Upload
jyotika-aggarwal
View
223
Download
0
Embed Size (px)
Citation preview
8/8/2019 Gears Types
1/20
Gears Types
Gears are categorized into several types. They are used in a wide era of industriesincluding automotive, milling, paper industry etc. According to different applications in
industries and different materials used they are categorized separately. Different types of
gears are also custom design and are fabricated by gear manufacturing services as par
the specifications
1- Angular Bevel Gears
These are bevel gears whose shafts are set at an angle other than 90 degrees. They are
useful when the direction of a shaft's rotation needs to be changed. Using gears of
differing numbers of teeth can change the speed of rotation.
These gears permit minor adjustment of gears during assembly and allow for some
displacement due to deflection under operating loads without concentrating the load on
8/8/2019 Gears Types
2/20
the end of the tooth. For reliable performance, Gears must be pinned to shaft with a
dowel or taper pin.
The bevel gears find its application in locomotives, marine applications, automobiles,printing presses, cooling towers, power plants, steel plants, defence and also in railway
track inspection machine. They are important components on all current rotorcraft drive
system.
2- Bevel Gears
They connect intersecting axes and come in several types. The pitch surface of bevel
gears is a cone. They are useful when the direction of a shaft's rotation needs to be
changed. Using gears of differing numbers of teeth can change the speed of rotation.
They are usually mounted on shafts that are 90 degrees apart, but can be designed to
work at other angles as well.
8/8/2019 Gears Types
3/20
These gears permit minor adjustment during assembly and allow for some displacement
due to deflection under operating loads without concentrating the load on the end of the
tooth. For reliable performance, Gears must be pinned to shaft with a dowel or taper pin.
Bevel gear sets consist of two gears of different pitch diameter that yield ratios greater
than 1:1.
Types
The teeth on bevel gears can be straight, spiral or bevel. In straight bevel gears teeth
have no helix angles. They either have equal size gears with 90 degrees shaft angle or a
shaft angle other than 90 degrees. Straight bevel angle can also be with one gear flat with
a pitch angle of 90 degrees. In straight when each tooth engages it impacts the
corresponding tooth and simply curving the gear teeth can solve the problem. Spiral
bevel gears have spiral angles, which gives performance improvements. The contact
between the teeth starts at one end of the gear and then spreads across the whole tooth.
In both the bevel types of gears the shaft must be perpendicular to each other and must
be in the same plane. The hypoid bevel gears can engage with the axes in different
planes. This is used in many car differentials. The ring gear of the differential and the
input pinion gear are both hypoid. This allows input pinion to be mounted lower than the
axis of the ring gear. Hypoid gears are stronger, operate more quietly and can be usedfor higher reduction ratios. They also have sliding action along the teeth, potentially
reducing efficiency.
Applications
A good example of bevel gears is seen as the main mechanism for a hand drill. As the
handle of the drill is turned in a vertical direction, the bevel gears change the rotation of
the chuck to a horizontal rotation. The bevel gears in a hand drill have the added
advantage of increasing the speed of rotation of the chuck and this makes it possible to
drill a range of materials.
8/8/2019 Gears Types
4/20
The bevel gears find its application in locomotives, marine applications, automobiles,
printing presses, cooling towers, power plants, steel plants, defence and also in railway
track inspection machine. They are important components on all current rotorcraft drive
system.
Spiral bevel gears are important components on all current rotorcraft drive systems.
These components are required to operate at high speeds, high loads, and for an
extremely large number of load cycles. In this application, spiral bevel gears are used to
redirect the shaft from the horizontal gas turbine engine to the vertical rotor.
3- Crown Wheel
A crown wheel is a wheel with cogs or teeth set at right angles to its plane. The internal
diameter of a crown wheel is ground by holding the component in pitch like chucks to
ensure accuracy of the finished gear
8/8/2019 Gears Types
5/20
As a result of the development of "flat" crown wheels it has become possible to
construct a special gearbox. IHC has used these new gearwheels to produce a prototype
of a continuously variable speed gearbox.
Applications
Crown wheels are used in motorcycle automotive gearboxes. It is also used in
mechanical clocks. The clock consists of a crown wheel, rotated by a falling weight,
whose teeth drive the pallets of a verge backward and forward. This verge is connected
to an arm with a hammer on the end that struck the bell.
4- Crown Wheel and Pinion
8/8/2019 Gears Types
6/20
A crown wheel is a wheel with cogs or teeth set at right angles to its plane and the pinion
is a small cogwheel that meshes with the crown wheel. Crown wheel and pinion have
excellent heat distortion control, high strength, wear resistance property and noiselessand vibration free operation. They are made of fine-grained steel billet.
The pinion thread is specially made on the thread grinder to ensure proper fitting. Tooth
contact of a crown pinion is inspected on a Gleason machine at regular intervals of time
for uniform hardness and adequate case depth. They are checked thoroughly for high
spots because this ensures premature failure and noise-free operation. The crown wheel
& pinion are paired and checked for centralized tooth bearing and desired proximity. An
elliptoid contact pattern is ensured between the crown wheel and pinion.
In a machine, when any torque is applied to the drive unit, the tendency is for the crown
wheel and pinion to be forced into or out of mesh by the sliding contact. The amount of
pre-load on the bearings determines how much torque can be transmitted without
allowing end float, which cause the meshing of the gears to become incorrect.
Application
Crown wheel & pinion are used widely in automotive industries. They are one of the most
stress prone parts of a vehicle. They are used in automobiles to maintain forward motion.
To maintain forward motion both output drive shaft sides covers are removed and the
pinion and crown wheel are swapped completely with differential.
8/8/2019 Gears Types
7/20
5-Differential Gears
Differential gears link two shafts with a covering, forcing the total of the rotational angles
of the shafts to be the same as the rotational angles of the covering. Arrangement of the
system is done in such a way that one axle turns faster than the other.
When a differential gear is meshed with the other gear then the highly efficient torque isapplied from the differential side gears to the axle shaft. When torque level decreases
then the gear separating forces also decreases allowing the axle shaft to rotate
independently. Differential gears can add or subtract the movement of two inputs. In
practical terms, they will turn the number of revolutions proportional to the movements
of both inputs. They are used to convert the lengthwise flow of power from the engine
through the clutches, transmissions, and propeller shafts into a right-angle direction.
This change allows the engine power to turn the wheels.
In the differential gears there are two coaxial gears, the pinions and the turntable.
Pinions are mounted on intermediate shafts and these shafts are connected to a fixed
carrier called the turntable. The differential gears are lubricated with a fluid that absorbs
heat and increases the life and performance of the gears as well as the wheel. Regular
driving subjects the fluid to high heat that breaks the fluid at a later stage. This results in
the contact of two metals, which eventually increases the heat and prevents the gear
from turning the car's wheel. So, the fluid should be properly checked in regular
8/8/2019 Gears Types
8/20
intervals.
Types of Differential Gears
There are two designs of differential gears, hypoid and spiral.
Spiral Differential - In spiral differential the pinion gears contacts the ring gears at its
centerline .
Hypoid Gear - In the hypoid the pinion gear contacts the ring gear below the centerline.
The size of pinion gear in hypoid differential is much smaller and the contact ratio is
high, comparatively hypoid differential is much stronger than the spiral differential.
Applications
Differential gears in automobiles are the most common application of these gears. When
the car is moving in a straight line, there is no movement of the differential gear withrespect to its axis but when the car takes a turn then these gears help two wheels of the
car to rotate differentially with respect to each other. When one wheel is stationary then
the counterpart wheel rotates at twice of its expected speed.
6- Fine Pitch Gears
8/8/2019 Gears Types
9/20
They are widely used in aerospace, nuclear and medical industries. They are available in
plastic, steel, stainless steel and brass. They are used largely to transmit motion rather
than power. They have high tooth strength.
Fine pitch gears are inspected by functional testing on a variable-center-distance fixture.
They do not lend themselves to the kind of detailed tooth measurements because of their
small dimensions.
Fine pitch gear is used widely in oil industry and for automotive transmission.
7- Girth Gears
8/8/2019 Gears Types
10/20
The girth gear has been preferred over the gearless drives due to their lower initial cost,
simplicity to install, operate and maintain. In the past many years girth gears have gone
through enormous improvements.
They have high efficiency and the overall life of these gears depends upon proper
lubrication and alignment. They are high quality, high precision component. The capital
cost of girth gears is lower than others and they take less time to install. They are
physically big and due to this they are unable to store for longer periods of time.
Girth gear materials have made several changes on their own. Casting is enhanced using
full ring risering techniques. Simulation programs are installed for verification of proper
solidification. New materials are used with an added advantage of increase in hardness
and therefore increased ratings.
The girth gear is the heart of most mills and kiln drive system. They can't be used in
spare parts inventory. They are also used in steel industry, sugar industry, paper and
pulp industry.
8/8/2019 Gears Types
11/20
8- Hardened and Ground Gears
Hardened and ground gear has two types of shaft arrangements. They can be parallel
shaft type or hollow shaft type. Hardened and ground gear delivers a maximum hob
rotation and table rotation with excellent machining accuracy. Hardened ground gear
provide a noise free and long term operation. They are characterized by high output,
easy operation and precise machining. They offer rigidity, strength and high resistanceto shock load. They are available in a wide range of sizes and gear ratios.
Hardened gears are used in several essential machine tools like wheels, bedways, etc.
and are widely used in the aerospace industry.
9- Helical Bevel Gears
8/8/2019 Gears Types
12/20
Helical bevel gear is a toothed gear in angular design. The input side is provided with a
motor flange or a free input shaft and the output side are provided with a free shaft end
or a hollow shaft. Helical bevel gears are fitted with flanges of various sizes.
Reciprocating tools cuts them.
The advantages of helical bevel gears are high efficiency and low reduction rate. The use
of helical bevel gear saves energy and cost. Helical bevel gears are manufactured by an
alloyed case hardening steel. The gear material is given an extremely strong,homogeneous structure.
They can replace worm gears in a variety of applications, particularly in modular
machinery. They are also used as storage and retrieval unit. They are commonly used in
modern differentials.
10- Helical Gears
8/8/2019 Gears Types
13/20
Helical gears connect parallel shifts but the involute teeth are cut at an angle to the axis
of rotation. Two mating helical gears must have equal helix angle but opposite hand.
They run smoother and more quietly. They have higher load capacity, are more
expensive to manufacture and create axial thrust.
Helical gears can be used to mesh two shafts that are not parallel and can also be used
in a crossed gear mesh connecting two perpendicular shafts. They have longer andstrong teeth. They can carry heavy load because of the greater surface contact with the
teeth. The efficiency is also reduced because of longer surface contact. The gearing is
quieter with less vibration.
Gear Configuration
They can be manufactured in both right-handed and left-handed configurations with a
helix angle to transmit motion and power between non-intersecting shafts that are
parallel or at 90 degrees to each other. For shaft at 90 degrees, the same helix angles are
used and the tooth contact area of the gear is very small. If the angle of gear teeth is
correct, they can be mounted on perpendicular shaft by adjusting the rotating angle by
8/8/2019 Gears Types
14/20
90 degrees. The inclination of the teeth generates an axial force. As the angle of
inclination increases the axial force also increases. Thrust bearings can counter these
forces.
Applications
These are highly used in transmission because they are quieter even at higher speed and
are durable. The other possible applications of helical gears are in ****ile industry,
blowers, feeders, rubber and plastic industry, sand mullers, screen, sugar industry,
rolling mills, food industry, elevators, conveyors, cutters, clay working machinery,
compressors, cane knives and in oil industry.
Disadvantage
A disadvantage of helical gear is the resultant thrust along the axis of the gear, whichneeds to be accomodated by appropriate thrust bearings. This can be overcome by the
use of double helical gears by having teeth with a 'v' shape.
11- Herringbone Gears
8/8/2019 Gears Types
15/20
They conduct power and motion between non-intersecting, parallel axis that may or may
not have center groove with each group making two opposite helices. The two helix
angle come together in the center of the gear face to form a 'V'. in these gears the end
thrust forces cancel themselves out. Its difficult to cut this type of gear but its made
easier by machining a groove in the face at the point of the apex of the 'V' creating a
break in the middle of the herringbone gear teeth. They do not have any separating
groove between the mirrored halves.
Action is equal in force and friction on both gears and all bearings. Herringbone gear
also allow for the use of larger diameter shaft for the same volumetric displacement and
higher differential pressure capability.
The most common application is in power transmission. They utilize curved teeth for
efficient, high capacity power transmission. This offers reduced pulsation due to which
they are highly used for extrusion and polymerization. Herringbone gears are mostly
used on heavy machinery.
8/8/2019 Gears Types
16/20
12- Master Gear
They offer high precision, low volume productions. They are used for composite testing
of production components. They have high speed, quiet operation, longer life and greater
efficiency.
The most common applications are as setting masters and rolling masters for inspection
and production applications. They are used to determine the accuracy of work gears.
When master gears and work gears are rolled together on rolling fixtures dimensional
variations are determined by various indicators, charts or other indicating devices.
Master Gears are also used in aerospace and automotive industry.
13- Mill Headers
8/8/2019 Gears Types
17/20
Mill headers find heavy usage in industrial sectors as an essential part of various
vehicles and machines. They are used in various industrial sectors including coal and
mining, oil exploration, paper mining, chemical industries, cement plant industry, sugar
mill and many more. In industrial sectors these gears are used as an important part of
conveyors, cranes, elevators, separators and kilns because they offer high power-
density and modularity.
14- Miter Gears
8/8/2019 Gears Types
18/20
Miter gears are bevel gears put together with equal numbers of teeth and axes that are
usually at right angles. Miter is the surface forming the beveled end or edge of a piece
where a miter joint is made.
Miter gears are cut with a generated tooth form that has a localized lengthwise tooth
bearing. They are offered in various modules, number of teeth, speed ratio, materials and
designs. Miter gears are made of steel, brass, bronze, aluminum, nylon and duracon.
Features
They are known for efficient power transfer and durability. They can carry heavy loads
and can eliminate secondary operations that are useless during the process. They are
used in drilling air holes in vacuum molds, drilling radial ports in door closers, milling oil
grooves and act as a low cost spindle for dedicated machines.
They are designed for the efficient transmission of power and motion between
intersecting shafts at right angles. They can be of two types, ground spiral miter gear
and spiral miter gear. They give smoother, quieter operation. They handle higher speeds
and greater torque loads. They provide a steady ratio.
8/8/2019 Gears Types
19/20
Applications
Miter gears are also used in printing, agriculture, bottling, and material handling and
steering. They are used in various industrial sectors including-coal and mining, oil
exploration, paper mining, chemical industry. They are used as important parts of
conveyors, elevators and kilns.
15- Non-Involute Gears
Non-involute gears have reduced specific sliding. Reduced gear sliding has an affect on
low speed meshes, where sliding losses predominate. The efficiency of these gears is
also increased by the use of less viscous oil.
8/8/2019 Gears Types
20/20
The tooth profile geometry is uniquely defined by the arc shaped path of contact. The
gears manufactured by the same rack cutter have the concave convex mesh. The result
of enlarged reduced radius of curvature has as a consequence reduced pressure andbetter lubrication conditions. The geometry of non-involute gear tooth provides
substantially higher capacity than any other gearing.
The disadvantages of the non-involute gearing are lower transverse contact ratio and
great sensitivity to the center distance accuracy.