19

KNIVES & BLADES INSTALLATION ACCESSORIES

MEASURE/MARK & TRIM

5

1

SCRAPERS & BLADES

4

17

HANDLED SQUEEGEES

6

SQUEEGEE ESSENTIALS

10

PPF/WRAPS/VINYL & GRAPHICS

13

HARD CARDS

15

TUBE SQUEEGEES

16

20

SPRAYERS & ACCESSORIES

21

CLEANING/PREP & CHEMICALS

23

SLITTERS & ACCESSORIES

24

METERS

CONTENTS

KNIVES & BLADESSTANDARD 9MM KNIVES

MULTI BLADE CARTRIDGE KNIVES

GT126 OLFA “SILVER” SS KNIFEThe original Olfa stainless steel knife.

GT027 NT PRO A1 “RED DOT” KNIFERegarded by many installers as thefinest professional knife available. Theblade can be advanced in 1/2 segmentincrements for precision control. Rightor left hand use. Now includes astainless steel blade.

GT226 OLFA “SILVER 2” KNIFESignificantly improved over the original “Olfa Silver”. Features right or lefthanduse, blade position auto-lock, and one-segment click-action.

GT127 OLFA A1 KNIFEUsed for film pattern cutting andtrimming. Features a molded plastichandle for maximum control andcomfort. Right or left hand use.

GT227 OLFA XA1 ERGONOMIC KNIFEThis ergonomically correct knifefeatures a comfortable rubber grip for better control and less fatigue.

GT1018 NT A250RP AUTO-LOCK KNIFEChemical-resistant and heat-resistantpolypropylene grip. Ratchet auto-lockslider locks blade in place whilecutting. Right or left hand use.

GT026 NT INJECTOR KNIFEUsed for film pattern-cutting andtrimming. Holds five blades forautomatic blade replacementcapabilities.

GT984 NT A1000RP KNIFECartridge cutter with aluminum die-cast grip. Cartridge holds up to 5 blades.

GT114 OLFA PA2 PRO-LOAD KNIFEHolds up to five blades at a time givingyou 65 new cutting segments per load.

GT1054 NT A300GR KNIFEAll-purpose standard duty utility knife with stainless steel sliding holder and sturdy aluminum die cast grip for longlasting use. Ratchet auto-lock sliderlocks blade in place while cutting. End cap also functions as a bladesnapper. Designed for either left or right handed use with simplereversal of blade.

GT124 PLASTIC UTILITY KNIFEUsed for film pattern cutting and trimming.

NOTEAll knives are packed with a carbon steel blade except theGT126, GT226 & GT027 which include a stainless steel blade.

KN

IVES &

BLA

DES

1

KNIVES & BLADES CONT’D

KN

IVES &

BLA

DES

2

30° KNIFE & BLADES

GT1051 OLFA SAC1 KNIFESlim stainless steel body with a 30°angle blade for precision in patterncutting. Great for graphics and paintprotection. Use GT1052 replacement blades.

GT1052 OLFA A1160B 30° CARBON BLADESStandard duty acute angle snap-offblade for use when precision is a must.Seven cutting edges per blade strip.Pack of 10.

STANDARD 9MM BLADES

GT115 OLFA AB10S STAINLESS STEEL SNAP BLADESPack of 10. The industry standard whenit comes to snap blades for film andpattern cutting. Thirteen cutting edgesper blade. Use in most standard dutyknives.

GT116 OLFA AB50S STAINLESS STEEL SNAP BLADESPack of 50.

GT123 OLFA AB50B CARBONSNAP BLADESStandard carbon snap blades withsuperior sharpness and edge retention.This 9mm blade fits most standardduty knives and has 13 cutting edgesper blade. Pack of 50.

GT1031 OLFA ULTRAMAX ABB50BCARBON SNAP BLADESThese blades are double-honed forextreme sharpness and are 25%sharper than the standard duty carbonblade. Eight cutting edges per blade,50 blades per pack. Fits most standard Olfa knives.

GT262 KDS SB-50S EVOSTAINLESS STEEL SNAP BLADES13pt snap off blade. Pack of 50.

GT115

GT116 GT1031

GT123

GT266 KDS SB10-EVO13pt snap off blade. Pack of 10.

GT1020 NT BA50P STAINLESS STEEL SNAP BLADESStainless steel snap blades from themakers of the “Red Dot” knife. Use in9mm and multi-blade cartridge knives.Pack of 50.

ANY BLADE CANCUT ORSCRATCH GLASS!It depends on theglass, edge of theblade and the angle of the cut. No matterwhat knife or bladeyou use, be sure to use a SHARP bladeevery time!

GT1021 BL50P BLADESHeavy-duty NT blades for use with theGT1019, GT111, & GT264. Pack of 50.

3

KN

IVES &

BLA

DES

GT264 KDS L22 GRIPFIT AUTOLOCK KNIFEHeavy-duty knife with comfortablegrip. Use with any 8pt blade to cutwindow films 7 mil or greater.

GT1019 NT L500GRP KNIFENT heavy-duty knife with ratchet auto-lock slider which locks the blade intoplace while cutting. Blade storage inhandle. Use with 7 mil or greater films.

GT111 8PT AUTO LOCK KNIFEHeavy-duty knife with breakawaypoints for use with security films 7 milor greater. Blade storage in handle.

KNIVES & BLADES CONT’D

GT263 KDS LB50BH POWER BLACK8PT BLADESIdeal for thicker films, 7 mil or greater.Fits GT111, GT264 & GT1019. Pack of 50.

GT2016 KDS GB50BH POWER BLACKG-BLADESThe G-Blade is a double-honedextremely sharp 8pt blade that is idealfor cutting safety and security film. FitsGT111, GT264, & GT1019. Pack of 50.

GT131 8PT BLADES18mm replacement blades. Fits GT111,GT264 and GT1019. Pack of 5.

GT112 OLFA LBB50B ULTRAMAX 8PT BLADESReplacement blades for GT111, GT264& GT1019 heavy-duty knives. Triple-honed for extremely sharp edge. Idealfor cutting thick films, 7 mil or greater.Pack of 50.

GT263

GT2016

8PT HEAVY-DUTY KNIVES & BLADES

TOOL TIPTry the most popular knife and blade option for the various applications:

- Automotive/Residential Window Films use GT126/GT027 (pg. 1)and GT116/GT1020 (pg. 2)

- Paint Protection use GT1051 and GT1052 (pg. 2)

- Vinyl Graphics use GT026/GT114 (pg. 1) and GT123 (pg. 2)

- Safety and Security Films use GT1019 (pg. 3) and GT112 (pg. 3)

GT108 6" TRIUMPH CARBON BLADESCarbon steel offers strong capablescraping that lasts longer thanstainless steel blades but rust moreeasily. Use these blades for scrapingadhesive and other debris from glasssurfaces. Double edged for morescraping per package. These blades fit any of the standard 6" TriumphScrapers. (0.20 mm x 6") Pack of 25.

GT108SS 6" TRIUMPH STAINLESSSTEEL BLADESLong lasting rust resistant stainlesssteel blade. Perfect for removingadhesive and other debris from glasssurfaces. The double edge blade offersyou more scraping than other blades.(0.15 mm x 6") Pack of 25.

GT108SS-HD 6" TRIUMPH STAINLESSSTEEL HEAVY-DUTY BLADESThis rust resistant stainless steel bladeis thicker and stronger than thestandard 6" Triumph Stainless SteelBlades. A must have for those toughfilm removal jobs. A new productexclusively for the tinting industry. A must have for all residential andcommercial installers. (0.20 mm x 6")Pack of 25.

6" SCRAPERS & BLADES

4

SC

RA

PER

S &

BLA

DES

GT107 6" TRIUMPH SCRAPERLightweight and maneuverable.Includes cover and one doubleedged blade.

GT107A 6" ANGLED TRIUMPH SCRAPERThe handle is tilted at a 30° angle.Includes cover and one doubleedged blade.

GT107PC 6" TRIUMPH SCRAPERWITH SLIDE COVERThis is the new and improved versionof the slide covered Triumph. With abigger button and smoother action,the cover easily opens and closes withno hassle. No more fumbling with aseparate blade cover while doingladder work. Great for regular windowcleaning, but not recommended forstripping off old film.

GT983 6" ERGONOMICTRIUMPH SCRAPERAn improved version of the angled 6" Triumph scraper with a morecomfortable grip. Includes cover and one double edged blade.

GT983A 6" ANGLED ERGONOMICTRIUMPH SCRAPERAn improved version of the standard6" Triumph scraper with a morecomfortable grip and tilted handle.Includes cover and one double edgedblade.

GT106 6" RED HEAVY-DUTYScraper ideal for film removal. Includescover and one double edged blade.Use GT110 as replacement blades.

GT110 TRIUMPH HEAVY-DUTYCARBON BLADESReplacement blades for the RedHeavy-Duty Triumph Scraper (GT106).This thicker blade (0.40 mm) offersgreater strength for those tough jobs. Pack of 10.

GT110

GT106

NOTEAll scrapers are packaged with a carbon blade.

SCRAPERS & BLADES

GT2023

GT140

GT140-12GT139

5

SC

RA

PER

S &

BLA

DES

GT104 4" SCRAPER WITH EXTENDED HANDLE4" scraper with extended handleallowing for better leverage. Use withGT105 or GT1007 as replacementblades. Blade cover included.

GT1023 AL PRO 4" STRIPPERThis 4" scraper has an adjustable headas well as an adjustable knob for twohanded use. Blades can be storedinside the handle.

GT105 4" CARBON SCRAPER BLADESFits the GT104 and GT1023. (0.017mm x 4") Pack of 10.

GT1007 4" CARBON SCRAPER BLADESFits the GT104 and GT1023. (0.017mm x 4") Pack of 100.

SCRAPERS & BLADES CONT’D

4" SCRAPERS & BLADES

3" SCRAPERS & BLADES

1" SCRAPERS & BLADES

GT210 3" TRIUMPH SCRAPERSmaller version of the regular Triumph.Designed to fit perfectly into corners.

GT211 3" TRIUMPH CARBON BLADESUse in 3" Triumph Scraper (GT210).(0.20 mm x 3") Pack of 10.

GT109 1" CLIP SCRAPERGT109S 1" CLIP SCRAPER WITHTHUMB SCREWThese effective scrapers willaccommodate standard or stainlesssteel 1" single edge blades as well asGT139 plastic razor blades. Try the Lil Chizler in these handles for more leverage.

GT138 HEAVY-DUTY 1" RAZOR SCRAPERGT138HYDE HYDE 1" RAZOR SCRAPERRetractable safety scraper;intermediate blade position keeps theblade from sliding out while in use.

GT212 1" NEON MINI SCRAPERHolds 1" single edge blade.Use with GT140, GT140-12 & GT137.

GT994 BIG BLADEJumbo size plastic razor blade perfectfor cleaning & film removal.(3" x 4")

GT140 1" SINGLE EDGE BLADESUse in any 1" blade holder. #9 Carbonsteel single edge blade, non-rustaluminum back. (.009"/.2286 mm)Pack of 100.

GT140-12 #12 1" SINGLE EDGE BLADESUse in any 1" blade holder. #12 Carbonsteel single edge blade, non-rustaluminum back. (.012"/.3048 mm)Pack of 100.

GT137 1" SINGLE EDGE STAINLESSSTEEL BLADESUse in any 1" blade holder. Stainlesssteel, uncoated. (.009"/.23 mm)Pack of 100.

GT2023 SCRAPERITE PLASTICRAZOR BLADESThese plastic razor blades are doubleedged and safe for glass. Great forremoving adhesives from window filmsand vinyl decals. Pack of 100 blades.

GT139 PLASTIC RAZOR BLADESPerfect for removing leftover film andadhesive from surfaces that are easilydamaged, such as rear windowdefrosters or other sensitive glasssurfaces. Pack of 100.

GT105 GT1007

GT109 GT109SGT138 GT212

GT994GT138HYDE

TOOL TIPPlastic razor blades are the mosteffective way to safely prepautomotive glass. Although the bladesare plastic, proceeding with caution isalways a good idea.

HANDLED SQUEEGEES

6

HA

ND

LED

SQ

UEEG

EES

GT042 8" SILVER SECURITY SQUEEGEEComfortable, ergonomic handle isdesigned especially for security filminstallation. Comes equipped with theGT041 blade. Curved handle appliesmore pressure to surface, reducingfatigue and ensuring easier, betterinstallations. Blade is replaceable witheither the Security Squeegee (GT041),Flatfoot (GT059), Pro Squeegee(GT061), or Orange Crush (GT259)blades.

GT041 8" SILVER SECURITYSQUEEGEE BLADEStandard replacement blade for GT042.

GT059 8" FLATFOOT SQUEEGEE BLADEGT069 6" FLATFOOT SQUEEGEE BLADESpecially angled blades for the ProSqueegee (GT062 or GT064). Theangle is designed to maximize thesurface area in contact with the film,thereby removing much moremounting solution than a standard Pro blade with a square edge. Beveled edge.

GT061 8" PRO SQUEEGEE BLADEGT063 6" PRO SQUEEGEE BLADEReplacement blade to Pro Squeegee(GT064 or GT062) used as a means ofremoving application solutions frombeneath the film during the installationof all flat glass film types. Square edge.

GT042 GT069

GT061

GT063

GT059GT041

GT062 6" PRO SQUEEGEE DELUXEGT064 8" PRO SQUEEGEE DELUXEAn installation squeegee as a ready-to-use assembly. Used to removeapplication solution during theinstallation of all flat glass film types.

GT056 18" SQUEEGEE & CHANNELGT055 12" SQUEEGEE & CHANNELGT054 8" SQUEEGEE & CHANNELGT053 6" SQUEEGEE & CHANNELStainless steel channel and soft rubbersqueegee blade insert for use with theUnger Pro Handle (GT050 or GT050E).Used in the flat glass cleaning processand in the final cleanup after the filminstallation to remove soap streaks or smudges.

GT252 6″ EXTRUDER CHANNELGT253 8″ EXTRUDER CHANNELThis new channel works in yourexisting Unger handle or the NEWGT050A (pg.8). It is designed to give the blue squeegee blade(GT118) added stiffness and a betterangle to aid in laying down the filmand extracting more water persqueegee pass.

GT062 GT056

GT055

GT054 GT252

GT253GT053

GT064

GT045 140" SQUEEGEE BLADEGT048 12" SQUEEGEE BLADEGT049 18" SQUEEGEE BLADEReplacement blades for Ungersqueegee channel. Use for windowcleaning, not installation.

GT1001 UNGER 42" HARDREPLACEMENT BLADEHard replacement rubber is ideal forwarmer working conditions and foroptimum liquid removal on large,flat surfaces.

NEW

GT045GT048GT049

GT205 THE BULLDOZER I -AUTOMOTIVEAllows you to get to those hard toreach areas, such as behind speakers,brake lights, low angles and rearwindows. Features a 6" squeegeeblade and is 15" in overall length.

GT206 THE BULLDOZER II - FLAT GLASSFeatures reinforced ribs on the backside for extra rigidity and leverage.Includes 6" squeegee blade and is 15"in overall length. The BulldozerSqueegees have a new rubbercompound for less slip resistance, aflatter blade for better water extractionand added plastic under the bladecorners for additional strength.

GT1006 THOR’S HAMMERUse for 6-mil+ safety film installations,and final pass on slow drying thin films.(Flat Glass Applications). Use GT117Cas a replacement blade.

GT117C SQUARE BLUE MAX-NARROWReplacement Blade for GT1006Thor’s Hammer.

GT985 PERFORMAX HANDLEIdeal for water extraction when usedwith GT117, GT117B, GT203 or GT257.Features a socket that acceptsstandard broom or paint rollerextensions. This allows installers to get more leverage.

7

HA

ND

LED

SQ

UEEG

EES

HANDLED SQUEEGEES CONT’D

GT050 UNGER PRO (LATCH) HANDLEThe original Unger Pro Handle. For usewith the GT053, GT054, GT055 orGT056 stainless steel channels withblack rubber for cleaning or bluereplacement blades (GT118) for installation.

GT050E UNGER ERGOTEC(SPRING) HANDLEFeatures a spring mechanism for quickblade changing and a finger indent onthe top of handle for complete control.For use with GT053, GT054, GT055 orGT056 channels with black rubber forcleaning or blue (GT118) for installation.

GT034 WHALE TAIL SQUEEGEEGreat for getting behind brake lightsand back window applications.

GT035 WHALE TAIL REPLACEMENTBLADE

GT036 WHALE TAIL HANDLE

GT208 SIDE SWIPER HANDLE ONLYGT207 SIDE SWIPER WITH BLADEA great tool for the lower edge of rearwindows and behind brake lights. UseGT118-6 as a replacement blade.

GT118 BLUE SQUEEGEE REFILL(6", 8", 12", 18" OR 120" ROLL)Use in the Unger squeegee channel asa finishing squeegee for maximumwater removal. Replacement blade forGT207. Use with GT252 or GT253Extruder Channels (pg.6).

GT050GT050E

GT205

GT206

GT208

GT207GT118

GT1042 TITAN SQUEEGEE-REDThe Titan is made with the sameplastic used to make bullet proof glass.This allows more strength and rigidity.The overall length is 14 3/4" whichallows a longer reach for rear windowsand its unique design will easily liftinner and upper door seals.

GT043 BIG FOOTSpecifically designed to remove waterfrom the lower portion of rearwindows. Features a flex-firm blademolded right into the long flattenedtennis racquet-style handle. The handleis wrapped with genuine Head SofTactraction grip material. Reaching thelower deck of back windows is not aproblem with Big Foot. This toolmeasures a full 15" from blade tip tohandle end.

GT040 SLIM FOOTModeled after the Big Foot Squeegee,the Slim Foot has a slender design thatcan reach into tighter openings. Thisno rib squeegee helps reach behindbrake lights and has a rubber grip forsecure handling. Measures 15" fromblade tip to handle end.

HARDES

TSOFTEST

◊◊◊◊◊◊◊◊◊◊◊◊◊◊◊

DUROMETERLEGEND

GT117C

GT1006

◊◊◊

HANDLED SQUEEGEES CONT’D

HA

ND

LED

SQ

UEEG

EES

8

GT117-8 8" BLUE MAX SQUEEGEEThe favored Blue Max installationsqueegee is now available in 8" makingit perfect for flat glass installs! Use thisblade in the 8" Fusion Handle(GT1046) for great water extraction.

GT1046 8" FUSION HANDLEIdeal handle for all residential andcommercial applications. Holds the 8" Orange Crush Squeegee Blade(GT259) and 8" Blue Max Squeegee Blade (GT117-8).

GT1047 5" FUSION HANDLEGT1058 5" FUSION HANDLE - SHORT HANDLEThese handles are designed tooptimize your leverage in removingmounting solution. Great for highperformance automotive films andsmaller residential windows. Thesehandles accommodate the OrangeCrush, Blue Max and Super Clear Max Squeegees.

GT259 8" ORANGE CRUSHGT258 5" CROPPED ORANGE CRUSHGT257 5" ORANGE CRUSHThese blades help expel water whilekeeping their strength. The OrangeCrush conforms to curved glass.Blades fit into a handled grip or can be used alone.

GT122 BLUE MAX SQUEEGEE WITH HANDLE

GT204 SUPER CLEAR MAXSQUEEGEE WITH HANDLEReady-to-use installation squeegee.The specially modified Unger handlemakes these installation squeegeesmust haves. The handle is soldseparately as GT050A. Replacementblades are available as part numberGT203A and or GT117A. For extraleverage, use with a GT030 Motus DGrip found on pg. 17.

GT203 SUPER CLEAR MAXSQUEEGEE BLADE

GT203A ANGLED SUPER CLEAR MAXSQUEEGEE BLADESofter version of the Blue MaxSqueegee, more flexible for backwindow installations.

GT050A UNGER (SCREW) HANDLEA modified Unger handle that hasproven results for maximum waterextraction. For flat glass applicationsuse with the new Extruder channels(GT252 & GT253 on page 6). Thehandle also works excellent with SuperClear Max, Blue Max and Orange Crush Squeegees.

GT117 BLUE MAX 5" HAND SQUEEGEEInstallation squeegee for automotiveand flat glass applications. Harder thanGT203; great for water removal.

GT117B SQUARE BLUE MAX 5" HAND SQUEEGEEIdeal for installing security film.

GT117A ANGLED BLUE MAX 5"HAND SQUEEGEEInstallation squeegee for automotiveand flat glass applications. Harder thanGT203, these tools are excellent forwater removal.

GT117-8GT1046 GT1047

GT1058

6"6"

Beveled Edge

3.5"

◊◊◊

GT204GT122◊◊◊

GT203◊◊ GT203A

◊◊◊◊

Square Edge

GT117◊◊◊

GT117B◊◊◊

GT117A◊◊◊

HARDES

TSOFTEST

◊◊◊◊◊◊◊◊◊◊◊◊◊◊◊

DUROMETERLEGEND

GT259

GT258

GT257◊◊◊

◊◊◊

◊◊◊

NEW

HA

ND

LED

SQ

UEEG

EES

HANDLED SQUEEGEES CONT’D

9

GT153Y GRIP-N-GLIDE YELLOW (FLEX-FIRM)GT153O GRIP-N-GLIDE ORANGE (SOFT)Grip-N-Glide combines an ergonomic handgrip with high-performance, interchangeable blades to give you just whatyou need for tint, wrap and PPF installations.

GT154Y GRIP-N-GLIDE YELLOWREPLACEMENT BLADE (FLEX-FIRM)

GT154O GRIP-N-GLIDE ORANGE REPLACEMENT BLADE (SOFT)Unlike tube squeegees with their belt-sanded round edges,the Grip-N-Glide features a .24" thick squeegee blade withFrench edges that are machine milled for maximum waterextraction. And you can use either the firm yellow 90A orsofter orange 85A blade to meet your application needs.The blades fit snugly into a frame that is covered by asubstantial handgrip designed with comfortable fingergrooves and a special surface texture to provide theultimate control in either wet or dry use.

GT2056B GO DOCTOR BLUE (HARD)GT2056Y GO DOCTOR YELLOW (FLEX-FIRM)GT2056R GO DOCTOR RED (SOFT)A fully integrated squeegee system where all of thecomponents have been designed together, to worktogether. The I-beam handle fits comfortably in your hand.The I-beam handle is wrapped with a comfortable, non-slipmaterial that provides secure grip. Go Doctor incorporates aquick-change blade system for speedy on the jobreplacements.

GT2057B GO DOCTOR BLUE BLADE (HARD)Use for window film and auto wrap installs.

GT2057Y GO DOCTOR YELLOW BLADE (FLEX-FIRM)GT2057R GO DOCTOR RED BLADE (SOFT)Use for window film, auto wraps, vinyl graphics and paint protection installs.

GT1022 STROKE DOCTORGT1022B STROKE DOCTOR REPLACEMENT BLADEDesigned with an I-beam construction handle thatfeatures an ergonomic slip-resistant grip and longerblade to apply squeegee pressure more evenly in themost hard to reach places.

GT153Y

GT2056B

GT1022GT1022B

GT2057B GT2057Y GT2057R

GT2056Y GT2056R

GT153OGT154Y GT154O◊◊

◊◊◊ ◊◊ ◊

◊◊◊ ◊◊ ◊

◊◊◊ ◊

10

SQUEEGEE ESSENTIALS

GT995 WHITE KNIGHT SQUEEGEELarge squeegee with narrow handleallowing for better reach.

GT066 6" CLEAR SUPER SQUEEGEEIdeal for general purpose squeegeeing.The consistency of the materialproduces great results with minimaleffort.

GT067 3" CLEAR SUPER SQUEEGEEWorks best on corners, edges andbubbles allowing maximum pressure to be applied with minimal risk ofdamage to your work.

GT091 SLAMMERUsed for cleaning corners and along gaskets, wicking water out along borders and easily reaches rear windows.

GT092 SHUTTLEA hard card with the ability to reachinto tight areas located at the bottomedge of rear window glass.

GT068 HARD CARD SHARPENERA must have to keep hard card andother squeegee edges smooth. Uses 9mm replacement blades.

GT088 BONDO SQUEEGEEFlexible and soft card style squeegee.Great for third brake light installs.

GT202 THE CONQUERER SQUEEGEEGT202B THE BLUE CONQUERERSQUEEGEEThe Conquerer is the original cornerreach tool. Features a soft squeegeeblade along one edge and pointedhard card tips on the ends making it aversatile staple to any tool kit. Use theBlue version for a harder blade.

GT149 12" BLOCK SQUEEGEEGT148 6" BLOCK SQUEEGEECombination squeegee/hard card usedfor finishing during film installations.Can be cut to various angles to reachtight, sharp corners.

GT032Y TAIL FIN YELLOW (FIRM)GT032G TAIL FIN GREEN (SOFT)Great for getting behind brake lightsand back window applications. Finger holes make holding onto the Tail Fin easy.

GT091

GT068

GT088

GT202GT202B

GT092

SQ

UEEG

EE E

SSEN

TIA

LS

◊◊

GT032Y◊◊

◊

GT032G◊

◊

GT149GT148

GT083 LIL CHIZLERGT083Y DURA CHISELGT083W CHIZZLERIdeal for removing decals, film or adhesive from sensitivesurfaces. Use for pressing down small film creases or airbubbles. The White Chizzler is slightly larger, has thickeredges and is harder than the original pink Lil Chizler or the Yellow Dura Chisel.

GT1049 GATOR BLADE IGT1050 GATOR BLADE IIThe Gator Blade I and Gator Blade II products arealternatives to the Lil Chizler. Each has a unique shape togive you a better grip making it easier to apply pressure.

GT083◊◊◊

GT083Y

GT1049◊◊◊

GT083W◊◊◊◊ GT1050

TOOL TIPThe Tail Fin (GT032) is a greattool for squeegeeing behindrear brake lights.

SQ

UEEG

EE E

SSEN

TIA

LS

11

SQUEEGEE ESSENTIALS CONT’D

HARDES

TSOFTEST

◊◊◊◊◊◊◊◊◊◊◊◊◊◊◊

DUROMETERLEGEND

GT201G GREEN CONTOUR (SOFT)GT201Y YELLOW CONTOUR (FLEX-FIRM)GT201PLT PLATINUM CONTOUR (HARD)Gives you curves where you need them. Designed to matchall those concave surfaces installers see every day. A greatfit for window film, paint protection or vinyl installs. TheContour hugs surfaces evenly while spreading radialpressure outward for quick film adhesion. The elongatedtriangular shape gets in to all those hard to reach areas.

GT113W WHITE DIAMOND TIP (HARD)GT113Y YELLOW DIAMOND TIP (SOFT)Designed to meet the challenge of hard to reach areas, withsquare edges and 20° angled corners on both sides. Theraised area in the center gives you a secure, slip-resistantgrip, even when wet. The softer version makes a greatsqueegee because of the firm texture delivering pressure tothe point-of-contact while the special material helps preventscratching. Ideal for bumping edges and heat shrinkingbecause of the high heat-resistant material.

GT256 POWER STROKE YELLOW (SOFT)GT254 POWER STROKE BLUE (HARD)The original hand held molded squeegee, designed to fitcomfortably in your hand. Measures 5.7" from tip to tip.Blue has a durometer for the ultimate in moisture removal,especially for sputtered films. Yellow works well with dyedfilms and first pass on metal films.

GT151W WHITE QUICK FOOT (FLEX-FIRM)GT151B BLUE QUICK FOOT (SOFT)GT151Y YELLOW QUICK FOOT (HARD)A stiff squeegee with a handle for jobs that require mediumreach. Slim and trim with an unwrapped handle. Comes in avariety of flex ratings to meet a wide range of applications.

GT201Y◊◊

GT201G◊

GT256◊

GT201PLT◊◊◊

GT254◊◊◊

GT113W◊◊◊◊

GT113Y◊◊◊

GT060 EZ WING LIME (FLEX-FIRM)GT060W EZ WING WHITE (SOFT)The first difference in the EZ Wing from a product like theEZ Reach or EZ Reach Ultra is the unique chizzler tip thatenables you to flip it over to chisel out those stubborncreases or dust spots. The second feature of the new EZWing is the increased stiffness across the nose of the tool.This will allow you to apply more pressure out at the tip inthose situations where you are reaching into a tight spot.Lastly the CCT technology provides a curved main edge.

GT044B LITTLE FOOT BLUE (SOFT)GT044R LITTLE FOOT RED (FLEX-FIRM)GT044BLK LITTLE FOOT BLACK (HARD)The Little foot features the unique blade shape of the BigFoot without the handle. Fits comfortably in your hand andfeatures an angled, long-reach tip that gets behind gasketsand rubber seals easily. This squeegee measures about 6"(15 cm) along the usable edge. The pointed edge of this toolallows the installer to squeegee in very tight areas. Hasplenty of room to keep a good grip on the squeegee.

GT151WGT151B

GT044BGT044R

GT044BLK

GT151Y

◊◊◊

◊◊◊

◊◊◊

◊◊◊

TOOL TIPCCT- Control Contour Technology found in the newEZ Wing (pg.11) and Speed Wing (pg.15) product linesenables the tool to encourage a finger or bubble todisperse outward reducing the chances of a crease.

NEW GT060

GT060W

◊◊ ◊

GT1025PLT REBEL-PLATINUM (HARD)GT1025M REBEL-MANGO (FLEX-FIRM)A hybrid of the bump card and Diamond Tip. Great as anapplicator or use as a trim guide on flat glass. Rebel has aunique diagonal shape, reaching corners easily. The parallelgrip ridges make holding onto the Rebel easy and they areavailable in two flex ratings to cover a multitude ofinstallation needs.

GT1070 PLATINUM SMART CARDZThe modern version of the hard card squeegee, only better!25% wider than a hard card, with a tapered tip, comfortablegrip and thin squeegee edge make it the smartest tool inyour apron. Great for sliding under gaskets and seals. UseSmart Cardz anywhere you would use hard card squeegees.

GT200 EZ REACH ULTRA GOLD (FLEX-FIRM)GT200PLT EZ REACH ULTRA PLATINUM (HARD)If you like the Original EZ Reach, you are going to love Ultra!It is exactly the same except the hole has been removed tomake it stronger and the top has been trimmed down togive installers yet another handy angle to work with.Designed specifically to get at the corners of quarter glasswindows, you will also reach for it again and again to putdown those little corners of film in hard to access areas.

GT2003 ORIGINAL EZ REACH GOLD (FLEX-FIRM)GT2003PLT ORIGINAL EZ REACH PLATINUM (HARD)Stop cutting down hard card squeegees and use thisversatile tool instead. These triangular cards with flat edgesare perfect for putting down those little corners of film inhard to access areas. The gold version is flex-firm while theplatinum offers a hard card texture with internal lubricationtechnology to help prevent scratching. EZ Reach is theultimate corner tool.

GT2042B TRI-EDGE BLUEGT2042Y TRI-EDGE YELLOWGT2042O TRI-EDGE ORANGEGT2043 TRI-EDGE PLUSTri-Edge is the new standard in the industry. Tri-Edge Plusfeatures a rubber squeegee edge. (Hardness is in order ofsoftest to hardest: Blue, Yellow, Orange)

GT2063P TRI-EDGE X PINKGT2063B TRI-EDGE X BLUEGT2063Y TRI-EDGE X YELLOWGT2063O TRI-EDGE X ORANGETri-Edge is now premiering the Tri-Edge X. The angles have been recalculated and extended into a bigger tool. All the durability and quality of the Tri-Edge tool is nowmade to make those deep gaskets and hard to reach spots more accessible.

12

SQUEEGEE ESSENTIALS CONT’D

SQ

UEEG

EE E

SSEN

TIA

LS

HARDES

TSOFTEST

◊◊◊◊◊◊◊◊◊◊◊◊◊◊◊

DUROMETERLEGEND

GT1025PLT◊◊◊

GT2003◊◊◊

GT2042B◊

GT2063P◊◊

GT2063B◊

GT2063Y◊◊

GT2063O◊◊◊

GT2042Y◊◊

GT20420◊◊◊

GT2043◊◊◊

GT2003PLT◊◊◊◊

GT200PLT◊◊◊◊

GT200◊◊◊

GT1025M◊◊

NEW

NEW

TOOL TIPThe GT2043 Tri-Edge Plus utilizes a rubberized heat-resistant material on one edge to serve as a watersqueegee. The new GT2063P Tri-Edge X Pink is madeof a rubberized heat-resistant material and is used tosmooth film in hard to reach places. Both squeegeeswork best on wet surfaces.

13

PPF/W

RA

PS/V

INY

L &

GR

APH

ICS

PPF/WRAPS/VINYL & GRAPHICS

GT2017 FINISH LINE KNIFELESS TAPEThe Knifeless Tape has a high strengthfilament that creates a clean sharp cutwithout the risk of damaging paintedsurfaces. (50m/ 164' roll)

GT2078 PPF KNIFELESS TAPE Create your own PPF patterns with this5MM wide, ultra fine, ultra sharpfilament sandwiched between twotapes plus a cover tape.(50m/ 164' roll)

GT2021 12YD. SLIP TAPEGT2021-4 4YD. SLIP TAPESlip tape is the ultimate product formaking your application squeegeessmoothly and safely glide acrosswindow film, paint protection, car wrapand vinyl graphic applications. Avoidtearing or scratching the material youare working with. Include this productin your tool box!

GT237 SUNNY TUCKERThis wrap tool provides multi-functionality use by allowing theinstaller to reach edges and body lineslike never before. This tool is a musthave if you apply any graphics tochallenging surfaces.

GT1000 MACTAC FELT SQUEEGEERecommended for paint protection orvinyl graphic installations. The soft feltis designed to avoid scratching.

GT1010 3M WET OR DRY SQUEEGEESoft rubber card style squeegee.Recommended for paint protectioninstallations.

GT2002 4" MAGNETIC BLACK BONDOMagnetic bondo squeegee is great for the application of car wraps,cutting window film patterns, and vinyl graphics. The strong magnetsallow you to hold the material in place in addition to holding your knife for easy access.

GT1065 4" LIDCO FELT SLEEVEA felt wrap for any 4" hardcard squeegee.

GT1064 4" BUMP CARD WITH FELT EDGEFour inch hard card with two ridges or“bumps”. One edge is wrapped in felt.

GT2021GT2021-4

SC2 SOOPER CLIP (2 PACK)SC50 SOOPER CLIP (50 PACK)Faster and easier than tape or rubberbands. These brightly colored SooperClips are designed for efficiency.

ER1 EMBLEM REMOVAL TOOLThis tool is used before the vehiclewrap/vehicle graphic application toremove emblems, logos and badgesfrom your vehicle. Our EmblemRemoval Tool comes with customdesigned ergonomic handles that are comfortable to use.

RB RIVET BRUSHMade of stiff bristle synthetic fiber, therivet brush for fleet graphic installershelps form flexible cut and printedvinyl over the rivet surface.

NEW

NEW

NEW

NEW

NEW

TOOL TIPFelt edge tools are becoming increasingly popular due to the changes in the industry.From Car Wraps, Vinyl Graphics, to Paint Protection films there is a felt product formost applications. Check out the newest growing selection of products.

SC2SC50

N OW C O M E S W I T H F E LT N OTI N S TA L L E D . E X T R A F E LT I N C L U D E D .

14

PPF/WRAPS/VINYL & GRAPHICS CONT’D

PPF/W

RA

PS/V

INY

L &

GR

APH

ICS

GT2005 MANGO SMART CARD WITH FELTGT2006 MANGO REBEL WITH FELTGT2007 MANGO LITTLE FOOT WITH FELTGT2008 MANGO BUMP CARD WITH FELTGT1085 MANGO PRO PACK WITH FELT (SET)The felt edge makes these the perfect tools for paintprotection, vinyl signs and graphics.

WES WET EDGE SQUEEGEEWrap your vehicles faster and better. The only squeegeeapplicator made to use wet. No scratches, no marks, justsmooth motions that easily glides across vinyl films andpainted surfaces without worry of mistakes or damage. The Wet Edge Squeegee is a Teflon squeegee with a uniquemicrofiber bonded to it. Can be used either wet or dry. This isthe top of the line applicator in the business. Colors will vary.

GT2006

GT2008

GT2007

GT2005

WG1 WRAP GLOVEThe new Wrap Glove is sold in pairs and is a must have foranyone installing vinyl graphics and vehicle wraps. Installingwith your bare hands can cause over stretching andpuckering of the vinyl as well as potential damage from thetransfer of oils on your skin. These lint free and durableWrap Gloves reduce friction while handling the materialgiving you great results every time.

WCKNIFE WRAP CUT LINER KNIFEThe ultimate vehicle wrap knife! The Wrap Cut Knife byImage 1 Impact is made specifically to cut through just the liner side of any pressure sensitive vinyl graphic andwrap film. This knife will only cut through the paper release liner of the vinyl.

WCBLADE REPL BLADES FOR WRAP CUT KNIFEThis is the replacement blade for the Wrap Cut Knife,WCKNIFE. Each blade has 4 available cutting edges.10 blades per pack.

MOLD5 MOLDING & TRIMREMOVAL TOOLSThe kit includes five distinctive toolsfor the easy removal of body fasteners,interior trim pieces, exterior bodymoldings, wheel hub caps, etc. Made from heavy-duty plastic toprevent scratching and damage to vehicle surfaces.MOLD11 NOT PICTURED

BPOP BUBBLE POPPER PENThe Bubble Popper Pen is a must havetool for any vinyl graphics installer orcar wrapper. This tool is used to put apin hole (never a knife slit) into yourvinyl, printed graphics or car wrapwhere a bubble or rivet might be torelease the air and flatten the filmgraphic on to the substrate.

IPEN INSTALLER’S PRIMER PENThe Installer’s Primer Pen is easy tokeep in your tool pouch, pocket, ortool box. Fast and easy to use on allyour applications that require preciseapplication of Primer 94. Works withany brand of vinyl film and can beused anywhere Primer 94 is required.

XMH XTREME MAGNET (SINGLE UNIT)XMH6 XTREME MAGNETS-6 PER BOXThese handy body magnets make applying vinyl and vehiclewraps faster and easier by acting as another hand to holdthe material. You can also use them in the place of maskingtape or pre-mask to position the material on the vehicle.

SQBUFF4 4″ BUFFER SQUEEGEEThese pre-cut buffers fit any standard 4″ squeegee. They are far superior to standard felt strips and will helpprevent scratches to the wrap material during installation.Give your hard plastic squeegees a soft and smooth sidewith the Squeegee Buffer Strip.

WCKNIFEWCBLADE

XMH

XMH6

MOLD5

PURCHASE AS A SETOR INDIV IDUALLY.

NEW

NEW

NEW

NEW

NEW

NEW

NEW

NEW

HARD CARDS

GT087-6GRY 6” LIDCO SQUEEGEEGT086-6Y 6” YELLOW HARD CARD SQUEEGEEGT086-6W 6” WHITE HARD CARD SQUEEGEE

GT2072-4 4″ LIME SPEED WING (HARD)GT2072-6 6″ LIME SPEED WING (HARD)GT2072-8 8″ LIME SPEED WING (HARD)GT2076-4 4″ LEMON SPEED WING (FLEX-FIRM)GT2076-6 6″ LEMON SPEED WING (FLEX-FIRM)GT2076-8 8″ LEMON SPEED WING (FLEX-FIRM)GT2077-4 4″ CHERRY SPEED WING (SOFT)GT2077-6 6″ CHERRY SPEED WING (SOFT)GT2077-8 8″ CHERRY SPEED WING (SOFT)The Speed Wing is designed with “wings” to enable the installer to reach areas typically out of the reach of most bump, bondo, teflon and hard cards. The Speed Wing comes with one flat edge and one curved edge.Speed Wings is made from materials that enable it to slide across most film surfaces easily while maintaining its rigidity to lay the material flat and remove moisture or air trapped underneath. Features new ContourControl Technology.

GT086BLU BLUE HARD CARDGT086PUR PURPLE HARD CARDGT086BLK BLACK HARD CARDGT086W WHITE HARD CARD

GT086PNK PINK HARD CARDGT086GLD GOLD HARD CARDGT086PLT PLATINUM HARD CARD

GT087 YELLOW LIDCO SQUEEGEEGT087GRY LIDCO SQUEEGEEGT099 UNIVERSAL SQUEEGEE

GT079 4” 3M GOLD SQUEEGEEGT080 4” 3M BLUE SQUEEGEE

GT086BLU◊

GT087◊

GT2072-4 GT2076-6GT2077-8

GT087-6GRY◊◊ GT086-6Y

◊GT086-6W

◊◊◊

GT087GRY◊◊

GT079◊◊

GT099◊◊◊

GT080◊

GT086BLK◊◊

GT086PLT◊◊◊◊◊GT086W

◊◊◊

GT086PNK◊◊◊GT086PUR

◊

15

HA

RD

CA

RD

S

NEW

HARDES

TSOFTEST

◊◊◊◊◊◊◊◊◊◊◊◊◊◊◊

DUROMETERLEGEND

GT086GLD◊◊◊◊

GT235 5 1/2" YELLOW TURBO SQUEEGEEGT236 5 1/2" YELLOW TURBO SQUEEGEE BLADE An installation squeegee used to remove applicationsolution during installation of all auto and paint protection films.

GT145 18 1/2" YELLOW TURBO SQUEEGEEGT147 18 1/2" YELLOW TURBO SQUEEGEE BLADE Used for removal of application solution during theinstallation process. You can cut the blade down to smaller lengths if desired.

16

TUBE SQUEEGEESTU

BE S

QU

EEG

EES

GT119 4" BLACK SMOOTHIE TUBE SQUEEGEEGT120 9" BLACK SMOOTHIE TUBE SQUEEGEEGT121 28" BLACK SMOOTHIE TUBE SQUEEGEE Soft black squeegee with gray pvc handle.

GT146 28" BLACK SMOOTHIE BLADE ONLYSqueegee tool used for glass cleaning, sometimes called the “Smoothie”. Economy size (28") usually cut to shorterlengths before use.

GT152 5" RED TURBO BLADEGT150 18" RED TURBO BLADEThe hardest version of the Turbo Blade, used for removal of application solution during the installation process.

GT2053 4.5" GREEN TURBO BLADEGT2004 18 1/2" GREEN TURBO BLADEThe green turbo is perfect for paint protection installs, can be cut down to smaller sizes, and has a durometer(hardness) between the GT146 Black Smoothie and the GT147 Yellow Turbo Blade.

GT1026 3 1/2" SOFT DK. YELLOW TURBO SQUEEGEEGT145S 18 1/2" SOFT DK. YELLOW TURBO SQUEEGEEGT147S 18 1/2" SOFT DK. YELLOW TURBO SQUEEGEE BLADEA soft installation squeegee used to remove applicationsolution during installation of all auto and paintprotection films.

GT119◊

GT1026◊◊◊

GT145S◊◊◊

GT120◊

GT152◊◊◊◊◊

GT2053◊◊

GT150◊◊◊◊◊

GT121◊

GT146◊

HARDES

TSOFTEST

◊◊◊◊◊◊◊◊◊◊◊◊◊◊◊

DUROMETERLEGEND

GT2004◊◊

GT147S◊◊◊

GT235◊◊◊◊

GT145◊◊◊◊

GT236◊◊◊◊

GT147◊◊◊◊

TOOL TIPUse GT2021- Slip Tape (pg.13) on the edge of your turbo blade tomake it slide even smoother across paint protection film or vinyl.

GT194 GASKET PUSH STICKGT194B BLUE GASKET PUSH STICK

GT176 WAIST APRONHeavy-duty waist apron for easyaccess to tools while on the job.

GT1080 ERGODYNE WAIST APRON13 pocket tool apron.

GT194

GT130 GASKET WIZARDThis device is used to carefully pullback gaskets for easy film-to-glassinstallations below the gasket. Rub railsare located at the base of allautomotive door window glass and areused for weatherproofing the openingsbetween the glass and the doorstructure. Many installers find theGasket Wizard helpful, even withoutthe use of the bungee cords.

GT128 CERAMIC SAFETYFILM CUTTERDesigned to deliver rapid, precise cutsfor thick gauge safety films. It isintended for precision pre-cutting onflat, square-edged tables.

GT944 AUTOMOTIVE GLASS EDGE TRIMMERUse along the top edge of roll downwindows for a precise “micro-edge”finish (1/8"). Use GT137 as a replacement blade.

GT033 RED DEVIL SQUEEGEEFlexible squeegee that is greatfor tight corners and maneuveringaround gaskets.

GT191 THE EDGE TOOLA convenient trim guide or use thecurved edge to pull back gaskets.

GT033

17

INSTA

LLA

TIO

N A

CC

ESSO

RIE

S

INSTALLATION ACCESSORIES

GT191GT128 GT944

GT132 HOOK TOOLUse this tool to pull back on rubbergaskets to tuck film below the seal.

GT030 MOTUS D GRIP HANDLEUse with almost any handled squeegeeto give extra leverage.

GT135 BLADEATERDesigned for professional installers, theBLADEater holds your knife safely andsecurely, and allows you to easily snapand discard blades into the replaceablewell. Once the well is full, simply toss the well, blades and all.

GT134 BLADEATER REPLACEMENT WELLReplacement well for BLADEater.

GT1004 OLFA DC4 BLADE DISPOSALBlade disposal unit that can beemptied and reused.

GT194B

GT135GT132

GT030 GT134

GT1080GT176

TOOL TIPTinting automotive windows is progressivelymore challenging. View the different tools toassist you in “tucking” the film under thedoor panel.

TOOL TIPYou don’t want to leave behind discardedblades on a job site for a potential injurylater. Safely snap blades into a disposal unit.

GT251 WAGNER HT3500 DIGITAL HEAT GUNThis model allows you to heat shrink in low or high fan speeds and has avariable temperature setting to finetune the amount of heat needed for a specific application. (120 volt)

GT250 WAGNER HT1000 HEAT GUNStandard heat gun with high, medium,low settings. (120 volt)

GT979 KEVLAR HEAT GLOVES (PAIR)Heat-resistant gloves great for useduring heat shrinking.

18

INSTALLATION ACCESSORIES CONT’D

INSTA

LLA

TIO

N A

CC

ESSO

RIE

S

GT921C JIFFY STEAMER J2WREPLACEMENT BOTTLEReplacement bottle for the J2W JiffySteamer (GT921).

GT921B JIFFY STEAMER J2WREPLACEMENT FUSE

GT921CGT921B

GT2015 JIFFY STEAMER J4000W STEAMBLADEThe J4000W has a large 1 gallon internal water reservoir and provides 2hours of continuous steam before refilling. Go from PREHEAT mode tofull steam power in just two minutes. Has a flexible 7.5' hose for easymaneuverability on the job and an angled 9" aluminum steam head thatconcentrates steam into a targeted area for precise removal. Steam-resistant nitrile gloves included in each unit.(120 volt; alternate voltage available upon request).

GT921 JIFFY STEAMER J2W FILM REMOVERImpact resistant, with a 1300 watt heating element and heats up in twominutes with 2 hours of steaming per filling. Great for removing film andadhesive from vehicle rear windows. (120 volt; alternate voltageavailable upon request).

GT2015 GT921

TOOL TIPJiffy Steamer will help prevent damagingdefroster lines when removing film from rearwindows. Besides making life easier, a Steamerwill pay for itself in just a few jobs when youconsider the considerable time savings.

GT190GRY GREY 5-WAY TRIM GUIDEGT190BLK BLACK 5-WAY TRIM GUIDEGT190WWHITE 5-WAY TRIM GUIDEUse these tools as a trim guide or wrapin paper towels and use as a bumptool. Each of these offers uniqueshapes and corners. The GT190 Whiteeven features a ruler.

GT991 1" RED FILM TAPEGT990 3/8" RED FILM TAPEFeatures low-tack adhesive.Use to retape film rolls for storage. (60.1 yards per roll)

DOTRIX DOT MATRIX VINYL 16"X50'Gives the dot matrix area on cars a smooth finished look. Pressuresensitive adhesive requires no heat shrinking.

GT157 1/2" BLACK OUT TAPEGT158 1" BLACK OUT TAPEGT159 1 1/2" BLACK OUT TAPEBlack matte vinyl used to hide lightgaps along edges of film installations.(150' per roll)

GT981 DO NOT ROLL DOWN STICKERPerfect as a reminder on new autoinstalls. Features low-tack adhesive.(1000 per roll)

GT1096 DO NOT ROLL DOWN TAPEApproximately 200 stickers per roll.

GT972 DIGITAL TAPE MEASUREThis compact meter uses a narrowbeam to measure distances instantly,even through door openings and incrowded rooms. Lifetime lithiumbattery included.

GT078-75 3/4" BLACK ACRYLIC FELTGT078 1 1/2" BLACK ACRYLIC FELTHelps reduce scratching of automotivefilms on some vehicle roll downwindows. (50' per roll)

GT075 YELLOW FILM MARKERHandy for 3 basic purposes: 1) Marking film prior to installation

of windows with unusual shapes (arches, trapezoids, etc.) which must be cut to approximate shapebefore the final “lay-up”.

2)Circling a contaminant (hair or fiber)before pulling back the film to remove it.

3)Marking film edges to check for glassmovement on side roll-ups during thetrimming process. Yellow grease markeasily wipes away.

GT076 FILM OPAQUER PEN - THIN POINT

GT077 FILM OPAQUER PEN - BROAD POINTUsed by installers to hide fine linemistakes in trimming which causeslight intrusion at the film edge.

GT187 12" TRIANGLE45/90° with circle templates.

GT186 8" TRIANGLE30/60° with circle templates.

GT183 18" STRAIGHT RULERGT182 36" STRAIGHT RULERImperial measurements including1/8ths & 1/16ths.

GT190GRYGT991

GT990

GT158

GT157

19

MEA

SU

RE/M

AR

K &

TR

IM

MEASURE/MARK & TRIM

GT981

GT1096

GT190BLKGT190W

GT159

GT078-75 GT078

GT186

GT077

GT187

GT076

GT183 GT182

TOOL TIPIn addition to a trim guide, the GT190 5-Way Tools are also an effective squeegee,especially when wrapped with a low lintpaper towel or cloth to absorb moisturealong the border of the film.

TOOL TIPWhether you’re a novice or aprofessional, dot matrix on rear glassesare difficult to contend with for installersworldwide. Try the “Dotrix” product forthe most problematic areas.

TOOL TIPApplication of felt tape has become apopular solution to the familiar “scratching”problem on some vehicle roll down windows.

20

SPR

AY

ER

& A

CC

ESSO

RIE

S

SPRAYER & ACCESSORIES

GT090 SPRAYMASTER BOTTLE & TRIGGERAn overall heavy-duty sprayer, thisspray bottle comes with a 5 yearmanufacturers warranty and ischemically resistant. It is equipped witha strong trigger and holds 32 ounces.

GT096 POLYSPRAY 2This pressurized spray bottle holdsmore solution than the 32 oz. bottlesand reduces "finger-fatigue"eliminating the need for pumping whilespraying via a simple trigger. Handy forlarge windows and long durationsprays. Has an adjustable spray nozzle.(1.25 liters)

GT1008 IMPACT JR. PUMP-UP SPRAYERPressurized spray bottle that holds 48ounces and reduces “finger-fatigue”eliminating the need for pumping whilespraying via a simple trigger. Hasadjustable spray nozzle.

GT1067 MERCURY PRO+ BOTTLE & TRIGGERThe next generation in spray bottles,the Mercury PRO+ features viton sealsand a double action pump that spraysboth when you pull back and whenyou release the trigger giving youmore liquid with each pull. Thislightweight ergonomic trigger/bottlecombo holds up to 1 liter (33 ounces) of fluid.

GT097 32OZ. BOTTLEEmpty 32 ounce bottle only.

GT098N MAXI TRIGGER SPRAYERAn industry staple. Ergonomic triggerwith high output and durability.

GT101N 5 GALLON STAINLESSSTEEL SPRAYERDeluxe pressure sprayer holds up to 5gallons of mounting solution in astainless steel tank. Hose can reach upto 25' in length. Fill with solution andpressurize with air from anycompressor. Curly, flexible hosereaches into cars or stretches to goup a ladder with you.

GT101-H REPLACEMENT SPRAY GUNFOR GT101NReplacement nozzle for GT101N.

GT101-HG 25' REPLACEMENT HOSEAND SPRAY GUN FOR GT101NReplacement hose and nozzleassembly for 5 gallon StainlessSteel Sprayer.

GT102 3 GALLON PRESSURE SPRAYERStores either window cleaner orapplication solution. Essential for thosebig commercial jobs. Long 13' hoseallows great mobility and largecapacity gives uninterrupted andfatigue-free installation.

GT2012 NOZZLE FOR PRESSURE SPRAYERReplacement nozzle for the GT102, 3 gallon Pressure Sprayer.

GT102-P REPLACEMENT PUMP FORORANGE 3 GALLON SPRAYER

GT101G 5 GALLON STAINLESSSTEEL SPRAYERThis pressure sprayer has a 15' flex linehose with a brass tip nozzle. The nocurl hose allows for less tension whenmaximizing the reach. A great sprayerfor any type of installation.

GT1038-HG GILMORE NOZZLE &HOSE ASSEMBLY15' flex line hose and Gilmore nozzleassembly for 5 gallon Stainless Steel Sprayer.

GT1038 GILMORE NOZZLEUse with flex line hose. (Does not fit on GT101-HG hose)

GT1008

GT096

GT097

GT102

GT098N

GT101-H

GT101-HG

GT2012 GT102-P

GT1038-HG

GT1038

TOOL TIPAlways clean your tanks and sprayers after48 hours of use to keep contaminationdown. Don’t forget to clean the filters!

TOOL TIPDue to the large amounts of contaminationin tap water, to achieve the best results andthe cleanest installs we highly recommendusing distilled water or a reverse osmosisfiltering system.

NEW

NEW

21

CLEA

NIN

G/P

REP &

CH

EM

ICA

LS

CLEANING/PREP & CHEMICALS

GT070 LOW LINT WIPESCenter Pull Towels, 2 Ply, 8" x 605',660 sheets/roll, 3" core diameter.

GT072 WIPE DISPENSERFor use with GT070.

GT085 WHITE SCRUB PADGT085THK 1" THICK SCRUB PADGreat for cleaning windows prior toinstallation and prepping dot matrixareas.

GT1066 COPPER MESH PADThe Copper Mesh Pad is for dot matrix prep ONLY! It will ABSOLUTELY scratch glass.

GT071 VIRTUALLY “LINT FREE”Reusable wipes. 300' of cloth per box.

GT209 THE SCRUBBERUsed to reach behind speakers andbrake lights. Scrub away adhesivealong the bottom edges of sloped rearwindows. Uses replaceable standardWhite Scrub Pads (GT085) cut 2" x 3".This tool is 3" by 15" long.

GT716 PLEXUS PLASTIC POLISH-13 OZAnti-static plastic polish, safe for all window films. Leaves behind a protective sheen on any plasticsurface.

GT160 FILM GUARD- 19 OZHighly recommended for use after filminstallations as a cleaner and polish.Helps reduce friction and condensationbetween film and rubber gaskets onroll-down windows.

GT715 SPRAYWAY GLASS CLEANER-19 OZAmmonia free, film-friendly aerosolspray used for cleaning film surfacesafter installation. Can also be used asan adhesive remover when left to soak.

GT735 FILM-ON CONCENTRATE1 quart concentrate mounting solution.Use for pressure sensitive adhesivesand sputtered copper films.

GT733 DIRT-OFF CONCENTRATE1 quart concentrate cleaning solution.Use for interior automotive windowcleaning. Great for removing oilydeposits on automotive glass. Dirt-Offcan also be used as an adhesiveaccelerant to give additional tack fordot matrix areas.

GT1071 SUPER STRIPPER ADHESIVEREMOVER- GALLONA highly concentrated, ready-to-useadhesive remover.

GT162P EASY STRIPPER II ADHESIVEREMOVER- GALLONUsed to soften adhesive left on glass.Ready-to-use.

GT070

GT072

GT085GT085THK

TOOL TIPLow lint towels or wipes are a necessity forquality window film installations. Absorbentwipes are ideal for cleaning windows andcovering hard cards for bumping or wickingaround the film edge.

TOOL TIPAfter installing film, be sure to clean and polish it with GT160 Film Guard. FilmGuard is specifically designed for window film and is a great sales add-on.

22

CLEANING/PREP & CHEMICALS CONT’D

CLEA

NIN

G/P

REP &

CH

EM

ICA

LS

GT2013 TINT SLIME- GALLONTint Slime is a window tint mounting & cleaning solution. Tint Slime can beused to install automotive window tint,paint protection film, flat glass film,and vinyl. Tint Slime is free ofparticulates and won’t separate. TintSlime is safe for use on interiors,biodegradable, and of course, tint safe.Concentrate; mix 1 ounce per 1 gallon of water.

GT1036 SIMPLE PINK ADHESIVEREMOVER- GALLONAdhesive remover. Can be used fullstrength or 2-3 parts water.

GT1035 BLUE SLIP UP- GALLONSlip agent to aid in window filminstallation. Mix 8 ounces with 1 gallon water to serve as a conditioner or cleaner.

GT1034 DOT DEVIL- 32 OZA ready-to-use dot matrix prepsolution. Use to aid film adhesion overdot matrix areas in auto installs.

GT2010 TINT OFF- QUARTGT2009 TINT OFF- GALLONReady-to-use and specially formulatedfor the window film industry to maketint removal a snap.

GT714 X-100 APPLICATIONSOLUTION- GALLONCleaning and application concentratefor most dry adhesives. The mild acidformulation makes this a greatcleaning agent for glass contaminatedwith oil, grease or dirt. Recommendedmixture is 1 ounce per 1 quart of water.Not to be used with copper or silverbased films.

GT1040 RAPID REMOVER- GALLONGT1039 RAPID REMOVER- 32 OZA non-toxic, water-soluble adhesiveremover that breaks down andremoves adhesive fast. Ready-to-use.Available in two sizes: Gallon or 32ounce bottles.

GT1041 RAPID TAC II- 30 OZGreat adhesive promoter even in coldweather conditions. A great solutionfor dot matrix areas or vinyl products.

GT2009

GT1040GT1039

TOOL TIPThere are many ways to clean and prepareautomtoive glass, no matter what thecircumstance always test the product ofyour choice in an inconspicuous area toprevent potential damage.

TOOL TIPWhen mixing mounting solutions, itis recommended that you usefiltered water for best results.

TOOL TIPAlways error on the side of caution whenusing chemicals. Be sure to protect yourskin as well as any surfaces the productmay come in contact with.

NEW

GT2010

GT940 FILM HANDLER REPAIR KITGT943 FILM HANDLERREPLACEMENT BLADES20 blades per cartridge.

GT912 FILM HANDLER CUTTER ASSEMBLYThis is the base and the swivel head of the blade holder.

GT986 FILM HANDLERBLADE HOLDERThe swivel head portion of the blade holder.

GT913 6" ROLLER ASSEMBLYUse for security film on 6" cores. Comeswith 12" risers to accommodate rolls offilm on 6” cores. Sold as a pair (2).

GT904 3"ROLLER ASSEMBLYStandard roller assembly on FilmHandler. These are 6" risers and willaccommodate film on 3” cores. Sold as a pair (2).

GT1012 1/4" SHIM FOR 6" HUBSGT1013 1/8" SHIM FOR 6" HUBS

GT941 1/8" SHIM FOR 3" HUBSGT942 1/4" SHIM FOR 3" HUBSSold as eaches (1).

GT910 60" FILM HANDLERGT911 72" FILM HANDLERThe GT910 or GT911 Film Handlercomes standard with 2 each CutterHead Assembly (GT912), 2 each 3"Roller Assembly (GT904) and onepack of blades (GT943). LADDER NOT INCLUDED

GT822 72" BOX SLITTER CHANNEL72" aluminum U-channel for slidingover the edge of a film box to serveas a straight edge when makinghorizontal cuts (across the web width)after pulling film out to desired length.Handy for in-field work. Saves the costof more expensive film cutters. BladeHolder (GT821) sold separately.

GT821 BLADE HOLDER FOR GT822Use any 9mm blade. Blade notincluded.

GT1002 CLEAN CUT BOX SLITTERClean cut is back and better than ever!Available in 36″, 48″, 60″ and 72″ sizes.The new and improved bars are analloy U-channel in a brushed polishedfinish. Each bar has a ruler across thetop edge for precise measuring andplacement of the Cutter Head.

GT1002CH CLEAN CUT CUTTER HEAD ASSEMBLYCutter head assembly for the clean cutbox slitter. The Clean Cut Cutter Headis now machined from composite withtwo neodymium magnets that providetremendous attachment to the Clean Cut Bar.

GT1002B CLEAN CUTREPLACEMENT BLADESA five pack of replacement blades for the Clean Cut Cutter Head(GT1002CH).

GT1002T CLEAN CUT BOX SLITTER TRAYAllows film boxes to be mounted on top of a ladder.

23

SLIT

TER

S &

AC

CESSO

RIE

S

SLITTERS & ACCESSORIES

GT940

GT943GT912

GT986

GT913

GT822

GT904

GT1012GT1013

GT941GT942

GT821

TOOL TIPThe GT910 or GT911 Film Handler willreduce waste, save labor and helpcomplete jobs in a more timely manner.They can also be wall mounted for usein automotive applications.

TOOL TIPTo prevent damage to your FilmHandler cutter head/blade holderalways move the blade holder fromthe base not by the swivel head.

GT2036 TINT-CHEK + TC2800AUTOMOTIVE METERMeasures visible light transmission(VLT) on roll down windows. IncludesALL the benefits of the TC1800(GT2035) plus features a backlit LCDdisplay making it much easier to readin low light conditions. Reads to thenearest tenth percent for greateraccuracy. Calibrated to a NISTtraceable standard.

GT975 STRENGTHENED GLASS DETECTORAllows users to confirm if glass hasbeen strengthened. The detector cantest single panes of glass or multiplepanes in a window at a single time,and from a single side.

GT2064 ENFORCER IIThe TM1000 Enforcer II is a lightweight and pocket sized automotivetint meter. It comes equipped with acoin cell battery that will last for up to2500 uses and is auto calibrating.For rolldown windows only.

GT238 TM2000 INSPECTOR IIThe TM2000 Inspector II is the newestin two piece light meter technologyallowing you to measure ALL windowson vehicles with auto calibrationaccurate to within +/-2%. This meter is 75% smaller than older models and carries a 1 year manufacturer’swarranty.

GT2035 TINT-CHEK TC1800AUTOMOTIVE METERMeasures visible light transmission(VLT) on roll down windows. A smallermeter that fits comfortably into a shirtpocket. Tremendous reliability, ignoringambient light. Calibrated to a NISTtraceable standard.

GT976 GLASS SAMPLE SETConduct your sales demonstrationeffectively by including glass samplesto help illustrate the benefits of filmover standard glass. Includes 2 clearsingle pane, 2 clear IG and 2 low-E sets.

GT961 INSULATED GLASS THICKNESS & GAP GAUGEUsed to measure glass and air spacethickness in sealed insulating glassunits. Carrying case included. Poweredby two standard “AAA” alkalinebatteries (included).

GT962 HEAT LAMP UNITGreat tool for tabletop presentations.Powered by 110 volt power cord. (Plug in).

24

METER

S

METERS

GT978 LASER THERMOMETERReads temperatures of solid surfaces.Demonstrate difference once windowfilm is applied to glass with newreading of solid surface. Not to beused on glass. Powered by a 9-voltalkaline battery (included).

GT2020 HEAT SHEET DEMO CARDVibrantly changes color when itencounters heat. To demonstrate heatblocking capabilities of your glass orfilm, use the Demo Card incombination with a heat lamp.

GT2019 HEAT SHEET ACRYLIC STANDUsed to hold your Heat Sheet DemoCard in place to show heat transfer.

GT963 U.V. LIGHT SOURCE LAMPExcellent tool to demonstrate, measureor show how much U.V. window filmskeep out. Powered by 4 “AA” alkalinebatteries (NOT included).

G T 2 0 2 0 & G T 2 0 1 9S O L D S E PA R AT L E Y

NEW

NEW

GT2020

GT2019

GT969 TOUGHENEDGLASS INDICATORUsed to determine which, if any, panesin a window unit are heat-treated.Knowing this allows use of films thatwould otherwise be inappropriate onregular annealed glass. Full set of user instructions and case included.(120 volt)

GT974-SOFT PROFESSIONAL METERSALES KIT W/CASEOur UV & Solar Sales PresentationKits offer a single source forconvenient and convincing salesdemonstrations. Kit Includes: GT968Digital BTU & Trans-Meter, GT962 HeatLamp Unit, GT973 UV Meter, GT963U.V. Light Source Lamp, GT971 SoftCase with Strap.

GT971 SOFT CASE

GT973 UV SENTRY METERPosition the meter facing the UVsource, such as sunlight or a heat lamp(GT962), and turn the meter on. Placevarious materials between the meterand the UV source and the resultingUV Transmission percentage will bedisplayed. Powered by a 9-volt alkalinebattery (included).

GT967 SP1065 DIGITAL BTU SOLARPOWER METERThis wide spectrum digital metermeasures solar radiant energy intensitydirectly transmitted through glass (orthe film-glass combination) in units ofBTUs per square foot per hour orwatts per square foot. Effective toolshowing the relative effectiveness ofvarious films in blocking solar radiantheat. Especially useful for showinghow a very dark dyed film may allowfar more energy to pass through than a much lighter metallic film. Can beswitched to read in metric units.Powered by a 9-volt alkaline battery(included).

GT968 SP2065 SOLARTRANSMISSION & POWER METERUse this meter to evaluate solarperformance. It provides excellentresolution, reading low light conditionsmore accurately than competitors, withno need for adjustments. The easy toread digital display toggles betweenpower and transmission percentagemode. It's small, portable, andconvenient to take out in the field. Can be switched to read in metricunits. Powered by a 9-volt alkalinebattery (included).

GT960 LOW-E COATING DETECTORDetects the presence and location ofthermal resistant coatings (LOW-E)used on energy efficient single anddual pane glass. Never requirescalibration. Powered by a 9-voltalkaline battery (included).

GT2034 SS2450 SOLAR SPECTRUM TRANSMISSION METERThis device is the most accurate meter to date. It is the onlymeter calibrated to ISO9050, NFRC300 and EN410standards. Effortlessly demonstrate six performancecharacteristics at a time including two IR measurements: UV,VIS, SOLAR, IR 900-1000 nm, and IR 780-1780 nm ensuringthe complete picture of a window film’s performance.Simply slide the glass sample into the opening and see theresulting values displayed. No additional light sources areneeded. Everything is self-contained in a single convenientpackage to visualize the true performance of a glazingsystem, this meter is a must. Glass samples not included.

GT982 SPECTRUM DETECTIVE METERDisplays three ratings at a time: UV, Visible Light, andInfrared transmission values. Carrying case included.Powered by a 9-volt alkaline battery (included).Glass samples not included.

25

METER

S

METERS CONT’D

N OT A L L I T E M SS H OW N A R EI N C L U D E D I N K I T