Upload
khaan1830
View
69
Download
14
Embed Size (px)
DESCRIPTION
Full Body Harness
Citation preview
Fall Protection
INSPECTION AND USE OF
FULL BODY HARNESS &
LANYARD
“Taking Fall Protection Awareness to New
Heights”
Fall Protection
• Falls are the leading cause of fatalities in the construction industry.
• An average of over 300 fatal falls occurred over the last 5 years.
Fall Protection
Other, 39%
Roofs, 26%Scaffolds,
19%
Floors, 10%Ladders,
6%
OSHA Fall Fatality StudyOSHA Fall Fatality Study
Fall Protection
DefinitionsDefinitions• Full-Body Harness: straps which will
distribute the fall arrest forces over at least the thighs, pelvis, waist, chest and shoulders with means for attaching it to other components of a personal fall arrest system.
Fall Protection
• Lanyard: a flexible line of rope, wire rope, or strap which generally has a connector at each end for connecting the body-harness to a deceleration device, lifeline, or anchorage point.
DefinitionsDefinitions
Fall Protection• Deceleration Distance: the additional vertical distance a
falling employee travels, excluding lifeline elongation and free fall distance, before stopping. From the point at which the deceleration device engages, the fall should travel no more than 3.5 Feet (1m)
• Shock-absorber deceleration device … designed to dissipate energy and limit deceleration forces.
• Always connect shock-absorber closest to body.
Fall ProtectionEquipment : Shock Absorbing Lanyard
• When using a 1.8m (6 ft) shock absorbing lanyard, add to that the max stretch of the lanyard 1.1m (3½ ft) & the height of the worker 1.8m (6 ft)
• Then add a safety factor, say 0.9m (3 ft)
• The total of 5.6 m (18½ ft) is the safe height at which to anchor a lanyard to avoid contact with the level below
1.8m
1.1m
1.8m
0.9m
5.6m
Fall Protection
VIDEO PRESENTATION
Fall ProtectionHow to put on a Harness - Step 1
• Hold harness by back D-ring
• Shake harness to allow straps to fall into place
• Identify where is the front and back
Fall ProtectionHow to put on a Harness - Step 2
• If chest, leg and/or waist straps are buckled, release them and unbuckle at this time
Fall ProtectionHow to put on a Harness - Step 3
• Slip straps over shoulders so D-ring is located in middle of back between shoulder blades
Fall ProtectionHow to put on a Harness - Step 4
• Pull leg strap between legs and connect to opposite end
• Repeat with second leg strap
Fall ProtectionHow to put on a Harness - Step 5
• Connect chest strap and position in mid-chest area
• Tighten to keep shoulder straps tight
Fall ProtectionHow to put on a Harness – Step 6
• After all straps have been buckled, tighten all buckles so that harness fits snug but allows full range of movement
• Pass excess strap through loop keepers
Fall ProtectionSafety Harness & lanyard Inspection Checklists
Fluor Form 000.653.F0161Equipment Inspection Date:
Equipment Identification / Registration Number: Full Body Harness I.D. No. \ Lanyard I.D. No
Month/Year Equipment Introduction to Service: Full Body Harness : Month Year \ Lanyard : Month Year
Equipment Manufacturer:
COMPONENT INSPECTED
KEY: P = Pass F = Fail Place tick ( or ) in relevant column as per Guidelines in Practice 000.653.8105
Harness Webbing or
Leather
All Stitching Sewing
Snap HooksSafetyLatch
Engineered Anchor Points
D-Ring's)Buckles) Adjusters)
Include Tongue
Rivets and
Eyelets
RopesChainsLanyardLifelines
Body Pad (If Applicable) Inspected By
P F P F P F P F P F P F P F P F Name Signature
Fall Protection
Frayed webbing
Stitching pulled apart
Harness & Lanyard Web Inspection
Fall Protection
• In excessive heat, nylon becomes brittle & has a shrivelled brownish look
• Fibers will break when flexed
• Should not be used above 180° F (82° C)
How to see Damage to Webbing due to : HEAT
Harness & Lanyard Web Inspection
Fall Protection
• Webbing strands fuse together
• Hard shiny spots
• Hard and brittle to the touch How to see Damage to Webbing
due to : MOLTEN METAL OR FLAME
Harness & Lanyard Web Inspection
Fall Protection
• Small cut in lanyard– 1 mm cut can result
in a 5% to 39% loss of strength
• Lanyards need to be inspected very carefully…
How to see Damage to Webbing due to :
CUTS
Harness & Lanyard Web Inspection
Fall Protection
Hook Nose
GateLock
Hinge
Hook Body
Eye
Release
• "Snaphook" means a connector comprised of a hook-shaped member with a normally closed keeper, which may be opened to permit the hook to receive an object and, when released, automatically closes to retain the object.
Fall ProtectionAnchorage• Anchorage: a secure point of attachment for
lifelines, lanyards or deceleration devices.• Anchorages used for attachment of
personal fall arrest equipment shall be independent of any anchorage being used to support or suspend platforms and capable of supporting at least 5,000 pounds (22.2 kN). per employee attached.
• As part of a complete personal fall arrest system which maintains a safety factor of at least two … under the supervision of a qualified person.
Fall Protection
• Buckle or D-ring sewn into a body-belt or body harness.
Fall Protection
Eyelets
Rivets
Fall Protection
Lifeline
Lanyards
Fall Protection
• Use same inspection methods as for full body harnesses
• Look for the warning flag or signs of deployment
• If flag has been activated, remove the shock-absorbing lanyard from service
Fall Protection
Equipment : Fall Limiter
• Limits the distance you can fall
• Very light and compact only 1.1kg (2.5 lbs)
• Comes complete with a cross arm strap