Upload
sueidah-abakar
View
2
Download
0
Embed Size (px)
Citation preview
A Course of Study (CoS) is a component of the Training Manual (TM) used by
Accredited Training Centers (ATC) of Department of Skills Development (DSD) when
implementing their training programs. It is the bridge that links the expected
performance objectives to a specified training program. It is intended to ensure the
implementation of Malaysia Skills Certification System will be standardized among
training providers to meet the National Occupational Skills Standard (NOSS)
requirement.
The CoS developed will be used by trainers or module developers in developing their
instructional materials or in DSD context is the Written Instructional Materials (WIM).
CoS provides directions to module developers to meet the desired performance
objectives.
The CoS shall contain essential information on the objectives, and expected
performance objectives. It will be used by module developers as a base on which to
build units of instructions, classroom lessons, practical activities, and different level of
assessments.
The CoS shall also be prepared in the standard format and layout specified in this
document.
COURSE OF STUDY
C-051-2JUNIOR ELECTRICAL TENCHNICIAN
SMK BANDAR EASTER, KOTA TINGGI, JOHOR
EN DAUB BIN HASHIM 671014-01-5201EN NOOR AZIL BIN MOHD SALLEH 821129-01-5093
SMK TENGKU IDRIS SHAH KAPAR, KLANG SELANGOR
PN NOR JANAH BT KASTAMAN 820917-01-6586 PN SUHAIDAH BT ABU BAKAR 850824-04-5238
DEVELOPMENT COMMITTEE
HJ ZAKARIA BIN MD NOORTIMBALAN PENGARAH
PEMBANGUNAN KEJURULATIHAN PTVBAHAGIAN PENDIDIKAN TEKNIK & VOKASIONAL (BPTV)
KEMENTERIAN PENDIDIKAN MALAYSIA
EN. MOHD NOH BIN AHMADKETUA PENOLONG PENGARAH
PEMBANGUNAN KEJURULATIHAN PTVBAHAGIAN PENDIDIKAN TEKNIK & VOKASIONAL (BPTV)
KEMENTERIAN PENDIDIKAN MALAYSIA
EN. MAZLAN BIN MOHDPENOLONG PENGARAH
PEMBANGUNAN KEJURULATIHAN PTVBAHAGIAN PENDIDIKAN TEKNIK & VOKASIONAL (BPTV)
KEMENTERIAN PENDIDIKAN MALAYSIA
FACILITATOR
BPTVSERI ZAIDAH BINTI ZAINI
CIASTEN SHAHABUDIN BIN MD NOR
EN ABDUL RAHMAN BIN ABDULLAH
INTRODUCTION
This manual will serve as a guide to subject matter experts or curriculum specialists who is responsible for the development of the Course of Study for a specified program under the Department of Skills Development (DSD), Ministry of Human Resource Malaysia.
This manual will provide curriculum specialists a general yet comprehensive guideline and expected components, format and layout of a Course of Study Package.
The National Occupational Skills Standards (NOSS) developed by the DSD will be used as the basis for developing the syllabus or content of the Course of Study.
This manual together with the NOSS will be the main official reference to be used in the development of a Course of Study by curriculum specialists; so that the Course of Study developed will follow the general guidelines and standards expected by the DSD, being the authority of the Malaysia’s national skills programs.
PURPOSE / USAGE
A CoS Package will provide module developers or trainers with a guide and direction when preparing training materials or Written Instructional Materials (WIM) for a particular program.
i. The CoS Package will contain information pertaining the job performance and competency requirements of a particular skill.
ii. The CoS Package will contain information on the training programs to be conducted and the sequence of the learning, for a learner to achieve the skill competency required.
iii. The CoS Package will contain a set of CoS which provides a comprehensive description on the knowledge to be delivered for each training module.
iv. Each individual CoS will contain information pertaining to the mode and scope of coverage of knowledge to be delivered and the tasks to be performed.
v. The CoS will assist trainers in course planning, training implementation, evaluation and monitoring the effectiveness of course delivery.
vi. The CoS will provide guidelines to carry out assessment for understanding of knowledge delivered.
vii. The CoS will provide guidelines to conduct assessment to determine competency achievement expected of trainees.
OCCUPATION: ELECTRICAL TECHNICIANMODULE 07 MODULE PERFORM TROUBLESHOOTING
Sub task/step ENABLING REQUIREMENT(Knowledge, Skill, Attitude,& Safety)
TOOLS, EQUIPMENT & MATERIALS
1. Obtain Blueprint Schematic diagram
2. Identify Breakdown
3. Follow repair procedure
Knowledge of:1.1 Blueprint/schematic diagram
Ability to: 1.1 read and interpret blueprint/schematic
diagram
Attitude/safety:
Knowledge of: 2.1 Type of fault2.2 Routine maintenance schedule
Ability to:2.1 Determine type of fault2.2 Determine location2.3 Follow maintenance schedule
Attitude/safety: Safety consciousnessHousekeeping
Knowledge of:3.1 Faults repair procedure3.2 spare parts list 3.3Maintenance procedure3.4 Type of Maintenance tools / equipments3.5 Type of parts to be replaced3.6 Type of electrodes
Ability to:3.1 Repair faults3.2 Replace breakdown part3.3 Carry Out maintenance3.4 Prepare Check List3.5 Comply Maintenance Procedure shutdown3.6 Select tools & equipment
- Blueprint schematic Diagram
- Tools kit- Testing instrument- Safety Sign Board- Log Book- Ladder - Cotton waste- Cleaning material
4. Testing and commissioning
3.7 Determine Parts to be replaced
Attitude/ safety:Wear PPEDisplay safety sign-boardUsing proper tools & equipmentHousekeeping
Knowledge of: 4.1 Testing commissioning procedure4.2 Testing tools and equipment4.3 Testing commissioning check list
Ability to:4.1 Perform function testing4.2 Used testing equipment/tools4.3 Procedure test and commissioning report
Attitude/safety:Wear PPEUsed testing equipments/tools