Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
34
EC centrifugal fan and modulesbackward curved, Ø 400
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "B"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
1000 2000 3000 4000 5000 6000 7000
0
200
400
0,8
1,6
600 2,4
800 3,2
1000 4,0
1000 2000 40003000
10
11
126
7
8
3
4
159
2
cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
2180
2180
2180
2180
1850
1850
1850
1850
1470
1470
1470
1470
1178
1748
1850
1638
720
1063
1132
1001
361
533
568
502
1,81
2,66
2,90
2,49
1,10
1,62
1,72
1,52
0,55
0,81
0,86
0,76
89
82
81
84
85
78
77
80
80
73
72
75
A
Nominal data
*3G 400 M3G 112-IA
subject to alterations (1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 2180 1850 2,90 -25..+50
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 34
35
6xM10202±1
Ø252±0.5
Ø232±0.3
6x60˚
125182 9
Ø45
5
Ø28
2
Ø13
8
57.5 273±2
330.5±3
68
6xØ9
Ø413
Ø390
Ø270
.9
Depth of screw 12-16 mmR3G 400-AY87 -01
K3G 400-AY87 -02 / -32
R3G 400-AY87 -01 15,6 40075-2-4013
Masse
centrifugalfan
K3G 400-AY87 -02 26,0 K3G 400-AY87 -32 26,0
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: VDE, UL, CSA, CCC, GOST are applied for
(2) Centrifugal module with higher protection against corrosion
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
Centrifugal fan kg Inlet nozzle with onepressure tap
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable glandM20x1,5 (3x):Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm
Tightening torque 3.5±0.5 Nm15327±2
o500-1
o450
Ø11
(4x)
Ø455
384±3o375
M20x1.5
(3x)
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Observe the correctmounting position !Install the support strutsonly vertically as shownin the view !
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 35
36
EC centrifugal fan and modulesbackward curved, Ø 400
Nominal data
*3G 400 M3G 150-FF
subject to alterations
2000 4000 6000 8000
0
200
400
0,8
1,6
600 2,4
800 3,2
1000 4,0
1200 4,8
1400
1000 2000 40003000
10
11
12
6
7
8
3
4
2
159cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
(1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 2550 3000 4,60 -25..+60
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "F"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
2550
2550
2550
2550
2115
2115
2115
2115
1680
1680
1680
1680
1989
2578
3000
2890
1135
1471
1709
1649
569
737
857
826
3,03
3,92
4,60
4,41
1,73
2,24
2,61
2,52
0,87
1,12
1,31
1,26
93
87
85
87
89
83
81
83
84
78
76
78
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 36
37
R3G 400-AQ23 -01 21,7 40075-2-4013
Masse
centrifugalfan
K3G 400-AQ23 -01 32,3 K3G 400-AQ23 -31 32,3
Depth of screw max. 25 mmR3G 400-AQ23 -01
K3G 400-AQ23 -01 / -31
±3
±2
8x45˚
22.5˚
6x60
˚
14xM10
Ø232-2
Ø252±0,3
Ø275
220.5±1
182
125 9
Ø282
Ø455
Ø270
.9
Ø390
Ø413
68
6xØ9265.6
335.670
Ø188
(3x)
M20x1
.5
Ø566
o37515o500-1
Ø11
(4x)
o450
320±2
390±3
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: UL, CSA, GOST
(2) Centrifugal module with higher protection against corrosion
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
Centrifugal fan kg Inlet nozzle with onepressure tap
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable gland M20x1,5 (3x):Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm Tightening torque 3.5±0.5 Nm
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Observe the correctmounting position !Install the support strutsonly vertically as shownin the view !
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 37
38
EC centrifugal fan and modulesbackward curved, Ø 450
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "B"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
2000 4000 6000 8000
0
200
400
0,8
100 0,4
300 1,2
500 2,0
700 2,8
1,6
600 2,4
800 3,2
1000 2000 4000 50003000
10
11
12
6
7
8
3
4
2
159cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
1750
1750
1750
1750
1450
1450
1450
1450
1155
1155
1155
1155
1036
1457
1615
1524
571
812
906
810
306
427
462
411
1,61
2,25
2,50
2,33
0,92
1,28
1,42
1,27
0,56
0,73
0,77
0,70
87
80
77
80
82
75
73
76
76
69
67
69
A
Nominal data
*3G 450 M3G 112-IA
subject to alterations (1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 1750 1615 2,50 -25..+50
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 38
39
6xM10202±1
Ø252±0.5
Ø232±0.3
6x60˚
140204 9
Ø50
5
Ø31
7
Ø13
8
60 295±2
355 ±3
76
6xØ9
Ø480
Ø430
Ø303
.4
Depth of screw 12-16 mmR3G 450-AY86 -01
K3G 450-AY86 -02 / -32
R3G 450-AY86 -01 16,4 45075-2-4013
Masse
centrifugalfan
K3G 450-AY86 -02 31,9 K3G 450-AY86 -32 31,9
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: VDE, UL, CSA, CCC, GOST are applied for
(2) Centrifugal module with higher protection against corrosion
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
Centrifugal fan kg Inlet nozzle with onepressure tap
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable glandM20x1,5 (3x):Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm
Tightening torque 3.5±0.5 Nm15357±2
o630-1
o580
Ø11
(4x)
Ø505
417±3o551
M20x1.5
(3x)
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Observe the correctmounting position !Install the support strutsonly vertically as shownin the view !
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 39
40
EC centrifugal fan and modulesbackward curved, Ø 450
Nominal data
*3G 450 M3G 150-FF
subject to alterations
2000 4000 6000 8000 10000
0
200
400
0,8
1,6
600 2,4
800 3,2
1000 4,0
1200 4,8
1000 2000 4000 5000 60003000
10
11
126
7
8
3
4
2
159cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
(1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 2040 2730 4,20 -25..+60
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "F"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
2040
2040
2040
2040
1695
1695
1695
1695
1345
1345
1345
1345
1773
2500
2730
2587
991
1428
1548
1450
495
713
774
725
2,71
3,80
4,20
3,96
1,52
2,17
2,35
2,22
0,76
1,09
1,18
1,11
92
83
81
83
88
79
77
79
83
74
72
74
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 40
41
R3G 450-AQ24 -01 22,5 45075-2-4013
Masse
centrifugalfan
K3G 450-AQ24 -01 38,2 K3G 450-AQ24 -31 38,2
Depth of screw max. 25 mmR3G 450-AQ24 -01
K3G 450-AQ24 -01 / -31
±3
±2
8x45˚
22.5˚
6x60
˚
14xM10
Ø232-2
Ø252±0,3
Ø275
220.5±1
204
140 9
Ø317
Ø505
Ø303
.4
Ø430
Ø480
76
6xØ9287.2
35770
Ø188
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: UL, CSA, GOST
(2) Centrifugal module with higher protection against corrosion
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
Centrifugal fan kg Inlet nozzle with onepressure tap
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable gland M20x1,5 (3x):Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm Tightening torque 3.5±0.5 Nm
(3x)
M20x1
.5
Ø566
o55115o630-1
Ø11
(8x)
o580
349±2
419±3
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Observe the correctmounting position !Install the support strutsonly vertically as shownin the view !
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 41
42
EC centrifugal fan and modulesbackward curved, Ø 450
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "F"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
2000 4000 6000 8000 10000 12000
0 1000 2000 4000 5000 700060003000
10
11
126
7
8
3
4
2
159
400 1,6
800 3,2
1200 4,8
1600 6,4
2000 8,0
cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
2750
2750
2750
2750
2280
2280
2280
2280
1815
1815
1815
1815
3105
4841
5370
5060
1769
2759
3058
2884
893
1392
1543
1455
4,79
7,47
8,30
7,80
2,73
4,26
4,70
4,44
1,38
2,15
2,37
2,24
100
90
89
93
96
86
85
89
91
81
80
84
A
Nominal data
*3G 450 M3G 150-IF
subject to alterations (1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 2750 5370 8,30 -25..+40
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 42
43
406.5±3
113 293.5±2
112176
Ø188
Ø317
Ø505
9
Ø280-2
Ø304±0.5
6x60˚
6xM10
766xØ9
Ø303
.4
Ø430
Ø480
Depth of screw max. 20 mm
o520.5o630-1
o580
Ø11(8x)
469±3355.5 ±2 15
R3G 450-AZ30 -01
K3G 450-AZ30 -01 / -31
R3G 450-AZ30 -01
kg
31,1
Inlet nozzle with onepressure tap
45075-1-4013
Masse
centrifugalfan
Centrifugal fan
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: UL, CSA, GOST
K3G 450-AZ30 -01 52,7 K3G 450-AZ30 -31 52,7
(2) Centrifugal module with higher protection against corrosion
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable gland M25x1,5(1x)
Cable gland M20x1,5(2x)
Cable diametermin. 9 mm, max. 16 mm,tightening torque 6±0.9 Nm
Tightening torque3.5±0.5 Nm
Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 43
44
EC centrifugal fan and modulesbackward curved, Ø 500
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "F"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
2000 4000 6000 8000 10000 12000
0
200
400
0,8
1,6
600 2,4
800 3,2
1000 4,0
1000 2000 40003000 5000 70006000
10
11
12
6
7
8
3
4
2
159cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
A
Nominal data
*3G 500 M3G 150-FF
subject to alterations (1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 1780 2825 4,30 -25..+60
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
1780
1780
1780
1780
1475
1475
1475
1475
1175
1175
1175
1175
1985
2530
2825
2692
1094
1411
1602
1484
553
714
810
750
3,09
3,90
4,30
4,14
1,70
2,18
2,47
2,28
0,86
1,10
1,25
1,15
94
89
83
85
90
84
79
80
85
80
74
75
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:33 Seite 44
45
Depth of screw max. 25 mmR3G 500-AP25 -01
K3G 500-AP25 -01 / -31
8x45˚
22.5˚
6x60
˚
14xM10
Ø232-2
Ø252±0,3
Ø275
220.5±1
220
150 12
Ø352
.5
Ø566
Ø337
.2
Ø445
Ø470
75
6xØ9303.5
373.570
Ø188
±3
±2
R3G 500-AP25 -01 24,6 64025-2-4013
Masse
centrifugalfan
K3G 500-AP25 -01 40,2 K3G 500-AP25 -31 40,2
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: UL, CSA, GOST
(2) Centrifugal module with higher protection against corrosion
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
Centrifugal fan kg Inlet nozzle with onepressure tap
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable gland M20x1,5 (3x):Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm Tightening torque 3.5±0.5 Nm
(3x)
M20x1
.5
Ø566
o55115o630-1
Ø11
(8x)
o580
361.5±2
431.5±3
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Observe the correctmounting position !Install the support strutsonly vertically as shownin the view !
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:34 Seite 45
46
EC centrifugal fan and modulesbackward curved, Ø 500
Nominal data
*3G 500 M3G 150-IF
subject to alterations
2000 4000 6000 8000 10000 12000 14000
0
200
400
0,8
1,6
600 2,4
800 3,2
1000 4,0
1200 4,8
1400 5,6
1600 6,4
2000 4000 80006000
10
11
12
6
7
8
3
4
2
159cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
(1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 2200 5500 8,40 -25..+45
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "F"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
2200
2200
2200
2200
1825
1825
1825
1825
1465
1465
1465
1465
3725
4944
5500
5148
2039
2736
3052
2830
1055
1416
1578
1464
5,82
7,64
8,40
7,95
3,19
4,23
4,70
4,37
1,65
2,19
2,43
2,26
100
94
89
90
95
90
84
86
91
85
80
81
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:34 Seite 46
47
R3G 500-AQ33 -01 33,2 64025-2-4013
Masse
centrifugalfan
K3G 500-AQ33 -01 55,9 K3G 500-AQ33 -31 55,9
450.5±3
113 337.5±2
298.5±1
150220.5
Ø188
Ø352
.5Ø5
66
12
Ø280-2
Ø304±0.5
6x60˚
6xM10
756xØ9
Ø337
Ø445
Ø470
Depth of screw max. 20 mm
Cable gland M25x1,5(1x)
R3G 500-AQ33 -01
K3G 500-AQ33 -01 / -31
(2) Centrifugal module with higher protection against corrosion
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: UL, CSA, GOST
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
Centrifugal fan kg Inlet nozzle with onepressure tap
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable gland M20x1,5(2x)
Cable diametermin. 9 mm, max. 16 mm,tightening torque 6±0.9 Nm
Tightening torque3.5±0.5 Nm
Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm
o520.5o630-1
o580
Ø11(8x)
510±3396.5 ±2 15
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:34 Seite 47
48
EC centrifugal fan and modulesbackward curved, Ø 560
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "F"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
2000 4000 6000 8000 10000 12000 14000
0
200
400
0,8
1,6
600 2,4
800 3,2
1000 4,0
2000 4000 80006000
10
11
12
6
7
8
3
4
2
159cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
1500
1500
1500
1500
1250
1250
1250
1250
1000
1000
1000
1000
1952
2481
3000
2754
1101
1420
1712
1560
564
727
876
799
2,98
3,77
4,60
4,18
1,68
2,16
2,60
2,37
0,86
1,10
1,33
1,21
90
86
80
83
86
82
76
78
81
77
71
74
A
Nominal data
*3G 560 M3G 150-IF
subject to alterations (1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 1500 3000 4,60 -25..+50
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:34 Seite 48
49
Depth of screw max. 25 mmR3G 560-AP23 -01
K3G 560-AP23 -01 / -31
8x45˚
22.5˚
6x60
˚
14xM10
Ø232-2
Ø252±0,3
Ø275
250.5±1
±3
±2
239
160 16
Ø395
Ø636
Ø385
Ø490
Ø515
82
6xØ9352
42270
Ø188
R3G 560-AP23 -01 30,5 64030-2-4013
Masse
centrifugalfan
K3G 560-AP23 -01 56,1 K3G 560-AP23 -31 56,1
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: UL, CSA, GOST
(2) Centrifugal module with higher protection against corrosion
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
Centrifugal fan kg Inlet nozzle with onepressure tap
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable gland M20x1,5 (3x):Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm Tightening torque 3.5±0.5 Nm
(3x)
M20x1
.5
Ø566
o55515o800-1
Ø11
(8x)
o750
413±2
483±3
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Observe the correctmounting position !Install the support strutsonly vertically as shownin the view !
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:34 Seite 49
50
EC centrifugal fan and modulesbackward curved, Ø 560
Nominal data
*3G 560 M3G 150-NA
subject to alterations
4000 8000 12000 16000
0
200
400
0,8
1,6
600 2,4
800 3,2
1000 4,0
1200 4,8
1400
2000 4000 6000 8000
10
11
12
6
7
8
3
4
2
159cfm
qV
p sf
Pa
inH 2
O
m3/h
Curves
(1) Nominal data in operating point with maximum load and 400 VAC
3~ 380-480 50/60 1750 4700 7,30 -25..+40
Curve
Nominal
voltage
range
Frequency
Speed/rpm
(1)
Perm.amb.temp.
L5)
Electr.connection
A
– Material: Support bracket: Steel, coated in blackSupport plate: Sheet steel, hot-galvanisedImpeller: Sheet aluminium, weldedRotor: Coated in blackElectronics enclosure: Die-cast aluminium
– Number of blades: 7– Direction of rotation: Clockwise, seen on rotor– Type of protection: IP 54 (acc. to EN 60529)– Insulation class: "F"– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request– Condensate discharges: Rotor-side– Mode of operation: Continuous operation (S1)– Bearings: Maintenance-free ball bearings
1
2
3
4
5
6
7
8
9
10
11
12
A
A
A
A
A
A
A
A
A
A
A
A
1750
1750
1750
1750
1450
1450
1450
1450
1150
1150
1150
1150
3032
3929
4700
4366
1675
2171
2602
2432
836
1083
1298
1213
4,77
6,10
7,30
6,71
2,64
3,37
4,01
3,74
1,32
1,68
2,00
1,87
97
91
84
86
93
87
80
82
88
82
75
76
A
nrpm
PeW
Max.
inputpow
er(1)
Max.
currentdraw(1)
IA
LWAdB(A)
Type Motor VAC Hz rpm W A °C p. 64
Air performance measured
as per: ISO 5801,
Installation category A,
with ebm-papst inlet nozzle
without protection against
accidental contact
Suction-side noise levels:
LWA as per ISO 13347,
LpA measured at 1 m distance
to fan axis
The acoustic values given are
only valid under the measur-
ment conditions listed and
may vary depending on the
installation situation.
With any deviation to the stan-
dard setup, the specific values
have to be checked and re-
viewed once installed or fitted!
For detailed information
see page 66 ff.
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:34 Seite 50
51
R3G 560-AQ04 -01 40,0 64030-2-4013
Masse
centrifugalfan
K3G 560-AQ04 -01 69,7 K3G 560-AQ04 -31 69,7
505±3
113 392±2
333±1
160239
Ø188
Ø395
Ø636
16
Ø280-2
Ø304±0.5
6x60˚
6xM10
826xØ9
Ø385
Ø490
Ø515
Depth of screw max. 20 mmR3G 560-AQ04 -01
K3G 560-AQ04 -01 / -31
(2) Centrifugal module with higher protection against corrosion
– Technical features: • Slave output 0-10 V max. 3 mA • Line undervoltage / phase failure detection• PFC (passive) • Output 20 VDC (±20 %) max. 50 mA • Over-temperature protected electronics / motor• Integrated PID controller • Output 10 VDC (+10 %) max. 10 mA • Locked-rotor protection, Soft start• Control input 0-10 VDC bzw. 4-20 mA • RS485 MODBUS • Digital inputs for day/night switch,• Input for sensor 0-10 V or 4-20 mA • Motor current limitation, Alarm relay enabling, cooling / heating
– EMC: Interference emission acc. to EN 61000-6-3Interference immunity acc. to EN 61000-6-2Harmonics acc. to EN 61000-3-2/3
– Leakage current: < 3,5 mA acc. to EN 61800-5-1– Connection leads: Via terminal strip– Protection class: I (acc. to EN 61800-5-1)– Product conforming to standards: CE– Approvals: UL, CSA, GOST
Inlet nozzlep. 60
Guard grillep. 60
Electr. connectionp. 64
Centrifugal fan kg Inlet nozzle with onepressure tap
Centrifugal modulew. support bracket kg Centrifugal module
w. supp. bracket (2) kg
Cable gland M25x1,5(1x)
Cable gland M20x1,5(2x)
Cable diametermin. 9 mm, max. 16 mm,tightening torque 6±0.9 Nm
Tightening torque3.5±0.5 Nm
Cable diametermin. 4 mm, max. 10 mm,tightening torque 4±0.6 Nm
o570o800-1
o750
Ø11(8x)
566±3453 ±2 15
Pressure tap
Massofcentrifugal
modulewith
support
bracket
Massofcentrifugal
modulewith
support
bracket
Plug_Fans_19_05_2011_EN_:G1G_170_deutsch_.qxd 19.05.2011 11:34 Seite 51