Formwork Scaffolding Engineering The most appropriate ... · PDF fileFormwork Scaffolding Engineering The most appropriate solution ... formwork for building construction and civil

DE

en 0

4 | 2

014

Xxx

©

PE

RI G

mbH

Formwork Scaffolding EngineeringThe most appropriate solution for each and every requirement

PERI GmbHFormwork Scaffolding EngineeringRudolf-Diesel-Straße 1989264 Weissenhorn, GermanyTel. +49 (0)7309.950-0Fax +49 (0)[email protected]

Important Notes

Without exception, all current safety regulations and guidelines must be observed in those countries where our products are used.

The photos shown in this brochure feature construction sites in progress. For this reason, safety and anchor details in particular cannot always be considered as conclusive or final. These are subject to the risk assess-ment carried out by the contractor.

The systems or items shown are not necessarily available in all countries.

Safety instructions and load specifications are to be strictly observed at all times. Separate structural calculations are required for any deviations from the standard design data.

The information contained herein is subject to technical changes in the interests of progress. Errors and typographical mistakes reserved.

Edition 04 | 2014

Content

Wall Formwork 2

Column Formwork 4

Slab Formwork 5

Shoring Systems 6

Working Scaffolds 8

Access 9

Protection Scaffolds 10

Climbing Systems 10

Civil Engineering Technology 12

Special Formwork 13

System-Independent Components 13

Services 15

Formwork Scaffolding Engineering 1

Wall Formwork

MAXIMO Panel FormworkTime-saving forming with MX tie technology resulting in the best concrete finishes

FasterOne-sided tie operations without spacer tubes and conesEfficientSystematized tie points, reduced num-ber of ties

Neat and tidy arrangementImproved concrete finish, regular joint and tie arrangement

VARIO GT 24 Girder Wall FormworkThe flexible wall formwork – also for high-grade architectural concrete surfaces

Cost-effectiveVariable, project-specific arrangement of lattice girders and walersAdaptableTie positioning and joint pattern design according to planning requirements

Well thought-outElongated holes in walers and couplings allow continuous compensation

LIWA Panel FormworkThe lightweight wall formwork with a cleverly designed corner solution

VersatileLow weight, only four system heights and five panel widthsSpecial featureEach standard panel is simultaneously a multi-purpose panel with a perforated strip

UncomplicatedInset tie points, extensive range of accessories

TRIO Panel FormworkFast forming operations due to large-sized elements with only one connecting part

SimpleOnly one connecting part – the BFD alignment couplerGenerously-dimensionedUp to 2.40 m x 2.70 m sized panels

CleverFew panel sizes and well thought-out accessories, flexible application possibili-ties

DOMINO Panel FormworkThe lightweight panel formwork for building construction and civil engineering

LightweightLow dead weight and only four panel widthsPracticalOne component for all connections - the DRS alignment coupler

UncomplicatedInset tie points, extensive range of accessories

2 Formwork Scaffolding Engineering

RUNDFLEX Circular Wall FormworkContinuously adjustable formwork for radii greater than 1.00 m – without panel alterations

UncomplicatedThree different panel widths and one connection partReliableContinuous adjustment of the radii of all panels

VariableFlexible and easily adjustable for wall internal radii of 1.00 m and more

RUNDFLEX Plus Circular FormworkEasy operations and adjustment of all curvatures for diameters of 2.50 m and more

User-friendlyOnly 0.54 ties per square metre of wallEfficientLow number of spindles, easy adjust-ment of radii

Cost-effectiveAnchoring above the top edge of the panel saves one layer of ties in the concrete

GRV Articulated Waler Circular FormworkEconomical forming without ties – for all radii

Cost-effectiveClosed formwork ring without ties, very economical for watertight containersContinuously adjustableAdjustable for concrete internal radii of 90 cm and more

VersatileCan also be used for arches in bridges or vaults

SB Brace FrameReliable concreting of single-sided walls up to 8.75 m high

FastAll required connection parts are already mounted on the brace frameMobileAll individual components have been designed to fit the load capacity of trucks and containers

CompatibleCan be combined with MAXIMO, VARIO, TRIO, DOMINO, RUNDFLEX and RUNDFLEX Plus

RS Push-Pull PropsA complete programme, can be telescoped to reach a length of 14.00 m

Extremely quickRough adjustment in 10 cm increments within seconds, fine adjustment with only a few turnsDurableGalvanized to ensure a very long service life

SafeAll length extensions are carried out safely from the installation areaVariableAccessories have been designed to en-sure safe fixation even on prefabricated concrete elements


Column Formwork

QUATTRO Column FormworkThe column formwork which can be moved as a complete unit

Time-savingTightened or separated with only a few simple movementsVariableCross-sections in 5 cm increments with edge lengths from 20 cm to 60 cm

SafeConcreting platform with integrated access ladder and ladder safety cage

VARIO GT 24 Column FormworkAll heights and all cross-sections regardless whether square or rectangular-shaped

Continuously variableColumn cross-sections of up to 80 cm x 120 cm.StandardizedEach waler line has only two clamping parts taken from the VARIO standard programme

RobustRegular fresh concrete pressure up to 100 kN/m², adaptable to higher pres-sures if required

RAPID Column FormworkFor highly demanding concrete surfaces without nail or screw impressions

FastThree frame heights allow optimal height adjustmentCrane-independentBasic assembly by hand with lightweight aluminium elements

Neat and tidyFreely-selectable formlining for the highest architectural concrete require-mentsContinuously adjustableFor cross-sections of up to 60 cm edge length

TRIO Column FormworkPanel formwork elements for columns

VersatileAdaptable in 5 cm increments for rec-tangular columns with edge lengths of up to 75 cm CleverNo nailing of chamfer strips thanks to the clamping mechanism and PERI strips

UsefulConcreting platform is continuously adjustable; integrated ladder for safe access

LICO Column FormworkThe lightweight column formwork for cost-effective forming by hand

Practice-orientedWell thought-out details simplify the application and reduce shuttering timesFlexibleOnly three different element heights

CombinableRectangular cross-sections in 5 cm increments up to 60 cm x 60 cm


SRS Circular Column FormworkHigh-quality formwork made of steel for the best concrete surfaces

VariableColumn diameter adaptable in 5 cm increments from 25 cm to 70 cmTwo-pieceFast assembly with only two column halves and integrated spanner

ExtendableFour element heights for height adjust-ments in 30 cm increments

Slab Formwork

SKYDECK Aluminium Panelized Slab FormworkThe slab formwork with short forming times

FastDepending on the strength of concrete and the slab thickness, early striking is possible after only one dayLightweightAluminium individual components weigh a maximum 16 kg

EfficientWith a systematic assembly sequence and a minimum number of slab propsCompleteWith a comprehensive range of safety accessories such as platforms and guardrails

GRIDFLEX Grid Element Slab FormworkThe flexible slab formwork for simple and safe assembly

SafeSystematic assembly of the girder grid from the slab belowUncomplicatedFew system components: prop head, one standard and two filler elements

AdaptableFast adaptation to the structural form with filler elementsVariableFree choice of formlining according to project-specific requirements

MULTIFLEX Girder Slab FormworkThe universal girder slab formwork system for any ground plan and all floor heights

AdaptableAdaptable to all floor plans due to the flexible arrangement of the girdersCost-effectiveGirder and prop selection depending on the slab thickness and support height

VariableFree choice of formlining according to project-specific requirements


Table Module VT Slab TableThe completely pre-assembled standard table for a low frequency of use

CompleteCompletely pre-assembled in 4 standard sizesPracticalWith bracing also usable as cantilevered edge table

UsefulWith swivel-mounted slab props for moving under beams

SKYTABLE Slab TableThe large-sized slab table for areas of up to 150 m² – movable in one crane lift

FastEasy lowering without effort and large lowering rangesSafeRemote-controlled moving procedure from a safe position on the slab edge

AdaptableCan be used for different storey heights with props or shoring towers

Shoring Systems

PEP/PEP Ergo Slab PropsMade of galvanized steel with high load-bearing capacity and low weight

RobustPEP props can carry up to 50 kNTrend-settingAdjusting nut with lowering nib and captive handgrip

Well thought-outProp heads can be mounted on the inner and outer tubes

VARIODECK Steel Waler Slab TableFormwork for large areas and heavy pre-fabricated parts

Ready for usePre-assembled tables with almost 16 m² forming surfaceStrongFor large cantilevers and heavy pre-fabricated parts such as parapet elements

CompactProps can be folded up for quick and easy movement


HD 200 Heavy-Duty PropThe lightweight prop for loads up to 200 kN

UncomplicatedTool-free assembly of the individual sec-tions with captive connectionsExtremely practicalEven loads of 20 t can be lowered in a controlled manner – simply with a cord-less screwdriver

Connections with high tensile strengthCan be coupled with system main beams for longer structures

ST 100 Stacking TowerThe efficient shoring system consisting of framed supports with few system components

Fast assemblyBy simply fitting the components to-gether with no pins and connectorsQuickly plannedEvery working height is simple to plan without the need of combination tables

Quickly explainedAssembled to any required height using only five system components

PD 8 Slab Table, Shoring and Stair TowerThe proven shoring system for large loads

SimpleStandard connecting parts and identical framesHugeUsed as slab table for high clearances

High load-bearing capacityAs shoring tower over 20 m high and more than 60 t loadHighAs stair tower up to 100 m high

MULTIPROP Post ShoresUsed as a cost-saving lightweight individual prop and cost-effective shoring tower

High load-bearing capacityUp to 90 kN in accordance with the type testWell thought-outWith self-cleaning thread and robust, free-running collar

PracticalThe integrated measuring tape on the inner tube shows the complete length of the propExpandableWith MULTIPROP frames, can also be used as a shoring tower

PERI UP Rosett Flex ShoringThe maximum level of flexibility in shoring solutions

ModularWith uniform grid size in all three dimen-sionsDimensionally stableCan be moved in large units due to the high rigidity of the ledger connections

CompatibleLoad transfer aligned with PERI form-work systems


VARIOKIT Heavy-Duty Shoring TowerHeavy-duty shoring for civil engineering projects

StrongFor leg loads of up to 700 kNCost-effectiveWith rentable system components taken from the engineering construction kit

FlexibleAs shoring tower, tower with legs,shoring tower frame, birdcage scaffold-ing or main beam frame

Working Scaffolds

PERI UP T 72 / T 104 Frame ScaffoldingThe facade scaffolding with safety integrated in the system

SafeCollective fall protection without addi-tional components through the guardrail in advanceLightweightEasy to handle parts with low weights

SecureAfter the deck has been placed and moved sideways, the integrated lock against lift off is immediately securedComprehensiveReliable side protection – outside and inside

PERI UP R 72 / R 104 Modular ScaffoldFor challenging building forms and complex facades

Practically unlimitedOptimal adjustment possibilities regarding height, width and lengthExtremely easy to assembleFast and safe assembly with the “Gravity Lock”

Reassuringly safeNo additional components required due to the integrated lock against lift off

PERI UP Reinforcement ScaffoldEasy implementation using the modular design principle, standing heights of up to 10.80 m without anchors

Very stableCan be assembled in front of formwork and walls without anchors and ballastQuickly plannedFast calculation of material requirements thanks to the modular design principle

Movable large-sized table unitsComplete units can be moved due to connections with high tensile strength


PERI UP Rosett Flex Modular ScaffoldingThe working scaffold with a 25 cm grid system and maximum flexibility

Safe working conditionsWorking platforms completely covered without any gaps, simple conversions to accommodate any obstructionsNon-slipHigh level of slip resistance thanks to the perforated decking surface

Easy to installQuick and safe assembly with the “Gravity Lock” and self-locking decksHigh load-bearing capacitySpecial node rigidity and high loadability of the connection

PERI UP Rosett Staircase Alu 64Lightweight stair tower with a 2.00 m height grid arrangement up to 90 m high

Easily erectedLightweight flights of stairs for quick assemblySimple to planQuick planning thanks to the modular design principle with three units (Basis, Plus and Top)

Extremely versatile in useAs scaffold for accessing higher-posi-tioned working areas, as suspended scaffold for reaching lower-positioned areas, as access from buildings to climb-ing formwork

PERI UP Rosett Flex Staircase Alu 75Lightweight stair tower in 25 cm grid dimensions of modular scaffolding up to heights of 90 m

Consistent grid dimensionsHigh flexibility even in the smallest of spaces, all bays can be completely closed leaving no gaps

Easily adaptedFor accessing building openings with small flights of stairs on suspended bracketsStable designWith fewer ledgers in the staircase tower

Access

PERI UP Rosett Flex Staircase Steel 100 / Staircase Steel 125For heights up to 50 m, for high load-bearing requirements and convenient accessibility

High load-bearing capacity3.00 kN/m² for a run of staircase and landing of 20 mComfortable accessibilityWith sufficient space for site personnel to pass each other on the stairs

Erection without the use of toolsMounted stringers are covered with steps that safely interlock during instal-lation


PERI UP Public with Steel DeckingFulfilling the highest requirements for use in public areas

Wide range of scaffoldsAssembled as single or linked continu-ous staircases, dog-legged staircases or as stair towersComplies with all current regulationsStair geometry and landing arrangement in accordance with requirements for public access

For large public gatheringsPermissible live load 7.50 kN/m²

Protection Scaffolds

PERI UP Rosett Flex LGS Weather Protection RoofReliable protection against the effects of the weather – also for large spans

LightweightPre-assembly by hand on the ground due to the low weight of the individual componentsVariableCan be realized with different roof inclinations and geometries

MovableWith the rolling system, the roof can easily be moved by hand

Climbing Systems

FB 180 Folding Platform SystemThe universal working and safety scaffold

SimpleRequires little effort even with compli-cated ground plansAdvantageousCompensation areas as well as internal and external corners without special platforms

EfficientThe corner platform can be used for both left and right sides


CB 240 / CB 160 Climbing SystemsThe climbing brackets for supporting large-sized wall formwork

StrongLarge-sized bracket units thanks to the high load-bearing capacity of the climb-ing bracketsTime-savingPlatform including formwork movable in only one crane lift

SafeCompletely free of tripping hazards – in front of and behind the formwork

SCS Single-Sided Climbing SystemStable and flexible brackets for single-sided applications

OptimizedLarge-sized climbing units thanks to the high load-bearing capacity of the brackets, good utilization of the anchoringWell thought-outSame formwork and components for the starter and subsequent standard cycles

AdaptableSafe working conditions on inclined platforms

LPS ScreenThe lightweight climbing protection panel with a mesh enclosure

FastAssembly without a crane in a very short time; alternatively, can also be delivered pre-assembledPermeable surfaceMinimum of contact surface for the wind to gain a hold due to the mesh panel design

VariableUsed as a protection panel or with sup-plementary working platform

RCS Rail Climbing SystemThe universal modular system for a wide range of applications

SecuredAs formwork scaffolding or climbing protection panel – always rail-guidedFlexibleClimbing shoe can be attached to the walls as well as slab edges

VariableParticularly adaptable due to the modu-lar system with a regular hole arrange-ment

ACS Self-Climbing SystemSafely moved upwards with hydraulic drive without a crane

Crane-independentShuttering, striking and hdydraulic climb-ing in a fast working sequenceWeather-independentComfortably-designed platforms, also protected against wind and weather if required

High load-bearing capacityWith high load-bearing working plat-forms, e.g. for storing materials or accommodating the placing boom


Civil Engineering Technology

Framework construction with the VARIOKIT engineering construction kitCustomized constructions for virtually all geometries

Load-bearingHigh load-bearing capacities and a wide range of applicationsCombinableLoad-optimized solutions with walers, rails and main beams, combined with spindles and struts

CompleteWith all technical documents,calculations and assembly drawings

Tunnel Formwork with VARIOKIT Engineering Construction KitProject-specific solutions for tunnel construction

Continuously adjustableHeight adjustments and gridless assem-bly variants for a wide range of cross-sectionsEconomicalFewer anchors in the wall areas due to high load-bearing system walers

User-friendlyOptional with hydraulic support for shut-tering and striking as well as lifting and lowering

Bridge Formwork with VARIOKIT Engineering Construction KitFormwork solutions for bridge superstructures and cantilvered parapets

ComprehensiveBroad range of solutions for cantilevered parapets and bridge superstructuresReady at short noticeFast availability of materials due to the modular construction system

SystematicTime-saving and cost-effective assembly through standardized connections and fitting pins


VARIOKIT Engineering Construction KitEconomical supporting structure with system – materials and know-how from one source

Ingeniously simpleVersatile core components with standard connections using boltsLoad-optimisedEfficient use of materials through stati-cally optimized utlization of the compo-nents

Cost-effectiveRentable system components which remain unchanged and are extremely versatile

Special Formwork

UNO – for the monolithic construction methodSame building structures efficiently formed – horizontally and vertically in one step

Simple assemblyCustomized prefabricated individual components are quickly connectedSimply uniqueRe-usable conical ties installed from one side only

Fast and simple strikingFast striking of the walls, early strik-ing of the slabs through the drophead system

3D Formwork UnitsPrecision-made for an individual design

Custom manufacturedPrecision manufactured in the PERI formwork construction workshop on the basis of a 3D modelCost-effective realizationAlways realized with the highest pos-sible proportion of system components

Fast assemblyEasy and simple assembly on the construction site, similar to a system formwork

System-Independent Components

Formwork GirdersDecisive factor regarding the profitability of many formwork solutions

VT 20K Formwork GirderThe cost-effective solid web girder with robust steel caps on the chord ends

GT 24 Lattice GirderThe versatile formwork girder with high load-bearing capacity and excellent rigidity

PROKIT EP 110The safety system for temporary edge protection

Technically soundReliable fall protection for open edges on building shells and formworkFast assemblyVery few different lightweight system components and self-securing posts

Flexibly mountedVariable mounting possibilities on walls and slabs as well as PERI formwork and scaffolding systems


Stopend SystemsSite-compliant equipment for setting of stopends for slabs and bottom plates

Wall ClampsFor strip foundations and smaller beamsSlab Stopend AngleFor slab edges and smaller beamsSlab Stopend Bar 105For shuttering of up to 50 cm thick slabs flush with the wall

Formwork Bracket-2A single equipment for forming cantilevers as well as slab edge stopendsStopend TrestleFor forming bottom slabs of up to 60 cm thick

PROKIT EP 200The 2.00 m high side protection for increased requirements

Multi-purpose protectionProtects against falling and prevents materials falling to the groundEasily mountedLightweight foldable barriers, quickly in-stalled with tension belts and cable ties

Especially high designStandard height 2.00 m, with a third tension belt for height enclosures up to 3.90 m

Pallets and Crate PalletsFor safe transportation and optimized storage

Re-usableExtremely long service life thanks to top quality workmanshipOptimal solutionsStacking devices suitable for system components, craneable wire crates for small parts

Easy to transportCan be stacked to save space, transport-ed using a crane, forklift truck or pallet lifting trolley

Release agent PERI CleanRelease agent as well as providing protection for formwork and site equipment

For the best concrete surfacesAllows the problem-free release of the formwork from the concrete surfaceHarmlessSolvent-free and manufactured on a mineral oil basis

Protection for formwork equipmentEnsures smooth-running prop threads, protects construction equipment and machines against rust

PlywoodThe right plywood for all requirements

A very extensive programmeRanging from plywood for simple facing formwork through to coated formlining for the highest architectural concrete requirements

In all sizesAvailable in a range of standard dimen-sions; special sizes on request


PERI SoftwareThe most appropriate planning software for each user

PERI ELPOSThe fast and simple softwarefor standard applications

PERI CADThe professional software for experienced CAD users

Technical processing of formwork and scaffolding projectsIndividual planning and advice from formwork experts, customized solutions from scaffolding specialists

Optimized solutionsProject-related customized formwork and scaffolding planning with site-compliant drawings and parts lists

A personal contact personContinuous project support and techni-cal advice from a PERI specialistPlanning reliabilityThrough regulation-compliant or verifi-able static calculations

Rental Parks and DistributionThe best material in the right quantity, at the right time, in the right place

Optimal stock availabilityThrough a large rental equipment park with numerous locations around the worldSafe transportationThanks to optimized standard packaging with craneable pallets and wire crates

Uninterrupted construction sequencesDue to flexible reaction times of the PERI rental park

Field ServiceProfessional support from supervisors and project managers

Professional on-site briefingsThrough experienced PERI assembly foremen and supervisorsIncreasing the cost-efficiencyBy means of individual on-site project management

Continuous controlTarget/actual performance comparisons for the continuous monitoring of material, time and costsTransparency and planning reliabilityThanks to site-compliant and compre-hensible methods of payments

3D PlanningTangible and easily comprehensible modelling of complex and demanding construction projects

Cost transparencyThrough the tangible visualization of the technical solutionImproving the construction processThanks to animated sequence simula-tions before the project starts

Efficient construction workDue to optimized work preparation and model-based informationCoordinated processesUniform solutions – from the CAD design through to assembly

Services


Formwork AssemblyFrom plywood cut-to-size through to complex 3D elements –customized to suit all project requirements

Perfectly assembledAdapted to match the component or structural shapeWith high qualityBest quality finish due to stationary pre-fabrication using state-of-the-art manu-

facturing equipment and well-trained, experienced personnelProduced just-in-timeAssembled and delivered to the con-struction site on-time according to the construction progress

myPERI Online PortalFaster and easier access to project data around the clock

Provides an overviewProject data, materials and costs in view at all times with the help of clearly presented reportsSimplifies work processesHelpful support through useful work aids and templates in all phases of the construction process

Regularly updatedInformation is always up-to-date and the numerous evaluation options available at the click of a mouse saves time

Cleaning and RepairsSpecial service for special systems

Individually coordinatedDefinition of the required services according to the state of the materials with the PERI expertsProfessional repair serviceWith the latest plant technology con-ducted by PERI specialist personnel

Fast processingRapid processing and return deliveries thanks to PERI´s network of service centres



DE

en 0

4 | 2

014

© P

ER

I Gm

bH

PERI GmbHFormwork Scaffolding EngineeringRudolf-Diesel-Strasse 1989264 Weissenhorn, GermanyPhone +49 (0)7309.950-0Telefax +49 (0)[email protected]

Documents

Formwork Scaffolding Engineering The most appropriate ... · PDF fileFormwork Scaffolding Engineering The most appropriate solution ... formwork for building construction and civil