Prevent varnish related servo valve failures on small gas turbines and compressor lube oil applications (ie gas transmission compressor units)

Remove & prevent varnish deposits with ICB element technology (Ion Charge Bonding)

Achieve & maintain MPC value < 20 (lower varnish potential)

Lower ISO codes to 14/12/9 with high efficiency post filter element

Extend life of anti-oxidant additives & prevent premature oil replacement

FSTO Turbine Lube Oil Varnish Removal Ideal for maintenance of small turbine lube oil & compressor reservoirs

Fluid Condition Based Solutions From a sample of in-service oil and system details we will help you specify and implement a fluid contamination solution to achieve reliable operation and extend useful fluid life. We know how to stop lube oil varnish before it stops you!

ICB & VTM, the 1, 2 varnish removal punch ICB removes the soluble varnishing building oxidation by-products at the molecular level reversing the process of varnish deposits while VTM removes the gross insoluble by-products for a more rapid reduction in varnish potential. Fluid Compatibility Mineral based turbine oils and specified synthetic Fluids with R&O additive package (non-zinc AW). NOT for use on AW type hydraulic oils, contact Hy-Pro for fluid compatibility & selection. Suitable Operating Temperature Range 90°F/32°C (minimum) to 160°F/71°C (maximum) Operating below minimum can result in reduced Acid and metal ion removal efficiency

Warning: Do not operate above max temperature 160°F/71°C. Contact factory to add pre-cooler before ICB media (operating temp required). High Contamination Fluid Recovery For systems with high acid number, excessive gel / sludge buildup or extremely high water contact Hy-Pro for rapid fluid recovery solutions.

www.hyprofiltration.com

FSTO - Small Turbine & Compressor Lube Oil

HY

-PR

O F

ILT

RA

TIO

N

FSL FILTER CART PART NUMBER GUIDE

- Table 1 Table 2 Table 3

FSTO Power Option -Flow

Rate

Table 1 Flow Rate gpm (lpm)

Code

1 1 gpm (3.7 lpm) reservoir size

up to 1,200 gallons / 4,500 liters

2 2 gpm (7.5 lpm) reservoir size

up to 2,500 gallons / 9,375 liters

0.5 0.5 gpm (1.8 lpm) reservoir size up to 600 gallons / 2,250 liters

FSTO

Table 2 Power Options Code

Omit (std) 115 VAC, 60Hz, 1P (1750 RPM motor)

E1 120 VAC, 50Hz, 1P (1450 motor)

E2 230 VAC, 60Hz, 1P (1750 RPM motor)

E3 230 VAC, 50Hz, 1P (1450 RPM motor)

E5 440-480 VAC, 60 Hz, 3P (1750 RPM motor)

E6 380-420 VAC, 50Hz, 3P (1450 RPM motor)

E7 575 VAC, 60 Hz, 3P (1750 RPM motor)

Model ICB Element x (qty) High Efficiency Element x (qty)

FSTO0.5 ICB-600504-V x (1) HP107L18-VTM710-V x (1)

FSTO1 ICB-600504-V x (2) HP107L18-VTM710-V x (1)

FSTO2 ICB-600524-V x (1) HP107L18-VTM710-V x (1)

FSTO PART NUMBER GUIDE

Special Options

FSTO REPLACEMENT ELEMENT & SEAL KIT ORDER GUIDE

Model Housing Seal Kits

FSTO0.5 SKV-FSJL2

(1 x OVLF, 1 x OVSVR8)

FSTO2 SKV-FSTO2

(1 x OVSVR8, 1 x OVSVR12)

FSTO1 SKV-FSTO1

(1 x OVLF, 1 x OVSVR8)

Contact Hy-Pro for sizing & part selection

www.hyprofiltration.com

Table 3 Special Options Code

A+ Air cooled heat exchanger in-line for operating temp > 160°F / 71°C

C CE Mark

H+ High Temp Shut Off preset for 160°F / 71°C (panel indicator

light included) Temperature setting is adjustable

O+ On-board particle monitor PM-1

X1+ Explosion proof NEC Article 501 Class 1,Div 1, Grp C/D

(contact factory for IEC or ATEX Exp. Proof requirements)

S 304 Stainless steel filter housings, plumbing mix of stainless & plated steel

+Longer lead times. Consult factory.

Inlet \ Outlet Connections Model

All 1” FNPT Inlet & Outlet

3-Way Ball Valve Included on Inlet