Fuji PLC Conection 1

8/12/2019 Fuji PLC Conection 1

1/13

Device/PLC Connection

Abou t the Devic e/PLC Connect ion Manuals

Prior to reading these manuals and setting up your device, be sure to read the"Important: Prior to reading the Device/PLC Connection manual" information. Also,be sure to download the "Preface for Trademark Rights, List of Units Supported, Howto Read Manuals and Documentation Conventions" PDF file. Furthermore, be sureto keep all manual-related data in a safe, easy-to-find location.

Manuals


2/13

Chapter 2 - PLC-GP Connection

2-3-1

2.3 Fuji Electric

GP-PRO/PBIII for Windows Device/PLC Connection Manual

CPU Link I/F Cable Diagram Cables GP

PC

I/F Module/Generic I/F

F80H, F120H,F250

FFU-120BPC Interface Module

RS-232C(Cable Diagram 1)

RS-422(Cable Diagram 2)

RS-232CDigital's GP410-IS00-O (5m)

F70S (NC1P-S0) NC1L-RS2 (Generic

Interface)*1


Digital's GP410-IS00-O (5m)

GP Series

2.3 Fuji Electric

2.3.1 System Structure

R e f e r e n c e

The following describes the system structure for connecting the GP to FujiElectric Corporation, Ltd. PLCs.

Cable Diagrams mentioned in the following tables are listed in the section titled " 2.3.2 Cable Diagrams ".

In the LS area, 32-bit devic es are not s upp orted . Therefore, wh en System A rea address es are allocated to B D, DL, or W33 devices,only System Area (LS0 to LS19) address es can be used . Other LS areas, such as the user area, etc. sho uld n ot be us ed.

MICREX-F Series (using Link I/F)

!!!!!Important

*1 When expansion units are attached via a T-Link system to a main PLC unit,

and more than 2 link units are attached to the expansion unit, the GP unit canbe attached to only one of the link units. (Simultaneous connection to 2 link units is not possible.)

Simultaneous connection to 2 link units is possible only when they are at-tached to the main PLC unit.


3/13


2-3-2

2.3 Fuji Electric



GeneralSIO Unit/

GeneralI/F Module

NB1, NB2, NB3 NB-RS1-AC(Generic RS-232C/485 SIO unit)


RS-422

(Cable Diagram 2)


NJ-RS2 (Generic RS-232C SIO interfacemodule)


Digital's GP410-IS00-O (5m)

NJ-RS2 (Generic RS-485 SIO interfacemodule)


NS NS-RS1 (Generic RS-232C/485 interfacemodule)


RS-422

(Cable Diagram 2)


NJ

GP Series

CPU Adapter Cable Diagram Cables GPPC Loader adapter

F80H, F250,F120H

Fuji Electric's FLT-ASFK RS-232C(Cable Diagram 1)

RS-232CDigital's GP410-IS00-O

GP Series

Note:Note:Note:Note:Note: Places noted as RS-422 can also use RS-485 on the PLC side.

MICREX-F Series (FLT-ASFK) (CPU Direct Connection)

FLEX-PC Series (using Link I/F)


PC

InterfaceModule

FFK120A-C10 RS-232C(Cable Diagram 1)



FFK100A-C10 RS-232C(Cable Diagram 3)

GP Series

F80H, F120H,F250F30, F50, F60,F80, F81, F120F120S, F200

MICREX-F Series (using Link I/F)


4/13


2-3-3

2.3 Fuji Electric


CPU Cable Diagram GP

NB1, NB2, NB3, NJ,NS


GP Series

FLEX-PC Series (CPU Direct Connection)

When using Digital's T-Link I/F Unit, refer to the GP-*50/70 Series T-Link I/FUnit User's Manual.

Note:Note:Note:Note:Note:


5/13


2-3-4

2.3 Fuji Electric


2.3.2 Cable Diagrams

!!!!!Important

Ca r e f u l!

Ca r e f u l !

The cable diagrams illustrated below and the cable diagrams recommended by Fuji Electric Co., Ltd. may differ; in any case, using these cables for your PLC operations will not cause any problems.

Ground your PLC's FG terminal according to your country's appli-cable standard. For details, refer to the corresponding PLC manual.

Conn ect the FG line of the Shield cable to either the GP or PLC,depending on your environment . When using a connector hood

and grou nding the FG l ine, be sure to use an electr ical condu c- tor.

For the RS-232C conn ection, use a cable length less th an 15m.

If a comm unicat ions cable is used, i t must be conn ected to the SG (signal ground ).

Cable Diagram 1 (RS-232C)

When using Digital's RS-422 connector terminal adapter GP070-CN10-0

Turn on the Termination Resistor switch, on the PLC side.

Cable Diagram 2 (RS-422)

NC


6/13


2-3-5

2.3 Fuji Electric



When using Digital's RS-422 Cable, GP230-IS11-0

When making your own cable connections

When making your own cable connections, we recommend using HitachiDensen's CO-SPEV-SB(A)3P*0.5S cable.

When connecting the #9 and #10 pins in the GP Serial I/F, a termination resis-tance of 100 is added between RDA and RDB.

Cable Diagram 3 (RS-232C)

A4 ER A6 CIB1 FGB2 SDB3 RDB4 RSB5 CS

B6 DRB7 SGB8 CD

PLC

RDA

RDB

SDA

SDB

SDA

SDB

RDA

RDB

S

NC

CD


7/13


2-3-6

2.3 Fuji Electric



Cable Diagram 4 (RS-422)

For the PLC side connector (modular-jack) you can use Hirose's TM11P-88P.

The pin numbers of the modular-jack for the connec-tion diagrams below are based on the order describedin the figure at the left.

When using Digital's RS-422 connector terminal adapter GP070-CN10-0

When using Digital's RS-422 Cable, GP230-IS11-0

When making your own cable connections

When connecting the #9 and #10 pins in the GP Serial I/F, a termination resis-tance of 100 is added between RDA and RDB.Note:Note:Note:Note:Note:


8/13


2-3-7

2.3 Fuji Electric


2.3.3 Supported Devices

Setup System Area here.

(See next page)

The following describes the range of devices supported by the GP.

MICREX-F Series

* 1 The MSB (most significant bit) of a word device corresponds to bit 0 of the device,and the LSB (least significant bit) corresponds to bit F .

E.g. When hexadecimal data 0001 is written to a Word device address

Device Bit Address Word Address

I/O Relay B0000 ~ B511F WB0000 ~ WB0511 *1

Direct I/O --- W24.0000 ~ W24.0159

Auxilary Relay M0000 ~ M511F WM0000 ~ WM0511 *1

Keep Relay K0000 ~ K063F WK000 ~ WK063 *1

Differential Relay D0000 ~ D063F WD000 ~ WD063 *1 *4

Link Relay L0000 ~ L511F WL000 ~ WL0511 *1

Special Relay F00000 ~ F4095F WF0000 ~ WF4095 *1 *4

Announce Relay A00000 ~ A4095F WA0000 ~ WA4095 *1 *4

Timer 0.01 sec T0000 ~ T0511 ---

Timer 0.1 sec T0512 ~ T1023 ---

Counter C0000 ~ C0255 ---

Timer 0.01 sec(current value)

--- TR0000 ~ TR0511

Timer 0.01 sec(setup value)

--- TS0000 ~ TS0511

Timer 0.1 sec(current value)

--- W9.000 ~ W9.511

Counter (current value) --- CR0000 ~ CR0255

Counter (setup value) --- CS0000 ~ CS0255

--- BD0000 ~ BD4095

--- DI0000 ~ DI4095

--- SI0000 ~ SI4095

--- W30.0000 ~ W30.4094 *2

--- W31.0000 ~ W31.4094 *2

--- W32.0000 ~ W32.4094 *2

--- W33.0000 ~ W33.4094 *3

--- W34.0000 ~ W34.4094 *3

Particulars

Data Memory

File Memory

H/L


9/13


2-3-8

2.3 Fuji Electric


* 2 Define and use 16 bit length data.


* 4 This device cannot write. Use it only for reading.

!!!!!Important

In the LS area, 32-bit devic es are no t sup por ted. Therefore, wh en System A rea addr esses are allocated to B D, DL, or W33 devices,only System A rea (LS0 to LS19) addresses can b e used. Other LS areas, such as the user area, etc. should not b e used.

When u sing the GP-570VM or GP-870VM, do not allocate the Sys- tem Ar ea for B D, DI, or W33 wo rd address es.

Certain PLC mod els and version s may no t be able to perform bit reading or wri t ing .

F30 .. .... .... not poss ible with versions 0.9 or lower F50 .. .... .... not poss ible with versions 1.4 or lower F50H ..... .. not po ssible with version s 0.7 or lower F80 .. .... ... . not poss ible with any version F81 .. .... ... . not poss ible with any version F120 . .... ... not po ssible with any version F200 . .... ... not po ssible with any version

Check the informat ion p la te on the s ide of the PLC to f ind the PLCs version inform ation.

When processing 16-bit single word data:

Internally, the GP basically processes 1 word as 16 bit length data. As a result,the reading and writing of 32 bit length data devices are processed as follows:

Reading From 32 bit data, reads data only from the bottom16 bits.

Writing From 32 bit data, writes data only to the bottom16 bits, as 0 is written to the top 16 bits.

E.g. When data is 12345678 hex.

When processing 2 word 32-bit data:

Two word addresses at bit length 16 are necessary to handle 32 bit long data, but when using a 32 bit device, only one word address needs to be specified.

(from previous page)


10/13


2-3-9

2.3 Fuji Electric


Setup System Area here.

When using a 16 bit device

When using a 32 bit device

FLEX-PC Series

Cannot read the Timer and Counter setup value. However, the write opera-tion is possible only when the PLC is in program mode.



Device Bit Address Word Address

Input Relay X0000 ~ X07FF WX0000 ~ WX07F

Output Relay Y0000 ~ Y07FF WY0000 ~ WY07F

Intemal Relay M0000 ~ M03FF WM000 ~ WM03F

Extended Intemal Relay M0400 ~ M1FFF WM040 ~ WM1FF

Latch Relay L0000 ~ L03FF WL000 ~ WL03F

Extended Latch Relay L0400 ~ L1FFF WL040 ~ WL1FF

Special Relay M8000 ~ M81 FF WM800 ~ WM81FTimer T0000 ~ T03FF ---

Counter C0000 ~ C01FF ---

Timer (current value) --- T0000 ~ T03FF

Timer (setup value) --- TS0000 ~ TS03FF *1

Counter (current value) --- C0000 ~ C01FF

Counter (setup value) --- CS0000 ~ CS01FF *1

Data Register --- D0000 - D2FFF

Special Register --- D8000 ~ D837F

Link Register --- W0000 ~ W3FFF

File Register --- R0000 ~ R7EFF

Particulars

L/H


11/13


2-3-10

2.3 Fuji Electric


When the Timer and Counter setup values are written from the GP, the ladderis changed so that the setup value uses a relative reference. For this reason,be careful when the setup value for the Timer and Counter uses an indirectladder. Normally, access is recommended for indirectly referenced devices.

2.3.4 Environment Setup

The following tables list Digital's recommended PLC and GP communicationsettings.

MICREX-F Series (using PC I/F module FFU120B)

MICREX-F Series (using General Interface Module NC1L-RS2)

Baud Rate 19200 bps Baud Rate 19200 bps

Data Length 7 bits Data Length 7 bitsStop Bit 2 bits Stop Bit 2 bits

Parity Bit Even Parity Bit Even

Data Flow Control ER Control Transfer Condition DTR on/ CTS on

Communication Format(RS-232C)

RS-232C MODE Switch(RS-232C)

1

Communication Format( RS-422)

4-wire type MODE Switch(RS-422)

3

Char. structure Switch 8 (lNlT) is Off

RS-485 Station # setup Switch

(Oniy for RS-485) 0

Unit No. 0 (fixed) ---

FFU120B Setup

---

---

GP Setup


Data Length 8 bits Data Bit 8 bits

Stop Bit 1 bit Stop Bit 1 bit

Parlty Bit None Parity Bit None

Data Flow Control ER Control Transfer Condition DTR on/CTS on

Communication Format RS-232C MODE Setup 1

Character Structure Switch8 (Initialize SetupProcess) is Off (Initial file)

Unit No. 0 (fixed)

---

---

GP Setup NC1L-RS2 Setup

Setup this data in Fi le Def in i t io n . Communication isnot possible when using a Link I/F switch.


!!!!!Important

!!!!!Important


12/13


2-3-11

2.3 Fuji Electric


MICREX-F Series (using PC I/F capsule FFK120A-C10)


Data Length 7 bits Data Length 7 bits

Stop Bit 2 bits Stop Bit 2 bits


Data Flow Control ER Control Transfer Condition None

Communication Format(RS-232C)

RS-232CMODE Switch(RS-232C)

1

Communication Format(RS-422)

4-wire typeMODE Switch(RS-422)

3

RS-485 Station # setup Switch(Only when using RS-485)

0

Unit No. 0 (fixed)

---

---

FFK120A-C10 SetupGP Setup


MICREX-F Series (using PC I/F capsule FFK100A-C10)




Stop Bit 2 bits Stop Bit 2 bits


Data Flow Control ER Control

Communication Format(When using RS-232C)

RS-232C

Unit No. 0 (fixed)

PK access PermittedCode conversion Available

---

---

---

FFK100A-C10 SetupGP Setup

---

!!!!!Important

!!!!!Important


13/13


2-3-12

2.3 Fuji Electric


FLEX-PC Series (using Link I/F)

FLEX-PC Series (using CPU Direct Connection)

MICREX-F Series (FLT-ASFK)



Stop Bit 1 bit

Parity Bit None Parity BitON/OFFEVEN/ODD

OFFNone

Data Flow Control ER Control

Communication Format RS-232C

Unit No. 0

MODE LOADER

Adapter SetupGP Setup

---

---

---

---

---



Stop Bit 1 bit Stop Bit 1 bit


Data Flow Control ER Control Transfer Condition DTR on/ CTS onCommunication Format(RS-232C)

RS-232C MODE Switch(RS-232C)

1

Communication Format(RS-422)

4-wire type MODE Switch(RS-422)

3

Unit No. 1 Station No. 1

Communication Unit / lnterface Module SetupGP Setup

PLC side Setup

Baud Rate 19200 bps(fixed) ---

Data Length 8 bits (fixed) ---

Stop Bit 1 bit (fixed) ---

Parity Bit Odd (fixed) ---

Data Flow Control ER Control (fixed) ---

Communication Format 4-wire type (fixed) ---

Unit No. 1 (fixed) ---

GP Setup

Documents

Fuji PLC Conection 1