Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
LAB
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
Metal handle
BROEN-LAB UNIFLEX™
FRONT CONTROL VALVES
AND OUTLETS
TA B L E O F C O N T E N T S
Content Page
Table of Content 2
BROEN-LAB UNIFLEXTM 4
Product Overview 5
Valves & Outlets
Water ............................................................................................................................................................6-10
Special Water .........................................................................................................................................11-13
Coolant Water .......................................................................................................................................14-15
Burning Gases .......................................................................................................................................16-18
Technical 2.0 Gases / Vacuum / High Flow ..............................................................................19-22
Technical 4.0 Gases / Oxygen ........................................................................................................23-25
Pure 5.0 Gases .......................................................................................................................................26-27
Pure 6.0 Gases .......................................................................................................................................28-29
Corrosive Gases ....................................................................................................................................30-31
Mounting Accessories 32
Mounting InstructionsValves and Outlets for All Media ...................................................................................................................................33
Outlets for Fume Hoods with a Double Wall Construction ..............................................................................33
Pipe InstallationWater / Special Water (SS model) / Technical and Burning Gases (4.0 and 5.0 Gases) ........................34
Special Water (PP models only) / Corrosive Gases 35
WWW.BROEN - L AB . COM- 2 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
B R O E N - L A B U N I F L E X T M
BROEN-LAB UniFlexTM line offers a very high quality and durability combined with the complete program, which ads up to low LCC (Life Cycle Costs). Our line takes the standards in the market to a higher level.
T H I S I S B R O E N - L A B U N I F L E X ™BROEN-LAB UniFlexTM is a unique and patented connection, which allows customers to choose from various connection methods, such as hoses, CU-, PEX of stainless steel pipes, without changing the valve itself. It provides unique flexibility, not only for the installer, but also for the end-user. Due to the flexibility of the system, the quick installation and savings on fit-tings, this system offers lower TIC (Total Installed Costs).
T H I S I S B R O E N - L A B U N I F L E X ™
B R O E N - L A B O F F E R S C U S T O M E R B E N E F I T S
Safe and Simple Installation Complete Range – One Stop Shopping Just-In-Time Deliveries
One Valve – More Connections Approved as a Complete System Customization to Meet Customer Needs
Media Indication According to EN 13792 Uniform Design / Dimensions Fewer connections points
Double Sealing 100 % Testing BROEN-LAB POLYCOAT – Powder Coating
M O R E E F F I C I E N C Y
M O R E P L U G & P L AY
M O R E S I M P L I C I T Y
M O R E Q U A L I T Y
➟➟➟➟
WWW.BROEN - L AB . COM- 4 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
P R O D U C T O V E R V I E W
BROEN-LAB UniFlexTM connection fittings and adaptors for Cu, SS, PEX and PA pipes
For more information about BROEN-LAB UniFlexTM hoses, connection fittings and adaptors, please contact your BROEN-LAB representative or refer to www.BROEN-LAB.com
page 8-10
page 12-13
page 15
page 17-18
page 21-22
page 24-25
page 27
page 29
page 31
OUTLETS
FLANGE(Optional, to be ordered separately,
See page 30)
BROEN-LAB UniFlexTM flexible hoses
WWW.BROEN - L AB . COM - 5 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
FRONT CONTROL VALVES
page 6-7
page 11
page 14
page 16
page 19
page 23
page 26
page 28
page 30
W AT E RF R O N T C O N T R O L V A L V E S
Media Without service valve With service valve
Potable water, cold 25115071001 25115081001
Potable water, hot 25115071002 25115081002
Non-potable water, cold 25115071007 25115081007
Non-potable water, hot 25115071008 25115081008
WPC
WPH
WNC
WNH
Model
Delivered with mounting accessories
Service valve
S P E C I F I C AT I O N SHandle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Headwork: Ceramic Opening/closing function: 180° Temperature range: 0-90°CMax. working pressure: 10 bar / 147 psiTest pressure: 1 x working pressureInlet/outlet: BROEN-LAB UniFlexTM
Weight: 0.7 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: EPDMPlastics: POMLubricant: Silicone basedCeramics: Al-oxyd 96%
O R D E R I N G I N F O R M AT I O NFor standard configuration please refer to the item numbers below.
Other options:
- a valve for different medium - a valve for front side mounting - a valve without mounting kit - national approvals
For further information, please contact your BROEN-LAB representative.
Available with or without service valve according to product numbers listed below
WWW.BROEN - L AB . COM- 6 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
W AT E RF R O N T C O N T R O L V A L V E S - M I X E R
Media regulation cartridge With two step opening cartridge
Potable water, tempered 25115291035 25115311035
Non-potable water, tempered 25115291037 25115311037
Model
Delivered with mounting accessories
S P E C I F I C AT I O N SHandle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Cartridge: Ceramic (with flow and temperature regulation or two step opening)Temperature range: 0-90°CMax.working pressure: 10 bar / 147 psiTest pressure: 1 x working pressureInlet/outlet: BROEN-LAB UniFlexTM
Weight: 0.6 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: EPDMPlastics: POMLubricant: Silicone basedCeramics: Al-oxyd 96%
O R D E R I N G I N F O R M AT I O NFor standard configuration please refer to the item numbers below.
Other options:
- a valve without mounting kit
For further information, please contact your BROEN-LAB representative.
With flow and temperature
WPT
WNT
WWW.BROEN - L AB . COM - 7 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
W AT E RO U T L E T S
S P E C I F I C AT I O N S BROEN-LAB UniFlexTM outlets have an integrated media indication according to EN 13792.Inlet/outlet: BROEN-LAB UniFlexTM
Max. wall thickness: 20mmWeight: 0.5 kg (swivel spout: 0.7 kg)
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: EPDMLubricant: Silicone based
O R D E R I N G I N F O R M AT I O NFor standard configuration please refer to the item numbers below.
Other options:
- other media - flange - non-return valve - fixed nozzle - other standout - straight rear wall connection - wall thickness 20-40mm - double wall mounting - table mounting - additional support in case of a thin panel - national approvals
For further information, please contact your BROEN-LAB representative.
Addional mounting information see page 32-35
Scope of delivery
W I T H R E M O V A B L E N O Z Z L E Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
S
62mm
[2 7/16” ]
107mm [4”]
60mm
[2 1/2” ]
WPC
WPH
WNC
WNH
WPT
WNT
Media 45° S = 53mm S = 75mm S = 90mm
Potable water, cold 25111011001-40 25111111001-40 25111211001-40 25111311001-40
Potable water, hot 25111011002-40 25111111002-40 25111211002-40 25111311002-40
Non-potable water, cold 25111011007-40 25111111007-40 25111211007-40 25111311007-40
Non-potable water, hot 25111011008-40 25111111008-40 25111211008-40 25111311008-40
Potable water, tempered 25111011035-40 25111111035-40 25111211035-40 25111311035-40
Non-potable water, tempered 25111011037-40 25111111037-40 25111211037-40 25111311037-40
WWW.BROEN - L AB . COM- 8 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
W AT E R
W I T H Q U I C K R E L E A S E C O U P L I N G
W I T H S W I V E L S P O U T
O U T L E T S
Media 45° S = 53mm S = 75mm S = 90mm
Potable water, cold 25111021001-40 25111121001-40 25111221001-40 25111321001-40
Potable water, hot 25111021002-40 25111121002-40 25111221002-40 25111321002-40
Non-potable water, cold 25111021007-40 25111121007-40 25111221007-40 25111321007-40
Non-potable water, hot 25111021008-40 25111121008-40 25111221008-40 25111321008-40
Potable water, tempered 25111021035-40 25111121035-40 25111221035-40 25111321035-40
Non-potable water, tempered 25111021037-40 25111121037-40 25111221037-40 25111321037-40
Model / Standout
Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
Delivered with 90° rear wall connection (max wall thickness 20mm)
53mm [2”] U
102mm
[4 “]
WPC
WPH
WNC
WNH
WPC
WPH
WNC
WNH
WPT
WPT
WNT
WNT
Media U = 150mm U = 200mm S = 150mm S = 200mm
Potable water, cold 25112121001-40 25112131001-40 25112141001-40 25112151001-40
Potable water, hot 25112121002-40 25112131002-40 25112141002-40 25112151002-40
Non-potable water, cold 25112121007-40 25112131007-40 25112141007-40 25112151007-40
Non-potable water, hot 25112121008-40 25112131008-40 25112141008-40 25112151008-40
Potable water, tempered 25112121035-40 25112131035-40 25112141035-40 25112151035-40
Non-potable water, tempered 25112121037-40 25112131037-40 25112141037-40 25112151037-40
53mm [2”] S
210mm
[8 1/4”]
S
89mm
104mm
57mm
WWW.BROEN - L AB . COM - 9 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
W AT E RO U T L E T S
B E N C H M O U N T E D O U T L E T W I T H S W I V E L S P O U T
4 5 ° O U T L E T W I T H F I X E D O R S W I V E L S P O U T
Model / Standout
Model / Standout
Media U = 120mm U = 150mm
Potable water, cold 25113041001-40 25113001001-40
Potable water, hot 25113041002-40 25113001002-40
Non-potable water, cold 25113041007-40 25113001007-40
Non-potable water, hot 25113041008-40 25113001008-40
Potable water, tempered 25113041035-40 25113001035-40
Non-potable water, tempered 25113041037-40 25113001037-40
Delivered with 90° rear wall connection (max wall thickness 20mm)
WPC
WPH
WNC
WNH
WPT
WNT
U
300mm
[11 3/4”]
120mm[4 1/2”]
300mm
[11 3/4”]
Media Fixed spout Swivel spout
Potable water, cold 25113071001-40 25113081001-40
Potable water, hot 25113071002-40 25113081002-40
Non-potable water, cold 25113071007-40 25113081007-40
Non-potable water, hot 25113071008-40 25113081008-40
Potable water, tempered 25113071035-40 25113081035-40
Non-potable water, tempered 25113071037-40 25113081037-40
Delivered with 90° rear wall connection (max wall thickness 20mm)
WPC
WPH
WNC
WNH
WPT
WNT
180mm
[7”]180m
m [7”]
WWW.BROEN - L AB . COM- 1 0 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
Special Water
S P E C I A L W AT E RF R O N T C O N T R O L V A L V E S
Media PP valve SS valve
Distilled water 25115331003 25115351003
Deionised water, cold 25115331036 25115351036
WDI
WDC
Model
Delivered with mounting accessories
S P E C I F I C AT I O N SHandle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Headwork: Diaphragm type Opening/closing function: 1 1/2 x 360° Max. working pressure: 10 bar / 147 psiTest pressure: 1 x working pressureWeight: 0.7 kg
M AT E R I A L S W I T H M E D I A C O N TA C T
O R D E R I N G I N F O R M AT I O NFor standard configuration please refer to the item numbers below.
Other options:
- a valve without mounting kit - a valve for front side mounting
For further information, please contact your BROEN-LAB representative.
PP VALVETemperature range: 0-65°C Inlet/outlet: Push couplings for OD10mm pipes
SS VALVETemperature range: 0-90°C Inlet/outlet: BROEN-LAB UniFlexTM
PP VALVEDiaphragm: PTFEPlastics: PP
SS VALVEDiaphragm: PTFE Metals: SS (AISI 316)
Available in PP or Stainless Steel according to product numbers listed below
WWW.BROEN - L AB . COM - 1 1 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
S P E C I A L W AT E R
WDI
WDC
O U T L E T S - P P
S P E C I F I C AT I O N S O R D E R I N G I N F O R M AT I O N
BROEN-LAB UniFlexTM outlets have an integrated media indication according to EN 13792.Inlet: Push couplings for OD10mm pipesMax. wall thickness: 20mmWeight: 0.5 kg
M AT E R I A L S W I T H M E D I A C O N TA C TRubber: EPDMPlastics: PP
For standard configuration please refer to the item numbers below.
Other options:
- flange - wall thickness 20-40mm - swivel spout (U- or S-shape) - additional support in case of a thin panel
For further information, please contact your BROEN-LAB representative.
Addional mounting information see page 32-35
Scope of delivery
PP outlet
Delivered with 90° rear wall connection (max wall thickness 20mm)
Media S = 53mm S = 75mm S = 90mm
Distilled water 25111161003-40 25111261003-40 25111361003-40
Deionised water, cold 25111161036-40 25111261036-40 25111361036-40
W I T H R E M O V A B L E N O Z Z L E Model / Standout
S
62mm
[2 7/16” ]
WWW.BROEN - L AB . COM- 1 2 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
Special Water
S P E C I A L W AT E R
WDI
WDC
O U T L E T S - S S
S P E C I F I C AT I O N S O R D E R I N G I N F O R M AT I O N
BROEN-LAB UniFlexTM outlets have an integrated media indication according to EN 13792.Inlet: BROEN-LAB UniFlexTM
Max. wall thickness: 20mmWeight: 0.5 kg
M AT E R I A L S W I T H M E D I A C O N TA C TRubber: EPDMMetals: Stainless Steel (AISI 316)
For standard configuration please refer to the item numbers below.
Other options:
- flange - straight rear wall connection - fixed nozzle with external G3/4” thread - wall thickness 20-40mm - additional support in case of a thin panel
For further information, please contact your BROEN-LAB representative.
Addional mounting information see page 32-35
Scope of delivery
SS outlet
Delivered with 90° rear wall connection (max wall thickness 20mm)
Media S = 53mm S = 90mm
Distilled water 25111171003-40 25111371003-40
Deionised water, cold 25111171036-40 25111371036-40
W I T H R E M O V A B L E N O Z Z L E Model / Standout
S
62mm
[2 7/16”]
WWW.BROEN - L AB . COM - 1 3 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
C O O L A N T W AT E RF R O N T C O N T R O L V A L V E S
Media Without service valve With service valve
Coolant water, feed 25115031005 25115041005
Coolant water, return 25115031006 25115041006
WCF
WCR
Model
Delivered with mounting accessories
S P E C I F I C AT I O N SHandle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Headwork: Rubber Opening/closing function: 2 x 360° Temperature range: 0-90°CMax. working pressure: 10 bar / 147 psiTest pressure: 1 x working pressureInlet/outlet: BROEN-LAB UniFlexTM Weight: 0.7 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: EPDMLubricant: Silicone based
O R D E R I N G I N F O R M AT I O NFor standard configuration please refer to the item numbers below.
Other options:
- a valve for front side mounting- a valve without mounting kit- a valve with simple hand operation of flow and return of
chilled water
For further information, please contact your BROEN-LAB representative.
Available with or without service valve according to product numbers listed below
Service valve
WWW.BROEN - L AB . COM- 1 4 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
C O O L A N T W AT E RO U T L E T S
S P E C I F I C AT I O N S BROEN-LAB UniFlexTM outlets have an integrated media indication according to EN 13792.Inlet/outlet: BROEN-LAB UniFlexTM
Max. wall thickness: 20mmWeight: 0.5 kg Quick release coupling: double shut-off
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: EPDMLubricant: Silicone based
O R D E R I N G I N F O R M AT I O NFor standard configuration please refer to the item numbers below.
Other options:
- flange - other standout - straight rear wall connection - wall thickness 20-40mm - double wall mounting - additional support in case of a thin panel
For further information, please contact your BROEN-LAB representative.
Addional mounting information see page 32-35
Scope of delivery
W I T H R E M O V A B L E N O Z Z L E A N D I N T E G R AT E D N O N - R E T U R N V A L V E Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
S
84mm
[3 1/2”]
107mm [4”]
60mm
[2 1/2”]
Media 45° S = 53mm S = 75mm S = 90mm
Coolant water, feed 25111041005-40 25111141005-40 25111241005-40 25111341005-40
Coolant water, return 25111041006-40 25111141006-40 25111241006-40 25111341006-40
WCF
WCR
W I T H Q U I C K R E L E A S E C O U P L I N G A N D N O N - R E T U R N V A L V E ( R E T U R N O N LY )
Media 45° S = 53mm S = 75mm S = 90mm
Coolant water, feed 25111021005-40 25111121005-40 25111221005-40 25111321005-40
Coolant water, return 25111051006-40 25111151006-40 25111251006-40 25111351006-40
Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
S
89mm
[3 1/2”]
104mm [4”]
57mm
[2 1/2” ]
WCF
WCR
WWW.BROEN - L AB . COM - 1 5 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
B U R N I N G G A S E SF R O N T C O N T R O L V A L V E S
Media Without service valve With service valve
Natural gas 25115191010 25115201010
25115191012 25115201012
Butane 25115191014 25115201014
Propane 25115191016 25115201016
Acetylene 25115191018 25115201018
Hydrogen 25115191020 25115201020
G
LPG
C H104
C H83
C H22
H2
Model
Delivered with mounting accessories
S P E C I F I C AT I O N S O R D E R I N G I N F O R M AT I O N
Handle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Headwork: ceramic, press/turn Opening/closing function: 90°Max.working pressure: 7 bar / 101,5 psiTest pressure: 1.5 x working pressureInlet/outlet: BROEN-LAB UniFlexTM
Weight: 0.7 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: NBRLubricant: Mineral oil based
For standard configuration please refer to the item numbers below.
Other options:
- a valve for different medium - a valve for front side mounting - a valve without mounting kit
For further information, please contact your BROEN-LAB representative.
Available with or without service valve according to product numbers listed below
Propane/Butane(liquified gases)
Service valve
WWW.BROEN - L AB . COM- 1 6 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
B U R N I N G G A S E SO U T L E T S
S P E C I F I C AT I O N S O R D E R I N G I N F O R M AT I O N
BROEN-LAB UniFlexTM outlets have an integrated media indication according to EN 13792.Inlet/outlet: BROEN-LAB UniFlexTM
Max. wall thickness: 20mmWeight: 0.5 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: NBRLubricant: Mineral oil based
For standard configuration please refer to the item numbers below.
Other options:
- other media - flange - other standout - straight rear wall connection - wall thickness 20-40mm - double wall mounting - table mounting - additional support in case of a thin panel
For further information, please contact your BROEN-LAB representative.
Addional mounting information see page 32-35
Scope of delivery
WWW.BROEN - L AB . COM - 1 7 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
B U R N I N G G A S E S
W I T H F I X E D N O Z Z L E
Media 45° S = 53mm S = 75mm S = 90mm
Natural gas 25111001010-40 25111101010-40 25111201010-40 25111301010-40
25111001012-40 25111101012-40 25111201012-40 25111301012-40
Butane 25111001014-40 25111101014-40 25111201014-40 25111301014-40
Propane 25111001016-40 25111101016-40 25111201016-40 25111301016-40
Acetylene 25111001018-40 25111101018-40 25111201018-40 25111301018-40
Hydrogen 25111001020-40 25111101020-40 25111201020-40 25111301020-40
Model / Standout
G
LPG
C H104
C H83
C H22
H2
Delivered with 90° rear wall connection (max wall thickness 20mm)
S52m
m [2 3/64”]
84mm [3” 1/2]
37mm
[1 1/2” ]
Propane/Butane(liquified gases)
W I T H Q U I C K R E L E A S E C O U P L I N G
Media 45° S = 53mm S = 75mm S = 90mm
Natural gas 25111021010-40 25111121010-40 25111221010-40 25111321010-40
25111021012-40 25111121012-40 25111221012-40 25111321012-40
Butane 25111021014-40 25111121014-40 25111221014-40 25111321014-40
Propane 25111021016-40 25111121016-40 25111221016-40 25111321016-40
Acetylene 25111021018-40 25111121018-40 25111221018-40 25111321018-40
Hydrogen 25111021020-40 25111121020-40 25111221020-40 25111321020-40
Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
S
89mm
[3 1/2”]
104mm [4”]
57mm
[2 1/2” ]
G
LPG
C H104
C H83
C H22
H2
Propane/Butane(liquified gases)
O U T L E T S
WWW.BROEN - L AB . COM- 1 8 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
T E C H N I C A L 2 . 0 G A S E S / V A C U U M / H I G H F L O WF R O N T C O N T R O L V A L V E S
Media Needle Micro flow Needle Micro flow headwork headwork headwork headwork
Compressed air 25115111021 25115461021 25115121021 25115471021
Nitrogen 25115111023 25115461023 25115121023 25115471023
Carbogen Dioxide 25115111024 25115461024 25115121024 25115471024
Argon 25115111025 25115461025 25115121025 25115471025
Helium 25115111026 25115461026 25115121026 25115471026
High flow headwork High flow headwork
Low vacuum (1000 to 1 mbar) 25115151028 25115161028
CA
N2
CO2
Ar
He
V
Model
Delivered with mounting accessories
Available with or without service valve according to product numbers listed below
S P E C I F I C AT I O N S Handle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Inlet/outlet: BROEN-LAB UniFlexTM
Weight: 0.7 kg Test pressure: 1.5 x working pressure
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: FKMPlastics: PVDFLubricant: Perfluoropolyether based
O R D E R I N G I N F O R M AT I O N For standard configuration please refer to the item numbers below.
Other options:
- a valve for front side mounting - a valve without mounting kit For further information, please contact your BROEN-LAB representative.
TECHNICAL 2.0 GASES Headwork: Needle Opening/closing function: 3 x 360° Max. working pressure: 16 bar / 232 psi VACUUM / HIGH FLOW Headwork: High flow Opening/closing function: 1.5 x 360° Max. working pressure: -1 bar to 16 bar / -14.5 psi to 232 psi
Headwork: Micro flow Opening/closing function: 7.5 x 360° Max. working pressure: 16 bar / 232 psi
Without service valve
Please note that valves for vacuum as a standard delivered with a high flow headwork. High flow headwork can also be used for other media where there is a requirement for higher flow.
Service valve
WWW.BROEN - L AB . COM - 1 9 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
T E C H N I C A L 2 . 0 G A S E S P R E S S U R E R E G U L AT O R
Inlet: female BROEN-LAB UniFlex™ with a built-in filter
Outlet: female BROEN-LAB UniFlex™
S P E C I F I C AT I O N S F L O W C H A R T
BROEN-LAB UniFlexTM pressure regulator for panel mounting with a built-in filter (mesh size 200 µm) on the inlet.Type: Non-relievingProof pressure: 15 barOperating pressure: Max. 10 barRegulating pressure range: 0,5-8.5 barInlet/outlet: BROEN-LAB UniFlexTM
Max. panel thickness: 3,5mmWeight: 0.5 kg
M AT E R I A L S W I T H M E D I A C O N TA C T
Metals: Brass, zinc die-castRubber: NBR, FKM Plastics: POMLubricant: Perfluoropolyether based
O R D E R I N G I N F O R M AT I O N
For standard configuration please refer to the item numbers below.
21
Regulator with Built-in Pressure Gauge Series ARG20/30/40
Applicable model
Standard SpecificationsARG30
Air1.5 MPa1.0 MPa
0.05 to 0.85 MPaSet pressure + 0.05 MPa (at relief �ow rate of 0.1 l/min (ANR))
–5 ° to 60 °C (With no freezing)Relieving type
ARG20
ARG40ARG30ARG20
0 to 1.0 MPa
0 to 0.3 MPa
0 to 150 PSI
0 to 45 PSI
Pressuregaugedisplayrange
Standard
Optional
ARG20P-270AS
ARG20P-260S
GB2-10AS
GB2-3AS
GB2-P10AS
GB2-P3AS
ARG30P-270AS
ARG30P-260S
GB3-10AS
GB3-3AS
GB3-P10AS
GB3-P3AS
ARG40P-270AS
ARG40P-260S
GB4-10AS
GB4-3AS
GB4-P10AS
GB4-P3AS
Accessory Part No.
Note 1) Assembly includes a bracket and set nuts.
1/8, 1/4ARG40
1/4, 3/8, 1/21/4, 3/8
75.004.013.0
Conditions: Inlet pressure 0.7 MPa, Outlet pressure 0.2 MPa,Flow rate 20 l/min (ANR)
6
5
4
3
2
1
00 200 400 600 800
Flow rate (l/min)
Out
let p
ress
ure
(bar
)
ARG20 ARG30 Rc3/8 ARG40
04GRA03GRA02GRA
Rc1/2
0
0.6
0.5
0.4
0.3
0.2
0.1
01000 2000 3000
Flow rate ( l/min (ANR))
Out
let p
ress
ure
(MPa
)
Inlet pressure (bar)
Out
let p
ress
ure
(bar
)
2.5
2
1.5
0 2 3 4 5 6 7 8 9 10
Inlet pressure (MPa)
Out
let p
ress
ure
(MPa
)
0.25
0.2
0.15
0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
Inlet pressure (MPa)
Out
let p
ress
ure
(MPa
)
0.25
0.2
0.15
0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
0.6
0.5
0.4
0.3
0.2
0.1
00 500 1000 1500
Flow rate ( l/min (ANR))
Out
let p
ress
ure
(MPa
)
Port sizeFluidProof pressureMaximum operating pressureRegulating pressure rangeRelief pressureAmbient and fluid temperatureConstructionWeight (kg)
Model
Accessory
Bracket assembly (1)
Set nut
Pressuregauge
Flow Characteristics (Representative values) Condition: Inlet pressure 0.7 MPa
Pressure Characteristics (Representative values)
Set point Set point Set point
Media*
Compressed air 2599 366 1099
Nitrogen 2599 366 1099
Carbon Dioxide 2599 366 1099
Argon 2599 366 1099
Model
CA
N2
CO2
Ar
* Can be used for CA, N2, CO2, Ar. Not recommended for Helium (He). Do not use for Oxygen (O2)!
Input pressure p1 = 7 bar
Input pressure p1 = 7 bar
P R E S S U R E C H A R A C T E R I S T I C S
21
Regulator with Built-in Pressure Gauge Series ARG20/30/40
Applicable model
Standard SpecificationsARG30
Air1.5 MPa1.0 MPa
0.05 to 0.85 MPaSet pressure + 0.05 MPa (at relief �ow rate of 0.1 l/min (ANR))
–5 ° to 60 °C (With no freezing)Relieving type
ARG20
ARG40ARG30ARG20
0 to 1.0 MPa
0 to 0.3 MPa
0 to 150 PSI
0 to 45 PSI
Pressuregaugedisplayrange
Standard
Optional
ARG20P-270AS
ARG20P-260S
GB2-10AS
GB2-3AS
GB2-P10AS
GB2-P3AS
ARG30P-270AS
ARG30P-260S
GB3-10AS
GB3-3AS
GB3-P10AS
GB3-P3AS
ARG40P-270AS
ARG40P-260S
GB4-10AS
GB4-3AS
GB4-P10AS
GB4-P3AS
Accessory Part No.
Note 1) Assembly includes a bracket and set nuts.
1/8, 1/4ARG40
1/4, 3/8, 1/21/4, 3/8
75.004.013.0
Conditions: Inlet pressure 0.7 MPa, Outlet pressure 0.2 MPa,Flow rate 20 l/min (ANR)
6
5
4
3
2
1
00 200 400 600 800
Flow rate (l/min)
Out
let p
ress
ure
(bar
)
ARG20 ARG30 Rc3/8 ARG40
04GRA03GRA02GRA
Rc1/2
0
0.6
0.5
0.4
0.3
0.2
0.1
01000 2000 3000
Flow rate ( l/min (ANR))
Out
let p
ress
ure
(MPa
)
Inlet pressure (bar)
Out
let p
ress
ure
(bar
)
2.5
2
1.5
0 2 3 4 5 6 7 8 9 10
Inlet pressure (MPa)
Out
let p
ress
ure
(MPa
)
0.25
0.2
0.15
0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
Inlet pressure (MPa)
Out
let p
ress
ure
(MPa
)
0.25
0.2
0.15
0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
0.6
0.5
0.4
0.3
0.2
0.1
00 500 1000 1500
Flow rate ( l/min (ANR))
Out
let p
ress
ure
(MPa
)
Port sizeFluidProof pressureMaximum operating pressureRegulating pressure rangeRelief pressureAmbient and fluid temperatureConstructionWeight (kg)
Model
Accessory
Bracket assembly (1)
Set nut
Pressuregauge
Flow Characteristics (Representative values) Condition: Inlet pressure 0.7 MPa
Pressure Characteristics (Representative values)
Set point Set point Set point
95 ±2
65
58
47
106 ±
2
BROEN-LAB UniFlexfemale connection
BROEN-LAB UniFlexfemale connection
IN
Build-in filter
Integrated manometer in handle
Ring for panelmounting
IN
OUT
19,5
6
39,
5
Panel thickness: MAX 3,5mm
Mounting information
OUT
Can be used for: CA, N2, CO2 and AR.Not recommended for He.Do NOT use for Oxygen.
C:\LabGroup\16. 2599 - NUMBERS FINAL PRODUCTS\
Inlet / outlet connection:UniFlexUniFlex
234
D
1
C
234
B
1
A
5678
D
C
567
B
8
A
A3
MWA
TFJ
Released on TM No.Pos. Drawn
by:Design
byTMNo.DateRev. Drawn by:Designed by: Date:
Format: 259936610XX
0.363 KgCustomer drawing
Technical gases 2.0
Pressure regulator for panel mounting
24-08-15Change:
Weight:
Description:
Media:
Drawing type:
Comments:
Material:
Specification:
All dimensions maked with are inspection dimensionsUnspecified angular tolerances:Unspecified liniar tolerances:
This drawing is our property and cannot begiven to a third party, copied or otherwiseused without our permission. BROEN-LAB A/S.
Drawing No.:
With build-in filter
Standard specifications:Proof pressure: 15 barMax operating pressure: 10 barRegulating pressure range: 0.5-8.5 barNon-relieving regulatorLeak rate max. 0,01 l /min or 0,6 l /h
Materials in media contact:Rubber, NBRRubber, FKMZinc die-castPOMBrass, CW617N
N N
WWW.BROEN - L AB . COM- 2 0 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
T E C H N I C A L 2 . 0 G A S E S / V A C U U M / H I G H F L O WO U T L E T S
S P E C I F I C AT I O N S O R D E R I N G I N F O R M AT I O N
BROEN-LAB UniFlexTM outlets have an integrated media indication according to EN 13792.Inlet/outlet: BROEN-LAB UniFlexTM
Max. wall thickness: 20mmWeight: 0.5 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: FKM Plastics: PVDFLubricant: Perfluoropolyether based
For standard configuration please refer to the item numbers below.
Other options:
- other media - flange - straight rear wall connection - wall thickness 20-40mm - double wall mounting - table mounting - additional support in case of a thin panel
For further information, please contact your BROEN-LAB representative.
W I T H F I X E D N O Z Z L E
Media 45° S = 53mm S = 75mm S = 90mm
Compressed air 25111001021-40 25111101021-40 25111201021-40 25111301021-40
Nitrogen 25111001023-40 25111101023-40 25111201023-40 25111301023-40
Carbon dioxide 25111001024-40 25111101024-40 25111201024-40 25111301024-40
Argon 25111001025-40 25111101025-40 25111201025-40 25111301025-40
Helium 25111001026-40 25111101026-40 25111201026-40 25111301026-40
Low vacuum (1000 to 1 mbar) 25111001028-40 25111101028-40 25111201028-40 25111301028-40
Model / Standout
CA
N2
CO2
Ar
He
V
Delivered with 90° rear wall connection (max wall thickness 20mm)
S
52mm
[2 3/64” ]
84mm [3 1/2” ]
37mm
[1 1/2” ]
Addional mounting information see page 32-35
Scope of delivery
WWW.BROEN - L AB . COM - 2 1 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
T E C H N I C A L 2 . 0 G A S E S / V A C U U M / H I G H F L O W
W I T H Q U I C K R E L E A S E C O U P L I N G
O U T L E T S
Media 45° S = 53mm S = 75mm S = 90mm
Compressed air 25111021021-40 25111121021-40 25111221021-40 25111321021-40
Nitrogen 25111021023-40 25111121023-40 25111221023-40 25111321023-40
Carbon dioxide 25111021024-40 25111121024-40 25111221024-40 25111321024-40
Argon 25111021025-40 25111121025-40 25111221025-40 25111321025-40
Helium 25111021026-40 25111121026-40 25111221026-40 25111321026-40
Low vacuum (1000 to 1 mbar) 25111021028-40 25111121028-40 25111221028-40 25111321028-40
Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
S
89mm
[3 1/2”]
CA
N2
CO2
Ar
He
V
104mm [4”]
57mm
[2 1/2” ]
WWW.BROEN - L AB . COM- 2 2 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
T E C H N I C A L 4 . 0 G A S E S / O X Y G E NF R O N T C O N T R O L V A L V E S
Needle Micro flow Needle Micro flow Media headwork headwork headwork headwork
Compressed air 25115271021 25115501021 25115281021 25115511021
Oxygen 25115271022 25115501022 25115281022 25115511022
Nitrogen 25115271023 25115501023 25115281023 25115511023
Carbon Dioxide 25115271024 25115501024 25115281024 25115511024
Argon 25115271025 25115501025 25115281025 25115511025
Helium 25115271026 25115501026 25115281026 25115511026
Dinitrogen Monoxide 25115271027 25115501027 25115281027 25115511027
CA
O2
N2
CO2
Ar
He
N O2
Model
Delivered with mounting accessories
S P E C I F I C AT I O N S M AT E R I A L S W I T H M E D I A C O N TA C THandle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Inlet/outlet: BROEN-LAB UniFlexTM
Weight: 0.7 kg Test pressure: 1.5 x working pressure
Headwork: Needle Opening/closing function: 3 x 360° Max. working pressure: 16 bar / 232 psi
Headwork: Micro flow Opening/closing function: 7.5 x 360° Max. working pressure: 16 bar / 232 psi
Metals: BrassRubber: FKMPlastics: PVDFLubricant: Perfluoropolyether based (Oxygen approved)All components are ultrasonically cleaned for 99,99% clean gases
O R D E R I N G I N F O R M AT I O N For standard configuration please refer to the item numbers below.
Other options:
- a valve for front side mounting - a valve without mounting kit For further information, please contact your BROEN-LAB representative.
Available with or without service valve according to product numbers listed below
Without service valve
Service valve
WWW.BROEN - L AB . COM - 2 3 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
T E C H N I C A L 4 . 0 G A S E S / O X Y G E NO U T L E T S
S P E C I F I C AT I O N SBROEN-LAB UniFlexTM outlets have an integrated media indication according to EN 13792.Inlet/outlet: BROEN-LAB UniFlexTM
Max. wall thickness: 20mmWeight: 0.5 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: FKMPlastics: PVDFLubricant: Perfluoropolyether based (Oxygen approved)All components are ultrasonically cleaned for 99,99% clean gases
O R D E R I N G I N F O R M AT I O N For standard configuration please refer to the item numbers below.
Other options:
- other media - flange - removable nozzle - other standout - straight rear wall connection - wall thickness 20-40mm - table mounting - additional support in case of a thin panel
For further information, please contact your BROEN-LAB representative.
Addional mounting information see page 32-35
Scope of delivery
WWW.BROEN - L AB . COM- 2 4 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
T E C H N I C A L 4 . 0 G A S E S / O X Y G E N
W I T H F I X E D N O Z Z L E
Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
CA
O2
N2
CO2
Ar
He
N O2
Media 45° S = 53mm S = 75mm S = 90mm
Compressed air 25111081021-40 25111181021-40 25111281021-40 25111381021-40
Oxygen 25111081022-40 25111181022-40 25111281022-40 25111381022-40
Nitrogen 25111081023-40 25111181023-40 25111281023-40 25111381023-40
Carbon dioxide 25111081024-40 25111181024-40 25111281024-40 25111381024-40
Argon 25111081025-40 25111181025-40 25111281025-40 25111381025-40
Helium 25111081026-40 25111181026-40 25111281026-40 25111381026-40
Dinitrogen monoxide 25111081027-40 25111181027-40 25111281027-40 25111381027-40
S52m
m [2 3/64” ]
84mm [3 1/2” ]
37mm
[1 1/2” ]
O U T L E T S
CA
O2
N2
CO2
Ar
He
N O2
Media 45° S = 53mm S = 75mm S = 90mm
Compressed air 25111851021-40 25111861021-40 25111871021-40 25111901021-40
Oxygen 25111851022-40 25111861022-22 25111871022-22 25111901022-22
Nitrogen 25111851023-40 25111861023-40 25111871023-40 25111901023-40
Carbon dioxide 25111851024-40 25111861024-40 25111871024-40 25111901024-40
Argon 25111851025-40 25111861025-40 25111871025-40 25111901025-40
Helium 25111851026-40 25111861026-40 25111871026-40 25111901026-40
Dinitrogen monoxide 25111851027-40 25111861027-40 25111871027-40 25111901027-40
W I T H Q U I C K R E L E A S E C O U P L I N G
Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
S
89mm
[3 1/2”]
104mm [4”]
57mm
[2 1/2” ]
WWW.BROEN - L AB . COM - 2 5 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
P U R E 5 . 0 G A S E SF R O N T C O N T R O L V A L V E S
Media Shut-off valve Needle headwork Micro flow headwork
Compressed air 25115431021 25115421021 25115531021
Oxygen 25115431022 25115421022 25115531022
Nitrogen 25115431023 25115421023 25115531023
Carbon Dioxide 25115431024 25115421024 25115531024
Argon 25115431025 25115421025 25115531025
Helium 25115431026 25115421026 25115531026
Model
Delivered with mounting accessories
CA
O2
N2
CO2
Ar
He
S P E C I F I C AT I O N S Valve can be used for non-corrosive and inactive gases with purity coefficient up to 5.0 (99.999% pure gases).Handle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Inlet/outlet: BROEN-LAB UniFlexTM
Leak rate: < 5x10-5 mbar x l/s [Helium]
Weight: 0.7 kg Test pressure: 1.5 x working pressure
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: FKMPlastics: PVDFLubricant: Perfluoropolyether based (Oxygen approved)All components are ultrasonically cleaned for 99,999% clean gases
O R D E R I N G I N F O R M AT I O NFor standard configuration please refer to the item numbers below.
Other options:
- a valve for front side mounting - a valve without mounting kit - inlet/outlet with female 1/4 NPT thread
For further information, please contact your BROEN-LAB representative.
FLOW VALVESHeadwork: Needle Opening/closing function: 3 x 360° Max. working pressure: 21 bar / 305 psi SHUT-OFF VALVEHeadwork: StopOpening/closing function: 1.5 x 360° Max. working pressure: 21 bar / 305 psi
Headwork: Micro flow Opening/closing function: 7.5 x 360° Max. working pressure: 16 bar / 232 psi
WWW.BROEN - L AB . COM- 2 6 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
P U R E 5 . 0 G A S E SO U T L E T S
Media 45° S = 53mm S = 75mm S = 90mm
Compressed air 25111091021-40 25111191021-40 25111291021-40 25111391021-40
Oxygen 25111091022-40 25111191022-40 25111291022-40 25111391022-40
Nitrogen 25111091023-40 25111191023-40 25111291023-40 25111391023-40
Carbon dioxide 25111091024-40 25111191024-40 25111291024-40 25111391024-40
Argon 25111091025-40 25111191025-40 25111291025-40 25111391025-40
Helium 25111091026-40 25111191026-40 25111291026-40 25111391026-40
Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
S P E C I F I C AT I O N S Outlets can be used for non-corrosive and inactive gases with purity coefficient up to 5.0 (99,999% pure gases).BROEN-LAB UniFlexTM outlets have an integrated media indi-cation according to EN 13792.Inlet: BROEN-LAB UniFlexTM
Outlet: Female 1/4 NPTLeak rate: < 5x10-5 mbar x l/s [Helium]Max. wall thickness: 20mmWeight: 0.5 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassRubber: FKMPlastics: PVDFLubricant: Perfluoropolyether based (Oxygen approved)All components are ultrasonically cleaned for 99,999% clean gases.
O R D E R I N G I N F O R M AT I O N For standard configuration please refer to the item numbers below.
Other options:
- other media - flange - straight rear wall connection - wall thickness 20-40mm - table mounting - additional support in case of a thin panel - Swagelok® tube fittings - inlet with female 1/4 NPT thread
For further information, please contact your BROEN-LAB representative.
S
27mm
[1” ]
84mm [3 1/2” ]
CA
O2
N2
CO2
Ar
He
Addional mounting information see page 32-35
Scope of delivery
WWW.BROEN - L AB . COM - 2 7 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
P U R E 6 . 0 G A S E SF R O N T C O N T R O L V A L V E S
Media Stop valve Flow valve
All media 02 460.009-9023 02 462.009-9023
Model
Delivered with mounting accessories
S P E C I F I C AT I O N S O R D E R I N G I N F O R M AT I O N
Valve can be used for non-corrosive and inactive gases with purity coefficient up to 6.0 (99.9999% pure gases).Handle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Headwork: Diaphragm typeOpening/closing function: 1.5 x 360° Max. working pressure: 21 bar / 305 psiTest pressure: 1.5 x working pressureInlet/outlet: Female 1/4” NTP threadLeak rate: < 10-7 mbar x l/s [Helium]Weight: 0.7 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: BrassPlastics: PVDFDiaphragm: Stainless Steel Alloy
For standard configuration please refer to the item numbers below.
Media should be defined when ordering.
Other options:
- Swagelok® tube fittings
For further information, please contact your BROEN-LAB representative.
WWW.BROEN - L AB . COM- 2 8 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
P U R E 6 . 0 G A S E SO U T L E T S
Swagelok® tube fittings must be ordered separately
S P E C I F I C AT I O N S
Outlets can be used for non-corrosive and inactive gases with purity coefficient up to 6.0 (99,9999% pure gases).Inlet/outlet: Female 1/4 NPT threadLeak rate: < 10-7 mbar x l/s [Helium]Weight: 0.5 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: Brass (Stainless Steel for bulk head union outlet)
O R D E R I N G I N F O R M AT I O N For standard configuration please refer to the item numbers below.
Swagelok® tube fittings must be ordered separately.
For further information, please contact your BROEN-LAB representative.
Media 45° Straight Bulk head union outlet
All media 02 869.529-9023 02 861.529-9023 02 566.009-9023
Models
Delivered with 90° rear wall connection (max wall thickness 20mm)
WWW.BROEN - L AB . COM - 2 9 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
C O R R O S I V E G A S E SF R O N T C O N T R O L V A L V E S
Media Without service valve
Corrosive gases 25115391099
Model
Delivered with mounting accessories
S P E C I F I C AT I O N S O R D E R I N G I N F O R M AT I O N
Valve can be used for corrosive gases with purity coefficient up to 6.0 (99.9999% pure gases).Handle: Metal, BROEN-LAB POLYCOAT powder coated with media indication according to EN13792.Headwork: Diaphragm typeOpening/closing function: 1.5 x 360° Max. working pressure: 16 bar / 232 psiTest pressure: 1.5 x working pressureInlet/outlet: SS tubes for OD 8mmLeak rate: < 10-7 mbar x l/s [Helium]Weight: 0.7 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: Stainless Steel (AISI 316L)Plastics: PVDF
For standard configuration please refer to the item numbers below.
Media should be defined when ordering.
Other options:
- a valve without mounting kit
For further information, please contact your BROEN-LAB representative.
WWW.BROEN - L AB . COM- 3 0 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
C O R R O S I V E G A S E SO U T L E T S
Addional mounting information see page 32-35
S P E C I F I C AT I O N S
Outlets can be used for corrosive gases with purity coefficient up to 6.0 (99.9999% pure gases).BROEN-LAB UniFlexTM outlets have an integrated media indication according to EN 13792.Inlet: OD 8mm / ID 6mmLeak rate: < 10-7 mbar x l/s [Helium]Max. wall thickness: 20mmWeight: 0.6 kg
M AT E R I A L S W I T H M E D I A C O N TA C TMetals: Stainless Steel (AISI 316L)Plastics: PVDF
O R D E R I N G I N F O R M AT I O N For standard configuration please refer to the item numbers below.
Media should be defined when ordering.
Other options:
- flange - wall thickness 20-40mm - additional support in case of a thin panel
For further information, please contact your BROEN-LAB representative.
Scope of delivery
W I T H F I X E D N O Z Z L E
Media S = 53mm S = 75mm S = 90mm
Corrosive gases 25111501099-40 25111511099-40 25111521099-40
Model / Standout
Delivered with 90° rear wall connection (max wall thickness 20mm)
S
52mm
[2 3/64” ]
WWW.BROEN - L AB . COM - 3 1 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
M O U N T I N G A C C E S S O R I E S
Illustration Description Media BROEN-LAB item No.
Flange (wall thickness 0-20mm) All media 1521057G
Flange (wall thickness 20-40mm) All media 1521178G
Nut (wall thickness 20-40mm) All media 1521054
Nut (max. wall thickness 20mm) All media 1521036
Straight rear wall connection Water, burning and 1521088 2.0 technical gases
90° rear wall connection Water, burning and 1521052 2.0 technical gases
Backside support All media 1521092
Rear wall connection for fume hoods Water, burning and with a double wall construction 2.0 technical gases M = 49 to 61 mm 2511494 M = 61 to 73 mm 2511497 M = 73 to 85 mm 2511496 M = 85 to 97 mm 2511495 M = 97 to 109 mm 2511493
Test equipment for outlets 2.0 technical gases 1521177
Ø41m
mØ
41mm
34mm
22mm
40mm
M22mm
40m
m
WWW.BROEN - L AB . COM- 3 2 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
M O U N T I N G I N S T R U C T I O N S
Max. 30mm
F R O N T C O N T R O L V A L V E S
1 )
1 )
2 )
2 )
O U T L E T S
Drill Ø41mmM40x1.5
Tighten the mounting nut with hand
25Nm
Tighten Allen screws with Allen key, max. 1Nm
Flange (optional) Mandatory on soft wall materials
Max. 20mmMax. 18mm incl. flange
Drill Ø18mm hole in wall
Drill Ø22mm hole in wall
Wall thickness 20-40mm
Wall thickness less than 20mm
Flange (optional) Mandatory on soft wall materials
A L L M E D I A
43mm
WWW.BROEN - L AB . COM - 3 3 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
M O U N T I N G I N S T R U C T I O N S
M O U N T I N G O F O U T L E T S I N T O F U M E H O O D S W I T H A D O U B L E W A L L C O N S T R U C T I O N
Drill Ø28mm hole
1) Insert the rear wall connection through the back wall 2) Fix the outlet to the back wall by tightening the nut
5) Tighten Allen screws with Allen key, max 1Nm
3) Place the front wall
4) Position the outlet
P I P E I N S TA L L AT I O N W AT E R / S P E C I A L W AT E R ( S S M O D E L ) / T E C H N I C A L A N D B U R N I N G G A S E S ( 4 . 0 A N D 5 . 0 G A S E S )
BROEN-LAB front control valves and fume hood outlets for standard media are delivered with BROEN-LAB UniFlexTM inlet con-nections as well as outlet connection on the valves.
Pipe installation can be done either with flexible hoses or with standard Cu, PEX or SS pipes.
BROEN-LAB has a wide range of flexible hoses available with BROEN-LAB UniFlexTM connections as well as connection fittings to fit pipes of the following sizes:
- OD 8mm- OD 10mm- OD 12mm- OD 15mm- 3/8”
For further information about flexible hoses and connection fittings, please contact you local BROEN-LAB representative or refer to www.BROEN-LAB.com
V A L V E O U T L E T
BROEN-LAB UniFlexTM connection
BROEN-LAB UniFlexTM connection fittings and adaptors for Cu, SS, PEX and PA pipes
BROEN-LAB UniFlexTM flexible hoses
WWW.BROEN - L AB . COM- 3 4 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
P I P E I N S TA L L AT I O N S P E C I A L W AT E R ( P P M O D E L S O N LY )
C O R R O S I V E G A S E S
Please note that PP valves and outlets for special water are delivered with push-in fittings.
BROEN-LAB recommends the following materials for pipe installation:
Please note that valves and outlets for corrosive gases are delivered in stainless steel and are prepared for orbital welding.
In case of outlet, welding process should take place before mounting into the fume hood.
BROEN-LAB recommends the following materials for pipe installation:
- PVDF (can be purchased at BROEN-LAB), LLDPE, PUR
For further information, please contact your BROEN-LAB representative or refer to www.BROEN-LAB.com
For further information, please contact your BROEN-LAB representative or refer to www.BROEN-LAB.com
V A L V E O U T L E T
V A L V E O U T L E T
Push-in fittings for OD10mm plastic tubing (10x1mm)
OD 8mm / ID 6mm
WWW.BROEN - L AB . COM - 3 5 -
BR
OEN
-LAB
UN
IFLEXTM FR
ON
T CO
NTR
OL V
ALV
ES AN
D O
UTLETS
www.BROEN-LAB.com
BROEN-LAB A/S ISO 9001 certi� cation In September 1991 BROEN-LAB A/S was certi� ed according to ISO 9001 as one of the � rst Danish companies. The certi� cation was carried out by Bureau Veritas, Denmark, for our Danish site in Assens.The quality management system of BROEN-LAB A/S now complies with detailed speci� cations laid down by the internationally acknowledged EN ISO 9001:2015. This certi� cation will further contribute to reputation for quality and reliability of BROEN-LAB A/S.
HEAD OFFICE
BROEN-LAB A/SDrejervaenget 2 • DK-5610 AssensDenmarkTel.: +45 6376 6376 • Fax +45 6471 2476E-mail: [email protected]
INTERNATIONAL OFFICES
BROEN-LAB LtdTel. +44 121 522 4515E-mail: [email protected]
BROEN-LAB Singapore Pte. Ltd.25 International Business Park #04-60A German Centre Singapore 609916Tel. +65 6298 0662 • Fax +65 6298 0468E-mail: [email protected]
BROEN-LAB GmbHTel.: +45 6376 6376 • Fax +45 6471 2476E-mail: [email protected]
BROEN-LAB Sverige ABTel.: +45 6376 6376 • Fax +45 6471 2476E-mail: [email protected]
BROEN-LAB Inc.15 Constitution Drive Suite 122 Bedford • NH 03110 • USA Tel.: +1 603 310 5089 E-mail: [email protected]
BROEN-LAB develops, manufactures and sells Laboratory Fittings, Emergency Shower Systems and Eye Wash Systems into a broad spectrum of laboratories and industrial loca-tions; sectors include Pharmaceutical, Food&Beverage and Academia. Our expertise and product quality ensure optimal solutions compliant to all relevant international norms setting new standards in risk mitigation in modern research and development facilities.
BROEN-LAB offer solutions that ensure the functionality,compliance, hygiene, durability and safety are of the highest priority. For over 50 years our products have been integrated into a wide variety of workplaces, laboratories, hospitals and industrial locations, with features that are assessed and de-signed to be flexible, durable and compliant offering a broad range of options tailored to each location. This inherent design integrity provides confidence in the solution adopted wherever in the world these are applied.
BROEN-LAB is a collaboration partner in the design andlayout of your next laboratory and it’s integrated safetysolutions.
99B0
040
BRO
EN-L
AB
UN
IFLE
XTM F
VC
MET
AL
HA
ND
LE -
09.
2021