Flanged Gate Valve, short (F4)- Series 06 and 26

Flanged gate valves are suitable for anyinstallation, as they can be connectedto pipe lines of all materials by meansof AVK combi-flanges or universaladaptors.

• DN 40-300• GGG-50• With internal epoxy (06/30) or internal

enamel (26/00)

Front Page

Products• Water

• Steel pipes

Data SheetsTender Text

Description of series 06/30Gate valve for water

Resilient seated gate valve.Body and bonnet of GGG-50. DN 40 - 300.Flanges and drilling to ISO 7005-2 (EN 1092-2: 1997, DIN 2501), PN 10and PN 16. Short face to face to DIN 3202 part 1, F4.Wedge of ductile iron with fixed wedge nut, fully vulcanized with EPDMrubber.Stem of stainless steel 1.4021 with rolled thread and wedge stop ring.The stem sealing consists of a rubber manchette, 4 O-rings in a nylonbearing and a wiper ring. Bonnet gasket in groove between body andbonnet.Countersunk bonnet bolts encircled by the bonnet gasket and sealedwith hot melt. Epoxy coating to DIN 30677 - internally and externally.Like AVK series 06/30 or approved equivalent.

Front Page

Products• Water

• Steel pipes

Data SheetsTender Text

Description of series 26/00Gate valve for water

Resilient seated gate valve.Body and bonnet of GGG-50. DN 40 - 300.Flanges and drilling to ISO 7005-2 (EN 1092-2: 1997, DIN 2501), PN 10and PN 16. Short face to face to DIN 3202 part 1, F4.Wedge of ductile iron with fixed wedge nut, fully vulcanized with EPDMrubber.Stem of stainless steel 1.4021 with rolled thread and wedge stop ring.The stem sealing consists of a rubber manchette, 4 O-rings in a nylonbearing and a wiper ring. Bonnet gasket in groove between body andbonnet.Countersunk bonnet bolts encircled by the bonnet gasket and sealedwith hot melt. Epoxy coating to DIN 30677 - externally. Enamelled internally.Like AVK series 26/00 or approved equivalent.

Front Page

Products• Water

• Steel pipes

Data SheetsTender Text

For further specification, see section "Technical information". The designs, materials and specifications shown are subject to changewithout notice due to our continuing programme of product development.

AVK INTERNATIONAL A/S/99

AVK GATE VALVE PN 10 OR PN 16 06/X0 - 26/00

To DIN 3352 part 4 / NF E 29-324Face to face dimension to DIN 3202 Part 1, F4Flanges and drilling to ISO 7005-2 (EN 1092-2: 1997, DIN 2501)

Use:

For water, sewage and neutral liquids tomax. 70°C

Tests:

Hydraulic test to DIN 3230 part 4:Seat: PNBody: 1.5 x PN

Operating torque test

Optional extras:

HandwheelExtension spindleStem capFlange adaptor

Approvals:

Series 06/30:ÖVGW - Reg. Nr.: W1.121Series 26/00:DVGW - Reg. Nr.: 81.03 e 397

Materials:

Body and bonnet Series 06/30 and 26/00:Ductile iron, GGG-50, to DIN 1693(BS 2789 grade 500 - 7)Series 06/40:Grey cast iron, GG-25, to DIN 1691(BS 1452 grade 220/250)

Coating Series 06/30 and 06/40:Electrostatically applied epoxy resinto DIN 30677 - Internally and externallySeries 26/00:Electrostatically applied epoxy resinto DIN 30677 - externally. Enamelled internally.

Stem Stainless steel, DIN X 20 Cr 13Stem sealing NBR wiper ring, 2 NBR O-rings

inside and 2 outside a plastic bearing, EPDM rubber manchette

Wedge Ductile iron, GGG-50, core fullyvulcanised with EPDM rubber,with integral wedge nut ofdezincification resistant brass,CZ 132 to BS 2874

Thrust collar Dezincification resistant brass, CZ 132 to BS 2872

Bonnet bolts Stainless steel A2, sealed with hot melt

Bonnet gasket EPDM rubber

Component list

1. Stem2. NBR wiper ring3. NBR O-ring4. Bearing5. Bonnet6. Thrust collar

7. EPDM rubber manchette8. Bonnet bolt9. Bonnet gasket

10. Wedge nut11. Wedge12. Body

Ref. nos. Dh dsGG-25 GGG-50 GGG-50 L H Dt D mm mm Holes F Weight

Internal epoxy Internal epoxy Internal enamel DN mm mm mm mm PN 10 PN 16 PN 10 PN 16 PN 10 PN 16 mm kilos

06-040-30014 26-040-0001 40 140 241 83 150 110 18 4 14 1006-050-30014 26-050-0001 50 150 241 102 165 125 18 4 14 1106-065-30014 26-065-0001 65 170 271 122 185 145 18 4 17 14

06-080-40014 06-080-30014 26-080-0001 80 180 297 138 200 160 18 8 17 1806-100-40014 06-100-30014 26-100-0001 100 190 334 158 220 180 18 8 19 23

06-125-30014 26-125-0001 125 200 376 188 250 210 18 8 19 3106-150-40014 06-150-30014 26-150-0001 150 210 448 212 285 240 22 8 19 4606-200-400X4 06-200-300X4 26-200-000X 200 230 562 268 340 295 295 22 22 8 12 24 65

06-250-300X4 26-250-000X 250 250 664 320 400 350 355 22 26 12 12 27 10206-300-300X4 26-300-000X 300 270 740 370 455 400 410 22 26 12 12 27 149

X: 0= PN 10 1 = PN 16In the sizes DN 250 and DN 300 the upper bolt holes in the flanges are metric threaded (M20 for PN 10 and M24 for PN 16).

AVK GATE VALVE PN 10 OR PN 16 06/X0 - 26/00

To DIN 3352 part 4 / NF E 29-324Face to face dimension to DIN 3202 Part 1, F4Flanges and drilling to ISO 7005-2 (EN 1092-2: 1997, DIN 2501)

1

2

3

4

5

6

7

9

10

11

12

8

L

H

F

ds

DDhDt