GUIDE ASSEMBLY - productload.johnsonfit.comproductload.johnsonfit.com/inc/.../assembly_guide/... · knuckle joint of the pedal arm assembly onto the right rotation axle. The pedal

ORANGE BAG

PINK BAG

GREEN BAG

M8 NutQuantity: 4

M5x12L BoltQuantity: 12


8x18x1T WasherQuantity: 4

M8X15L BoltQuantity: 6


25x34x2T Wavy WasherQuantity: 2

8x25x1.5T WasherQuantity: 2


BLUE BAG




Nylon Nut CoverQuantity: 2


SS41 Link Joint SleeveQuantity: 2




M4x12L ScrewQuantity: 2

Nylon Interval RingQuantity: 4

TOOLS & PARTS INCLUDED

Screwdriver

5mm L-Shaped Wrench

PARTS BOX13mm Wrench

Console Mast BootDual-Action Link Arm Covers

Dual-Action Axle CoversPedal Arm Joint CoversRight and Left Footplates

Rear StabilizersWater Bottle and Cage

Power Supply Color Coded Hardware Bags

Owners ManualAssembly GuideWarranty Card

13mm WrenchQuantity: 1

5mm T-Shaped Wrench

8x17x1T Arc WasherQuantity: 2

SW8 Lock WashersQuantity: 6



ASSEMBLY GUID

E

X1500ELLIPTICAL TRAINER

s t a r t s

v i s i o nw i t h a

i t a l l

ve

rs

at

il

es

mo

ot

ha

cc

es

si

bl

e

500 South CP Avenue • P.O. Box 280 • Lake Mills, WI 53551

toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373

www.visionfitness.com

©2008 Vision Fitness. All Rights Reserved. May be covered by one or more patents or patents pending: US 5540637, US 5573480, US 5813949, US 5813949, US 5924962, US 5938567, US 6135927, US 6149551, US 7316633, TW 364373, TW 371899, CN 99808486.7

9.08AG18.34PRD

REV8

ORANGE BAG

PINK BAG

GREEN BAG

M8 NutQuantity: 4




M8X15L BoltQuantity: 6



8x25x1.5T WasherQuantity: 2


BLUE BAG




Nylon Nut CoverQuantity: 2


SS41 Link Joint SleeveQuantity: 2




M4x12L ScrewQuantity: 2

Nylon Interval RingQuantity: 4

TOOLS & PARTS INCLUDED

Screwdriver

5mm L-Shaped Wrench

PARTS BOX13mm Wrench

Console Mast BootDual-Action Link Arm Covers

Dual-Action Axle CoversPedal Arm Joint CoversRight and Left Footplates

Rear StabilizersWater Bottle and Cage

Power Supply Color Coded Hardware Bags

Owners ManualAssembly GuideWarranty Card

13mm WrenchQuantity: 1

5mm T-Shaped Wrench

8x17x1T Arc WasherQuantity: 2

SW8 Lock WashersQuantity: 6



ASSEMBLYGUIDE

X1500ELLIPTICALTRAINER

starts

visionwith a

it all

ve

rs

at

il

es

mo

ot

ha

cc

es

si

bl

e

500 South CP Avenue • P.O. Box 280 • Lake Mills, WI 53551

toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373

www.visionfitness.com

©2008 Vision Fitness. All Rights Reserved. May be covered by one or more patents or patents pending: US 5540637, US 5573480, US 5813949, US 5813949, US 5924962, US 5938567, US 6135927, US 6149551, US 7316633, TW 364373, TW 371899, CN 99808486.7

9.08AG18.34PRD

REV8

To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order.Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enterhere:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and inyour own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble yourElliptical Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts andscrews are in place and partially threaded in before completely tightening any ONE bolt or screw.

A s s e m b l yG u i d e

X1500ELLIPTICAL TRAINER

4STEP

1STEP

2STEP

Stab i l i zerCover

1STEP ORANGE BAG

2STEP

• Slide a wavy washer (25x34x2T) onto the right rotation axle. Slide the knuckle joint of the pedal arm assemblyonto the right rotation axle. The pedalarm roller wheel should be placed intothe groove of the guide rail. Secure thepedal arm assembly to the rotation axlewith a washer (8x38x2T) and bolt(M8x20L). Tighten with the 5mm T-shaped wrench.

• Place the pedal arm cover over theknuckle joint. Secure in place with awasher (4x10x1T) and bolt (M4x12L).Tighten with the screwdriver.

• Repeat both steps on the left side.

BLUE BAG

3STEP

• Slide the boot onto the console mast.

• Unfold the wire harness located inthe frame bracket. Wrap the end ofthe wire tie, located at the bottom ofthe console mast, around the end ofthe wire harness. Pull the wire tie andwire harness up through the consolemast while simultaneously sliding themast over the frame bracket.

• Slide a lock washer (SW8)followed by a flat washer (8x18x1T)onto four of the bolts (M8x15L). Insertthese bolts through the side of the mastto secure the mast to the frame. Slidea lock washer (SW8) followed by aarc washer (8x17x1T) onto the tworemaining bolts (M8x15L). Insert thesebolts through the holes in front of themast. Tighten all bolts with the 5mm T-shaped wrench.

• Slide the boot down the console mastand set it in place over the side covers.

• Remove the four bolts from the backof the console. Connect the wireharness to the plug in the back of theconsole. Connect the heart rate wiresinto the heart rate plugs in the back ofthe console. Attach the console to theconsole mast with the four consolebolts and screwdriver.

• Attach the water bottle cage to theconsole mast with the two boltslocated on the mast.

PINK BAG

4STEP

• Slide the dual-action axle cover intoplace over the console mast axle.Slide a wavy washer (25x34x2T)onto the console mast axle. Slide theright dual-action arm onto the axle. Fixin place with a washer (8x38x2T)and nylon nut (M8). Cover with theincluded nylon nut cover.

• Insert the link joint sleeve (SS41)into the socket joint of the right linkarm. Position the socket joint of thelink arm into the bracket at the bottomof the dual-action arm. Position theNylon Interval Rings between thesocket joint and bracket on each side.Insert a bolt (M8x45L) through thebracket, interval rings and socket jointsleeve. Secure in place with a washer(8x25x1.5T) and nylon nut (M8).Tighten with the 5mm T-shapedwrench and 13mm wrench.

• Position the link arm covers over thesocket joint and secure the two piecestogether with a screw (M4x12L).Tighten with the screwdriver. Connectthe cover to each side of the link armwith a washer (5x10x1T) and bolt(M5x12L). Tighten with the screwdriver.

• Position the right footplate onto theright link arm. Secure in place withfour washers (6x14x1T) and four bolts(M5x12L). Tighten with the screwdriver.

• Repeat steps on the left side.

• Attach the hand grips onto the dual-action arms by turning grip in aclockwise direction. Make sure it is tight.

GREEN BAG

3STEP

Stab i l i zerShaft

Conso leMast

Conso le

Boot

L ink ArmCovers

Dua l -Act ionAxle Cover

Footp late

Dua l -Act ionArm

Hand Gr ips

• Slide the stabilizer shaft through theplastic sleeves in the rear support tube.NOTE: A tight fit between the shaftand sleeves is important to the stabilityof the unit. Because of this, it may behelpful to tap the shaft through with arubber mallet.

• Slide the stabilizer covers onto thestabilizer shaft and secure with(M8x20L) bolts and (8x16x1T) flatwashers. Tighten with the 5mm T-shaped wrench.

• Attach end caps to the end of theguide rails with (M8x15L) bolts. Tightenwith the 5mm T-shaped wrench.

End Cap

Peda l ArmCover

Peda l ArmAssembly

Knuck leJo int

Rotat ionAxle

Hand Gr ips

SIMPLEDELUXE

PREMIERCONSOLES

5STEP

• Refer to Product Selection andModel Configuration decal onconsole or follow these steps.

• Once the product is plugged in turnon the console

• Select product (Bike (BK) or Elliptical(EP)) using the resistance arrow keys.Press ENTER to select.

• Select model number (Bike (1500,2050, 2250, 3200) or Elliptical(1500, 6000, 6200)) using theRESISTANCE arrow keys. PressENTER to select. Console will reset tostart-up screen.

• The product selection and modelconfiguration is now complete.

CONSOLE

Documents

GUIDE ASSEMBLY - productload.johnsonfit.comproductload.johnsonfit.com/inc/.../assembly_guide/... · knuckle joint of the pedal arm assembly onto the right rotation axle. The pedal