3
Page 1 of 3 Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors. Published 04/07/2019 Technical Guide Dimensions are nominal measurements only. To see the complete Franke range go to www.reece.com.au/bathrooms Franke Olten Gooseneck Pull Out Sink Mixer Matte Black (4*) SPECIFICATIONS Recommended Use Domestic Colour Brushed Black Material Stainless Steel Recommended Pressure Range 150 - 500 kPa Max Continuous Working Pressure 500 kPa Suitable for Storage Tank Hot Water Yes Suitable for Continuous Flow Hot Water Yes Suitable for Gravity Feed Hot Water No WARRANTY Warranty 15 years* Please refer to Warranty Page for full terms and conditions CLEANING RECOMMENDATIONS: We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions The more stars the more water efficient WATER RATING PR Kitchen & Washroom Systems www.waterrating.gov.au In accordance with AS/NZS 6400 License No. 1384 7.5 litres per minute *Tap Support Included

Franke Olten Gooseneck Pull Out Sink Mixer Matte Black (4*) · Franke Olten Mixer Care Instructions –Periodically clean the aerator filter –Install filter valves under the sink

  • Upload
    others

  • View
    7

  • Download
    0

Embed Size (px)

Citation preview

  • Page 1 of 3

    Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.Published 04/07/2019

    Technical Guide

    Dimensions are nominal measurements only.

    To see the complete Franke range go to www.reece.com.au/bathrooms

    Franke Olten Gooseneck Pull Out Sink Mixer Matte Black (4*)

    SPECIFICATIONSRecommended Use DomesticColour Brushed BlackMaterial Stainless SteelRecommended Pressure Range 150 - 500 kPaMax Continuous Working Pressure 500 kPaSuitable for Storage Tank Hot Water YesSuitable for Continuous Flow Hot Water YesSuitable for Gravity Feed Hot Water No

    WARRANTYWarranty 15 years*Please refer to Warranty Page for full terms and conditions

    CLEANING RECOMMENDATIONS:We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions

    The more stars the more water efficient

    WATER RATING

    PR Kitchen & Washroom Systems

    www.waterrating.gov.au

    In accordance with AS/NZS 6400

    License No. 1384

    7.5 litres perminute

    *Tap Support Included

  • Page 2 of 3

    FRANKEFranke Olten Mixer Installation Instructions

  • Page 3 of 3

    FRANKEFranke Olten Mixer Care Instructions– Periodically clean the aerator filter– Install filter valves under the sink and periodically clean the filters– Do not use detergents, solvents, chemial agents, abrasive sponges, wire wool or alcohol etc.which would irreparably damage the surface of the product and ruin its appearance, sheen andmatte finishes.– Clean with soapy water and dry with a soft cloth– Dry the product after use if the water is very hard or aggressive, as it may leave deposits, whichwould damage the surface.– Do not install the tap when the water pressure exceeds 500kPa (in this case, pressure limitingvalves are required.– Rinse the water pipes before installing the tap