-inch LED Retrofit Downlights – Dimensions
Reflector Max.
Height
Trim
Height
LED
Height
Medium 4.06” 2.57” 3.57”
LOW LUMEN
1000lm, 1500, 2000lm
18 © 2018 Eaton. All Rights Reserved..
18
Halo Commercial HC4
4-inch LED Retrofit Downlights – Dimensions
HIGH LUMEN
3000lm, 4000lm
Reflector Max.
Height
Trim
Height
LED
Height
Medium 6.36” 2.57” 3.57”
19 © 2018 Eaton. All Rights Reserved..
HOUSING HC4 15 D010 REM7 MODULE HM4 12 835
Housing Lumens Driver Options Module Lumens CRI / CCT
HC4 =
4” new
construction
and
remodeler
frame
HC4CP =
4” Chicago
Plenum new
construction
and
remodeler
frame
Fixed, Factory Set
10 = 1000 lumens
(nominal), use with
HM412 module
15 = 1500 lumens
(nominal), use with
HM412 module
20 = 2000 lumens
(nominal), use with
HM412 module
30 = 3000 lumens
(nominal), use with
HM434 module
40 = 4000 lumens
(nominal), use with
HM434 module
D010 = 120 -
277V 50/60Hz
0 – 10V 1% -
100%
dimming
REM7 = 7W Remote
Emergency battery w/
remote indicator & test
switch (D010 only)*
REM14 = 14W Remote
Emergency battery w/
remote indicator & test
switch (D010 only) *
IEM7 = 7W Integral
Emergency battery w/
integral indicator & test
switch (D010 only) *
IEM14 = 14W Integral
Emergency battery w/
integral indicator & test
switch (D010 only) *
HM4 = 4” LED
module. Use
with 41 & 42
series
reflectors
Compatible
with HC4 &
HC4R frames
12 = 1000, 1500,
2000 lumens
(nominal)
34 = 3000, 4000
lumens (nominal)
827 = 80CRI / 2700K
830 = 80CRI / 3000K
835 = 80CRI / 3500K
840 = 80CRI / 4000K
927 = 90CRI / 2700K
930 = 90CRI / 3000K
935 = 90CRI / 3500K
940 = 90CRI / 4000K
Footnote: *Not available
in Chicago
Plenum
LWTPD1 = Factory
installed LumaWatt
Pro tile mount sensor
kit (D010 only)*
SWPD1 = WaveLinx
tile mount sensor kit
(D010 only)*
ACCESSORIES
HB128APK = L channel hanger bar, 26”, ‘No-Fuss’, pair
(replacement)
RMB22 = 22” long wood joist mounting bars, pair
H347 = Step down transformer 347V input, 75VA max
H347200 = Step down transformer 347V input, 200VA max
PORLWTPD1 = LumaWatt Pro Sensor kit (D010 only)
TWSWPD1 = WaveLinx sensor kit (D010 only)
Halo Commercial HC4 4-Inch Downlight
Ordering with Standard 0-10V Dimming Driver
20 © 2018 Eaton. All Rights Reserved..
HOUSING HC4 15 DLV REMV7 MODULE HM4 12 835
Housing Lumens Driver* Options Module Lumens CRI / CCT
HC4 =
4” new
construction
and
remodeler
frame
Fixed, Factory Set
10 = 1000 lumens
(nominal), use with
HM412 module
15 = 1500 lumens
(nominal), use with
HM412 module
20 = 2000 lumens
(nominal), use with
HM412 module
30 = 3000 lumens
(nominal), use with
HM434 module
40 = 4000 lumens
(nominal), use with
HM434 module
DLV =
distributed low
voltage
dimming (1%-
100%) driver
For use with
Eaton’s DLVP
system
Refer to DLVP
low-voltage
power module
& DLVP
specifications
for details
REMV7 = 7W Remote
Emergency battery w/
remote indicator & test
switch (DLV only)*, **
REMV14 = 14W
Remote Emergency
battery w/ remote
indicator & test switch
(DLV only)*, **
IEMV7 = 7W Integral
Emergency battery w/
integral indicator & test
switch (DLV only) *, **
IEMV14 = 14W Integral
Emergency battery w/
integral indicator & test
switch (DLV only) *, **
HM4 = 4” LED
module. Use
with 41 & 42
series
reflectors
Compatible
with HC4 &
HC4R frames
12 = 1000, 1500,
2000 lumens
(nominal)
34 = 3000, 4000
lumens (nominal)
827 = 80CRI / 2700K
830 = 80CRI / 3000K
835 = 80CRI / 3500K
840 = 80CRI / 4000K
927 = 90CRI / 2700K
930 = 90CRI / 3000K
935 = 90CRI / 3500K
940 = 90CRI / 4000K
Footnote: *Not available
in Chicago
Plenum
**ULus Listed
U.S. only
ACCESSORIES
HB128APK = L channel hanger bar, 26”, ‘No-Fuss’, pair
(replacement)
RMB22 = 22” long wood joist mounting bars, pair
H347 = Step down transformer 347V input, 75VA max
H347200 = Step down transformer 347V input, 200VA max
Halo Commercial HC4 4-Inch Downlight
Ordering with Distributed Low Voltage Driver
21 © 2018 Eaton. All Rights Reserved..
REFLECTOR 41 MD C WF
Reflector Beam Distribution* Finish Flange Accessories
41 = 4” reflector,
use with HM4
LED modules
ND = narrow 45° beam, 0.76SC
MD = medium 55° beam, 1.00SC
WD = wide 65° beam, 1.20SC
RWW = wide beam with rotatable
linear spread lens wall wash
C = specular clear
H = semi-specular
haze
W= white
Blank = polished flange on C
& H
Blank = White flange on W
WF = white flange option
available with C &H
41RWWPK =
rotatable wall wash
insert for 4” reflector -
replacement part kit
41 = 4” baffle, use
with HM4 LED
modules
WD = wide 65° beam, 1.20SC
RWW = wide beam rotatable
linear spread lens wall wash
BB = black baffle
WB = white baffle
Blank = white flange on BB
and WB reflectors
41RWWPK =
rotatable wall wash
insert for 4” reflector -
replacement part kit
41 = 4” reflector,
Integral EM, use
with HM4 modules
ND = narrow 45° beam, 0.76SC
MD = medium 55° beam, 1.00SC
WD = wide 65° beam, 1.20SC
C = specular clear
H = semi-specular
haze
W= white
Blank = polished flange on C
& H
Blank = White flange on W
WF = white flange option
available with C &H
IEM = reflector
modified for integral
emergency
41 = 4” baffle,
Integral EM, use
with HM4 modules
WD = wide 65° beam, 1.20SC BB = black baffle
WB = white baffle
Blank = white flange on BB
and WB reflectors
IEM = reflector
modified for integral
emergency
41PS = 4” Non-
Conductive, use
with HM4 modules
MD = medium 55° beam, 1.00SC W= white
Blank = white flange on W
Halo Commercial HC4 4-Inch Downlight
Ordering - Reflectors
*Nominal values
22 © 2018 Eaton. All Rights Reserved..
HOUSING HC4R 15 D010 REM7 MODULE HM4 12 835
Housing Lumens Driver Options Module Lumens CRI / CCT
HC4R =
4” retrofit kit
for existing
open frame
housings
Fixed, Factory Set
10 = 1000 lumens
(nominal), use with
HM412 module
15 = 1500 lumens
(nominal), use with
HM412 module
20 = 2000 lumens
(nominal), use with
HM412 module
30 = 3000 lumens
(nominal), use with
HM434 module
40 = 4000 lumens
(nominal), use with
HM434 module
D010 = 120 -
277V 50/60Hz
0 – 10V 1% -
100%
dimming
REM7 = Remote
Emergency battery w/
remote indicator & test
switch (D010 only)
REM14 = Remote
Emergency battery w/
remote indicator & test
switch (D010 only)
HM4 = 4” LED
module. Use
with 41 & 42
series
reflectors
Compatible
with HC4 &
HC4R frames
12 = 1000, 1500,
2000 lumens
(nominal)
34 = 3000, 4000
lumens (nominal)
827 = 80CRI / 2700K
830 = 80CRI / 3000K
835 = 80CRI / 3500K
840 = 80CRI / 4000K
927 = 90CRI / 2700K
930 = 90CRI / 3000K
935 = 90CRI / 3500K
940 = 90CRI / 4000K
LWTPD1 = Factory
installed LumaWatt
Pro tile mount sensor
kit (D010 only)
SWPD1 = WaveLinx
tile mount sensor kit
(D010 only)
ACCESSORIES
HB128APK = L channel hanger bar, 26”, ‘No-Fuss’, pair
(replacement)
RMB22 = 22” long wood joist mounting bars, pair
H347 = Step down transformer 347V input, 75VA max
H347200 = Step down transformer 347V input, 200VA max
PORLWTPD1 = LumaWatt Pro Sensor kit (D010 only)
TWSWPD1 = WaveLinx sensor kit (D010 only)
Halo Commercial HC4R 4-Inch Retrofit
Ordering with Standard 0-10V Dimming Driver
23 © 2018 Eaton. All Rights Reserved..
REFLECTOR 42R MD C WF
Reflector Beam Distribution* Finish Flange Accessories
42R= 4” reflector
for use with HC4R
collar only,
compatible with
HM4 modules
MD = medium 50° beam, 1.00SC C = specular clear
H = semi-specular
haze
W= white
Blank = polished flange on C & H
Blank = White flange on W
WF = white flange option available
with C &H
42RPS = 4” Non-
conductive
reflector for use
with HC4R collar
only, compatible
with HM4 modules
MD = medium 50° beam, 1.00SC W= white
Blank = white flange on W
Halo Commercial HC4 4-Inch Retrofit
Ordering - Reflectors
*Nominal values
24 © 2018 Eaton. All Rights Reserved..
• UNV 120-277V, 0-10V analog dimming driver dims to 1%
• Factory installed emergency options:
• 7W or 14W battery backup
• Remote or integral test switch
Electrical
• Frame: “boat-shaped” allowing new construction or remodel
• Preinstalled “No Fuss” bars, captive and centered
• Bar brackets also accept EMT mounting
• Remodeler conversion: removable bar brackets allow frame to install from
below the ceiling
Frame
Mechanical
• CRI: 80CRI or 90CRI
• Color temperature options: 2700K, 3000K, 3500K, 4000K
• Lumen options:
• Low lumen range: 1000, 1500, or 2000 lm
• High lumen range: 3000 or 4000 lm
Color Lumens
• Factory installed connected lighting options:
• LumaWatt Pro wireless sensor - daylight, motion, heat, asset tracking
• WaveLynx wireless set-up and code compliance with daylight sensing
• DLVP - DC driver in Eaton distributed low voltage power system
Connected Lighting
Halo Commercial HC4 – Quick Specs
4-inch LED Downlights
25 © 2018 Eaton. All Rights Reserved..
• Precision formed spun aluminum reflectors
• Narrow 0.45° (0.76SC), Medium 55° (1.0SC), Wide 65° (1.2SC)
• Exclusive rotatable linear spread lens wall wash
• Non-Conductive “dead front” polymer reflector
Reflector
Mechanical
Optical
• Specular Clear, Semi-Specular Haze, White, White Baffle, Black
Baffle and Lensed wall wash
• Polished flange on specular, semi-specular
• White flange “WF” option on specular, semi-specular
• Optics optimize delivered lumens for lower power density W/Sq.Ft.
Reflector
Finishes
• Linear spread lens wall wash insert Accessory
• cULus damp & wet listed, and IP65
• Energy Star – certified light fixtures database
• Can be used for T24 Part 6 residential 1000lm & 1500lm, ICAT, 90CRI
• T24 Part 6 non-residential 2000lm, 3000lm, 4000lm, non-IC, 80 or 90 CRI
Listings
Halo Commercial HC4 – Quick Specs
4-inch LED Downlights
26 © 2018 Eaton. All Rights Reserved..
Commercialization –
• Sample case
• 4-Inch housing, module & trims
• Specification sheets - online
• Brochure – online & print
• IES files - online
• Dimming Guide – online
• Chromaticity Tech Note - online
• In stock with pricing in Flash
Halo Commercial HC4
Commercialization
27 © 2018 Eaton. All Rights Reserved..
Greengate Wallbox Dimmers & Sensors
• Eaton Lighting catalog numbers
• 0-10V dimmers
• Sensor technology options
• Passive Infrared
• Ultrasonic
• Dual Technology
• Daylighting (-R/MV/DMV models) limit
lighting when room is lit by sunlight
Halo Commercial HC4 – Wallbox Controls
4-inch LED Downlights
Dimmer / PIR Sensor
Occupancy or Vacancy
0-10V Dimmer
120/277V
Occupancy OSW-P-010-*
Vacancy VSW-P-010-*
Slide Dimmer
0-10V Dimmer
120/277V
WBSD-010SLD-*
Decorator Dimmer
0-10V Dimmer
120/277V
WBSD-010DEC-*
Occupancy PIR Sensor
120/277V
OSW-P-1001-MV-*
ONW-P-1001-MV-*
ONW-P-1001-DMV-*
Vacancy PIR Sensor
120/277V
VNW-P-1001-MV-*
VNW-P-1001-DMV-*
Occupancy PIR Sensor
120/277V
VNLW-P-1001-MV-N-* Occupancy Ultrasonic Sensor
120/277V
OSW-U-0721-MV-*
Occupancy & Vacancy
Dual Technology
120/277V
ONW-D-1001-MV-*
VNW-D-1001-MV-*
ONW-D-1001-DMV-*
VNW-D-1001-DMV-*
ONW-D-1001-DMV-N*
ONW-D-1001-MV-N-*
Color Kits
Lt. Almond, White, Ivory
Black, White, Gray
Brochure: Wallbox Controls Line Card
Resources>Library>Literature>Controls
28 © 2018 Eaton. All Rights Reserved..
Greengate Room Controller
• Three output relays
• Three 0-10 VDC dimming outputs
• Each 0-10V control supports up to 50 dimming drivers sourcing 2mA
• 120/277V, 20A input
• Control Devices
• Wallstations, occupancy/vacancy sensors, daylight sensors, receptacle controllers
• Connect via QuickConnect Class 2 cables to room controller
Halo Commercial HC4 – Room Controller
4-inch LED Downlights
Brochure: Greengate Room Controller System
Resources>Library>Literature>Controls
29 © 2018 Eaton. All Rights Reserved..
DLVP System • DLV factory installed driver option
• Low voltage power supply
• Order separately
• Powers the downlight low voltage driver
• 300W or 600W power supply units
• Note wattage max limit per run when laying out luminaires
• Plenum rated enclosure
• Addressable w/ accessory remotes
• Dimming 1% to 100%
• Plenum rated pre-terminated cables
• Order separately
• Supply power & communications
• Simplified installation and configuration
• Up to 40% lower labor install hours
• Up to 20% lower installed system cost
• Tile mount daylighting and occupancy sensors
Halo Commercial HC4 – DLVP Option
4-inch LED Downlights
Brochure: Distributed Low Voltage Power System
Resources>Library>Literature>Connected Systems
30 © 2018 Eaton. All Rights Reserved..
WaveLinx
• Tile mount daylight sensor and control unit
• Control unit includes 120-277VAC 3amp
relay pack with 0-10V dimming control
• Control relay pack mounts to fixture
junction box
• Automatic code commissioning meets or
exceeds code requirements
• Reduces commissioning time 40%
• Mobile app for building managers to easily
adjust settings
Factory Installed
SWPD1 = WaveLinx factory kit (ordered
with the housing frame)
Field Installed Accessory Kit
TMSWPD1 = WaveLinx field installed kit
(order separately)
Halo Commercial HC4 – WaveLinx
4-inch LED Downlights
Brochure: WaveLinx
Resources>Library>Literature>Connected Systems
31 © 2018 Eaton. All Rights Reserved..
LumaWatt Pro with Enlighted
• Tile mount sensor and control unit
• Monitor real time occupancy, light levels,
temperatures and energy usage
Factory Installed
LWTPD1 = LumaWatt factory kit (ordered
with the housing frame)
Field Installed Accessory Kit
PORLWTPD1 = LumaWatt field installed
kit (order separately)
Wireless
data
Halo Commercial HC4 – LumaWatt Pro
4-inch LED Downlights
Brochure: LumaWatt Pro
Resources>Library>Literature>Connected Systems
32 © 2018 Eaton. All Rights Reserved..