GmbH Certificate D PL - DAkkS · Annex to the Accreditation Certificate D ‐PL ... Testing concrete in structures ‐ Part 1: Cored specimens ‐ Taking, examining and testing in

This document is a translation. The definitive version is the original German annex to the accreditation certificate.

1/52

Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D‐PL‐11117‐01‐00 according to DIN EN ISO/IEC 17025:2005 Period of validity: 08.09.2015 until 10.04.2019 Date of issue: 08.09.2015

Holder of certificate:

TÜV Rheinland LGA Bautechnik GmbH Prüfstelle Baustoffe und Beton, Verkehrswegebau, Werkstoffe Tillystraße 2, 90431 Nürnberg Tests in the fields:

Testing of concrete and grout, cement, admixtures‐ and additives for concrete and grout, se‐lected aggregates for concrete and grout, floor screed, building bricks, aerated and lightweight concrete, concrete goods, artificial stone, drainage goods, insulating materials, ceilings, wooden building components, material and construction element testing ‐ Tests of mineral construction materials and natural stone ‐ Geotechnical ‐ ground and soil investiga‐tions, sampling and testing of soils, rock and aggregate samples ‐ Testing of bituminous mate‐rials, road marking materials, coatings as well as hot‐ and cold plastic masses ‐ non‐destructive testing of road surfaces and road areas ‐ mechanical structural test methods, tests of rein‐forcing steel, dynamic materials and components testing, testing of weld seams of metallic materials, metallographic and corrosion testing Test methods (investigation area I and special test methods of investigation area II) by third party testing authorities for the installation of mineral construction materials in landfill liner systems according to the Landfill Ordinance ‐ DepV and Federal Uniform Quality Standard BQS 9‐1 Testing of construction products and testing of fire resistance within the framework of EU Regulation No. 305/2011 laying down the harmonised conditions for the marketing of con‐struction products (Construction Products Regulation ‐ CPR) Abbreviations used: see last page

Annex to the Accreditation Certificate D‐PL‐11117‐01‐00

Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 2/52Date of issue: 08.09.2015

The testing laboratory is permitted, without being required to inform and obtain prior ap‐proval from DAkkS, to use standard testing methods listed here with different issue dates. This is valid for all areas of accreditation scope with the exception of section 4 (CPR). 1 Tests of concrete adhesives, concrete, grout, floor screed, building bricks and masonry,

admixtures and additives, mineral building products and natural stones 1.1 Binders and concrete DIN EN 196‐1 2005‐05

Methods of testing cement ‐ Part 1: Determination of strength ‐

DIN EN 196‐2 2013‐10

Method of testing cement ‐ Part 2: Chemical analysis of cement

DIN EN 196‐3 2009‐02

Methods of testing cement ‐ Part 3: Determination of setting times and soundness

DIN EN 196‐6 2010‐05

Methods of testing cement ‐ Part 6: Determination of fineness

DIN EN 196‐7 2008‐02

Methods of testing cement ‐ Part 7: Methods of taking and pre‐paring samples of cement

The above listed standards are to be used in connection with the follow‐ing guidance documents:

DIN EN 197‐1 2011‐11

Cement ‐ Part 1: Composition, specifications and conformity criteria for common cements

DIN EN 197‐2 2012‐01

Cement ‐ Part 2: Conformity evaluation

DIN EN 450‐1 2012‐10

Cement ‐ Part 1: Composition, specifications and conformity criteria for common cements

DIN EN 451‐2 1995‐01

Method of testing fly ash ‐ Part 2: Determination of fineness by wet sieving

DIN EN 1015‐3 2007‐05

Methods of test for mortar for masonry ‐ Part 3: Determination of consistence of fresh mortar (by flow table)



DIN EN 13454‐2 2007‐11

Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate ‐ Part 2: Test methods

in connection with:

DIN EN 13454‐1 2005‐1

Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate ‐ Part 1: Definitions and requirements

DIN EN 413‐2 2005‐08

Masonry cement ‐ Part 2: Test methods

DIN EN 520 2009‐12

Gypsum plasterboards ‐ Definitions, requirements and test methods

DIN 51043 1979‐08

Trass ‐ Requirements, Tests

DIN EN 480‐1 2011‐09

Admixtures for concrete, mortar and grout ‐ Test methods ‐ Part 1: Reference concrete and reference mortar for testing

DIN EN 480‐2 2006‐11

Admixtures for concrete, mortar and grout ‐ Test methods ‐ Part 2: Determination of setting time

DIN EN 480‐4 2006‐03

Admixtures for concrete, mortar and grout ‐ Test methods ‐ Part 4: Determination of bleeding of concrete

DIN EN 480‐11 2005‐12

Admixtures for concrete, mortar and grout ‐ Test methods ‐ Part 11: Determination of air void characteristics in hardened concrete

DIN EN 934‐6 2006‐03

Admixtures for concrete, mortar and grout ‐ Part 6: Sampling, conformity control and evaluation of conformity


DIN EN 12518 2008‐04

Chemicals used for treatment of water intended for human consumption ‐ High‐calcium lime

DIN EN 445 2008‐01

Grout for prestressing tendons ‐ Test methods



DIN EN 12350‐1 2009‐08

Testing fresh concrete ‐ Part 1: Sampling

DIN EN 12350‐2 2009‐08

Testing fresh concrete ‐ Part 2: Slump‐test

DIN EN 12350‐3 2009‐08

Testing fresh concrete ‐ Part 3: Vebe test

DIN EN 12350‐4 2009‐08

Testing fresh concrete ‐ Part 4: Degree of compactibility

DIN EN 12350‐5 2009‐08

Testing fresh concrete ‐ Part 5: Flow table test

DIN EN 12350‐6 2011‐03

Testing fresh concrete ‐ Part 6: Density

DIN EN 12350‐7 2009‐08

Testing fresh concrete ‐ Part 7: Air content ‐ Pressure methods

DIN EN 12350‐8 2010‐12

Testing fresh concrete ‐ Part 8: Self‐compacting concrete ‐ Slump‐flow test

DIN EN 12350‐11 2010‐12

Testing fresh concrete ‐ Part 11: Self‐compacting concrete ‐ Sieve segregation test

DIN EN 12350‐12 2010‐12

Testing fresh concrete ‐ Part 12: Self‐compacting concrete ‐ J‐ring test

DIN EN 12504‐1 2009‐07

Testing concrete in structures ‐ Part 1: Cored specimens ‐ Taking, examining and testing in compression

DIN EN 12504‐2 2012‐12

Testing concrete in structures ‐ Part 2: Non‐destructive testing ‐ Determination of rebound number

DIN 1048‐5 1991‐06

Testing concrete ‐ testing of hardened concrete (specimens pre‐pared in mould)

DIN EN 12390‐1 2012‐12

Testing hardened concrete ‐ Part 1: Shape, dimensions and other requirements for specimens and moulds



DIN EN 12390‐2 2009‐08 + Corrigenda 1 2012‐02

Testing hardened concrete ‐ Part 2: Making and curing specimens for strength tests


Testing hardened concrete ‐ Part 3: Compressive strength of test specimens (withdrawn standard)

DIN EN 12390‐5 2009‐07

Testing hardened concrete ‐ Part 5: Flexural strength of test specimens

DIN EN 12390‐6 2010‐09

Testing hardened concrete ‐ Part 6: Tensile splitting strength of test specimens

DIN EN 12390‐7 2009‐07

Testing hardened concrete ‐ Part 7: Density of hardened concrete

DIN EN 12390‐8 2009‐07

Testing hardened concrete ‐ Part 8: Depth of penetration of water under pressure

ZTV‐Ing, Teil 1 2012‐03

Additional terms of contract and guidelines for structural Engi‐neering ‐ general ‐ part 3 ‐ tests during construction ‐ part 3.3


ZTV‐Ing, Teil 3 2012‐03

Additional terms of contract and guidelines for structural Engineering ‐ solid structure ‐ part 4 ‐ protection and maintenance of concrete building parts ‐ annex B ‐ determination of concrete hu‐midity with the CM‐device

DAfStB RiLi Schutz und Instandsetzung von Betonbauteilen 2001‐10

DAfStB guideline for protection and maintenance of concrete building parts ‐ part 3: requirements for service companies and surveillance of execu‐tion

DAfStb RiLi Wasserge‐fährdende Stoffe 2011‐11

DAfStb ‐ guideline for concrete structural engineering using wa‐ter‐polluting substances ‐ annex A: test method (only test method A2)

DAfStb Heft 422 1991

Testing of concrete ‐ advice and hints as in addition to DIN 1048, only chapters 2.2, 2.5, 2.6 und 3.3



The above listed standards are to be used in connection with the follow‐ing guidance document:

DAStb‐Richtline 2010‐03

Steel fibre concrete

DIN 1048‐2 1991‐06

Testing concrete ‐ testing of hardened concrete (specimens taken in situ)

DIN 1048‐4 1991‐06

Test methods for concrete ‐ determination of the compressive strength in hardened concrete in structures and components ‐ application of reference lines and evaluation with special methods

DIN EN 13791 2008‐05

Assessment of in‐situ compressive strength in structures and precast concrete components

DIN EN 14488‐1 2005‐11

Testing sprayed concrete ‐ Part 1: Sampling fresh and hardened concrete

DIN EN 14488‐3 2006‐09

Testing sprayed concrete ‐ Part 3: Flexural strengths (first peak, ultimate and residual) of fibre reinforced beam specimens

DIN EN 14488‐4 2008‐08

Testing sprayed concrete ‐ Part 4: Bond strength of cores by di‐rect tension

DIN EN 14488‐6 2006‐09

Testing sprayed concrete ‐ Part 6: Thickness of concrete on a substrate

DIN EN 14488‐7 2006‐08

Testing sprayed concrete ‐ Part 7: Fibre content of fibre rein‐forced concrete

DIN EN 14845‐1 2007‐09

Test methods for fibres in concrete ‐ Part 1: Reference concretes

DIN EN 14845‐2 2006‐11

Test methods for fibres in concrete ‐ Part 2: Effect on concrete


DIN EN 14889‐1 2006‐11

Fibres for concrete ‐ Part 1: Steel fibres ‐ Defini‐tions, specifications and conformity

DIN EN 14889‐2 2006‐11

Fibres for concrete ‐ Part 2: Polymer fibres ‐ Definitions, specifications and conformity



DIN 1100 2004‐05

Hard aggregates for cement‐bound floor screeds ‐ Requirements and test methods

Other applicable documents:

ONR 23303 2010‐03

Test methods for concrete ‐ National application of testing standards for concrete and its source materials

ÖNORM B 4706 2008‐12

Repair, reconstruction and strengthening of concrete structures

1.2 Grout DIN 272 1986‐02

Testing of magnesium oxychloride screeds

DIN EN 1308 2007‐11

Adhesives for tiles ‐ Determination of slip

The above listed standards are to be used in connection with the following guidance document:

DIN EN 1323 2007‐11

Adhesives for tiles ‐ Concrete slabs for tests

DIN EN 1324 2007‐11

Adhesives for tiles ‐ Determination of shear adhesion strength of dispersion adhesives

DIN EN 1346 2007‐11

Adhesives for tiles ‐ Determination of open time

DIN EN 1347 2007‐10

Adhesives for tiles ‐ Determination of wetting capability

DIN EN 1348 2007‐11

Adhesives for tiles ‐ Determination of tensile adhesion strength for cementitious adhesives

DIN EN 1015‐1 2007‐05

Methods of test for mortar for masonry ‐ Part 1: Determination of particle size distribution (by sieve analysis)

DIN EN 1015‐2 2007‐05

Methods of test for mortar for masonry ‐ Part 2: Bulk sampling of mortars and preparation of test mortars



DIN EN 1015‐3 2007‐05

Methods of test for mortar for masonry ‐ Part 3: Determination of consistence of fresh mortar (by flow table)

DIN EN 1015‐4 1998‐12

Methods of test for mortar for masonry ‐ Part 4: Determination of consistence of fresh mortar (by plunger penetration)

DIN EN 1015‐6 2007‐05

Methods of test for mortar for masonry ‐ Part 6: Determination of bulk density of fresh mortar

DIN EN 1015‐7 1998‐12

Methods of test for mortar for masonry ‐ Part 7: Determination of air content of fresh mortar

DIN EN 1015‐9 2007‐05

Methods of test for mortar for masonry ‐ Part 9: Determination of workable life and correction time of fresh mortar

DIN EN 1015‐10 2007‐05

Methods of test for mortar for masonry ‐ Part 10: Determination of dry bulk density of hardened mortar

DIN EN 1015‐11 2007‐05

Methods of test for mortar for masonry ‐ part 11: determination of flexural and compressive strength of hardened mortar

DIN EN 1015‐12 2000‐06

Methods of test for mortar for masonry ‐ Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates

DIN EN 1015‐18 2003‐03

Methods of test for mortar for masonry ‐ Part 18: Determination of water absorption coefficient due to capillary action of hardened mortar

DIN EN 1015‐19 2005‐01

Methods of test for mortar for masonry ‐ Part 19: Determination of water vapour permeability of hardened rendering and plastering mortars

DIN EN 12002 2009‐01

Adhesives for tiles ‐ Determination of transverse deformation for cementitious adhesives and grouts

DIN EN 12003 2009‐01

Adhesive for tiles ‐ Determination of shear adhesion strength of reaction resin adhesives

The above listed standards are to be used in connection with the following guidance documents:

DIN EN 12004 2012‐09

Adhesives for tiles ‐ Requirements, evaluation of conformity, classification and designation



DIN EN 12004 2014‐02

Adhesives for tiles ‐ Requirements, evaluation of conformity, classification and designation

DIN 18555‐1 1982‐09

Testing of mortars containing mineral binders ‐ general, sampling, test mortar (withdrawn standard)

DIN 18555‐2 1982‐09

Testing of mortars containing mineral binders ‐ freshly mixed mor‐tars containing aggregates of dense structure (heavy aggregates) ‐ determination of consistence, bulk density and air content (withdrawn standard)

DIN 18555‐3 1982‐09

Testing of mortars containing mineral binders ‐ hardened mortars ‐ determination of flexural strength, compressive strength and bulk density

DIN 18555‐4 1986‐03

Testing of mortars containing mineral binders ‐ hardened mortars ‐ determination of linear and transverse strain and of deformation characteristics of masonry mortars by the static pressure test

DIN 18555‐5 1986‐03

Testing of mortars containing mineral binders ‐ hardened mortars ‐ determination of bond shear strength of masonry mortars (withdrawn standard)

DIN 18555‐6 1987‐11

Testing of mortars containing mineral binders ‐ determination of bond strength of hardened mortar

DIN 18555‐7 1987‐11

Testing of mortars containing mineral binders ‐ determination of water retentivity of freshly mixed mortar by the filter plate method

DIN 18555‐8 1987‐11

Testing of mortars containing mineral binders ‐ freshly mixed mor‐tar ‐ determination of workability time and correction time of thin‐bed mortar for use with masonry (withdrawn standard)

DIN 18555‐9 1999‐09

Testing of mortars containing mineral binders ‐ Part 9: Hardened mortars ‐ determination of the mortar compressive strength in the bed joint

DIN 18556 1985‐01

Testing of coating material for synthetic resin plasters and of syn‐thetic resin plasters (withdrawn standard)



1.3 Screeds DIN EN 13892‐1 2003‐02

Methods of test for screed materials ‐ Part 1: Sampling, making and curing specimens for test

DIN EN 13892‐2 2003‐02

Methods of test for screed materials ‐ Part 2: Determination of flexural and compressive strength

DIN EN 13892‐3 2004‐07

Methods of test for screed materials ‐ Part 3: Determination of wear resistance‐Böhme

DIN EN 13892‐8 2003‐02

Methods of test for screed materials ‐ Part 8: Determination of bond strength


DIN EN 13813 2003‐01

Screed material and floor screeds ‐ Screed mate‐rials ‐ Properties and requirements

DIN 18560‐1 2009‐09

Floor screeds in building construction ‐ Part 1: General requirements, testing and construction

DIN 18560‐2 2009‐09

Floor screeds in building construction ‐ Part 2: Floor screeds and heating floor screeds on insula‐tion layers

DIN 18560‐3 2006‐03

Floor screeds in building construction ‐ Part 3: Base‐bonded floor screeds

DIN 18560‐4 2012‐06

Floor screeds ‐ Part 4: Screeds laid on separated layer

DIN 18560‐7 2004‐04

Floor screeds ‐ Part 7: Heavy‐duty screeds (industrial screeds)

1.4 Building bricks and masonry DIN EN 846‐2 2000‐08

Methods of tests for ancillary components for masonry ‐ Part 2: Determination of bond strength of prefabricated bed joint rein‐forcement in mortar joints

DIN EN 846‐3 2000‐08

Methods of tests for ancillary components for masonry ‐ Part 3: Determination of shear load capacity of welds in prefabricated bed joint reinforcement



DIN EN 846‐4 2005‐01

Methods of test for ancillary components for masonry ‐ Part 4: Determination of load capacity and load‐deflection characteris‐tics of straps

DIN EN 846‐5 2012‐11

Methods of test for ancillary components for masonry ‐ Part 5: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (couplet test)

DIN EN 846‐6 2012‐11

Methods of test for ancillary components for masonry ‐ Part 6: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (single end test)

DIN EN 846‐7 2012‐11

Methods of test for ancillary components for masonry ‐ Part 7: Determination of shear load capacity and load displacement characteristics of shear ties and slip ties (couplet test for mortar joint connections)

DIN EN 846‐8 2006‐10

Methods of tests for ancillary components for masonry ‐ Part 8: Determination of load capacity and load‐deflection characteris‐tics of joist hangers

DIN EN 846‐9 2000‐08

Methods of tests for ancillary components for masonry ‐ Part 9: Determination of flexural resistance and shear resistance of lin‐tels

DIN EN 846‐10 2000‐08

Methods of test for ancillary components for masonry ‐ Part 10: Determination of load capacity and load deflection characteristics of brackets

DIN EN 846‐11 2000‐08

Methods of test for ancillary components for masonry ‐ Part 11: Determination of dimensions and bow of lintels

DIN EN 846‐13 2001‐12

Methods of test for ancillary components for masonry ‐ Part 13: Determination of resistance to impact, abrasion and corrosion of organic coatings

DIN EN 772‐1 2011‐07

Methods of test for masonry units ‐ Part 1: Determination of compressive strength

DIN EN 772‐6 2002‐02

Methods of test for masonry units ‐ Part 6: Determination of bending tensile strength of aggregate concrete masonry units

DIN EN 772‐14 2002‐02

Methods of test for masonry units ‐ Part 14: Determination of moisture movement of aggregate concrete and manufactured stone masonry units



DIN EN 772‐15 2000‐09

Methods of test for masonry units ‐ Part 15: Determination of water vapour permeability of autoclaved aerated concrete ma‐sonry units


DIN EN 845‐1 2013‐10

Specification for ancillary components for ma‐sonry ‐ Part 1: Wall ties, tension straps, hangers and brackets

DIN EN 845‐2 2013‐08

Specification for ancillary components for ma‐sonry ‐ Part 2: Lintels

DIN EN 845‐3 2013‐08

Specification for ancillary components for masonry ‐ Part 3: Bed joint reinforcement of steel meshwork

DIN V 18151‐100 2005‐10

Lightweight concrete hollow blocks ‐ Part 100: Hollow blocks with specific properties

DIN V 18152‐100 2005‐10

Lightweight concrete solid bricks and blocks ‐ Part 100: Solid bricks and blocks with specific properties

DIN V 18153‐100 2005‐10

Concrete masonry units (Normal‐weight concrete) ‐ Part 100: Masonry units with specific properties

DIN 105‐100 2012‐01

Clay masonry units ‐ Part 100: Clay masonry units with specific properties

1.5 Aerated and lightweight concrete DIN EN 678 1994‐02

Determination of the dry density of autoclaved aerated concrete

DIN EN 679 2005‐09

Determination of the compressive strength of autoclaved aerated concrete

DIN EN 680 2006‐03

Determination of the drying shrinkage of autoclaved aerated concrete

DIN EN 990 2003‐01

Test methods for verification of corrosion protection of reinforcement in autoclaved aerated concrete and lightweight aggregate concrete with open structure



DIN EN 991 1995‐09

Determination of the dimensions of prefabricated reinforced components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure

DIN EN 992 1995‐09

Determination of the dry density of lightweight aggregate con‐crete with open structure

DIN EN 1351 1997‐02

Determination of flexural strength of autoclaved aerated con‐crete

DIN EN 1352 1997‐02

Determination of static modulus of elasticity under compression of autoclaved aerated concrete or lightweight aggregate concrete with open structure

DIN EN 1353 1997‐02

Determination of moisture content of autoclaved aerated concrete

DIN EN 1354 2005‐09

Determination of compressive strength of lightweight aggregate concrete with open structure


DIN V 4165‐100 2005‐10

Autoclaved aerated concrete masonry units ‐ Part 100: High precision units and elements with specific properties

DIN 4166 1997‐10

Autoclaved aerated concrete slabs and panels

1.6 physical performance of construction products DIN EN ISO 12571 2013‐12

Hygrothermal performance of building materials and products ‐ Determination of hygroscopic sorption properties

DIN EN ISO 12572 2001‐09

Hygrothermal performance of building materials and products ‐ Determination of water vapour transmission properties

DIN EN 12667 2001‐05

Thermal performance of building materials and products ‐ Determination of thermal resistance by means of guarded hot plate and heat flow meter methods ‐ Products of high and medium thermal resistance



1.7 Roof panels, insulating materials, wooden structures, planked ceiling and suspended ceilings

DIN EN 492 2012‐12

Fibre‐cement slates and fittings ‐ Product specification and test methods, except 7.3.3, 7.4.2 und 7.5

DIN EN 494 2013‐01

Fibre‐cement profiled sheets and fittings ‐ Product specification and test methods, only 7.3.1 and 7.3.2

DIN EN 822 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of length and width

DIN EN 823 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of thickness

DIN EN 824 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of squareness

DIN EN 825 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of flatness

DIN EN 826 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of compression behaviour (here: without determination of 10%‐compression)

DIN EN 1602 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of the apparent density

DIN EN 1607 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of tensile strength perpendicular to faces

DIN EN 1608 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of tensile strength parallel to faces

DIN EN 1609 2013‐05

Thermal insulating products for building applications ‐ Determina‐tion of short term water absorption by partial immersion

DIN EN 12086 2013‐06

Thermal insulating products for building applications ‐ Determina‐tion of water vapour transmission properties

DIN EN 12087 2013‐06

Thermal insulating products for building applications ‐ Determina‐tion of water vapour transmission properties



DIN EN 12089 2013‐06

Thermal insulating products for building applications ‐ Determina‐tion of bending behaviour

DIN 4158 1978‐05

Filler concrete joists for reinforced and prestressed concrete floors

DIN 1052‐10 2012‐05

Design of timber structures ‐ Part 10: Additional provisions

DIN EN 1382 2000‐03

Timber structures ‐ Test methods ‐ Withdrawel capacity of timber fasteners

DIN EN 1383 2000‐03

Timber structures ‐ Test methods ‐ Pull through resistance of timber fasteners

DIN EN 14592 2012‐07

Timber structures ‐ Dowel‐type fasteners ‐ Requirements

DIN EN 14195 2011‐11

Metal framing components for gypsum board systems ‐ Defini‐tions, requirements and test methods

DIN EN 14316‐1 2004‐11

Thermal insulation products for buildings ‐ In‐situ thermal insula‐tion formed from expanded perlite (EP) products ‐ Part 1: Specifi‐cation for bonded and loose‐fill products before installation

DIN 18168‐2 2008‐05

Ceiling linings and suspended ceilings with gypsum plasterboards ‐ Part 2: Verification of the load‐carrying capacity of metal sub‐constructions and metal suspending rods

in connection with :

DIN 18168‐1 2007‐04

Ceiling linings and suspended ceilings with gypsum plasterboards ‐ Part 1: Requirements for construc‐tion

DIN EN 13964 2014‐08

Suspended ceilings ‐ Requirements and test methods

ETAG 003 1999

Guideline for european technical approval of internal partition kits for use as non‐loadbearing walls



1.8 Cast stones

DIN V 18500 2006‐12

Cast stones ‐ Terminology, requirements, testing, inspection


DIN 483 2005‐10

Concrete kerb units ‐ Shapes, dimensions, marking

DIN EN 1338 2003‐08 + Corrigenda 1 2006‐11

Concrete paving blocks ‐ Requirements and test methods, not annex G

E DIN EN 1338 2010‐08

Concrete paving blocks ‐ Requirements and test methods, not annex G

Bundesverband Deutsche Beton‐ und Fertigteil‐industrie e.V., Bonn 1996‐04

Guideline, production and quality assurance of permeable con‐crete paving blocks made of open matrix concrete


Concrete paving flags ‐ Requirements and test methods, not annex G

E DIN EN 1339 2010‐08

Concrete paving flags ‐ Requirements and test methods, not annex G


Concrete kerb units ‐ Requirements and test methods, not annex G

E DIN EN 1340 2010‐08

Concrete kerb units ‐ Requirements and test methods, not annex G

DIN EN 13748‐1 2005‐08

Terrazzo tiles ‐ Part 1: Terrazzo tiles for internal use, not section 5.6.1

DIN EN 13748‐2 2005‐03

Terrazzo tiles ‐ Part 2: Terrazzo tiles for external use, not section 5.6.1



The above listed standards are to be used in connection with the follow‐ing guidance document:

BGB‐RINGB 2006‐11

Non standardized concrete products ‐ Require‐ments and test methods

DIN 19555 2003‐04

Step irons for single‐line installation ‐ Step irons for setting in concrete

DIN 19555 Corrigenda 1 2006‐04

Step irons for single‐line installation ‐ Step irons for setting in concrete

DIN EN 13101 2003‐04

Steps for underground man entry chambers ‐ Requirements, marking, testing and evaluation of conformity

DIN EN 1433 2005‐09

Drainage channels for vehicular and pedestrian areas ‐ Classifica‐tion, design and testing requirements, marking and evaluation of conformity

DIN EN 124 1994‐08

Gully tops and manhole tops for vehicular and pedestrian areas ‐ design requirements, testing, marking, quality control

1.9 Mineral construction materials DIN EN 932‐1 1996‐11

Test for general properties of aggregates ‐ Part 1: Methods for sampling


ZTV wwG‐StB By 05 Az: IID9‐43437‐002/92 2005‐21‐12

Additional technical Conditions for contract and delivery for required water management relevant quality parameter for the use of recycled‐ road construction products in Bavaria, only section 6.1

DIN EN 932‐2 1999‐03

Test for general properties of aggregates ‐ Part 2: Methods for reducing laboratory samples

DIN EN 932‐3 2003‐12

Tests for general properties of aggregates ‐ Part 3: Procedure and terminology for simplified petrographic description



The above listed standards are to be used in connection with the following guidance document:

DIN EN 932‐5 2012‐05

Tests for general properties of aggregates ‐ Part 5: Common equipment and calibration

DIN EN 933‐1 2012‐03

Tests for geometrical properties of aggregates ‐ Part 1: Determina‐tion of particle size distribution ‐ Sieving method

ÖNORM EN 933‐1 2012‐03

Tests for geometrical properties of aggregates ‐ Part 1: Determina‐tion of particle size distribution ‐ Sieving method

ÖNORM EN 13286‐41 2003‐06

Unbound and hydraulically bound mixtures ‐ Part 41: Test method for the determination of the compressive strength of hydraulically bound mixtures

ÖNORM EN 13286‐42 2003‐06

Unbound and hydraulically bound mixtures ‐ Part 42: Test method for the determination of the indirect tensile strength of hydraulically bound mixtures

DIN EN 933‐3 2012‐04

Tests for geometrical properties of aggregates ‐ Part 3: Determina‐tion of particle shape ‐ Flakiness index

DIN EN 933‐4 2015‐01

Tests for geometrical properties of aggregates ‐ Part 4: Determina‐tion of particle shape ‐ Shape index

DIN EN 933‐5 2005‐02

Tests for geometrical properties of aggregates ‐ Part 5: Determina‐tion of percentage of crushed and broken surfaces in coarse aggregate particles

DIN EN 933‐6 2014‐07

Tests for geometrical properties of aggregates ‐ Part 6: Assessment of surface characteristics ‐ Flow coefficient of aggregates

DIN EN 933‐7 1998‐05

Tests for geometrical properties of aggregates ‐ Part 7: Determina‐tion of shell content ‐ percentage of shells in coarse aggregates



DIN EN 933‐8 2012‐04

Tests for geometrical properties of aggregates ‐ Part 8: Assessment of fines ‐ Sand equivalent test

DIN EN 933‐9 2013‐07

Tests for geometrical properties of aggregates ‐ Part 9: Assessment of fines ‐ Methylene blue test

DIN EN 933‐10 2009‐10

Tests for geometrical properties of aggregates ‐ Part 10: Assessment of fines ‐ Grading of filler aggregates (air jet sieving)

DIN EN 933‐11 2011‐05

Tests for geometrical properties of aggregates ‐ Part 11: Classifica‐tion test for the constituents of coarse recycled aggregate

DIN 52106 2013‐12

Testing of aggregates ‐ Test methods for the assessment of the weathering resistance

DIN EN 1097‐1 2011‐04

Tests for mechanical and physical properties of aggregates ‐ Part 1: Determination of the resistance to wear (micro‐Deval)

DIN EN 1097‐2 2010‐07

Tests for mechanical and physical properties of aggregates ‐ Part 2: Methods for the determination of resistance to fragmentation

DIN EN 1097‐3 1998‐06

Tests for mechanical and physical properties of aggregates ‐ Part 3: Determination of loose bulk density and voids

DIN EN 1097‐4 2008‐06

Tests for mechanical and physical properties of aggregates ‐ Part 4: Determination of the voids of dry compacted filler


Tests for mechanical and physical properties of aggregates ‐ Part 7: Determination of the particle density of filler ‐ Pyknometer method

DIN EN 1097‐8 2009‐10

Tests for mechanical and physical properties of aggregates ‐ Part 8: Determination of the polished stone value



DIN EN 1367‐2 2010‐02

Tests for thermal and weathering properties of aggregates ‐ Part 1: Determination of resistance to freezing and thawing


Tests for thermal and weathering properties of aggregates ‐ Part 3: Boiling test for "Sonnenbrand basalt”

DIN EN 1367‐5 2011‐04

Tests for thermal and weathering properties of aggregates ‐ Part 5: Determination of resistance to thermal shock

DIN EN 1367‐6 2008‐12

Tests for thermal and weathering properties of aggregates ‐ Part 6: Determination of resistance to freezing and thawing in the pres‐ence of salt (NaCl)


Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applica‐tions, not annex B

E DIN EN 13055‐1 2012‐05

Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applica‐tions, not annex B

DIN EN 13055‐2 2004‐09

Lightweight aggregates ‐ Part 2: Lightweight aggregates for bitumi‐nous mixtures and surface treatments and for unbound and bound applications

DIN 52115‐2 2014‐02

Test methods for aggregates ‐ Part 2: Impact test on crushed and broken aggregates larger than 32 mm

DIN EN 1744‐1 2013‐03

Tests for chemical properties of aggregates ‐ Part 1: Chemical analysis, only chapter. 14.2 und 15.1

DIN EN 13286‐2 2013‐02

Unbound and hydraulically bound mixtures ‐ Part 2: Test methods for laboratory reference density and water content ‐ Proctor com‐paction

DIN EN 13383‐2 2013‐08

Armourstone ‐ Part 1: Specification

DIN EN 13450 2013‐07

Aggregates for railway ballast, only annexes A, C and D



DIN EN 13179‐1 2013‐09

Tests for filler aggregate used in bituminous mixtures ‐ Part 1: Delta ring and ball test

TP Beton StB 10 ‐ Teil 3.1 2010

TP concrete‐StB 10 ‐ Technical test specifications for load bearing strata with hydraulic Binders and concrete road surfaces, part 3.1

TP Gestein‐StB Teil 3.1.4 2008

TP aggregates ‐StB: Technische test specification for aggregates for road construction ‐ material labelling of household waste incinera‐tor ash (municipal incinerator bottom ash aggregates)


Material labelling of recycled construction materials


Determination of grain size distribution of fine grain sizes (air jet sieving)


Determination of grain size distribution of Filler (air jet sieving)


Estimation of ratio rounded to fragmented parts in fine grain sizes using a Binocular

TP Gestein‐StB Teil 5.3.1.2 2008

Impact test on particle size distributions > 32 mm


Los Angeles‐test method on particle size distributions > 32 mm


Determination of polished stone value (PSVfGK)

TP Gestein‐StB Teil 5.6 2008

Determination of hardness ‐ Dynamic CBR‐test




Resistance of mineral grain size composition against freeze thaw cycles


Resistance of fine aggregates against frost and thaw changes


Resistance of coarse aggregates against heat exposure


Resistance of fine aggregates against heat exposure


Water sensitivity of fine aggregates ‐ shaking and abrasive method

DIN EN 12697‐11 2012‐07

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 11: Determination of the affinity between aggregate and bitumen

TP Asphalt‐StB Teil 11 2012

Technical test directives for Asphalt ‐ Part 11: adhesion between‐stone and Bitumen

1.10 Natural stone and brick DIN EN 1936 2007‐02

Natural stone test method ‐ Determination of real density and apparent density, and of total and open porosity

DIN EN 13755 2008‐08

Natural stone test methods ‐ Determination of water absorption at atmospheric pressure

DIN 52008 2006‐03

Natural stone test methods ‐ Assessment of the weathering resistance, only annexes C and D

DIN EN 1926 2007‐03

Natural stone test methods ‐ Determination of uniaxial compressive strength

DIN EN 12372 2007‐02

Natural stone test methods ‐ Determination of flexural strength under concentrated load



DIN EN 13161 2008‐08

Natural stone test methods ‐ Determination of flexural strength under constant moment

DIN EN 13364 2002‐03

Natural stone test methods ‐ Determination of the breaking load at dowel hole

DIN EN 14157 2005‐01

Natural stone test methods ‐ Determination of the abrasion resistance

DIN 51097 1992‐11

Testing of floor coverings ‐ determination of the anti‐slip proper‐ties ‐ wet‐loaded barefoot areas ‐ walking method ‐ ramp test

DIN 51130 2014‐02

Testing of floor coverings ‐ Determination of the anti‐slip property ‐ Workrooms and fields of activities with slip danger ‐ Walking method ‐ Ramp test

DIN EN 538 1994‐11

Clay roofing tiles for discontinuous laying ‐ Flexural strength test

DIN EN 539‐1 2005‐12

Clay roofing tiles for discontinuous laying ‐ Determination of physical characteristics ‐ Part 1: Impermeability test

DIN EN 539‐2 2013‐08

Clay roofing tiles for discontinuous laying ‐ Determination of physical characteristics ‐ Part 2: Test for frost resistance

DIN EN 1024 2012‐06

Clay roofing tiles for discontinuous laying ‐ Determination of geometric characteristics



2 Geotechnical site investigation, sampling and testing of soil, rocks and aggregate samples

2.1 Sampling DIN EN ISO 14688‐1 2013‐12

Geotechnical investigation and testing ‐ Identification and classification of soil ‐ Part 1: Identification and description

DIN EN ISO 14688‐2 2013‐12

Geotechnical investigation and testing ‐ Identification and classification of soil ‐ Part 2: Principles for a classification

DIN EN ISO 14689‐1 2011‐06

Geotechnical investigation and testing ‐ Identification and classification of rock ‐ Part 1: Identification and description

DIN EN ISO 22475‐1 2007‐01

Geotechnical investigation and testing ‐ Sampling methods and groundwater measurements ‐ Part 1: Technical principles for execution

DIN 4023 2011‐01

Geotechnical investigation and testing ‐ Graphical presentation of logs of boreholes, trial pits, shafts and adits

DIN 19672, Blatt 1 1968‐04

Apparatus for drawing soil samples in agricultural engineering ‐ apparatus for soil sampling in undisturbed situation

DIN 52101 2013‐10

Aggregates test methods ‐ Sampling

2.2 soil and ground physical investigation DIN EN ISO 22476‐2 2012‐03

Geotechnical investigation and testing ‐ Field testing ‐ Part 2: Dynamic probing

FGSV‐Nr. 591/B 15.1 2012

TP BF‐StB ‐ Technical test guidelines for soil and rock in road construction ‐ part B 15.1 – Light dynamic probing DPL‐5 und middle heavy dynamic probing DPM‐10

DIN 4094‐4 2002‐01

Construction site – tests in situ ‐ Part 4: vane shear test



TP BF‐StB Teil B 8.3 2003

Dynamic plate load test using a Drop‐Weight Tester

DIN 18035‐4 2012‐01

Sports grounds ‐ Part 4: Sports turf areas

DIN 18124 2011‐04

Soil, investigation and testing ‐ Determination of density of solid particles ‐ Capillary pycnometer, wide mouth pycnometer, gas pycnometer

DIN 18126 1996‐11

Soil, investigation and testing ‐ Determination of density of non‐cohesive soils for maximum and minimum compactness

DIN 18130‐2 2011‐07

Soil, investigation and testing ‐ Determination of the coefficient of water permeability ‐ Part 2: Field tests

DIN 18137‐1 2010‐07

Soil, investigation and testing ‐ Determination of shear strenght ‐ Part 1: Concepts and general testing conditions

DGGT‐Empfehlung Nr. 1 2004

Uniaxiale load tests on rock samples


Triaxiale load tests on rock samples


Point load tests on rock samples


Indirect tensile test on rock samples ‐ tension fatigue test


Swelling pressure test on rock samples


Multistep technic for triaxial load tests and direct tensile tests


Uni‐ and triaxial creep tests on rock samples



QMA 4.3‐05.5‐303 2013‐10

Swelling pressure tests


DGGT‐Empfehlung Nr. 111986

Swelling pressure test on rock samples

DIN EN 932‐3 2003‐12

Tests for general properties of aggregates ‐ Part 3: Procedure and terminology for simplified petrographic description

2.3 Test methods (investigation area I) by third party testing authorities for the installa‐tion of mineral construction materials in landfill liner systems according to the Land‐fill Ordinance ‐ DepV and Federal Uniform Quality Standard BQS 9‐1

DIN 18121‐1 1998‐04

Soil, investigation and testing ‐ Water content ‐ Part 1: Determina‐tion by drying in oven

DIN 18121‐2 2012‐02

Soil, investigation and testing ‐ Water content ‐ Part 2: Determina‐tion by rapid methods

DIN 18122‐1 1997‐07

Soil, investigation and testing ‐ Consistency limits ‐ Part 1: Deter‐mination of liquid limit and plastic limit

DIN 18123 2011‐04

Soil, investigation and testing ‐ Determination of grain‐size distri‐bution

DIN 18125‐1 2010‐07

Soil, investigation and testing ‐ Determination of density of soil ‐ Part 1: Laboratory tests

DIN 18125‐2 1999‐08/2011‐03*

Soil investigation and testing ‐ Determination of density of soil ‐ Part 2: Field tests (Edition 1999‐11 ‐ replaced)

DIN 18127 1997‐11/2012‐09*

Soil, investigation and testing ‐ Proctor‐test (Edition 1997‐11 ‐ replaced)

DIN 18128 1990‐11/2002‐12*

Soil ‐ Investigation and testing ‐ Determination of ignition loss (Edition 1990‐11 ‐ replaced)

DIN 18129 1996‐11/2010‐10/ 2011‐07*

Soil, investigation and testing ‐ Determination of lime content (Edition 1996‐11 und 2010‐10 ‐ replaced)



DIN 18130‐1 1998‐05

Soil ‐ investigation and testing ‐ Determination of the coefficient of water permeability ‐ Part 1: Laboratory tests

DIN 18132 1995‐12/2012‐04*

Soil, testing procedures and testing equipment ‐ Determination of water absorption (Edition 1995‐12 ‐ replaced)

DIN 18134 2012‐04*

Soil ‐ Testing procedures and testing equipment ‐ Plate load test (Edition 2001‐09 and 2010‐04 ‐ replaced)

DIN 19682‐1 2007‐11

Soil quality ‐ Field tests ‐ Part 1: Determination of soil colour

DIN 19682‐2 2007‐11/2013‐08/ 2014‐07*

Soil quality ‐ Field tests ‐ Part 2: Determination of soil texture(Edition 2007‐11 und 2013‐08 ‐ replaced)

GDA E 3‐12 (Nr. 3.6):2011 GDA‐Empfehlungen 3. Auflage 1997 S.268 Überarbeitung 4/2011

Acceptance test of mineral drainage layers para. 3.6 ‐ total carbonate content

2.4 Test methods (Investigation area II) by third party testing authorities for the installa‐tion mineral construction materials in landfill liner systems according to the Landfill Ordinance ‐ DepV and Federal Uniform Quality Standard BQS 9‐1

DIN EN 932‐1 1996‐11

Test for general properties of aggregates ‐ Part 1: Methods for sampling

DIN EN 932‐2 1999‐03

Test for general properties of aggregates ‐ Part 2: Methods for reducing laboratory samples


Tests for mechanical and physical properties of aggregates ‐ Part 5: Determination of the water content by drying in a venti‐lated oven

DIN EN 1097‐6 2005‐12/2013‐09

Tests for mechanical and physical properties of aggregates ‐ Part 6: Determination of particle density and water absorption (Edition 2005‐12 ‐ replaced)

DIN EN 1367‐1 2007‐06

Tests for thermal and weathering properties of aggregates ‐ Part 1: Determination of resistance to freezing and thawing

DIN 18122‐2 2000‐09

Soil ‐ investigation and testing ‐ Part 2: Determination of the shrinkage limit



DIN 18135 2011‐04/2012‐04

Investigation and testing ‐ Oedometer consolidation test (Edition 2011‐04 ‐ replaced)

DIN 18136 2003‐11

Soil ‐ Investigation and testing ‐ Unconfined compression test

DIN 18137‐2 1990‐12/2011‐04*

Soil, investigation and testing ‐ Determination of shear strength ‐ Part 2: Triaxial test (Edition 1990‐12 ‐ replaced)

DIN 18137‐3 2002‐09

Soil, investigation and testing ‐ Determination of shear strength ‐ Part 3: Direct shear test

DIN 4094‐2 1990‐12/2003‐05

Construction site ‐ tests in situ ‐ part 2: Standard Penetration Test (Edition 1990‐12 ‐ replaced)

Other applicable documents (for Investigation areas I and II) DIN EN 12620 2008‐07

Aggregates for concrete

DIN 18196 2006‐06/2011‐05*

Earthworks and foundation ‐ soil classification for civil engineering purposes (Edition 2006‐06 ‐ replaced)

*Previous editions already replaced new versions, but still remain as basis of BQS

2.5 Testing of bituminous construction materials DIN EN 12697‐20 2012‐06

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 20: Indentation using cube or cylindrical specimens


Technical testing of asphalt ‐ Part 20: Intrusion depth on cubic samples

DIN EN 12697‐27 2001‐04

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 27: sampling


Technical guidelines for bituminous mixtures ‐ Part 27: sampling



DIN EN 12697‐28 2001‐04

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 28: Preparation of samples for determining binder content, water content and grading


Technical test guidelines for bituminous mixtures ‐ Part 28: Preparation of samples

DIN EN 12697‐30 2012‐06

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 30: Specimen preparation by impact compactor


Technical test guidelines for bituminous mixtures ‐ Part 30: mak‐ing of test specimens with the impact compactor (MVG)

DIN EN 12697‐1 2012‐09

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 1: Soluble binder content


Technical test guidelines for bituminous mixtures ‐ Part 1: Soluble binder content

DIN EN 12697‐3 2013‐08

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 3: Bitumen recovery: Rotary evaporator


Technical test guidelines for bituminous mixtures ‐ Part 3: Bitu‐men recovery: Rotary evaporator

DIN EN 12697‐5 2010‐04

Technical test guidelines for bituminous mixtures Part 5: Deter‐mination of the maximum density


Technical test guidelines for bituminous mixtures ‐Part 5: Deter‐mination of the maximum density

DIN EN 12697‐6 2012‐07

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 6: Determination of bulk density of bituminous specimens


Technical test guidelines for bituminous mixtures ‐Part 6: Deter‐mination of bulk density of bituminous specimens

DIN EN 12697‐8 2003‐06

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 8: Determination of the air voids content of bituminous specimen


Technical test guidelines for bituminous mixtures ‐ Part 8: Deter‐mination of the air voids content of bituminous specimen and degree of compaction

DIN EN 12697‐2 2007‐11

Bituminous mixtures ‐ Test method for hot mix asphalt ‐ Part 2: Determination of particle size distribution




Technical test guidelines for bituminous mixtures ‐ Part 2: Deter‐mination of particle size distribution

DIN EN 12697‐35 2007‐10

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 35: Laboratory mixing


Technical test guidelines for bituminous mixtures ‐ Part 35: Labo‐ratory mixing

DIN EN 12697‐13 2001‐04

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 13: Temperature measurement


Technical test guidelines for bituminous mixtures – Part 13: Tem‐perature measurement

DIN EN 12697‐18 2004‐10

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 18: Binder drainage


Technical test guidelines for bituminous mixtures ‐ Part 18: Drain of stone mastic asphalt and porous asphalt

DIN EN 12697‐29 2002‐12

Bituminous mixtures ‐ Test method for hot mix asphalt ‐ Part 29: Determination of the dimensions of bituminous specimen


Technical test guidelines for bituminous mixtures ‐ Part 29: De‐termination of dimensions of bituminous specimen


Technical test guidelines for bituminous mixtures ‐ Part 80: Shear test

ÖNORM B 3639‐1 1997‐07

Asphalts for road construction and related purposes ‐ Testing ‐ Shear resistance in contact surfaces of asphalt layers

ÖNORM B 3639‐2 1997‐07

Asphalts for road construction and related purposes ‐ Testing ‐ Pull‐off‐resistance in contact surfaces of asphalt layers

ÖNORM EN 12697‐36 1997‐07

Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 36: Determination of the thickness of a bituminous pavement

DIN EN 1425 2012‐07

Bitumen and bituminous binders ‐ Characterisation of perceptible properties

DIN EN 1426 2007‐06

Bitumen and bituminous binders ‐ Determination of needle pene‐tration



E DIN EN 1426 2013‐09

Bitumen and bituminous binders ‐ Determination of needle pene‐tration

DIN EN 1427 2007‐06

Bitumen and bituminous binders ‐ Determination of the softening point ‐ Ring and Ball method

E DIN EN 1427 2013‐09

Bitumen and bituminous binders ‐ Determination of the softening point ‐ Ring and Ball method

DIN EN 13398 2010‐10

Bitumen and bituminous binders ‐ Determination of the elastic recovery of modified bitumen

DIN 52013 2007‐06

Bitumen and bituminous binders ‐ Determination of ductility

DIN EN 12594 2007‐06

Bitumen and bituminous binders ‐ Preparation of test samples

DIN EN 12594 2015‐01

Bitumen and bituminous binders ‐ Preparation of test samples

DIN EN 12607‐1 2013‐12

Bitumen and bituminous binders ‐ Determination of the resis‐tance to hardening under the influence of heat and air ‐ Part 1: RTFOT method

DIN EN 14769 2012‐08

Bitumen and bituminous binders ‐ Accelerated long‐term ageing conditioning by a Pressure Ageing Vessel (PAV)

DIN EN 14770 2012‐08

Bitumen and bituminous binders ‐ Determination of complex shear modulus and phase angle using a Dynamic Shear Rheome‐ter (DSR)

DIN EN 14771 2012‐08

Bitumen and bituminous binders ‐ Determination of the flexural creep stiffness ‐ Bending Beam Rheometer (BBR)

Multiple tress Creep and Recovery Test ‐ AL MSCR‐Prüfung (DSR) 2012

Guideline fort the determination of deformation of Bitumen and bituminous binders using a Dynamic Shear Rheometer (DSR) ‐ execution of MSCR‐test

2.6 Testing of road marking materials DIN EN 12802 2011‐12

Road marking materials ‐ Laboratory methods for identification



DIN EN 1436 2009‐01

Road marking materials ‐ Road marking performance for road users

DIN EN 1423 2013‐03

Road marking materials ‐ Drop on materials ‐ Glass beads, anti‐skid aggregates and mixtures of the two

DIN EN 1424 2003‐08

Road marking materials ‐ Premix glass beads

ZTV‐M 02 Teil 6.2.1 2002

Testing of height overhang , milling depth, milling width and milling length Examination of the amount supernatant

ZTV‐M 02 Teil 6.2.2 2002

Testing of drop on materials

ZTV‐M 02 Teil 6.2.3 2002

Testing of trafficability (drying time)

ZTV‐M 02 Teil 6.2.4 2002

Testing of day visibility

ZTV‐M 02 Teil 6.2.5 2002

Testing of night visibility

ZTV‐M 02 Teil 6.2.6 2002

Testing of skid resistance

ZTV‐M 02 Teil 6.2.7 2002

Testing of wear resistance (life time)

2.7 Testing of road equipment DIN EN 40‐3‐1 2013‐06

Lighting columns ‐ Part 3‐1: Design and verification ‐ Specifica‐tion for characteristic loads

EN 40‐3‐1 2013‐02

Lighting columns ‐ Part 3‐1: Design and verification ‐ Specifica‐tion for characteristic loads

DIN EN 40‐3‐2 2013‐06

Lighting columns ‐ Part 3‐2: Design and verification ‐ Verification by testing

EN 40‐3‐2 2013‐02

Lighting columns ‐ Part 3‐2: Design and verification ‐ Verification by testing



DIN EN 40‐3‐3 2013‐06

Lighting columns ‐ Part 3‐3: Design and verification ‐ Verification by calculation

EN 40‐3‐3 2013‐02

Lighting columns ‐ Part 3‐3: Design and verification ‐ Verification by calculation

2.8 Measuring the grip of surfaces DIN EN 13036‐4 2011‐12

Road and airfield surface characteristics ‐ Test methods ‐ Part 4: Method for measurement of slip/skid resistance of a surface ‐ The pendulum test

ARS 17/05 2005‐07

General circular Straßenbau No. 17/2005 ‐ Technical test guide‐lines for measurement of slip/skid resistance in road construc‐tion ‐ Part: Measuring method SRT (TP grip‐StB (SRT))

TP Griff‐StB 2004‐01

Technical test guidelines for measurement of slip/skid resistance in road construction ‐ Part: measuring method SRT (TP Griff‐StB (SRT))

2.9 Messung der Ebenheit von Oberflächen TP Eben ‐ Berührende Messungen 2007

Technical test guidelines for measurement of eveness on road surfaces in the longitudinal and transverse direction ‐ Part: Contact measurements

DIN EN 13036‐6 2008‐06

Road and airfield surface characteristics ‐ Test methods ‐ Part 6: Measurement of transverse and longitudinal profiles in the even‐ness and megatexture wavelength ranges

Applicable documents for monitoring and evaluation of road conditions and surfaces:

FGSV‐Nr. 490‐AP 9 2001/2003/2005/2008

Working documents for maintaining road condi‐tions



FGSV‐Nr. 490‐AP 9 2001/2003/2005/2008

Working documents for monitoring of road con‐ditions and‐evaluation (ZEB): Reihe M: measuring condition (edition 2001) Reihe V: Visual condition monitoring (edition 2001) Reihe A: Evaluation (edition 2001) Working documents for conserva‐tion/maintenance planning: Reihe R: computer aided conservation planning for rail track anchors (edition 2001) Reihe S: Substance values (stock) (edition 2003) Reihe K: communal requirements clause K 1:Principles

Unterabschnitt K 1.1: Principles for practical implementation of E EMI 2003 (2005) Unterabschnitt K 1.2: Order system and net description for local traffic surfaces (2005) Unterabschnitt K 1.3: data compilation (2008)

Unterabschnitt K 1.4: data organisation of his‐torigraphy (2008) Abschnitt K 2: recording of current status Unterabschnitt K 2.2: preparation and perform‐ance of visual inspection of local traffic surfaces (2005) Unterabschnitt K 2.3: damage catalogue for measuring and visual monitoring of current status (2005)

ZTV ZEB‐StB FGSV‐Nr. 998 2006

Additional technical contractual requirements and guidelines for status recording and evalua‐tion of roads

E EMI FGSV Regelwerk R 2 2012

Recommendations for conservation management of local roads



3 Mechanical structural test methods, testing of reinforcing steel as well as weld seams of metallic materials, dynamic testing of materials and structural components, corrosion and metallographic investigations

3.1 Tensile tests DIN EN ISO 4136 2013‐02

Destructive tests on welds in metallic materials ‐ Transverse tensile test

DIN EN ISO 5178 2011‐05

Destructive tests on welds in metallic materials ‐ Longitudinal ten‐sile test on weld metal in fusion welded joints

DIN EN ISO 6892‐1 2009‐12

Metallic materials ‐ Tensile testing ‐ Part 1: Method of test at room temperature (methode B)

DIN EN 1561 2012‐01

Founding ‐ Grey cast irons

DIN EN 10002‐1 2009‐12

Metallic materials ‐ Tensile testing ‐ Part 1: Method of test at room temperature (methode B) (withdrawn standard)


DIN EN 10164 2005‐03

Steel products with improved deformation proper‐ties perpendicular to the surface of the product ‐ Technical delivery conditions

DIN EN 12385‐1 2009‐01

Steel wire ropes ‐ Safety ‐ Part 1: General requirements

DIN EN ISO 14273 2002‐03

Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds

E DIN EN ISO 14273 2014‐07

Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds


DIN EN 895 1999‐05

Destructive tests on welds in metallic materials ‐ Transverse tensile test



DIN 50125 2004‐01

Testing of metallic materials ‐ Tensile test pieces

3.2 Impact and bending tests DIN EN ISO 148‐1 2011‐01

Metallic materials ‐ Charpy pendulum impact test ‐ Part 1: Test method

DIN EN ISO 5173 2012‐02

Destructive tests on welds in metallic materials ‐ Bend tests

DIN EN ISO 7438 2012‐03

Metallic materials ‐ Bend test

DIN EN ISO 8491 2004‐10

Metallic materials ‐ Tube (in full section) ‐ Bend test

DIN EN ISO 8492 2004‐10

Metallic materials ‐ Tube ‐ Flattening test

E DIN EN ISO 8492 2013‐06

Metallic materials ‐ Tube ‐ Flattening test

DIN EN ISO 8493 2004‐10

Metallic materials ‐ Tube ‐ Drift‐expanding test

DIN EN ISO 8494 2004‐10

Metallic materials ‐ Tube ‐ Flanging test

DIN EN ISO 8494 2014‐03

Metallic materials ‐ Tube ‐ Flanging test

DIN EN ISO 8495 2004‐10

Metallic materials ‐ Tube ‐ Ring‐expanding test

DIN EN ISO 8495 2014‐03

Metallic materials ‐ Tube ‐ Ring‐expanding test

DIN EN ISO 8496 2004‐10

Metallic materials ‐ Tube ‐ Ring tensile test

DIN EN ISO 8496 2014‐03

Metallic materials ‐ Tube ‐ Ring tensile test



DIN EN ISO 9016 2013‐02

Destructive tests on welds in metallic materials ‐ Impact tests ‐ Test specimen location, notch orientation and examination

DIN EN 10255 2007‐07

Non‐Alloy steel tubes suitable for welding and threading ‐ Technical delivery conditions

E DIN EN 10255 2010‐11

Non‐Alloy steel tubes suitable for welding, threading and other joining methods ‐ Requirements and test methods

DIN 50115 1991‐04

Testing of Metallic Materials ‐ Notched Bar Impact Bending Test Special samples and evaluation form (withdrawn standard)

DIN 50116 1982‐07

Testing of zinc and zinc alloys ‐ impact test


DIN EN 875 1995‐10

Destructive tests on welds in metallic materials ‐ Impact tests ‐ Test specimen location, notch orien‐tation and examination (withdrawn standard)

DIN EN ISO 9016 2011‐05

Destructive tests on welds in metallic materials ‐ Impact tests ‐ Test specimen location, notch orien‐tation and examination

DIN EN 910 1996‐05

Destructive test on welds in metallic materials ‐ Bend tests (withdrawn standard)

DIN EN ISO 5173 2010‐08

Destructive tests on welds in metallic materials ‐ Bend tests

3.3 Hardness tests DIN EN ISO 6506‐1 2006‐03

Metallic materials ‐ Brinell hardness test ‐ Part 1: Test method

DIN EN ISO 6506‐1 2015‐02

Metallic materials ‐ Brinell hardness test ‐ Part 1: Test method



DIN EN ISO 6507‐1 2006‐03

Metallic materials ‐ Vickers hardness test ‐ Part 1: Test method

DIN EN ISO 6508‐1 2006‐03

Metallic materials ‐ Rockwell hardness test ‐ Part 1: Test method Test methods (hardness scales A, B, C, D, E, F, G, H, K, N, T) (here: HRC)

E DIN EN ISO 6508‐1 2013‐04

Metallic materials ‐ Rockwell hardness test ‐ Part 1: Test method Test methods

The above listed standards are to be used in connection with the following

guidance documents:

DIN EN 1043‐1 1996‐02

Hardness testing ‐ Destructive tests on welds in metallic materials ‐ Part 1 ‐ Hardness test on arc welded joints ‐ (withdrawn standard)

DIN EN 1043‐2 2002‐04

Hardness test ‐ Destructive tests on welds in metallic materials ‐ Part 2: Micro hardness testing on welded joints (withdrawn standard)

DIN EN ISO 14271 2012‐11

Resistance welding ‐ Vickers hardness testing (low‐force and microhardness) of resistance spot, pro‐jection and seam welds

DIN EN ISO 9015‐1 2011‐05

Destructive tests on welds in metallic materials ‐ Hardness testing ‐ Part 1: Hardness test on arc welded joints

DIN EN ISO 9015‐2 2011‐05

Destructive tests on welds in metallic materials ‐ Hardness testing ‐ Part 2: Microhardness testing of welded joints

DIN EN 10328 2005‐04

Iron and steel ‐ Determination of the conventional depth of hard‐ening after surface heating



3.4 Non‐destructive testing of materials 3.4.1 Visual inspection DIN EN 17635 2011‐05

Non‐destructive testing of welds ‐ General rules for metallic mate‐rials

DIN EN 17637 2011‐05

Non‐destructive testing of welds ‐ Visual testing of fusion‐welded joints

3.4.2 Deformation measurement VdTÜV ‐Merkblatt 803 2008‐10

Guidelines for the implementation and evaluation of strain meas‐urements with stretch marks


VDI/VDE/GESA 2635 Blatt 1 2007‐04

Experimental structure analysis ‐ Metallic bonded resistance strain gages ‐ Characteristics and testing conditions

AD 2000‐Merkblatt S4 2000‐10

Review of tensions in computational and experi‐mental tension analysis

3.5 Testing of reinforcing steel DIN 488‐2 2009‐08

Reinforcing steel ‐ reinforcing steel bars

DIN 488‐3 2009‐08

Reinforcing steels ‐ Reinforcing steel in coils, steel wire

DIN 488‐4 2009‐08

Reinforcing steels ‐ Welded fabric

DIN 488‐5 2009‐08

Reinforcing steels ‐ Lattice girders

DIN EN 10080 2005‐08

Steel for the reinforcement of concrete ‐ Weldable reinforcing steel ‐ General

DIN EN ISO 15630‐1 2011‐02

Steel for the reinforcement and prestressing of concrete ‐ Test methods ‐ Part 1: Reinforcing bars, wire rod and wire



DIN EN ISO 15630‐2 2011‐02

Steel for the reinforcement and prestressing of concrete ‐ Test methods ‐ Part 2: Welded fabric

DIN EN ISO 17660‐1 2006‐12

Welding ‐Welding of reinforcing steel ‐ Part 1: Load‐bearing weldedjoints

DIN EN ISO 17660‐2 2006‐12

Welding ‐Welding of reinforcing steel ‐ Part 2: Non load‐bearing welded joints

3.6 Dynamic testing of materials and structural components DIN 4550 2004‐12

Office furniture ‐ Self‐supporting energized devices for the height adjustment of office work chairs ‐ Safety requirements, testing

DIN 50100 1978‐02

Testing of Materials ‐ Continuous Vibration Test ‐ Definitions, Symbols, Procedure, Evaluation

3.7 Other tests conducted within inspection programmes DIN EN 1057 2010‐06

Copper and copper alloys ‐ Seamless, round copper tubes for water and gas in sanitary and heating applications

DVGW GW 6 1996‐01

Capillary soldered fittings made of red brass and reducer fittings made of copper and red brass ‐ specifications and test requirements

DVGW GW 7 2002‐09

Brazing solder and flux for brazing of copper pipes for gas and water installations

DVGW GW 8 1996‐01

Capillary soldered fittings made of copper pipes ‐ specifications and test requirements

DVGW GW 392 2009‐07

Seamless drawn pipes made of copper for gas and water installa‐tions and internal galvanized pipes made of copper for gas and water installations ‐ Requirements and tests

DVGW VP 614 2013‐12

Permanent tube connections for metal gas pipes ‐ Press connect‐or

DVGW VP 652 2006‐05

Copper wire with firmly adhering plastic sheath for the drinking water installation



DVGW‐VP 617 1998‐07

Seamless drwan, internal galvanized pipes made of copper for water installations ‐ Requirements and testing assessments (only inspection)

DVGW‐W 534 2004‐05

Connectors for pipes and pipe connections for drinking water installation ‐ process sheet ‐

RAL‐RG 641/1 2009‐08

Quality and testing assesments (loads of performance) for the quality mark “Kupferrohr/RAL) of the Gütegemeinschaft Kupfer‐rohr e.V

RAL‐RG 641/2 2002‐10

Quality and testing assesments (loads of performance) for brazing solder and brazing flux in extension for the quality mark “Kupfer‐rohr/RAL) of the Gütegemeinschaft Kupferrohr e.V.

RAL‐RG 641/3 2000‐01

Quality and testing assesments (loads of performance) for soft solder and solder flux in extension for the quality mark “Kupfer‐rohr/RAL e.V.

RAL‐RG 641/4 2001‐04

Quality assurance of copper pipes Extension to capillary soldered fittings made of copper pipes ‐ Quality and testing assesments

SN 505262 2013‐01

Concrete construction (Testing of concrete steel)

SIA 262 2013‐01

Civil engineering (Testing of concrete steel)

3.8 Metalls and corrosion DIN EN ISO 945‐1 2010‐09

Microstructure of cast irons ‐ Part 1: Graphite classification by visual analysis

DIN EN ISO 1460 1995‐01

Metallic coatings ‐ Hot dip galvanized coatings on ferrous materi‐als ‐ Gravimetric determination of the mass per unit area

DN EN ISO 1461 2009‐10

Hot dip galvanized coatings on fabricazed iron and steels articles ‐ Specifications and test methods

DIN EN ISO 1463 2004‐08

Metallic and oxide coatings ‐ Measurement of coating thickness ‐ Microscopical method



DIN EN ISO 2178 1995‐04

Non‐magnetic coatings on magnetic substrates ‐ Measurement of coating thickness ‐ Magnetic method

DIN EN ISO 2360 2004‐04

Non‐conductive coatings on non‐magnetic electrically conductive basis materials ‐ Measurement of coating thickness ‐ Amplitude‐sensitive eddy current method

DIN EN ISO 3651‐1 1998‐08

Determination of resistance to intergranular corrosion of stainless steels ‐ Part 1: Austenitic and ferritic‐austenitic (duplex) stainless steels ‐ Corrosion test in nitric acid medium by meas‐urement of loss in mass (Huey test)

DIN EN ISO 3651‐2 1998‐08

Determination of resistance to intergranular corrosion of stainless steels ‐ Part 2: Ferritic, austenitic and ferritic‐austenitic (duplex) stainless steels ‐ Corrosion test in media containing sul‐furic acid

DIN EN ISO 6509 1995‐05

Corrosion of metals and alloys ‐ Determination of dezincification resistance of copper alloys with zinc

DIN EN ISO 6509 2014‐09

Corrosion of metals and alloys ‐ Determination of dezincification resistance of copper alloys with zinc

DIN EN ISO 7539‐1 2013‐04

Corrosion of metals and alloys ‐ Stress corrosion testing ‐ Part 1: General guidance on testing procedures

DIN EN ISO 2639 2003‐04

Steels ‐ Determination and verification of the depth of carburized and hardened cases

ISO 4967 2013‐07

Steel ‐ Determination of content of non‐metallic inclusions ‐ Micrographic method using standard diagrams

DIN EN 10328 2005‐04

Iron and steel ‐ Determination of the conventional depth of hard‐ening after surface heating

DIN 50190‐3 1979‐03

Hardness depth of heat‐treated parts ‐ determination of the effective depth of hardening after nitriding

DIN 50190‐4 1999‐09

Hardness depth of heat‐treated parts ‐ Part 4: Determination of the fusion hardening depth and the fusion depth

DIN EN ISO 3887 2003‐10

Steels ‐ Determination of depth of decarburization



DIN EN ISO 643 2013‐05

Steels ‐ Micrographic determination of the apparent grain size

DIN EN 10247 2007‐07

Micrographic examination of the non‐metallic inclusion content of steels using standard pictures

DIN 50600 1980‐03

Micrographic examination of the non‐metallic inclusion content of steels using standard pictures

DIN 50905‐2 1987‐01

Corrosion of metals ‐ corrosion testing ‐ corrosion characteristics under uniform corrosion attack

DIN 50905‐3 1987‐01

Corrosion of metals ‐ corrosion testing ‐ corrosion characteristics under nonuniform and localized corrosion attack without me‐chanical stress

DIN 50905‐4 1987‐01

Corrosion of metals ‐ corrosion testing ‐ corrosion testing in liq‐uids under laboratory conditions without mechanical stress

DIN 50915 1993‐09

Testing the resistance of unalloyed and low alloy steels to inter‐granular stress corrosion cracking by attack of nitrate medium ‐ welded and unwelded materials

DIN 50916‐1 1976‐08

Testing of copper alloys ‐ stress corrosion cracking test in ammo‐nia, testing of tubes, rods and profiles

DIN 50916‐2 1985‐09

Testing of copper alloys ‐ stress corrosion cracking test using ammonia ‐ testing of components

DIN 54150 1977‐08

Non‐destructive testing ‐ impression methods for surface exami‐nation (Replica‐technique)

DVGW GW 2 2012‐05

DVGW‐system of rules – Connections of copper pipes for gas and water installations inside of estates and buildings

DVGW GW 541 2004‐10

Pipes made of non‐corroding steels and titan for drinking water installations ‐ Requirements and testing


DIN EN ISO 5817 2006‐10

Welding ‐ Fusion‐welded joints in steel, nickel, titanium and their alloys (beam welding ex‐cluded) ‐ Quality levels for imperfections



DIN EN ISO 5817 2012‐06


DIN EN ISO 6520‐1

2007‐11

Welding and allied processes ‐ Classification of geometric imperfections in metallic materials ‐ Part 1: Fusion welding

DIN EN ISO 18265 2014‐02

Metallic materials ‐ Conversion of hardness values

DIN 50600 1980‐03

Testing of metallic materials ‐ Metallographic Micrographs ‐ Picture scales and formats

DIN 50905 Teil 1 2009‐09

Corrosion of metals ‐ Corrosion testing ‐ Part 1: General guidance

DIN EN 12502‐1 2005‐03

Protection of metallic materials against corrosion ‐ Guidance on the assessment of corrosion likeli‐hood in water distribution and storage systems ‐ Part 1: General

DIN EN 12502‐2 2005‐03

Protection des matériaux métalliques contre la corrosion ‐ Recommandations pour l'évaluation du risque de corrosion dans les installations de distribution et stockage d'eau ‐ Partie 2: Facteurs à considérer pour le cuivre et les alliages de cuivre

DIN EN 12502‐3 2005‐03

Protection of metallic materials against corrosion ‐ Guidance on the assessment of corrosion likeli‐hood in water distribution and storage systems ‐ Part 3: Influencing factors for hot dip galvanised ferrous materials

DIN EN 12502‐4 2005‐03

Protection of metallic materials against corrosion ‐ Guidance on the assessment of corrosion likeli‐hood in water distribution and storage systems ‐ Part 4: Influencing factors for stainless steels

DIN EN 12502‐5 2005‐03

Protection of metallic materials against corrosion ‐ Guidance on the assessment of corrosion likeli‐hood in water distribution and storage systems ‐ Part 5: Influencing factors for cast iron, unalloyed and low alloyed steels

VDI 3822 2011‐11

VDI‐Guidance, Failure analysis ‐ Fundamentals and performance of failure analysis



VDI 3822 Blatt 2 2008‐04

Failure analysis ‐ failures caused by mechanical‐working conditions

VDI 3822 Blatt 3 2007‐03

Failure analysis ‐ Failures caused by corrosion in electrolytes

VDI 3822 Blatt 1.4 2011‐10

Failures caused by thermal loading

3.9 Welding tests DIN EN 1320 1996‐12

Destructive tests on welds in metalllic materials ‐ Fracture test (withdrawn standard)

DIN EN ISO 9017 2013‐12

Destructive tests on welds in metallic materials ‐ Fracture test

DIN EN 13916 1996‐11

Welding ‐ Guidance on the measurement of preheating tempera‐ture, interpass temperature and preheat maintenance tempera‐ture

DIN EN 14555 2006‐12

Welding ‐ Arc stud welding of metallic materials

DIN EN 14555 2014‐08

Welding ‐ Arc stud welding of metallic materials


DIN EN 287‐1 2006‐06

Qualification testing of welders ‐ Fusion welding ‐ Part 1: Steels (withdrawn standard)

DIN EN ISO 9606‐1

2013‐12

Qualification testing of welders ‐ Fusion welding ‐ Part 1: Steels

DIN EN 287‐6 2010‐05

Qualification test of welders ‐ Fusion welding ‐ Part 6: Cast iron

DIN EN ISO 9606‐2 2005‐03

Qualification test of welders ‐ Fusion welding ‐ Part 2: Aluminium and aluminium alloys

DIN EN ISO 9606‐3

1999‐06 Approval testing of welders ‐ Fusion welding ‐ Part 3: Copper and copper alloys

DIN EN ISO 9606‐4

1999‐06 Approval testing of welders ‐ Fusion welding ‐ Part 4: Nickel and nickel alloys



DIN EN ISO 17660‐1 2006‐12

Welding ‐ Welding of reinforcing steel ‐ Part 1: Load‐bearing welded joints

DIN EN ISO 17660‐2 2006‐12

Welding ‐ Welding of reinforcing steel ‐ Part 2: Non load‐bearing welded joints

DIN EN ISO 15607

2004‐03 Specification and qualification of welding proce‐dures for metallic materials ‐ General rules

DIN EN ISO 17637 2011‐05

Non‐destructive testing of welds ‐ Visual testing of fusion‐welded joints

DIN 1418 1998‐01

Welding personnel ‐ Approval testing of welding operators for fusion welding and resitance weld setters for fully mechanized and automatic weld‐ing of metallic materials (withdrawn standard)

DIN EN ISO 14732 2013‐12

Welding personnel ‐ Qualification testing of weld‐ing operators and weld setters for mechanized and automatic welding of metallic materials

DIN EN 15085‐3 2010‐01

Railway applications ‐ Welding of railway vehicles and components ‐ Part 3: Design requirements

DIN EN 15085‐5 2008‐01

Railway applications ‐ Welding of railway vehicles and components ‐ Part 5: Inspection, testing and documentation

DIN 18808 1984‐10

Steel structures ‐ structures made from hollow sections subjected to predominantly static load‐ing (withdrawn standard)

DIN EN 1993‐1‐1 2010‐12

Eurocode 3: Design of steel structures ‐ Part 1‐1: General rules and rules for buildings

DIN EN ISO 13919‐1 1996‐09

Welding ‐ Electrons and laser beam welded joints ‐ guidance on quality levels for imperfections ‐ Part 1: Steel

DIN EN ISO 5817 2006‐10




DIN EN ISO 5817 2014‐06


DIN EN ISO 6520‐1 2007‐07

Welding and allied processes ‐ Classification of geometric imperfections in metallic materials ‐ Part 1: Fusion welding

DIN EN ISO 6520‐2 2002‐04

Welding and allied processes ‐ Classification of geometric imperfections in metallic materials ‐ Part 2: Welding with pressure

DIN EN ISO 10042 2006‐02

Welding ‐ Arc‐welded joints in aluminium and its alloys ‐ Quality levels for imperfections

DVS‐Richtlinie 1702 2009‐09

Procedure test at construction engineering

DVS‐IIW/EWF Richtlinie 1111‐1 2013‐07

International welder ‐ minimum requirements on training,testing and qualification ‐ Part I: general information, conditions, subject synopsis

DVS‐IIW/EWF Richtlinie 1111‐2 2013‐07

International welder ‐ minimum requirements on training,testing and qualification ‐ Part II: Rules and guidance for test objects

Richtlinie 97/23/EG 1997‐05

Directive of European Parliament and Council dated 27.05.1997 approximation of the laws oft he member states concerning pressure equip‐ment

AD 2000‐Merkblatt HP 32007‐02

Welding supervision, welders

TRD 201 1998‐06

Technical regulations for steam boilers Production welding of steel components Production ‐ Testing



DIN EN ISO 17660‐1 2006‐12 + Corrigenda 1 2007‐08

Welding ‐ Welding of reinforcing steel ‐ Part 1: Load‐bearing welded joints

DIN EN ISO 17660‐2 2006‐12+ Corrigenda 1 2007‐08

Welding ‐ Welding of reinforcing steel ‐ Part 2: Non‐load‐bearing welded joints

DIN EN ISO 15614‐1 2005‐03

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys

DIN EN ISO 15614‐2 2005‐07

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 2: Arc welding of aluminium and its alloys

DIN EN ISO 15614‐3 2008‐06

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 3: Fusion welding of non‐alloyed and low‐alloyed cast irons

DIN EN ISO 15614‐4 2005‐09+ Corrigenda 1 2008‐01

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 4: Finishing welding of aluminium castings

DIN EN ISO 15614‐5 2004‐07

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 5: Arc welding of titanium, zirconium and their alloys

DIN EN ISO 15614‐6 2007‐01

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 6: Arc and gas welding of copper and its alloys

DIN EN ISO 15614‐7 2007‐09

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 7: Overlay welding



E DIN EN ISO 15614‐7 2013‐10

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 7: Overlay welding

DIN EN ISO 15614‐8 2002‐06

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 8: Welding of tubes to tube‐plate joints

E DIN EN ISO 15614‐8 2014‐02

Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 8: Welding of tubes to tube‐plate joints

DIN 2303 2007‐02

Welding and allied processes ‐ Quality require‐ments for production and maintenance compa‐nies for military products

DIN EN ISO 25239‐1 2012‐03

Friction stir welding ‐ Aluminium ‐ Part 1: Vo‐cabulary

DIN EN ISO 25239‐2 2012‐03

Friction stir welding ‐ Aluminium ‐ Part 2: Design of weld joints

DIN EN ISO 25239‐3 2012‐03

Friction stir welding ‐ Aluminium ‐ Part 3: Qualifi‐cation of welding operators

DIN EN ISO 25239‐4 2012‐03

Friction stir welding ‐ Aluminium ‐ Part 4: Specifi‐cation and qualification of welding procedures

DIN EN ISO 25239‐5 2012‐03

Friction stir welding ‐ Aluminium ‐ Part 5: Quality and inspection requirements

DIN EN ISO 3834‐1 2006‐03

Quality requirements for fusion welding of metal‐lic materials ‐ Part 1: Criteria for the selection of the appropriate level of quality requirements

DIN EN ISO 3834‐2

2006‐03 Quality requirements for fusion welding of metal‐lic materials ‐ Part 2: Comprehensive quality requirements

DIN EN ISO 3834‐3 2006‐03

Quality requirements for fusion welding for me‐tallic materials ‐ Part 3: Standard quality re‐quirements



DIN EN ISO 3834‐4 2006‐03

Quality requirements for fusion welding of metal‐lic materials ‐ Part 4: Elementary quality re‐quirements

DIN EN ISO 3834‐5 2006‐03 + Corrigenda 1 2009‐04

Quality requirements for fusion welding of metal‐lic materials ‐ Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements

E DIN EN ISO 3834‐5 2014‐02

Quality requirements for fusion welding of metal‐lic materials ‐ Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements

DIN EN 1090‐1 2012‐02

Execution of steel structures and aluminium structures ‐ Part 1: Requirements for conformity assessment of structural components

DIN EN 1090‐2 2011‐10

Execution of steel structures and aluminium structures ‐ Part 2: Technical requirements for steel structures

DIN EN 1090‐3 2008‐09

Execution of steel structures and aluminium struc‐tures ‐ Part 3: Technical requirements for alumin‐ium structures



4 Testing of construction products and testing of fire resistance within the framework of Regulation (EU) No. 305/2011 laying down harmonised conditions for the marketing of construction products (Construction Products Regulation ‐ CPR)

Decision / Resolution of the Commission

System1) Technical Specification

1995/467/EC Gypsum products

3

EN 520:2004 + A1:2009 Gypsum plasterboards ‐ Definitions, requirements and test method

EN 14195:2005/AC:2006 Metal framing components for gypsum board systems ‐ Defi‐nitions, requirements and test methods

1997/176/EC Products from structural timber

3 EN 14592:2008 + A1:2012 Timber structures ‐ Dowel‐type fasteners ‐ Requirements

1997/464/EC/ 2004/663/EC Products for sanitation outside buildings

3

EN 1433:2002 + A1:2005 Drainage channels for vehicular and pedestrian areas ‐ Classi‐fication, design and testing requirements, marking and evaluation of conformity

1997/740/EC Masonry and related products

3

EN 845‐1:2003 + A1:2008 Specification for ancillary components for masonry ‐ Part 1: Wall ties, tension straps, hangers and brackets

EN 845‐2:2003 Specification for ancillary components for masonry ‐ Part 2: Lintels

EN 845‐3:2003 + A1:2008 Specifications for ancillary components for masonry ‐ Part 3: Bed joint reinforcement of steel meshwork

1997/808/EC Flooring

3

EN 13454‐1:2004 Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate ‐ Part 2: Test methods

1998/213/EC Internal partition kits

3

ETAG 003:1999 Guideline for European technical approval for internal parti‐tion kits use as non‐loadbearing walls

1998/437/EC Wall and ceiling finishes for internal and external areas

3 EN 13964:2004 + A1:2006 Suspended ceilings ‐ Requirements and test methods



Decision / Resolution of the Commission

System1) Technical Specification

1999/91/EC thermal insulating pro‐ducts

3

EN 14316‐1:2004 Thermal insulation products for buildings ‐ In‐situ thermal in‐sulation formed from expanded perlite (EP) products ‐ Part 1: Specification for bonded and loose‐fill products before instal‐lation

1999/470/EC Construction adhesives

3

EN 12004:2007 + A1:2012 Adhesives for tiles ‐ Requirements, evaluation of conformity, classification and designation

1999/472/EC

pipes, tanks and ancillar‐ies not in contact with water intended for hu‐man consumption

3

EN 1057:2006 + A1:2010 Copper and copper alloys ‐ Seamless, round copper tubes for water and gas in sanitary and heating applications EN 10255:2004 + A1:2007 Non‐alloy steel tubes suitable for welding and threading‐ Technical delivery conditions

1) System for the assessment and verification of constancy of performance

The requirements for a testing labaratory according to article 43 of regulation (EU) 305/2011 laying down harmonised conditions for the marketing of construction are fulfilled. Test proce‐dures for which a determination of the product type is needed and which will not be car‐ried out by the holder of this certificate are named in a list of subcontractors. Abbreviations used:

DAfStB German Committe for reinforcing steel DIBt Competence Centre for Construction DGGT German Society for Earth and Foundation Works DIN German Institute for Standardisation DVGW German Association of Gas and Water Experts EN European Standard FGSV Research Society for Roads and Traffic Engineering GDA E 3‐12

Recommendation for geotechnical acceptability: E 3‐12 Acceptability of mineral drainage layers

ISO International Organisation for Standardisation ÖNORM Austrian Standard RAL German Institute for Quality Control and Labelling TP Asphalt ‐ St B Technical test specification for Asphalt TP Gestein ‐ StB Technical test specification for aggregates in road works VDI Association of German Engineers ZEB Status monitoring and evaluation of tracks surfaces of roads ZTV Asphalt ‐ StB 07 Additional technical contractual conditions and guidelines for construction

of asphalt traffic surfaces ZTV‐SIB Additional technical contractual conditions and guidelines for protection

and restoration of concrete structural components QMA x.x.xxx Work Instruction of TÜV Rheinland LGA Bautechnik GmbH