16
CF-37 Series Supplementary Instructions for Windows NT ® 4.0 for the model with both an internal modem and an internal LAN port Personal Computer ® Contents First-time Operation .......................................... 2 Starting Up/Shutting Down ............................... 5 Dealing With Problems (Summary) .................. 6 Reinstalling Software ........................................ 8 Specifications ................................................. 12 Modem (For CF-37VB6BACM model only) ................ 13 LAN (For CF-37VB6BACM model only) ...................... 14 Setup Utility (For CF-37VB6BACM model only) ...... 16 NOTE: NOTE provides a useful fact or helpful information. CAUTION: CAUTION indicates a condition that may result in minor or moderate injury. WARNING: WARNING indicates a hazard that may result in moderate or serious injury. [Start]-[Shut Down]: This illustration means to click [Start], then to click [Shut Down]. (For some applications, you may need to double-click.) Enter : This illustration means to press the [Enter] key. Fn + F5 : This illustration means to press and hold the [Fn] key, then press the [F5] key. Illustrations in this Manual This manual contains supplementary instructions regarding the use of the computer. It explains the cases where the operation of the computer differs from that in the Operating Instructions and Reference Manual. NT The following functions are not supported with Windows NT ® . Please ignore the description in the "Operating Instructions" about the following functions. Display Rotation Tool Battery Monitor ZV and CardBus Card USB Devices Infrared Data Communications Smart Boot An application software is needed to use the infrared data communications. The infrared data communications can not be used at 4 Mbps data transfer speed. NOTE

for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

  • Upload
    hacong

  • View
    216

  • Download
    0

Embed Size (px)

Citation preview

Page 1: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

CF-37 Series

Supplementary Instructions for Windows NT® 4.0for the model with both an internal modem and an internal LAN port

Personal Computer

®

Contents

First-time Operation .......................................... 2Starting Up/Shutting Down............................... 5Dealing With Problems (Summary) .................. 6Reinstalling Software ........................................ 8Specifications ................................................. 12Modem (For CF-37VB6BACM model only) ................ 13LAN (For CF-37VB6BACM model only) ...................... 14Setup Utility (For CF-37VB6BACM model only) ...... 16

NOTE: NOTE provides a useful fact or helpful information.

CAUTION: CAUTION indicates a condition that may result in minor or moderate injury.

WARNING: WARNING indicates a hazard that may result in moderate or serious injury.

[Start]-[Shut Down]: This illustration means to click [Start], then to click [Shut Down].

(For some applications, you may need to double-click.)

Enter : This illustration means to press the [Enter] key.

Fn + F5 : This illustration means to press and hold the [Fn] key, then press the [F5] key.

Illustrations in this Manual

This manual contains supplementary instructions regarding the use of the computer. It explains the caseswhere the operation of the computer differs from that in the Operating Instructions and Reference Manual.

NT

The following functions are not supported with Windows NT®. Please ignore the descriptionin the "Operating Instructions" about the following functions.

Display Rotation ToolBattery MonitorZV and CardBus CardUSB DevicesInfrared Data CommunicationsSmart Boot

An application software is needed to use the infrared data communications. The infrareddata communications can not be used at 4 Mbps data transfer speed.

NOTE

Page 2: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

2

First-time Operation

Confirm the inclusion of all accessories (except below Operating Instructions page 9 )

Product Recovery CD-ROMRegistration Card

Windows NT Workstation SystemPack ....................................... 1

Windows NT® BookCD-ROM Floppy Disk

Windows NT ServicePack 5 ............ 1

Windows 95 System Pack .... 1

Windows® 95 Book

4

3

The Software License Agreement will be displayed. After reading the agreement, select [I Agree].

2

1

5

Input your name and organization, then select [Next].(It is possible to omit the organization item.)

6

Input the Product Number written on the “Certificate of Authenticity” located in the Win-dows NT Book that comes with this computer then select [Next].

CAUTION

Select [Next].

To move the cursor to a particular item, press or click the desired box.

Remember this password! If the password is forgotten, Windows NT cannot be operated.

Input an Administrator password and select [Next].

Input your computer name and select [Next].

If [I Agree] is selected, the [Certificate of Authenticity] will appear. If [I Disagree] isselected, the Windows setup will be aborted.

Moving the cursor ( ) or clicking buttons can be performed with the touch pad.The Touchscreen cannot be used.

NOTE

7 Select [Next].

1

Read the steps below to help you learn what accessories are included, and to gain an understanding of some basiccomputer-related operations.

2Connect the battery pack ( Operating Instructions page 9)3Connect your computer to a power outlet ( Operating Instructions page 10)4

Read the LIMITED USE LICENSE AGREEMENT ( Operating Instructions page 22)

Turn your computer on ( Operating Instructions page 10)5 Setup Windows NT®6

FIRSTAID CD...1

8 Select [Do not connect this computer to a network at this time], then select [Next].(Settings can be made for a network even after Windows starts up. In this case, be sure toread [When Adding New Software or Hardware Components] in the Reference Manual[Technical Information].)

Driver UpdateCD.............1

Page 3: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

3

Following the display, press .Input the password set in step and select [OK], then select [Close] at the [Welcome] display.

13

9 Select [Restart Computer]. Select "Windows NT Workstation Version 4.00" and press .

6

15

14

20

18

Install the Phoenix APM 2.0 for NT by following the on-screen instructions.When the installation completes, select [Don't Restart Now].

Install the Phoenix Card Executive™ for NT by following the on-screen instructions.When the installation completes, select [Restart Now].

The [Begin Logon] display will appear. Perform the operation in step .Calibration is executed automatically. Touch the center of each red cross by followingthe on-screen instructions. At this time, a timeout will occur if no input is made in a ten-seconds period. ( "Touchscreen"). If the red cross is not touched within theperiod, select [Calibrate] in [Start] - [Programs] - [Updd].

11

12

Select [Next] at the [Card Executive 2.0 for NT Diagnostics].Select [Next], then select [Finish].Windows will restart. Select "Windows NT Workstation Version 4.00" and press .

17

The [Begin Logon] display will appear. Perform the operation in step .

19

10

10

Set the correct settings for all items in [Start] - [Settings] - [Control Panel] - [Regional Settings] and[Date/Time] etc.

It takes several minutes for the necessary files to be copied. If the computer enters theECO mode, the power to the LCD is automatically turned off. In this case, press a keyunrelated to the direct triggering of a selection, like .Ctrl

<For CF-37VB62ACM model>Install the modem driver by following the on-screen instructions.At the [COM Port Number], select [COM3], then select [OK].<For CF-37VB6BACM model>When Modem Setup appears, select [Cancel].

Enter

Install the Touchscreen driver by following the on-screen instructions.At the [Would you like to restart now], select [No]. Close the [Updd] window.

<For CF-37VB62ACM model>Install the WorldPort utility by following the on-screen instructions.<For CF-37VB6BACM model>When WorldPort Setup appears, select [Cancel].Select [Exit Setup].

Install the CrystalWave SoftSynthesis Installation for NT4 by following the on-screen instructions.When the installation completes, select [Cancel].

16

21

10

23

In [Start] - [Run], input [c:\util\msupdate\EN-X86-Q234680], then select [OK].Follow the on-screen instructions. (EN-X86-Q234680.EXE is a file for IE4.01 SP2 Y2K.)If the display asks you to restart Windows, select [Yes].

NOTE

Ctrl + Alt + Del

NOTE

Double-click the [Internet Explorer] icon to install Internet Explorer.Follow the on-screen instructions.

At the [Installation Option], by clicking , select [Full Installation], then select [Next]. At the [Confirm File Replace], press [No].Windows will restart. Select "Windows NT Workstation Version 4.00" and press .

Close the unnecessary windows.

Enter

Install the Crystal Audio driver by following the on-screen instructions.

22

Enter

When establishing settings for a network:The settings will vary for different network environments depending on the network sys-tem being used. For more details, ask your system administrator or the person in charge ofthe network. Follow the on-screen instructions.(If the LAN driver is in the floppy disk, install the driver by using the SuperDisk DrivePack after Windows Setup.)

Page 4: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

4

For reinstallation( page 8), create backup disks. To create backup disks, theoptional SuperDisk Drive Pack (CF-VFS371) and 2HD floppy disks are needed.

Eject Button

Label-side upInsert the shutter-sideheadfirst.

Turn the computer off, then remove the CD-ROM drive ( "MultimediaPocket").

1

Set the SuperDisk Drive Pack in the multimedia pocket and turn the computer on.2

3 Set a floppy disk and make sure it is not in the write-protected state, then select[Start] - [Programs] - [Panasonic] - [Create Tool Disk] and follow the on-screeninstructions. Place a label identifying the contents on each disk.

Create backup disks

Store the floppy disks in a safe place. They will enable you to return yourcomputer to factory default settings should any problems occur.

While the MP indicator ( ) is on, do not remove the floppy disk, powerdown your computer or use the suspend or hibernation function ( "Suspend/Hibernation Functions").When creating floppy disks, do not run any other application program.When creating floppy disks and the message [Insufficient files to copy] isdisplayed, press [OK] then contact Panasonic Technical Support.The Tool Disk cannot be accessed through [My Computer] or by typing the"DIR" command at the Command Prompt, because it uses a special file for-mat.

CAUTION

Names of created backup disks

Tool Disk, Backup Disk*

* There are instances where it is not necessary to create backup disks.

First-time Operation

8 Partition the Hard Disk

The hard disk includes an NT file system (NTFS) partition of 4GB. The remaining free harddisk space can be used when necessary by creating more partitions (in [Start] - [Programs] -[Administrative Tools (Common)] - [Disk Administrator]).

7 Install Acrobat® Reader 4.0

2

3

1 In [Start] - [Run], input [c:\util\reader\Ar40eng.exe], then press [OK].

After reading the "Software License Agreement", select [Accept] if you agreeto the terms.

Press [Next].4

5

Press [Next] and set up the Acrobat® Reader 4.0.

At the [Setup Complete], Select [Yes, I want to restart my computer now], then select[Finish].

Acrobat® Reader is necessary to view the Reference Manual, which explains de-tailed operational procedures concerning your computer.

NOTE

CAUTION

The sector showing [Unknown] is an important sector and must not be deleted.

Page 5: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

5

1 Open the display ( Operating Instructions page15)

Starting Up/Shutting Down

Starting Up

2 Turn your computer on ( Operating Instructions page 15)

3 Select your operating systemSelect "Windows NT Workstation Version 4.00" and press Enter .

LogonWait for 10 seconds after confirming that the HDD access has been completed, then press Ctrl +

Alt + Del .

4

5 Input your password

6 Select your applicationYou are able to start working on your computer.

NOTE

Input the user name and password, then press [OK]. If [Cancel] is clicked, the computer will return tothe initial [Begin Logon] display. Until the correct user name and password are entered, the computerwill not operate.

1

Shutting Down (power off your computer)

2 Confirm shut down

Select [Shut down].

Your computer will power off automatically.(In the OFF state, if you are not recharging your battery pack or if the pack is fully charged, your computer consumesapproximately 1.5 W.)

Display the shut down screen ( Operating Instructions page 16)

NOTE

For the computer to automatically shut down after [Shut down] is selected, Phoenix APM 2.0 for

Windows NT® has to be installed. When and are displayed on the taskbar, this indicates thatthe program is installed.

This procedure is shutting down without using the suspend or hibernation function.

Restarting your computer (without shutting down) ( Operating Instructions page 16)

The power saving function is factory set to remove power from the LCD if the computer is notoperated or no access is made to a device for two minutes. The LCD will resume normal operationif the touch pad is moved or if a key on the keyboard is depressed.

Page 6: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

6

Dealing With Problems (Summary)

When a problem occurs, refer to this page. The Reference Manual also contains detailed information. If you still cannot trouble-shoot the problem, contact Panasonic Technical Support.

Starting Up

The power indicator or bat-tery indicator is not lit

is displayed

[POST Startup Error(s)] isdisplayed

Windows startup, or an op-eration is extremely slow

The date and time areincorrect

When the previous item isnot the cause

NT does not start

Check the cable connection for the AC adapter.Check to see if a fully charged battery is properly installed.Remove the battery pack and disconnect the AC adapter, then connect them again.

Input your password. If you have forgotten it, contact Panasonic Technical Support.

Operating Instructions page 17

Press F9 in the Setup Utility ( "Setup Utility"). This will restore the SetupUtility's settings to their default values (except the password settings). Then, the Setup Utilitymust be run once again for you to input the appropriate operating environment settings. (Theprocessing speed depends on the application software used, so this operation may not cause theprocessing speed to increase.)

You can set the date and time through [Date/Time] in [Start] - [Settings] - [Control Panel].If you continue to experience problems, the internal battery maintaining the clock mayneed to be replaced. Please contact Panasonic Technical Support.

When the computer is connected to a Local Area Network (LAN), please confirm the dateand time of the server.When [APM 2.0 for NT] is not displayed in [Control Panel], this indicates that PhoenixAPM 2.0 for Windows NT® is not installed. When the suspend or hibernation function isused under this condition, the date and time may be incorrectly displayed. Correct the dateand time, and then install Phoenix APM 2.0 for Windows NT®. You can set the date andtime through [Date/Time] in [Start] - [Settings] - [Control Panel].

Press F9 in the Setup Utility ( "Setup Utility"). This will restore the SetupUtility's settings to their default values (except the password settings).Try removing all peripheral devices.

If [Cancel] at the [Path not found] is clicked during the LAN card driver installation, the nexttime the system is activated it will hang up without NT being activated.In such cases, follow the steps listed below.

1 Power off, then power on again.2 If [Press spacebar NOW to ...] is displayed, press the space key.3 If [Hardware Profile/Configuration Recover Menu] is displayed, press L Enter .4 At the [PCMCIA Card Not Configured], select [OK].5 At the [Path not found], set the floppy disk included with the LAN card, then select [OK].

Follow the on-screen instructions.

The red indicator lights.Repeated beeping soundwhile the computer is in use

The red indicator blinks

After the AC adapter is con-nected, the orange indicatorblinks five times

The battery level is low. Save your data and power off your computer.After connecting the AC adapter or replacing the battery pack with a fully charged one, turnyour computer on.

The battery pack or recharging function may be defective. Quickly remove the batterypack and disconnect the AC adapter, then connect them again.If the problem persists, contact Panasonic Technical Support.

Unable to charge because of an improper temperature range. ( Operating Instructionspage 6)

Battery Indicator

Page 7: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

7

No display after poweringon

The power has not beenturned off, but after a cer-tain period of time, there isno display

The resolution of the displaycannot be changed

An afterimage appears(i.e.,green, red, and blue dots re-main on the display) or thereare dots not displaying the cor-rect colors

During simultaneous dis-play, the screen of the exter-nal display becomes disor-dered

The external display nolonger displays properly

At the time of purchase, the display setting is preset for an external display. If you connectan external display, the screen is displayed on the external display.When there is no display to an external display,• Check your cable connection to the external display.• Confirm your display is powered on.• Check the settings for your external display.Try changing the display by pressing Fn + F3 .When displaying only through an external display, if the computer is shut down by usingthe suspend or hibernation function, there will be no display on the LCD unless the exter-nal display is connected when operations are resumed. In this case, connect the externaldisplay.

Has the computer been set to the power-saving mode?To resume operation of your computer from ECO mode, press any key.To save power, your computer may have automatically entered the suspend or hiberna-tion mode. ( "Suspend/Hibernation Functions")

Set [None] for [Wallpaper] in [Start] - [Settings] - [Control Panel] - [Display] - [Background],and then press [OK]. Then, once again try changing the resolution. After the change, besure to restart the computer.

If an image is displayed for a prolonged period of time, an afterimage may appear. Thisis not a malfunction. The afterimage will disappear when a different screen is displayed.

High-precision and advanced technologies are necessary in the production of color liquidcrystal displays (color LCDs). Therefore, if 99.998% or more of the picture elements arefunctioning properly), no defect is considered to exist.

Try changing the display by pressing Fn + F3 .

When an external display not compatible with the power saving mode is used with the com-puter, the external display may no longer display properly when the computer enters theECO mode. In such cases, turn off the power to the external display.

Display

Page 8: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

8

6 Select [1. Initialize and restore the HDD], press .

7 At the confirmation message, press .

8 When the message "Remove a floppy disk from the

SuperDisk drive, and turn the computer off. Replace

the SuperDisk drive with a CD-ROM drive. Then,

follow the instructions in the manual." is displayed,

follow on-screen instructions.

(1)Replace the SuperDisk drive with the CD-ROM drive.

(2)Turn the computer on.

(3)When the message [Press <F2> to enter SETUP] is

displayed, press and then run the Setup Utility.

(4)Press F9 .

At the confirmation message, select [Yes] and press

Enter .

(5)Select [Boot] menu, press F5 / F6 and /

until [CD-ROM/DVD-ROM] is at the top of the

[Boot] menu and [ATAPI Removable] is the next

position.

(6)Select [Power] menu and set [Power Management]

to [Disable] , [Power Switch] to [Off] and [Fn + F7/

Fn + F10 key] to [Disable].

(7)Insert the Windows NT 4.0 Workstation CD-ROM.

(8)Press F10 . At the confirmation message, select

[Yes] and press Enter . The computer will reboot.

9 At the [Welcome to Setup], press Enter .

10 At the [Setup has recognized the...], press Enter .

If the message [Setup has determined that...] is dis-

played, press Enter .

Reinstalling

CAUTION

If data on your hard disk is compressed, the data shouldbe uncompressed.

Windows NT (reinstalling)

1 Replace the CD-ROM drive with a SuperDisk drive.

Insert the Tool Disk, and turn the computer on.

2 When the message [Press <F2> to enter SETUP] is

displayed, press F2 and then run the Setup Utility.

3 Press F9 .

At the confirmation message, select [Yes] and press

Enter .

4 Select [Power] menu and set [Power Management] to

[Disable] , [Power Switch] to [Off] and [Fn + F7/Fn +

F10 key] to [Disable].

5 Press F10 . At the confirmation message, select

[Yes] and press Enter . The computer will reboot

and this screen should appear.

1. Initialize and restore the HDD

2. Exit

Reinstalling Software

Before Reinstallation

Preparing

Important

FIRSTAID CDWindows NT Workstation CD-ROM included in the Windows NT Workstation System PackWindows NT Service Pack 5 CD-ROMTool Disk you made earlier

If you have not created the Tool Disk, you can create by selecting [Create Tool disk] in [Start] - [Programs] -[Panasonic]. If you can not create this disk, contact Panasonic Technical Support.

NOTE

The SuperDisk Drive Pack (CF-VFS371) is required for the following reinstallation procedure.( "SuperDiskDrive")

Save all important data. If reinstallation is carried out, all data existing prior to the installation will be lost. Thereinstallation will return the computer to close to the conditions at time of purchase.

Before the reinstallation procedure, remove all peripherals (except for the SuperDisk drive). Be sure the AC adapter is connected until the reinstallation procedure is completed. When the computer enter the ECO mode, the computer to the LCD is automatically cut. In this case, perform the touchpad operation.

Enter

Enter

F2

Page 9: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

9

36 Set the Firstaid CD into the CD-ROM drive and select

[Start] - [Programs] - [Command Prompt]. Input the fol-

lowing at the MS-DOS prompt (C:\>).

d: Enter

install.bat Enter37 Input the following and then close [Command Prompt].

exit Enter

<When one or more Backup Disks have been created>

Shut down the computer, then replace the CD-ROM

drive with a SuperDisk drive. For each disk starting

from the second disk, (in the order given) set the disk into

the SuperDisk drive and select [Start] - [Programs] -

[Command Prompt]. Input the following.

a: Enterinstall.bat Enter

Input the following and then close [Command Prompt].

exit EnterShut down the computer, then replace the SuperDisk

drive with a CD-ROM drive.

Power on. (Perform step 35.)

System setup

Display driver38 Select [Change] for [Adapter Type] in [Start] - [Settings] -

[Control Panel] - [Display] - [Settings] - [Display Type].

39 Select [Have Disk] at the [Change Display], input

[c:\util\drivers\video], then press [OK].

40 Select [Silicon Motion Lynx Family], then select [OK].

41 Select [Yes] at the [Third-party Drivers]. At the [Install-

ing Driver], select [OK].

42 Select [Close] at the [Display Type], then select [Close]

at the [Display Properties].

If the display asks you to restart Windows, select [Yes].

(Perform step 35 after Windows restarts.)

43 At the [Invalid Display Settings], select [OK].

44 At the [Display Properties], set [65536 Colors] for the

[Color Palette], set [800 by 600 pixels] for the [Desktop

Area], select [Test] then select [OK].

45 If there are no problems with the testing mode, select [Yes]

then select [OK] at the [Display Properties].

14 Select [Format the partition using the NTFS file sys-

tem], then press Enter .

Formatting will begin automatically.

15 Without changing the location (\WINNT) of the instal-

lation, press .

16 Press Enter to start the examination of your hard

disk. The copying of files will begin automatically.

17 If the message [This portion of Setup has completed success-

fully.] is displayed, do not remove the CD-ROM. Press

Enter .

18 Windows will restart. When [Press <F2> to enter Setup]

is displayed, press F2 and run the Setup Utility. If the

Setup Utility is unable to be run, turn the power off after the

[Welcome to Setup] is displayed, and perform step 18 again.

19 Press F9 . At the confirmation message, select

[Yes] and press Enter .

20 Press F10 . At the confirmation message, select

[Yes] and press Enter . Windows will restart several

times.

21 At the [Windows NT Setup], select [Next].

22 At the [Setup Options], select [Typical] then select [Next].

23 Input your name and organization then select [Next].

(It is possible to omit the organization item.)

24 Input the Product Number written on the "Certificate

of Authenticity" located in the Windows NT Book that

comes with this computer then select [Next].

To move the cursor to a particular item, press or

click the desired box.

25 Input your computer name then select [Next].

26 Input an Administrator password then select [Next].

27 At the [Emergency Repair Disk], select [No, do not create an

emergency repair disk.], then select [Next].

28 At the [Windows NT Components], select [Install the most

common components (recommended)], then select [Next].

29 At the [Windows NT Setup], select [Next].

30 Select [Do not connect this computer to a network at

this time] and select [Next], then select [Finish].

31 At the [Date/Time Properties], set the correct settings

CAUTION

Remember this password! If the password is forgot-ten, Windows NT cannot be operated.

35 At the [Begin Logon], press Ctrl + Alt + Del .

Input the password set in step 26 and select [OK], then

select [Close] at the [Welcome]. (This step has to be per-

formed each time the computer is started up.)

Enter

then select [Close]. (Default: GMT)

32 At the [Detected Display], select [OK].

33 At the [Display Properties], select [OK].

34 If the message [Windows NT 4.00 has been installed suc-

cessfully.] is displayed, remove the CD, then press

Enter

11 Read the entire [Windows NT Licensing Agreement] (use

to scroll down) and press F8 .

12 A list of hardware and software will be displayed. Con-

firm the contents and press Enter .

13 Select [Unpartitioned space] (the largest size), then press

C .

Input [4095] at the [Create partition of size], press Enter .

Select [C:New (Unformatted) 4095MB] , press Enter .

Page 10: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

10

Reinstalling Software

Windows NT Service Pack Setup

1 Set the CD for Windows NT Service Pack 5 into the CD-

ROM drive. Microsoft Internet Explorer will begin to

run automatically.

2 Scroll down the display then select [Install Service Pack 5 for

Intel-based Systems].

3 At the [Confirm File Open], select [Open].

4 Read the [Software License Agreement], and check [Ac-

cept license Agreement], then select [Install].

5 Select [Restart].

6 When Windows restarts, remove the CD. (Perform step

35 after Windows restarts.)

Installing Phoenix APM

(Windows NT Service Pack 5 has to be installed before the

following steps.)

1 In [Start] - [Run], input [c:\util\drivers\apm\setup.exe],

then select [OK].

2 Press the button to install.

At the [APM 2.0 for NT Setup], select [OK].

If the display asks you to restart Windows, select [Re-

start Now].

(Perform step 35 after Windows restarts.)

Installing Touchscreen

1 In [Start] - [Run], input [c:\util\drivers\tscreen\setup.exe],

then select [OK].

2 Select [Next].

3 Read the License Agreement, then select [Next].

4 At the [Folder], select [Next].

5 At the [Directory], select [Next].

6 Confirm [Place icons in system tray] is selected, then

select [Next].

7 At the [Serial Settings], confirm that [Auto Detect] is se-

lected, then select [Next].

8 At the [Ready to install], select [Next].

9 At the [Complete], select [Finish].

10 If the display asks you to restart Windows, select [Yes].

(Perform step 35 after Windows restarts.)

11 Calibration is executed automatically. Touch the centerof each red cross by following the on-screen instructions.

Installing modem

1 In [Start] - [Run], input [c:\util\drivers\modem\setup.exe],

then select [OK].

2 At the [Modem Setup], select [Install].

3 Select [Com3] in [COM Port Number], then press [OK].

Installing World Port

1 In [Start] - [Run], input [c:\util\drivers\modem\wport\setup.exe],

then select [OK].

2 Select [Next].

3 Confirm that the [Destination Folder] is [c:\program

Files\Gateway\WorldPort], and then select [Next].

4 Confirm that [World Port] is selected for [Select Program

Folder], then select [Next].

5 Select [Finish].

1 In [Start] - [Run], input [c:\util\drivers\sound\setup.exe], then

select [OK].

2 Select [Next].

3 In [Start] - [Run], input [c:\util\drivers\sound\softmidi\setup.exe],

then select [OK].

Select [Install Driver].

Select [Restart].

(Perform step 35 after Windows restarts.)

Installing Sound Driver

DMI Viewer setup

46 Insert the FIRSTAID CD.

47 In [Start] - [Run], input [d:\en\dmi\setup.exe], then

select [OK]. Select [Next].

DMI Viewer setup will start automatically.

48 Select [Yes, I want to restart my computer], then se-

lect [Finish]. (Perform step 35 after Windows re-

starts.)

NOTE

<For U.K.>Select [English [United Kingdom]] in [Regional Settings]-[Input Locales].

Page 11: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

11

Installing Acrobat® Reader 4.0

page 4

1 In [Start] - [Run], input [c:\util\drivers\pccard\setup.exe],

then select [OK].

2 Press the button to install.

At the [Creating Control Panel], read the message, then

select [I Understand].

At the [Card Executive 2.0 for NT], select [OK].

If the display asks you to restart Windows, select [Restart

Now].

(Perform step 35 after Windows restarts.)

3 At the [Card Executive 2.0 for NT Diagnostics], select[Next].

4 Select [Next], and select [Finish]. Windows will restart.

(Perform step 35 after restarting the computer.)

Installing Phoenix Card Executive

1 In [Start] - [Run], input [c:\util\writing\setup.exe], then

select [OK].

2 Select [Next].

Setup will start automatically.

3 Select [Finish].

4 In [Start] - [Shut down], select [Restart], then press [OK].

Installing Panasonic Hand Writing

Reinstalling Windows NT causes an older version of Internet

Explorer to be installed.

To return the computer to the state it was in when you pur-

chased it, follow the steps below to install the newer version

of Internet Explorer.

(Windows NT Service Pack 5 has to be installed before the

following steps.)

1 Set the CD for Windows NT Service Pack 5 into the CD-

ROM drive. Microsoft Internet Explorer will begin to

run automatically.

2 Select [Microsoft Internet Explorer 4.01 Service Pack 2].

3 Select [Install IE4.01 SP2 for Intel-based Systems].

4 At the [Confirm File Open], select [Open].

5 At the [Internet Explorer 4.01 SP2 Active Setup], select [Next].

6 Read the [License Agreement] and select [I accept the

agreement], then select [Next].

7 At the [Installation Option], by selecting , select [Full

Installation], then select [Next].

Follow the on-screen instructions.

At the [Confirm File Replace], select [No].

Installing Internet Explorer 4.01

8 When the message indicating the end of the installation

operation appears, select [OK].

If the display asks you to restart Windows, select

[OK]. After Windows restarts, remove the CD. (Per-

form step 35 after restarting the computer.)

9 In [Start] - [Run], input [c:\util\msupdate\EN-X86-

Q234680.exe], then select [OK].

1 Set the Windows NT 4.0 Workstation CD into the CD-

ROM drive.

2 Select [Start] - [Programs] - [Command Prompt].

3 At the prompt, input the following:

xcopy d:\i386\*.* c:\winnt\i386\*.* /s Enter

If asking you to insert the Windows NT 4.0 Worksta-tion CD after reinstallation, input [c:\winnt\i386] forthe folder name.

After reinstallation, execute the following.

NOTE

4 At the prompt, input the following:

exit Enter

Page 12: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

12

Model No. CF-37VB62ACM CF-37VB6BACM

Internal LAN IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX

Software Operating System Microsoft® Windows NT® 4.0 with Service Pack 5

Utility Programs Setup Utility, DMI Viewer, Phoenix APM 2.0 for Windows NT®

Phoenix Card ExecutiveTM 2.0 for Windows NT®, Hand Writing

Specifications

Except below Operating Instructions page 25

Page 13: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

13

CAUTION

NOTE

Modem (For CF-37VB6BACM model only)

1 Connecting a telephone line to the internal modemIt is not possible to connect the internal modem to any of the following lines.

Internal home phones Intercoms

There are cases telephone construction (or installation) work will be necessarydepending on the shape of the connector of the telephone line.

Do not use the PBX internal phone lines installed in company offices. Doing somay lead to a fire or electric shock.

2

Be sure to make separate settings to connect to network services like the Internet orto use e-mail.

When using the internal modem, set [Internal modem/LAN] to [Enable]* in the Setup Utility.(* Default)

3

Select [Start] - [Run], input [D:\WINNT40\MODEM\SETUP.EXE], then press[OK].

At the [Modem Setup], select [Install].

At the [COM Port Number], select [COM3], then press [OK].

Restart the computer.

CAUTION

There are cases the modem will not work properly when this setting is incorrect.

NOTE

Do not use the suspend and hibernation functions during communications.

Performing the "Telephony" settings for the modem

Install the modem driver

2

3

1

4

5

Set "Driver Update CD" to the CD-ROM Drive.

At the [Area code], input the area code number.

At the [Dial Using], select [Tone or Pulse].

Select [OK] ([Close] at the first time operation).

2

3

1

4

Select [Start] - [Settings] - [Control Panel] - [Telephony], set [I am in thiscountry/region] ([What country/region are you in now?] at the first timeoperation).

NOTE

The above settings can be changed in [Control Panel] - [Mini PCI Winmodem].

Page 14: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

14

13

Input [D:\WINNT40\LAN] and then press [Continue] at the second [Windows Setup].

LAN (For CF-37VB6BACM model only)

LAN Port

CAUTION

Do not insert a telephone line connector (including a PBX internal phone) intothe LAN port. Doing so may cause fire or electric shock.

FCC Regulation Notice for modemThis equipment contains a FCC approved modem.

Manufacturer of modem: 3Com CorporationModel No. 3CN3AC1556

FOR HOME OR OFFICE USE

Tested To ComplyWith FCC Standards

When using the LAN, set [Internal modem/LAN] to [Enable]* in the Setup Utility.(* Default)

1

2

Select [Network] in [Start] - [Settings] - [Control Panel].

Select [Yes].

Select [Wired to the network] and then press [Next].

Confirm [3Com 10/100 Mini PCI Ethernet Adapter] at the [Network Adapters].

Input [D:\WINNT40\LAN] and then press [OK].

Select [Select from list] and then press [Have Disk].

Press [Next].

Select your [Protocol] and then press [Next].

Select your [Network Service] and then press [Next].

Press [Next].

Input [C:\WINNT\I386]* and then press [Continue] at the first [Windows Setup].

Do not use suspend and hibernation functions during communications.When using the computer as a network computer, some additional settingsmay have to be made depending on the usage conditions. We recommendasking your system administrator or the person in charge of the network.

NOTE

Connecting a line to the LAN Port

Install the LAN driver

1 Set "Driver Update CD" to the CD-ROM Drive.

2

3

4

5

6

7

8

9

11

12

10

NOTE

Replace "For U.S.A." ( Operating instructions page 3) for the following.

Confirm [3Com 10/100 Mini PCI Ethernet Adapter] at the [Select OEM Option],then press [OK].

14

* After the reinstallation ( Page 11), set the Windows NT Workstation CD-ROM included inthe Windows NT System Pack and then input [D:\I386].

Page 15: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

15

Wake up from LAN

This is a function to automatically power on the computer from a network server. To use thisfunction, it is necessary to have a network environment that accommodates Wake up from LAN(for a Local Area Network).When using this function, set [Wake up from LAN] to [Enable] with the Setup Utility. ( page 16)

Be sure to connect the AC adapter, and enable the supply of power.Make settings to allow the use of a Local Area Network.Be sure to leave the LCD panel open when [Panel Switch] is set to [Suspend] or[Hibernation] in the Setup Utility.When using the Wake up from LAN function, User Password is not necessary even if[User Password] has been set in the Setup Utility.When [Wake up from LAN] in the Setup Utility is set to [Enable], remaining batterypower will dissipate in about three days. In particular, note that when the computer ison standby using the suspend function, data in RAM memory may be lost. We recom-mend that when not using the Wake up from LAN function, you should keep theabove setting on [Disable].The Wake up from LAN function will not operate under the following conditions:

NOTE

- When the computer has been placed in suspend or hibernation from MS-DOS mode.- When the computer has been shut down by pressing the power switch for more than

four seconds.- When the password has been input incorrectly, and the computer has returned to

suspend, hibernation, or power off status.

Do not use suspend and hibernation functions during communications.When using the computer as a network computer, some additional settings mayhave to be made depending on the usage conditions. We recommend asking yoursystem administrator or the person in charge of the network.

NOTE

15 Select [Continue].

Select [Start] - [Run], input [C:\SP5\SP5I386.EXE], then press [OK].Follow the on-screen instructions.The settings will vary for different network environments depending on the networksystem being used. For more details, ask your system administrator or the person incharge of the network.

16

Page 16: for the model with both an internal modem and an internal ... · CF-37 Series Supplementary Instructions for Windows NT® 4.0 for the model with both an internal modem and an internal

16

Plug & Play: [Disable]Serial Port A:* [Auto]Serial Port B:* [Auto]Device: [Touchscreen]

Parallel Port:* [Auto] Mode: [Bi-directional]Internal Modem/LAN: [Enable] Wake up from LAN: [Disable]

Internal Modem/LAN

Wake up from LAN

1. [ATAPI Removable]*2. [Hard Disk]3. [CD-ROM/DVD-ROM]4. [Network]**

Except below Reference Manual page 41

The default order is as follows: [ATAPI Removable] [Hard Disk] [CD-ROM/DVD-ROM] [Network].

To move a device up by one in the order, select the device with , and then press F6 .

To move a device down by one in the order, select the device with , and then press F5 .

* The SuperDisk Drive is included in [ATAPI Removable].** When [Network] is the top of the menu, the computer is booted from LAN.

Parameters ( : Default)

Disable

Enable

Disable

Enable

Except below Reference Manual page 38

UA0200-0DFQX2817ZAUPrinted in U.S.A.

CopyrightThis manual is copyrighted by Matsushita Electric Industrial Co., Ltd. with all rights reserved. No part of this manual may bereproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd.No patent liability is assumed with respect to the use of the information contained herein.

© 2000 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.

DisclaimerComputer specifications and manuals are subject to change without notice. Matsushita Electric Industrial Co., Ltd. assumes noliability for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals.

TrademarksPS/2™ is a trademark of International Business Machines Corporation.Microsoft, MS-DOS, Windows and Windows NT are registered trademarks of Microsoft Corporation of the United States and/orother countries.Pentium is a registered trademark of Intel Corporation.Phoenix Card Executive is a trademark of Phoenix Technologies Ltd.Acrobat is a registered trademark of Adobe Systems Incorporated.Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd.

Setup Utility (For CF-37VB6BACM model only)

* If [Enable] is set, sub items will be displayed.

Advanced Menu

Boot Menu