Glands_Accessories LSF.pdf

8/13/2019 Glands_Accessories LSF.pdf

1/44


2/44

12:2

12

Glands

Cable glands are designed to provide some or all of the following functions in a cabling system:

Mechanical connection: Locate and anchor cable. Earth continuity: Armour termination.

Ingress Protection: Protect against dust and liquids.

Hazardous area: Flameproof protection.

The design of cable glands are covered by BS6121, which covers size, finish, materials,

performance, etc. The gland designs are basically a combination of compatibility with cable and

installation requirements.

GLAND TYPES

There are several distinct gland types covered in BS6121 Part 1;

A Type

B Type

C Type

D1 Type

E1 Type

D2 Type

E2 Type

Suffixes are used to identify the type of armour on a cable:

W = single wire armour

X = wire braid armour

Y = aluminium wire armour

Z = steel tape armoured

Hence, CW would be a single wire armour, whereas CX would be for a braid armour. The only

difference is in the armour lock which caters for the physical size of the armour.

ACCESSORIES


3/44

12

ACCESSORIES

12:3

Gland Type Application/Use

A1/A2 Indoor/outdoor brass gland for use with unarmoured cable.

BW Indoor, low-cost, two-part brass gland for use with single wire armoured cable.

CW Indoor/outdoor brass glands for use with single wire armoured cable.

Provides seal on outer sheath of cable and separate armour locking ring.

NB: Aluminium gland available for aluminium wire armoured cable.

CX Indoor/outdoor brass gland for use with braid armoured cables. Provides

seal on outer sheath of cable and separate armour locking ring.

E1W Indoor/outdoor brass gland for use with single wire armour cable. Provides

seal on inner and outer sheaths of cable, and has separate armour locking ring.

LSF Glands

BW Indoor, low cost, two-part brass gland for use with LSF single wire

armoured cables.

CW Indoor/outdoor brass gland for use with LSF single wire armoured cables.

Provides LSF seal onto outer sheath of cable and separate armour locking ring.

Glands for Hazardous Areas

A2F Indoor/outdoor brass gland for use with unarmoured cables. For use with

flameproof or increased safety equipment (E.Exd or E.Exe)

E1WF Indoor/outdoor brass gland for use with single wire armoured cable.Provides seal on inner and outer sheaths of cable, and has separate locking

ring. For use with flameproof or increased safety equipment (E.Exd or E.Exe)

E1XF Indoor/outdoor brass gland for use with braid armoured cable. Provides

seal on inner and outer sheaths of cable, and has separate armour locking

ring. For use with flameproof or increased safety equipment (E.Exd or E.Exe).

E2WF Indoor/outdoor brass gland for use with single wire armoured and lead

sheathed cables (eg. EEMUA types, BS5308 PT1/Type 3). Provides seal

onto outer sheath of cable. Inner seal grips and provides earth continuity to

lead sheath. Design has separate armour locking ring. For use withflameproof or increased safety equipment (E.Exd or E.Exe).

BARR-X Indoor/outdoor brass barrier gland for use with a braid armoured cable.

Provides seal on outer sheath of cable, and solid setting compound

squeezed into the interstices of cable when installed to prevent escape of

gases through centre of cable. For use with explosion proof equipment.


4/44

12:4

12

I.P Ratings for Cable Glands

I.P. (Ingress Protection) Ratings detail the degree of protection against solid

bodies and liquids, and is tested against IEC 144.

Generally any seal has a rating of IP66.

However, since they are tested in isolation, when they are in conjunction with a

piece of equipment this needs to be taken into consideration.

Generally the following can be taken:-

1. Gland used in Plain Entry with Backnut - IP54.

2. Gland used in Plain Entry with sealing washer between gland and equipment

interface - IP66.

3. Gland used in Tapped Entry - IP65.

4. These can be uprated by the use of Sealing washers and Thread Sealants.

5. Special designs of Gland are available which can achieve an IP Rating of

IP68. (NB. Interface with equipment then becomes critical.)

ACCESSORIES


5/44

12

12:5

Degree of Protection IEC 144 I.P. Ratings

First ProtectionDigit (Against solid bodies)

0 No protection

1 Protected against solid bodies larger than 50mm, eg, accidentalcontact with hand.

2 Protected against solid bodies larger than 12mm, eg, finger.

3 Protected against solid bodies larger than 2.5mm, eg, tools and wires.

4 Protected against solid bodies larger than 1.0mm, eg, fine tools andsmall wires.

5 Protected against dust (no harmful deposits).

6 Completely protected against dust.

Second ProtectionDigit (Against Liquids)

0 No protection.

1 Protected against vertically falling drops of water (condensation).

2 Protected against drops of water falling at up to 150 from the vertical.

3 Protected against rain falling at 600 from vertical.

4 Protected against splashes of water from all directions.

5 Protected against jets of water from all directions.

6 Protected against jets of water of similar force to heavy seas.

7 Protected against the effects of temporary immersion.

8 Protected against prolonged effects of immersion under pressure.

ACCESSORIES


6/44

12:6

12

A1/A2 Brass Gland with Outer Seal

To BS6121: Part 1.

Suitable for unarmoured, plastic orrubber sheathed cables.

Suitable for most indoor and outdoor

applications.

Seal rated to IP66

Glands are supplied in kit form, complete with locknuts and shrouds.

Up to size 25:- 2 per kit

Size 32 and above:- 1 per kit

CABLE & GLAND DETAILS

E1AW-A1/A2-20SS Pirelli 20SS 3.5 8.5

E1AW-A1/A2-20S Pirelli 20S 8.0 11.5

E1AW-A1/A2-20 Pirelli 20 11.0 13.5

E1AW-A1/A2-25 Pirelli 25 13.0 19.5

E1AW-A1/A2-32 Pirelli 32 19.0 25.5

E1AW-A1/A2-40 Pirelli 40 25.0 32.0

E1AW-A1/A2-50S Pirelli 50S 31.5 37.0

E1AW-A1/A2-50 Pirelli 50 36.5 43.0

E1AW-A1/A2-63S Pirelli 63S 42.5 50.0

Anixter Gland Gland Cable dimensionsPart No. Manu Size accomodated

Overall diameterMin Max

ACCESSORIES


7/44

12

12:7

CX Brass Gland with Outer Seal

BS6121: Part 1

Suitable for wire braid armoured, plastic or rubber

sheathed cables.

Outer seal grips sheath of cable.

Weatherproof and water proof.

Seal rated to IP66.

Design has separate armour locking ring.

Gland rated to IP66 with use of suitable sealing

washer or thread sealant at gland interface

Glands are supplied in kit form, complete with locknuts, earthtags and shrouds.




Anixter Gland Gland Cable dimensions

Part No. Manu Size accomodated

Under armour Overall

Min Max Min Max

E1AH-CX-20SS Pirelli 20SS - 8.6 8.0 13.2

E1AH-CX-20S Pirelli 20S - 11.6 8.0 15.8

E1AH-CX-20 Pirelli 20 - 13.9 12.9 20.8

E1AH-CX-25 Pirelli 25 - 19.9 17.0 27.2

E1AH-CX-32 Pirelli 32 - 26.2 23.5 33.5

E1AH-CX-40 Pirelli 40 - 32.1 29.0 39.9

ACCESSORIES


8/44

ACCESSORIES

12:8

12

CXT Brass Gland with Outer Seal

Gland reference not specified in BS6121:Part 1. However, gland complies in

all other respects with the design and test requirements of Type A2 cable glands.

Suitable for wire braid armoured/screened, plastic or rubber sheathed cables. Outer seal grips sheath of cable.


Seal rated to IP66.

Integral knurled armour lock.


washer or thread sealant at gland interface

Glands are supplied in kit form, complete with locknuts, earthtags and shrouds.






Overall

Min Max

E1AH-CXT-20S CMP 20S 6.1 11.6

E1AH-CXT-20 CMP 20 6.5 13.9

E1AH-CXT-25 CMP 25 11.1 19.9

E1AH-CXT-32 CMP 32 17.0 26.2

E1AH-CXT-40 CMP 40 22.0 32.1


9/44

12:9

12

ACCESSORIES

Ultech Nylon Gland with Outer SealFor non-armoured cable

Suitable for unarmoured, plastic or rubber sheathed cables.

Polyamide 6 nylon gland with neoprene seal.

Compact skin-top design

Quick and easy assembly

Halogen free and UL94-V2 flammability rated.

Seal rated IP68 at 5 bar.

Temperature range: -30C to +80C

Grey RAL 7001 colour

ISOMETRIC thread.

10mm thread length for gland sizes 16-25, 18mm for gland size 32.

Ultech is a registered trade name of Elkay International

Glands are supplied in kit form, complete with nylon washer and locknut. Allsizes: 2 per kit.

NB: Mini-size polyamide 6.6 standard nylon gland is also available for IP66 ratednitrile seal for small diameter cable. Details as follows:-


E1AV-ULT-16 Elkay 270-8011 16 5.0 10.0

E1AV-ULT-20S Elkay 270-8021 20S 6.0 12.0

E1AV-ULT-20 Elkay 270-8031 20 10.0 14.0

E1AV-ULT-25 Elkay 270-8061 25 13.0 18.0

E1AV-ULT-32 Elkay 270-8071 32 18.0 25.0

Anixter Part Gland Gland Manf. Gland Size Cable DimensionsNumber Manf. Part Number accommodated (mm)

Overall diameter

Minimum Maximum


10/44

ACCESSORIES

12:10

12

Mini - Gland


-20C to +90C temperature range. Grey RAL 7001 colour.

ISOMETRIC thread.

8mm thread length.

Glands are supplied in kit form with nylon washer and locknut 2 per kit.


E1AV-MINI-13 Elkay 239-B M13 2.0 5.0

Anixter Part Gland Gland Manf. Gland Size Cable Dimensions

Number Manf. Part Number accommodated (mm)Overall diameter

Minimum Maximum


11/44

12

ACCESSORIES

12:11

LSF Standard Cable Gland forNon-Armoured Cable

Suitable for unarmoured plastic or rubber sheathed cables.

Polyamide 6.6 nylon gland with nitrile rubber seal.

Quick and easy assembly.


Seal rated at IP66.

-20C to +90C temperature range.

Black RAL 9005 colour.

ISO METRIC thread. 11mm thread length

LSF glands meet following standards:- BS6853 App B5.1, BS7878, BS2782

M141, IEC 60754-1, IEC 60754-2, BS6425, NES713/Iss 3.

Glands are supplied in kit form, complete with washer and locknut.


E1AV-LSF-20SS Elkay 249-LSF 20SS 4.0 6.0

E1AV-LSF-20S Elkay 251-LSF 20S 7.0 10.0

E1AV-LSF-20 Elkay 252-LSF 20 8.0 13.0

Anixter Part Gland Gland Manf. Gland Size Cable DimensionsNumber Manf. Part Number accommodated (mm)

Overall diameterMinimum Maximum


12/44

ACCESSORIES

12:12

12

TECHNICAL DATA

ASTM Oil No. 2 SAcetaldehyde LAcetic acid (10%) L

Acetic acid (glacial) LAcetone SAmmonium Hydroxide (35%) SBenzene SBenzyl Alcohol LBromine (liquid) UButyl Alcohol SButyl Acetate SButylamine SCarbon Tetrachloride SChlorine Gas UCitric acid (10%) SCresols UCyclohexane SDiesel oil SDiethyl ether SEthanol SEthylamine LEthylene glycol SFormaldehyde SHexane SHydrochloric acid (10%) UHydrochloric acid (conc) UHydrogen peroxide (35%) L

Chemical Agent Nylon

Hydrogen sulphide (gas) SIso-octane SIso-propanol S

Lubricating oil SMethanol LNitric acid (10%) UNitric acid (conc) UOzone (gas) LParaffin oil SPetrol SPhenol USilicone oils SSodium hydroxide (60%) SSodium hypochlorite (bleach) LStyrene SSulphur dioxide (gas) USulphuric acid (10%) USulphuric acid (70%) UToluene STransformer oil STrichloroethylene LTricresyl phosphate (SKYDROL) STurps SWhite spirit SXylene SZinc chloride U

Chemical Agent Nylon

APPLICABLE TO NYLON GLANDS - CHEMICAL

RESISTANCE

Listed below is the general chemical resistance

information for the materials used to manufacture themajority of products in this catalogue.S = SuitableL = Limited suitability

U = Unsuitable


13/44

12

ACCESSORIES

12:13

Index EMC Nickel Plated Brass Gland forBraid Screened Cable

12

3

456

FEATURES.

1. Compression Nut

2. Santoprene Seal

3. Endless Spring

4. Tapered Ring

5. O Ring

6. Gland Body

For use with braid screened cable to connect screen to the enclosure system.

Two tapered rings applying force onto an endless spring washer ensure positive

and intimate contact for efficient screening.

Screen can continue into enclosure.

Suitable for systems conforming to EN50082.

Nickel plated brass gland body with santoprene rubber seal.

Seal rated IP68 at 1 bar.

-40 to +135C temperature range. ISO METRIC thread with exception of gland for 4-6mm diameter cable which has

P.G.7 thread to DIN40430.

Glands are supplied in kit form complete with locknut. All sizes: 2 per kit.

E1AH-EMC-7 Elkay 261-1000 PG7 1.5 4.0 4.0 6.0

E1AH-EMC-16 Elkay 260-1000 M16 3.0 7.0 6.0 8.0

E1AH-EMC-20 Elkay 260-1250 M20 4.0 8.5 8.0 10.5

E1AH-EMC-25SSS Elkay 260-1400 M25 6.5 10.0 10.0 11.5

E1AH-EMC-25SS Elkay 260-1450 M25 8.0 12.0 11.0 14.0

E1AH-EMC-25S Elkay 260-1500 M25 8.0 12.0 14.0 16.6

E1AH-EMC-25 Elkay 260-1600 M25 12.5 17.5 17.0 20.0

E1AH-EMC-32S Elkay 260-1650 M32 15.0 21.0 19.0 23.0

E1AH-EMC-32 Elkay 260-1700 M32 15.0 21.0 22.0 27.0

Anixter Part No. Gland Gland Gland Cable Dimensions Accommodated (mm)

Manf. Manf. Part Size Over Screen Cable Diameter

No. Min. Max. Min. Max.


14/44

ACCESSORIES

2:14

12

CW Brass Gland with Outer Seal

BS6121: Part 1

Suitable for wire armoured, plastic or rubber

sheathed cables.



Seal rated to IP66.

Design has separate armour locking ring (Pirelli glands only).

Gland rated to IP66 with use of suitable

sealing washer or thread sealant at gland

interface

Brass glands are provided with steel locknuts and aluminium glands are provided

with aluminium locknuts. For more corrosive environments brass locknuts may

be supplied.

Glands are supplied in kit form complete with locknuts, earthtags and shrouds.

Pirelli Up to size 25: - 2 per kit


CMP Up to size 32:- 2 per kit



15/44

12

ACCESSORIES

12:15


E1AG-CW-20SSC Pirelli 20SS - 8.6 8.0 13.2

E1AG-CW-20SS CMP 20SS* - 8.6 8.0 13.4

E1AG-CW-20SC Pirelli 20S - 11.6 8.0 15.8

E1AG-CW-20S CMP 20S - 11.6 11.4 15.9

E1AG-CW-20C Pirelli 20 - 13.9 12.9 20.8

E1AG-CW-20 CMP 20 - 13.9 15.0 20.9

E1AG-CW-25C Pirelli 25 - 19.9 17.0 27.2

E1AG-CW-25 CMP 25 - 19.9 20.3 27.4

E1AG-CW-32C Pirelli 32 - 26.2 23.5 33.5

E1AG-CW-32 CMP 32 - 26.2 26.0 33.9

E1AG-CW-40C Pirelli 40 - 32.1 29.0 39.9

E1AG-CW-40 CMP 40 - 32.1 31.0 40.4

E1AG-CW-50SC Pirelli 50S - 38.1 38.0 46.2

E1AG-CW-50S CMP 50S - 38.1 36.5 46.7

E1AG-CW-50C Pirelli 50 - 44.0 39.5 52.6

E1AG-CW-50 CMP 50 - 44.0 43.0 53.1

E1AG-CW-63S CMP 63S - 50.0 48.9 59.4

E1AG-CW-63C Pirelli 63 - 55.9 51.3 65.3

E1AG-CW-63 CMP 63 - 55.9 58.0 65.9

E1AG-CW-75C Pirelli 75 - 67.9 62.5 78.0

E1AG-CW-75 CMP 75 - 67.9 64.9 78.5

Aluminium CW glands for aluminium wire armoured cable

E1DN-CW-25 Pirelli 25 - 19.9 17.0 27.2

E1DN-CW-32 Pirelli 32 - 26.2 23.5 33.5E1DN-CW-40 Pirelli 40 - 32.1 29.0 39.9

E1DN-CW-50SC CMP 50S - 38.1 36.5 46.7

E1DN-CW-50 Pirelli 50 - 44.0 39.5 52.6




Min Max Min Max

NB Pirelli glands have separate armour locking rings.CMP glands have integral knurled armour lock.

* Also known as 20/16 (CMP only),


16/44

ACCESSORIES

2:16

12

BW Brass Gland

BS6121: Part 1

Suitable for single wire armoured,

plastic or rubber sheathed cables. For use in dry, indoor situations.

Low-cost two-part design.

IP54

Shroud may be used for additional

ingress protection


Pirelli Up to size 25: - 2 per kit


CMP Up to size 32:- 2 per kitSize 40 and above:- 1 per kit


E1AJ-BW-20SC Pirelli 20S - 11.6 - 15.8

E1AJ-BW-20S CMP 20S - 11.6 - 16.1

E1AJ-BW-20C Pirelli 20 - 13.9 - 20.8

E1AJ-BW-20 CMP 20 - 13.9 - 21.1

E1AJ-BW-25C Pirelli 25 - 19.9 - 27.2

E1AJ-BW-25 CMP 25 - 19.9 - 27.4

E1AJ-BW-32C Pirelli 32 - 26.2 - 33.5

E1AJ-BW-32 CMP 32 - 26.2 - 34.4

E1AJ-BW-40C Pirelli 40 - 32.1 - 39.9

E1AJ-BW-40 CMP 40 - 32.1 - 42.4

E1AJ-BW-50S CMP 50S - 38.1 - 50.1

E1AJ-BW-50C Pirelli 50 - 44.0 - 52.6

E1AJ-BW-50 CMP 50 - 44.0 - 55.7E1AJ-BW-63C Pirelli 63 - 55.9 - 65.3

E1AJ-BW-63 CMP 63 - 55.9 - 68.2

E1AJ-BW-75C Pirelli 75 - 67.9 - 78.0

E1AJ-BW-75 CMP 75 - 67.9 - 82.9




Min Max Min Max


17/44

12

ACCESSORIES

12:17

E1W Brass Gland with Inner andOuter Seals

BS6121: Part 1

Suitable for single wire armoured, plasticor rubber sheathed, extruded bedded cables.


Inner seal grips bedded layer of cable.

Weatherproof and waterproof.

Inner and outer seal rated to IP66

Gland rated to IP66 with use of suitable sealing washer or thread sealant at

gland interface.


Pirelli Up to size 25: - 2 per kit Size 32 and above:- 1 per kit

CMP Up to size 32:- 2 per kit Size 40 and above:- 1 per kitNB Pirelli glands have separate armour locking rings.

CMP glands have integral knurled armour lock.


E1BA-E1W-20S Pirelli 20S 8.7 11.6 8.0 15.8

E1BA-E1W-20SC CMP 20S 6.1 11.6 11.4 15.9

E1BA-E1W-20 Pirelli 20 11.7 13.9 12.9 20.8

E1BA-E1W-20C CMP 20 6.5 13.9 15.0 20.9

E1BA-E1W-25 Pirelli 25 13.0 19.9 17.0 27.2

E1BA-E1W-25C CMP 25 11.1 19.9 20.3 27.4

E1BA-E1W-32 Pirelli 32 20.0 26.2 23.5 33.5

E1BA-E1W-32C CMP 32 17.0 26.2 26.0 33.9

E1BA-E1W-40 Pirelli 40 26.3 32.1 29.0 39.9

E1BA-E1W-40C CMP 40 22.0 32.1 31.0 40.4

E1BA-E1W-50S Pirelli 50S 32.2 38.1 38.0 46.2

E1BA-E1W-50SC CMP 50S 29.5 38.1 36.5 46.7E1BA-E1W-50 Pirelli 50 38.2 44.0 39.5 52.6

E1BA-E1W-50C CMP 50 35.6 44.0 43.0 53.1

E1BA-E1W-63 Pirelli 63 50.1 55.9 51.3 65.3

E1BA-E1W-63C CMP 63 47.2 55.9 58.0 65.9

E1BA-E1W-75S Pirelli 75S 56.0 61.9 62.0 71.6




Min Max Min Max


18/44

ACCESSORIES

2:18

12

Low Smoke and Fume Gland Kits

Convenient ready to use kits.

Contain everything necessary to terminate an LSF cable run - gland(s) withLSF seal(s), backnuts(s), earth tag(s) and LSF shroud(s).

Zero halogen.

Complies with the test criteria of BS6724, BS6853 category 1.

Continuous operating temperature of -500C to 1500C

Resists most chemicals, solvents, acids, alkalis, oils, moisture, steam and UV

light.

Excellent tear resistance.

NOTE: The materials utilised in these kits are noted for the absence of smoke

generating constituents, particularly halogens (flourine, bromine and chlorine)

thus avoiding the hazards of highly irritant and toxic fumes emitted by standard

materials such as PCP and PVC when exposed to flame.


19/44

12

ACCESSORIES

12:19

BW Brass Gland - LSF

To BS6121: Part 1.

Suitable for single wire armoured,

plastic or rubber sheathed cables. For use in dry, indoor situations.

Low cost two-part design.

IP54.

LSF shroud may be used for additional

ingress protection.

Glands are supplied in kit form, complete with locknuts and shrouds.




E1AJ-BW-20SLSF Pirelli 20S - 11.6 - 15.8

E1AJ-BW-20LSF Pirelli 20 - 13.9 - 20.8










Min Max Min Max


20/44

ACCESSORIES

2:20

12

CW Brass Gland with Outer LSF Seal

To BS6121: Part 1.

Suitable for single wire armoured, plastic

or rubber sheathed cables.

Outer LSF seal grips sheath of cable.


Seal rated to IP66

Design has separate armour locking ring.


washer or thread sealant at gland interface.

Glands are supplied in kit form, complete with locknuts and LSF shrouds.




E1AG-CW-20SSLSF Pirelli 20SS - 8.6 8.0 13.2

E1AG-CW-20SLSF Pirelli 20S - 11.6 8.0 15.8

E1AG-CW-20LSF Pirelli 20 - 13.9 12.9 20.8




E1AG-CW-50SLSF Pirelli 50S - 38.1 38.0 46.2







Min Max Min Max


21/44

12

ACCESSORIES

12:21

Selecting Glands for Hazardous AreasZONE CLASSIFICATION

Zone 0 (Division 0)

Explosive gas/air mixture is continuously present or for long periods. No

equipment should be terminated in this zone.

Zone 1 (Division 1)

Explosive gas/air mixture is likely to occur in normal operation.

Zone 2 (Division 2)

Explosive gas/air mixture is not likely to occur and if so, only for a short period of time.

Increased Safety Glands(E.Exe)

For use in hazardous environments and comply with EN50014 and EN 50019

(BS5501 Part 1 and Part 6). These glands can only be used where no parts of

the electrical equipment can produce sparks/arcing or exceeds the gas ignition

temperature. E.Exe glands are normally recommended for Zone 2 applications

but can be used in Zone 1, i.e. indirect entry situations.

Flameproof (E.Exd) Glands

For use in hazardous environments and comply with EN50014 and EN50018

(BS5501 Part 1 and Part 5). These glands are approved for direct entry

applications in Zone 1 areas, IIA, IIB or IIC gas groups with the exception of A2Fglands which are for IIA and IIB groupings - may also be used in Zone 2 areas.

Explosion Proof Barrier Glands

For use in hazardous environments and comply with EN50014 and EN 50018

(BS5501 Part 1 and Part 5). These glands are approved for direct entry

applications in Zone 1 areas, IIA, IIB, or more commonly IIC gas groups.

Selecting Barrier Glands as opposed to Conventional Flameproof Glands

The main applications for the specification of barrier glands in accordance with

the relevant codes of practice, can be summarised as follows:

with enclosures containing an ignition source and installed in Group IIC gas areas

with an enclosure containing an ignition source and in a Zone 1 area where

the volume of the enclosure exceeds 2 litres

with cables other than those specified in BS5308, BS5467, BS6116, BS6346

and 6883

where 'cold flow' of cable installation is considered a possibility

to prevent gas migration from one area to another to prevent moisture migration in cables

where the user assessment considers a barrier gland essential for safety


22/44


23/44

12

ACCESSORIES

12:23


E1BN-E1WF-20SS Pirelli 20SS 3.81 8.74 8.0 13.2

E1BN-E1WF-20S Pirelli 20S 8.0 11.79 8.0 15.8

E1BN-E1WF-20 Pirelli 20 11.79 14.15 12.9 20.8

E1BN-E1WF-25 Pirelli 25 14.0 20.12 17.0 27.2

E1BN-E1WF-32 Pirelli 32 19.7 26.55 23.5 33.5

E1BN-E1WF-40 Pirelli 40 26.55 32.42 29.0 39.9

E1BN-E1WF-50 Pirelli 50 38.39 44.33 39.5 52.6

E1BN-E1WF-63 Pirelli 63 50.27 56.24 51.3 65.3




Min Max Min Max

E1WF Flameproof Gland with Inner & Outer Seals

Suitable for single wire armoured, plastic or rubber sheathed, extruded bedded cables.





Design has separate outer locking ring. Gland rated to IP66 with use of suitable sealing washer or thread sealant at gland interface.

For use with flameproof equipment or increased safety equipment.

Complies with group II C hazardous atmospheres EN50014 and EN50018 (BS5501

Part 1 and Part 5).

BASEEFA Approved.

Zone 1 and Zone 2 applications.

Pirelli glands are supplied in kit form completPirellie with locknuts, earthtags and shrouds.Up to size 25: - 2 per kit Size 32 and above:- 1 per kit


24/44

ACCESSORIES

2:24

12


E1BP-E1XF-16 Pirelli 16 3.81 8.74 8.0 13.2

E1BP-E1XF-20SS Pirelli 20SS 3.81 8.74 8.0 13.2

E1BP-E1XF-20S Pirelli 20S 8.0 11.79 8.0 15.8

E1BP-E1XF-20 Pirelli 20 11.79 14.15 12.9 20.8

E1BP-E1XF-25 Pirelli 25 14.0 20.12 17.0 27.2

E1BP-E1XF-32 Pirelli 32 19.7 26.55 23.5 33.5

E1BP-E1XF-40 Pirelli 40 26.55 32.42 29.0 39.9


E1BP-E1XF-50 Pirelli 50 38.39 44.33 39.5 52.6





Min Max Min Max

E1XF Flameproof Gland with Inner & Outer Seals

Suitable for wire braid armoured, plastic or rubber sheathed, extruded bedded cables.





Design has separate outer locking ring.

Gland rated to IP66 with use of suitable sealing washer or thread sealant at gland interface.

For use with flameproof equipment or increased safety equipment (E.Exd or E.Exe).

Complies with group II C hazardous atmospheres EN50014 and EN50018 (BS5501

Part 1 and Part 5).

BASEEFA Approved.


Pirelli glands are supplied in kit form complete with locknuts, earthtags and shrouds.

Up to size 25: - 2 per kit Size 32 and above:- 1 per kit


25/44

12

ACCESSORIES

12:25


E1BP-EXC-20S-A Pirelli 20S 7.0 12.0 9.0 16.0

E1BP-EXC-20-A Pirelli 20 8.0 14.4 11.5 21.0

E1BP-EXC-25-A Pirelli 25 10.5 20.2 18.5 27.5

E1BP-EXC-32-A Pirelli 32 15.5 26.5 21.0 34.0

E1BP-EXC-40-A Pirelli 40 23.0 32.5 31.0 41.5

E1BP-EXC-50-A Pirelli 50 28.5 44.5 36.0 52.5

E1BP-EXC-63-A Pirelli 63 44.0 56.5 50.0 65.5

E1BP-EXC-75-A Pirelli 75 53.0 68.5 59.0 78.0




Min Max Min Max

Excelplus Deluge Proof Flameproof & IncreasedSafety Gland with Inner & Outer Seals

Suitable for wire braid and single wire armoured,

plastic or rubber sheathed, extruded bedded cables. Outer seal grips sheath of cable.


Weatherproof, waterproof and deluge proof.

Inner and outer seal rated to IP67.

Design has separate armour locking ring and

additional locking ring to ensure integrity of

armour lock under vibrating conditions.

Gland rated to IP67 with use of suitable sealing washer or thread sealant at gland interface. For use with flameproof equipment or increased safety equipment (E.Exd or E.Exe).

Dual certified.

Complies with group II C hazardous atmospheres EN50014, EN50018 and

EN50019 (BS5501 Part 1, Part 5 and Part 6).

BASEEFA Approved.


Supplied as gland only.


26/44

ACCESSORIES

2:26

12


E1DZ-UNI-20S HAWKE 20S 7.5 11.9 9.5 16.0

E1DZ-UNI-20 HAWKE 20 9.4 14.3 12.5 20.5

E1DZ-UNI-25 HAWKE 25 12.1 20.2 16.9 26.0

E1DZ-UNI-32 HAWKE 32 17.6 26.5 22.0 33.0

E1DZ-UNI-40 HAWKE 40 23.1 32.5 28.0 41.0

E1DZ-UNI-50 HAWKE 50 28.9 44.4 36.0 52.6

E1DZ-UNI-63 HAWKE 63 39.9 56.3 46.0 65.3

E1DZ-UNI-75 HAWKE 75 50.5 68.2 57.0 78.0




Min Max Min Max

Universal Flameproof & Increased SafetyGland with Inner & Outer Seals

Suitable for wire braid, single wire, steel tape and strip armoured plastic orrubber sheathed, extruded bedded cables.






Gland rated to IP66 with use of suitable sealing washer or thread sealant at

gland interface.

For use with flameproof equipment or increased safety equipment (E.Exd or

E.Exe).

Complies with group II C hazardous atmospheres EN50014, EN50018 and

EN50019 (BS5501 Part 1, Part 5 and Part 6).

BASEEFA Approved.


Incorporates external boot seal which offers protection against moisture

ingress to the armour.

Glands are supplied in kit form complete with locknut, earthtag, shroud, nylon

washer and serrated washers.

All sizes: 1 per kit


27/44

12

ACCESSORIES

12:27

E2WF (RTLF) Flameproof Gland withInner & Outer Seals

Suitable for SWA, plastic or rubber oversheathed, lead inner sheath cables.


Inner seal grips and provides earth continuity to lead sheath.




RTLF for use with flameproof equipment or increased safety equipment.

Complies with group II C hazardous atmospheres EN50014 and EN50018

(BS5501 Part 1 and Part 5).

BASEEFA Approved. Zone 1 and Zone 2 applications.


E1CF-RTLF-20SH-A HAWKE 20S 7.0 9.6 10.5 16.0

E1CF-RTLF-20H-A HAWKE 20 8.0 12.0 12.9 20.9

E1CF-RTLF-25H-A HAWKE 25 11.5 17.0 17.0 27.1


E1CF-RTLF-32H-A HAWKE 32 18.0 23.0 25.0 33.3


E1CF-RTLF-40H-A HAWKE 40 23.0 29.0 33.0 42.9


E1CF-RTLF-50H-A HAWKE 50 34.0 40.0 39.5 52.6

Glands are supplied as gland only.



Over lead sheath Overall

Min Max Min Max


28/44

ACCESSORIES

2:28

12

UniversalExplosion Proof Barrier Glands

For plastic or rubber insulated cables with wire braid, single wire, steel tape

or strip armour, having extruded or taped bedding.

Solid setting compound is squeezed into the interstices of the cable whengland is installed.

Compound forms a barrier around individual cores so preventing escape of

gases through centre of cable.

Sealing arrangements are rated to IP66.


For use with explosion proof equipment in Zone 1 hazardous areas.

Complies with group II C qualifies the gland for use under the most onerous

conditions.

BASEEFA Approved.

Approved to EN50014 and EN50018 (BS5501 Part 1 and Part 5)


E1BS-UNI-20S-A HAWKE 20S - 10.0 9.5 16.0

E1BS-UNI-20-A HAWKE 20 - 12.5 12.5 20.5

E1BS-UNI-25-A HAWKE 25 - 18.4 16.9 26.0

E1BS-UNI-32-A HAWKE 32 - 24.7 22.0 33.0

E1BS-UNI-40H-A HAWKE 40 - 29.7 28.0 41.0

E1BS-UNI-50H-A HAWKE 50 - 41.7 36.0 52.6

Glands are supplied body only with 2 compound mixes.



Under armour OverallMin Max Min Max


29/44

12

ACCESSORIES

12:29

Brass Earth Tags

Ensure earth continuity is maintained between the gland and the equipment.

Aluminium earth tags should be used with aluminium glands.

NOTE:

Earth bond connections are specified in IEE wiring regulations and relevant

Codes of Practice.

TAG DETAILS

Anixter ISO Entry Bolt HolePart No. Thread Diameter Diameter

(mm) (mm)

E1BG-20R 20 7.2

E1BG-25R 25 10.3E1BG-32R 32 11.9

E1BG-40R 40 13.5

E1BG-50R 50 13.5

E1BG-63R 63 13.5

E1BG-75R 75 13.5


30/44

ACCESSORIES

2:30

12

High Performance Sealing Washers

Improve the IP rating between the gland

and the equipment i.e. IP66.

Fibre or Nylon available according tocustomer preference.

SEALINGWASHER

EQUIPMENTINTERFACE

WASHER DETAILS

Anixter ISO Entry Washer

Part No. Thread Diameter Material

(mm)

E1DS-20R 20 NYLON

E1DS-25R 25 NYLONE1DS-32R 32 NYLON

E1DS-40R 40 NYLON

E1DS-50R 50 NYLON

E1DS-63R 63 NYLON

E1DS-75R 75 NYLON

E1DT-20 20 FIBRE

E1DT-25 25 FIBRE

E1DT-32 32 FIBRE

E1DT-40 40 FIIBRE

E1DT-50 50 FIBRE

E1DT-63 63 FIBRE

E1DT-75 75 FIBRE

Galvanised Serrated Washers

Used to prevent loosening oflocknut

Mild steel zinc plated

WASHER DETAILS

Anixter ISO EntryPart No. Thread Diameter

(mm)

E1DY-20 20

E1DY-25 25

E1DY-32 32

E1DY-40 40

E1DY-50 50


31/44

12

ACCESSORIES

12:31

Steel, Brass & Aluminium Locknuts

Used to secure gland body to the equipment where entry hole is not tapped.

Brass backnuts recommended for most corrosive environments.

Aluminium backnuts should be used with aluminium glands.

Steel backnuts are primarily for dry, low humidity environments.

Steel and aluminium locknuts are available when required.

LOCKNUT DETAILS

Anixter ISO Entry Locknut

Part No. Thread Diameter Material

(mm)

E1BK-20R 20 BRASS

E1BK-25R 25 BRASS

E1BK-32R 32 BRASS

E1BK-40R 40 BRASS

E1BK-50R 50 BRASS

E1BK-63R 63 BRASS

E1BK-75R 75 BRASS


32/44

ACCESSORIES

2:32

12

PC P/PVC Shrouds

For fitting over cable glands where additional protection against onerous

weather conditions and corrosion is required.

Provide an effective seal onto both gland and cable oversheath.

PCP shrouds are particularly recommended for outdoor and the most hostile

conditions and are not affected by ultravoilet rays contained in sunlight.

PVC shrouds for use in dry indoor and most outdoor situations.

SHROUD DETAILS

Anixter To Suit Shroud

Part No. Gland Size Material

(mm)

E1BF-20SH 20S PCP

E1BF-20H 20 PCP

E1BF-25H 25 PCP

E1BF-32H 32 PCP

E1BF-40H 40 PCP

E1BF-50H 50 PCPE1BF-63H 63 PCP

E1BF-75H 75 PCP

E1DR-20SH 20S PVC

E1DR-20H 20 PVC

E1DR-25H 25 PVC

E1DR-32H 32 PVC

E1DR-40H 40 PVC

E1DR-50H 50 PVC

E1DR-63H 63 PVCE1DR-75H 75 PVC


33/44

12

ACCESSORIES

12:33

Lugs for Medium Voltage Cables

These compression lugs are based on the standard tin plated connectors

manufactured by Pirelli, and are suitable for indoor and outdoor applications.Connections are manufactured from thickwall copper tubing and incorporate

single hole palm. The base of the compression barrel is effectively waterblocked

via incorporation of a waterproof seal during manufacture.

LUG DETAILS

Anixter To Suit Stud

Part No. Conductor Size Size(mm2) (mm)

E1AE-BTHW-70-C12 70 12

E1AE-BTHW-95-C16 95 16

E1AE-BTHW-120-C16 120 16

E1AE-BTHW-150-C16 150 16

E1AE-BTHW-185-C16 185 16

E1AE-BTHW-240-C20 240 20


34/44

ACCESSORIES

2:34

12

Lugs

The use of compression lugs for securing conductors to terminals has long been

recognised as offering the optimum combination of electrical integrity, reliability and

speedy installation. Single hole, two hole and four hole palm lugs available.

The compression system ensures a high level of termination when used in association

with tooling supplied by the same manufacturer ensuring that the completed installation

complies with the standards laid down in BS4579 Part 1 (Compression joints in copper

conductors). Anixter stocks uninsulated compression lugs, manufactured by Pirelli

Components, produced from high conductivity electrolytic copper having a tin plated

finish for operating temperatures up to 1500C and also to prevent corrosion.


35/44

12

ACCESSORIES

12:35


Part No. Conductor Size Size

(mm2) (mm)

Flex Str.

E1AE-BT-150-C12 120 150 12E1AE-BT-150-C16 16

E1AE-BT-185-C10 10

E1AE-BT-185-C12 150 185 12

E1AE-BT-185-C16 16

E1AE-BT-185-C20 20

E1AE-BT-240-C12 12

E1AE-BT-240-C16 185 240 16

E1AE-BT-240-C20 20

E1AE-BT-300-C12 240 300 12

E1AE-BT-300-C16 16E1AE-BT-300-C20 20

E1AE-BT-400-C16 300 400 16

E1AE-BT-500-C20 400 500 20

E1AE-BT-630-C20 500 630 20

Two Hole Palm

E1AE-BT-150-C12B2 120 150 12

E1AE-BT-185-C12B2 150 185 12

E1AE-BT-240-C12B2 185 240 12

E1AE-BT-300-C12B2 240 300 12

E1AE-BT-400-C12B2 300 400 12

E1AE-BT-500-C12B2 400 500 12

Four Hole Palm

E1AE-BT-300-C8B4 240 300 8

E1AE-BT-400-C8B4 300 400 8

E1AE-BT-500-C8B4 400 500 8

E1AE-BT-630-C8B4 500 630 8


Part No. Conductor Size Size

(mm2) (mm)

Flex Str.

Single Hole Palm

E1AE-BT-6-C5 4.0 5E1AE-BT-6-C6 to 6

E1AE-BT-6-C8 6.0 8

E1AE-BT-6-C10 10

E1AE-BT-10-C5 10 5

E1AE-BT-10-C6 6

E1AE-BT-10-C8 8

E1AE-BT-10-C10 10

E1AE-BT-10-C12 12

E1AE-BT-16-C5 10 16 5

E1AE-BT-16-C6 6E1AE-BT-16-C8 8

E1AE-BT-16-C10 10

E1AE-BT-16-C12 12

E1AE-BT-25-C6 16 25 6

E1AE-BT-25-C8 8

E1AE-BT-25-C10 10

E1AE-BT-25-C12 12

E1AE-BT-35-C6 25 35 6

E1AE-BT-35-C8 8

E1AE-BT-35-C10 10

E1AE-BT-35-C12 12

E1AE-BT-50-C6 35 50 6

E1AE-BT-50-C8 8

E1AE-BT-50-C10 10

E1AE-BT-50-C12 12

E1AE-BT-70-C8 50 70 8

E1AE-BT-70-C10 10

E1AE-BT-70-C12 12

E1AE-BT-70-C16 16E1AE-BT-95-C10 70 95 10

E1AE-BT-95-C12 12

E1AE-BT-95-C16 16

E1AE-BT-120-C10 10

E1AE-BT-120-C12 95 120 12

E1AE-BT-120-C16 16

E1AE-BT-120-C20 20

E1AE-BT-150-C10 10


36/44

ACCESSORIES

2:36

12

Telcleats - Black Polythene & Grey LSF

Range taking and self adjusting

Just 8 sizes cover from 10mm to

51mm diameter Ultraviolet and weather resistant

Low cost

Versatile

One piece

Single fixing

LSF cleats are low smoke and fume

emission and zero halogen

Coloured grey to distinguish from black coloured Telcleat

Meets requirements of BS6853 and LUL specification E1042 with regards to

temperature index, smoke emission and toxicity ratings.

CLEAT DETAILS

Anixter Cable Dimensions

Part No. Accomodated

Min (mm) Max (mm)

Black PolytheneE1D-A01 10 15

E1D-A02 12 17

E1D-A03 15 20

E1D-A04 18 24

E1D-A05 22 29

E1D-A06 26 34

E1D-A07 32 42

E1D-A08 39 51

Grey LSF

E1D-A01LSF 10 15

E1D-A02LSF 12 17

E1D-A03LSF 15 20

E1D-A04LSF 18 24

E1D-A05LSF 22 29

E1D-A06LSF 26 34

E1D-A07LSF 32 42

E1D-A08LSF 39 51


37/44

Anixter To Suit Conductor Size Shell Internal To Suit

Cable

DiameterPart No. Length Diameter

(mm) (mm) (mm)

SJK1

Two Core

(mm2)

1.5 to 4.0

6.0 to 25.0

35, 50

70, 95

120, 150, 185

240, 300

400

Three Core

(mm2)

1.5 to 4.0

6.0, 10.0

16, 25

35, 50

70, 95, 120

150, 185, 240

300, 400

Four Core

(mm2)

1.5, 2.5

4.0 to 10.0

16

25, 35, 50

70, 95, 120

150, 185

240, 300, 400

190

260

360

400

530

705

900

36

47

55

70

100

125

150

14.0 - 22.0

14.0 - 30.0

20.0 - 37.0

25.0 - 42.0

33.0 - 55.0

45.0 - 74.0

50.0 - 90.0

SJK2

SJK3

SJK4

SJK5

SJK6

SJK7

SJK3 and SJK4 kits.

12

ACCESSORIES

12:37

Straight Cable JointsPolyurethane Resin Encapsulation Suitable for 2, 3, 4 core

XLPE/PVC SWA Copper Conductor Cables

Joints comply with BS6910 Part 1.

Transparent shell to allow inspection of

joint before application of resin. Joints

utilise Two-Part Polyurethane resin to

encapsulate, insulate and protect the

jointed conductors.

Resin and hardener are separated by a

centre peelable seal in Twin Pack Laminated Sachet (completely enclosed mixing).

Unmixed ingredients have shelf life of 24 months based on average UK temperature.

Compression connectors for relevant conductor size are SJK1, SJK2,

Armour bonds included in all kits.

Simple to use - no special tools required.

Supplied in resealable box.


38/44

ACCESSORIES

2:38

12

Claw & Two Bolt Cleats -Aluminium Alloy

Claw cleats for cable dimensions up to 51mm diameter.

Two bolt cleats for cable dimensions 51mm and above.

CLEAT DETAILS

Anixter Cable Dimensions

Part No. Accomodated

Min (mm) Max (mm)

Claw Cleats

E1B-BA01 10 13

E1B-BA02 13 16

E1B-BA03 16 19

E1B-BA04 19 22

E1B-BA05 22 25

E1B-BA06 25 32

E1B-BA07 32 38

E1B-BA08 38 44

E1B-BA09 44 51

Two Bolt Cleats

E1B-BA10 51 57

E1B-BA11 57 64

E1B-BA12 64 70

E1B-BA13 70 76

E1B-BA14 76 83

E1B-BA15 83 89


39/44

12

ACCESSORIES

12:39

Cable Tiles & Warning Tapes

Plastic warning cable tiles and warning tapes for buried cables and have the

following warning legend:

CAUTION CAUTION

ELECTRIC CABLE BELOW

CABLE TILE DETAILS

Anixter Tile

Part No. Dimensions (mm)

500315 1000 x 152 x 12

500314 1000 x 244 x 12

500313 1000 x 300 x 12

WARNING TAPE DETAILS

Anixter Tile

Part No. Dimensions (mm)

515319 150mm wide x 100 microns thick

(365m roll)


40/44

ACCESSORIES

2:40

12

11kV Indoor Termination Kitsfor 3 Core PILC/PICAS Cables

Scotchcast termination kits for use on

11kV indoor terminations for 3 core paperinsulated, belted, lead sheath and

corrugated aluminium sheath cables.

Inorganic cold shrink silicone insulator.

Cold pour Scotchcastresin to insulate

and fill crotch area.

Light weight assembly

No special tools necessary

Cold shrink technology, no heating required

11kV rated voltage

95kV nominal impluse withstand voltage

700C maximum operating temperature (accelerated ageing test to VDE0278)

1600C overload temperature (accelerated ageing test to VDE0278)

Track resistance on silicone insulator as per ASTM [email protected] - 30 hours @3.5kV - 10 hours

Contents list of kit:

- EPDM rubber pre-stretched tubes

- Silicone Glove

- Silicone pre-stretched tubes

- Polyetherurethane resin

- Self amalgamating tapes:

- Stress control tape- EPR rubber tape

- Silicone tape

- Core separator

- Cable cleaner

- Gloves

- Drawing instructions

Scotchcast is a registered Trade Mark of 3M.

Anixter 3M Suitable Approx.

Part No. Part No. for Conductor Kit

Sizes Weight

(mm2) (kg)

E1DW-MT16 MT16 70-400 3.5


41/44

12

ACCESSORIES

12:41

11kV Indoor Termination Kitsfor 3 Core Polymeric Cables

Scotchcast termination kits for use on

11kV indoor terminations for 3 cores XLPEor EPR insulated cables.

Inorganic cold shrink silicone insulator.

Light weight assembly



11kV rated voltage

95kV nominal impluse withstand voltage

950C maximum operating temperature (accelerated ageing test to VDE0278)

2500C overload temperature (accelerated ageing test to VDE0278)

Track resistance on EPDM insulator as per ASTM 2303-68

@2.5kV - 5 hours

Contents list of kit:

- EPDM rubber pre-stretched tubes

- EPDM Rubber Glove

- Self amalgamating tapes:

- Semi-conducting tape

- EPR rubber tape

- Copper earth braid with integral lug

- Constant force springs

- Cable cleaner

- Drawing instructions

Scotchcast is a registered Trade Mark of 3M.



Sizes Weight

(mm2) (kg)

E1DW-MT46 MT46 35-70 3.0

E1DW-MT47 MT47 95-185 2.5

E1DW-MT48 MT48 240-400 3.0


42/44

ACCESSORIES

2:42

12

3M Inline (Straight) Barrier Boot - MB63

Installation of cable termination to bushing connections in switchgear and

cable end boxes for straight (in-line) applications.

Suitable for paper or polymeric cables


Quick and simple installation


11kV rated voltage (75kV BIL)

Track resistant EPDM material

For use on conductor sizes up to 630mm2

Dimensions of cable box and bushing dimensions should meet the

following criteria:

Dimension Description Min Max

(mm) (mm)

A Phase - Earth clearance 18 76*

B Phase - Phase clearance 36 127*

C Bushing diameter 50mm up bushing 24 66

D Bushing length 50 127*

* For dimensions greater than these no boots are required.

NB: 3 barrier boots are provided in each kit.



Sizes Weight

(mm2) (kg)

E1DW-MB63 MB63 Up to 630 0.8

"A""B"

"C"

"D"


43/44

12

ACCESSORIES

12:43

3M Pre-Moulded Right Angle Barrier Boot

Installation of cable termination to bushing connections in

switchgear and cable end boxes for right angle

applications. Consists of one large tubular opening to

fit a porcelain bushing, and a smaller stepped tubular

opening to cover the cable lugs and fit over the cable

terminations. A sealing cover is also included which

allows the connection bolts to be accessed after barrier

boot has been slipped onto the bushing and

termination. The sealing cover guarantees an

electrical sealing of the live parts and is re-enterable.

Suitable for paper or polymeric cables


Quick and simple installation

Re-enterable design

No heating required

11kV rated voltage (95kV BIL)

Track resistant EPDM material

For use in conductor sizes 35 - 300mm2

Dimensions of cable box and bushing dimensions should meet the following criteria:

Dimension Description Min Max

(mm) (mm)

A Phase - Earth clearance 30 76*

B Phase - Phase clearance 70 127*

C Bushing length 110 127*

D Bushing diameter at length C(circular bushing) 45** 50

E Bushing circumference at length C 140** 157

(eliptical bushing)

* For dimensions greater than these no boots are required.

** Bushings below these minumum dimensions can be catered for using 3Ms MB64/S

supplementary kit(s) in conjunction with the standard MB 64 kit.

NB: 3 barrier boots are provided in each kit.

"B" "A"



Sizes Weight

(mm2) (kg)

E1DW-MB64 MB64 35 - 300 1.05

"C"X

X

"D"

Section XX

Circular Bushing

Elliptical Bushing

"E"


44/44

Documents

Glands_Accessories LSF.pdf