1

High reliability and durability together with reduced maintenance requirement and wear partsCombined oil cooling and lubrication prevents corrosion and cavitationExcellent load takeover characteristics ensure prompt power supply

Low installation costs

Operating costsLong service intervals: 1000 hour oil change intervals and low fuel consumption bring savings in

Low noise emission, cost savings as no noise attenation measures are required

Technical description

Optimized cast iron cylinder block with optimum distribution of forcesPiston cooling for low piston temperature and reduced ring temperature Powerful but 18.1 litre naturally aspirated 6 cylinder compact EngineCrankshaft hardened bearing surfaces and fillets for moderate on main and big end bearingsKeystone top compression rings for long service life Replaceable valve guides and valve seatsThermostatically controlled system with gear driven circulation pump Lift eyeletsHigh inertia flywheel to SAE J620Flywheel for �flexible coupling and friction clutch Front engine mounting brackets

Benefits

GREEN POWER PERKINS DIESEL ENGINE

Type GP600P1500 RPM

The Engine with integrated water cooling

Engine: 2806A-E18TAG1A

••

••

••

••

•••

•••

••

•

•• Split element fuel filter

Mechanically governed cassette type fuel injection pump

Fuel System

Oil System

Spin-on full flow lub oil filterWet steel sump with filler and dipstick•

•

The engine and alternator are mounted together forming a rigid monoblock, the shoulders are connected by inflexible disc connection. The mono-block is mounted on a steel base frame through silent blocks. The base frame is including a fuel tank. Starting is electric and it contains a battery. The generator monitoring system consists of a control module.

Prime power is available for an unlimited number of annual hours in variable load application. A 10% overload capability is available for a period of 1 hour within a 12-hour period of operation.

The Genset 2806A-E18TAG1A Engine.

Oil pressure and coolant temperature switches

Glow plug cold start aid and heater/starter switch

12 volt starter motor and 12 volt 15 amp alternator with DC output

Control PanelManual or Automatic start control panel

12 volt Electronic shut Off Solenoid(ESOS) energised to run

2806A-E18TAG1AEngine type

Speed

Frequency

min | rpm-1 1500

Hz 50

Engine Power

Limited time running power (LTP)

Prime power (PRP) kVA KW

kVA KW

600

660

Fuel consumption

Rating Table :

PRP* kVA/KW :

|

|

480

528

|

|

LTP** kVA/KW : The standby power rating is applicable for supplying emergency power for the duration of a utilitypower interruption. No overload, utility parallel or negotiated outage operation capability is available at this rating.

Scope of supply :

2

••

••

201Standby power

75 % of Prime power

50 % of Prime power

g/KWh | l/hr

l/hr| KWh g/

l/hr| KWh g/

l/hr| KWh g/

134| | 123203

| 90199

| 61203

100 % of Prime power

KW

C

/min3m 110Exhaust gas flow

Exhaust gas Temperature 550o

Litres

Ah

568/761Max standby power at rated RPM

62Oil Tank capacity

1000Battery

Coolant capacity 61

KW

l

528

Numer of cylinder

Engine type 2806A-E18TAG1A

6

Bore x Stroke

DisplacementCompression ratio

mm 145 x 18318.1

14.5:1

Engine Power PRP 480

Engine Power LTP

Cooling Type water

Injection Type Indirect

Dry weight Kg 2050

Technical Data

Dimensions

Engine type Length HeightWidth

2806A-E18TAG1A 2545mm 18081536

3

Litres

KW/HP

Engine Illustration

4

1234567

Crankcase breatherSecondary fuel filtersPrimary fuel filterOil sampling valveOil filterFuel injection pumpOil gauge (dipstick)

Engine Description

2806A-E18TAG1A

5

Helsingborgsvägen Varalöv

262 96 Ängelholm

Tel: 0431 222 40Fax: 0431 222 70E mail: info@greenpower.seweb:www.greenpower.se

Greenpower AB

891011121314151617

Air intakeOil fillerFront lifting eyeAlternatorExhaust elbowExhaust manifoldTurbochargerFuel priming pumpStarting motorOil pan

Engine Description

2806A-E18TAG1A

Rear lifting eyeDrain plug (coolant)Drain plug (oil)

201918