Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061 phone: 847.478.2100 An ISO9001 Certified Company

1 | P a g e R 7 2 - 1 2 1 - S L S A S G - 0 0 5

How To Procedure

GOT Program Restore using GT Designer 3

Revision: A

Purpose: To restore all program files to the GOT

Required Tools:

PC with GT Designer 3 installed Generic USB Mini B cable

Consumable Parts:

None

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061 phone: 847.478.2100 An ISO9001 Certified Company

2 | P a g e R 7 2 - 1 2 1 - S L S A S G - 0 0 5

Task 1: Connect the USB MINI B cable between PCs USB port and GT1000 Front USB port. When cable is connected for the first time the USB Driver will automatically be installed.

.

Pull here to access the USB port

Pull here to access the USB port

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061 phone: 847.478.2100 An ISO9001 Certified Company

3 | P a g e R 7 2 - 1 2 1 - S L S A S G - 0 0 5

Task 2: Open the GT Designer3 back up saved Project File from hard drive location and double click on the [*.GTW] file.

Task 3: Select the communication method

Step1: Follow this step to set the communication Method to connect the personal computer to the GOT with a USB cable.

a) Select [Communication Configuration] from the Communication Menu.

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061 phone: 847.478.2100 An ISO9001 Certified Company

4 | P a g e R 7 2 - 1 2 1 - S L S A S G - 0 0 5

b) Select [USB]

c) Click on the [Test] Button

d) The following Window should appear. If it does not, disconnect the USB cable from PC and reconnnect to try again. Click on the [OK] button to close.

e) Click on the [OK] button to close Communication Configuration Window.

b

c e

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061 phone: 847.478.2100 An ISO9001 Certified Company

5 | P a g e R 7 2 - 1 2 1 - S L S A S G - 0 0 5

Task4: Write to GOT Step 1: From the [Communication] Menu, Select [Write to GOT]

Step 2: Click the [OK] Button, USB should be the Communication method selected.

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061 phone: 847.478.2100 An ISO9001 Certified Company

6 | P a g e R 7 2 - 1 2 1 - S L S A S G - 0 0 5

Step 3: Click the [GOT Write] button. All other items should be kept at Default as shown here except the

two items below.

1. If a Compact Flash Card is installed and the Project Files are too large to fit in the [C: Built-in Flash Memory], Select [A: Standard CF Card] in the Destination Drive Selection. Item a.

2. If this is a NEW GOT, the selection [Include required OS in the project data] must also

be selected. Item b.

a b

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061 phone: 847.478.2100 An ISO9001 Certified Company

7 | P a g e R 7 2 - 1 2 1 - S L S A S G - 0 0 5

Step 4: The following Window will appear.

Click the [YES] button to continue When Finished the following window will appear and the GOT Hardware will Reboot itself.

Click the [OK] button to continue

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061 phone: 847.478.2100 An ISO9001 Certified Company

8 | P a g e R 7 2 - 1 2 1 - S L S A S G - 0 0 5

The Communicate with GOT Window will now appear and show you the Write Data Size and the Write Drive Information.

Step 5: Click the [Close] button

Task5: Recycle the GOT Power

If the GOT prompts you to Cycle Power do so at this time. Otherwise the Restore procedure is

complete.