Embed Size (px)
Citation preview
If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com© 2015 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.
Printed in U.S.A.
®
Page 1 of 4003876D Rev N
5/32"HEX DRIVE
#2 PhillipsScrewdriver
Power Drill
11/32" Dia. Drill Bit
5/16 & 1/2 Wrench
FYI® Single & Dual Flat Panel Monitor Arm
Slatwall/SlatRailBracketFPASWR
Wall MountBracketFPAWALL
Desk Clamp/ GrommetBracket(Service Part)
Through MountBracket(Service Part)
FYI Single Monitor Arm with Frame One BracketFPASINGLEFO
1/16", 5/32", 3/16" & 1/4"Allen Wrench
on architectural walland freestanding stanchions
NOTE: Located in MonitorArm Hardware Pack.
Slatwall/SlatRailWall Mount
1
1
2
4
3 2
Attach assembly to wall with (4)fasteners (not included) appropriateto the construction of the wall.
Use #10 woodscrews whenattaching to astud.
Use #10 togglebolts whenattaching directlyto drywall.
Desk Clamp / Grommet Through Mount
1 1
2
2
3
3
4
Drill 11/32" hole
4
5
(Service Part) (Service Part)
Service Part Instruction
DFPASINGLECS
FYI Single Flat Panel Monitor Arm with c:scape Bracket
DFPADUALCS
FYI Dual Flat Panel Monitor Arm with c:scape Bracket
Page 2 of 4003876D Rev N
®
DFPADUALCS
FYI Dual Flat Panel Monitor Arm with c:scape Bracket
1b
2
CLAMPINGBRACKET
BRACE
BASEBRACKET
1c
1a
FOR DUAL MONITOR ASSEMBLY ONLY - Guide brace into place, beneath worksurface. Install two (2) but do not tighten yet.
T-NUT
RAIL
SCREW
Side View
4
3
5
6
7
7
Attach FYI arm to receiver with screw/washers (included with FYI arm).
Attach FYI arm/receiver assembly to base bracket with included hardware (qty 2).
Tighten screws from step 1.
Tighten screws from step 2.
Install plastic cover by sliding it over the top of the base bracket.
PLASTIC COVER
BASE BRACKET
3
WASHER
LOCK WASHER
RECEIVER
FYI ARM
CAP SCREW
4FYI ARM/RECEIVER
ASSEMBLY4FYI ARM/RECEIVER
ASSEMBLY
DFPASINGLECS
FYI Single Flat Panel Monitor Arm with c:scape Bracket
1
2
Mount screws and t-nuts in the correct orientation as shown (1a). Slide clamping bracket into bottom of base bracket (note tab direction per side view(1b) and lower onto rail at rear of c:scape desk (1c).Align two (2) t-nuts with rail slot to aid installation.Do not tighten screws yet.
FOR SINGLE MONITOR ASSEMBLY ONLY - Install two (2) screws but do not tighten yet.
Note:Install (2) screws, but omit the brace, when attaching to the Campfire Big Table with center rail and trough.
Single Dual
)
Page 3 of 4003876D Rev N
®
Insert screws into bottom of monitor arm. Allow two (2) fasteners to protrude approx. 1/4". These will be fully tightened after Step 2.
Slip bracket over screw heads (from Step 1) using the keyhole slots. Slide brackets together and tighten two (2) screws.
Guide two (2) flat head screws through bracket and partially thread T-nuts onto screws. Note proper orientation of T-nuts.
Place arm/bracket assembly onto desk rail. Tighten two (2) flat head screws and T-nuts from Step 3.
Install locking plate onto face of assembled bracket. Install and tighten final screw.
1
2
1
2
3
4
5
Install upper arm as shown.6
Install VESA monitor plate as shown.7
See notebelow
Some models willrequire this screwto be installed bythe end user.
Frame OneRail
Assembled and In position on Frame One Rail
SIDE VIEW
5
3
3
4
6
7
FYI Single Monitor Arm with Frame One BracketFPASINGLEFO
NOTE: Located in MonitorArm Hardware Pack.
Page 4 of 4003876D Rev N
®
FYI Single Monitor Arm with Frame One BracketFPASINGLEFO
SET SCREW
T-HANDLE
18
7
While adjusting the T-handle, the upper arm should be nearly horizontal, to allow the T-handle to turn freely.
If resistance is encountered, raise or lower upper arm,until the T-handle begins to turn easily.
10• If monitor sinks when installed, pull up theT-handle and turn clockwise until monitor"floats".
• If monitor rises when installed, pull up theT-handle and turn counter-clockwise untilmonitor "floats".
Attach VESA Bracket to backside of monitor.
Slide monitor mount assembly onto end of arm until audible "click" is heard. Tighten set screw to prevent removal of monitor.
Gently pry off cable cover on the bottom of the arm. Insert cables into arm cavity and through two loops underthe arm. Press cover back into place.
Adjust T-handle to accommodate weight of monitor. The monitor should "float" (neither rise nor fall) when the counterbalance is properly adjusted.
DFPADUALCS
FYI Dual Flat PanelMonitor Arm with c:scape Bracket
Slatwall/SlatRailBracketFPASWR
Wall MountBracketFPAWALL
Through MountBracket
Desk Clamp / GrommetBracket(Service Part)
(Service Part)
7
8
10
insert cables
cable cover
9
9
DFPASINGLECS
FYI Single Flat Panel Monitor Arm with c:scape Bracket
RELEASEMECHANISM
